lamina catalog 2016 en 06feb2017 - dallagottcdallagottc.com/.../2017/02/catalogo-lamina-2016.pdf ·...
TRANSCRIPT
MADE IN SWITZERLAND
PRODUCT LINE 2016
Index
Turning 17
Thread Milling 351
User Guide 3
Drilling 337
Thread Turning 193
Alu-Milling 331
Alu-Turning 161
Solid End Mills 355
Contact Information 383
Parting 177
Materials Reference List 377
Milling 203
© Lamina Technologies 2016
MADE IN SWITZERLAND
3
USER GUIDE
User Guide
4
USER GUIDE
For new users of Lamina Technologies Multi-MatTM (multi-material) inserts and to get more productivity and longer tool life, we have prepare a short machining guide to insure your satisfaction with our products.
The machining conditions included after each insert are our guidelines for optimal machining. However, our inserts can work in wide range of cutting conditions to meet special machining needs.
Check the condition of the tool holder (insert seat, shim, lever, screw) and check if the insert is well seated and clamped.
If there are interrupted cut or passes with short lengths of cut, dry operation is recommended to avoid thermal shocks. For heavy interrupted cut feed rate should be reduced.
Coolant
Check the stability of the machine. The tool overhang should be as short as possible.
Cutting speed has the greatest influence on tool life. For high productivity and long tool life, first increase d.o.c. and feed rate.
Vc
fn
d.o.c
Tool life
Cutting parameters
+
+-
-
Respect maximum chip section area for each insert. Amax = feed x d.o.c.
Feed x d.o.c.=
Amax
For higher productivity and better chip control in roughing, work close to the recommended Amax value.
Section max
[mm2]Depth of cut
[mm]
Feed
[mm/t]f maxf min
Machining Optimization
Turning
5
USER GUIDE
Climb Milling:Usually this is the recommended direction. Tool life up to 40% longer than conventional.
Vf
Conventional Milling:Recommended only for:• Old machines with backlash in the table transmission• Flame cut, forged and cast workpieces• Thin workpieces (in order to reduce vibration)Vf
Fv
К = 90° Approach angleHigh radial forces / Low axial forces.Recommended:• When 90° wall is needed• For unstable conditions• For slender workpieces
h = fz
fz
For face milling the width of cut (ae) should be about 70% of the cutter diameter, in order to achieve better chip formation and longer tool life. For limited engagement conditions, it is necessary to increase feed per tooth.
0.7 x DD
К = 45° Approach angle identical radial and axial forces. High productivity fz = 1.41 x hRecommended:• When overhang is long (lower vibration tendency)• For face milling (1st choice)
h = 0.71 x fzfz
45°
Round Inserts:Roughing and general purposes. Strongest cutting edge.
Milling
Check the condition of the tool holder (insert seat, shim, lever, screw) and check if the insert is well seated and clamped.
Check the stability of the machine. The tool overhang should be as short as possible.
Machining Optimization
6
USER GUIDE
Description
The workpiece material is welded to the cutting edge. Normally caused by low temperatures.
Built-up Edge (Adhesive Wear) Solution
• Increase cutting speed • Increase feed• Use more positive geometry
Notch wear (Adhesive/Mechanic Wear) Description
Result of adhesive or mechanical action. Chipping or localized wear at the depth of cut line.
Solution
• Use more positive geometry• Reduce feed• Vary depth of cut
Crater (Chemical Wear) Description
Happens on the rake surface. Normally the result of a combination of a diffusion and abrasion wear mechanism.
Solution
• Decrease cutting speed• Check coolant direction• Use more positive geometry
Flank Wear (Abrasive Wear) Description
Abrasive wear mechanism that happens on the cutting edge’s flank. Not common in Lamina inserts.
Solution
• Decrease cutting speed• Check coolant direction.
Plastic Deformation (Thermal Wear) Description
Caused by cutting forces and too high temperature. Not common in Lamina inserts.
Solution
• Decrease cutting speed• Decrease feed rate
Thermal Cracks (Thermal Wear) Description
Small cracks normally at 90° to the cutting edge caused by temperature variation
Solution
• Stabilize the temperature• Shut off the coolant
Breakage (Mechanic Wear) Description
Most breakages happen because the wear development is not seen in time.
Solution
• Check the tool holder• Check the tool overhang• Check the Amax• Decrease feed and Vc• Apply more robust insert• Check the run-out
Machining Optimization
7
USER GUIDE
Material Groups
1
2
3
6
4,6
5,7
8
10
10
11
11
14
14
14
14
12
13
15
15
16
17,19
17,19
18,20
31,32 Incoloy 800
33 Inconel 700
34 Stellite 21
36 TiAl6V4
37 T40
38
38
38
Chilled Cast Iron 40 Ni-Hard 2
White Cast Iron 41 G-X300CrMo15
Al (>8%Si) 12 25 AlSi12
Si < 4 %
4% < Si < 8 %
Cooper Alloys 14 26,27,28 CuZn30
29 Fiber Plastics
30 Hard Rubber
- Graphite
Non-ferrous and soft materials (less than 130HB of hardness). Most common: Aluminum
Composition: Fe-C alloy with 2.1 to 5% of carbon. It can be alloyed with Si, P, Mn and Ni. Characteristics: Grey cast iron tends to be brittle, and malleable cast irons usually have a more ductile but less homogeneous microstructure. Reinforced cutting edges will perform best. High productivity can be achieved by using high feeds.
Caution
Notch wearCrater
Built-up edge
Non-alloyed SteelComposition: Fe-C alloy (usually 0.1 to 0.6% carbon).Characteristics: Good machinability and high cutting speeds can be applied. When it has less than 0.25% carbon, it can be very sticky, requiring positive rake and small land inserts.Alloyed SteelComposition: Fe-C alloy (maximum 2.1% carbon) with additives like Cr, Mo, V, Ni, Mn, Co, W, etc. Characteristics: The variation in the amount of alloying elements and different heat treatments control features such as mechanical resistance and machinability. It's important to follow the cutting speeds recommended according to the hardness of the steel, as it influences temperature as well as chemical and adhesive wears. High alloyed Steel have more than 5% alloying elements.
Composition: Alloyed steel, more than 11% chrome (Cr).Characteristics: Stainless steels do not stain, corrode, or rust as easily as ordinary steel. Usually they are difficult to machine because of its narrow range of cutting speeds. If the cutting speed is too low, the material sticks in the cutting edge, if it’s too high, the high quantity of additives produces abrasive wears in the cutting edge.
This group includes hardened and tempered steel up to 55 HRc, chilled and white cast iron up to 55 HRc. Machining success depends largely on clamping system rigidity, as cutting forces and power consumption are high. Finishing represents the majority of the operations for this material group.
Crater
Composition: Iron (Fe) based, Nickel (Ni) based or Cobalt (Co) based alloys and Titanium alloys.Characteristics: High temperature alloys and titanium provide excellent mechanical strength resistance, as well as corrosion and oxidation resistance. Relatively low cutting speed is recommended due to their poor thermal conductivity.
Built-up edge Crater
Al (<8%Si)
NFHi
gh T
e mp.
All o
y s
Fe, Ni &Co based
9
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Composition: Al alloys can be alloyed with Cu, Zn, Mg, Mn and Si.Characteristics: Aluminium is widely used due to its low density and relatively good strength to weight ratio. When machining, it tends to have long chips and built-up edge. A highly positive cutting edge together with low friction coating control the chips and reduce built up edge.
St
eel
Material Group Gr. N°VDI
GroupMaterial
Examples*Description
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
304, 316, X5CrNi18-9
Duplex 5X2CrNiN23-4,
S31500
4
Ferritic & Martensitic
6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7
Malleable & Nodular
8
Stai
nles
s St
eel
Austenitic
GG20, GG40, EN-GJL-250, No30B
15Non-Metallic
Ti based 10
GGG40, GGG70, 50005
Steel
11
21, 22 23, 24
13
Built-up edge Crater
Crater
Flank wear Crater
Mechanical cracks
Built-up edgeNotch wear
Notch wearCrater
Crater
8
USER GUIDE
Magia Premium Grades
Magia for Turning
Now with three Magia grades for turning, Lam-ina Technologies provides further options for a greater range of application, improved efficien-cy and longer tool life.
LT 1000Recommended for general usage
Multi-MatTM LT 1000 is the most versatile grade of the Magia turning line with excellent combina-tion of hardness and toughness.
It is the first choice for customers with short pro-duction runs, different machining applications and different types of workpiece materials.
LT 1005Recommended for stable conditions, moderate to high speeds, for P, K, H material groups
Increased hardness and wear resistance at high temperatures makes this grade well suited for stable conditions and higher cutting speeds.
Highly resistant to plastic deformation thus maintains high dimensional tolerance.
LT 1025Recommended for unstable conditions, moderate to low speeds, for P, M, K material groups
Increased toughness makes this grade excel-lent for unstable conditions, such as interrupted cut.
The low chemical affinity between top ceramic layer and workpiece material ensures low fric-tion and increased resistance to built-up edge development even at low cutting speeds in fac-ing applications.
Magia for Milling
Lamina Technologies’ new generation, premi-um Multi-MatTM milling grade, LT 3000, provides higher performance, more productivity, excel-lent mechanical and improved thermal shock resistance for even longer tool life.
LT 3000
Denser micro structured coating. High quality substrate.
Magia LT 3000 inserts are made from Lamina Technologies’ advanced substrate, now with a denser micro structured, smoother coating, which allows for even lower wear rates.
Progressive and predictable wear.
The new silver top layer provides more contrast on worn edges making it easy to identify which edge has been used and the level of wear de-velopment.
More flexibility. Extended application range.
With a more tolerant coating, LT 3000 permits added flexibility and a wider application range as it can be applied at higher and lower cutting speeds than LT 30.
Lamina Technologies has augmented its Magia range of premium grades with the introduction of two new optimized, multi-layer CVD grades for turning and an advanced PVD grade for milling.
