lcn automatic operators · lcn automatic operators senior swing 9530 senior swing 9540 senior swing...

LCN AUTOMATIC OPERATORS

SENIOR SWING 9530

SENIOR SWING 9540

SENIOR SWING 9550

SENIOR SWING 9560

8310 ACCESSORIES

PHONE 800-526-2400FAX 800-248-1460www.lcn.ingersollrand.com8/0753

LCN CLOSERS121 W. RAILROAD AVE.P.O. BOX 100PRINCETON, IL, USA 61356-0100

LCN ELECTROMECHANICAL POWERED SYSTEMSELECTROMECHANICAL AUTOMATIC OPERATORSLCN’s electromechanical products are designed primarily forautomatic opening applications that occasionally requiremanual opening. A control box provides all electricalfunctions. These self-contained units are suitable for use onsingle leaf doors or pair of doors. These products combine allthe control and power elements into a single operator package,only some actuators are required to complete the system.

Surface mounted and overhead concealed mountingsavailable.Available in two standard anodized finishes – aluminumand dark bronze. Custom anodized finishes and custompaint is available.

LOW ENERGY ELECTROMECHANICAL POWER OPERATORSComplies with ANSI 156.19Opening time from full close to backcheck is no faster than3 secondsLess than 15lbs of force to open door manually

HIGH ENERGY ELECTROMECHANICAL POWEROPERATORSComplies with ANSI 156.10Opening time from full close to backcheck is no faster than1.5 secondsLess than 30 lbs of force to open door manuallyRequires use of guide rails and safety devices

STANDARDS, LISTINGS & APPROVALS UL listed for self-closing doors without hold open. UL 325.Tested and certified under ANSI.Low Energy Electromechanical Operators ANSI 156.19High Energy Electromechanical Operators ANSI 156.10ADA Compliant. Applicable to Low Energy Electromechanical Operators only.Wiring is compliant with both UL 325 and the NEC.Separation of high and low voltage.Consult the factory for other listings.

WARRANTY2 year limited warranty. See General Section forcomplete details

MAINTENANCELow Energy Electromechanical Power Operators

Operators mounted according to the LCN Installationinstructions require no periodic maintenance oradjustments. Monthly, quarterly and annual visual inspections arerecommended.No service contracts.

High Energy Electromechanical Power OperatorsHigh energy automatic operators may require periodicmaintenance and/or adjustments.Daily visual inspections are recommended to ensureproper operation of all activation and safety devices.



LCN ELECTROMECHANICAL POWERED SYSTEMSGENERAL ELECTRICAL DATA1. Input power 115 volt, 3 wire, single phase, 60Hz, fused, 15 amp supply.2. UL approved type flexible conduit is recommended for the 115 volt power line.3. The 115 volt power supply must be a dedicated circuit from the main circuit breaker panel and must not be

connected into a building lighting system operating fluorescent lights.4. Location of conduits determined by mounting. See installation instructions for location.

2500, 2800, 2900, 9300, 9500, 9700 SeriesELECTRICAL DATA1. 120 VAC input @ 2.5 amps (2500 and 9300 Series).2. 120 VAC input @ 2.5 amps (2800, 2900,9500 and 9700 Series).3. 24 V AC output @ 1.5 amps (protected by self-resetting thermal fuse).4. 24 V DC available with SO kit included.9100 SeriesELECTRICAL DATA1. 120 VAC input @ 1 amp. 2. 17 VAC output @ 2.5 amps on premium control box.3. 24 VDC available with SO kit included with premium control box.


thenderson

Highlight

thenderson

Highlight

thenderson

Highlight

thenderson

Highlight

thenderson

Highlight

thenderson

Highlight




LCN ELECTROMECHANICAL POWERED SYSTEMS

SINGLE DOOR SYSTEM (Low Energy)An Interior Door.No guide rails or safety devices.Free Swinging (or Dogged) Door.

How It Works

Wireless RF actuators with receiver, powered by thetransformer allows for easy installation. For automaticdoor operation, touching either actuator signals thereceiver and power operator to open the door to 90degrees. The door is held there until the system timesout. Door closes via spring return. Door opening speed,closing speed and hold open time is adjustable on thecontrol box. If not actuated, the power operatorfunctions as a manual door.

120VInput

Low Voltage Wiring

RF Receiver

RF Actuator

RF Actuator

Automatic Operator

SINGLE DOOR SYSTEMS

VESTIBULE ENTRY SYSTEM (Low Energy)

Exterior & Vestibule doors.

Sequential Operation.

No guide rails or safety devices.Controlled Access, Free Egress.

How It Works

This installation provides both accessibility and securityfor building occupants. It allows for the integration ofmultiple automatic operators, a card reader and electricstrike. A sequencer allows sequential operation of thetwo automatic operators. Vestibule actuators allowsingle door ingress/egress from the vestibule asneeded. If not actuated the power operator functionsas a manual door.

Low Voltage Wiring

Wall Plate Actuator

Automatic Operator

Automatic Operator

Card Reader w/keypad as Exterior Actuator

Sequencer

Electric Strike

Low Voltage

Wall Plate Actuator

Wall Plate Actuator

Note: 120V AC Input required to both operators

120V Input

120V Input

VESTIBULE ENTRY OPERATION

BILL OF MATERIALSQty. Part No. Description1 9542 Automatic operator (RH)1 9531 Automatic operator (RH)3 8310-853 Wall Plate Actuators1 8310-849 Sequencer

Other products from Von Duprin and Locknetics

BILL OF MATERIALSQty. Part No. Description1 9531 Automatic Operator (RH)2 8310-3853WS RF Actuators1 8310-865 RF Receiver

This page illustrates examples of typical Electromechanical LCN systems. Pleaseconsult your local SSC representative of LCN for assistance with specificinstallations and material requirements.

thenderson

Line

thenderson

Line

thenderson

Line



LCN 9530 SERIES

STANDARD ANODIZED

CUSTOMANODIZED

CUSTOMPAIN

T

FINISH HANDING

HANDED

NON-HANDED

COVER

METAL

ARM FUNCTION

STANDARD (SIN

GLE)

REGULAR (D

OUBLE)

OFFSET PIVOT ARM

CENTER PIVOT ARM

DOUBLEEGRESS (PUSH/PULL

)

MOUNTING

SURFACE MOUNT SIN

GLEDOOR

SURFACE MOUNT SIM

ULTANEOUS PAIR

SURFACE MOUNT IN

DEPENDENT PAIR

CONCEALED SIN

GLEDOOR

CONCEALED IN

DEPENDENT PAIR

CONCEALED SIM

ULTANEOUS PAIR

The 9530 SENIOR SWING by LCN is anADA door operator that is a two-in-one swing door operator. SENIORSWING operators when activated,opens doors automatically forwheelchair access, yet allows formanual operation for regularpedestrian traffic.

