led t8 glass tubefiles/specsheets/ge… · · if led tube can be compatible with existing ballast:...
TRANSCRIPT
Features
LED T8 Glass tube
Electrical and Photometric Characteristics
Input voltage: depends on ballast or AC120-277VOperating frequency: 50/60HzPower factor: ≥ 0.90Ambient temperature range: -20°C ...+45°CMain materials: glassColor Temp: 3000K,3500K,4000K,4500K,5000K
08≥:IRCBeam angle: >220°Dimmable:THD: <20%Base type: G13IP Rating: IP20
No
VER#:V1.417-07-07
5YEAR
WARRANTY
* Exceeding maximum ratings for operating temperature and input voltagewill reduce expected life time or destroy the product.All data subject to change without notice. Errors and omission excepted. Always make sure to use the most recent release.
®
Product informationThe LED T8 Glass Tube is approved by UL (Dual Mode, Type A and Type B) , CUL,FCC and DLC 4.0. It can operate on electronic ballasts as Type A, or be used without ballasts as Type B. Directly replacement for 17W/24T8 and 32W/48T8 fluorescent lamps. it widely been used in commercial buildings,such as super market, factories,hotels,conference rooms,schools,and office buildings.
· Plug and Play as Type A, no need rewire.· Or direct AC input as Type B, bypass the existing ballast.· High efficiency : 100-130LPW· Energy saving: up to 70%· Eco-friendly: no UV or IR radiation, mercury free,no flickering· Safe transportation: Reliable strong package.· 50,000 Hrs lifetime, 5 years warranty.UL/CUL/FCC/DLC 4.0 listed.
Store and use the lamps as same as standard fluorescent lamps
Switch off mains supply before installing/removing lamp
Use in fully enclosed fixtures may affect life performance
Due to the special conditions of the manufacturing processes of LED,the typical data of technical parameters can only refect statistical figures anddo not necessarily correspond to the actual parameters of each single product which could differ from the typical value.
Operation and Maintenance Tips
SpecificationsRate
Wattage Length (ft)
CCT(Kelvin)
Rated Luminous
flux (lm)CRI(Ra)
Pack Qty (Pcs)
LED T8 glass tube
10 2 4000K 1507 5208>
12 4 4000K 1786 >80
15 4 4000K 2157 >80
18 4 4000K 2447 >80
20 4 4000K 2628 >80
Dimension Diagram
ItemNumber
Beam angleHousing
SYH-GL08-AB0610
SYH-GL08-AB1212
SYH-GL08-AB1218
SYH-GL08-AB1220
SYH-GL08-AB1215
25
25
25
25
> 220°
> 220°
> 220°
> 220°
> 220°
Glass
Glass
Glass
Glass
Glass
•Lamps should be kept free from contamination.•
•Good condition of the lamp-holder contacts is important to ensure proper operation of lamp.•For direct wire please check the provided installation instructions•
• Not for use in emergency lighting circuits
)eergeD()W(
* All data are related to the entire product
For technical information of other CCT, please contact our sales representative.
Maximum overall length (mm) 4ft
8911A
5.82D
2ft
588B 1205595
28.5
C 1213603
Notes:All item unmber are UL,CUL,FCC,certificated
Package
Installation Diagram
ItemNumber
SYH-GL08-AB0610SYH-GL08-AB1212SYH-GL08-AB1215SYH-GL08-AB1218
Qty/Carton(Pcs)
Net Weight(Kg)
Gross Weight(Kg)
Size of CartonLxWxH (mm)
0221BA-80LG-HYS
Pcs in 1*40’ HQ
4. Verify the existing ballast is on our ballast list or not.· If led tube can be compatible with existing ballast:
· Turn on power and check the light distribution.
· If LED tube can’t be work with existing ballast or the ballast is dead:
· Remove the existing ballast and rewire as AC 100-277V input
· Turn on the power and check the light distribution.
* Note: the above quantity full a container based on tubes pack In foam holders+outer carton and without pallets.
Pcs in 1*20’ GP
AC-120-277V
25
25
3.8777
625x195x1951235x195x1951235x195x1951235x195x195
5.755.755.75
25
56250287002870028700
27075138251382513825
25 3.2
25 71235x195x195 5.75 2870013825
Modifications to the product avoid the warranty.
1. Swich off the power before replacement.2. Remove diffuser(if needed).3. Remove the existing fluorescent lamp.
· Plug T8LED tube into lamp holders of existing fixture· Put on diffuser(if removed in step 2)
· A qualified electrician needed
· Put onLED tube into the lamp holders of existing fixture· Put on the cover diffuser (if needed)