9
USER GUIDE
Material Group * = 1st choice grade
High SpeedsStable Conditions
Interrupted Cut Unstable Conditions
Low Speeds Facing to Center
** LT1005 LT1005 harder
LT1000 LT1000 LT1000
LT1025 *LT1025 *LT1025 tougher
LT1005 harder
* LT1000 LT1000 LT1000
LT1025 * LT1025 * LT1025 tougher
* LT1005 LT1005 harder
LT1000 LT1000 *LT1000* LT1025 LT1025 tougher
harder
* LT1000 * LT1000 * LT1000tougher
LT1005 LT1005 LT1005 harder
* LT1000 * LT1000 * LT1000tougher
harder
* LT1000 * LT1000 * LT1000tougher
Wear Resistance X
Toughness
P
M
K
S
H
N (>8%Si)
Toughness
Hardness
LT 1000
LT 1005
LT 1025
Grade Chart
10
USER GUIDE
Negative Turning Chipbreakers
Finishing
Steels _NMP NN NX _NMG NN NM
Stainless Steels _NMP NN NX _NMG NN
_NMP NN NX _NMG NN
Cast Iron NM (Gr. 8) _NMA (Gr. 7)
High Temp Alloys
_NMG NN NM _NMAHardened Material
_NMP NN NX _NMG NNAlu (>8%Si)
Light Cut, Stable conditionsRoughing,
Unstable Conditions
Negative Turning Chipbreakers: Overview
11
USER GUIDE
Continuous cut Interrupted cut Continuous cut Interrupted cut
NX * NX _NMP NN NX sharper
_NMG NN NN NX * _NMG NN *
NM NM * _ NMG NN NM stronger
_NMP NN _NMP NN * sharper
NX * NX * NX NX *_NMG NN _NMG NN _NMG NN _NMG NN stronger
_NMG NN _NMG NN _NMG NN *(Mat Group 8) _NMG NN sharper
NM * (Mat Group 8) NM * (Mat Group 8) NM NM * (Mat Group 8)
_NMA * (Mat Group 7) _NMA * (Mat Group 7) _NMA * (Mat Group 7) _NMA * (Mat Group 7) stronger
_NMP NN _NMP NN * sharper
NX * NX * NX NX * _NMG NN _NMG NN _NMG NN _NMG NN stronger
_NMG NN _NMG NN _NMG NN * _NMG NN sharper
NM * NM * NM NM *_NMA _NMA stronger
_NMP NN _NMP NN sharper
NX * NX NX * NX
_NMG NN _NMG NN * _NMG NN _NMG NN * stronger
NEGATIVE TURNING CHIPBREAKERS
Medium / Roughing Finishing
Material Group
* = 1st choice
Sharper edge X
Stronger edge
P
M
K
S
H
N (>8%Si)
_NMP NN
_NMA(Cast Iron Mat Group 7)
ALU(Aluminium <8% Si)
Light Cut,Stable Conditions
Roughing,Unstable Conditions
Additional dedicated geometries
Multi-MatTM Chipbreakers
NX _NMG NN NM
_NMA ALU
Negative Turning Chipbreakers: Recommendations
12
USER GUIDE
Special Design
A N
P
R
T
W
X
B
F
G
H
M
70°- 90°
70°- 90°
40°- 60°
40°- 60°
Type Symbol SymbolType
4. Fixing and Chipbreaker Types
2. Clearance Angle
A
B
C
D
E
F
G
N
P
O
Letter Symbol
3°
5°
7°
15°
20°
25°
30°
0°
11°
Special
g
A B C D
H K L
O P R
S T V W
G
M
1. Insert Shape
85° 82° 80° 55°
55°
86°
35°80°
D M S
A ± 0.005 ± 0.025± 0.025
C ± 0.025 ± 0.013 ± 0.025
E ± 0.025 ± 0.025 ± 0.025
F ± 0.013 ± 0.005 ± 0.025
G ± 0.025 ± 0.025 ± 0.130
H ± 0.013 ± 0.013 ± 0.025
± 0.025± 0.005± 0.05-0.15J*
± 0.025± 0.013± 0.05-0.15K*
± 0.025± 0.025± 0.05-0.15L*
± 0.130± 0.05-0.15 ± 0.08-0.20M*
± 0.025± 0.05-0.15 ± 0.08-0.20N*
± 0.08-0.25 ± 0.130± 0.13-0.38U*
3. Tolerance Class
Symbol
Ød
m
m
Ød
s
*Depending on the insert size. For exact tolerance see insert page.
dms
(mm)(mm)(mm)
m
Ød
A1
P22
K33
T44
W1
N22
M33
G44
Insert Designation (based on ISO norms)
13
USER GUIDE
1655
0466
PD77
T88
R99 10
Disregarding any decimals e.g. 12,7 = 12
L
L
L
L
L
L
L L
A, B, K C, D, E, M, V H, O, P
L R S
T W
5. Cutting Edge Length
R
00
M0
010204081216etc
= Sharp corner or round insert (inch version) = Round insert (metric version)
= 0.1 mm= 0.2 mm= 0.4 mm= 0.8 mm= 1.2 mm= 1.6 mm
7. Insert Corner Radius1st letter (Milling)
2nd letter (Milling)
ADEFPZ
ABCDEFGNPZ
= 45°= 60°= 75°= 85°= 90°= other
= 3°= 5°= 7°= 15°= 20°= 25°= 30°= 0°= 11°= other
6. Insert Thickness
SSS
01 = 1.59
T1 = 1.98
02 = 2.38
03 = 3.18
T3 = 3.97
04 = 4.76
05 = 5.56
06 = 6.35
07 = 7.94
09 = 9.52
S
Symbol mm
9. Cutting Direction
0855
0466
0877 88 99
NN10
e.g. Application (Milling)
- 45
- 90
- HF
45° Approach Angle90° Approach AngleHigh Feed
===
Optional information
10. Internal Designation
e.g. Chipbreaker (Turning)
Optional information
NN
NM
NX
PP
ALU
General purpose
Roughing operations
General purpose Magia
All purpose grooving
Non-ferrous materials
=====
R
L
N
Optional information
Turning
R
L
N
Optional information
Milling
Optional information
F
E
T
S
8. Edge Preparation
14
USER GUIDE
In order to obtain the best productivity using Lamina Technologies cutting tools, we have included some relevant comments and tips.
Each comment is represented by an icon and the relevant icons appear for each insert.
In machining stainless steel, please verify and respect the cutting speed recommended for the insert as there is a tendency to machine at speeds that are too low.
Stainless Steel
VC
In machining stainless steel or exotic materials, P geometry inserts (CNMP, TNMP, WNMP) and NX chipbreakers are recommended as first choice.
NX-CNMP-TNMP-WNMP
Stainless SteelExotic Material
In machining exotic materials, it is important to verify cutting conditions of the specific insert.
Exotic Material
Cutting Conditions!Verify
When milling materials from groups 1, 2, 3, 4, 6, 7, 8 and 11, coolant is not recommended. When machining materials from groups 5, 9, 10 and 12, it is recommended to use coolant.
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
To increase machining productivity, it is recommended to increase speed (Vc) while respecting chip size calculation.F
Productivity
VC
Productivity
To increase machining productivity, it is recommended to increase speed (Vc) while respecting chip size calculation.
Appropriate for boring operations.
It is important to verify and respect Amax, which is the maximum chip sec-tion. Feed x d.o.c. must be lower than the number noted as Amax.
Feed x d.o.c.=
Amax
P geometry inserts (CNMP, TNMP, WNMP) and NX chipbreakers are not recommended when machining with interrupted cut.
NXCNMPTNMPWNMP
Machining Recommendations
15
USER GUIDE
Symbol Designation Unit
Machining diameter mm
mm/rev
Machining length mm
Rotation rev/min
cm3/minChip removal rate
d.o.c x feed mm2
Nose radius mm
Dm
fn
lm
n
Q
Amax
r
Tc
Rmax
Cutting time
Surface roughness
min
μm
Feed per revolution
Vc Cutting speed m/min
ap Depth of cut (d.o.c.) mm
aeRadial depth of cut(width of cut) mm
D Cutter diameter mm
fz Feed per tooth mm/tooth
pcsZc
Vf Table Feed mm/min
pcsZn
Symbol Designation Unit
VcQ = x ap x fn
Vc =Dm x x n
1000
n =Vc x 1000
Dm x
Tc =lm
fn x n
Rmax = fn
2
x 125r
SurfaceRoughness(μm)
Cutting Time(min)
Rotation(Rev/min)
CuttingSpeed(m/min)
Chip RemovalRate(cm3/min)
Turning
fz =
Vcn =x 1000
x D
Vc = n x x D
1000
Q =ae x ap x Vf
1000
Vf = n x zc x fz
Feed per Tooth
Rotation(Rev/min)
CuttingSpeed(m/min)
Table Feed(mm/min)
Cutting Output(cm3/min)
Millling
Vf
n x zc
Total number of teeth
Effective number of teeth
Technical Formulas
16
USER GUIDE
Is it true that Lamina Technologies’ inserts can be used with any type of working material?
Lamina inserts have been tested in countless applications around the world and are suitable for practically any type of turning or milling metal cutting operation.
While Lamina inserts will work in aluminum pro-duction jobs, aluminum frequently requires tai-lored chip-control optimization. Please see Lam-ina’s dedicated aluminium line of inserts.
What speeds and feeds should Lamina inserts be run at?
In this catalog specific recommendations are provided for each individual insert indicating the speeds and feeds that are required for most of the material groups.
In order to achieve the maximum advantage from Lamina’s grade technology, it is important to always run the inserts according to the rec-ommended conditions.
In general, the best results are normally achieved at the high range of the recommended cutting speeds.
What can we expect regarding the quality and consistency of Lamina inserts?
Due to Lamina’s unique production methods and quality control procedures, you can expect inserts with higher accuracy and consistency than you have been accustomed up to now; in-sert to insert, box to box and batch to batch.
What percentage of my tooling requirements can Lamina supply?
In most regular shops, Lamina’s inserts program should cover about 80% of all inserts needed for CNC machines from 20 Hp and down. The insert program covers a full range of standard turning and milling operations from semi-roughing to su-per-finishing.
Will Lamina grades perform better than the specialized and dedicated grades available from the market?
Lamina has extensive know-how in sub-micron powder technology as well as in state of the art PVD coating. This know–how combined with unique chipbreaker geometry and in depth un-derstanding of the industry, enables Lamina to offer the Multi-MatTM Concept; a simple concept of using one insert to work on many materials.