Push ‘N Go permits non-switchactivationPower Boost provides additionallatching forceElectromechanical unit withmicroprocessor controlDigital keypad for easy setupMeets International Building Coderequirements and ANSI A156.19UL approved for fire doors

9530 Series is fully compliant with UL325 & UL 1998 and meets theprovisions of ANSI A156.19. The 9530Series is UL listed for fire-ratedapplications. The 9530 Series alsomeets the provisions of the Americanswith Disabilities Act.

9530 series operator is shipped with motor gearbox, control box,standard arm, header, and mounting hardware. Actuators availableseparately, see pages 121.

Single door, surface mounted.

Meets ADA requirements (power mode only).

Handed product.

36” header length is standard. Specify length 33” to 49” max.

Double door header available up to 98”, specify other length 49” to 98”max. Consult factory regarding this option.

Adjustable hold open period of 1 to 32 seconds in automatic or manualmode.

SINGLE DOOR, SURFACE MOUNT (PULL)OFFSET PIVOT/BUTT HINGE FEA

TURE

S



Butt Hinges should not exceed 5” (127 mm) in width.

Reveal should not exceed 4” (102 mm).

Head Frame minimum 1 3/4” (44 mm). Face frame 6 3/4” (171 mm)total operator clearance.

Top Rail minimum 2 3/4” (70 mm).

Opening & Closing Time are variable by adjustments to the electroniccontrol box. Maximum hold open time adjustable up to approximately32 seconds.

System Diagram see “AUTOMATIC OPERATORS” section pages 52-54for typical system wiring and page 55 for electrical data.

Please consult your local SSC representative or LCN for assistance withspecific installations and material requirements.

TOP JAMB SINGLE DOOR(OFFSET PIVOT/BUTT HINGE,CENTER PIVOT, PULL)MOUNTING

HOLLOW METAL FRAMESuggested Installation

MAXIMUM OPENINGTemplate allows 90 degree poweropening and 90 degree manualopening.

LCN 9530 SERIES

PULL ARM ASS'Y

OFFSET PIVOT

or BUTT

HINGES

2 3/4

"70 MM

SWING OPERATOR

48" DOOR OPENING (MAX.)

INCOMING

LEFT HAND

PULL CHANEL

1 3/4

"44 MM

SWING OPERATOR

4 1/2

"114 MM

6 3/4

"171 MM

5 3/4

"146 MM

DOOR

SWING DIRECTION

INTERIOR

PULL CHANEL

PULL ARM ASS'Y

1"25 MM

1 15/16

"49 MM

17

3/8

" 11

1/2

"292 MM

Special TemplatesCustomized installation templates or products may be available to solve unusual applications. Contact LCN for assistance.

MOUN

TINGD

ETAILS



LCN 9530 SERIES MOTOR GEARBOXMOTOR GEARBOX (STANDARD FORCE) –SENIOR SWING, 9530-3454Driving mechanism for operator. Provides 15lbs opening force.Handed.

MOUNTING BRACKETMOUNTING BRACKET – 2 3/4”, 9530-275Motor gearbox mounting bracket for 2 3/4" offset pivot or butt hingeinstallations. Front bracket.

REAR MOUNT BRACKET, 9530-3018Motor gearbox mounting bracket. Rear bracket.

ANGLED BRACKET, 9530-334-1Mounting bracket for surface applications.

CONTROL BOXESCONTROL BOX – SENIOR SWING, 9530-3462Electronic controlling device for Senior Swing.

HEADERSHeader, 9530-3572HLStandard, mounting header. Single door, single operator.Specify length 30”to 49” maximum.

Header, 9530-3572DDStandard, mounting header. Double door, single operator. Specify length 49”to 98” maximum.

END CAPSHEADER END CAPS, 9530-334End cap with openings for wiring.

END DRESS PLATE, 9530-334-2Metal finish end cap.

ACCE

SSOR

IES3454

275 3018 344-1

3462

3572HL

3572DD

334 334-2



ARMSSTANDARD ARM ASSEMBLY, 9530-3077PLCMHanded arm.

STANDARD ARM, 9530-3077THanded arm. Track roller not included.

TRACKSTRACK 9530-3038Standard non-handed track.

TRACK END CAP 9530-73Black plastic end caps.

ROLLER, 9530-3034Quiet low friction roller assembly.

INSTALLATION ACCESSORIES

SPINDLE PLATE – 2 3/4”, 9530-11AHides bottom of motor gearbox. Completes header box. Cutoutallows for motor gearbox shaft. For 2 3/4" offset pivot or butthinge installations.

FILLER PLATE BLANK, 9530-12Completes length of header box. (Specify Length)

MOUNTING PLATE, 9530-18Optional mounting plate for standard hollow metal doorframes. Specify length 33” to 98” maximum.NOTE: The length of a universal 18 plate will need to beordered 3 1/2” longer than the supplied header.

ACCE

SSOR

IES

LCN 9530 SERIES 3077PLCM

3077T

3038 3034

11A

73

12

18



TABLE OF SIZES Indicates recommended range of door width for operator.

Note: For all Senior Swing SeriesSingle Door - Width per leaf 36” minimum, 48” maximum

LCN 9530 SERIES

DOOR WIDTH

36"914mm

48"1219mm

9531

MinimumDoor

Width

HOW-TO-ORDER9530 SERIES OPERATORS

1. SPECIFY HANDRHLH

2. SPECIFY FINISH.Standard Anodized Finish _____________Aluminum or Dark Bronze

Operator will be shipped with:-STANDARD MOTOR GEARBOX (SF)-STANDARD CONTROL BOX (SC)-36” HEADER (36HL)-STANDARD ARM (3077T)-2 3/4” PIVOT POINT-STANDARD TRACK w/TRACK ROLLER-MACHINE SCREW PACKUnless options listed below are selected.

OPERATOR OPTIONS

HEADERHL __ (Specify length 36” to 49”)DD__ (Specify length 49” to 98”)

MOUNTING PLATEPlate, ____ (Specify Length 30” to 98”)

SPECIAL TEMPLATEST-_________

ORDE

RINGI

NFOR

MATIO

N



LCN 9540 SERIES

STANDARD ANODIZED

CUSTOMANODIZED

CUSTOMPAIN

T

FINISH HANDING

HANDED

NON-HANDED

COVER

METAL

ARM FUNCTION

STANDARD (SIN

GLE)

REGULAR (D

OUBLE)

OFFSET PIVOT ARM

CENTER PIVOT ARM


)

MOUNTING

SURFACE MOUNT SIN

GLEDOOR

SURFACE MOUNT SIM

ULTANEOUS PAIR

SURFACE MOUNT IN

DEPENDENT PAIR

CONCEALED SIN

GLEDOOR

CONCEALED IN

DEPENDENT PAIR

CONCEALED SIM

ULTANEOUS PAIR




9540 series operator is shipped with motor gearbox, control box, regulararm, header, and mounting hardware. Actuators available separately,see page 121.

