lenel systems international inc. -...
TRANSCRIPT
Lenel Systems International Inc.HARDWARE PRODUCTS CATALOG
PERPETUAL INNOVATION
Acc
ess
Con
trol
Vide
oC
rede
ntia
l
ContentsAccess Control Hardware
Controllers & Interfaces Intelligent System Controllers
Intelligent Dual Reader Controller
Reader Interface Modules
Input/Output Control Modules
Reader Interface Gateways
Star Multiplexer
Readers & Keypads Magnetic Card Access Readers
Proximity Card Readers
OpenCard™ & OpenProx™ Readers
Biometric Reader
Indestructible Keypads & Readers
Command Keypad
Power Supplies and Enclosures Multi-Agency Power Supply/Chargers
CE-Marked Power Supply/Chargers
Identity Credential Hardware
Capture Hardware USB Capture Kit
Digital Video Hardware
Video Recorders Video Recorders for OnGuard VideoManager™
Network Video Cameras Fixed Network Cameras
Speed Dome Network Cameras
Video Encoders Single Channel Video Encoder
Contact Information
Page
1
9
11
15
19
23
25
27
33
36
39
43
45
47
49
51
53
57
61
64
Manage Everything...
Access C
ontrol
LNL-500
The LNL-500 Intelligent System Controller (ISC) by Lenel serves as the access control engine for
an OnGuard system. The ISC provides power, performance, and flexibility for the most demanding
applications. Multiple combinations of Input Control Modules, Output Control Modules, and Card
Reader Interface Modules can be connected.
The ISC can communicate upstream at 38.4 Kbps via RS-232/RS-485 multidropped configuration,
modem dial-up communication, or Ethernet TCP/IP networks. The ISC can store up to 12,500
cardholders. The ISC can have two downstream 2-wire RS-485 channels or one 4-wire RS-485
channel. In either configuration, you may connect up to 32 readers or 16 devices. Each device
(LNL-1100, LNL-1200, LNL-1300,LNL-1320) uses one device address.
Features and Functionality
■ Host communications - 38.4 Kbps direct wire (RS-232/RS-485 multidropped), Ethernet TCP/IP,
or dial-up communication
■ 12 VAC or 12 VDC input power
■ Supports up to 8 different card formats simultaneously
■ Enhanced anti-passback capabilities
■ Flash memory for real-time program updates
■ Lithium battery back-up
■ Up to 32,000 access levels
■ 255 holidays with grouping
■ 255 timezones, each with 6 time intervals
■ Elevator control, support for 64 floors
■ 512 KB on-board memory (Up to 12,500 cardholders)
■ Up to 16 downstream devices and 32 readers
■ Alarm masking
■ Individual extended held open and strike times (ADA required)
■ Up to 9-digit PIN codes
■ Biometric smart card template storage support
■ Status LEDs for heartbeat, upstream and downstream communication
■ 2 dedicated inputs for tamper and power failure status
■ NIST certified Advanced Encryption Standard (AES) 128-bit communication algorithm
Intelligent System Controller
1
Acc
ess
Con
trol
LNL-500
2
Controller OptionsLNL-500Host Communications
LNL-ETHLAN-MICR
Dial-Up ModemLNL-56KEXTLNL-DC336K
Power Supplies & EnclosuresLNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
SpecificationsPrimary Power (DC or AC)
DC input:AC input:
Memory and Clock BackupEnvironmental
Temperature:
Humidity:Mechanical
Dimensions:Weight:
Approvals
Standard 512 KB on-board memory
CoBox Micro serial server, flash ROM, RJ-45 (10/100Base-T), diagnostic LEDs, dimensions 1.57 x 1.93 in. (39 x 49 mm), internally powered, standoffs included
56 K external modem with cables12 VDC-powered, 33.6 K external modem for Intelligent System Controller
Lenel UL Listed 4 A, 110 VAC Power Supply - 12 VDC or 24 VDC 4 A output (switch-selectable), 120 VAC input, continuous supply current with enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery optional), UL-listedLenel UL Listed Power Supply - 12 VDC or 24 VDC 6 A output (switch-selectable), 120 VAC (1.6 amps) input, continuous supply current with enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery optional), UL-listedBattery Kit - 12 VDC, 12 AH battery (PS-12120)
* The ISC is for use in low voltage, power-limited, class 2 circuits only.12 VDC ± 15%. 250 mA12 VAC ± 15%. 400 mA RMS3 V lithium, type BR2325
Operating: 32° to 158° F ( 0° to +70° C)Storage: -67° to 185° F (-55° to +85° C)0 to 95% RHNC
6 x 5 x 1 in. (152 x 127 x 25 mm)8 oz. (230 g) nominalUL 294 and 1076-listed, CE-marked, RoHS compliantNIST certified Advanced Encryption Standard (AES) 128-bit communication algorithm
RS-485 multidrop
LNL-1300Up to 16 Single ReaderInterface Modules
LNL-1100Input Control Module
(Up to 16 Inputs perLNL-1100)
LNL-1200Output Control Module
(Up to 16 Outputs perLNL-1200)
LNL-1320Up to 16 Dual ReaderInterface Modules
Up to 16 Downstream Devices(32 Readers Max)
Downstream Communication
Two 2-wire ports orOne 4-wire port
LNL-500Intelligent System Controller
OnGuard Security Server
CORPORATE HEADQUARTERS LOCAL AREA NETWORK (TCP/IP)
Access C
ontrol
LNL-1000
The LNL-1000 Intelligent System Controller (ISC) by Lenel serves as the access control engine for
an OnGuard system. The ISC provides power, performance, and flexibility for the most demanding
applications. Multiple combinations of Input Control Modules, Output Control Modules, and Card
Reader Interface Modules can be attached.
The ISC can communicate upstream at 38.4 Kbps via RS-232/RS-485 multidropped
configurations, modem dial-up communication, or Ethernet TCP/IP networks. The ISC can store up
to 175,000 cardholders online. Each ISC can have four downstream 2-wire RS-485 channels or
two 4-wire RS-485 channels. In either configuration, up to 64 readers or 32 devices may be
connected to a single ISC. Each device (LNL-1100, LNL-1200, LNL-1300, or LNL-1320) uses one
device address.
Features and Functionality
■ Host communications - 38.4 Kbps direct wire (RS-232/485 multidropped), Ethernet TCP/IP,
or dial-up
■ 12 VAC or 12 VDC input power
■ Supports up to 16 different formats (8 card formats and 8 asset formats)
■ Enhanced anti-passback capabilities
■ Flash memory for real-time program updates
■ Lithium battery back-up
■ Up to 32,000 access levels
■ 255 holidays with grouping
■ 255 timezones, each with 6 time intervals
■ Elevator control, support for 64 floors
■ 1 MB on-board memory, expandable to 4 MB (up to 175,000 cardholders)
■ Up to 32 downstream devices and 64 readers
■ Alarm masking
■ Individual extended held open and strike times (ADA required)
■ Up to 9-digit PIN codes
■ Status LEDs for heartbeat, upstream and downstream communication
■ Two dedicated inputs for tamper and power failure status
■ Biometric credential-based device support
■ NIST certified Advanced Encryption Standard (AES) 128-bit communication algorithm
Intelligent System Controller
3
Acc
ess
Con
trol
LNL-1000
Controller OptionsLNL-1000Memory Options
LNL-1003MKHost Communications
LNL-ETHLAN
Dial-Up ModemLNL-56KEXTLNL-DC336K
SpecificationsPrimary Power (DC or AC)
DC input:AC input:
Memory and Clock BackupCommunication Ports
Port 1:Ports 2-5:
InputsCabinet Tamper Monitor:Power Fault Monitor:
Wire RequirementsPower:RS-485:RS-232:Inputs:
EnvironmentalTemperature:Humidity:
MechanicalDimensions:Weight:
Approvals
Standard 1 MB on-board memory
3 MB memory expansion kit (Includes 3 MB memory and expansion board)
Micro serial server, flash ROM, DB25 serial port RJ-45 (10/100Base-T)Ethernet interface, diagnostic LEDs, external power 120 VAC with cables
56 K external modem with cables12 VDC-powered/33.6 K external modem for Intelligent System Controller
* The ISC is for use in low voltage, power-limited, class 2 circuits only.12 VDC ± 15%. 350 mA12 VAC ± 15%. 600 mA RMS 3 V lithium, type BR2325
RS-232 or RS-485 (2-wire or 4-wire) 9600 to 38.4 Kbps asyncRS-485 (2-wire or 4-wire) 9600 to 38.4 Kbps async
Unsupervised, dedicatedUnsupervised, dedicated
1 twisted pair, 18 AWG24 AWG twisted pair(s) with shield, 4000 ft. (1219 m) maximum24 AWG, 25 ft. (7.6 m) maximumTwisted pair, 30 ohms maximum
Operating: 32° to 158° F (0° to +70° C) Storage: -67° to 185° F (-55° to +85° C)0 to 95% RHNC
6 x 8 x 1 in. (152 x 203 x 25 mm)10 oz. (290 g) nominalUL 294 and 1076-listed, CE-marked, RoHS compliantNIST certified Advanced Encryption Standard (AES) 128-bit communication algorithm
RS-485 multidrop
LNL-1300Up to 32 Single ReaderInterface Modules
LNL-1100Input Control Module
(Up to 16 Inputs perLNL-1100)
LNL-1200Output Control Module
(Up to 16 Outputs perLNL-1200)
LNL-1320Up to 32 Dual ReaderInterface Modules
Up to 32 Downstream Devices(64 Readers Max)
Downstream Communication
Four 2-wire ports orTwo 4-wire ports or
Combination 2- and 4-wire ports
LNL-1000Intelligent System Controller
OnGuard Security Server
CORPORATE HEADQUARTERS LOCAL AREA NETWORK (TCP/IP)
4
Access C
ontrol
LNL-2000
The LNL-2000 Intelligent System Controller (ISC) from Lenel is designed for advanced access
control applications. As the access control engine for the OnGuard system, the ISC provides
power and functionality. The ISC can communicate to the host computer in a single- or dual-path
configuration of Ethernet, dial-up or direct connect communication (RS-232/RS-485 combinations).
Multiple combinations of Input Control Modules, Output Control Modules, Biometric Gateways, and
Card Reader Interface Modules (up to 32 devices, 64 readers) can be configured.
The LNL-2000 can communicate upstream to the host computer at up to 115.2 Kbps via RS-232,
RS-485 multidropped, dial-up, or Ethernet communication. The LNL-2000 can store up to 350,000
cardholders online, and supports selective download for larger cardholder databases. The ISC has
two host communication ports. It also has four downstream communication ports, which support
either four 2-wire or two 4-wire RS-485 communication. In either configuration, you may connect
up to 32 devices in many combinations of LNL-1100, LNL-1200,LNL-1300, LNL-1320, LNL-500B,
and LNL-500W modules.
Features and Functionality
■ Host dual path communication enabled - direct wire (RS-232/RS-485 multi-dropped), Ethernet
TCP/IP, or dial-up communications
■ 1 MB on board memory expandable to 8 MB (up to 350,000 cardholders)
■ 12 VAC or 12 VDC input power
■ Supports up to 16 different formats (8 card formats and 8 asset formats)
■ Biometric template storage support for RSI®, Identix®, and Bioscrypt®
■ Enhanced anti-passback capabilities
■ Flash memory for real-time program updates
■ Lithium battery back-up for event memory
■ Up to 32,000 access level permissions
■ 255 holidays with grouping
■ 255 timezones, each with 6 intervals
■ Elevator control support for up to 128 floors
■ Alarm masking
■ Individual extended held open and strike times (ADA required)
■ Up to 9-digit user PIN codes
■ Status LEDs for heartbeat, upstream and downstream communication
■ Two dedicated inputs for tamper and power failure status
■ NIST Certified Advanced Encryption Standard (AES) 128-bit algorithm for communications
Intelligent System Controller
5
Acc
ess
Con
trol
LNL-2000
6
Controller OptionsLNL-2000Memory Options
LNL-1003MKLNL-1007MK
Host CommunicationsLNL-ETHLANLNL-ETHLAN-MICR
Dial-Up ModemLNL-56KEXTLNL-DC336K
SpecificationsPrimary Power (DC or AC)
DC input:AC input:
Memory and Clock BackupCommunication Ports
Port 1, 6:Ports 2-5:
InputsCabinet Tamper Monitor:Power Fault Monitor:
Wire RequirementsPower:RS-485:RS-232:Inputs:
EnvironmentalTemperature:
Humidity:Mechanical
Dimensions:Weight:
Approvals
Standard 1 MB on-board memory
3 MB memory expansion kit (Includes 3 MB memory and expansion board)7 MB memory expansion kit (Includes 7 MB memory and expansion board)
Micro serial server, flash ROM, DB25 serial port RJ-45 (10/100Base-T)CoBox Micro serial server, flash ROM, RJ-45 (10/100Base-T), diagnostic LEDs, dimensions 1.6 x 1.9 in. (40 x 49 mm), internally powered and includes standoffs
56 K external Modem with cables12 VDC-powered/33.6 K external modem for Intelligent System Controller
* The ISC is for use in low voltage, power-limited, class 2 circuits only.12 VDC ± 15%. 400 mA12 VAC ± 15%. 650 mA RMS 3 V lithium, type BR2325
RS-232 or RS-485 (2-wire or 4-wire) 9600 to 115.2 Kbps asyncRS-485 (2-wire or 4-wire) 9600 to 38.4K bps async
Unsupervised, dedicatedUnsupervised, dedicated
1 twisted pair, 18 AWG24 AWG twisted pair(s) with shield, 4000 ft. (1219 m) maximum24 AWG, 25 ft. (7.6 m) maximumTwisted pair, 30 ohms maximum
Operating: 32° to 158° F (0° to +70° C)Storage: -67° to 185° F (-55° to +85° C)0 to 95% RHNC
6 x 8 x 1 in. (152 x 203 x 25 mm)10 oz. (290 g) nominalUL 294 and 1076-listed, CE-marked, RoHS compliantNIST certified Advanced Encryption Standard (AES) 128-bit communication algorithm
RS-485 multidrop
LNL-1100Input Control Module
(Up to 16 Inputs perLNL-1100)
LNL-1200Output Control Module
(Up to 16 Outputs perLNL-1200)
LNL-1320Up to 32 Dual ReaderInterface Modules
Up to 32 Downstream Devices(64 Readers Max)
Downstream CommunicationFour 2-wire portsTwo 4-wire ports
Combination 2- and 4-wire ports
LNL-2000Intelligent System Controller
LNL-1300Up to 32 Single ReaderInterface Modules
LNL-1300
Hand GeometryReaders
FingerprintReadersor
LNL-500B
OnGuard Security Server
CORPORATE HEADQUARTERS LOCAL AREA NETWORK (TCP/IP)
Up to 8 Biometric Devices
Access C
ontrol
LNL-3300
The LNL-3300 Intelligent System Controller (ISC) by Lenel is designed for advanced access
control applications. As the access control engine for the OnGuard system, the ISC provides
power and functionality. The ISC can communicate to the host computer in a single- or dual-path
configuration of Ethernet, dial-up or direct connect RS-485 communication. Multiple combinations
of Input Control Modules, Output Control Modules and Card Reader Interface Modules (up to 64
devices) can be configured.
Utilizing its native Ethernet communications and an advanced 32-bit processor, the LNL-3300 can
communicate upstream to the host computer through its primary Ethernet port, with throughput up
to 8 times greater than the fastest serial connections. The secondary port can communicate at up
to 115.2 Kbps using 2-wire RS-485 multidrop, dial-up, or an Ethernet daughterboard connection.