The same insert can be used on the next job and the job after and so on, replacing the hun-dreds of specialized and confusing insert choic-es that are being used.
In machine shops that run Lamina inserts, what do they find as the biggest benefits?
• Time saving - Always have the right insert available for any job. This reduces the number of setups and idle time.• Cost saving - 80% reduction in insert inventory, ordering and stocking cost.
What about turning tool holders and boring bars?
Lamina’s ANSI / ISO standard turning inserts are designed to fit all industrial standard turning tools and boring bars, using the tool holders you have in your stock.
How does the 4 corners Alu-Line perform in low silicon aluminum?
Our Alu-Line insert’s geometry is specially de-signed for aluminum with low silicon content, creating chips that break instead of curl. The inserts are also coated and treated to reduce friction achieving unbeatable performance and tool life.
What is special about your solid end mill line?
Lamina know-how was applied to the solid end mill line. Our mills generate less friction and heat and therefore give better cut and longer tool life.
Frequently Asked Questions
17
TURNING
LT 10 | 1000LT 1005 | LT 1025
TURNING
CCMT
18
TURNING
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
LT 10 and LT 1000 LT 10 and LT 1000
Stainless Steel
VC
F M R
Application Guide
Insert Designation s r Catalog Nr.l
LT 10 Multi-MatTM General Usage – Standard
T00017761.204.7612CCMT 120412 NN LT 10
T00014570.804.7612CCMT 120408 NN LT 10
T00014560.404.7612CCMT 120404 NN LT 10
T00001170.803.979CCMT 09T308 NN LT 10
T00000560.403.979CCMT 09T304 NN LT 10
T00000550.402.386CCMT 060204 NN LT 10
TURNING
C C M T80° 7°
Shape Clearance Anglel
m
Tolerance
Ø d
s ± 0.13For l = 06/09, d ± 0.05 m ± 0.08 For l = 12, d ± 0.08 m ± 0.13
Fixing, Chipbreaker
s
F M R
Application Guide
Insert Designation s r Catalog Nr.l
LT 1000 Multi-MatTM General Usage – Premium
T00018931.20 4.7612CCMT 120412 NN LT 1000
T00018920.804.7612CCMT 120408 NN LT 1000
T00018910.404.7612CCMT 120404 NN LT 1000
T00018900.803.979CCMT 09T308 NN LT 1000
T00018890.403.979CCMT 09T304 NN LT 1000
T00018880.402.386CCMT 060204 NN LT 1000
80° diamond shape inserts with positive chipbreaker geometry. Very popular and useful for boring (even of small diameters), facing and external turning operations.
NN Chipbreaker
19
TURNINGMachining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.3 2.1 0.08 0.20 0.37 180 330 11.0 0.14 3300
2 190 HB 0.3 1.8 0.08 0.19 0.32 180 280 11.0 0.14 2260
3 250 HB 0.3 1.8 0.08 0.17 0.30 180 250 11.0 0.14 2240
6 180 HB 0.3 1.8 0.08 0.17 0.31 120 280 11.0 0.11 2260
4,6 230 HB 0.3 1.8 0.08 0.17 0.30 120 250 11.0 0.11 2240
5,7 280 HB 0.3 1.4 0.08 0.15 0.25 120 210 11.0 0.10 2200
8 350 HB 0.3 1.4 0.08 0.15 0.22 120 180 11.0 0.10 1180
10 220 HB 0.3 1.8 0.07 0.15 0.25 70 190 00.9 0.08 1180
10 280 HB 0.3 1.8 0.07 0.14 0.25 70 150 00.9 0.08 1140
11 320 HB 0.3 1.4 0.07 0.12 0.20 70 130 00.9 0.08 1120
11 350 HB 0.3 1.4 0.07 0.12 0.16 70 110 00.9 0.08 1110
14 180 HB 0.3 1.8 0.06 0.15 0.20 170 270 11.0 0.07 2260
14 240 HB 0.3 1.8 0.06 0.15 0.16 160 220 11.0 0.06 2210
14 290 HB 0.3 1.4 0.06 0.12 0.12 80 150 00.9 0.06 1140
14 310 HB 0.3 1.4 0.06 0.12 0.12 70 140 00.9 0.06 1140
12 200 HB 0.3 1.8 0.06 0.15 0.20 170 250 00.9 0.07 2240
13 42 HRc 0.3 1.4 0.06 0.14 0.16 120 190 00.8 0.06 1180
15 150 HB 0.3 2.1 0.06 0.17 0.40 170 250 11.0 0.14 2240
15 200 HB 0.3 2.1 0.06 0.17 0.37 160 230 11.0 0.14 2220
16 250 HB 0.3 2.1 0.06 0.17 0.37 150 210 11.0 0.14 2200
17,19 150 HB 0.3 1.8 0.06 0.15 0.30 120 250 11.0 0.10 2240
17,19 200 HB 0.3 1.8 0.06 0.15 0.25 120 230 11.0 0.10 2220
18,20 250 HB 0.3 1.8 0.06 0.15 0.25 120 190 11.0 0.10 1180
31,32 Incoloy 800 240 HB 0.3 1.4 0.07 0.13 0.16 25 50 00.7 0.08 440
33 Inconel 700 250 HB 0.3 1.4 0.07 0.13 0.16 25 50 00.7 0.08 440
34 Stellite 21 350 HB 0.3 1.4 0.07 0.13 0.16 23 45 00.7 0.08 335
36 TiAl6V4 - 0.3 1.4 0.07 0.14 0.20 45 65 00.7 0.11 660
37 T40 - 0.3 1.4 0.07 0.12 0.16 35 60 00.7 0.08 550
38 45 HRc 0.3 1.3 0.04 0.10 0.12 50 100 00.7 0.08 990
38 50 HRc 0.3 1.1 0.04 0.09 0.11 40 90 00.6 0.06 880
38 55 HRc 0.0 1.0 0.04 0.08 0.08 40 80 00.5 0.05 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.1 0.04 0.10 0.11 40 60 00.6 0.08 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.0 0.04 0.08 0.08 30 50 00.5 0.05 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 2.8 0.08 0.26 0.43 200 400 1.0 0.18 350
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
CCMT 060204 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
20
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300
2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260
3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240
6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260
4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240
5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200
8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180
10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180
10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140
11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120
11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110
14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260
14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210
14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140
14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140
12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240
13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180
15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240
15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220
16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200
17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240
17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220
18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335
36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660
37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550
38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990
38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880
38 55 HRc 0.0 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 00.9 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
CCMT 09T304 NN – LT 10 | LT 1000
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
21
TURNINGMachining Conditions
1 125 HB 0.5 4.0 0.2 0.5 2 180 330 22.7 0.3 2240
2 190 HB 0.5 4.0 0.2 0.5 2 180 280 22.7 0.3 2220
3 250 HB 0.5 4.0 0.2 0.5 1 180 250 22.7 0.3 2200
6 180 HB 0.5 4.0 0.2 0.5 1 120 280 22.7 0.3 2200
4,6 230 HB 0.5 3.2 0.2 0.5 1 120 250 22.7 0.3 1180
5,7 280 HB 0.5 3.2 0.2 0.4 1 120 210 22.7 0.3 1150
8 350 HB 0.5 2.8 0.2 0.4 1 120 180 22.7 0.3 1130
10 220 HB 0.5 3.2 0.2 0.4 1 70 190 22.3 0.3 1140
10 280 HB 0.5 3.2 0.2 0.4 1 70 150 22.3 0.3 1120
11 320 HB 0.5 2.4 0.2 0.4 1 70 130 22.3 0.3 1100
11 350 HB 0.5 2.4 0.2 0.4 1 70 110 22.3 0.3 990
14 180 HB 0.5 4.0 0.2 0.4 1 170 270 22.7 0.2 1190
14 240 HB 0.5 4.0 0.2 0.4 1 160 220 22.7 0.2 1170
14 290 HB 0.5 3.2 0.2 0.4 1 80 150 22.3 0.2 1100
14 310 HB 0.5 3.2 0.2 0.4 1 70 140 22.3 0.2 990
12 200 HB 0.5 4.0 0.2 0.4 1 170 250 22.3 0.2 1190
13 42 HRc 0.5 3.2 0.2 0.4 1 120 190 22.0 0.2 1130
15 150 HB 0.5 4.0 0.2 0.6 2 170 250 22.7 0.3 2200
15 200 HB 0.5 4.0 0.2 0.6 2 160 230 22.7 0.3 1180
16 250 HB 0.5 4.0 0.2 0.6 2 150 210 22.7 0.3 1160
17,19 150 HB 0.5 4.0 0.2 0.5 1 120 250 22.7 0.3 1180
17, 19 200 HB 0.5 4.0 0.2 0.5 1 120 230 22.7 0.3 1160
18,20 250 HB 0.5 4.0 0.2 0.5 1 120 190 22.7 0.3 1140
31,32 Incoloy 800 240 HB 0.5 2.4 0.2 0.4 1 30 50 11.8 0.3 332
33 Inconel 700 250 HB 0.5 2.4 0.2 0.4 1 30 50 11.8 0.3 330
34 Stellite 21 350 HB 0.5 2.4 0.2 0.4 1 20 40 11.8 0.3 228
37 T40 - 0.5 2.4 0.2 0.4 1 40 60 11.8 0.3 445
36 TiAI6V4 - 0.5 3.2 0.2 0.4 1 50 70 11.8 0.3 555
41 55 HRc 0.5 1.2 0.1 0.2 0 30 50 00.9 0.1 440
40 400 HB 0.5 1.6 0.1 0.3 0 40 60 11.4 0.2 550
38 45 HRc 0.5 2.0 0.1 0.3 1 50 100 11.8 0.2 880
38 Ni-Hard 2 50 HRc 0.5 1.6 0.1 0.3 0 40 90 11.4 0.2 770
38 G-X300CrMo15 55 HRc 0.5 1.2 0.1 0.2 0.3 40.0 80.0 00.9 0.2 660
12 25 AlSi12 130 HB 0.5 4.8 0.2 0.6 2 200 400 2.7 0.4 280
X100CrMo13, 440C,
G-X260NiCr42
410, X6Cr17, 17-4 PH, 430
GG20, GG40, EN-GJL-250, N030B
GGG40, GGG70, 50005
11
C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
X40CrM0V5, H13, M42, D3, S6-5-2,
12Ni19
304, 316, X5CrNi18-9
X2CrNiN23-4, S31500
8
9
10
6
7
4
5
3
1
2
CCMT 09T308 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
22
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300
2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260
3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240
6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260
4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240
5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200
8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180
10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180
10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140
11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120
11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110
14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260
