lg_42_inch_plasma_tv_training_manual_[et]

Upload: eric-creech

Post on 08-Apr-2018

219 views

Category:

Documents


0 download

TRANSCRIPT

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    1/79

    4 2 I n c h ( W i d e ) P D P S V C T r a in i n g M a n u a

    LG Electronics / DND QA

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    2/79

    Contents

    . Usage/Service Points to be concerned

    . Module formation & spec

    . Screen defect diagnosis1. 4/7 or 3/7 of screen is not displayed.

    2. Screen by Data COF is not displayed.

    3. one or more of Data COF IC have regular vertical lines.

    4. Data COF IC unit error pattern

    5. The screen by Scan COF is not displayed.

    6. Regular- interval vertical line in the whole screen.

    7. Vertical data copy

    8. One or more vertical bars.

    9. One or more horizontal bars.

    10. Input signal pattern is displayed but the whole brightness of screen is dark.

    11. In full white pattern, foreign color is displayed or in full black pattern, mis-discharge is partially occurred..

    12. In full white pattern, the brightness is getting darker toward the center.

    13. A specific brightness of one color is not clear.

    . Non-picture defect diagnosis

    . One Point Service Guide(42 Inch, 40 Inch)

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    3/79

    LG Electronics/DND QA G3/79

    Usage/Service points to be concerned

    SUGGGESTIONS

    1. Static precautionDrive section circuit is C-MOS circuit, so to protect against static electricity, wear static-proof wrist band.

    2. Cleaningwhen wiping panel, do not use liquid cleaner or other chemicals . Use a damp cloth for cleaning .

    3. handlingColor PDP uses high voltage(Max.500V). Be aware of electronic shock when handling PDP Unit and dont touch drive circuit.and even driver circuits capacitor is turned off but charge still remains there, so to touch drive circuit, be sure to wait at least 1 minute.

    4. Warning when connecting signal & Power Connector in operationdo not touch connector while Color PDP is operating.

    5. PDP servicing and guaranteeGlass Panel and Drive Circuit section are linked and operating together.if you disassemble and assemble the product in your own hands , LGE is exempted from the guarantee of function, quality and etc.

    6. Damage in still imageColor PDP uses fluorescent material. The quality of PDP fluorescence by nature becomes deteriorated if using it in the same condition of CRT.To prevent this symptom, input full-screen regularly or use screensaver software.

    So do not display the still image for a long time.

    7. Temperature & ventilationColor PDPs Glass Panel section and Drive circuit section emit the heat so the temperature shall be kept under 40.the temperature of glass panel section is pretty high because built-in drive circuit emits the heat.PDP is operating with high voltage therefore be sure to keep it away from conductive objects.

    8. Warning when handling Modulebe aware that PDP shall not be touched by metal or hard objects and shocked by the heat or mechanical force.be careful when disassembling or handling.be sure to wear glove for preventing injury when the glasss broken.

    Color PDP is a display device consisting of Panel section &Drive section. Panel section is composed of electrode,

    fluorescent substances ,dielectrics and gases, and drive section is a combination of electrical circuit section and

    PCB section. We call this concrete as PDP Module Assy and the following shows warning.

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    4/79

    LG Electronics/DND QA G4/79

    Service warning

    1. One DVM ( FLUKE 87 or similar type )

    2. Digital Oscilloscope ( over 200MHZ )

    Defect diagnosis tool

    1. When inserting parts or PCB, fasten the lead line to terminal before soldering.

    2. When inserting high- voltage resistance(metal oxide film resistance or metal film resistance), keep 10mm away from PCB

    3. High-voltage or high-temperature parts shall be away from the lead line.

    4. This chassis is insulation(cold) chassis but for safety, it is better to use insulation trance.

    when servicing power board, be sure to use insulation trance.

    5. While PDP Module is in operation, do not connect or remove lines.

    With COF or panel defect, report it to LGE PDP module service department.

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    5/79

    LG Electronics/DND QA G5/79

    Power : 220V 60HzPower consumption : 340W

    1056

    1259

    635

    693.5

    220

    779.51379

    114.8

    281

    82

    91.5

    spect ratio: 16:9reen size (H X V) : 920.1 X 518.4mmsolution : 852 X 480 (VGA)

    ell Pitch (H X V) : 0.36 X 1.08isplayable colors (R,G,B) : 1,677K (256 X 256 X 256)rightness : 250 cd/ (w/o filter : 550 cd/ )ntrast ratio : 250:1 (w/o filter ; 700:1 )

    color temperature : over 8500 Kviewing angle : over 160input signal : NTSC, HD, VGA ,SVGATwin Picture : PC/AVPC input : D-SUB 15Control : D-SUB25 / STB connectionVideo input : CVBS

    S-Video inputDVD input(Y,Cb,Cr)/R,L : Y/Y. Pb/Cb, Pr/Cr+R/LAudio input : R/LPower Cable : 3 (Ground terminal)Sound Output (Speaker) : R.L OutR,G,B input : D-SUB25 (RGBHV) : STB connectioAC Input : 220V 60Hz

    MN-42PZ10 Spec & Feature

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    6/79

    LG Electronics/DND QA G6/79

    ITEMS SPECIFICATIONS(Tentative)Screen Size: 42 inch/ 106cm diagonalAspect Ratio: 16 :9 (width:height)Resolution: 852 x 480 Pixels(SD grade)

    Peak Brightness : typ.240cd/m (with filter 60%)Contrast Ratio: 700:1(Dark Room & with filter 45%)Viewing Angle: 160 horizontally and verticallyDisplayable Colors: 16.7 millionWeight: kg (MNT), kg(D/stand), kg(spk.)x2Life: >25,000 hours