Single door, surface mounted.


Handed product.

36” header length is standard. Specify length 33” to 49” max.

Double door header available up to 98”, specify other length 49” to 98”max. Consult factory regarding this option.


SINGLE DOOR, SURFACE MOUNT (PUSH)OFFSET PIVOT/BUTT HINGE FEA

TURE

S




Reveal for push installations should not exceed 10” (254 mm) forREGULAR ARM and 20” (508 mm) for LONG ARM.






TOP JAMB SINGLE DOOR(OFFSET PIVOT/BUTT HINGE,CENTER PIVOT, PUSH) MOUNTI

Consult factory for all balancedoor installations.



LCN 9540 SERIES

Special TemplatesCustomized installation templates or products may be available to solve unusual applications. Contact LCN for assistance.

MOUN

TINGD

ETAILS

OUTGOING

PUSH ARM ASS'Y

17" From edge of door

OFFSET PIVOT

or BUTT

HINGES

2 3/4

"70 MM

SWING OPERATOR


RE

VE

AL

SWING OPERATOR

4 1/2

"114 MM

6 3/4

"171 MM

5 3/4

"146 MM

1"25 MM

DOOR

SWING DIRECTION

DOOR FRAME

EXTERIOR

1 7/16

" From top of door

SECONDARY LINK




MOUNTING BRACKETMOUNTING BRACKET – 2 3/4”, 9540-275Motor gearbox mounting bracket for 2 3/4" offset pivot or butt hingeinstallations. Front bracket.




HEADERSHeader, 9540-3572HLStandard, mounting header. Single door, single operator.Specify length 30”to 49” maximum.

Header, 9540-3572DDStandard, mounting header. Double door, single operator.Specify length 49”to 98” maximum.



ACCE

SSOR

IES3454

275 3018 344-1

3462

3572HL

3572DD

334 334-2



ARMSREGULAR ARM ASSEMBLY, 9540-3077Handed arm.

REGULAR LONG ARM ASSEMBLY, 9540-3077LHanded arm.

MAIN ARM, 9540 -77Handed arm attaches to motor gearbox.

LINKAGE ASSEMBLY – 15”, 9540-79Threaded rod attaches to door. Extends from main arm.

LINKAGE ASSEMBLY – 32”, 9540-79LRThreaded long rod attaches to door. Extends from main arm.Used for reveal 10” to 20”.

INSTALLATION ACCESSORIESSPINDLE PLATE – 2 3/4”, 9540-11AHides bottom of motor gearbox. Completes header box. Cutoutallows for motor gearbox shaft. For 2 3/4" offset pivot or butthinge installations.



ACCE

SSOR

IES

LCN 9540 SERIES 30773077L

77

7979LR

11A

12

18




Note: For all Senior Swing SeriesSingle Door - Width per leaf 36” minimum, 48” maximum

LCN 9540 SERIES

DOOR WIDTH

36"914mm

48"1219mm

9542

MinimumDoor

Width


1. SPECIFY HANDRHLH


Operator will be shipped with:-STANDARD MOTOR GEARBOX (SF)-STANDARD CONTROL BOX (SC)-36” HEADER (36HL)-REGULAR ARM (3077)-2 3/4” PIVOT POINT-WOOD and MACHINE SCREW PACKUnless options listed below are selected.

OPERATOR OPTIONSHEADER

HL __ (Specify length 36” to 49”)DD__ (Specify length 49” to 98”)

MOUNTING PLATEPlate, ____ (Specify Length 30” to 98”)

ARMLong Arm (3077L)

FINISHSPECIAL TEMPLATE

ST-_________

ORDE

RINGI

NFOR

MATIO

N



LCN 9550 SERIES

STANDARD ANODIZED

CUSTOMANODIZED

CUSTOMPAIN

T

FINISH HANDING

HANDED

NON-HANDED

COVER

METAL

ARM FUNCTION

STANDARD (SIN

GLE)

REGULAR (D

OUBLE)

OFFSET PIVOT ARM

CENTER PIVOT ARM


)

MOUNTING

SURFACE MOUNT SIN

GLEDOOR

SURFACE MOUNT SIM

ULTANEOUS PAIR

SURFACE MOUNT IN

DEPENDENT PAIR

CONCEALED SIN

GLEDOOR

CONCEALED IN

DEPENDENT PAIR

CONCEALED SIM

ULTANEOUS PAIR




9550 series operator is shipped with motor gearboxes, control box,arms, header, and mounting hardware. Actuators available separately,see pages 121.

Simultaneous pair, surface mounted.


Handed product.

Pull, Push or Double Egress applications available.

72” header length is standard. Specify other length 60” to 98”. Consultfactory regarding this option.


OPERATOR MOUNTSSIMULTANEOUS PAIR, SURFACE MOUNT

*PULL SIDEPUSH SIDE

DOUBLE EGRESS

FEATU

RES

*PULL SIDE mount shown





Reveal for pull installations should not exceed 4” (102 mm).

Reveal for double egress installations should not exceed 4” (102 mm).






TOP JAMB SIMULTANEOUSPAIR (OFFSET PIVOT/BUTTHINGE, CENTER PIVOT, PUSH)MOUNTING

TOP JAMB SIMULTANEOUSPAIR (OFFSET PIVOT/BUTTHINGE, CENTER PIVOT, PULL)MOUNTING


LCN 9550 SERIES

Special TemplatesCustomized installation templatesor products may be available tosolve unusual applications. Contact LCN for assistance.

MOUN

TINGD

ETAILS

OUTGOING

PUSH ARM ASS'Y


OFFSET PIVOT or BUTT HINGES

2 3/4

"70 MM

SWING OPERATOR

8'-0" DOOR OPENING (MAX.)

RE

VE

AL

OUTGOING

SWING OPERATOR

4 1/2

"114 MM

6 3/4

"171 MM

5 3/4

"146 MM

1"25 MM

DOOR

SWING DIRECTION

DOOR FRAME

EXTERIOR

1 7/16

" From top of door

SECONDARY LINK

PULL ARM ASS'Y

OFFSET PIVOT

or BUTT

HINGES

2 3/4

"70 MM

SWING OPERATOR


INCOMING

INCOMING

PULL CHANNEL

INTERIOR

17

3/8

"441 MM

1 3/4

"44 MM

11

1/2

"291 MM

SWING OPERATOR

4 1/2

"114 MM

6 3/4

"171 MM

5 3/4

"146 MM

1"25 MM

DOOR

SWING DIRECTION

PULL ARM ASS'Y

INTERIOR

PULL CHANNEL

1 15/16

"49 MM












TOP JAMB SIMULTANEOUSPAIR (RH DOUBLE EGRESS)MOUNTING

Consult factory for all balancedoor installations.



