lexus rx 450h 2010– tvip v2 preparation glass · pdf filelexus rx 450h 2010– tvip...

LEXUS RX 450h 2010– TVIP V2PREPARATION GLASS BREAKAGE SENSOR (GBS)

of 19Issue B : 05/28/09

Part #: PT398-48090 NOTE: Part number of this accessory may not be the same as the part number shown.

Conflicts: Do not install into Vehicles without Factory Alarm System.

RecommendedToolsPersonal&VehicleProtection Description

Safety Glasses

Safety Gloves (Optional)

Vehicle Protection Blankets, Parts Boxes

SpecialTools

InstallationToolsScrewdriver #2 Phillips, Flat Blade Jeweler’s

Nylon Panel Removal Tool e.g. Panel Pry Tool #1 Toyota SST# 00002-06001-01

Side Cutters

Torque Wrench 36 in•lbf (4.07 N•m), 88.5 in•lbf (10 N•m)

Tape Clear, Electrical

Socket 8mm, 10mm, extension

SpecialChemicalsCleaner VDC Approved Cleaner

Glass Cleaner Household Glass Cleaner

KitContents

AdditionalItems(may be required)

Item# Description

RecommendedSequence ofApplicationItem# Description

x1 x1 x5x1 x1 x1

x1 English x2

GBS ECU GBS Harness Wire Tie

Window Label Owner’s Guide

GBS ECU Bracket GBS Microphone Foam Tape M5 Screw

x2

Spanish x2


of 19Issue B : 05/28/09

LegendDo not proceed until process has been completed.

Follow steps carefully to avoid damaging the Vehicle or AccessoryUse caution to avoid injury.

Used in Figures to call attention to specific tools recommended for the process.

Highlights a change in installation with respect to previous issue.

Indicates that torque is related to safety.

AccessoryInstallationPractice(readbeforeinstallation)Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation.These guidelines can be found in the “Accessory Installation Practices” document.This document covers such items as:

Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.)• Safety (eye protection, checking torque procedure, etc.)• Vehicle Disassembly/Reassembly (panel removal, part storage, etc.)• Electrical Component Disassembly/Reassembly (battery disconnection, • connector removal, etc.)

Please see your Lexus dealer for a copy of this document.

TableofContentsPreparationI. ............................................................................................................................ 1 – 4

Table of Contents1. ................................................................................................................................................2Wire Routing Overview2. .......................................................................................................................................3Disassembly Overview 3. .......................................................................................................................................4

ProcedureII. ............................................................................................................................5 – 1 6Disassembly (Luggage Compartment)1. ...............................................................................................................5Disassembly (Passenger’s Side)2. ........................................................................................................................6GBS ECU and V2 Harness Installation3. ............................................................................................................. 11GBS Microphone Installation4. ............................................................................................................................14Complete the Installation.5. .................................................................................................................................15

Check ListIII. ............................................................................................................................ 17-19Accessory Function Checks.1. .............................................................................................................................17Vehicle Function Checks2. ...................................................................................................................................18


of 19Issue B : 05/28/09

TVIP

Vehi

cle

Des

crip

tion

A–

8P W

hite

(fo

r GB

S E

CU

)B

–G

BS

EC

UC

eF2

8P W

hite

D–

2P W

hite

Mal

e (fo

r GB

S M

ic)

E–

2P W

hite

Fem

ale

(for G

BS

Mic

)F

–G

BS

Mic

WireHarnessOutline(Passenger’sCompartment)

A

B

C

DEF


of 19Issue B : 05/28/09

13 3

6 Glovebox Side Trim

7 Seat Temperature Control Unit

8 Shift Knob

9 Center Console

10 Center Console Side Trim

1 Spare Tire Cover

2 Battery Cover

3 PS Step Cover

4 PS Cowl Cover

5 Glovebox Under Cover

11 PS Knee Airbag

12 Glovebox

13 Engine Cover

14 Fuse Box Cover

Disconnect all Corresponding Connectors.

2

13

3

4

5

6

7

10

11

12

8

DisassemblyOverview

14

1

9

LEXUS RX 450h 2010– TVIP V2PROCEDURE GLASS BREAKAGE SENSOR (GBS)

of 19Issue B : 05/28/09

Remove Battery Cover.c. Press then remove 3 Clips.•

Disconnect the Negative d. Battery Terminal.

Note the Battery Cable Position as it • will be re-installed in the same position.

CAUTION:Do not touch the Positive Terminal.