    (elapsed time to 50% of initial brightness)Dimensions(MNT) : 105.6cm wide, 63.4cm high, 8.2cm deep

    Input Terminals : RF terminal(PAL/SECAM/NTSC)(Set Top Box) Composite Video input(RCA) X 2, S-Video

    Audio L&R input(RCA) X 2

    Component Video (Y,Pb,Pr) + R/L for DVDComponent Video (Y,Pb,Pr)+ R/L for HDTV Stb.RGB-SUB 15 pin for HDTV Stb.(480p/720p/1080i)Analog RGB-SUB 15pin(PC VGA ~SVGA)

    Stereo Input for PC AudioOutput Terminals : Analog RGB-SUB 15 pin(PC/DTV input bypass)(Set Top Box) Audio L&R(RCA)

    RGB-SUB 25 Pin for MNT(RGB/HV in & Control)Composite Video output + R/L output

    Input Terminals : Analog RGB-SUB 15 pin (Compatible with PC(MNT) VGA ~SVGA, Compressed XGA)

    RGB-SUB 25 Pin for STB(RGB/HV in & Control)Component Video (Y,Pb,Pr) for DVD & DTV Stb.

    Composite Video input(PAL/SECAM/NTSC)Audio L&R input(RCA)X2

    Display Frequency : 15.73kHz to 60kHz horizontally, 50Hz to 75Hz(V)Picture : PIP(2Tuner:STB), Twin Picture, Digital Comb filter, Digital Video Enhancer(Jagging free )Sound : A2 stereo, AVL, Dolby Virtual, 2x10WrmsRemote Control : Included(Unified)External Control : D-sub 25-pin connectorPower Source : 110-240V , 50/60 HzPower Consumption: 300 watts( with Max. Audio : 320W)

    MN-42PZ10(42W PDP MNT)Market : Korea / N_ America / S_America

    (2001. July ~)

    Spec of Models

    RN-BA11(3 System Multi STB)430(W)X78(H)X280mm(D)

    (Example of Desk Top Type)

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    7/79

    LG Electronics/DND QA G7/79

    DIGITAL SET TOP BOX ( SK-011T )

    DIGITAL SET TOP BOX ( SK-010T )

    ANALOG SET TOP BOX ( RN-BA10 )

    ANALOG SET TOP BOX ( RN-BA11 )

    MN-40PA10, MN-40PA10A only

    MN-42PZ10 only

    MN-40X3M , MN-40PA10, MN-40PA10A, MN-42PZ10, MN-60PZ10

    MN-40PA10, MN-40PA10A, MN-42PZ10, MN-60PZ10

    All but MN-40X3M can be used

    SET TOP BOX Compatible Model

    Only related model can be used.

    Only related model can be used

    all Model can be connected but because of noise problem with internalfan, it is terminated.Be sure that MN-40X3M is not compatible with SK-01

    Separately : dedicated cable (AP-EA10)

    separately : dedicated cable (AP-EA10)

    PDP STB type & compatible mod

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    8/79

    LG Electronics/DND QA G8/79

    P3 P2

    VR2 VR1 VR1

    Y SUS B/D ASSY CTRL B/D ASSY

    ZSUS B/D ASSY

    X RIGHT B/D ASSY

    Label

    P2

    P100

    P300

    P1X LEFT B/D ASSY

    P4

    P6

    P5

    Y

    DRV

    Upper

    B/DASSY

    Y

    DRV

    Lower

    B/D

    ASSY

    P1

    P2

    . Module diagram & spec

    PART NO. product name standard1 6871QT H003 BPWB( PCB) AS SYZCNT T OP B/D AS SY2 6871QZ H002 BPWB( PCB) AS SYZSUS B /D ASS Y3 6871QT H004 BPWB( PCB) ASS YZCNT BO TTO M B/D ASS4 6871QL H012 APWB( PCB) AS SYX LEFT BO TTO M B/D A5 6871QR H010 APWB( PCB) AS SYX RIGH T BOTT OM B/D6 6871QD P016 BPWB( PCB) ASS YYDRV Up per B/D AS SY7 6871QD P017 BPWB( PCB) ASS YYDRV Lo wer B/D AS SY8 6871QY H015 APWB( PCB) AS SYYSUS B /D ASS Y

    YDRV B/D ASSY

    ZCNT TOP B/D ASSY

    ZCNT BOTTOM B/D ASSY

    EXTERNAL CABLE CONNECTION

    connector supply signalP1~P2[X B/D] 5V, 15V, VAP3[Y SUS B/D] VSC, VSETUPP2[Y SUS B/D] 5V, 15V, VSP1[Z SUS B/D] 5V, 15V, VSP300[CTRL B/D] 5V

    P100[CTRL B/D] VIDEO SIGNAL

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    9/79

    LG Electronics/DND QA G9/79

    Y- Board

    ControllerBoard

    Z- Board

    CN1

    CN2

    Local key

    EMI Filter

    VSCBoard

    POWERBoard

    X Board ( R )X Board ( L )

    Y-Drive

    Y-Drive

    Main Power

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    10/79

    LG Electronics/DND QA G10/79

    STBSTB

    PCPC

    VideoVideo

    DVDDVD

    LA7222LA7222

    VPC3230VPC3230 SDA9410SDA9410 CXA2101CXA2101 THS8083THS8083

    CXA2022SCXA2022SMX88L284MX88L284

    BufferHC541BufferHC541

    LA4282LA4282

    MICOMCXP750010

    HC74HC74

    PDPMPDULE

    2M-SDRAM2M-SDRAM

    Monitor Block diagram

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    11/79

    LG Electronics/DND QA G11/79

    MICOM

    EEPROMX2416P

    VIDEOSWITCH

    (M52758FP)