LCN 9550 SERIES


MOUN

TINGD

ETAILS

SWING OPERATOR

4 1/2

"114 MM

INTERIOR

PUSH ARM ASS'Y

PULL ARM ASS'Y

SWING OPERATOR

SWING OPERATOR


2 3/4

"70 MM


2 3/4

"70 MM

1 3/4

"44 MM


BUTT HINGES

11

1/2

"292 MM

17

3/8

"PULL CHANNEL

SWING OPERATOR

4 1/2

"114 MM

5 3/4

"146 MM

53/

4"

146

MM

6 3/4

"171 MM

SECONDARY LINK DOOR

FRAME

SWING DIRECTION

SWING DIRECTION

DOOR FRAME

DOOR

DOOR

1"25 MM

1"25 MM

23/

18"

FR

OM

BO

TTO

MO

FD

OO

RS

TOP

PULL ARM ASS'Y

PUSH ARM ASS'Y

115

/16"

FR

OM

TOP

OF

DO

OR

PULL CHANNEL

BUTT HINGES



LCN 9550 SERIES MOTOR GEARBOXMOTOR GEARBOX (STANDARD FORCE)– SENIOR SWING, 9550-3454

Driving mechanism for operator. Provides 15lbs opening force. Handed.

MOUNTING BRACKETSMOUNTING BRACKET – 2 3/4”, 9550-275Motor gearbox mounting bracket for 2 3/4" offset pivot or butt hinge installations. Front bracket.




COMPANION CABLE, 9550-982Cable that allows one control box to run two motor gear boxes.Companion cable. For use with Senior Swing.

HEADERSHEADER, 9550-3572HLStandard, mounting header. Pair door, two operators. Specify length 60”to 98” maximum.

END CAPSHEADER ENDCAPS, 9550-334End cap with openings for wiring.


ACCE

SSOR

IES 3454

275 3018 344-1

3462

982

3572HL

334 334-2



ARMSSTANDARD ARM ASSEMBLY, 9550-3077PLCMHanded arm.

REGULAR ARM ASSEMBLY, 9550-3077Handed arm.



MAIN ARM, 9550 -77Handed arm attaches to motor gearbox









ACCE

SSOR

IES

LCN 9550 SERIES 3077PLCM

30773077L

3077T 77

3038 3034

7979LR

73

11A 12

18




Note: For All Senior Swing SeriesSimultaneous Pair – Width per leaf 30” minimum to 48” maximum

LCN 9550 SERIES

DOOR WIDTH

60"1524mm

96"2438mm

9553

MinimumDoor

Width


1. SPECIFY HANDRHLH

2. SPECIFY FINISH.Standard Anodized Finish __________Aluminum or Dark Bronze

Operator will be shipped with:-STANDARD MOTOR GEARBOX (SF) (2 ea)-STANDARD CONTROL BOX (SC)-72” METAL COVER (72HL)-REGULAR ARM (2 ea)-2 3/4” PIVOT POINT-MACHINE SCREW PACK


HL__ (Specify length 60” to 98”)MOUNTING PLATE

Plate, ____ (Specify Length 30” to 98”) ARM

Standard Arm (2 ea)w/Standard Track (2 ea)Double Egress Includes Standard Arm w/Track (1 ea)& Regular Arm (1 ea)Long Arm (3077L)


ORDE

RINGI

NFOR

MATIO

N



LCN 9560 SERIES

STANDARD ANODIZED

CUSTOMANODIZED

CUSTOMPAIN

T

FINISH HANDING

HANDED

NON-HANDED

COVER

METAL

ARM FUNCTION

STANDARD (SIN

GLE)

REGULAR (D

OUBLE)

OFFSET PIVOT ARM

CENTER PIVOT ARM


)

MOUNTING

SURFACE MOUNT SIN

GLEDOOR

SURFACE MOUNT SIM

ULTANEOUS PAIR

SURFACE MOUNT IN

DEPENDENT PAIR

CONCEALED SIN

GLEDOOR

CONCEALED IN

DEPENDENT PAIR

CONCEALED SIM

ULTANEOUS PAIR




9560 series operator is shipped with motor gearboxes, control boxes,arms, header, and mounting hardware. Actuators available separately,see page121.

Independent pair, surface mounted.


Handed product.

Pull, Push or Double Egress applications available.

72” header length is standard. Specify other length 60” to 98”. Consultfactory regarding this option.


OPERATOR MOUNTSINDEPENDENT PAIR, SURFACE MOUNT

*PULL SIDEPUSH SIDE

DOUBLE EGRESS

FEATU

RES

*PULL SIDE mount shown












TOP JAMB INDEPENDENT PAIR(OFFSET PIVOT/BUTT HINGE,CENTER PIVOT, PUSH)MOUNTING

TOP JAMB INDEPENDENT PAIR(OFFSET PIVOT/BUTT HINGE,CENTER PIVOT, PULL)MOUNTING


LCN 9560 SERIES


MOUN

TINGD

ETAILS

OUTGOING

PUSH ARM ASS'Y


OFFSET PIVOT or BUTT HINGES

2 3/4

"70 MM

SWING OPERATOR


RE

VE

AL

OUTGOING

SWING OPERATOR

4 1/2

"114 MM

6 3/4

"171 MM

5 3/4

"146 MM

1"25 MM

DOOR

SWING DIRECTION

DOOR FRAME

EXTERIOR

1 7/16

" From top of door

SECONDARY LINK

PULL ARM ASS'Y

OFFSET PIVOT

or BUTT

HINGES

2 3/4

"70 MM

SWING OPERATOR


INCOMING

INCOMING

PULL CHANNEL

INTERIOR

17

3/8

"441 MM

1 3/4

"44 MM

11

1/2

"291 MM

SWING OPERATOR

4 1/2

"114 MM

6 3/4

"171 MM

5 3/4

"146 MM

1"25 MM

DOOR

SWING DIRECTION

PULL ARM ASS'Y

INTERIOR

PULL CHANNEL

1 15/16

"49 MM












TOP JAMB INDEPENDENT PAIR(RH DOUBLE EGRESS)MOUNTING

Consult factory for all balance doorinstallation.



LCN 9560 SERIES


MOUN

TINGD

ETAILS

SWING OPERATOR

4 1/2

"114 MM

INTERIOR

PUSH ARM ASS'Y

PULL ARM ASS'Y

SWING OPERATOR

SWING OPERATOR


2 3/4

"70 MM


2 3/4

"70 MM

1 3/4

"44 MM


BUTT HINGES

11

1/2

"292 MM

17

3/8

"PULL CHANNEL

SWING OPERATOR

4 1/2

"114 MM

5 3/4

"146 MM

53/

4"

146

MM

6 3/4

"171 MM

SECONDARY LINK DOOR

FRAME

SWING DIRECTION

SWING DIRECTION

DOOR FRAME

DOOR

DOOR

1"25 MM

1"25 MM

23/

18"

FR

OM

BO

TTO

MO

FD

OO

RS

TOP

PULL ARM ASS'Y

PUSH ARM ASS'Y

115

/16"

FR

OM

TOP

OF

DO

OR

PULL CHANNEL

BUTT HINGES




MOUNTING BRACKETSMOUNTING BRACKET – 2 3/4”, 9560-275Motor gearbox mounting bracket for 2 3/4" offset pivot or butthinge installations. Front bracket.