14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210
14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140
14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140
12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240
13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180
15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240
15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220
16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200
17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240
17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220
18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335
36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660
37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550
38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990
38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880
38 55 HRc 0.0 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 00.9 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
CCMT 120404 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
23
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240
2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220
3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200
6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150
8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130
10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140
10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120
11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100
11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990
14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190
14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170
14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100
14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990
12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190
13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130
15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200
15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180
16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332
33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330
34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228
36 TiAl6V4 - 0.5 4.0 0.20 0.40 0.80 45 65 22.0 0.33 555
37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445
38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880
38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770
38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.25 0.40 40 60 11.5 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.20 0.30 30 50 11.0 0.15 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 3.0 0.40 280
St
eel
Non-alloyed
Low alloyed
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
10
8
CCMT 120408 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
24
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.60 2.16 180 330 33.0 0.42 2240
2 190 HB 0.5 5.0 0.21 0.60 2.16 180 280 33.0 0.42 2220
3 250 HB 0.5 5.0 0.21 0.54 1.80 180 250 33.0 0.42 2200
6 180 HB 0.5 5.0 0.21 0.54 1.44 120 280 33.0 0.38 2200
4,6 230 HB 0.5 4.0 0.21 0.54 1.44 120 250 33.0 0.38 1180
5,7 280 HB 0.5 4.0 0.18 0.48 1.44 120 210 33.0 0.36 1150
8 350 HB 0.5 3.5 0.18 0.48 1.20 120 180 33.0 0.36 1130
10 220 HB 0.5 4.0 0.18 0.48 1.44 70 190 22.5 0.36 1140
10 280 HB 0.5 4.0 0.18 0.48 1.44 70 150 22.5 0.36 1120
11 320 HB 0.5 3.0 0.18 0.42 0.96 70 130 22.5 0.34 1100
11 350 HB 0.5 3.0 0.18 0.42 0.96 70 110 22.5 0.34 990
14 180 HB 0.5 5.0 0.20 0.48 1.44 170 270 33.0 0.35 1190
14 240 HB 0.5 5.0 0.20 0.48 1.20 160 220 33.0 0.35 1170
14 290 HB 0.5 4.0 0.18 0.42 0.96 80 150 22.5 0.28 1100
14 310 HB 0.5 4.0 0.18 0.42 0.96 70 140 22.5 0.28 990
12 200 HB 0.5 5.0 0.22 0.48 1.20 170 250 33.0 0.35 1190
13 42 HRc 0.5 4.0 0.22 0.48 1.20 120 190 22.5 0.35 1130
15 150 HB 0.5 5.0 0.15 0.72 2.40 170 250 33.0 0.42 2200
15 200 HB 0.5 5.0 0.15 0.72 2.16 160 230 33.0 0.42 1180
16 250 HB 0.5 5.0 0.15 0.66 2.16 150 210 33.0 0.42 1160
17,19 150 HB 0.5 5.0 0.15 0.60 1.80 120 250 33.0 0.36 1180
17,19 200 HB 0.5 5.0 0.15 0.60 1.56 120 230 33.0 0.36 1160
18,20 250 HB 0.5 5.0 0.15 0.60 1.44 120 190 33.0 0.36 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.42 0.84 25 45 22.0 0.30 332
33 Inconel 700 250 HB 0.5 3.0 0.20 0.42 0.84 25 45 22.0 0.30 330
34 Stellite 21 350 HB 0.5 3.0 0.20 0.42 0.84 23 40 22.0 0.30 228
36 TiAl6V4 - 0.5 4.0 0.20 0.48 0.96 45 65 22.0 0.35 555
37 T40 - 0.5 3.0 0.20 0.42 0.84 35 55 22.0 0.30 445
38 45 HRc 0.5 2.5 0.11 0.36 0.72 50 100 22.0 0.30 880
38 50 HRc 0.5 2.0 0.11 0.30 0.48 40 90 11.5 0.24 770
38 55 HRc 0.5 1.5 0.11 0.24 0.36 40 80 11.0 0.22 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.30 0.48 40 60 11.5 0.22 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.24 0.36 30 50 11.0 0.18 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.72 2.20 200 400 3.0 0.48 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
7 GG20, GG40, EN-GJL-250,
No30B
10
8
6 410, X6Cr17, 17-4 PH, 430
4304, 316,
X5CrNi18-9
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
1C35, Ck45, 1020, 1045, 1060, 28Mn6
CCMT 120412 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
25
TURNING
VC
Productivity
FProductivity
C N M A80° 0°
Shape Clearance Angles
Ø d
l
m
Toleranced ± 0.08m ± 0.13s ± 0.13
Fixing,Chipbreaker
Strong edge preparation mainly for gray cast iron. For general purpose turning, facing and boring opera-tions.
F M RInsert Designation s r Catalog Nr.l
LT 1005 Recommended for moderate to high speed
T00040511.24.7612CNMA 120412 LT 1005
T00040500.84.7612CNMA 120408 LT 1005
Application Guide
CNMA
26
TURNING Machining Conditions
CNMA 120408 – LT 1005
CNMA 120412 – LT 1005
min max min max min max D.O.C. Feed Vc
15 150 HB 0.7 6.0 0.20 0.60 1.7 270 450 33.5 0.40 3350
15 200 HB 0.7 6.0 0.20 0.58 1.5 200 320 33.5 0.40 2250
16 250 HB 0.7 6.0 0.20 0.56 1.5 170 240 33.5 0.40 2220
17,19 150 HB 0.7 6.0 0.20 0.52 1.3 130 260 33.0 0.30 2240
17,19 200 HB 0.7 6.0 0.20 0.50 1.1 130 230 33.0 0.30 2210
18,20 250 HB 0.7 6.0 0.20 0.48 1.0 130 190 33.0 0.30 1180
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.4 0.14 0.25 0.3 40 60 11.5 0.19 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.8 0.14 0.20 0.3 30 50 11.2 0.17 440
GGG40, GGG70, 50005
Amax [mm ]
Gr. N°VDI
GroupMaterial Examples* Hardness
7 GG20, GG40, EN-GJL-250,
No30B
8
min max min max min max D.O.C. Feed
15 150 HB 0.7 6.0 0.20 0.40 1.4 270 450 33.5 0.32 3350
15 200 HB 0.7 6.0 0.20 0.38 1.2 200 320 33.5 0.32 2250
16 250 HB 0.7 6.0 0.20 0.36 1.2 170 240 33.5 0.32 2220
17,19 150 HB 0.7 6.0 0.20 0.40 1.0 130 260 22.5 0.30 2240
17,19 200 HB 0.7 6.0 0.20 0.38 0.9 130 230 22.5 0.30 2210
18,20 250 HB 0.7 6.0 0.20 0.36 0.8 130 190 22.5 0.30 1180
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.4 0.14 0.20 0.3 40 60 11.4 0.16 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.8 0.14 0.20 0.2 30 50 11.1 0.15 44011
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm]Feed
[mm/rev] Amax[mm2]
Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm]Feed
[mm/rev] Amax[mm2]
Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Cast
Iron
Grey
Malleable & Nodular
H
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Cast
Iron
Grey
Malleable & Nodular
H
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Cast
Iron
Grey
Malleable & Nodular
H
Chilled Cast Iron
White Cast Iron
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
27
TURNING
LT 10 and LT 1000
NX LT 10 and LT 1000 NX LT 10 and LT 1000
LT 10 and LT 1000
NX-CNMP-TNMP-WNMP
Stainless SteelExotic Material Exotic Material
Cutting Conditions!Verify
FProductivity
Stainless Steel
VC
C N M G80° 0°
Shape Clearance Anglel
m
Toleranced ± 0.08m ± 0.13s ± 0.13
Ø d
Fixing,Chipbreaker
ss
F M RInsert Designation s r Catalog Nr.l
LT 10 Multi-MatTM General Usage – Standard
T00000611.204.7612CNMG 120412 NN LT 10
T00019660.804.7612CNMG 120408 NM LT 10
T00000590.804.7612CNMG 120408 NN LT 10
T00004910.404.7612CNMG 120404 NN LT 10
Application Guide
F M R
Application Guide
Insert Designation s r Catalog Nr.l
LT 1000 Multi-MatTM General Usage – Premium
T00018971.204.7612CNMG 120412 NN LT 1000
T00027410.804.7612CNMG 120408 NX LT 1000
T00019680.804.7612CNMG 120408 NM LT 1000
T00018960.804.7612CNMG 120408 NN LT 1000
T00018950.404.7612CNMG 120404 NN LT 1000
The most popular general purpose turning inserts. Use for turning, facing and boring operations.
NX chipbreaker NM chipbreaker NN chipbreaker
NN chipbreaker
CNMG
28
TURNING
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00040561.204.7612CNMG 120412 NN LT 1005
T00040550.804.7612CNMG 120408 NX LT 1005
T00040530.804.7612CNMG 120408 NM LT 1005
T00040540.804.7612CNMG 120408 NN LT 1005
LT 1005 Recommended for moderate to high speed
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00041141.204.7612CNMG 120412 NN LT 1025
T00041130.804.7612CNMG 120408 NX LT 1025
T00041110.804.7612CNMG 120408 NM LT 1025
T00041120.804.7612CNMG 120408 NN LT 1025
LT 1025 Recommended for moderate to low speed
NX for LT 1025 LT 1005
NX-CNMP-TNMP-WNMP
Stainless SteelExotic Material VC
Productivity
The most popular general purpose turning inserts. Use for turning, facing and boring operations.