    AUDIO

    L

    RAUDIO AMP

    LA4282(L&R)

    5

    5

    RGBHV

    RGBHV 3

    H/V

    SOG

    COLOR DECODER

    (VPC3230D)

    DEINTERLACE(FLI2200)

    MEMORY

    (4M-BYTE)

    ENHANCER(FLI2220) COLOR CONTROL

    &VIDEO SWITCH

    (CXA2101Q)

    3Y,Pb,Pr(STB)3Y,Pb,Pr(MNT)

    A/D CONVERTER

    (CXA3516R) SCALER

    (JAG200)

    MEMORY (6M-BYTE)

    EPLD

    (GEN. CLAMP)

    Buffer

    (74F574 x 4)

    H

    V

    Clamp

    2H/V

    H

    H

    V

    2PLLH/CLK

    5

    H/V/CLK/HBLK/VBLK

    4

    H/V/DE/CLK

    DISP_EN

    5

    RGBHV

    3RGB

    3RGB

    5Y,U,V,H,V

    SoundProcessor(MSP3401G)

    2H/V

    MONOSTALE MULTIBIB.

    SOG_OUT CLAMP_AD

    PORT EXP

    (M62320X3)

    ROM(AT29C010)

    (74HCT373)

    YCbCr/

    YPbPr

    CVBS

    2

    YUV

    41P

    8

    4

    H/V/FIELD/LLC1

    MN-42PZ10 VSC(JAG200 & FLI2200) Block Diagram

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    12/79

    LG Electronics/DND QA G12/79

    TUNER.1

    1

    CXA2069Q

    A/V SWV, L/R

    V, L/R

    S-VHSY / C

    AUDIO

    MSP3401G

    Sound

    Processor

    2nd SiF

    L/R(tv)

    DVD/DTV

    (RCA JACK)

    VPC3230D(MAIN)

    VidoProessor

    Y,Cr,Cb (DVD)

    DVD_Y

    VPC3230D(SUB)

    Video

    Proessor

    MS81V04160FRAME

    MEMORY

    PCL / R

    Y,Pb,Pr(DTV)

    Y,Pb,Pr(DTV)

    RGB(PC)

    CVBS

    RGB

    M52758FPRGB/YUV

    S/W

    DCF

    RE

    WE

    RN-BA11(Tuner Receiver) Block - DiagramRN-BA11(Tuner Receiver) Block - Diagram Ro

    Lo

    Y/C 2

    MNT_OUT

    CVBS

    Y/C

    OPTION

    TUNER.2

    TV (M)

    TV (S)L/R(tv)

    Y/C

    M52756FPRGB/YUV

    S/W

    RGB (DTV)

    RGB(OSD)

    LGTV1001

    DRP

    CXA2119MS/W

    +

    YUV

    L/R

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    13/79

    LG Electronics/DND QA G13/79

    Connecting 25 Pin cable

    (when connecting 25 Pin cable,Connect external equipment to STB)

    Product back & monitor in/output sectio

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    14/79

    LG Electronics/DND QA G14/79

    Power BoardY-Drive (TOP)

    Y-Board

    VSC Board

    Y-Drive (Bottom)

    Z-Board

    Controller Board

    EMI Filter

    Connection diagram (back covers ope

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    15/79

    LG Electronics/DND QA G15/79

    BACK COVER

    POWER BOARDVSC BOARD EMI Filter

    Exploded view (Back Cover, VSC, EMI, Powe

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    16/79

    LG Electronics/DND QA G16/79

    PANEL

    Y-BOARD

    Z-BOARD

    CONTROLBOARD

    X-BOARD

    X-BOARD

    Y-Drive BOARD

    Y-Drive BOARD

    Exploded view (Module)

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    17/79

    LG Electronics/DND QA G17/79

    VSC Board(Front) EMI Filter

    Power Board Z- BoardY-Board Control Board(Back)Y-Drive Board (Top)

    Y-Drive Board

    Main PowerSwitch

    Parts (back covers open)

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    18/79

    LG Electronics/DND QA G18/79

    X-Board ( Right)X-Board ( Left )

    Control Board Z-BoardY-BoardY-Drive Board

    EMI Filter & VSC Board are separate

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    19/79

    LG Electronics/DND QA G19/79

    Power well power Board-Korean market Murata Power Board

    Power Board ( SMPS )

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    20/79

    LG Electronics/DND QA G20/79

    1. The 4/7 or 3/7 of screen is not displayed.

    1) Check the X B/D power connector.

    2) Check the connector between CTRL B/D and X B/D.

    3) Replace the X B/D.

    relations between screen and X B/D

    screen X B/D

    left 4/7 of screen Right X B/D

    right 3/7 of screen Left X B/D

    type

    i) screens left(4/7) ii) Screens right(3/7)

    Non-displaying part

    Displaying part

    . Screen defect diagnosis

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    21/79

    LG Electronics/DND QA G21/79

    2. No image by Data COF. (the case one Data COF is totally or partially not displayed included)

    1) It is mainly caused by related Data COF and X B/D connection error.

    2) Check the connector between that Data COF & X B/D.