The LNL-3300 can store up to 500,000 cardholders in non-volatile flash memory, and supports
selective download for larger cardholder databases. The two downstream RS-485 2-wire ports
can be used to connect up to 64 devices (64 doors) in many combinations of LNL-1100, LNL-1200,
LNL-1300, LNL-1320, LNL-500B, and LNL-500W modules.
Features and Functionality
■ On-board high-speed Ethernet 10/100Base-T upstream port provides up to 8 times higher
throughput than serial-to-Ethernet converters. DHCP and fixed IP addressing supported.
■ DNS device naming through DHCP extended commands
■ Host dual path communication enabled - on-board Ethernet TCP/IP, direct wire (RS-485, 2-wire
multidrop capable), or dial-up communications
■ 15 MB of available on-board, non-volatile flash memory
■ Battery-backed, non-volatile storage of 50,000 events
■ Firmware stored in flash memory, background download of firmware updates supported
■ 12 or 24 VDC input power
■ Supports up to 16 different formats (8 card formats and 8 asset formats)
■ Biometric template storage support for Schlage Recognition Systems®, Bioscrypt®,and Identix®
■ Enhanced anti-passback capabilities
■ Up to 32,000 access level permissions
■ 255 holidays with grouping
■ 255 timezones, each with 6 intervals
■ Elevator control support for up to 128 floors
■ Alarm masking
■ Individual extended held open and strike times (ADA required)
■ Up to 9-digit user PIN codes
■ Status LEDs for heartbeat & battery status, upstream and downstream communication, and
memory write status
■ Two dedicated inputs for tamper and power failure status
■ Advanced Encryption Standard (AES) 128-bit algorithm for communications
Intelligent System Controller
7
Acc
ess
Con
trol
LNL-3300
Controller OptionsLNL-3300
Secondary Host CommunicationsLNL-ETHLANLNL-ETHLAN-MICR
Dial-Up ModemLNL-56KEXTLNL-DC336K
SpecificationsPrimary Power (DC or AC)
DC input:Memory and Clock BackupCommunication Ports
Primary (Ethernet) Port 0:Secondary Upstream Port 1:Downstream Ports 2-3:
InputsCabinet Tamper Monitor:Power Fault Monitor:
Wire RequirementsPower:RS-485:RS-232:Inputs:
EnvironmentalTemperature:
Humidity:Mechanical
Dimensions:Weight:
Approvals
15 MB On-board flash memory available for cardholder & asset database50,000 event battery backed RAM for event log
Micro serial server, flash ROM, DB25 serial port RJ-45 (10/100Base-T)CoBox Micro serial server, flash ROM, RJ-45 (10/100Base-T), diagnostic LEDs, dimensions 1.6 x 1.9 in. (40 x 49 mm), internally powered and includes standoffs
56 K external modem with cables12 VDC-powered/33.6 K external modem for Intelligent System Controller
* The ISC is for use in low voltage, power-limited, class 2 circuits only.12 or 24 VDC ± 15%. 300 mA maximum3 V lithium, type BR2325, BR2330, CR2330
10/100Base-T Ethernet high-speed portRS-485 (2-wire) or RS-232 9600 to 115.2 Kbps async, optional Ethernet serial serverRS-485 (2-wire) 9600 to 38.4 Kbps async
Unsupervised, dedicatedUnsupervised, dedicated
1 twisted pair, 18 AWG24 AWG twisted pair(s) with shield, 4000 ft. (1219 m) maximum24 AWG, 25 ft. (7.6 m) maximumTwisted pair, 30 ohms maximum
Operating: 32° to 158° F (0° to +70° C)Storage: -67° to 185° F (-55° to +85° C)0 to 95% RHNC
5 x 6 x 1 in. (127 x 152.4 x 25 mm)4 oz. (115 g) nominalUL 294 and 1076-listed, CE-marked, ROHS compliantAdvanced Encryption Standard (AES) 128-bit communication algorithm, NIST certification pending
8
LNL-1300Up to 16 Single ReaderInterface Modules
LNL-1320Up to 16 Dual ReaderInterface Modules
OnGuard Security Server
CORPORATE HEADQUARTERS LOCAL AREA NETWORK (TCP/IP)
LNL-1100Input Control Module
(Up to 16 Inputs perLNL-1100)
LNL-1200Output Control Module
(Up to 16 Outputs perLNL-1200)
LNL-3300Intelligent
System Controller
RS-485 multidrop
Access C
ontrol
LNL-2220The LNL-2220 Intelligent Dual Reader Controller (IDRC) by Lenel provides a single board solution for interfacing one or two doors to an OnGuard system. In addition, other I/O and reader interface modules can be added on the LNL-2220’s downstream port to expand its capabilities. The LNL-2220 revolutionizes access control system architecture by allowing Ethernet connection directly from an entry location to the OnGuard server, while still providing the security, functionality, and modularity of Lenel’s proven hardware platform. The LNL-2220 is scalable for any access control application, from the most basic to the most sophisticated. In the event of communication loss, the LNL-2220 allows nearly all local functionality to continue unimpaired until the server connection is restored.
Utilizing its native Ethernet communications and an advanced 32-bit processor, the LNL-2220 can communicate upstream to the host computer through its Ethernet port (with a throughput up to eight times greater than the fastest serial connections), or at up to 115.2 Kbps using RS-232 communication directly or through an external dial-up modem. The LNL-2220 can store up to 250,000 cardholders in non-volatile flash memory, and supports selective download for larger cardholder databases. The downstream RS-485 two-wire port can be used to connect up to 32 devices (maximum 64 doors).
Two on-board reader ports support Data1/Data0, Clock/Data, Bioscrypt RS-485 readers and the bidirectional RS-485 Open Supervised Device Protocol (OSDP) communications. Each LNL-2220 supports up to eight different card formats. The LNL-2220 includes eight inputs that support normally open, normally closed, supervised, and unsupervised circuits. In addition, four output relays support fail-safe or fail-secure operation.
Features and FunctionalityController Functionality■ On-board Ethernet 10/100Base-T port provides up to 8 times greater throughput than
serial-to-Ethernet converters. DHCP and fixed IP addressing supported.■ DNS device naming through DHCP extended commands■ 6 MB of available on-board, non-volatile flash memory■ Battery-backed, non-volatile storage of 50,000 events■ Firmware stored in flash memory, background download of firmware updates supported■ Supports up to 16 different formats (8 card formats and 8 asset formats)■ Biometric template storage support for Schlage Recognition Systems®, Bioscrypt®, and Identix®.■ Direct connection of Bioscrypt RS-485 devices■ Enhanced anti-passback capabilities■ Up to 32,000 access level permissions■ 255 holidays with grouping, 255 timezones, each with 6 intervals■ Elevator control support for up to 128 floors■ Individual extended held open and strike times (ADA required)■ Up to 9-digit user PIN codes■ 20 status LEDs■ 2 dedicated inputs for tamper and power failure status■ 12 or 24 VDC input power■ Advanced Encryption Standard (AES) 128-bit algorithm for communications
Reader Interface Functionality■ Supports Data1/Data0, Clock/Data and Lenel OSDP-compatible RS-485 readers and keypads■ 4 Form-C relay outputs, 5 A at 30 VDC ■ Door contact supervision (open/closed) and REX push-button monitor for each door■ Strike control and auxiliary output for each door■ Bicolor reader status LED support plus beeper control, or 2-wire LED support ■ On-board regulator allows 12 VDC reader power from 24 VDC power source
Intelligent Dual Reader Controller
9
Acc
ess
Con
trol
LNL-2220
10
LNL-1300Up to 32 Single ReaderInterface Modules
LNL-2220Intelligent
System Controller
OnGuard Security Server
CORPORATE HEADQUARTERS LOCAL AREA NETWORK (TCP/IP)
LNL-1100Input Control Module
(Up to 16 Inputs perLNL-1100)
LNL-1200Output Control Module
(Up to 16 Outputs perLNL-1200)
RS-485 multidrop
Controller OptionsLNL-2220
Dial-Up ModemLNL-56KEXTLNL-DC336K
SpecificationsPrimary Power (DC or AC)
DC input:Event Memory and Clock BackupCommunication Ports
Primary (Ethernet) Port:Alternate Upstream Port 1:Downstream Port 2:
InputsTamper and Power Fail Monitors:Door position, REX, and AUX:
OutputsRelay outputs:
Reader PowerDC output:
Reader Port Compatibility
EnvironmentalTemperature:
Humidity:Mechanical
Dimensions:Weight:
Approvals
6 MB On-board flash memory available for cardholder & asset database,50,000 event battery backed RAM for event log
56 K external modem with cables12 VDC-powered/33.6 K external modem
* The LNL-2220 is for use in low voltage, power-limited, class 2 circuits only.12 or 24 VDC ± 15%. 500 mA maximum3 V lithium, type BR2325, BR2330, CR2330
10/100Base-T Ethernet high-speed portRS-232 9600 to 115.2 Kbps asyncRS-485 (2-wire) 9600 to 38.4 Kbps async
Unsupervised, dedicated8, each programmable as normally open or normally closed, supervised or unsupervised circuits
4 Form-C 5 A at 30 VDC relay outputs: 2 strike, 2 auxiliary
12 VDC, 125 mA regulated when 24 VDC powered, or 12 to 24 VDC 125 mA current limitedWiegand Data1/Data0, Magnetic Clock/Data, F/2F single-wire protocol, Bioscrypt RS-485,OSDP (Open Supervised Device Protocol RS-485)
Operating: 32° to 158° F (0° to 70° C)Storage: -67° to 185° F (-55° to 85° C)0 to 95% RHNC
6 x 8 x 1 in. (152 x 203 x 25 mm)9 oz. (255 g) nominalUL 294 and 1076-listed, CE-marked, ROHS compliantAdvanced Encryption Standard (AES) 128-bit communication algorithm, NIST certification pending
Access C
ontrol
LNL-1300 Series 2
Lenel Systems International offers a Single Reader Interface (SRI) module for access control
solutions. Access control card readers, keypads, or readers with keypads that use standard
Wiegand Data1/Data0 or Clock/Data communication are supported, as are those supporting the
bidirectional RS-485 Open Supervised Device Protocol (OSDP). Lock, unlock, and facility code
offline access modes are supported on all readers connected to the SRI. Each SRI supports up to
eight different card formats as well as issue codes for both magnetic and Wiegand card formats.
The SRI provides a vital link between the Intelligent System Controller (ISC) and the card reader
attached to the interface. As many as 32 SRI modules can be multidropped using RS-485 2-wire
communication up to 4,000 feet (1219 m) per port away from the ISC. Each SRI module is
individually addressed for increased reporting capabilities with OnGuard access control software
applications. The SRI includes two inputs that support normally open, normally closed, supervised,
and non-supervised circuits. Two output relays support fail-safe or fail-secure operation.
Features and Functionality
■ 12 or 24 VDC power supply
■ Supports Data1/Data0, Clock/Data and Lenel OSDP-compatible RS-485 readers and keypads
■ Two Form-C relay outputs (5 A door strike and 1 A aux relays)
■ Up to 16 different card formats (8 card formats and 8 asset formats)
■ Issue code support
■ Downloadable firmware
■ Door contact open or closed, supervised or non-supervised
■ REX push-button monitor - supervised or non-supervised
■ Strike control output
■ Bicolor or 2-wire reader status LED support
■ Reader beeper control
■ Plastic mounting channel
■ Support for offline reader access mode
■ Elevator control, support for 64 floors
Single Reader Interface Module
11
Acc
ess
Con
trol
LNL-1300 Series 2
12
Power Supplies & EnclosuresLNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
SpecificationsPrimary Power (DC)
DC input:Reader Power
DC output:Reader Port Compatibility
EnvironmentalTemperature:
Humidity:Mechanical
Dimension:Weight:
Approvals
Lenel UL-listed 4 A, 110 VAC power supply - 12 or 24 VDC 4 A output (switch-selectable), 120 VAC input, continuous supply current with enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS capable (battery optional), UL-listedLenel UL listed power supply - 12 or 24 VDC 6 A output (switch-selectable), 120 VAC (1.6 amps) input, continuous supply current with enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS capable (battery optional), UL-listedBattery kit - 12 VDC, 12 AH battery (PS-12120)
* The SRI is for use in low voltage, power-limited, class 2 circuits only.12 or 24 VDC ± 15%. 125 mA
12 VDC 125 mA max current limitedWiegand Data1/Data0Magnetic Clock/DataF/2F single-wire protocolOpen Supervised Device Protocol (RS-485)
Operating: 32° to 158° F (0° to +70° C)Storage: -67° to 185° F (-55° to +85° C)0 to 95% RHNC
2.9 x 4.25 x 1.4 in. (74 x 108 x 36 mm)4 oz. (120 g) nominalUL 294 and 1076-listed, CE-marked, RoHS compliant
OnGuard Security Server
RS-485 multidrop
LNL-1300Single ReaderInterface Module
LNL-1100Input Control Module
(Up to 16 Inputs perLNL-1100)
LNL-1200Output Control Module
(Up to 16 Outputs perLNL-1200)
LNL-1320Dual ReaderInterface Module
Intelligent System Controller
CORPORATE HEADQUARTERS LOCAL AREA NETWORK (TCP/IP)
Access C
ontrol
LNL-1320 Series 2
Lenel Systems International offers a Dual Reader Interface (DRI) module for access control
solutions. Most access control card readers, keypads, or readers with keypads that use standard
Wiegand Data1/Data0 or Clock/Data communication are supported, as are those that support the
bidirectional RS-485 Open Supervised Device Protocol (OSDP). Lock, unlock, and facility code
offline access modes are supported on all readers connected to the DRI. Each DRI supports up to
eight different card formats as well as issue codes for both magnetic and Wiegand card formats.
The DRI provides a vital link between the Intelligent System Controller (ISC) and the card reader
attached to the interface. As many as 32 DRI modules can be multidropped using RS-485 2-wire
or 4-wire communication up to 4,000 feet per port away from the ISC. Each DRI module is
individually addressed for increased reporting capabilities with OnGuard access control software
applications. The DRI includes eight inputs that support normally open, normally closed,
supervised, and non-supervised circuits. In addition, six output relays support fail-safe or
fail-secure operation.