CONTROL BOXESCONTROL BOX – SENIOR SWING, 9560-3462Electronic controlling device for Senior Swing

HEADERSHEADER, 9560-3572HLStandard, mounting header. Pair door, two operators.Specify length 60”to 98” maximum.



ACCE

SSOR

IES 3454

275 3018 344-1

3462

3572HL

334 334-2



ACCE

SSOR

IES

LCN 9560 SERIES ARMSSTANDARD ARM ASSEMBLY, 9560-3077PLCMHanded arm.

REGULAR ARM ASSEMBLY, 9560-3077Handed arm.



MAIN ARM, 9560 -77Handed arm attaches to motor gearbox









3077PLCM

30773077L

3077T 77

3038 3034

7979LR

73

11A 12

18




Note: For all Senior Swing SeriesIndependent Pair – Width per leaf 30” minimum to 48” maximum

LCN 9560 SERIES

DOOR WIDTH

60"914mm

96"1219mm

9563

MinimumDoor

Width


1. SPECIFY HANDRHLH


Operator will be shipped with:-STANDARD MOTOR GEARBOX (SF) (2 ea)-STANDARD CONTROL BOX (SC) (2 ea)-72” METAL COVER (72HL)-REGULAR ARM (2 ea)-2 3/4” PIVOT POINT-MACHINE SCREW PACKUnless options listed below are selected.


HL__ (Specify length 60” to 98”)MOUNTING PLATE

Plate, ____ (Specify Length 30” to 98”) ARM

Standard Arm (2 ea)w/Standard Track (2 ea)Double Egress Includes Standard Arm w/Track (1 ea)& Regular Arm (1 ea)Long Arm (3077L)


ORDE

RINGI

NFOR

MATIO

N

*740100*740100

importantthese instructions are presented in step-by-step

sequence. it is very important that installation begins with “1. pre-installation Site and product Check” (page 3) and

continues as directed after each section.

warningalways disconnect main power to the operator prior to

replacing.Control box contains no serviceable parts inside.

Table of Contents

General Information ................................................................................................................................................................................... 1

Electrical Specifications ............................................................................................................................................................................. 2

1 Pre-Installation Site and Product Check ................................................................................................................................................. 2

2 Installation............................................................................................................................................................................................... 3

3 Wiring...................................................................................................................................................................................................... 3

4 Keypad Settings...................................................................................................................................................................................... 7

5 System Test ...........................................................................................................................................................................................11

6 Troubleshooting .................................................................................................................................................................................... 12

7 Release for Service .............................................................................................................................................................................. 13

General Information

The Senior Swing Control Box is for use with the Senior Swing Power Operator System. The system can operate a single door (2810, 9530, and 9540 Series), a simultaneous pair of doors (2850 and 9550 Series), or an independent pair of doors (2860 and 9560 Series).

anSi/BHma a156.19 ComplianceThe Senior S wing Power Operator System is a low energy product and must conform to the latest version of ANSI/BHMA A156.19 (American National Standard for Power Assist and Low Energy Power Operated Doors).

installation instructionsAll installation instructions are valuable references and should be given to the building owner or maintenance supervisor after installation is complete.

The Senior Swing Control Box installation instructions and the manufacturer’s instruction manual accompanying any sensor must be referenced to ensure proper installation, setup, and operation.

2800 Overhead Consealed Series9500 Surface Applied Series

Senior Swing Control Box

Installation Instructions

Electrical Specifications

AC input voltage .................................... 120 VAC

AC fuse .................................................. 120 VAC, 2.5 A time-delay fuse

Motor protection ..................................... Solid state failure detection and shutdown

Activate inputs ....................................... dry NO contacts (close contacts to open door)

Safety inputs .......................................... dry NO contacts (closed contacts indicate an obstruction)

Breakaway input .................................... dry NC contacts (open contacts indicate breakaway)

3-position switch input ........................... dry 3-position switch

Power Boost disable input ..................... dry NO contacts (close contacts to disable Power Boost)

Lock output ............................................ Form C dry relay contacts rated 8 A, 30 VDC maximum

Accessory power output ........................ 24 VAC, 1.5 A (protected by resettable thermal fuse)

Logic power output ................................ 5 V, 50 mA (protected by resettable thermal fuse)

1 Pre-Installation Site and Product Check

importantFactory authorized Door Leaf Size and weight

Type Width per Leaf Maximum Weight per LeafSingle Door 36” to 48” 200 lb.

Simultaneous Pair 30” to 48” 200 lb.

1a All required installation steps listed before “8. Control Box Installation” in the Senior Swing installation instructions should be completed before installing the Senior Swing control box.

1b Check that the control box model (indicated on control box label; Figure 1-1) is correct for the application.

1c Check that the available AC voltage matches the control box voltage requirement (120 VAC).

1d Check that all accessories required for the application are on hand.

Figure 1-1

Label indicates model

CAUTION: 120 VAC2.5 A TIME-DELAY FUSE

WARNING: FOR CONTINUEDPROTECTION AGAINST FIRE,REPLACE ONLY WITH SAMETYPE AND RATING OF FUSE.

COMPANIONMOTOR

COMPANION MASTER

CLOSESPEED

SLOW

FAST

CLOSESPEED

SLOW

FAST

: OPENING SPEED: BACKCHECK SPEED: BACKCHECK POS.: HOLD-OPEN DELAY: LATCH POSITION: AUTO-REV. CLOSING: ELECTRIC LOCK: POWER BOOST: PUSH ‘N’ GO: ALTERNATE ACTION: SAFETY SLOW/STOP: SPECIAL: STATUS ANNOUNCEMENT

SETTING VALUE

DEFAULT

POWERON

UP

DOWN

UP

DOWN

WARNING: ALL SPEEDSETTINGS (OPENING,CLOSING, AND LATCHING)AND HOLD-OPEN TIME-DELAY MUST BE FIELDADJUSTED TO MEETLATEST APPLICABLE ANSI/BHMA STANDARDS.

DMSS #2

APPR

OACH

P5

DMSS #2

SAFE

TYP4

ELEC

TRIC

LOCK

P10

RETR

OFIT

P8

BODY

GUAR

D

P1

ACTIV

ATE

P6

ACTIV

ATE

P7

DMSS #1

APPR

OACH

P3

DMSS #1

SAFE

TYP2SENIOR SWING

710164

elbaecivreS oN

edi snI str aP

2 Installation

To install the Senior Swing Control Box, follow the Senior Swing installation instructions beginning with “8. Control Box Installation” on page 12 of those instructions.