    3) When Data COF has a defect, replace the related X B/D. examples of screen display type( beside the below, any out of 7 Data COF can be occurred. )

    partially displaying

    ok

    Non-image

    Setx pattern( GND ) to ANODE,

    y Pattern (resistance joint part ) to CATHOD,

    Test diode forward and backward.Measure resistance value.(10)

    x GNDyresistance

    Data COF IC test method

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    22/79

    LG Electronics/DND QA G22/79

    3. Data COF IC unit error

    1) As pictures below, this is caused by the clock error of Data COF IC2) With , , , check Data COF connector and replace the X B/D.

    3) With , , check the connector between CTRL B/D & X B/D and replace X B/D or CTRL B/D.

    Cases

    Two every-second IC error in one

    4 IC errors in one COF

    Data COF IC unit error in the whole X B/D

    Data COF IC unit error in the whole screen.

    One IC error in one COF

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    23/79

    LG Electronics/DND QA G23/79

    casePartial error or total error with One or more ICs

    defect.

    4. Regular vertical line with one or more Data COF IC

    1) Regular vertical line with one Data COF IC is mainly caused by X B/D output terminal buffers output error. When two Data COF ICs have regular

    vertical lines, it means the data transfer from Controller B/D to X B/D has an error.

    2) Check the related X B/D connector.3) Replace that X B/D or CTRL B/D

    screen X B/D

    left 4/7 of bottom screen Right X B/Dright 3/7 of bottom screen Left X B/D

    relation between screen & X B/D

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    24/79

    LG Electronics/DND QA G24/79

    5. The screen by Scan FFC is not displayed

    1) It is mainly caused by the bad connection between Scan FFC & Y B/D.

    2) Check the related connector between Scan COF & Y B/D.

    3) When Scan IC has a defect, replace the related Y DRV B/D.

    case 1/8 of the screen

    total or partial non- image

    SCAN IC check

    Set Vpp Pin to ANODE, GND pin to CATHOD and test diode forward and backward.

    OK

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    25/79

    LG Electronics/DND QA G25/79

    6. Regular vertical lines in the whole screen. (mainly in one specific color, regular line is flicking)

    1) This problem is related to CONTROL B/D.

    2) Replace CONTROL B/D

    case

    Regular vertical lines in the whole screen

    7. Vertical Data copy

    1) It possibly happens when scan wave does not form properly.

    2) Replace Y DRVB/D or Y SUS B/D

    case

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    26/79

    LG Electronics/DND QA G26/79

    8. One or more vertical lines in the screen.

    1) Irregular vertical line is not related to Controller B/D or X B/D.2) It is mainly caused by the followings open(or short).

    - Panel itself defect

    - DATA COF FPC attached to panel is open or short.- DATA COF attached to panel itself defect

    3) Replace module

    caseThere are several types.

    Several lines in area.

    It can be seen on the both side, right and left.

    The area is sometimes over .

    9. One or more horizontal lines in the screen.

    1) Irregular borizontal line is not related to Controller B/D or Y B/D.

    2) It is mainly caused by the followings open(or short).

    - Panel itself defect

    - SCAN FPC attached to panel is open or short.

    - SCAN IC attached to panel itself defect

    3) Replace Y DRV B/D

    case

    Not always like this.

    There can be several horizontal lines

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    27/79

    LG Electronics/DND QA G27/79

    10. Input signal pattern is displayed but the whole brightness of the screen is dark.

    1) It happens when Z B/D is not operating well.

    2) Check whether Z B/Ds power connector is plugged .

    3) Check whether the connector between Controller B/D & Z B/D is plugged.4) Replace Controller B/D or Z B/D.

    11. In full white pattern, foreign color is displayed or in full black pattern, mis-discharge

    is partially occurred.

    1) Check the slope of Y B/D set up, set down waveform.

    2) Check the slope of Z B/Ds ramp waveform

    3) Measure each B/Ds output waveform by over 200MHz oscilloscope and compare it to the below picture.

    it is possible to control Y B/Ds setup slope by adjustinng VR2, setdown slope by VR1 and Z B/Ds ramp slope by VR1..

    - Y B/D measurement point : TP ( Connector P4 36 pin )

    - Z B/D measurement point : panel connection part ( SUS_OUT )

    setup

    setdown230 s

    25 s

    230V

    Vsetup

    175V

    Vs

    Y output voltage wave

    175V

    Vs

    15 s

    20 s

    Z RAMP voltage wave

    0V

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    28/79

    LG Electronics/DND QA G28/79

    13. A specific brightness of one color is not clear.

    1) Check CTRL B/Ds input signal connector.

    2) Replace CTRL B/D.

    12. In full white pattern, the brightness is getting darker toward the center.

    1) It happens with Z B/Ds ramp waveform

    2) Check the connection between CTRL B/D and Z B/Ds connection cable.3) Replace Z B/D.

    case

    i f di i

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    29/79

    LG Electronics/DND QA G29/79

    Non- image or same symptom when power off or black pattern. 1) Check CTRL B/Ds LED(D1~D4).

    2) Check the power or signal cable input into CTRL B/D.

    3) Check X B/D, Y B/D and Z B/Ds power connector.

    4) Check the connector between CTRL B/D and X B/D, Y B/D, Z B/D respectively.5) Measure each X, Y, Z B/Ds output waveform with over 200MHz oscilloscope and compare it to the below picture to detect the defect

    and replace that.

    - Y B/D measurement point : TP ( Connector P4 36 pin )

    - Z B/D measurement point : panel connection part ( SUS_OUT )

    - X B/D measurement point : L1(RIGHT), L2(LEFT BOTTOM)

    < A: Y B/D output waveform - 1 FRAME >

    < B: Y B/D output waveform - 1 SF >

    1Frame(16.7ms)

    . Non-picture Defect diagnosis.