Features and Functionality
■ 12 or 24 VDC power supply
■ Supports Data1/Data0, Clock/Data and Lenel OSDP-compatible RS-485 readers and keypads
■ Downloadable firmware
■ Six Form-C 5 A at 30 VDC relay outputs
■ Up to 16 different formats (8 card formats and 8 asset formats)
■ Issue code support for magnetic and Wiegand formats
■ Door contact supervision (open/closed)
■ REX push-button monitor
■ Strike control output
■ Bicolor reader status LED support and 2-wire LED support
■ Beeper control
■ Dedicated tamper and power failure circuits
■ Support for offline reader access mode
■ On-board jumpers for termination
■ On-board regulator allows 12 VDC reader support from 24 VDC power source
■ DIP switch-selectable addressing
Dual Reader Interface Module
13
Acc
ess
Con
trol
14
LNL-1320 Series 2
Power Supplies & EnclosuresLNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
SpecificationsPrimary Power (DC)
DC input:Reader Power
DC output:Reader Port Compatibility
EnvironmentalTemperature:
Humidity:Mechanical
Dimension:Weight:
Approvals
Lenel UL-listed 4 A, 110 VAC power supply - 12 or 24 VDC 4 A output (switch-selectable), 120 VAC input, continuous supply current with enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery optional), UL-listedLenel UL Listed Power Supply - 12 or 24 VDC 6 A output (switch-selectable), 120 VAC (1.6 amps) input, continuous supply current with enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery optional), UL-listedBattery kit - 12 VDC, 12 AH battery (PS-12120)
* The DRI is for use in low voltage, power-limited, class 2 circuits only.12 or 24 VDC ± 15%. 450 mA
12 VDC, 125 mA regulated or 12 to 24 VDC 125 mA current limitedWiegand Data1/Data0Magnetic Clock/DataF/2F single-wire protocolOpen Supervised Device Protocol (RS-485)
Operating: 0° to +70° C (32° to 158° F)Storage: -55° to +85° C (-67° to 185° F)0 to 95% RHNC
6 x 8 x 1 in. (152 x 203 x 25 mm)10 oz. (290 g) nominalUL 294 and 1076-listed, CE-marked, ROHS compliant
OnGuard Security Server
RS-485 multidrop
LNL-1300Single ReaderInterface Module
LNL-1100Input Control Module
(Up to 16 Inputs perLNL-1100)
LNL-1200Output Control Module
(Up to 16 Outputs perLNL-1200)
LNL-1320Dual ReaderInterface Module
Intelligent System Controller
CORPORATE HEADQUARTERS LOCAL AREA NETWORK (TCP/IP)
Access C
ontrol
LNL-1100 Series 2
The Lenel Input Control Module (ICM) provides the access control system with high-speed
acknowledgment of critical alarm points in monitored areas. The ICM communicates directly with
the Intelligent System Controller (ISC) either by 2-wire or 4-wire RS-485 communication. The ICM
has 16 configurable input control points and 2 output control relays. It supports normally open,
normally closed, supervised and non-supervised circuits.
The input circuits are scanned using an analog-to-digital converter. The digitized input status
signal is software-monitored and controlled, so that each input point can be programmed as a
supervised or non-supervised alarm point.
The output relays can also be configured for fail-safe or fail-secure operation. Each relay supports
the “On,” “Off,” and “Pulse” Lenel OnGuard software commands.
Features and Functionality
■ Grade B, A, and AA line supervision
■ 12 or 24 VDC input power
■ 16 programmable supervised or non-supervised contacts
■ 2 Form-C 5 A, 30 VDC contacts for load switching
■ 2 dedicated inputs for tamper and power failure status
■ On-board termination jumpers
■ DIP switch-selectable addressing
■ Elevator control, support for 64 floors
■ Status LED for host communication and heartbeat
■ Variable resistor values for line supervision
■ Downloadable firmware
Input Control Module
15
Acc
ess
Con
trol
16
LNL-1100 Series 2
Power Supplies & EnclosuresLNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
SpecificationsPrimary Power (DC)
DC input:Memory and Clock BackupEnvironmental
Temperature:
Humidity:Mechanical
Dimension:Weight:
Approvals
Lenel UL-listed 4 A, 110 VAC power supply - 12 or 24 VDC 4 A output (switch-selectable), 120 VAC input, continuous supply current with enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery optional), UL-listedLenel UL-listed power supply - 12 or 24 VDC 6 A output (switch-selectable), 120 VAC (1.6 A) input, continuous supply current with enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery optional), UL-listedBattery Kit - 12 VDC, 12 AH battery (PS-12120)
* The ICM is for use in low voltage, power-limited, class 2 circuits only.12 or 24 VDC ± 15%. 350 mA3 V lithium, type BR2325
Operating: 0° to +70° C (32° to 158° F)Storage: -55° to +85° C (-67° to 185° F)0 to 95% RHNC
6 x 8 x 1 in. (152 x 203 x 25 mm)10 oz. (290 g) nominalUL 294 and 1076-listed, CE-marked, ROHS compliant
OnGuard Security Server
RS-485 multidrop
LNL-1300Single ReaderInterface Module
LNL-1100Input Control Module
(Up to 16 Inputs perLNL-1100)
LNL-1200Output Control Module
(Up to 16 Outputs perLNL-1200)
LNL-1320Dual ReaderInterface Module
Intelligent System Controller
CORPORATE HEADQUARTERS LOCAL AREA NETWORK (TCP/IP)
Access C
ontrol
LNL-1200 Series 2
The Lenel Output Control Module (OCM) communicates directly with the Intelligent System
Controller (ISC) by either 2-wire or 4-wire RS-485 communication. Each OCM is an
individually-addressed device, and counts as a single device on all Intelligent System Controllers.
The OCM can be operated by either 12 or 24 VDC power. Each OCM includes dedicated tamper
and power failure input contacts.
The OCM has 16 programmable output relays that can be configured for fail-safe or fail-secure
operation. Each relay supports the “On,” “Off,” and “Pulse” Lenel OnGuard software commands.
Features and Functionality
■ 16 Form-C 5 A, 30 VDC contacts for load switching
■ 12 or 24 VDC input power
■ 2 dedicated digital inputs for tamper and power failure status
■ RS-485 communication, multidropped (2-wire or 4-wire RS-485)
■ Up to 16 OCMs per Intelligent System Controller
■ On-board termination jumpers
■ DIP switch-selectable addressing
■ Status LEDs for communication to the host, heartbeat and relay status
■ Elevator control, support for 64 floors
Output Control Module
17
Acc
ess
Con
trol
LNL-1200 Series 2
18
Power Supplies & EnclosuresLNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
SpecificationsPrimary Power (DC)
DC input:Environmental
Temperature:
Humidity:Mechanical
Dimension:Weight:
Approvals
Lenel UL-listed 4 A, 110 VAC power supply - 12 or 24 VDC 4 A output (switch-selectable), 120 VAC input, continuous supply current with enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery optional), UL-listedLenel UL-listed power supply - 12 VDC or 24 VDC 6 A output (switch-selectable), 120 VAC (1.6 amps) input, continuous supply current with enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery optional), UL-listedBattery kit - 12 VDC, 12 AH battery (PS-12120)
* The OCM is for use in low voltage, power-limited, class 2 circuits only.12 or 24 VDC ± 15%. 500 mA
Operating: 32° to 158° F (0° to +70° C)Storage: -67° to 185° F (-55° to +85° C)0 to 95% RHNC
6 x 8 x 1 in. (152 x 203 x 25 mm)16 oz. (454 g) nominalUL 294 and 1076-listed, CE-marked, ROHS compliant
OnGuard Security Server
RS-485 multidrop
LNL-1300Single ReaderInterface Module
LNL-1100Input Control Module
(Up to 16 Inputs perLNL-1100)
LNL-1200Output Control Module
(Up to 16 Outputs perLNL-1200)
LNL-1320Dual ReaderInterface Module
Intelligent System Controller
CORPORATE HEADQUARTERS LOCAL AREA NETWORK (TCP/IP)
Access C
ontrol
LNL-500B
The Lenel Biometric Reader Interface Gateway (BRI) is an extremely versatile and vital link
between the Lenel LNL-2000 or LNL-3300 Intelligent System Controllers (ISCs) and biometric
readers from multiple manufacturers. Using OnGuard Access, the gateway can be uniquely
configured to support Recognition Systems hand geometry readers, Identix fingerprint readers or
Bioscrypt fingerprint readers.
The BRI communicates at 38.4Kbps via RS-485 multidropped configuration to the ISC. The
gateway has two downstream RS-485 2-wire ports, each of which supports up to 4 uniquely
addressed biometric readers. Each downstream port supports biometric readers located up to
4,000 feet (1219 m) away from the BRI.
Features and Functionality
■ Host and downstream communications - 38.4 Kbps, 2-wire RS-485 multidropped
communications
■ 12 VDC or 12 VAC input power @ 250 mA or 400 mA
■ Supports up to 8 biometric readers
■ Supported biometric readers:
• Ingersoll Rand® - HandKey II, ID3D and HandKey CR
• Identix® V20
• Bioscrypt® V-FLEX, V-PASS-FX and V-STATION
• Lenel LNL-BIO007-xxx
■ Flash memory for real time program updates
■ Status LEDs for heartbeat, upstream and downstream communications
■ Two dedicated inputs for Cabinet Tamper and Power Failure status
■ On-board RS-485 termination jumpers
■ Easy to configure dip switches for address and communications speeds
■ Supports fingerprint and PIN code two-factor authentication
■ On-board program configuration and clock battery backup
Biometric Reader Interface Gateway
19
Acc
ess
Con
trol
LNL-500B
20
Enrollment Kit
RS-232Communication
LNL-500B
Intelligent System Controller(64 readers maximum)
LAN/WAN
One LNL-500B per port RS-485 Communication
RS-232, RS-485, Ethernet, Dial-up Communication
Ports3 2
Any supportedaccess reader
Any supportedaccess reader
LNL-1300Up to 32 Single ReaderInterface Modules
LNL-1320Up to 32 Dual ReaderInterface Modules
Ports 2 - 5
Eight Readers Per Biometric Gateway
(address 00-07)
Software Link(s) Between Readers
Software Link(s) Between Readers
Interface OptionsLNL-500B
Power Supplies & EnclosuresLNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
SpecificationsPrimary Power (DC or AC)
DC input:AC input:
Memory and Clock backupEnvironmental
Temperature:
Humidity:Mechanical
Dimensions:Weight:
ApprovalsSupported Readers
Lenel Biometric Reader Interface Gateway - 12 VDC or 12 VAC, (5 year lithium battery) 512KB standard memory, support for a maximum of 8 IR Hand Geometry readers per interface
Lenel UL Listed 4 A, 110 VAC Power Supply - 12 VDC or 24 VDC 4 A output (switch selectable), 120 VAC input, continuous supply current with enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery optional), UL-listedLenel UL Listed Power Supply - 12 VDC or 24 VDC 6 A output (switch selectable), 120 VAC (1.6 amps) input, continuous supply current with enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery optional), UL-listedBattery Kit - 12 VDC, 12 AH battery (PS-12120)
* The LNL-500B is for use in low voltage, power limited, class 2 circuits only.12 VDC ± 15%. 250 mA12 VAC ± 15%. 400 mA RMS 3 V lithium, type BR2325
Operating: 32° to 158° F (0° to +70° C)Storage: -67° to 185° F (-55° to +85° C)0 to 95% RHNC
6 x 5 x 1 in. (152 x 127 x 25 mm)8 oz. (230 g) nominalUL 294 and 1076-listed, CE-marked, RoHS compliantIngersoll Rand - HandKey, HandKey II, HandKey CR and ID3D readers (Firmware version 1.21 or later required)Identix V20 Readers (Firmware version 2.12 or later required)Bioscrypt V-FLEX and V-STATION (Firmware version 7.30 or later required)Lenel BioGuard Readers (LNL-BIO007-xxx)
Access C
ontrol
LNL-500W
The Lenel Wireless Reader Interface (WRI) Gateway module provides an innovative solution to
interface with Wireless products from Schlage. The gateway provides the link from the Lenel
Intelligent System Controller (ISC) to the Panel Interface Module (PIM-485-OTD) wireless receiver.
This configuration will support up to 16 Schlage wireless reader products per gateway.
The PIM-485-OTD operates in the 900 MHz license-free band, allowing rapid, no-hassle
deployment. Installation time for a standard secured entry point that requires a door contact,
Request to Exit switch, reader and door strike is reduced by as much as 40%. The 900 MHz
spread spectrum delivery model has been extensively tested to ensure that communications are
ultra-reliable. Using this wireless configuration, communicating between OnGuard and the
Schlage wireless readers is both simple and dependable.
The gateway can communicate at 38.4Kbps via RS-485 multidropped configuration to the ISC.
The gateway has two downstream RS-485 2 wire ports. Port 3 supports one PIM-485-OTD
receiver, which in turn supports up to 16 uniquely addressed Schlage Wireless reader products.
The gateway can be installed up to 4000 feet (1219 m) away from the PIM-485-OTD. This
configuration is supported for all ISCs: LNL-500, LNL-1000 and LNL-2000.
Features and Functionality
■ Host and downstream communications - 38.4 Kbps, 2 wire RS-485 multidropped
communications
■ 12 VDC or 12 VAC input power @ 250 mA or 400 mA
■ Supports up to 16 Schlage Wireless readers
■ Supported Schlage Wireless readers include:
• WA 5296 Wireless Cylindrical Lock
• WA 5696 Wireless Mortise Lock
• WA 5694 Wireless Mortise Lock with 1” Autobolt
• WA 993 Wireless Exit Kit
• WRI (Wireless Reader Interface)
• WPR (Wireless Portable Reader)
■ Flash memory for real-time program updates
■ Status LEDs for heartbeat, upstream and downstream communications
■ Two dedicated inputs for Cabinet Tamper and Power Failure status
■ On-board RS-485 termination jumpers
■ Easy to configure dip switches for address and communication speeds
■ On-board program configuration and clock battery backup
Wireless Reader Interface Gateway
21
Acc
ess
Con
trol
LNL-500W
22
Reader OptionsLNL-500W
Power Supplies & EnclosuresLNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
SpecificationsPrimary Power (DC or AC)
DC input:AC input:
Memory and Clock backupEnvironmental
Temperature:
Humidity:Mechanical
Dimensions:Weight:
ApprovalsSupported Readers
Lenel Wireless Reader Interface Gateway - 12 VDC or 12 VAC, (5 year lithium battery) 512KB standard memory, support for a maximum of 16 Wireless readers per interface. Requires OnGuard software version 5.10.4xx or later
Lenel UL Listed 4 A, 110 VAC Power Supply - 12 VDC or 24 VDC 4 A output (switch selectable), 120 VAC input, continuous supply current with enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery optional), UL-listedLenel UL Listed Power Supply - 12 VDC or 24 VDC 6 A output (switch selectable), 120 VAC (1.6 amps) input, continuous supply current with enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery optional), UL-listedBattery Kit - 12 VDC, 12 AH battery (PS-12120)
* The LNL-500W is designed for use in low voltage, power limited, class 2 circuits only.12 VDC ± 15%. 250 mA12 VAC ± 15%. 400 mA RMS 3 V lithium, type BR2325
Operating: 32° to 158° F (0° to +70° C)Storage: -67° to 185° F (-55° to +85° C)0 to 95% RHNC
6 x 5 x 1 in. (152 x 127 x 25 mm)8 oz. (230 g) nominalUL 294-listed, CE-marked, RoHS compliantSchlage Wireless - WA 5296, WA 5696, WA 5694, WA 993, WRI, WPR
WA 5296 Cylindrical
Ports2 3
WA 5696 MortiseWRI-OTD
Note: Up to 16 MIRL, IRL, WRI or WPR per LNL-500W
Ports 2 - 5LNL-500W
Schlage WirelessOnGuard Integration
for PIM-485-OTD
OnGuard Security Server
CORPORATE HEADQUARTERS LOCAL AREA NETWORK (TCP/IP)
PIM-485-OTD
Access C
ontrol
LNL-8000
The Star Multiplexer from Lenel is designed to implement star topology on a downstream port of
any Lenel Intelligent System Controller or on any host communication port of any OnGuard server.
Up to eight RS-485 (2-wire) connections or four RS-485 (4-wire) connections can be made
downstream of the LNL-8000. The Lenel Star Multiplexer requires 12 VDC for power. It allows
communication protocol conversion, and provides connection with alternate communication
devices to extend effective distances.
The master or host interface can use either RS-232 or RS-485 (2-wire) communication. The Lenel
Star Multiplexer interfaces upstream with the Lenel ISC, and downstream with one of many Lenel
RS-485 products (including the LNL-1100 Input Control Module, LNL-1200 Output Control Module,
LNL-1300 Single Reader Interface Module, LNL-1320 Dual Reader Interface Module and
LNL-500A, LNL-500B, or LNL-500W Gateway Interface Modules) on each downstream port (ports
2-9). A maximum of eight (8) devices are allowed per downstream port.