1. Disassembly (LuggageCompartment)

Place the Vehicle in Park with the a. Parking Brake set.Remove Spare Tire Cover.b.

Nylon Panel Removal Tool, 10mm Socket


of 19Issue B : 05/28/09

Disassembly(Passenger’sSide)2. Remove Passenger’s Side Step Covera.

Remove Passenger’s Side b. Cowl Cover

Remove Glove Box Under c. Cover.

Nylon Panel Removal Tool


of 19Issue B : 05/28/09

Remove Glove Box Side d. Trim.

Remove Seat Temperature e. Control Unit.

Nylon Panel Removal Tool


of 19Issue B : 05/28/09

Remove Shift knob by turning f. counter-clockwise.

Push Shift Release with g. taped screwdriver and shift to Neutral.

Pull on the Left side Stick h. Shift Cover, then pull the Center Cover up and pull on the Right side Stick Shift Cover.

Shift Center Console to the i. left and place protective blankets.Remove the Center Console j. Side Trim.

Screwdriver,Electrical Tape


of 19Issue B : 05/28/09

Remove 3 Bolts.k.

10mm Socket, Extension

Remove Airbag carefully l. then wrap it and stack on any object to lift it high enough to prevent ten-sion on the Airbag wire.


of 19Issue B : 05/28/09

Remove 3 Screws at the m. bottom of the Glovebox.Open Glovebox and n. remove 2 Screws.

Remove the Glovebox by o. pulling it towards the left side.

Phillips Screwdriver


of 19Issue B : 05/28/09

Place GBS into posion for installation.

8mm Socket, Flat Blade Jeweler’s Screwdriver

GBSECUandV2HarnessInstallation3. Adjust the GBS sensitivity value to “9.” a. Navigate GBS ECU into place and install using 2 Bolts.b.

12

3

45 7

8

9

1011

6

12

3

45 7

8

910

11

6


of 19Issue B : 05/28/09

Connect the V2 Harness to c. the GBS ECU. Route the V2 Harness behind d. the Passenger’s Reinforce.

Plug the V2 Harness to the e. Vehicle’s Pre-Connector in the location shown.


of 19Issue B : 05/28/09

Route the V2 Harness along f. the Vehicle Harness and secure with 3 Wire Ties.

Side Cutters


of 19Issue B : 05/28/09

GBSMicrophoneInstallation.4. Lift protective padding from the Glovebox a. Under Cover.Using VDC approved Cleaner and Cleaning b. Method clean the area indicated on the Glove Under Cover.Remove the Protective Backing from the V2 c. Microphone.

CAUTION:Do not touch the Adhesive Surface.Attach the GBS Microphone on the Glovebox d. Under Cover as shown.• Make sure to align the GBS Mic to the edge of the

Glovebox Hole.

Use 1 Foam Tape to secure the GBS e. Microphone.

CAUTION: Do not cover the Microphone Opening with the Foam Tape.

Plug the 2P Connectors.f.

Install the Glovebox Under Cover.g.


of 19Issue B : 05/28/09

HOW TO

ALIGN TO

THE ETCH

ING

10 mm

1–5 mm

Clear Tape Fig. 5-2

HOW TO

ALIGN TO

OTHER LABELS

CompletetheInstallation.5. Position the Negative Battery a. Cable at the original factory position.

Tighten the Nut to 36 in•lbf • (4.07 N•m)

CAUTION: Do not touch the Positive Terminal.

Use Household Glass b. Cleaner to clean the inside of the Front Door Windows.Use a piece of Clear Tape c. to lift the Label from its protective backing.

CAUTION:Do not touch the adhesive surface.

Attach the Label as shown.d.

NOTE: Make sure to Align according to Etching or Other Label.

REPEAT: steps b–d with the other Window.

Verify that the Short Pin is e. Installed.

If not Install now.•

Fig. 5-3


of 19Issue B : 05/28/09

Reassemble the Vehicle.f.

NOTE: When reinstalling Knee Airbag, make sure to tighten the Bolts to 88.5 in•lbf (10 N•m).

VERIFY: That panels fit together properly, with no uneven gaps.

VERIFY:That all Connectors are plugged in.

Clean up and Remove trash.g. Sealed in its protective bag, h. place the Owner’s Manual in the Glovebox.Reset the power windows.i.

Turn the ignition “ON.”•

Lower the Windows halfway.•

Pull up on the Power Window • Switches until the windows close.

Continue to hold up on the • switches for a minimum of 1 Second.

Reset the Moon Roof.j. Open the Moon Roof halfway.•

Push and hold the Moon Roof • Switch to close until the Moon Roof closes.