    5) Test scan(Y) IC.

    6) Test data(X) COF IC.

    7) Replace CTRL B/D.

    < B: Y B/D output waveform - 2 SF(non-Setup SF) >

    6)Test scan(Y) IC.

    7)Test data(X) COF IC

    8)Replace CTRL B/D.

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    30/79

    LG Electronics/DND QA G30/79

    < B: Y B/D output waveform - 7~12 SF(SE) >

    < B: Z B/D output waveform - 1SF >

    < A: Z B/D output waveform - 1Frame >

    < A: Y B/D output waveform - 1Frame >

    < X B/D output waveform - 1 FRAME >

    < X B/D output waveform - amplification >

    < X B/D output waveform - 1 SF >

    O P i t S i G id

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    31/79

    LG Electronics/DND QA G31/79

    P6

    P4

    Rework should

    be done

    Y-Driver Board

    Y-Board

    42 PDP Flicker and42 PDP Flicker and No Raster TroubleshootingNo Raster Troubleshooting GuideGuide

    cause : bad connection between

    Y-Board# 1, 2 drive board Connector pin

    . One Point Service Guide 42 Inch

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    32/79

    LG Electronics/DND QA G32/79

    amplified amplified

    : outside Leg: inside Leg

    P 6, P 4 both are the first pin, when

    wiring, it should be done as picture

    shown.

    (bend the wire to Y-Driver B/D not

    to Y-B/D . If not there can be noise)

    Dont be confused with Pin number

    Improved since Dec,2001.

    P 4

    P 6

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    33/79

    LG Electronics/DND QA G33/79

    ure not to misconnect the line.the picture precisely and then connect jump wire at the exact point

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    34/79

    LG Electronics/DND QA G34/79

    X CANVAS X CAVBAS

    Intermittent no-image/image error while watch

    he screen is intermittently disappeared . LED is greenscreen is distorted weiderly (happened 2 a day)

    normal

    cause : bad connection between Y-Board and #1,2 pin of

    Y-Drive Board Connector

    troubleshooting : connect bad linking between Y-Board & Y-Drive with jump wire (all 4parts)

    see working instruction(revised sinceDec,2001. 1)

    CANVASX

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    35/79

    LG Electronics/DND QA G35/79

    X CANVAS

    normal

    CANVASX

    No Power( in ST-BY mode, but no LED)

    Check the power supply & main power S/W on

    Check EMI board fuse (check the rated capacity )

    No Power

    Fuse 15 A

    Be sure to use rated fuse.

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    36/79

    LG Electronics/DND QA G36/79

    X CAVBAS

    normal

    CANVASX

    when Powers on, after 2 ~ 3 sec, its off( LED changing green into red )

    ECK : remove STB and operate monitor individually.check STB defect or Monitor defect )

    en using ANALOG STB, check STB onlyMN-42PZ10 only STB : RN-BA11

    move each Boards power supply connector and check the power is off.en the power is not off,replace the related board.

    No Raster

    N Pi

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    37/79

    LG Electronics/DND QA G37/79

    X CANVAS

    normal

    CANVASX

    no picture (LEDs green)

    e checkpoint : remove STB and operate monitor individually.heck whether STBs a defect or monitors one)

    No Picture

    th monitor defect, check VSC and then Controller Board.

    roubleshooting : replace VSC Board

    Add B ( H i t l B

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    38/79

    LG Electronics/DND QA G38/79

    X CANVAS

    normal

    CANVASX

    no image (LEDs green)

    ause : Y-Drive ( Bottom ) defect

    roubleshooting : Y-Drive (lower part) replacement

    Address Bar ( Horizontal Bar

    Y-Drive Board ( Bottom )

    This problem is shown in the bottom of screen,So it is caused by Y-Drive

    Address Bar ( Horizontal Bar

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    39/79

    LG Electronics/DND QA G39/79

    X CANVAS

    normal

    CANVASX

    no image (LEDs green)

    Address Bar ( Horizontal Bar

    Y-Drive Board ( Top )

    ause : Y-Drive Board (upper part) defect

    roubleshooting : Y-Drive Board replacement

    No Picture

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    40/79

    LG Electronics/DND QA G40/79

    X CANVAS

    normal

    CANVASX

    no image (LEDs green)

    PD501 Connector

    No Picture

    ause : PD-501 Connector contact point defect

    roubleshooting : PD-501 Connector replacement

    (with PD-501 Connector contact point defect,arious defect symptoms can be seen)

    High frequency noise (Bee soun

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    41/79

    LG Electronics/DND QA G41/79

    X CANVAS

    normal

    CANVASX

    normal picture with high frequency noise (bee)

    High frequency noise (Bee soun

    C8178 0.22uFelectrolyticcapacitorinsertion

    Open C8139right lead andthen wire R8164right lead

    Power (SMPS) Board

    1. C8178 0.22 /50V add2. Open C8139 right lead,

    and then connect it toR8164 right lead.