Features and Functionality
■ Host communications - 38.4 Kbps direct wire (RS-232/RS-485 multidropped)
■ 12 VDC input power
■ Status LEDs for heartbeat, upstream and downstream communication
■ Support for either 2-wire or 4-wire RS-485 topologies
■ RS-485 on-board termination is jumper selectable
■ Can be used for retrofit and new wiring configurations
Star Multiplexer
23
Acc
ess
Con
trol
LNL-8000
24
Mechanical and Architectural Characteristics and WiringRequirements
Communications
Power Supplies & EnclosuresLNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
SpecificationsPrimary Power (DC or AC)
DC input:Environmental
Temperature:
Humidity:Mechanical
Dimensions:Weight:
Approvals
The acceptable power supply is 12 VDC. Locate the power source as close as possible to the LNL-8000.Use a minimum of 18 AWG (one twisted pair) wiring for the power supply. Communication with the Intelligent System Controller is via a 2-wire or 4-wire RS-485 interface. The interface allows multidrop communication on a single ISC port, up to 4,000 feet (1219 m) away per port. It also can be used to convert a single RS-232 communication port to a multidrop RS-485 port. Use twisted pair(s) with a minimum of 24 AWG and a shield for communication. The 2-wire or 4-wire communications with end-of-line termination are jumper-selectable.
Lenel UL-listed 4 A, 110 VAC power supply - 12 VDC or 24 VDC 4 A output (switch-selectable), 120 VAC input, continuous supply current with enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery optional), UL-listedLenel UL-listed power supply - 12 VDC or 24 VDC 6 A output (switch-selectable), 120 VAC (1.6 amps) input, continuous supply current with enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery optional), UL-listedBattery kit - 12 VDC, 12 AH battery (PS-12120)
* This module is for use in low voltage, power limited, class 2 circuits only.12 VDC ± 15%, 250 mA
Operating: 32° to 158° F (0° to +70° C)Storage: -67° to 185° F (-55° to +85° C)0 to 95% RHNC
6 x 5 x 1 in. (152 x 127 x 25 mm)4 oz. (180 g) nominalUL 294 and 1076-listed, CE-marked
LNL-1300
OnGuard Security
Server
LNL-1320
2 3 4 5 6 7 8 9
LNL-8000Star Multiplexer
2 3 4 5 6 7 8 9
LNL-8000Star Multiplexer(Up to 4 multiplexers)Up to 32 Downstream
RS-485 Devices(up to 8 per port)
1 2 3 4 1 2 3 4 1 2 3 4
Intelligent System Controller
Intelligent System Controller
Intelligent System Controller
Access C
ontrol
LNL-2005WLenel Systems International’s magnetic card access readers are durable, dependable, convenient, and competitively-priced. The magnetic card access readers are available in both 12 VDC and optional 5 VDC models. The readers have a fully-weatherized metal casing shell that provides strength and durability. The readers are first treated with an anti-corrosion film, then coated with a tough, abrasion-resistant, beige or black textured finish that complements any interior or exterior decor. The readers accept low and high coercivity magnetic stripe cards. Track 2 magnetic readers are standard, but Track 1 and Track 3 readers are available optionally.
The readers communicate to the Intelligent System Controller (ISC) through one of two reader interface modules. The single (LNL-1300) or dual (LNL-1320) reader interface module interprets magnetic (Clock/Data) data from the reader, and sends the signal back to the ISC via RS-485 communication. The reader can be located up to 500 feet (152 m) away from the reader interface module.
Features■ 12 VDC power supply (optional 5 VDC available)■ Bidirectional card swipe■ One million card pass read head■ Choice of three attractive weatherproof finishes: black, beige, antique brass■ Single bicolored LED for reader status■ Audible indicator beeper contacts■ Strike controlled by reader interface■ DIP switch-selectable data outputs■ Maximum 500 feet (152 m) distance from reader interface module■ RJ-45 jack for quick installation■ Track 2 standard (Track 1 and 3 optional)
SpecificationsPrimary power (DC)
DC input:
Current:Environmental
Temperature:
Humidity: Mechanical
Dimension:Weight:
Approvals
Magnetic Card Access Reader
25
* The reader is for use in low voltage, power-limited, class 2 circuits only.12 V model: 12 VDC (10.2 to 13.8 VDC)5 V model: 5.8 VDC (4.9 to 6.4 VDC) 50 mA maximum, 25 mA typical
Operating: 32° to 158° F (0° to +70° C)Storage: -67° to 185° F (-55° to +85° C)0 to 95% RHNC
1.95 x 5.50 x 1.30 in. (50 x 140 x 33 mm)10 oz. (290 g) nominalUL 294 and 1076-listed, CE-marked
Acc
ess
Con
trol
LNL-2010/2020 series Lenel Systems International’s Magnetic Card Access Readers are durable, dependable, convenient and competitively priced. The Magnetic Card Access Readers are available in both 12 VDC and optional 5 VDC models. The LNL-2010W is a magnetic swipe only reader, and the LNL-2020W includes a twelve-position keypad (available with an indestructible keypad). The readers have a fully weatherized metal casing shell, which provides strength and durability. The readers are first treated with an anti-corrosion film and then coated with a tough, abrasion resistant, beige or black textured finish that complements any interior or exterior decor. The readers accept low and high coercivity magnetic stripe cards. Track 2 magnetic readers are standard, but optional Track 1 or Track 3 readers are available.
The readers communicate with the Intelligent System Controller (ISC) through one of two reader interface modules. The single (LNL-1300) or dual (LNL-1320) reader interface module interprets the Wiegand communication (Data 1/Data 0 or Clock and Data) from the reader and sends the signal back to the ISC via RS-485 communication. The reader can be located up to 500 feet (152 m) away from the reader interface module.
Features■ Host communications - 38.4 Kbps direct wire (RS-232/RS-485 multidropped), Ethernet TCP/IP,or dial-up communication■ 12 VDC power supply (optional 5 VDC available)■ Bidirectional card swipe■ One million card pass read head■ Choice of three attractive weatherproof finishes: black and beige (antique brass optional)■ Two single-color LEDs for reader status■ Track 2 default (optional Track 1 and 3)■ Audible indicator beeper contacts■ Strike controlled by reader interface module■ DIP switch selectable data outputs■ Maximum 500 feet (152 m) distance from reader interface module■ RJ-45 jack for quick installation■ Optional tamper switch■ 12-position keypad (LNL-2020W only)■ (Optional) indestructible keypad, LNL-2020W-NDK
SpecificationsPrimary power (DC)
DC input:
Current:Environmental
Temperature:
Humidity: Mechanical
Dimension:Weight:
Approvals
Magnetic Card Access Readers
26
* The ISC is for use in low voltage, power-limited, class 2 circuits only.12 V Model: 12 VDC (10.2 to 13.8 VDC)5 V Model: 5.8 VDC (4.9 to 6.4 VDC) 50 mA maximum, 25 mA typical
Operating: 32° to 158° F (0° to +70° C)Storage: -67° to 185° F (-55° to +85° C)0 to 95% RHNC
1.9 x 5.5 x 1.3 in. (50 x 140 x 33 mm)10 oz. (290 g) nominalUL 294 and 1076-listed, CE-marked
Access C
ontrol
LenelProx LPSR-2400
The LenelProx LPSR-2400 special range proximity reader is Lenel’s latest engineering
achievement. With a respectable read range of 4 to 5.5 in. (102 to 140 mm), the LPSR-2400
delivers exceptional read range without compromising quality, durability, or performance.
The LPSR-2400 is a full-featured, Wiegand-compatible reader with LED and annunciator. The
LPSR-2400 reader is metal-compensated, resulting in minimal loss of read range when mounted
on a metal mullion.
The LPSR-2400’s electronics are potted in UL-approved potting compound to seal them against
adverse environmental conditions. The reader is manufactured in an ISO 9000-certified facility to
meet the highest quality standard. The attractive enclosure comes in a dark gray or beige color,
and may be mounted on mullions or single-gang electrical boxes, or directly to an interior or
exterior wall.
Features
■ Read range: 4 to 5.5 in. (102 to 140 mm)
■ Electronics potted with epoxy compound for protection in demanding environmental applications
■ LED for visual feedback, piezo for audio feedback
■ Compatible with all Wiegand access control systems
■ Industry standard Wiegand (26- to 56-bit) output
■ Attractive high-tech enclosure
Specifications
■ Transmitting frequency: 125 kHz
■ Voltage: 5 to 12 VDC
■ Current requirement: 40 to 70 mA
■ Output format: Wiegand
■ Operating temperature: -31° to 150° F (-35° to 65° C)
■ Operating humidity: 0 to 95% non-condensing
■ Weight: 4 oz. (113 g)
■ Dimensions: 4.5 x 1.8 x 0.7 in. (114 x 45 x 18 mm)
■ Color: Dark gray (standard) or beige
■ Cable: 10 conductor (#22 AWG) stranded with continuous shield for typical Wiegand installations
■ Certifications: Complies with FCC Part 15, UL 294-Listing and CE-Mark pending
Proximity Reader
27
Acc
ess
Con
trol
LenelProx LPMM-6800
Lenel’s standard mullion mount reader (LPMM-6800) offers the read range of a mid-range reader
at the cost of a “mini.” It is designed to be mounted directly on a metal door frame/mullion.
Because it is metal-compensated, there is minimal reduction in read range. The LPMM-6800 has a
read range of 6 to 8 in. (152 to 203 mm). It is designed for indoor and outdoor applications.
The LPMM-6800’s electronics are potted with a UL-approved compound that makes them
impervious to the elements. The reader is manufactured in an ISO 9000-certified facility to achieve
the highest quality standard. It is highly reliable, warranted for life, and available in either dark gray
(standard) or beige color.
The LPMM-6800 reader can easily be configured to meet the needs of virtually any access control
system. The reader outputs both Wiegand and RS-232 data, and features annunciator and LED
feedback.
Features
■ Read range: 6 to 8 in. (152 to 203 mm)
■ Compact modular design for metal frame (mullion) mounting
■ Electronics potted with epoxy compound for protection in demanding environmental applications
■ LED for visual feedback, piezo for audio feedback
■ Industry-standard Wiegand and RS-232 output
■ Indoor and outdoor application
Specifications
■ Transmitting frequency: 125 kHz
■ Voltage: 5 to 12 VDC
■ Current requirement: 50 to 80 mA
■ Audio alarm: 4 kHz burst
■ Output formats: Wiegand & RS-232
■ Operating temperature: -31° to 150° F (-35° to 65° C)
■ Operating humidity: 0 to 95% non-condensing
■ Weight: 6 oz. (170 g)
■ Dimensions: 6.0 x 1.75 x 1.0 in. (152 x 44 x 254 mm)
■ Color: Dark gray (standard) or beige
■ Cable: 10 conductor (#22 AWG) stranded with continuous shield for typical Wiegand installations
■ Certifications: Complies with FCC Part 15, UL 294-Listing and CE-Mark pending
Mullion Mount Proximity Reader
28
Access C
ontrol
LenelProx LPSP-6820
The LenelProx LPSP-6820 proximity reader is ideally suited for applications where a tasteful
appearance makes a difference. It has an attractive package that looks good whether it is placed
outside the boardroom or at the front gate in the rain or snow.
The LPSP-6820 offers a stylish appearance and a superior read range of 6 to 8 in. (152 to 203
mm). It is designed to be mounted on a standard single-gang electric wall box, or on the surface of
an interior or exterior wall. The LPSP-6820 is available in dark gray or beige color, and is certain to
blend in with the architectural design of any building. It is easily installed, and the two-piece
construction allows the covers to be switched to accommodate color changes.
The LPSP-6820 outputs Wiegand and RS-232 formats and is compatible with all access control
systems. The electronics are potted with UL-approved potting compound that protects the reader
from harsh environmental conditions. It is manufactured in an ISO 9000-certified facility to achieve
the highest quality standards. The LPSP-6820 is highly reliable, warranted for life and capable of
providing the best read range in its class.
Features
■ Read range: 6 to 8 in. (152 to 203 mm)
■ Electronics potted with epoxy compound for demanding environmental applications
■ LED for visual feedback, piezo for audio feedback
■ Industry-standard Wiegand and RS-232 output
■ Proximity technology – no contact required
■ Attractive, high-tech enclosure
■ Indoor and outdoor applications
Specifications
■ Transmitting frequency: 125 kHz
■ Voltage: 5 to 12 VDC
■ Current requirement: 50 to 80 mA
■ Audio alarm: 4 kHz burst
■ Output formats: Wiegand and RS-232
■ Operating temperatures: -31° to 150° F (-35° to 65° C)
■ Operating humidity: 0 to 95% non-condensing
■ Weight: 8 oz. (227 g)
■ Dimensions: 4.6 x 3.1 x 0.65 in. (117 x 79 x 17 mm)
■ Color: Dark gray (standard) or beige
■ Cable: 10 conductor (#22 AWG) stranded with continuous shield for typical Wiegand installations
■ Certifications: Complies with FCC Part 15, UL 294-Listing and CE-mark pending
Proximity Reader
29
30
Acc
ess
Con
trol
LenelProx LPKP-6840
The LenelProx LPKP-6840 reader is a combination keypad and switchplate proximity reader. It is
specifically designed for high-security applications that require dual verification.
The LPKP-6840 proximity reader offers dual functionality and a superior read range of 6 to 8 in.
(152 to 203 mm). It is designed to mount on a standard single-gang electric wall box, or on the
surface of an interior or exterior wall. The entire unit is UL 294-listed as an indoor/outdoor access
control device.
The LPKP-6840 keypad/proximity reader outputs industry-standard Wiegand (26 to 56 bit) format.
The keypad output is programmable to match the requirements of a majority of access control
systems. The proximity reader also simultaneously outputs an RS-232 signal, which duplicates the
Wiegand output from the proximity cards/tags for integration with time and attendance or debit
systems. It is manufactured in an ISO 9000-certified facility to achieve the highest quality
standards. The LPKP-6840 is highly reliable, warranted for life, and capable of outputting Wiegand
data in multiple configurations.
Features
■ Read range: 6 to 8 in. (152 x 203 mm)
■ LED for visual feedback, piezo for audio feedback
■ Industry-standard Wiegand and simultaneous RS-232 output
■ Lifetime warranty
■ Available in a choice of keypad output configurations (default is 8 bit)
Specifications
■ Transmitting frequency: 125 kHz
■ Voltage: 5 to 12 VDC
■ Current requirement: 50 to 120 mA
■ Audio alarm: 4 kHz burst
■ Output formats:
• Wiegand and RS-232 for card/tag reader
• Wiegand only for keypad
■ Operating temperatures: -31° to 150° F (-35° to 65° C)
■ Operating humidity: 0 to 95% non-condensing
■ Weight: 8 oz. (227 g)
■ Dimensions: 4.6 x 3.1 x 0.875 in. (117 x 79 x 22 mm)
■ Color: Dark gray or beige
■ Cable: 10 conductor stranded with continuous shield for typical Wiegand installations
■ Certifications: Complies with FCC Part 15, UL 294-Listing and CE-Mark pending
Proximity Reader with Keypad
Access C
ontrol
LenelProx LPMR-1824
The LenelProx LPMR-1824 is a standout among mid-range proximity readers. It boasts an
industry-best 18 to 24 in. (457 to 610 mm) read range, and a compact enclosure. No more
misreads or fumbling to get the card close enough to the reader. The LPMR-1824 reads at
maximum range every time. And it does so at an unprecedented 600 mA at 12 VDC.