NX chipbreaker NM chipbreaker NN chipbreaker
C N M G
29
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300
2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260
3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240
6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260
4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240
5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200
8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180
10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180
10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140
11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120
11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110
14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260
14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210
14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140
14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140
12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240
13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180
15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240
15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220
16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200
17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240
17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220
18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335
36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660
37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550
38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990
38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880
38 55 HRc 0.0 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 00.9 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
7 GG20, GG40, EN-GJL-250,
No30B
8
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
CNMG 120404 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
30
TURNING Machining Conditions
1 125 HB 0.5 5.0 0.2 0.5 1.8 180 330 33.0 0.4 2240
2 190 HB 0.5 5.0 0.2 0.5 1.8 180 280 33.0 0.4 2220
3 250 HB 0.5 5.0 0.2 0.5 1.5 180 250 33.0 0.3 2200
6 180 HB 0.5 5.0 0.2 0.5 1.2 120 280 33.0 0.3 2200
4,6 230 HB 0.5 4.0 0.2 0.5 1.2 120 250 33.0 0.3 1180
5,7 280 HB 0.5 4.0 0.2 0.4 1.2 120 210 33.0 0.3 1150
8 350 HB 0.5 3.5 0.2 0.4 1.0 120 180 22.7 0.3 1130
10 220 HB 0.5 4.0 0.2 0.4 1.2 70 190 22.5 0.3 1140
10 280 HB 0.5 4.0 0.2 0.4 1.2 70 150 22.5 0.3 1120
11 320 HB 0.5 3.0 0.2 0.4 0.8 70 130 22.2 0.3 1100
11 350 HB 0.5 3.0 0.2 0.4 0.8 70 110 22.2 0.3 990
14 180 HB 0.5 5.0 0.2 0.4 1.2 170 270 33.0 0.3 1190
14 240 HB 0.5 5.0 0.2 0.4 1.0 160 220 33.0 0.2 1170
14 290 HB 0.5 4.0 0.2 0.4 0.8 80 150 22.5 0.2 1100
14 310 HB 0.5 4.0 0.2 0.4 0.8 70 140 22.5 0.2 990
12 200 HB 0.5 5.0 0.2 0.4 0.7 170 250 22.5 0.2 1190
13 42 HRc 0.5 4.0 0.2 0.4 0.7 120 190 22.2 0.2 1130
15 150 HB 0.5 5.0 0.2 0.6 2.0 170 250 33.0 0.4 2200
15 200 HB 0.5 5.0 0.2 0.6 1.8 160 230 33.0 0.4 1180
16 250 HB 0.5 5.0 0.2 0.6 1.8 150 210 33.0 0.4 1160
17,19 150 HB 0.5 5.0 0.2 0.5 1.5 120 250 33.0 0.3 1180
17, 19 200 HB 0.5 5.0 0.2 0.5 1.3 120 230 33.0 0.3 1160
18,20 250 HB 0.5 5.0 0.2 0.5 1.2 120 190 33.0 0.3 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.2 0.4 0.7 30 50 22.0 0.3 332
33 Inconel 700 250 HB 0.5 3.0 0.2 0.4 0.7 30 50 22.0 0.3 330
34 Stellite 21 350 HB 0.5 3.0 0.2 0.4 0.7 20 40 22.0 0.3 228
37 T40 - 0.5 3.0 0.2 0.4 0.7 40 60 22.0 0.3 445
36 TiAI6V4 - 0.5 3.5 0.2 0.4 0.8 50 70 22.0 0.3 555
41 55 HRc 0.5 1.5 0.1 0.2 0.3 30 50 11.0 0.2 440
40 400 HB 0.5 2.0 0.1 0.3 0.4 40 60 11.5 0.2 550
38 45 HRc 0.5 2.5 0.1 0.3 0.6 50 100 22.0 0.3 880
38 Ni-Hard 2 50 HRc 0.5 2.0 0.1 0.3 0.4 40 90 11.5 0.2 770
38 G-X300CrMo15 55 HRc 0.5 1.5 0.1 0.2 0.3 40.0 80.0 11.0 0.2 660
12 25 AlSi12 130 HB 0.5 6.0 0.2 0.6 1.8 200 400 3.0 0.4 280
3X40CrM0V5, H13, M42, D3, S6-5-2,
12Ni19
1C35, Ck45, 1020,
1045, 1060, 28Mn6
242CrMo4, St50,
Ck60, 4140, 4340, 100Cr6
6410, X6Cr17, 17-4
PH, 430
7GG20, GG40, EN-GJL-250, N030B
4304, 316, X5CrNi18-
9
5X2CrNiN23-4,
S31500
X100CrMo13, 440C,
G-X260NiCr42 11
8GGG40, GGG70,
50005
9
10
CNMG 120408 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
31
TURNINGMachining Conditions
CNMG 120408 NN – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.50 1.80 180 430 33.0 0.38 2265
2 190 HB 0.5 5.0 0.21 0.50 1.80 180 365 33.0 0.35 2240
3 250 HB 0.5 5.0 0.21 0.45 1.50 180 325 33.0 0.33 2220
6 180 HB 0.5 5.0 0.21 0.45 1.20 120 365 33.0 0.32 2220
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 325 33.0 0.32 2200
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 275 33.0 0.30 1165
8 350 HB 0.5 3.5 0.18 0.40 1.00 120 235 22.7 0.30 1145
10 220 HB 0.5 4.0 0.18 0.40 1.20 70 245 22.5 0.30 1155
10 280 HB 0.5 4.0 0.18 0.40 1.20 70 195 22.5 0.30 1130
11 320 HB 0.5 3.0 0.18 0.35 0.80 70 170 22.2 0.28 1110
11 350 HB 0.5 3.0 0.18 0.35 0.80 70 145 22.2 0.28 1100
15 150 HB 0.5 5.0 0.15 0.60 2.00 170 325 33.0 0.35 2220
15 200 HB 0.5 5.0 0.15 0.60 1.80 160 300 33.0 0.35 2200
16 250 HB 0.5 5.0 0.15 0.55 1.80 150 275 33.0 0.35 1175
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 325 33.0 0.30 2200
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 300 33.0 0.30 1175
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 245 33.0 0.30 1155
38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 130 22.0 0.25 990
38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 115 11.5 0.20 775
38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 105 11.0 0.18 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.25 0.40 40 80 11.5 0.18 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.20 0.30 30 65 11.0 0.15 445
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
32
TURNING Machining Conditions
CNMG 120408 NN – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.50 1.8 90 330 33.0 0.38 2240
2 190 HB 0.5 5.0 0.21 0.50 1.8 90 280 33.0 0.35 2220
3 250 HB 0.5 5.0 0.21 0.45 1.5 90 250 33.0 0.33 2200
6 180 HB 0.5 5.0 0.21 0.45 1.2 60 280 33.0 0.32 2200
4,6 230 HB 0.5 4.0 0.21 0.45 1.2 60 250 33.0 0.32 1180
5,7 280 HB 0.5 4.0 0.18 0.40 1.2 60 210 33.0 0.30 1150
8 350 HB 0.5 3.5 0.18 0.40 1.0 60 180 22.7 0.30 1130
10 220 HB 0.5 4.0 0.18 0.40 1.2 35 190 22.5 0.30 1140
10 280 HB 0.5 4.0 0.18 0.40 1.2 35 150 22.5 0.30 1120
11 320 HB 0.5 3.0 0.18 0.35 0.8 35 130 22.2 0.28 1100
11 350 HB 0.5 3.0 0.18 0.35 0.8 35 110 22.2 0.28 990
14 180 HB 0.5 5.0 0.20 0.40 1.20 85 270 33.0 0.25 1190
14 240 HB 0.5 5.0 0.20 0.40 1.00 80 220 33.0 0.22 1170
14 290 HB 0.5 4.0 0.18 0.35 0.80 40 150 22.5 0.24 1100
14 310 HB 0.5 4.0 0.18 0.35 0.80 35 140 22.5 0.24 990
12 200 HB 0.5 5.0 0.18 0.40 0.70 85 250 22.5 0.20 1190
13 42 HRc 0.5 4.0 0.18 0.40 0.70 60 190 22.2 0.20 1130
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 60 250 33.0 0.30 1180
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 60 230 33.0 0.30 1160
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 60 190 33.0 0.30 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
33
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.65 2.70 180 330 44.0 0.50 2210
2 190 HB 0.5 5.0 0.21 0.65 2.70 180 280 44.0 0.50 2200
3 250 HB 0.5 5.0 0.21 0.59 2.25 180 250 44.0 0.50 2200
6 180 HB 0.5 5.0 0.21 0.59 1.80 120 280 44.0 0.44 1160
4,6 230 HB 0.5 4.0 0.21 0.59 1.80 120 250 44.0 0.44 1150
5,7 280 HB 0.5 4.0 0.18 0.52 1.80 120 210 44.0 0.38 1140
8 350 HB 0.5 3.5 0.18 0.52 1.60 120 180 44.0 0.38 1130
10 220 HB 0.5 4.0 0.18 0.52 1.80 70 190 33.3 0.38 1120