    Improved since Nov,2001

    SMPS is supposed to operatewith high frequency sosmall noise is not consideredas a defect.

    light noise is not a defect and write down explanation

    No picture in right 2/5 are

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    42/79

    LG Electronics/DND QA G42/79

    X CANVAS

    normal

    CANVASX

    No picture in right- 2/5 are

    No picture in the right- 2/5 area

    X-Board ( Left ) power supply check

    X-Board ( Left )Connector check

    X-Board ( Left ) replacement

    Address Bar (Vertical )

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    43/79

    LG Electronics/DND QA G43/79

    X CANVAS

    normal

    CANVASX

    Address Bar (Vertical )

    stripe in right-2/5 area

    X-Board ( Left ) power supply check

    X-Board ( Left ) Connector check

    X-Board ( Left ) replacement

    No picture in left 3/5 of the scree

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    44/79

    LG Electronics/DND QA G44/79

    X CANVAS

    normal

    CANVASX

    X-Board ( Right ) power supply check

    X-Board ( Right )Connector check

    X-Board ( Right ) replacement

    left 3/5 of screen with vertical stripes

    No picture in left 3/5 of the scree

    Address Bar (Vertical )

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    45/79

    LG Electronics/DND QA G45/79

    X CANVAS

    normal

    CANVASX

    X-Board ( Right ) power supply check

    X-Board ( Right )Connector check

    X-Board ( Right ) replacement

    Address Bar (Vertical )

    left 3/5 of screen with vertical stripes.

    No Red

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    46/79

    LG Electronics/DND QA G46/79

    X CANVAS

    normal

    CANVASX

    no Red ( B or G )

    Be sure not to bend it by force or internInsulated conductor can be down.

    est Monitor individually.

    detect a problem with monitor, check VSC Board.it has a problem with STB connecting, focus on 25 Pin.

    e sure not to connect 5 Pin (AP-EA10) by force

    25 Pin Cable P/No : GVZ AP-EA10

    No Red

    1) X - Board COF Connector separation

    42 Inch

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    47/79

    LG Electronics/DND QA G47/79

    Lift up the right and left of X-BOARD CONNECTOR. Lift up X-BOARD CONNECTOR and separate

    COP CONNECTOR by pulling up.

    When you handle COF CONNECTOR, dont pressure. First release LOCK and separate.

    If COF CONNECTOR is damaged, you should replace MODULE ASSY. So, be aware of this!!

    1) X Board COF Connector separation

    When you exchange X-Board, first you should separate COFConnector. Be careful to handle it.COF Connector is attached to Module. When COF Connector isbroken, Module ASSY must be replaced a new one.

    When you exchange X-Board, first you should separate COFConnector. Be careful to handle it.COF Connector is attached to Module. When COF Connector isbroken, Module ASSY must be replaced a new one.

    WarningWarning

    COF Connector

    42 Inch

    2) X - Board Connector separation

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    48/79

    LG Electronics/DND QA G48/79

    Lift up each edge of left/right. Lifted condition

    2) X Board Connector separation

    Its easy to separate it by releasing Connector Lock .

    Do not pressure or it can be hurt.

    When LOCK is hurt, replace a new X-BOARD

    WarningWarning

    Be careful to handle LOCK or it can be broken.

    When LOCK is broken, replace a new X-BOARD.

    3) Y - Board COF Connector separation

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    49/79

    LG Electronics/DND QA G49/79

    Pull the white LOCK as shown in arrow

    Pull the white LOCK as shown in arrow.

    Separate COF CONNECTOR by pulling in the left.

    3) Y Board COF Connector separation

    WarningWarning

    Be careful to handle LOCK and COF Connector. When LOCK part is damaged, you should replace

    a new Y-Board. In case of COF Connector, Module Assembly.

    4) Z - Board COF Connector separation

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    50/79

    LG Electronics/DND QA G50/79

    4) Z Board COF Connector separation

    Separate the fixed Screw of Z-Board.

    Pull out Lock as shown in arrow.

    Condition in Lock part is pulled Pull COF Connector as shown in arrow.

    Its easy to separate COF on condition

    that Z-Board Screw is separated.

    In case Z-Board is assembled, its really

    hard to separate.Be careful not to tear COF Connector.

    If COF Connector is torn, replace a new Module Assembly

    WarningWarningCOF Connector

    ) Connector separation Guide

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    51/79

    LG Electronics/DND QA G51/79

    Push LOCK and pull out

    PUSH PUSHPUSH

    ) Connector separation Guide

    PUSH PUSH PULL

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    52/79

    7) Gas injection (Sealing up) condition

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    53/79

    LG Electronics/DND QA G53/79

    Be sealed up after gas injection

    Be careful to handle the sealed-up part after gas injection.

    If it is broken, the gas escapes. So, replace the Module.

    ) j ( g p)

    WarningWarning

    Be sealed up after gas injection

    8) Power off in 2 ~ 3 minutes(Protection)

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    54/79

    LG Electronics/DND QA G54/79

    Power is On and off 2~3 minutes.

    (Protection)

    Power is On and off 2~3 minutes.

    (Protection)

    P301 Connector Open Check.P301 Connector Open Check. X - Board Top Right Change.X - Board Top Right Change.

    P302 Connector Open CheckP302 Connector Open Check X - Board Top Left Change.X - Board Top Left Change.

    P303 Connector Open CheckP303 Connector Open Check

    P304 Connector Open CheckP304 Connector Open Check

    P102 Connector Open CheckP102 Connector Open Check

    X - Board Bottom Right Change.X - Board Bottom Right Change.

    X - Board Bottom Left Change.X - Board Bottom Left Change.

    Z - Board Change.Z - Board Change.

    P3, P2 Connector Open CheckP3, P2 Connector Open Check Y - Board Change.Y - Board Change.

    P005, P003 Connector Open CheckP005, P003 Connector Open Check

    P006 Connector Open CheckP006 Connector Open Check

    VSC- Board Change.VSC- Board Change.