The LPMR-1824 is designed for indoor or outdoor applications. Its electronics are potted with a
UL-approved epoxy to seal them against adverse environmental conditions. The LPMR-1824 is
manufactured in an ISO 9000-certified facility to achieve the highest quality standard. It is highly
reliable and has a lifetime warranty. It has both Wiegand and RS-232 protocol interfaces, and is
compatible with all standard access control systems.
The two-piece construction of the LPMR-1824 makes for fast and easy installation.
Features
■ Read range: 18 to 24 in. (457 to 610 mm)
■ Electronics potted with epoxy compound for weather resistance
■ LED for visual feedback, piezo for audio feedback
■ Compatible with all Wiegand access control systems
■ Channeled housing allows for rear or side mounting
■ Proximity technology - no contact required
■ Metal-compensated version available for mounting on metal surface
■ Industry standard Wiegand and RS-232 data output
Specifications
■ Transmitting frequency: 125 kHz
■ Voltage: 5 to 12 VDC
■ Current requirement: 250 to 600 mA
■ Audio alarm: 4 kHz burst
■ Operating temperature: -31° to 150° F (-35° to 65° C)
■ Operating humidity: 0 to 95% non-condensing
■ Weight: 25 oz. (709 g)
■ Dimensions: 8.0 x 8.0 x 1.0 in. (203 x 203 x 254 mm)
■ Color: Dark gray
■ Cable: 10 conductor (#22 AWG) stranded with continuous shield for typical Wiegand installations
■ Certifications: Complies with FCC Part 15, UL 294, 1076-Listing and CE-Mark pending
Mid-Range Proximity Reader
31
Acc
ess
Con
trol
LenelProx LPLR-911
The LenelProx LPLR-911 long range reader is in a class by itself, with an industry-best, 9 to 11 ft.
(2.75 x 3.35 m) read range within and a compact package. The LPLR-911 is ideal for outdoor
applications such as AVI (automatic vehicle identification), parking entry, and gate controls. The
LPLR-911 is also perfect for indoor applications such as asset monitoring and tracking.
Operating in the license-free 900 MHz band, the LPLR-911 is the first access control reader to
combine the convenience of 900 MHz technology with a fast multi-tag feature and Wiegand format
output. The multi-tag capability makes it easy to set up portal or hallway asset monitoring stations
to determine the flow of assets.
The innovative construction of the LPLR-911 reader seals it against adverse environmental
conditions. It is manufactured in an ISO 9000-certified facility to achieve the highest quality
standard. The reader delivers an impressive combination of high styling and superior range. It
offers Wiegand and RS-232 protocol interfaces and compatibility with all standard access control
systems.
Features
■ Read range: 9 to 11 ft. (2.75 to 3.35 m) with 1.0 A at 6.5 VDC, to 0.4 A at 15 VDC
■ Housing sealed for weather resistance
■ Anti-collision technology and multiple tag reading capability
■ Compatible with existing access control system and asset tracking systems
■ Utilizes passive tag technology (no battery)
Specifications
■ Industry standard Wiegand and RS-232 data output
■ Transmitting frequency: 902 to 928 MHz
■ Voltage: 6.5 to 15 VDC
■ Current requirement: 1.0 to 0.4 A
■ Output formats: Wiegand and RS-232
■ Operating temperature: -31° to 150° F (-35° to 65° C)
■ Operating humidity: 0 to 95% non-condensing
■ Weight: 37.5 oz. (1.06 kg)
■ Dimensions: 8 x 9.5 x 1.125 in. (203 x 241 x 286 mm)
■ Color: Beige
■ Cable: 9 conductor stranded (#22 AWG) with continuous shield for typical installations
■ Certifications: Complies with FCC Part 15, UL 294-Listing and CE-Mark pending
Long Range Proximity Reader
32
Access C
ontrol
LNL-XF
The Lenel OpenCard Reader series includes the most flexible readers in the industry. A single
reader supports all applicable ISO standards (14443 and 15693), including the new U.S.
Government PIV standard. All Lenel OpenCard Readers contain both 125 kHz proximity and
13.56 MHz contactless smart card support in one unit. Lenel OpenCard Readers provide
compatibility with Lenel prox, HID® proximity, GE/CASI ProxLite®, XceedID proximity, AWID
proximity and most 13.56 MHz technologies (see chart on back). By offering 125 kHz and 13.56
MHz technology in one reader, Lenel protects customers from obsolescence in the transition from
proximity technology to contactless smart card technology. Even if customers want to continue
using proximity technology today, the new Lenel OpenCard Readers offer economical migration to
the latest in smart card technology while accommodating their budget or timeline.
Product Applications
The mullion reader is perfect for narrow-rail mullion installations. It can be used as a sleek and
unobtrusive unit, as well as for standard wall-mounted reader applications.
The mid-range reader is ideal for mounting on single gang US electrical boxes. The read range
provided by this attractive package makes it the standard of choice for most wall-mounted
installations.
The mid-range keypad reader is ideal for higher security applications where two-factor (card
and/or PIN) authentication is desired. This reader may be mounted on a standard U.S. single gang
electrical box, or used in any typical wall-mounted application.
Features and Functionality
■ Compatibility: compatible with industry standard 125 kHz proximity and 13.56 MHz contactless
technologies
■ Easy migration
■ Optional GSA approved PIV support
■ Modular design: allows easy removal or addition of keypad in the field
■ Read range: up to 8 in. (203 mm), depending on card technology
■ Integrated tamper detection
■ Tri-state LED (red, green, amber): Visual indicator and audio feedback representing status and
activity information
■ Accommodates interior, exterior, metal and non-metal installation environments
■ Lifetime warranty against defective workmanship and materials
Lenel OpenCard™ Readers
33
Acc
ess
Con
trol
LNL-XF
34
Supported Standards and Technologies125 kHz Proximity
ISO 15693 13.56 MHz Vicinity
Reader OptionsStandard ReadersLNL-XF1100DLNL-XF2100DLNL-XF2110D
SpecificationsFrequencyStandardsOperating TemperaturePhysical Dimensions (HWD)
LNL-XF1100D:
LNL-XF21XXD:
WeightLNL-XF1100D:LNL-XF21XXD:
Voltage RangeMax. Current Requirement
LNL-XF1100D:LNL-XF2100D:LNL-XF2110D:
MaterialSystem InterfaceCable SpecificationCabling DistanceCertifications
LenelProxGE CASI ProxLite®
HID® ProximityXceedID™
AWID® Proximity
XceedID ISO-X™ Secure SectorInfineon my-d® Secure SectorHID iCLASS® Serial NumberInfineon my-d® Serial NumberInside Contactless PicoTag® Serial No.ST Microelectronics® Serial NumberTexas Instruments Tag-It® Serial No.
125 kHz and 13.56 MHzISO 15693 and ISO 14443-31° to 151°F (-35° to 67°C)
5.85” x 1.72” x 1.14” (149 cm x 43 cm x 29 mm)5.85” x 4.5” x 1.45” (149 cm x 114 cm x 37 mm)
0.6 lbs. (.27 kg)1.05 lbs. (.48 kg)8 to 16 VDC
Avg. 95 mA DC, Peak 254 mA DCAvg. 95 mA DC, Peak 218 mA DCAvg. 120 mA DC, Peak 215 mA DCPBT PolymerWiegand (Standard)22AWG 12 Conductor ShieldedWiegand Output: 500 ft. (152m)FCC CertificationCanadian FCC CertificationUL 294-Listed, CE-MarkedR&TTE Directive (15 EU Countries)GSA Approved for FIPS-201 (PIV models only)
ISO 14443 13.56 MHz Proximity
Max. Read Range125 kHz:
LNL-XF1100D, up to 5” (127 mm)LNL-XF21XXD, up to 8” (203 mm)
13.56 MHz:ISO 15693
• LNL-XF1100D, up to 4.5” (114 mm)• LNL-XF21XXD, up to 6” (152 mm)
ISO 14443 MIFARE Standard• LNL-XF1100D, up to 2” (51 mm)• LNL-XF21XXD, up to 3” (76 mm)
ISO 14443 MIFARE DESFire• LNL-XF1100D, up to 1.5” (38 mm)• LNL-XF21XXD, up to 2.5” 64 mm)
ISO 14443 PIV• LNL-XF1100D, up to 1” (25 mm)• LNL-XF21XXD, up to 2” (51 mm)
*Maximum read range depends on credential type/form factor andinstallation conditions
Lenel OpenCard Format SectorXceedID Secure MIFAREDESFire® Serial NumberMIFARE® Serial NumberU.S. Government PIV Data Model
Description(Standard Black) Mullion mount; Wiegand output(Standard Black) 1-Gang US mount; Wiegand output(Standard Black) 1-Gang US mount; Keypad; Wiegand output
PIV ReadersLNL-XF1100D-PIVLNL-XF2100D-PIVLNL-XF2110D-PIV
Access C
ontrol
Lenel OpenProx™ Reader
35
LNL-XF1050The Lenel OpenProx Reader is the most flexible 125 kHz proximity card reader in the industry. It supports all major 125 kHz card standards. The Lenel OpenProx Reader provides compatibility with HID® proximity, GE/CASI ProxLite®, XceedID® proximity, AWID®, and LenelProx card formats. Lenel provides a single compact reader that can integrate diverse proximity card populations, or allow seamless transition from one 125 kHz technology to another.
Product ApplicationsThe mullion reader is perfect for narrow-rail mullion installations. It can be used as a sleek and unobtrusive unit, as well as in standard wall-mounted reader applications.
Features and Functionality■ Compatible with industry standard 125 kHz proximity technology■ Easy Migration■ Tri-state LED (red, green, amber): Visual indicator and audio feedback representing status and
activity information■ Accommodates interior, exterior, metal and non-metal installation environments■ Lifetime warranty against defective workmanship and materials
SpecificationsFrequency:Operating temperature:Physical dimension (HWD):
Weight:Voltage range:Power supply:Max. current requirement:
Material:Max. read range:
System interface:Cable specification:
Cabling distance:
Certifications:
125 kHz-31° to 151°F (-35° to 67°C)4.1” x 1.72” x 1.0”(104 cm x 44 cm x 25 mm)0.45 lbs. (.20 kg)5 to 16 VDCLinear DCAvg. 55 mA DCPeak 167 mA DCPBT PolymerUp to 3” (76 mm)** Maximum read range depends on credential type/form factor and installation conditionsWiegandRecommended cable is 22AWG (18AWG preferred), minimum 5 conductor shielded (4 plus shield)in retrofit installs. Wiegand Output 18 AWG: 500 ft. (152 m)Wiegand Output 22 AWG: 200 ft. (60 m)FCC CertificationCanadian FCC CertificationUL 294 and 1076-listedR&TTE Directive (15 EU Countries)CE-marked
Acc
ess
Con
trol
Three-Factor Biometric Reader Recessed Enclosure
36
LNL-BIO-007-ENC
The LNL-BIO-007 Reader Recessed Enclosure is designed to mount any model of the BIO-007
series of readers. The enclosure comes standard with a brushed aluminum finish plate.
Alternatively, it can be ordered with black or gold finish plates to match BIO-007 reader color
options. The enclosure comes standard with six ¾” to 1” (19 to 25 mm) conduit knock outs,
security screws and a security tool. The recessed enclosure contains a built-in 24VAC input to
12VDC output power for a single BIO-007 reader. The enclosure can be used for new or existing
installations.
Specifications
Enclosure
■ Dimensions (approximate): 11.25 x 5.25 x 3.25 in. (286 x 133 x 83 mm)
■ Color: Gray
■ Finish plate: brushed aluminum is standard; black or gold optional
■ Includes reader mounting screws and hardware
■ Suggested mounting height - approximately 54” (1371.6 mm) from floor to top of unit
Linear Power Supply/Charger
■ 12VDC output
■ 2 Amps of continuous supply current @ 12VDC
■ 24 VAC transformer requirements per unit
■ 24 VAC/40VA for 12VDC output (not included)
■ Filtered and electronically regulated outputs
■ Short circuit and thermal overload protection
■ Built-in charger for sealed lead acid or gel type battery backup
■ Maximum charge current: 0.3 Amp
■ Zero voltage drop upon transfer to battery backup
■ AC input and DC output LED indicators
■ Lifetime warranty
Board
■ Dimensions (approximate): 3.0 x 2.5 x 1.5 in. (76 x 64 x 38 mm)
Access C
ontrol
LNL-BIO-007
The LNL-BIO-007 access reader is durable, dependable, and competitively priced. Designed for
indoor or outdoor use, the reader combines three forms of authentication: proximity reader, PIN
pad, and fingerprint sensor. The PIN and fingerprint authentication are standard; the proximity
reader is optional. All three reader modes can be configured to support timezone control.
The BIO-007 transmits a credential number to the Intelligent System Controller through a Wiegand
interface. The ISC then delivers fingerprint template(s) to the BIO-007 though the LNL-500B
Biometric Gateway and matching is performed within the BIO-007. The results of the match are
then returned to the Gateway for appropriate action and reporting to OnGuard.
The indestructible keypad is based on BaranTec’s patented Piezo Switch technology. The
power-driven Bioscrypt fingerprint sensor utilizes a powerful DSP processor. Unlike other biometric
products, this sensor is hidden until a valid credential and/or PIN is presented. Then the fingerprint
sensor door opens. After verification occurs, the fingerprint sensor door closes into a secure
vandal-resistant position.
Features and Functionality
■ 12 VDC power supply @ 1.8 amps
■ Three factors of authentication: card, PIN, fingerprint
■ Data output: Wiegand Data1/Data0
■ Biometric output: RS-485
■ Keypad interface: 8-bit burst
■ Keypad layout: 4 across & 3 down
■ Brushed aluminum finish, also available in black finish
■ Vandal-resistant design
■ Weather-resistant housing
■ Three LEDs for reader status
■ Audible indicator buzzer
■ 24-month warranty
Three Factor Biometric Reader
37
Acc
ess
Con
trol
LNL-BIO-007
38
Reader OptionsLNL-BIO007LNL-BIO007-HIDLNL-BIO007-HIDW
Reader FinishesStandardAlternate
SpecificationsPrimary Power (DC)
DC input:Environmental
Temperature:Humidity:
MechanicalCase:Dimensions:Weight:Read range:Mounting height:
TechnologySupported:Sensor:FAR:FRR:
Approvals
Reader unit with PIN pad and fingerprint sensor.Reader unit with built-in HID technology (HID 125 KHz proximity sensor).Outdoor reader with thermal heat kit. Recommended for readers installed outdoors, where temperature is below -4° F. (-20° C)
Silver finishBlack finish (To specify the alternate finish, add the following suffix to the part number: -B)
* The BIO-007 reader is for use in low voltage, power-limited, class 2 circuits only.12 VDC @ 1.6 amps (12 VDC @ 1.8 amps with use of thermal heat kit)
32° to 122° F (0° to 50°C), operating. (-4° to 158° F / -20° to +70°C with use of thermal heat kit)0 to 95% RHNC
Brushed aluminum construction, anodized3.94 x 8.92 x 2.6 in. (100 x 227 x 66 mm)4.71 lbs. (2.1365 kg) nominal1 to 2 in. ( 25 to 51 mm)Between 48 and 54 in. (1219 and 1372 mm) recommended
Encoding: 125 KHz HID proximity cardsBioscrypt(False Acceptance Rate) 0.2%(False Rejection Rate) 1.0%CE-Marked
LNL-2000 Intelligent System Controller
LNL-500B LNL-1300/1320RS - 485 multidrop
BIO-007
Proximity and keypad Wiegand output to reader interface module (6 wires)
RS-485 to fingerprint sensor (3 wires)
Access C
ontrol
LNL-826S121NN
Lenel Systems International’s indestructible keypads offer the ultimate in strength and durability
where PIN entry and maximum security are required. With a tamperproof keypad and a
weatherproof, solid brushed aluminum casing, Lenel indestructible keypads are designed to
function dependably even in harsh climates or high-risk environments. The keypads are compliant
with the Americans with Disabilities Act (ADA) guidelines.