Cautionimproper installation or set up may result in personal

injury or property damage. Follow instructions carefully. For answers to questions, call 1-877-671-7011

3 Wiring• Review the separate wiring diagrams in the accessory instructions so that all wiring can be completed.• See Figure 3-1 for system configuration terminology.• See Figure 3-2, Figure 3-3, and Figure 3-4 for names and locations of control box connectors.• See Figure 3-5 for control box plug and jack descriptions, wiring, and mating cables.• See Figure 3-6 for electric strike locking device sample wiring.• See Figure 3-7 for EL (electric latch retraction) locking device sample wiring.

Cautionwhen joining or separating a plug and receptacle, do not push or pull on wires. this may cause a wire to be pulled loose from a terminal, which may result in a malfunction.

Figure 3-1

Connect operator for second door to controlbox Companion Motor Power receptacle(P5 on control box power board)

Connect masteroperator to controlbox Master MotorPower cable

Connect single dooroperator to MasterMotor Power cablefrom control box

Safetyside

ApproachsideApproach

side

Safetyside

Figure 3-2. Control box power board connectors.

Figure 3-3. Control box logic board connectors.

Figure 3-4. Closeup of control box logic board connectors.

P5

P3 P2 P1 P6 P7

P4 P10P8

DMSS (companion; safety side)

Activate

Activate

DMSS (master; safety side)

DMSS (master; approach side)

DMSS (companion; approach side)

LOGIC BOARD

Companion motor power

(P5)

POWERBOARD

LOGIC BOARD

AC fuse, 120 VAC2.5 A time-delay

Master motorpower

ACpower

Bodyguard (safety side)

Breakaway

3-positionswitch

POWER BOARD

LOGIC BOARD

See Figure 3-4 forcloseup of control

box logic boardconnectors

Locking Interface andPower Boost disable input

RetrofitAccessories

THenderson

Polygon

Figure 3-5

Black, 24 VACRed, 24 VACWhite, ActivateGreen, Ground

Black, 24 VACRed, 24 VACWhite, SlowdownGreen, Ground

Black, 24 VACRed, 24 VACWhite, ActivateGreen, Ground

Black, 24 VACWhite, 24 VACYellow, ActivateGray, Ground

Black, 24 VACWhite, 24 VACYellow, ActivateGray, Ground

Blue, Carpet SafetyGray, GroundYellow, ActivateViolet, Slowdown

OrangeBlack

RedGreenBlack

BodyguardJST-type

connector

To DMSS(master;safety side)

To DMSS(master;approach side)

To DMSS(companion;safety side)

To DMSS(companion;approach side)

To existing cable710057 (old partNo. 81276)

To 3-positionswitch (if used)

To motor cable ofcompanion operator(use only for seconddoor of simultaneouspair of doors)

To motor cable ofmaster operator(always use forsingle door)

Bodyguard cableto Bodyguard

sensorCable761468

Cable761464

Cable761464

Cable761469

Cable761465

To locking device(see page 7 forsample wiring)

Cable761466

Cable761463

Retrofitonly

If used

If used

If used

If used

If used

If used

If used

If used

If used

Activate: Initiates a door opening cycle

Bodyguard (master; safety side): Preventsdoor from opening; holds open door in openposition (uses door state data from control boxto ignore door movement while opening/closing)

DMSS (master; safety side): Prevents door fromopening, and slows an opening door

Activate: Initiates a door opening cycle(operates identically to P6 and is provided asa convenience if 2 activations are used)

DMSS (master; approach side): Initiates a dooropening cycle if activated while door is closing

AC Input: 120 VAC

Companion Motor Power: Companion motorpower (use only for second door of simultaneouspair of doors)

Master Motor Power: Master motorpower (use for single door)

3-Position Switch: OFF, AUTO, HOLD

Locking Interface: Power output and relaycontacts for locking devices; Power Boostdisable input

Breakaway: Disables operator inputs whenBreakaway switch is active

DMSS (companion; safety side): Prevents doorfrom opening, and slows an opening door

DMSS (companion; approach side): Initiates adoor opening cycle if activated while door is closing

Retrofit Accessories: Accesses older modelActivate, Slow/Stop, and Carpet Safety inputs

P1

P2

P3

P4

P5

P6

P7

P8

P10

P5

LOG

IC B

OA

RD

POW

ER B

OA

RD

To normally closedBreakaway switchor jumper 81269

White, 24 VACWhite, 24 VAC

Black, Hot ACWhite, Neutral ACGreen, Earth Ground To 120 VAC

Black, 24 VACRed, 24 VACWhite, SlowdownGreen, Ground

DMSSharness761467

Safety

Approach

Safety

Approach

Safe

tyytefaS

hcaorppAAp

proa

ch

on-boardconnector

on-boardconnector

on-boardconnector

on-boardconnector

on-boardconnector

on-boardconnector

on-boardconnector

on-boardconnector

on-boardconnector

on-boardconnector

perm

anen

tco

nnec

tions

perm

anen

tco

nnec

tions

perm

anen

tco

nnec

tions

perm

anen

tco

nnec

tions

DMSSharness761467

Activate cableTo normally open Activate contacts

Activate cableTo normally open Activate contacts

Used only for powered activation device

Used only for powered activation device

Blue, Power Boost disableBlack, GroundViolet, Relay NOGray, Relay COMBrown, Relay NCGreen, 5 V

To normally openPower Boostdisable contacts

Ground

THenderson

Polygon

THenderson

Line

THenderson

Callout

connect the white wire on the key switch to the red wire on the control board to opener hold open

THenderson

Callout

connect the red wire on the key switch to the black wire on opener will make it close

THenderson

Polygon

THenderson

Callout

THenderson

Callout

FA relay will tie into Hold Open activation, when alarm activates relay it will interupt power to hold open and door will close on its own

THenderson

Line

L notE: always wire the locking device to the no (normally open) contact of the control box locking interface and use the keypad to set the EL (electric lock) setting to either Sa (fail safe) or SE (fail secure).

The keypad EL (electric lock) setting is SA (fail safe). When the operator is on, the strike is locked whenthe door is closed and unlocked when the door is opening. When the 3-position switch is set to OFF, thestrike is unlocked.

The keypad EL (electric lock) setting is SE (fail secure). The control box locking relay signals the PS914x 900-2RS. When the operator is on, the EL device is locked when the door is closed and unlocked when thedoor is opening. When the 3-position switch is set to OFF, the EL device is locked.

