www.tunascs.com

LED Emergency Device Model: LED EMG L12S 8015NS-HB With Ni-Cad 12V 3000mAh

Product Description: Consisting of module and battery pack designed to fit LED luminaires and convert them to stand –by lighting units in case of mains failures. It is compatible for use with constant current led driver.

In the event of a mains failures, the converted luminaires will remain illuminated for the rated duration of 1 hours (minimum). The luminaires will resume normal operation and the battery will be recharged upon resumption of the mains supply.

The charger/inverter module conforms to : o Electromagnetic Compatibility Directive (89/336/EEC)" o And "Low Voltage Directive(73/23/EEC)" Product Features a. Operate 80W constant for LED High Bay b. Complete with Ni cad Battery c. Constant current LED emergency module d. Duration in emergency mode 1 hours e. Time for full recharge of the battery 24 hours f. Lumen factor 0,75

Standards Installation a. Supply voltage 220-240V, +5/-5%, 50/60Hz b. Voltage Neutral & Grounding < 2 Volt c. Line emergency standby 24 hours d. Line emergency and line of lamp on the same phase Product highlights 1. According to EN60598; EN 55015; CE; ROHS 2. Deep discharge protection Specification Voltage : AC 220-240 V 50-60 Hz Current : 0.07 A Rate power : 5 W Battery charging : 24 hours Charging current : 200MA Discharge current : 2.70A Suitable light source : LED High Bay Battery specification : Ni-Cd 12V 3000 MAh HT (High temperature) Environment temperature : -10…+55 °C Highest surface temperature : 70 °C LED charge monitoring Test switch : Switch between emergency and normal lighting function, should have normally

open switch.

1

Material and Finishing Iron with spray painting

Januari 2016

www.tunascs.com

Dimension Drawing

1. Inverter Device

2. Ni-Cad Battery

Application guide: Install the unit according to wiring diagram, any improper wiring may lead to permanent damage

to the unit; Normal AC mains supply, the inverter allows the battery pack charging, trickle charge to maintain

battery performance. Sudden interruption of the mains AC, then the inverter converts DC battery powered to ensure that lighting and security;

Inverter with multiple protection functions: charge protection, discharge protection, short circuit protection;

To ensure maximum performance of the built-in battery, please fully charge the unit for 24 hours after first installation; To extend battery life, please make sure charge the battery at least one time every three months;

Don’t install top of the high temperature objects. Please ensure that the operating ambient temperature is below 50°C, and maximum case temperature (tc) not exceeding 70°C;

Do not operate this unit beyond the operating supply range; In normal use, the battery can be done 500 charge/discharge cycles; Inverter life is more than 2 years; If experience any problem during use, please contact with supplier for help;

2

52 m

m

246 mm 100 ± 3 mm

Red

Black

285 ± 3 mm

27 m

m

255 ± 3 mm

20 m

m

30 m

m

156 ± 2 mm

172 mm

40 m

m

www.tunascs.com

Connection Drawing Diagram Wiring For LED High Bay

WARNING: 1. Apabila akan mengaplikasikan ke LED High Bay harap konfirmasi dulu ke supplayer mengenai

compatible atau tidaknya, kerusakan yang di sebabkan karena “simulasi sendiri” bukan menjadi tanggung jawab TCS.

2. Wiring harus mengikuti diagram di atas. 3. Kesalahan wiring bisa mengakibatkan kerusakan total pada Inverter maupun Lampu LED yang di

wiring. 4. Kerusakan yang di sebabkan karena kesalahan wiring yang tidak sesuai dengan diagram di atas

bukan menjadi tanggung jawab TCS. 5. Wiring Battery untuk LED High Bay sebenarnya tidak mengikuti standard “Vendor Lighting”

karena seharusnya Output Driver harus langsung masuk ke LED. Dengan ini TCS menyatakan tidak bertanggung jawab ketika lampu High Bay LED yang di aplikasikan dengan battery akan kehilangan status garansi dari “Vendor Lighting”.

3

L (emergency)

L (swith)

N (neutral)

G (Earth)

LED High Bay

Driver Input Output Input

- + +

-

3