The LNL-826S121NN 12-position keypad is configured to have two keys across by six keys down,
and is intended for use in mullion mounting applications. It features an eight-bit word data output
format, 12 to 28 volts DC power, 30 mA current draw, and red and green status LEDs. The keypad
uses solid state piezo sounder technology to provide audible feedback. A natural aluminum color
is standard, but other colors are also available upon request.
Features
■ Anodized graphics
■ Waterproof and dustproof IP68
■ 2 x 6 in. (51 x 152 mm) configuration keypad type
■ Click and lock mounting screws
Specifications
■ Protocol: 8 bit word output
■ Dimensions: 7.1 x 1.8 x 0.8 in. (44 x 181 x 19 mm)
■ Power: 12 to 28 VDC
■ Current: 30 mA
■ Environment: IP68; 100% RH
■ Temperature: -40° to 158 F° (-40° to +70° C)
■ FCC-certified, CE-marked
■ Brushed aluminum construction; other colors available optionally
Application Note
Lenel keypad readers can be used either by themselves or in conjunction with almost any other
reader technology. The eight-bit burst output format enables these keypads to be wired in parallel
with any other reader technology, including proximity, magnetic stripe, MIFARE, Vicinity, etc.
Detailed wiring information is provided in the Lenel hardware installation manuals.
Indestructible Keypad
39
Acc
ess
Con
trol
LNL-834S121NN
Lenel Systems International’s indestructible keypads offer the ultimate in strength and durability
where PIN entry and maximum security are required. With a tamperproof keypad and a
weatherproof, solid brushed aluminum casing, Lenel indestructible keypads are designed to
function dependably even in harsh climates or high-risk environments. The keypads are compliant
with the Americans with Disabilities Act (ADA) guidelines.
The LNL-834S121NN 12-position keypad is configured to have three keys across by four keys
down, and is intended for single gang electrical box installation. It features an eight-bit word data
output format, 12 to 28 volts DC power, 30 mA current draw, and red and green status LEDs. The
keypad uses solid state piezo sounder technology to provide audible feedback. A natural aluminum
color is standard, but other colors are also available upon request.
Features
■ Anodized graphics
■ Waterproof and dustproof IP68
■ 3 x 4 in. (76 to 102 mm) configuration keypad type
■ Click and lock mounting screws
Specifications
■ Protocol: 8 bit word output
■ Dimensions: 3.2 x 5.1 x 0.8 in. (81 x 130 x 19 mm)
■ Power: 12 to 28 VDC
■ Current: 30 mA
■ Environment: IP68; 100% RH
■ Temperature: -40° to 158° F (-40° to +70° C)
■ FCC-certified, CE-marked
■ Brushed aluminum construction; other colors available optionally
Application Note
Lenel keypad readers can be used either by themselves or in conjunction with almost any other
reader technology. The eight-bit burst output format enables these keypads to be wired in parallel
with any other reader technology, including proximity, magnetic stripe, MIFARE, Vicinity, etc.
Detailed wiring information is provided in the Lenel hardware installation manuals.
Indestructible Keypad
40
Access C
ontrol
BT-LPKP-NDK
The Lenel BT-LPKP-NDK indestructible keypad reader offers the ultimate in strength and durability
where proximity and PIN entry are required. With a tamperproof keypad and a weatherproof, solid
brushed aluminum casing, Lenel indestructible keypads are designed to function dependably even
in harsh climates or high-risk environments. The keypads are compliant with the Americans with
Disabilities Act (ADA) guidelines.
The model BT-LPKP-NDK reader is equipped with two electronically interlocked devices – a Lenel
format proximity reader and a piezoelectric keypad – contained within a single, nearly
indestructible, metal housing. The 12-position keypad is configured to have three keys across by
four keys down, and is designed for both international and U.S. single gang electrical box
mounting applications. It features an eight-bit word data output format, 5 to 12 volts DC power, 120
mA current draw, and red and green status LEDs. The keypad uses solid state piezo sounder
technology to provide audible feedback. A natural aluminum color is standard, but other colors are
also available upon request.
Features
■ Anodized graphics
■ Waterproof and dustproof IP68
■ 3 x 4 in. (76 x 102 mm) configuration keypad type
■ Click and lock mounting screws
Specifications
■ Protocol: Wiegand + 8 bit word output
■ Dimensions: 5.4 x 3.3 x 1.2 in. (137 x 83 x 30 mm)
■ Power: 5 to 12 VDC
■ Current: 120 mA
■ Environment: IP68; 100% RH
■ Temperature: -4° to 158 F° (-20° to +70° C)
■ Read Range: 2 to 3 in. (51 to 76 mm)
■ FCC-Certified/UL, ULC- and CE-mark pending
■ Brushed aluminum construction; other colors available optionally
Indestructible Keypad with Lenel Proximity
41
Acc
ess
Con
trol
BT-ASPKP-HID/iCLASS
The Lenel BT-ASPKP-HID/BT-ASPKP-iCLASS indestructible keypad reader offers the ultimate in
strength and durability where proximity and PIN entry are required. With a tamperproof keypad
and a weatherproof, solid brushed aluminum casing, Lenel indestructible keypads are designed to
function dependably even in harsh climates or high-risk environments. The keypads are compliant
with the Americans with Disabilities Act (ADA) guidelines.
The model BT-ASPKP-HID/BT-ASPKP-iCLASS reader is equipped with two electronically
interlocked devices – an HID format proximity or iCLASS reader, and a piezoelectric keypad –
contained within a single, indestructible, metal housing. The 12-position keypad is configured to
have two keys across by five keys down, and is designed for both international and U.S. single
gang electrical box mounting applications. It features an eight-bit word data output format, 5 to 12
volts DC power, 150 mA current draw, and red and green status LEDs. The keypad uses solid
state piezo sounder technology to provide audible feedback. A natural aluminum color is standard,
but other colors are also available upon request.
Features
■ Anodized graphics
■ Waterproof and dustproof IP68
■ 2 x 5 in. (51 x 127 mm) configuration keypad type
■ Click and lock mounting screws
Specifications
■ Protocol: Wiegand + 8 bit word output
■ Dimensions: 4.7 x 3.5 x 0.8 in. (120 x 90 x 20 mm)
■ Power: 5 to 12 VDC
■ Current: 150 mA
■ Environment: IP68; 100% RH
■ Temperature: -4° to 158 F° (-20° to +70° C)
■ Read Range: 1 to 2 in. (25 to 51 mm)
■ FCC-Certified Part 15, CE-marked
■ Brushed aluminum construction; other colors available optionally
■ Available in either 125 MHz proximity or 13.56 iCLASS
Indestructible Keypad with HID® Proximity or iCLASS™ 13.56
42
Access C
ontrol
LNL-CK
The LNL-CK Lenel Command Keypad integrates a 32-character backlit LCD display with a
16-position keypad and a reader port. The command keypad serves as a command reader,
a reader from which user commands can be issued to execute local I/O functions. Reader
command programming is accomplished using the OnGuard System Administration application.
The LNL-CK display indicates time in either 12 or 24-hour clock format. The format is automatically
chosen based on the regional settings of the computer on which the Communication Server is
running. The LNL-CK display also provides command status and other text feedback during reader
operations. For example, when performing the Extended Held Open command, the LNL-CK
displays the countdown time before the Held Open time is reached, as well as basic intrusion
arm/disarm functions.
The LNL-CK communicates with the Lenel Intelligent System Controller (ISC) either through direct,
multidrop, 2-wire RS-485 communication to the ISC, or through a reader port of a Lenel Dual
Reader Interface Module (LNL-1320).
The LNL-CK may be configured in one of three ways: as a stand-alone RS-485 device, as an
alternate reader to a primary reader, or as a reader device connected to the Wiegand input of a
LNL-1320. In any of these modes, an optional reader with a Data1/Data0 or clock/data output may
be connected to the LNL-CK to provide Card Only, Card or PIN, or Card and PIN capability.
Features and Functionality
■ 32-character backlit LCD display
■ 16-position keypad with 4 function keys
■ Supports all “approved for use” reader technologies from Lenel that communicate using
Data1/Data0 or clock/data communication
■ Arm, Disarm, Bypass and Force Arm alarm mask groups
■ Extended Held Open Time via Command Keypad with feedback
■ Reader command support
■ Works with all Lenel Intelligent System Controllers (LNL-500, LNL-1000, LNL-2000)
■ Supports reader mode changes by Timezone control
■ Supports PIN mode on LNL-CK keypad. With optional reader, all other modes are also
supported
■ Ability to adjust backlight on/off times
■ Flash upgradable firmware
■ Built-in DIP switch selectable RS-485 termination
Lenel Command Keypad
43
Acc
ess
Con
trol
LNL-CK
44
SpecificationsPrimary Power
Voltage:Current:
ReaderPower:LED Control:Buzzer Control:Interface:
EnvironmentalTemperature:
Humidity:
12 VDC +/- 15%175 mA terminal only
Pass-through (non-regulated)2-wire or 1-wire bicolor LEDAvailable with 1-wire LED control2-wire RS-485, or Wiegand
Operating: 32° to 122° F (0° to 50° C)Storage: -4° to 158° F (-20° to 70° C)0% to 95% RHNC
PhysicalColor:Dimensions:Weight:Mounting:
TechnologyCommunication:
Approvals
RS-485
LNL-CK
LNL-CK
AlternateReader
AlternateReader
Intelligent System
Controller
LNL-1320
2-WIRE RS-485 SERIAL BUS
White6.75 x 5.00 x 1.0 in. (172 x 127 x 25 mm)14 oz. (400 g) nominalSurface-mount or 3-gang box
RS-485: up to 4000 ft. (1219 m) max,24 AWG, 100 ohm impedanceWiegand: up to 500 ft. (152 m) max,18 AWG stranded wire
FCC approved, UL-listed, CE-marked
Access C
ontrol
LNL-AL400ULXThe LNL-AL400ULX is a power-limited supply/charger that will convert a 115 VAC 50/60 Hz input, into a power-limited 12 VDC or 24 VDC output (see specifications).
Features■ LNL-CTX enclosure (gray with Lenel logo)■ Offline power supply (AL400ULXL) mounted on custom Lenel bracket■ Tamper switch■ Lenel lock with two keys■ 16 stand-offs and 16 screws■ Battery leads■ Installation instructions■ Can accommodate up to 2 Lenel Access Control modules
Specifications■ UL 294 and 1076-listed■ Switch selectable 12 VDC or 24 VDC power limited output■ Class 2 rated■ Input 115 VAC 50/60 Hz, 1.45 amp■ Maximum charge current 0.7 amp■ 4 amps continuous supply current at 12 VDC■ 3 amps continuous supply current at 24 VDC■ Filtered and electronically regulated outputs■ Built-in charger for sealed lead acid or gel type batteries (Optional ABT-12)■ Automatic switchover to standby battery when AC fails■ AC input and DC output LED indicators■ AC fail supervision (form C contacts)■ Low battery supervision (form C contact)■ Low battery disconnect prevents batteries from deep discharge■ Thermal overload protection■ Short circuit protection■ Primary circuit switch for incoming 115 VAC■ Power supply board dimensions: 4.3 x 7 x 1.8 in. (108 x 178 x 44 mm)■ Enclosure dimensions: 12 x 16 x 4.5 in. (304 x 406 x 114 mm)
Ordering InformationPart Number:LNL-AL400ULXABT-12LNL-CTX
UL-Listed, Multi-Agency Power Supply/Charger
45
Description:115 VAC configurationBattery backup optionCabinet only, with lock 12 x 16 x 4.5 in. (304 x 406 x 114 mm)
Acc
ess
Con
trol
LNL-AL600ULX-4CB6The LNL-AL600ULX-4CB6 is a power-limited supply/charger that will convert a 115 VAC 60 Hz input, into a non-power-limited 12 VDC or 24 VDC output (see specifications)
Features■ LNL-CTX-6 enclosure (gray with Lenel logo)■ Offline power supply (AL600ULXL) mounted on custom Lenel bracket■ Power limited distribution module (PD4-CB)■ Tamper switch■ Lenel lock with two keys■ 48 stand-offs and 48 screws■ Battery leads■ Installation instructions■ Can accommodate up to 6 Lenel Access Control modules
Specifications■ UL 294 and 1076-listed■ Switch selectable 12 VDC or 24 VDC non-power limited output■ Input 115 VAC 60 Hz, 1.9 amp■ Maximum charge current 0.7 amp■ 6 amps continuous supply current at 12 VDC or 24 VDC■ Filtered and electronically regulated outputs■ 100 mV peak output voltage ripple■ 4 individual circuit breaker outputs■ Surge protected outputs■ Built-in charger for sealed lead acid or gel type batteries (Optional ABT-12)■ Automatic switchover to standby battery when AC fails■ Zero voltage drop when switched over to battery backup■ AC input and DC output LED indicators■ AC fail supervision (form C contacts)■ Low battery and battery presence supervision (form C contact)■ Thermal overload protection■ Short circuit protection■ Primary circuit switch for incoming 115 VAC ■ Power supply board dimensions: 4.3 x 7 x 1.8 in. (108 x 178 x 44 mm)■ Enclosure dimensions: 24 x 18 x 4.5 in. (610 x 457 x 114 mm)
Ordering InformationPart Number:LNL-AL600ULX-4CB6ABT-12LNL-CTX-6
UL-Listed, Multi-Agency Power Supply/Charger
Description:115 VAC configurationBattery backup optionCabinet only, with lock 24 x 18 x 4.5 in. (610 x 457 x 114 mm)
46
Access C
ontrol
LNL-400X-CE220
The LNL-400X-CE220 is a power-limited supply/charger that will convert a 230 VAC, 60 Hz input
into a power-limited, 12 VDC or 24 VDC output (see specifications).