    VSC - Board Change.

    Sound Output IC Short Check

    VSC - Board Change.

    Sound Output IC Short Check

    Power Board ChangePower Board Change

    OK

    OK

    OK

    OK

    OK

    OK

    OK

    OKPROTECT operation;

    When the load voltage is short.

    When each voltage doesnt work (in general)

    PROTECT operation;

    When the load voltage is short.

    When each voltage doesnt work (in general)

    ) ( )

    9) Power off in 2 ~ 3 minutes(Protection)

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    55/79

    LG Electronics/DND QA G55/79

    L813 Cold Solder

    CheckCheck

    Open the Connector connecting to each Board to check the power is off.

    if each Board is same, check the Power Board and voltage.

    Symptom : As soon as the power on,

    its off in 2 - 3minutes.

    (PROTECT operation)

    Cause : No VS voltage

    L813 Coil cold soldering.

    10) ADD BAR inspection and repair

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    56/79

    LG Electronics/DND QA G56/79

    MP-40PA10 uses 4 board such as left,right, top and bottom.

    Divide the screen in 4 and once you see ADD BAR check COF CONNECTOR

    between MODULE and X-BOARD.

    If there is no defect in COF CONNECTOR replace X-BOARD.

    But the problem still remains and check the connector between X-BOARD and

    CONTROL BOARD. And if you cant find defect, check CONTROL.

    HEATRUN : WHITE

    Press the ADJ KEY and check the position of add bar by changing WHITE or

    RED or BLUE or GREEN

    Top Right Top Left

    Bottom Right Bottom Left

    11) One Point Service Guide

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    57/79

    LG Electronics/DND QA G57/79

    Symptom : B color 1 Address line Open

    Cause : Dented COF

    COF is dented

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    58/79

    LG Electronics/DND QA G58/79

    Symptom : Inferior R Address color

    Cause : InferiorDATA output bycold soldering16 pin of IC14 in X-L-TOP

    ( Normal waveform after tearing off IC Pin)

    Countermeasure : Replace X-L-TOP board.

    IC14

    Cold Soldering

    Abnormal waveform by cold soldering

    Normal waveform after tearing off IC pin

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    59/79

    LG Electronics/DND QA G59/79

    CheckCheck

    The blue spreads on the screen (Mis-discharge)

    and power off in 2 ~ 3 seconds.

    If you turn on again, it will be same problem.

    Symptom Causes Countermeasure

    If 15V line voltage reduces

    below 14V,Mis-discharge occurs and

    power off because of

    protection circuit.

    Replace PSU

    (Power Supply Unit)and defective X-Board.

    If when Power on, screen shows like above and turn off in 2 seconds, check if turning off or not by disconnecting

    all X & Y boards.

    Defective X-Board

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    60/79

    LG Electronics/DND QA G60/79

    CheckCheck

    The top left part of screen is broken

    (Top Right X-BOARD)

    Symptom Cause Countermeasure

    No 5V supply to Top rightX-Board.

    Connect 5V line

    Check Top right X-BOARD 5V.(If 0V, it happens)

    Check 5V line from SMPS to X-BOARD.

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    61/79

    LG Electronics/DND QA G61/79

    CheckCheck

    Pinkish screen in the top left.

    (Top right X-BOARD)

    Symptom Cause Countermeasure

    No Va(70V) supply to Topright X-Board.

    Connect 70V line

    Check Top right X-BOARD Va(70V).(If 0V, it happens)

    Check 70V(Va) line from SMPS to X-BOARD.

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    62/79

    LG Electronics/DND QA G62/79

    CheckCheck

    The 3/5 top left in the screen is blank

    (Top Right X-BOARD)

    Symptom Cause Countermeasure

    Check Top right X-BOARD 12V.( If 0V, it happens )

    Check Top right X-BOARD Va(70V).(If 0V, it happens)

    Check 12V & 70V(Va) line from SMPS to X-BOARD.

    No 12V supply to Top rightX-Board.

    No Va(70V) supply to Top

    right X-Board.

    Connect 12V line

    Connect 70V line

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    63/79

    LG Electronics/DND QA G63/79

    CheckCheck

    The 3/5 top right of the screen is blank.

    (Top left X-BOARD)

    Symptom Cause Countermeasure

    No 12V supply to Top leftX-Board.

    No Va(70V) supply to Top

    left X-Board.

    Connect 12V line

    Connect 70V line

    Check Top left X-BOARD 12V.( If 0V, it happens )

    Check Top left X-BOARD Va(70V).(If 0V, it happens)

    Check 12V & Va(70V) line from SMPS to X-BOARD.

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    64/79

    LG Electronics/DND QA G64/79

    CheckCheck

    Pinkish screen in the 1/5 top right

    (Top left X-BOARD)

    P1 COF connector on Top leftX-Board is open.

    Reassemble it

    Check the contact point and Locking of P1 on Top left X-BOARD.

    Symptom Cause Countermeasure

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    65/79

    LG Electronics/DND QA G65/79

    CheckCheck

    The 3/5 bottom left of screen is broken.

    (BOTTOM RIGHT X-BOARD)

    Symptom Cause Countermeasure

    No 5V supply to bottom rightX-Board.

    Connect 5V line

    Check Bottom right X-BOARD 5V.( If 0V, it happens )

    Check 5V line from SMPS to X-BOARD.

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    66/79

    LG Electronics/DND QA G66/79

    CheckCheck

    The 3/5 bottom left of the screen is Blank.