10 280 HB 0.5 4.0 0.18 0.52 1.80 70 150 33.3 0.38 1110
11 320 HB 0.5 3.0 0.18 0.46 1.20 70 130 33.3 0.35 1100
11 350 HB 0.5 3.0 0.18 0.46 1.20 70 110 33.3 0.35 990
14 180 HB 0.5 5.0 0.20 0.52 1.80 170 270 44.0 0.38 1190
14 240 HB 0.5 5.0 0.20 0.52 1.60 160 220 44.0 0.38 1170
14 290 HB 0.5 4.0 0.18 0.46 1.20 80 150 33.3 0.32 1100
14 310 HB 0.5 4.0 0.18 0.46 1.20 70 140 33.3 0.32 990
12 200 HB 0.5 5.0 0.22 0.52 1.60 170 250 44.0 0.38 1190
13 42 HRc 0.5 4.0 0.22 0.52 1.60 120 190 33.5 0.38 1130
15 150 HB 0.5 5.0 0.15 0.78 3.00 170 250 44.0 0.44 1180
15 200 HB 0.5 5.0 0.15 0.78 2.70 160 230 44.0 0.44 1170
16 250 HB 0.5 5.0 0.15 0.72 2.70 150 210 44.0 0.44 1160
17,19 150 HB 0.5 5.0 0.15 0.65 2.25 120 250 44.0 0.38 1150
17,19 200 HB 0.5 5.0 0.15 0.65 1.95 120 230 44.0 0.38 1140
18,20 250 HB 0.5 5.0 0.15 0.65 1.80 120 190 44.0 0.38 1130
31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.46 1.05 25 45 22.7 0.35 330
33 Inconel 700 250 HB 0.5 3.0 0.20 0.46 1.05 25 45 22.7 0.35 332
34 Stellite 21 350 HB 0.5 3.0 0.20 0.46 1.05 23 40 22.7 0.35 228
36 TiAl6V4 - 0.5 4.0 0.20 0.52 1.20 45 65 22.7 0.38 555
37 T40 - 0.5 3.0 0.20 0.46 1.05 35 55 22.7 0.36 445
38 45 HRc 0.5 2.5 0.11 0.39 0.90 50 100 22.7 0.31 880
38 50 HRc 0.5 2.0 0.11 0.33 0.60 40 90 22.0 0.25 770
38 55 HRc 0.5 1.5 0.11 0.26 0.45 40 80 11.5 0.23 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.33 0.60 40 60 22.0 0.23 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.26 0.45 30 50 11.5 0.19 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.78 2.70 200 400 4.0 0.50 280
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
CNMG 120408 NM – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
34
TURNING Machining Conditions
CNMG 120408 NM – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.65 2.70 180 430 33.6 0.46 2265
2 190 HB 0.5 5.0 0.21 0.65 2.70 180 365 33.6 0.42 2240
3 250 HB 0.5 5.0 0.21 0.59 2.25 180 325 33.6 0.40 2220
6 180 HB 0.5 5.0 0.21 0.59 1.80 120 365 33.6 0.38 2220
4,6 230 HB 0.5 4.0 0.21 0.59 1.80 120 325 33.6 0.38 2200
5,7 280 HB 0.5 4.0 0.18 0.52 1.80 120 275 33.6 0.36 1165
8 350 HB 0.5 3.5 0.18 0.52 1.50 120 235 33.2 0.36 1145
10 220 HB 0.5 4.0 0.18 0.52 1.80 70 245 33.0 0.36 1155
10 280 HB 0.5 4.0 0.18 0.52 1.80 70 195 33.0 0.36 1130
11 320 HB 0.5 3.0 0.18 0.46 1.20 70 170 22.6 0.34 1110
11 350 HB 0.5 3.0 0.18 0.46 1.20 70 145 22.6 0.34 1100
15 150 HB 0.5 5.0 0.15 0.78 3.00 170 325 33.6 0.42 2220
15 200 HB 0.5 5.0 0.15 0.78 2.70 160 300 33.6 0.42 2200
16 250 HB 0.5 5.0 0.15 0.72 2.70 150 275 33.6 0.42 1175
17,19 150 HB 0.5 5.0 0.15 0.65 2.25 120 325 33.6 0.36 2200
17,19 200 HB 0.5 5.0 0.15 0.65 1.95 120 300 33.6 0.36 1175
18,20 250 HB 0.5 5.0 0.15 0.65 1.80 120 245 33.6 0.36 1155
38 45 HRc 0.5 2.5 0.11 0.39 0.90 50 130 22.4 0.30 990
38 50 HRc 0.5 2.0 0.11 0.33 0.60 40 115 11.8 0.24 775
38 55 HRc 0.5 1.5 0.11 0.26 0.45 40 105 11.2 0.22 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.33 0.60 40 80 11.8 0.22 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.26 0.45 30 65 11.2 0.18 445
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
7 GG20, GG40, EN-GJL-250,
No30B
8
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
CNMG 120408 NM – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.65 2.7 90 330 44.0 0.50 2210
2 190 HB 0.5 5.0 0.21 0.65 2.7 90 280 44.0 0.50 2200
3 250 HB 0.5 5.0 0.21 0.59 2.3 90 250 44.0 0.50 2200
6 180 HB 0.5 5.0 0.21 0.59 1.8 60 280 44.0 0.44 1160
4,6 230 HB 0.5 4.0 0.21 0.59 1.8 60 250 44.0 0.44 1150
5,7 280 HB 0.5 4.0 0.18 0.52 1.8 60 210 44.0 0.38 1140
8 350 HB 0.5 3.5 0.18 0.52 1.6 60 180 44.0 0.38 1130
10 220 HB 0.5 4.0 0.18 0.52 1.8 35 190 33.3 0.38 1120
10 280 HB 0.5 4.0 0.18 0.52 1.8 35 150 33.3 0.38 1110
11 320 HB 0.5 3.0 0.18 0.46 1.2 35 130 33.3 0.35 1100
11 350 HB 0.5 3.0 0.18 0.46 1.2 35 110 33.3 0.35 990
12 200 HB 0.5 5.0 0.22 0.52 1.6 85 250 44.0 0.38 1190
13 42 HRc 0.5 4.0 0.22 0.52 1.6 60 190 33.5 0.38 1130
17,19 150 HB 0.5 5.0 0.15 0.65 2.3 60 250 44.0 0.38 1150
17,19 200 HB 0.5 5.0 0.15 0.65 2.0 60 230 44.0 0.38 1140
18,20 250 HB 0.5 5.0 0.15 0.65 1.8 60 190 44.0 0.38 1130
8GGG40, GGG70,
50005
410, X6Cr17, 17-4 PH, 430
6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
35
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.18 0.50 1.70 180 330 33.0 0.33 2240
2 190 HB 0.5 5.0 0.18 0.50 1.70 180 280 33.0 0.33 2220
3 250 HB 0.5 5.0 0.18 0.45 1.45 180 250 33.0 0.33 2200
6 180 HB 0.5 5.0 0.18 0.45 1.15 120 280 33.0 0.30 2200
4,6 230 HB 0.5 4.0 0.18 0.45 1.15 120 250 33.0 0.30 1180
5,7 280 HB 0.5 4.0 0.16 0.40 1.15 120 210 33.0 0.29 1150
8 350 HB 0.5 3.5 0.16 0.40 0.95 120 180 33.0 0.29 1130
10 220 HB 0.5 4.0 0.16 0.40 1.15 70 190 22.5 0.29 1140
10 280 HB 0.5 4.0 0.16 0.40 1.15 70 150 22.5 0.29 1120
11 320 HB 0.5 3.0 0.16 0.35 0.75 70 130 22.5 0.27 1100
11 350 HB 0.5 3.0 0.16 0.35 0.75 70 110 22.5 0.27 990
14 180 HB 0.5 5.0 0.18 0.40 1.15 170 270 33.0 0.24 1190
14 240 HB 0.5 5.0 0.18 0.40 0.95 160 220 33.0 0.21 1170
14 290 HB 0.5 4.0 0.16 0.35 0.75 80 150 22.5 0.27 1100
14 310 HB 0.5 4.0 0.16 0.35 0.75 70 140 22.5 0.27 990
12 200 HB 0.5 5.0 0.19 0.40 0.95 170 250 22.5 0.29 1190
13 42 HRc 0.5 4.0 0.19 0.40 0.95 120 190 22.2 0.24 1130
15 150 HB 0.5 5.0 0.13 0.60 1.90 170 250 33.0 0.33 2200
15 200 HB 0.5 5.0 0.13 0.60 1.70 160 230 33.0 0.33 1180
16 250 HB 0.5 5.0 0.13 0.55 1.70 150 210 33.0 0.33 1160
17,19 150 HB 0.5 5.0 0.13 0.50 1.45 120 250 33.0 0.29 1180
17,19 200 HB 0.5 5.0 0.13 0.50 1.25 120 230 33.0 0.29 1160
18,20 250 HB 0.5 5.0 0.13 0.50 1.15 120 190 33.0 0.29 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.18 0.35 0.65 25 45 22.0 0.27 330
33 Inconel 700 250 HB 0.5 3.0 0.18 0.35 0.65 25 45 22.0 0.27 330
34 Stellite 21 350 HB 0.5 3.0 0.18 0.35 0.65 25 40 22.0 0.27 330
36 TiAl6V4 - 0.5 4.0 0.18 0.40 0.75 45 65 22.0 0.31 555
37 T40 - 0.5 3.0 0.18 0.35 0.65 35 55 22.0 0.29 445
38 45 HRc 0.5 2.5 0.10 0.30 0.55 50 100 22.0 0.24 880
38 50 HRc 0.5 2.0 0.10 0.25 0.40 40 90 11.5 0.19 770
38 55 HRc 0.5 1.5 0.10 0.20 0.30 40 80 11.0 0.17 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.10 0.25 0.40 40 60 11.5 0.17 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.20 0.30 30 50 11.0 0.14 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.18 0.60 1.70 200 400 33.0 0.38 280
3
2
X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
7 GG20, GG40, EN-GJL-250,
No30B
5X2CrNiN23-4,
S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
High alloyed
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
Cast
Iron
Grey
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
Malleable & Nodular 8GGG40, GGG70,
50005
CNMG 120408 NX – LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
36
TURNING Machining Conditions
CNMG 120408 NX – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.18 0.50 1.7 90 330 33.0 0.36 2240
2 190 HB 0.5 5.0 0.18 0.50 1.7 90 280 33.0 0.33 2220
3 250 HB 0.5 5.0 0.18 0.45 1.4 90 250 33.0 0.31 2200
6 180 HB 0.5 5.0 0.18 0.45 1.1 60 280 33.0 0.30 2200
4,6 230 HB 0.5 4.0 0.18 0.45 1.1 60 250 33.0 0.30 1180
5,7 280 HB 0.5 4.0 0.16 0.40 1.1 60 210 33.0 0.29 1150
8 350 HB 0.5 3.5 0.16 0.40 1.0 60 180 22.7 0.29 1130
10 220 HB 0.5 4.0 0.16 0.40 1.1 35 190 22.5 0.29 1140
10 280 HB 0.5 4.0 0.16 0.40 1.1 35 150 22.5 0.29 1120
11 320 HB 0.5 3.0 0.16 0.35 0.8 35 130 22.2 0.27 1100
11 350 HB 0.5 3.0 0.16 0.35 0.8 35 110 22.2 0.27 990
14 180 HB 0.5 5.0 0.18 0.40 1.14 85 270 33.0 0.24 1190