Features
■ LNL-CTX enclosure (gray with Lenel logo)
■ AL400ULB power supply
■ Tamper switch
■ Lenel lock with two keys
■ 16 standoffs and 16 screws
■ Battery leads
■ Installation instructions
■ Can accommodate up to 2 Lenel Access Control modules
Specifications
■ CE-marked
■ Switch-selectable, 12 VDC or 24 VDC, power-limited output
■ Class 2 rated
■ Input 230 VAC, 60 Hz, 1.45 amp
■ Maximum charge current 0.7 amp
■ 4 amps continuous supply current at 12 VDC
■ 3 amps continuous supply current at 24 VDC
■ Filtered and electronically regulated outputs
■ Built-in charger for sealed lead acid or gel type batteries (Optional ABT-12)
■ Automatic switchover to standby battery when AC fails
■ AC input and DC output LED indicators
■ AC fail supervision (form C contacts)
■ Low battery supervision (form C contact)
■ Low battery disconnect prevents batteries from deep discharge
■ Thermal overload protection
■ Short circuit protection
■ Primary circuit switch for incoming 230 VAC
■ Power supply board dimensions: 4.3 x 7 x 1.8 in. (108 x 178 x 44 mm)
■ Enclosure dimensions: 12 x 16 x 4.5 in. (304 x 406 x 114 mm)
Ordering Information
Part Number:LNL-400X-CE220
ABT-12
LNL-CTX
CE-Marked Power Supply/Charger
47
Description:230 VAC configuration
Battery backup option
Cabinet only, with lock 12 x 16 x 4.5 in. (304 x 406 x 114 mm)
Acc
ess
Con
trol
LNL-600X6-CE220
The LNL-600X6-CE220 is a power-limited supply/charger that will convert a 230 VAC, 60 Hz input
into a non-power-limited, 12 VDC or 24 VDC output (see specifications)
Features
■ LNL-CTX-6 enclosure (gray with Lenel logo)
■ AL600ULB power supply
■ Power-limited distribution module (PD4-CB)
■ Tamper switch
■ Lenel lock with two keys
■ 48 standoffs and 48 screws
■ Battery leads
■ Installation instructions
■ Can accommodate up to 6 Lenel Access Control Modules
Specifications
■ CE-marked
■ Switch-selectable, 12 VDC or 24 VDC, non-power-limited output
■ Input 230 VAC, 60Hz, 1.9 amp
■ Maximum charge current 0.7 amp
■ 6 amps continuous supply current at 12 VDC or 24 VDC
■ Filtered and electronically regulated outputs
■ 100 mV peak output voltage ripple
■ 4 individual circuit breaker outputs
■ Surge protected outputs
■ Built-in charger for sealed lead acid or gel type batteries (Optional ABT-12)
■ Automatic switchover to standby battery when AC fails
■ Zero voltage drop when switched over to battery backup
■ AC input and DC output LED indicators
■ AC fail supervision (form C contacts)
■ Low battery and battery presence supervision (form C contact)
■ Thermal overload protection
■ Short circuit protection
■ Primary circuit switch for incoming 230 VAC
■ Power supply board dimensions: 4.3 x 7 x 1.8 in. (108 x 178 x 44 mm)
■ Enclosure dimensions: 24 x 18 x 4.5 in. (610 x 457 x 114 mm)
Ordering Information
Part Number:LNL-600X6-CE220
ABT-12
LNL-CTX-6
CE-Marked Power Supply/Charger
Description:230 VAC configuration
Battery backup option
Cabinet only, with lock 24 x 18 x 4.5 in. (610 x 457 x 114 mm)
48
CAM-20Z704-USB / CAM-21Z704-USBP
The Lenel USB Image CaptureKit offers many important features for capturing badgeholder
images. The capture kit includes a high resolution CCD (NTSC or PAL) camera with software
zoom capabilities, a fully-synchronized cool white built-in flash, a tripod system with a powered
base, TWAIN-compliant software, a USB communication cable and a universal power cable. The
camera is USB 2.0-compliant, producing high resolution live video for image capture using the
OnGuard ID CredentialCenter™ application by Lenel. The latest version of the TWAIN device
driver enables the user to control the camera’s zoom capabilities from within OnGuard. The built-in
flash illuminates both video fields evenly to minimize the effect of poor lighting environments.
Features and Functionality
■ USB 1.1 (USB 2.0 compliant)
■ Cool white LEDs replace hot incandescent lights & last up to 100 times longer
■ Single control button for camera & LED, transparent & seamless via USB
■ TWAIN-compliant software interacts with OnGuard and other imaging software
■ Rapid image download compared to still image cameras
■ Real-time subject setup and scene adjustment
■ Freeze frame perfection
USB Capture Kit
49
USB Out S-Video Out
Video Out
Power • LED• Camera/Remote
Credential
CAM-20Z704-USB / CAM-21Z704-USBP
50
Camera OptionsCAM-20Z704-USB
CAM-21Z704-USBP
SpecificationsElectrical
CCD sensor:Active pixels (HxV):Horizontal resolution:Sensitivity:Signal to noise ratio:Gamma:Gain:Synchronization:Back light compensation:Shutter speed (fixed):
Mirror mode:Positive/negative mode:Iris:Video output:
Camera Power:Camera Power Consumption:
USB VideoVideo Capture:
High Resolution Still Image Capture:
Supported Image Formats:Software Drivers:
USB Bandwidth:
USB Standard:PC Minimum System Requirements:
USB NTSC CCD Image Capture Kit - includes CCD NTSC camera, synchronized cool white lights, telescoping stand, USB cable, universal 110/220 VAC power supply and device drivers.USB PAL CCD Image Capture Kit - includes CCD PAL camera, synchronized cool white lights, telescoping stand, USB cable, universal 110/220 VAC power supply and device drivers.
1/4” (6.35 mm) Sony interline CCD768 x 494 NTSC, 752 x 582 PAL>470 (TVL)1 lux at 30 IRE (F1.4 AGC Max)>48 dBDefault 0.45Automatic or manualInternal Automatic or offNTSC: Auto/Man (1/60 to 1/10000)PAL: Auto/Man (1/50 to 1/10000)Selectable on/offSelectable on/offAuto or manualUSB 1.1, USB 2.0 compliantCVBS 1Vp-p (75ohm) & Y/C (S-Video)12 VDC (9.0 to 15 VDC)5.4 watts
30 fps CIF (352 x 288)15 fps VGA (640 x 480)NTSC: 640 x 480320 x 240 RGB 24 BitPAL: 768 x 576384 x 288 RGB 24 BitRGB 16, 24 bits, YUV422, YUV12WDM streaming class driver compatible with Direct Show & VFWTWAIN DriverOpen Utility SoftwareAdjustable 0.5 Mbps to 7.5 Mbps in 0.5 Mbps increments1.1 (USB 2.0 Compliant)PC with a Pentium Processor 600 MHz with MMX and 128MB of memoryUSB PortMicrosoft Windows 98, ME, 2000, XP32 bit VGA Display Adapter
MechanicalDimensions (WxHxD):
Lens:Lens mount:FOV:Focus Range:Zoom:Durability:
EnvironmentalAmbient Operating Temperature:Storage Temperature:Kit Power:
Base 10.5 x 3.2 x 11.5 in.(267 x 83 x 292 mm)Telescope pole 29 to 54 in. (737 to 1372 mm)(floor ~ center of camera)Camera w/ lights 6.3 x 3.5 x 4.5 in. (159 x 89 x 114 mm)F1.4 to 2.8, FL=4.0 to 64.0IntegratedH= 47° (wide), 3° (tele)Infinity~1.0m (tele) to 0.01m (wide)Optical to 16 x, Digital to 128 xZoom, Focus & Iris: more than 500Kcycles at room temperature
14° to 131° F (-10° C to 55° C)
-4° to 140° F (-20° C to 60° C)90 VAC to 240 VAC 50/60 HzAuto-sensing24 watts
Cre
dent
ial
Overview
Lenel offers several powerful and easy-to-use video recording options for a multitude of digital
video recorder and network video recorder applications. With flexibility to meet needs ranging from
high-resolution to expansive online storage, Video Recorders from Lenel present many affordable
options for those considering upgrading an existing analog installation to those looking for a fresh,
network-centric solution. Video Recorders are available in stand-alone or integrated deployments.
OnGuard GO! configurations provide powerful stand-alone systems for customers needing a DVR
or NVR application. Additionally, OnGuard GO! customers can add access control and ID badging
to the stand-alone video recorder without needing an additional server or database! No matter the
application, Video Recorders from Lenel offer a powerful opportunity to address a critical staple in
any security program.
Video Boards (DVB-408 & DVB-444)
Lenel offers two video boards, the DVB-408 and the DVB-444. Each board supports
industry-leading MPEG-4 recording compression. The affordable DVB-408 has eight channels of
capacity, while the DVB-444 has four channels and includes four on-board processors for more
efficient compression. Both board options give customers the ability to start and expand robust
video systems.
DVC-ST (4U)
The DVC-ST is a reliable, rack-mountable digital video recorder with several recording and storage
options. The DVC-ST supports analog video recording with up to two DVB-408s, or up to two
DVB-444s. Each DVC-ST has three hard drive bays for SATA, allowing customers to expand to
greater than one terabyte of online storage. The DVC-ST includes a 4U, 19-inch rack mount digital
storage recorder with Windows XP Professional, 10/100/1000 Ethernet, one 80 GB internal
OS-only hard drive (optional 3 additional data hard drives), DVD/CD ROM, 1.44 floppy and mouse.
DVC-EX (3U)
The DVC-EX is a high-powered machine offering the most expansive storage capacity of any DVR
available. With eight hard drive bays, the DVC-EX has capacity for four terabytes of online
storage. In addition to storage, the DVC-EX also allows the customer to configure RAID 5 data
redundancy. The DVC-EX includes a 3U, 19-inch rack mount digital storage recorder with
Windows XP Professional, 10/100/1000 Ethernet, one 80 GB OS-hard drive (optional data hard
drives, maximum of eight), DVD/CD ROM, 1.44 floppy, mouse and rack mount rail.
Video Recorders for OnGuard VideoManager™
51
DVC-ST Chassis (4U)
DVR / GO!
DVC-EX Chassis (3U)
DVR / NVR / GO!
Video
DVC-ES
The DVC-ES is an entry-level solution that is a great fit for small DVR applications. Available with a
single DVB-408, the DVC-ES comes in a tower form factor for easy placement in any security
office. It includes a tower chassis, digital storage recorder with Windows XP Professional,
10/100/1000 Ethernet, one 80 GB internal OS-only hard drive (optional 2 additional data hard
drives), CD ROM, 1.44 floppy and mouse.
DVC-1U
The DVC-1U is a powerful and easy to use Network Video Recorder (NVR) with a small footprint.
Occupying 1/4 to 1/3 the space of traditional video recorders, the 1U form factor can easily fit in
empty rack slots, rarely requiring additional racks to house it. The DVC-1U includes a 1U
rack-mount chassis, digital storage recorder with Windows XP Professional, two 10/100/1000
Ethernet ports, one 80 GB internal OS-only hard drive, one 500 GB internal Data Storage Drive
(optional 2 additional data hard drives), and CD/RW-DVD/R.
DVC-DELL
The DVC-DELL features a trusted hardware standard supporting an entry-level NVR application.
The Dell solution offers IT-centric security operations the ability to develop a video program using
a factory-tested server configuration that optimizes performance and ensures reliability.
Stand-alone Video Recorders - OnGuard GO! (DVC-ST, DVC-EX & DVC-1U)
Customers looking for stand-alone digital video recorders can use a Lenel video recorder with the
OnGuard GO! configurations. The stand-alone video recorder’s OnGuard GO! configuration has
the administration applications and database on the video recorder, saving money by not requiring
a separate security server to launch the most powerful security system available. Furthermore,
customers can take the single stand-alone video recorder and add OnGuard’s robust Access
Control, Fire & Intrusion and ID Management applications, as well as countless software options.
For customers expanding an existing analog environment by upgrading to a DVR or by embracing
IP by migrating to network video, Lenel video recorders offer the flexibility to initiate an integrated
security architecture by focusing on stand-alone digital video, then expanding the system when the
time is right.
DVC-ES Chassis
DVR
DVC-DELL
NVR / GO!
DVC-1U
NVR / GO!
52
Vide
o
ICT 220 DN Plus
Full D1 resolution with a true de-interlaced filter produces brilliant, artifact-free video. Using
state-of-the-art MPEG-4 (video) and synchronized ADPCM (audio) encoding, the ICT 220 provides
superior video quality and improved network performance. The ICT 220 outperforms the
competition, when compared to other network cameras using still picture encoding technology
such as MJPEG or Wavelet. The ICT 220 utilizes superior cross bit rate encoding technology, ixBR
Control®, to deliver powerful bandwidth control. Using ixBR, digital video streams more fluidly
because the data is encoded and streamed at a constant rate, yet it retains all the rich data of
variable bit rate encoding!
Key Features
■ 3 Axis MiniDome (360° horizontal x 90° vertical)
■ Powerful MPEG-4 video compression
• Supports up to 30 frames per second at full D1 resolution
■ True de-interlaced filter
■ Bidirectional G.711 and G.726 audio communication
■ Synchronized full-duplex one channel audio and video
■ State-of-the-art CPU, separate codec and embedded software
■ Intelligent bit rate control (flexible for difficult network environments)
■ Embedded streaming server and embedded Web server
■ Motion-detected and event-triggered alarm processing
■ Sensor-triggered recording and FTP:
• One (1) alarm input
• One (1) relay output
■ Supports a wide range of network protocols
■ 1/3 in. (8 mm) Sony Super HAD CCD
• 410K CCD Day-Night with IR cut filter varifocal lens
• 410K CCD standard varifocal lens
• 270K CCD fixed lens
■ True Day-Night capability
■ System time management
• RTC with Time Server synchronization
■ Security support:
• User authentication
• 128-bit encrypted data stream (selectable, for added security)
Fixed Dome Digital Network Camera
53
Video
ICT 220 DN Plus
54
Resolution ■ NTSC: 30 fps
■ PAL: 25 fps
RCA Analog Display CableRCA analog cable is for analog video output from camera module
inside of network camera. Use with handheld video monitor for quick
and easy focus and field of view setup. Connects to video output.
Power and Ethernet■ Power supply input voltage: 100~250 VAC 50-60 Hz
■ Power supply output voltage: 12 VAC @ 3.3 A
■ AC power cable capacity: 250 VAC, 10~16 A
■ Camera power input: 7~23V DC Max 8 Watts
■ Mid span PoE injector power input: 12V DC 1 Amp
■ Power supply connector type: N (male)
■ Ethernet: 10/100Base-T autosensing
Package Contents■ Camera
■ Power supply
■ Type N male power connector with leads
■ Single port mid span PoE injector
■ Power cords
■ CD-ROM with software & user guide
■ RCA analog display cable
■ Install template and mounting screws
Camera Dimensions■ 5.6 x 5 in. (142 mm x 128 mm)
Certifications■ UL
■ ULC
■ FCC
■ CE
■ CCC
■ RoHS
■ NTSC: 704x480 / 352x240 / 176x144
■ PAL: 704x576 / 352x288 / 176x144
Model – ICT220 DN Plus ( 410KCCD- Day-Night)
ICT2201DN
ICT2202DN
ICT2203DN
ICT2204DN
Model- ICT220S (410KCCD )
ICT2201S
ICT2202S
ICT2203S
ICT2204S
Region
Americas- Asia Pacific
Australia
UK
Europe
Part Number by Model and RegionModel- ICT220S ( 270KCCD )
ICT2201
ICT2202
ICT2203
ICT2204
Lens
Varifocal 4.0 – 9.0 mm F1.2
Varifocal 4.0 – 9.0 mm F1.2
Fixed 3.8 mm F2.0 manual focus
Minimum Illumination (Lux)
0.1Lux / f=1.4 (AGC 0n)
0.1Lux / f=1.4 (AGC 0n)
0.3Lux
Model
ICT220DN Plus
ICT220S
ICT220
Lens
Vide
o
ICT 230 DN Plus
Full D1 resolution with a true de-interlaced filter produces brilliant, artifact-free video. Using
state-of-the-art MPEG-4 (video) and synchronized ADPCM (audio) encoding, the ICT 230 provides
superior video quality and improved network performance. The ICT 230 outperforms the
competition, when compared to other network cameras using still picture encoding technology
such as MJPEG or Wavelet. The ICT 230 utilizes superior cross bit rate encoding technology, ixBR
Control®, to deliver powerful bandwidth control. Using ixBR, digital video streams more fluidly
because the data is encoded and streamed at a constant rate, yet it retains all the rich data of
variable bit rate encoding!