    (Bottom Right X-BOARD)

    Symptom Cause Countermeasure

    Check Bottom right X-BOARD 12V.( If 0V, it happens )

    Check 12V line from SMPS to X-BOARD.

    No 12V supply to bottom rightX-Board.

    No Va(70V) supply to bottom

    right X-Board.

    Connect 12V line

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    67/79

    LG Electronics/DND QA G67/79

    CheckCheck

    The 2/5 right of the screen is broken.

    (Bottom left X-BOARD)

    Symptom Cause Countermeasure

    Check Bottom left X-BOARD 5V.( If 0V, it happens )

    Check 5V line from SMPS to X-BOARD.

    No 5V supply to bottom leftX-Board.

    Connect 5V line

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    68/79

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    69/79

    LG Electronics/DND QA G69/79

    CheckCheck

    ADDRESS bar appears in the right bottom of the screen.

    (X-BOARD BOTTOM LEFT)

    The connecting of X-Board bottomleft connector is bad. Reassemble it.

    Check connecting of the connector of bottom left X-BOARD.

    Reassemble it.

    X-BOARD BOTTOM LEFT CONNECTOR

    OPEN.

    Symptom Cause Countermeasure

    Examples

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    70/79

    LG Electronics/DND QA G70/79

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    71/79

    LG Electronics/DND QA G71/79

    CheckCheck

    Screen is divided in top and bottom, and vertical bar

    appears.

    Connector(P13) is OPEN orConnecting condition is bad Reassemble P13.

    P13 CONNECTOR contact point inferior CHECK.

    P13 CONNECTOR SIGNAL CHEK.

    P13 CONNECTOR

    Symptom Cause Countermeasure

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    72/79

    LG Electronics/DND QA G72/79

    CheckCheck

    Screen is broken and has the vertical/horizontal bar.

    VSC Board Connector is Open. Reassemble VSC BoardConnector

    Check the connector connecting

    Reassemble the Connector

    Symptom Cause Countermeasure

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    73/79

    LG Electronics/DND QA G73/79

    CheckCheck

    The screen is bluish(Mosaic screen)

    Loose VSC Board Connector Reassemble VSC BOARD

    Connector

    Check the connection condition of the Connector.

    Reassemble the Connector.

    Symptom Cause Countermeasure

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    74/79

    LG Electronics/DND QA G74/79

    CheckCheck

    The mosaic appears in the screen when it connects to VIDEO Input.

    (The sensibility of Y-signal is low.)

    When connected to Component Input, it is O.K.

    Bad IC203 Replace IC203(VPC3230D)

    Check if X201 on VSC board oscillates.

    Check Video In/Out of IC203 on VSC board.

    IC201

    (VPC3230D)

    Decoder IC

    Symptom Cause Countermeasure

    Examples

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    75/79

    LG Electronics/DND QA G75/79

    IC201(VPC3230D) Decoder is inferior

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    76/79

    LG Electronics/DND QA G76/79

    CheckCheck

    Noise with division of colors

    Bad Connector connecting

    Control Board and VSC B/D.

    Contact point and signal condition of Connector Control Board and VSC Board.

    Abnormal Normal

    Bad Connector

    SymptomCause

    Countermeasure

    Change the Connector

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    77/79

    LG Electronics/DND QA G77/79

    Name No signal Vertical Bar

    Symptom Cause and Countermeasure

    Realization

    1.Cause : Bad IC2 (DA1)

    8cm

    When ASIC Chip(IC2 DA1 LGD4001) on Control Board gets

    high temperature, you can observe it

    (In normal temperature its O.K. )

    IC2 DA1(Data Arrange) No.162 Pin output is changingdepending on the temperature. abnormal X-Bd Buffer IC

    * Room temperature : 2.5V Output (Normal Pin = over 2.8V)

    * Heated : 1.5V Output(Normal Pin = 2.7V )

    Bad IC2 (DA1)

    < Waveform of normal pin>

    heated

    < Waveform of abnormal pin >

    heated

    DA1

    Buffer

    DA1

    Buffer

    Buffer(74ACT541) waveform abnormally narrows.

    In this case, it is impossible for Flip Flop(74AC574) on X

    B/D to read data.

    2. Countermeasure : Replace IC2

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    78/79

    LG Electronics/DND QA G78/79

    Name Add Open (Green 1 Line)

    Symptom Cause and Countermeasure

    1.cause: Add. COF Drive IC inferior

    Normal Line Data waveform Open Line Data output waveform

    the output of inferior line less than that of the normal LineAdd. COF Drive IC inferior

    COF inspection : 24V Open check (normal 50V)

    Add. COF Drive IC

  • 8/7/2019 lg_42_inch_plasma_tv_training_manual_[ET]

    79/79

    Name Vertical bar when Power off/on(Mis-discharge)

    Symptom Cause and Countermeasure

    Realization

    1.PDP Power on Mode external input

    (regardless of wire/wireless signal but its easy to reenact in wireless

    signal)

    2. Remove Power Cord (Powers off)

    3.after about 20minutes, insert Power cord

    (automatically the Powers on and the vertical bar is shown as above)

    1.Cause : Control board malfunctions when Power off/on.

    2.Countermeasure: Change some parts on Control board.

    3.Changing parts : A32_CTRL_03 B/D (Marked on PCB)

    -.R14,17,18,21 : 330 ==> 4.7K (Chip Resistor)

    -.R15,16,19,20 : 22K ==> 4.7K (Chip Resistor)

    -.C504, 505 : 0.1uF / 50V add (Chip Capacitor)

    Control board