14 240 HB 0.5 5.0 0.18 0.40 0.95 80 220 33.0 0.21 1170
14 290 HB 0.5 4.0 0.16 0.35 0.76 40 150 22.5 0.23 1100
14 310 HB 0.5 4.0 0.16 0.35 0.76 35 140 22.5 0.23 990
12 200 HB 0.5 5.0 0.16 0.40 0.67 85 250 22.5 0.19 1190
13 42 HRc 0.5 4.0 0.16 0.40 0.67 60 190 22.2 0.19 1130
17,19 150 HB 0.5 5.0 0.13 0.50 1.43 60 250 33.0 0.29 1180
17,19 200 HB 0.5 5.0 0.13 0.50 1.24 60 230 33.0 0.29 1160
18,20 250 HB 0.5 5.0 0.13 0.50 1.14 60 190 33.0 0.29 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
CNMG 120408 NX – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.18 0.50 1.71 180 430 33.0 0.36 2265
2 190 HB 0.5 5.0 0.18 0.50 1.71 180 365 33.0 0.33 2240
3 250 HB 0.5 5.0 0.18 0.45 1.43 180 325 33.0 0.31 2220
6 180 HB 0.5 5.0 0.18 0.45 1.14 120 365 33.0 0.30 2220
4,6 230 HB 0.5 4.0 0.18 0.45 1.14 120 325 33.0 0.30 2200
5,7 280 HB 0.5 4.0 0.16 0.40 1.14 120 275 33.0 0.29 1165
8 350 HB 0.5 3.5 0.16 0.40 0.95 120 235 22.7 0.29 1145
10 220 HB 0.5 4.0 0.16 0.40 1.14 70 245 22.5 0.29 1155
10 280 HB 0.5 4.0 0.16 0.40 1.14 70 195 22.5 0.29 1130
11 320 HB 0.5 3.0 0.16 0.35 0.76 70 170 22.2 0.27 1110
11 350 HB 0.5 3.0 0.16 0.35 0.76 70 145 22.2 0.27 1100
15 150 HB 0.5 5.0 0.13 0.60 1.90 170 325 33.0 0.33 2220
15 200 HB 0.5 5.0 0.13 0.60 1.71 160 300 33.0 0.33 2200
16 250 HB 0.5 5.0 0.13 0.55 1.71 150 275 33.0 0.33 1175
17,19 150 HB 0.5 5.0 0.13 0.50 1.43 120 325 33.0 0.29 2200
17,19 200 HB 0.5 5.0 0.13 0.50 1.24 120 300 33.0 0.29 1175
18,20 250 HB 0.5 5.0 0.13 0.50 1.14 120 245 33.0 0.29 1155
38 45 HRc 0.5 2.5 0.10 0.30 0.57 50 130 22.0 0.24 990
38 50 HRc 0.5 2.0 0.10 0.25 0.38 40 115 11.5 0.19 775
38 55 HRc 0.5 1.5 0.10 0.20 0.29 40 105 11.0 0.17 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.10 0.25 0.38 40 80 11.5 0.17 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.20 0.29 30 65 11.0 0.14 445
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
Cast
Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
37
TURNINGMachining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.7 6.0 0.26 0.68 3.06 180 330 44.0 0.46 2240
2 190 HB 0.7 6.0 0.26 0.68 3.06 180 280 44.0 0.46 2220
3 250 HB 0.7 6.0 0.26 0.61 2.55 180 250 44.0 0.46 2200
6 180 HB 0.7 6.0 0.26 0.61 2.04 120 280 44.0 0.42 2200
4,6 230 HB 0.7 4.8 0.26 0.61 2.04 120 250 44.0 0.42 1180
5,7 280 HB 0.7 4.8 0.23 0.54 2.04 120 210 44.0 0.40 1150
8 350 HB 0.7 4.2 0.23 0.54 1.70 120 180 44.0 0.40 1130
10 220 HB 0.7 4.8 0.23 0.54 2.04 70 190 33.4 0.40 1140
10 280 HB 0.7 4.8 0.23 0.54 2.04 70 150 33.4 0.40 1120
11 320 HB 0.7 3.6 0.23 0.47 1.36 70 130 33.4 0.37 1100
11 350 HB 0.7 3.6 0.23 0.47 1.36 70 110 33.4 0.37 990
14 180 HB 0.7 6.0 0.25 0.54 2.04 170 270 44.0 0.40 1190
14 240 HB 0.7 6.0 0.25 0.54 1.70 160 220 44.0 0.38 1170
14 290 HB 0.7 4.8 0.23 0.47 1.36 80 150 33.4 0.32 1100
14 310 HB 0.7 4.8 0.23 0.47 1.36 70 140 33.4 0.32 990
12 200 HB 0.7 6.0 0.28 0.54 1.70 170 250 44.0 0.40 1190
13 42 HRc 0.7 4.8 0.28 0.54 1.70 120 190 33.0 0.35 1130
15 150 HB 0.7 6.0 0.20 0.81 3.40 170 250 44.0 0.46 2200
15 200 HB 0.7 6.0 0.20 0.81 3.06 160 230 44.0 0.46 1180
16 250 HB 0.7 6.0 0.20 0.74 3.06 150 210 44.0 0.46 1160
17,19 150 HB 0.7 6.0 0.20 0.68 2.55 120 250 44.0 0.40 1180
17,19 200 HB 0.7 6.0 0.20 0.68 2.21 120 230 44.0 0.40 1160
18,20 250 HB 0.7 6.0 0.20 0.68 2.04 120 190 44.0 0.40 1140
31,32 Incoloy 800 240 HB 0.7 3.6 0.25 0.47 1.19 25 45 22.7 0.37 332
33 Inconel 700 250 HB 0.7 3.6 0.25 0.47 1.19 25 45 22.7 0.37 330
34 Stellite 21 350 HB 0.7 3.6 0.25 0.47 1.19 23 40 22.7 0.37 228
36 TiAl6V4 - 0.7 4.8 0.25 0.54 1.36 45 65 22.7 0.44 555
37 T40 - 0.7 3.6 0.25 0.47 1.19 35 55 22.7 0.40 445
38 45 HRc 0.7 3.0 0.14 0.41 1.02 50 100 22.7 0.33 880
38 50 HRc 0.7 2.4 0.14 0.34 0.68 40 90 22.0 0.26 770
38 55 HRc 0.7 1.8 0.14 0.27 0.51 40 80 11.3 0.24 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.4 0.14 0.34 0.68 40 60 22.0 0.24 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.8 0.14 0.27 0.51 30 50 11.3 0.20 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.7 7.0 0.25 0.81 3.10 200 400 4.0 0.50 280
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
CNMG 120412 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
38
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.7 6.0 0.26 0.68 3.06 180 430 44.0 0.50 2265
2 190 HB 0.7 6.0 0.26 0.68 3.06 180 365 44.0 0.46 2240
3 250 HB 0.7 6.0 0.26 0.61 2.55 180 325 44.0 0.44 2220
6 180 HB 0.7 6.0 0.26 0.61 2.04 120 365 44.0 0.42 2220
4,6 230 HB 0.7 4.8 0.26 0.61 2.04 120 325 44.0 0.42 2200
5,7 280 HB 0.7 4.8 0.23 0.54 2.04 120 275 44.0 0.40 1165
8 350 HB 0.7 4.2 0.23 0.54 1.70 120 235 33.6 0.40 1145
10 220 HB 0.7 4.8 0.23 0.54 2.04 70 245 33.4 0.40 1155
10 280 HB 0.7 4.8 0.23 0.54 2.04 70 195 33.4 0.40 1130
11 320 HB 0.7 3.6 0.23 0.47 1.36 70 170 22.9 0.37 1110
11 350 HB 0.7 3.6 0.23 0.47 1.36 70 145 22.9 0.37 1100
15 150 HB 0.7 6.0 0.19 0.81 3.40 170 325 44.0 0.46 2220
15 200 HB 0.7 6.0 0.19 0.81 3.06 160 300 44.0 0.46 2200
16 250 HB 0.7 6.0 0.19 0.74 3.06 150 275 44.0 0.46 1175
17,19 150 HB 0.7 6.0 0.19 0.68 2.55 120 325 44.0 0.40 2200
17,19 200 HB 0.7 6.0 0.19 0.68 2.21 120 300 44.0 0.40 1175
18,20 250 HB 0.7 6.0 0.19 0.68 2.04 120 245 44.0 0.40 1155
38 45 HRc 0.7 3.0 0.14 0.41 1.02 50 130 22.7 0.33 990
38 50 HRc 0.7 2.4 0.14 0.34 0.68 40 115 22.0 0.26 775
38 55 HRc 0.7 1.8 0.14 0.27 0.51 40 105 11.3 0.24 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.4 0.14 0.34 0.68 40 80 22.0 0.24 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.8 0.14 0.27 0.51 30 65 11.3 0.20 445
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
Cast
Iron
CNMG 120412 NN – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.7 6.0 0.26 0.68 3.06 90 330 44.0 0.50 2240
2 190 HB 0.7 6.0 0.26 0.68 3.06 90 280 44.0 0.46 2220
3 250 HB 0.7 6.0 0.26 0.61 2.55 90 250 44.0 0.44 2200
6 180 HB 0.7 6.0 0.26 0.61 2.04 60 280 44.0 0.42 2200
4,6 230 HB 0.7 4.8 0.26 0.61 2.04 60 250 44.0 0.42 1180
5,7 280 HB 0.7 4.8 0.23 0.54 2.04 60 210 44.0 0.40 1150
8 350 HB 0.7 4.2 0.23 0.54 1.70 60 180 33.6 0.40 1130
10 220 HB 0.7 4.8 0.23 0.54 2.04 35 190 33.4 0.40 1140
10 280 HB 0.7 4.8 0.23 0.54 2.04 35 150 33.4 0.40 1120
11 320 HB 0.7 3.6 0.23 0.47 1.36 35 130 22.9 0.37 1100
11 350 HB 0.7 3.6 0.23 0.47 1.36 35 110 22.9 0.37 990
14 180 HB 0.7 6.0 0.25 0.54 2.04 85 270 44.0 0.33 1190
14 240 HB 0.7 6.0 0.25 0.54 1.70 80 220 44.0 0.29 1170
14 290 HB 0.7 4.8 0.23 0.47 1.36 40 150 33.4 0.32 1100
14 310 HB 0.7 4.8 0.23 0.47 1.36 35 140 33.4 0.32 990
12 200 HB 0.7 6.0 0.23 0.54 1.19 85 250 33.4 0.26 1190
13 42 HRc 0.7 4.8 0.23 0.54 1.19 60 190 22.9 0.26 1130
17,19 150 HB 0.7 6.0 0.19 0.68 2.55 60 250 44.0 0.40 1180
17,19 200 HB 0.7 6.0 0.19 0.68 2.21 60 230 44.0 0.40 1160
18,20 250 HB 0.7 6.0 0.19 0.68 2.04 60 190 44.0 0.40 1140
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Malleable & Nodular 8GGG40, GGG70,
50005
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
CNMG 120412 NN – LT 1005
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
39
TURNING
FProductivity
C N M M80° 0°
Shape Clearance Angle Toleranced ± 0.08m ± 0.13s ± 0.13
Ø d
l
m
Fixing,Chipbreaker
ss
Insert Designation s r Catalog Nr.l
T00041161.204.7612CNMM 120412 NR LT 1025
T00041150.804.7612CNMM 120408 NR LT 1025
F M R
LT 1025 Recommended for moderate to low speed
80° diamond shape, single sided inserts. Strong cutting edge for roughing operations which includes inter-rupted cut, high feed and high depth of cut.
