TOSHIBA1

2385xxA 1/4

40 to 140 mm O.D. 160 to 315 mm O.D.

TECHNICAL SPECIFICATIONS

SR5 DIAMANT

coupling with full end load retentionfor PE pipes to EN 12201for uPVC pipes to EN 145240 to 315 mm outside diameter

Body : cast iron to EN 1561ductile iron to EN 1563

Flanges : ductile iron to EN 1563Gasket : rubber to EN 681-1

fluid temperature below 40°CGripping ring : brass ring to EN 1216X from O.D.40 up to O.D.63

brass ring to EN 1982 from O.D.75 up to O.D.315Bolts : standard : galvanised and bichromated steel - NF E 25-032

alternative : A2(304) stainless steel treated against gallingCoating : epoxy, average thickness of 250 microns

Fitting without inside limit stop allowing to joint PE or uPVC pipe of same outsidediameter.Tightness and end-load retention:from O.D.40 up to O.D.140 - gasket with built-in gripping ring operatingsimultaneously to ensure fitting end-load retention and tightness.(patented concept)from O.D.160 up to O.D.315 - profiled gasket and tapered gripping ring operatingone after another to ensure fitting end-load retention and tightness.Maximum assembly safety thanks to a long pipe fitment.please see table - ( E )Ready assembled fitting. Fitment ensured without specific tools.Tightening torque checking with torque wrench.Angularity of one pipe with the other allowed up to 6°.

Allowable operating pressure : 16 Bar

PE uPVC- Pressure and pulling out resistance test on free end testing assembly : 20 bar 25 bar- Pressure resistance test on locked end testing assembly : 25 bar 25 bar

Testing time : 1 hour at 20°C temperature at the recommended tighteningtorque as shown in the assembly leaflet

- Test certificates made according to standards in force are available on request.

GASKETS AND GRIPPING RINGS DETAILS

PRINCIPAL CHARACTERISTICS

gripping ring

rubber gasket

gripping ring

rubber gasket

40 to 140 mm O.D.

160 to 315 mm O.D.

04.5009 I04.5009 04 001x21M 2 54 801 811 011,1

05.5009 I05.5009 05 001x21M 2 84 011 031 003,1

36.5009 I36.5009 36 011x21M 2 35 811 151 079,1

57.5009 I57.5009 57 031x41M 2 17 831 161 055,2

09.5009 I09.5009 09 051x21M 4 98 851 871 025,3

011.5009 I011.5009 011 081x21M 4 201 471 002 005,4

521.5009 I521.5009 521 031x41M 4 17 061 332 015,4

041.5009 I041.5009 041 041x41M 4 57 041 332 089,4

061.5009 I061.5009 061 052x41M 4 08 382 062 013,01

081.5009 I081.5009 081 56x61M 4 371 382 372 043,7

002.5009 I002.5009 002 003x61M 4 39 913 813 097,41

522.5009 I522.5009 522 003x61M 4 601 823 823 003,02

052.5009 I052.5009 052 003x61M 6 801 833 953 050,02

513.5009 I513.5009 513 003x61M 6 801 043 624 027,92

The technical evolution of our products may lead to modifications without prior notice

PRODUCT CODE WEIGHT(kg)

L(mm)

E(mm)

H(mm)

stainless steel screwsstandard screws

PIPEO.D. (mm)

BOLTSquantitydimension

L

HE

L

H

E

Couplings "DIAMANT" SR5 with full end load retention for potable water distribution network pipes maybe used without stiffening insert

- on P.E. 80 polyethylene pipe, 12.5 Bar nominal pressure, SDR 11 to EN 12201- on P.E. 80 polyethylene pipe, 16 Bar nominal pressure, SDR 9 to EN 12201- on uPVC pipe to EN 1452.

Please refer to assembly leaflet for fitment care.

* For other applications, please contact us

NOVEMBER 2006

SR5 DIAMANT

9005-4-E

max. outline

max. outline

40 to140 mm O.D. 160 to 315 mm O.D.