Key Features
■ Powerful MPEG-4 video compression
• Supports up to 30 frames per second at full D1 resolution
■ True de-interlaced filter
■ Bidirectional G.711 and G.726 audio communication
■ Synchronized full-duplex one channel audio and video
■ State-of-the-art CPU, separate codec and embedded software
■ Intelligent bit rate control (flexible for difficult network environments)
■ Embedded streaming server and embedded Web server
■ Motion-detected and event-triggered alarm processing
■ Sensor-triggered recording & FTP:
• One (1) alarm input
• One (1) relay output
■ Supports a wide range of network protocols
■ 1/3 in. (8 mm) Sony Super HAD CCD
• 410K CCD
• 270K CCD
■ True Day-Night capability
■ RoHS-compliant product
■ System time management
• RTC with Time Server synchronization
■ Security support:
• User authentication
• 128-bit encrypted data stream (selectable, for added security)
■ Lens not included
Digital Network Camera
55
Video
ICT 230 DN Plus
56
Resolution ■ NTSC: 30 fps
■ PAL: 25 fps
■ NTSC: 704x480 / 352x240 / 176x144
■ PAL: 704x576 / 352x288 / 176x144
■ Minimum Illumination 0.1 LUX / F=1.4 (AGC-on)
Certifications■ UL
■ ULC
■ FCC
■ CE
■ CCC
■ RoHS
Environment■ Recommendation: For indoor use unless in housing
Temperature
■ 41~122 °F (5~50 °C) Optimum
■ 21~65 °F (-4~140 °C) Endurable
Humidity
■ 8~80% RH Optimum
■ 0~90% RH Endurable
Power and Ethernet■ Power supply input voltage: 100~250 VAC 50-60 Hz
■ Power supply output voltage: 12 VAC @ 3.3 A
■ AC power cable capacity: 250 VAC, 10~16 A
■ Camera power input: 7~23V DC Max 8 Watts
■ Mid span PoE injector power input: 12V DC 1 Amp
■ Power supply connector type: N (male)
■ Ethernet: 10/100Base-T autosensing
Package Contents■ Camera
■ Power supply
■ Single port mid span POE injector
■ Power cords
■ CD-ROM with software and user guide
■ Mounting stand
■ Type N Power connector with leads
Camera Dimensions (without lens)■ 5.3 x 2.4 x 2.2 in. (135 x 60 x 57 mm)
Model – ICT230 DN ( 410KCCD- Day-Night)
ICT2201DN
ICT2202DN
ICT2203DN
ICT2204DN
Model- ICT230S ( 270KCCD )
ICT2201S
ICT2202S
ICT2203S
ICT2204S
Region
Americas- Asia Pacific
Australia
UK
Europe
Part Number by Model and Region
Vide
o
ICT 240 DN
The ICT 240 is a full-featured IP speed dome that delivers the best of both worlds: performance
and affordability. This outdoor speed dome provides full D1 resolution (704X480 NTSC, 704X576
PAL) with a true de-interlaced filter that produces immaculate video. Stealth Spin Technology®
uses precisely machined gears, delivering unmatched smooth and accurate movement for virtually
silent operation. Using state-of-the-art MPEG-4 (video) and synchronized ADPCM (audio)
encoding, the ICT 240 provides superior video quality and improved network performance. The
ICT 240 outperforms the competition, when compared to other network cameras using still picture
encoding technology such as MJPEG or Wavelet. The ICT 240 uses ixBR® superior cross bit rate
encoding technology. Using ixBR, digital video streams more fluidly because the data is encoded
and streamed at a constant rate, yet it retains all the data of variable bit rate encoding!
Built for maximum long-life performance, the ICT 240 deploys a high-quality slip-ring, tested for
over 20 million spins!
Key Features
■ Extremely silent, outdoor speed dome IP camera
■ 1/4 in. Sony Ex-view CCD
■ Filter changeable type day and night
■ IP66 water-resistant
■ 26X optical with 12X digital zoom (selectable)
• Optional: 18X optical with 12X digital zoom
■ State-of-the-art CPU, codec and embedded software
■ Superior video compression – MPEG-4
■ Maximum 30 frames per second at D1 resolution with de-interlaced filter
■ Bidirectional audio communication – up (ADPCM), down (PCM)
■ Synchronized one channel audio and video data transmission
■ Intelligent bit rate control for flexible network deployment
■ Enhanced image quality
■ MPEG-4
■ Embedded streaming server and embedded Web server
■ Motion-detected and event-triggered alarm processing
■ Easy recording and playback on client PC
■ Sensor-triggered
• Four (4) alarm inputs
• Two (2) relay outputs
■ Auto-flip video – on/off configuration
■ Wide range of network protocols supported
■ System time management
• RTC with Time Server synchronization
■ Security support
• User authentication
• 128-bit encrypted streaming data for additional security (selectable)
Outdoor IP Digital Speed Dome
57
Video
ICT 240 DN
58
Resolution■ NTSC: 30 fps
■ PAL: 25 fps
■ NTSC: 768x494
■ PAL: 752x582
■ Horizontal Resolution: >480 TVL
Certifications■ UL
■ FCC
■ CE
■ CCC
■ RoHS
■ ULC
EnvironmentTemperature
■ 41~60 °F (5~50 °C) Optimum
■ -4~140 °F (-20~60 °C) Endurable
Humidity
■ 8~80% RH Optimum
■ 0~90% RH Endurable
Video Quality■ Minimum luminance – Normal: 0.7 lux
■ Minimum luminance – Night Mode: 0.1 lux
■ Day-Night ICR: Auto/Day/Night
■ Luminance Signal-to-Noise Ratio: >50 dB
■ BLC: On/Off
Lens■ f1.6~3.8 f3.5-91.0 mm
■ Minimum video distance: .32 m (w) / 4.92 ft. (1.5 m) telephoto
Power and Ethernet■ PS input voltage: 100~250 VAC 50-60 Hz
■ PS output : 18-32 VAC @ 1.3 A
■ AC power cable: 250 VAC, 10~16 A
■ Power consumption: 24 watts maximum
■ Ethernet: 100Base-T
Package Contents■ Camera
■ External housing (IP66)
■ Wall mount and hardware
■ CD-ROM with Software & User Guide
■ Quick Installation Guide
Weight■ 5 lbs (1.9 kg)
Pan Tilt■ Pan: 350° per second continuous rotation
■ Tilt Rotation: 0-90°
■ Accuracy: 0.024°
Privacy Zones and Sectors■ 24 programmable zones
■ 8 programmable sector patternsVi
deo
ICT 250 DN
The ICT 250 is a full-featured IP speed dome that delivers the best of both worlds: performance
and affordability. This indoor speed dome provides full D1 resolution (704X480 NTSC, 704X576
PAL) with a true de-interlaced filter that produces immaculate video. Stealth Spin Technology®
uses precisely machined gears, delivering unmatched smooth and accurate movement for virtually
silent operation. Using state-of-the-art MPEG-4 (video) and synchronized ADPCM (audio)
encoding, the ICT 250 provides superior video quality and improved network performance. The
ICT 250 outperforms the competition, when compared to other network cameras using still picture
encoding technology such as MJPEG or Wavelet. The ICT 250 uses ixBR® superior cross bit rate
encoding technology. Using ixBR, digital video streams more fluidly because the data is encoded
and streamed at a constant rate, yet it retains all the data of variable bit rate encoding!
Built for maximum long-life performance, the ICT 250 deploys a high-quality slip-ring, tested for
over 20 million spins!
Key Features
■ Stealth Spin Rotation technology
■ 1/4 in. Sony Ex-view CCD
■ Filter changeable type day and night
■ 26X optical with 12X digital zoom (selectable)
• Optional 18X optical zoom with 12X digital zoom
■ State-of-the-art CPU, codec and embedded software
■ Superior video compression – MPEG-4
■ Maximum 30 frames per second at D1 resolution with de-interlaced filter
■ Bidirectional audio communication – up (ADPCM), down (PCM)
■ Synchronized one channel audio and video data transmission
■ Intelligent bit rate control for flexible network deployment
■ Enhanced image quality
■ MPEG-4
■ Embedded streaming server and embedded Web server
■ Motion-detected and event-triggered alarm processing
■ Easy recording and playback on client PC
■ Sensor-triggered
• Four (4) alarm inputs
• Two (2) relay outputs
■ Auto-flip video – on/off configuration
■ Wide range of network protocols supported
■ System time management
• RTC with Time Server synchronization
■ Security support
• User authentication
• 128-bit encrypted streaming data for additional security (selectable)
Indoor IP Digital Speed Dome
59
Video
ICT 250 DN
60
Resolution■ NTSC: 30 fps
■ PAL: 25 fps
■ NTSC: 768x494
■ PAL: 752x582
■ Horizontal resolution: >480 TVL
Certifications■ UL
■ FCC
■ CE
■ CCC
■ RoHS
■ ULC
EnvironmentTemperature
■ 41~122 °F (5~50 °C ) Optimum
■ -4~140 °F (-20~60 °C) Endurable
Humidity
■ 8~80% RH Optimum
■ 0~90% RH Endurable
Video Quality■ Minimum luminance – Normal: 0.7 lux
■ Minimum luminance – Night Mode: 0.1 lux
■ Day-Night ICR: Auto/Day-Night
■ Luminance Signal-to-Noise Ratio: >50 dB
■ BLC: On/Off
Lens■ f1.6~3.8 f3.5-91.0 mm
■ Minimum video distance: .32 m (w) / 4.92 ft. (1.5 m) telephoto
Power and Ethernet■ PS input voltage: 100~250 VAC 50-60 Hz
■ PS output : 18-32 VAC @ 1.3 A
■ AC power cable: 250 VAC, 10~16 A
■ Power consumption: 24 watts maximum
■ Ethernet: 100Base-T
Package Contents■ Camera
■ Ceiling mount bracket and cover
■ CD-ROM with Software & User Guide
Weight■ 5 lbs (1.9 kg)
Pan Tilt■ Pan: 350° per second continuous rotation
■ Tilt rotation: 0-90°
■ Accuracy: 0.024°
Privacy Zones and Sectors■ 24 programmable zones
■ 8 programmable sector patternsVi
deo
ICT 510 Video Server
The ICT 510 single channel audio/video server supports full D1 resolution coupled with a true
de-interlaced filter to produce brilliant, artifact-free video. Owing to state-of-the-art MPEG-4 (video)
and synchronized ADPCM (audio) encoding, the ICT 510 provides superior video quality and
improved network performance. The ICT 510 outperforms the competition, when compared with
other audio video server using still picture encoding technology such as MJPEG or Wavelet. The
ICT 510 provides superior cross bit rate encoding technology, ixBR Control®, which delivers
powerful bandwidth control. Using ixBR, digital video streams more fluidly because the data is
encoded and streamed at a constant rate, yet it retains all the rich data of variable bit rate
encoding!
Key Features
■ MPEG-4 video compression
■ Supports video frame rates of up to 30 fps
■ Full D1 resolution with de-interlaced filter
■ Bidirectional G7.11 audio communication
■ Synchronized one channel audio and video data transmission
■ Intelligent bit rate control for various network environments
■ Enhanced image quality
■ MPEG-4 and JPEG dual streaming for mobile network
■ Embedded streaming server
■ Embedded Web server
■ Motion-detected and event-triggered alarm processing
■ Remote PTZ control via RS-485
■ Sensor-triggered one alarm input and one relay output
■ Wide range of network protocols supported
■ System time management
• RTC with Time Server synchronization
■ Security support
• User authentication
• Encrypted streaming data for additional security (selectable)
Single Channel AV Server
61
Video
ICT 510 Video Server
62
Resolution■ NTSC: 30 fps
■ PAL: 25 fps
■ NTSC: 704x480, 356x240, 176x120
■ PAL: 704x576, 352x288, 176x144
Certifications■ UL
■ FCC
■ CE
■ CCC
■ RoHS
■ ULC
Environment (indoor use only)Temperature
■ 41~122 °F (5~50 °C) Optimum
■ -4~140 °F (-20~60 °C) Endurable
Humidity
■ 8~80% RH Optimum
■ 0~90% RH Endurable
Power and Ethernet■ PS input voltage: 100~250 VAC 50-60 Hz
■ PS output : +12 V @ 1.3 A
■ Server input: 7~23 VAC
■ AC power cable: 250 VAC, 10~16 A
■ Power consumption: 8 watts maximum
■ Ethernet: 10/100Base-T autosensing
Package Contents■ Server
■ Regional specific power supply
■ Power cords
■ CD-ROM with Software & User Guide
■ Mid span POE injector
■ Type N Power connector with leads
PC Requirement Remote Viewing (minimum) ■ P-4 1.2 GHz Processor
■ 256 MB RAM
■ Windows 2000, Windows XP Professional / Home
■ IE 5.5
■ Video monitor minimum resolution: 1024 x 768
■ Ethernet: 100Base-T
Vide
o
63
Corporate Headquarters
1212 Pittsford-Victor RoadPittsford, NY 14534-3820TEL: 585.248.9720FAX: 585.248.9185
United Kingdom Office & Training Center
95 Maybury RoadWoking, SurreyGU21 5JL UKTEL: +44.1483.815230FAX: +44.1483.815231
Hong Kong Office & Training Center
Room 1401-2, 14/FChinachem Johnston Plaza178-186 Johnston PlazaWanchai, Hong Kong, SAR, ChinaTEL: +852.2893.2886FAX: +852.2893.7373
Dubai Office & Training Center
Building 5EB - Office 550Dubai Airport Free ZoneDubai, UAETEL: +971.4.609.1019FAX: +971.4.609.1021
Middle East Office & Training Center
Assaydeh Center, Main RoadMansourieh, Al MatnLebanonTEL: +961.4.409184FAX: +961.4.409569
Lenel Systems International is a leading provider of software and turnkey security systems for corporate and government markets. We focus on developing products that enable organizations to effectively protect and manage their people, property and assets by maximizing IT and infrastructure investments.
When we launched the OnGuard integrated solution in 1995, our pioneering efforts brought the power of leading-edge technology, the reliability of software industry standards, and the flexibility of open systems architecture to a historically proprietary security market. We swiftly moved to a leadership position by developing and delivering business solutions that protect people, property and assets. Today we are recognized as the global leader and de facto standard in software and integrated systems for commercial and government security markets.
With nearly 15,000 system installations in 90 countries worldwide, we boast a blue chip customer base with a strong presence in a broad range of vertical markets. We have earned numerous awards for technology innovation, growth, market leadership and customer satisfaction. Lenel is part of UTC Fire & Security, a business unit of United Technologies Corp. (NYSE:UTX).
Lenel’s world headquarters are located in Rochester, New York. We also have major operational centers in London, Hong Kong, Beirut and Dubai, numerous satellite offices, and sales and support coverage worldwide.
64
Contact Information
www.lenel.com Lenel Systems International, Inc.1212 Pittsford-Victor RoadPittsford, New York 14534 USATel 585.248.9720 Fax 585.248.9185www.lenel.com
© 2007 Lenel Systems International, Inc.
Lenel is a global leader in the development and delivery of scalable, integrated systems for
the commercial security market, with over 15,000 system implementations in more than 90
countries. Lenel is headquartered in Rochester, N.Y. USA, with sales and support coverage
in all major world markets. Lenel is part of UTC Fire & Security, a $4.7 billion company that
provides fire safety and security solutions to more than one million customers worldwide.
Headquartered in Connecticut, UTC Fire & Security is a business unit of United Technologies
Corp., which provides high technology products and services to the building and aerospace
industries worldwide. More information about Lenel and UTC Fire & Security can be found on
their Web sites at http://www.lenel.com and http://www.utcfireandsecurity.com.
The possibilities are endless.