Continue to hold the switch for a • minimum of 1 Second.

Reset the tailgate door.k. Push door lock control switch to • the “unlock” side.

Pull up tailgate door handle. •

LEXUS RX 450h 2010– TVIP V2CHECKLIST – these points MUST be checked to ensure a quality installation. GLASS BREAKAGE SENSOR (GBS)

of 19Issue B : 05/28/09

AccessoryFunctionChecks

Roll up all windows, and exit the vehicle with remote.

TakeouttheSmartKeyandtheSmartCardKeyfromtheVehicle.Placethem7ft.(2meters)ormoreawayfromtheVehicle.

1 Press and release the remote control lock button to start the system’s arming process.

The turn signal lights flash once

All doors lock.

The Security LED lights up.

2 Wait 30 seconds. Security LED starts flashing; the system is now armed.

Perform the following check in a temperature controlled environment (50°-90° F)

3 With the tip of a key, or Striker Tool pulled all the way out (PPO only), tap the center of the driver’s door window to trigger the alarm.

The horn sounds repeatedly.

The headlights flash repeatedly.

The turn signal lights flash repeatedly.

The security LED lights up.

4 Insert the key into the driver’s door key cylinder and turn it toward the back of the vehicle to stop the alarm.

The horn stops sounding.

All the lights stop flashing and/ or turn off.

The Security LED turns off.

NOTE: If the alarm does not trigger during functional verifications the Smart Key and Smart Card Key might be too close.Move them farther from the vehicle and test the system again.

NOTE: If the alarm does not trigger during functional verifications, increase the GBS sensitivity to the next setting and test again.

NOTE: If you do not disarm the system, the alarm will last 20 seconds. It is not necessary to check the alarm duration.


of 19Issue B : 05/28/09

VehicleFunctionCheck

Function Function

□ Head Light □ ABS Light (if equipped) If the warning light remains on, it may indicate a system malfunction.

□ High Beams □ Rear Wiper/Washer (if equipped)

□ Turn Signal Lights □ Clock (if equipped)

□ Tail Lights □ Accessory Power Socket (if equipped)

□ Stop Lights □ Starter

□ Backup Lights □ Audio/Video (if equipped)

□ Hazard Lights □ Power Sliding Door (if equipped)

□ Marker Lights □ Convenience Memory Settings (if equipped)

□ Dome/Courtesy Lights □ Heated Seats (if equipped)

□ Panel/Switch Illumination □ Massage Seats (if equipped)

□ Accessory Controls/Illumination (if equipped)

□ Rear Window Defogger (if equipped)

□ Key Sensor Buzzer □ Power Side Mirrors (if equipped)

□ Fog Lights (if equipped) □ Side Mirror Defogger (if equipped)

□ Daytime Running Lights (if equipped) □ Front Windshield Defogger (if equipped)

□ Trunk/Tailgate/Bed Lights (if equipped) □ Navigation System (if equipped)

□ Glove Box Light (if equipped) □ Rear Sunshade (if equipped)

□ Cruise Control Light (if equipped) □ Steering Wheel Audio Control (if equipped)

□ Seat Belt Warning Light If the warning light remains on, it may indi-cate a system malfunction.

□ Steering Wheel Column Adjusts Without Interference


of 19Issue B : 05/28/09

Function Function

□ Air Bag Warning Light If the warning light remains on, it may indicate a system malfunction.

□ Lamp Failure Sensor If the warning light remains on, it may indicate a sys-tem malfunction.

□ Track/Skid Control Light (if equipped) If the warning light remains on, it may indicate a system malfunction.

□ Front Wiper/Washer

□ HVAC □ Hood Latch Release

□ Power Locks (if equipped) □ Passenger Air Bag Switch (if equipped)

□ Power Windows (if equipped) □ Rollover Side Curtain Air Bag Switch (RSCA) (if equipped)

□ Power Seats (if equipped) □ Tire Pressure Monitoring System (TPMS).

Prior to TPMS activation and Pre-delivery Service (PDS) of the Vehicle the TPMS light will blink when IG is turned on.

After TPMS activation and PDS of the Vehicle the TPMS light will illuminate for a few seconds and go off when IG is turned on.

□ Horn

□ Gauges

RemovetheshortpinafterFunctioncheck. Check with your Port/Dealer to see if this step is necessary.

lexus rx 450h 2010– tvip v2 preparation glass · pdf filelexus rx 450h 2010– tvip...

Documents