Figure 3-7. Sample Wiring for a Fail Secure EL (Electric Latch Retraction) Locking Device

Figure 3-6. Sample Wiring for a Fail Safe Electric Strike Locking Device

Cable 761465 to Senior Swing control box lockinginterface receptacle (P10)

Fail safeelectricstrike

Rectifier(for DCstrikes)

Senior Swingcontrol box

EL device

Gray (COM)

Violet (NO)

Cable 761465 toSenior Swing control box locking

interface receptacle (P10)

Senior Swing control box

Control box lock supply rating: 24 VAC, 1.5 A

WhiteWhite

Gray (COM)Violet (NO)

White

White

Black

Red

Cut connector off rectifier, thenconnect using wire nuts

When using an EL device such as EL33A, EL99, etc:Use 12 AWG stranded wire for outputs 01 and 02between PS914 and EL device (200’ run maximum).

SC I1 01 I2 02 GND

Von DuprinPS914 x 900-2RS

4 Keypad Settings

Settings (except for close speed) for the Senior Swing Power Operator System are changed using keypad pushbuttons and an alphanumeric display on the control box (Figure 4-1 and Figure 4-2). Close speed is changed using dials on the control box (Figure 4-1).

See page 9 and page 10 for directions for changing the values of settings.

Cautionadjust the operator for the slowest operation practical in accordance with the latest revisions of americans with

Disabilities act, anSi/BHma a156.19 (american national Standard for power assist and Low Energy power operated Doors), and

local codes.

Figure 4-1. Control Box Panel with Keypad

Figure 4-2. Closeup of Control Box Keypad

SETTING VALUE

NWODNWOD

PUPU

DEFAULT

POWERON

Setting display

Reset to defaultvalues pushbutton

Value selectionpushbuttons

Setting selectionpushbuttons


Value display

KeypadClose speed dials

CAUTION: 120 VAC2.5 A TIME-DELAY FUSE

WARNING: FOR CONTINUEDPROTECTION AGAINST FIRE,REPLACE ONLY WITH SAMETYPE AND RATING OF FUSE.

COMPANIONMOTOR

COMPANION MASTER

CLOSESPEED

SLOW

FAST

CLOSESPEED

SLOW

FAST


SETTING VALUE

DEFAULT

POWERON

UP

DOWN

UP

DOWN

WARNING: ALL SPEEDSETTINGS (OPENING,CLOSING, AND LATCHING)AND HOLD-OPEN TIME-DELAY MUST BE FIELDADJUSTED TO MEETLATEST APPLICABLE ANSI/BHMA STANDARDS.

DMSS #2

APPR

OACH

P5

DMSS #2

SAFE

TYP4

ELEC

TRIC

LOCK

P10

RETR

OFIT

P8

BODY

GUAR

D

P1

ACTIV

ATE

P6

ACTIV

ATE

P7

DMSS #1

APPR

OACH

P3

DMSS #1

SAFE

TYP2SENIOR SWING

710164

elbaecivreS oN

edi snI str aP

warningKEEp HanDS, CLotHing, wirES, tooLS, LaDDErS,

EtC. awaY From tHE Door wHEn tHE opErator iS initiaLLY turnED on.

See Figure 4-3 for definitions of the positions of the door throughout the opening and closing cycle.

See Table 4-1 for explanations of the keypad settings.

to change setting values:1. Set the 3-position switch, if used, to OFF.

2. Apply AC power. The POWER light will illuminate and the display will remain blank.

3. Press any two pushbuttons at the same time for 1 second to turn on the keypad. The display will illuminate.

4. Press the UP or DOWN setting selection pushbutton to select the desired setting. The setting is shown in the SETTING display, and the current value for that setting is shown in the VALUE display.

5. Press the UP or DOWN value selection pushbutton to select the desired value for the displayed setting. The value for the setting is indicated in the VALUE display.

6. The keypad will automatically turn off after 5 minutes of inactivity.

to reset all values to default (default values are listed in table 4-1 under “Selectable Values”):1. Set the 3-position switch, if used, to OFF.

2. Apply AC power. The POWER light will illuminate, and the display will remain blank.

3. Press any two pushbuttons at the same time for 1 second to turn on the keypad. The display will illuminate.

4. Press the DEFAULT pushbutton for 4 seconds.

5. The values are set to default, and the display will indicate the opening speed setting and value.

6. The keypad will automatically turn off after 5 minutes of inactivity.

Back check speedBack check position

Openingspeed

Closingspeed

Latch positionDeceleration to fully

closed position

Figure 4-3. Door Position Definitions

Safety side Door mounted Safety Sensor (DmSS) disable featurepurpose:Deactivate the Door Mounted Safety Sensor (DMSS) on safety side of door to eliminate nuisance detection of a wall or guard rail.

1. Install control box, all door hardware and safety devices per their instructions.

2. Setup DMSS sensors in accordance with ANSI standard 156.10.

3. Use keypad to set SAFETY SLOW/STOP (SS) value to STOP (SP).

4. Use keypad to set SLOWDOWN DISABLE (SD) value to 85.

5. Activate door opening cycle. If door does not open fully, use keypad to reduce SD value from 85 in 5 degree increments.

6. Repeat Step 5 until door opens fully.

7. Perform a complete system test as described in the section 5.

Frame

Wall

rosn

eS ev

itcA(85 degrees or less)

Safe

ty s

ide

DM

SS S

enso

rD

oor

DM

SS S

enso

r

table 4-1. Control Box Settings and Selectable Values

Setting Setting Display Selectable Values Values as Displayed

Description

Opening Speed 01 = slow 02 = medium

03 = fast (default = 01)

Controls opening speed of any normal weight and size door

Back Check Speed 01 = 1 door 02 = 2 doors (default = 01)

Controls speed of door near full open position to prevent door slamming open

Back Check Position 45-80 degrees (default = 70)

Approximate angle at which door begins to decelerate near the full open position

Hold Open Delay 01-32 seconds (default = 05)

Amount of time (in seconds) door remains fully open following an activate signal

Latch Position 00-23 degrees (default = 13)

Approximate angle at which door begins to decelerate near the full closed position

Auto Reverse Closing off, on (default = off)

When on, door will re-open upon hitting an obstruction

Electric Lock

off SA = fail safe

SE = fail secure (default = off)

To turn on, set to SA (fail safe) or SE (fail secure) to match locking device connected to control box locking interface receptacle (P10); when on, causes a 1 second delay between activate signal and door opening to allow time for most electric locks to disengage before operator opens door

Power Boost

off 5 seconds continuous

(default = off)

When on, increases closing force of door from 9 lbs to 18 lbs to close door against high winds or stack pressure; turns on for 5 seconds or continuously after door reaches latch position during closing cycle; disabled by Power Boost disable input

Push ‘N’ Go

off, on, fd (default = off)

When set to On or Fd, pushing door open 5 degrees causes operator to open door remainder of way and hold open. Hold open time is same as hd setting when set to On. Hold open time is 1 second when set to Fd.

Alternate Activate off, on (default = off)

When on, door stays open until a second activate signal is received.

Safety Slow/Stop

slow, stop (default = slow)

Determines response to a DMSS on the safety side of the door; if SL (slow), door goes to back check speed; if SP (stop), door stops for 5 seconds, then continues opening at back check speed

Special off 30-85

(default = off)

Deactivate the Door Mounted Safety Sensor (DMSS) on safety side of door to eliminate nuisance detection of a wall or guard rail.

Status AnnouncementReserved Reserved

Reserved

5 System Test

warningKEEp HanDS, CLotHing, wirES, tooLS, LaDDErS,

EtC. awaY From tHE Door wHEn tHE opErator iS initiaLLY turnED on.

If control box does not operate as expected during system test, see section 6 for troubleshooting tips.

5a With the door closed, set the 3-position switch, if used, to AUTO and turn on all AC power. For applications using companion door, try to get both doors to open same amount of degrees before hitting hard stop (either internal gearbox stop or rubber bumper on wall).

5b Activate the operator using an activation device. The operator should perform one sizing cycle.Sizing cycle: Occurs when the door is activated for the first time after power is turned on. During the sizing cycle, the door opens and closes once.

if the door sizes properly, go to step No. 5.3.

if the door does not open at all during the sizing cycle:• Check that the 3-position switch, if used, is not set to OFF.• Check door for binds and proper mechanical installation.• Verify that all safety sensors are inactive.• If an electromechanical lock is used, check that the lock disengages before the operator opens the door.• Verify that the Breakaway switch, if used, is connected to NC contacts. If a Breakaway switch is not used, check that the Breakaway

cable coming from the control box logic board is jumpered (jumper part No. 761492-00).• Check fuse, wiring, and connections.• Adjust the operator as follows and check door operation:

Opening speed: ..........................01 Back check speed: ......................01 for one door, 02 for two doors Hold open delay: .........................05 Back check position: ...................75 Latch position: .............................10 Close speed: ...............................medium Electric lock: ................................SA (fail safe) or SE (fail secure) to match lock

if the door does not open fully during the sizing cycle, check door for binds, obstructions, or items that could activate safety sensors.

5c After the sizing cycle is complete and the door is closed, apply a maintained activation signal and check that the door remains open while the activation signal is applied. Then release the activate signal and verify door closes after the open time delay expires.

5d To check the function of the door safety device:1. Activate the door and then activate the approach side safety device while the door is open. The door should not close while the

safety device is activated. Next, deactivate the safety device. The door should close after the hold open time delay expires.

2. With the door closed, activate the safety side safety device, then activate the door. The door should not open while the safety device is activated. Next, deactivate the safety device. The door should open when activated.

5e Set the 3-position switch, if used, to HOLD. Verify that the door opens and stays open.

5f Set the 3-position switch, if used, to OFF. Verify that the door closes. Verify that an activate signal does not open the door.

5g If a Breakaway switch is connected, set the 3-position switch, if used, to AUTO, then break open the door. Verify that an activate signal does not cause the door to move. Re-latch the door after testing.

5h Do not release the system for service until it is operating properly.

6 Troubleshooting6a Identify all switch and sensor inputs that are currently active:1. Remove breakaway jumper to enter diagnostic mode. L note: when in diagnostic mode, controller will not open door.

2. Keypad display shows each active input signal for 1 second. See table below:

(Key switch) set to Auto OR is not present ......................... SA80 (Key switch) set to OFF ...................................................... SA81 (Key switch) set to HOLD ................................................... SA82 (Activate) input is ON .......................................................... SA83 (DMSS approach) activate input is ON ............................... SA84 (DMSS safety) slowdown input is ON ................................. SA85 (Carpet Safety) input is ON ................................................ SA86 (Bodyguard) input is ON ..................................................... SA87 (Power Boost Disable) input is ON ..................................... SA88

For example, if key switch is set to Auto, Activate button is pressed, and DMSS sees something on the safety side, then display will repeat the sequence SA80, SA83, SA85 continuously until breakaway jumper is replaced.

3. After completing diagnostics, reinstall breakaway jumper for normal operation.

© Allegion 2014Printed in U.S.A.

740100 Rev. 02/14-h

6b If control box does not function and the error message Er## flashes on the control box Setting and Value displays, turn AC power off and on to reset the control box. The following are common errors and suggested fixes:ER 06: Master motor problem - verify master motor cable is connected to motor. ER 14: Companion door added to a setup that was already sized - turn AC power off, then on and resize with both doors connected.

If problem cannot be corrected by using suggested fixes, contact 1-877-671-7011.

7 Release for Service7a Remove all tools, installation equipment, and debris from the vicinity of the door.

7b Install all safety, traffic control, and instruction decals on the door as required by the latest revision of ANSI/BHMA A156.19. This is very important! Failure to do this leaves the installer LIABLE for any accident that might occur. This must be done!

7c Verbally instruct the owner or person in charge of the proper operation of the door.

7d Instruct the owner or person in charge to routinely inspect the door for the following:• Visible damage• Developing problems• Minor preventive maintenance

7e Instruct the owner or person in charge who and where to call for service when required.

importantMake sure to install all safety, traffic control, and

instruction decals on the door as required.

Customer Service1-877-671-7011 www.allegion.com/us

of 18 740132-00(0)

3. SURFACE HEADER INSTALLATION

Figure 3-1

3.1. For a header with two operators (for a simultaneously operated pair of doors), designateone end of the header as the companion operator end. (It does not matter which end.)

3.2. Refer to Figure 3-1 and step 3.3 and prepare wire access holes appropriate for theapplication in the header using template 91194-684. Be sure to position edge “A” oftemplate 91194-684 as shown in Figure 3-1.

20”

20”

Edge “A”

Edge “A”Double operatorholes on top

COMPANION END

COMPANION END

20”

20”

Edge “A”

Edge “A”

Back of header

Back of header

Double operatorholes on back

COMPANION END

COMPANION END

Single operator, holes on backSingle operator, holes on top

Edge “A”

3.3. Install horizontal mounting brackets on the header per the instructions supplied with thebrackets (Figure 3-2). Make sure the horizontal mounting brackets are oriented so the wireaccess holes in the header (see step 3.2) face up or face the door and, for single operatorheaders, the operator brackets inside the header are near the hinge side of the opening.

Edge “A”

Edge “A”Back of headerBack of header

Figure 3-2

Operator brackets(inside header)Horizontal

mountingbracket

Horizontalmountingbracket

Operator brackets(inside header)

THenderson

Callout

where are these holes located in relationship to the inside edge of opening and from each other?

THenderson

Line

thenderson

Polygon

thenderson

Callout

Conduit will always come in from strike side of opening

thenderson

Callout

on pairs come 20" from hinge side (either side)

thenderson

Polygon

thenderson

Line

lcn automatic operators · lcn automatic operators senior swing 9530 senior swing 9540 senior swing...

Documents