Application Guide
CNMM
,
40
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.7 7.0 0.21 0.60 3.24 90 330 55.0 0.46 2240
2 190 HB 0.7 7.0 0.21 0.60 3.24 90 280 55.0 0.42 2220
3 250 HB 0.7 7.0 0.21 0.54 2.70 90 250 55.0 0.40 2200
6 180 HB 0.7 7.0 0.21 0.54 2.16 60 280 55.0 0.38 2200
4,6 230 HB 0.7 5.6 0.21 0.54 2.16 60 250 55.0 0.38 1180
5,7 280 HB 0.7 5.6 0.18 0.48 2.16 60 210 55.0 0.36 1150
8 350 HB 0.7 4.9 0.18 0.48 1.80 60 180 44.5 0.36 1130
10 220 HB 0.7 5.6 0.18 0.48 2.16 35 190 44.1 0.36 1140
10 280 HB 0.7 5.6 0.18 0.48 2.16 35 150 44.1 0.36 1120
11 320 HB 0.7 4.2 0.18 0.42 1.44 35 130 33.6 0.34 1100
11 350 HB 0.7 4.2 0.18 0.42 1.44 35 110 33.6 0.34 990
14 180 HB 0.7 7.0 0.20 0.48 2.16 85 270 55.0 0.30 1190
14 240 HB 0.7 7.0 0.20 0.48 1.80 80 220 55.0 0.26 1170
14 290 HB 0.7 5.6 0.18 0.42 1.44 40 150 44.1 0.29 1100
14 310 HB 0.7 5.6 0.18 0.42 1.44 35 140 44.1 0.29 990
12 200 HB 0.7 7.0 0.18 0.48 1.26 85 250 44.1 0.24 1190
13 42 HRc 0.7 5.6 0.18 0.48 1.26 60 190 33.6 0.24 1130
17,19 150 HB 0.7 7.0 0.15 0.60 2.70 60 250 55.0 0.36 1180
17,19 200 HB 0.7 7.0 0.15 0.60 2.34 60 230 55.0 0.36 1160
18,20 250 HB 0.7 7.0 0.15 0.60 2.16 60 190 55.0 0.36 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
CNMM 120412 NR – LT 1025
CNMM 120408 NR – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 7.0 0.21 0.60 2.88 90 330 44.2 0.46 2240
2 190 HB 0.5 7.0 0.21 0.60 2.88 90 280 44.2 0.42 2220
3 250 HB 0.5 7.0 0.21 0.54 2.40 90 250 44.2 0.40 2200
6 180 HB 0.5 7.0 0.21 0.54 1.92 60 280 44.2 0.38 2200
4,6 230 HB 0.5 5.6 0.21 0.54 1.92 60 250 44.2 0.38 1180
5,7 280 HB 0.5 5.6 0.18 0.48 1.92 60 210 44.2 0.36 1150
8 350 HB 0.5 4.9 0.18 0.48 1.60 60 180 33.8 0.36 1130
10 220 HB 0.5 5.6 0.18 0.48 1.92 35 190 33.5 0.36 1140
10 280 HB 0.5 5.6 0.18 0.48 1.92 35 150 33.5 0.36 1120
11 320 HB 0.5 4.2 0.18 0.42 1.28 35 130 33.1 0.34 1100
11 350 HB 0.5 4.2 0.18 0.42 1.28 35 110 33.1 0.34 990
14 180 HB 0.5 7.0 0.20 0.48 1.92 85 270 44.2 0.30 1190
14 240 HB 0.5 7.0 0.20 0.48 1.60 80 220 44.2 0.26 1170
14 290 HB 0.5 5.6 0.18 0.42 1.28 40 150 33.5 0.29 1100
14 310 HB 0.5 5.6 0.18 0.42 1.28 35 140 33.5 0.29 990
12 200 HB 0.5 7.0 0.18 0.48 1.12 85 250 33.5 0.24 1190
13 42 HRc 0.5 5.6 0.18 0.48 1.12 60 190 33.1 0.24 1130
17,19 150 HB 0.5 7.0 0.15 0.60 2.40 60 250 44.2 0.36 1180
17,19 200 HB 0.5 7.0 0.15 0.60 2.08 60 230 44.2 0.36 1160
18,20 250 HB 0.5 7.0 0.15 0.60 1.92 60 190 44.2 0.36 1140
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Malleable & Nodular 8GGG40, GGG70,
50005
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
41
TURNING
LT 1000
LT 1000
LT 1000 and 1025
NXCNMPTNMPWNMP
Stainless Steel
VC
Exotic Material
Cutting Conditions!Verify
NX-CNMP-TNMP-WNMP
Stainless SteelExotic Material
C N M P80° 0°
Shape Clearance Angle Toleranced ± 0.08m ± 0.13s ± 0.13
Ø d
l
m
Fixing,Chipbreaker
ss
Insert Designation s r Catalog Nr.l
T00019011.204.7612CNMP 120412 NN LT 1000
T00019000.804.7612CNMP 120408 NN LT 1000
F M R
LT 1000 Multi-MatTM General Usage – Premium
Insert Designation s r Catalog Nr.l
T00041181.204.7612CNMP 120412 NN LT 1025
T00041170.804.7612CNMP 120408 NN LT 1025
F M R
LT 1025 Recommended for moderate to low speed
80° diamond shape, double sided inserts with positive chipbreaker geometry. Generates low cutting force. Suitable for high temperature alloys.
Application Guide
Application guide
CNMP
42
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240
2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220
3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200
6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150
8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130
10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140
10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120
11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100
11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990
14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190
14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170
14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100
14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990
12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190
13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130
15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200
15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180
16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332
33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330
34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228
36 TiAl6V4 - 0.5 4.0 0.20 0.40 0.80 45 65 22.0 0.33 555
37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445
38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880
38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770
38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.25 0.40 40 60 11.5 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.20 0.30 30 50 11.0 0.15 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 3.0 0.40 280
Ste
el
Non-alloyed 1C35, Ck45, 1020,
1045, 1060, 28Mn6
Low alloyed 242CrMo4, St50,
Ck60, 4140, 4340, 100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Sta
inle
ss S
teel
Austenitic 4304, 316, X5CrNi18-
9
Duplex 5
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
X100CrMo13, 440C,
G-X260NiCr42
Har
dene
d M
at.
Steel
11
GGG40, GGG70, 50005
Hig
h Te
mp.
Allo
ys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cas
t Ir
on
CNMP 120408 NN – LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
43
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.7 6.0 0.26 0.68 3.06 180 330 44.0 0.46 2240
2 190 HB 0.7 6.0 0.26 0.68 3.06 180 280 44.0 0.46 2220
3 250 HB 0.7 6.0 0.26 0.61 2.55 180 250 44.0 0.46 2200
6 180 HB 0.7 6.0 0.26 0.61 2.04 120 280 44.0 0.42 2200
4,6 230 HB 0.7 4.8 0.26 0.61 2.04 120 250 44.0 0.42 1180
5,7 280 HB 0.7 4.8 0.23 0.54 2.04 120 210 44.0 0.40 1150
8 350 HB 0.7 4.2 0.23 0.54 1.70 120 180 44.0 0.40 1130
10 220 HB 0.7 4.8 0.23 0.54 2.04 70 190 33.4 0.40 1140
10 280 HB 0.7 4.8 0.23 0.54 2.04 70 150 33.4 0.40 1120
11 320 HB 0.7 3.6 0.23 0.47 1.36 70 130 33.4 0.37 1100
11 350 HB 0.7 3.6 0.23 0.47 1.36 70 110 33.4 0.37 990
14 180 HB 0.7 6.0 0.25 0.54 2.04 170 270 44.0 0.40 1190
14 240 HB 0.7 6.0 0.25 0.54 1.70 160 220 44.0 0.38 1170
14 290 HB 0.7 4.8 0.23 0.47 1.36 80 150 33.4 0.32 1100
14 310 HB 0.7 4.8 0.23 0.47 1.36 70 140 33.4 0.32 990
12 200 HB 0.7 6.0 0.28 0.54 1.70 170 250 44.0 0.40 1190
13 42 HRc 0.7 4.8 0.28 0.54 1.70 120 190 33.0 0.36 1130
15 150 HB 0.7 6.0 0.20 0.81 3.40 170 250 44.0 0.46 2200
15 200 HB 0.7 6.0 0.20 0.81 3.06 160 230 44.0 0.46 1180
16 250 HB 0.7 6.0 0.20 0.74 3.06 150 210 44.0 0.46 1160
17,19 150 HB 0.7 6.0 0.20 0.68 2.55 120 250 44.0 0.40 1180
17,19 200 HB 0.7 6.0 0.20 0.68 2.21 120 230 44.0 0.40 1160
18,20 250 HB 0.7 6.0 0.20 0.68 2.04 120 190 44.0 0.40 1140
31,32 Incoloy 800 240 HB 0.7 3.6 0.25 0.47 1.19 25 45 22.7 0.37 332
33 Inconel 700 250 HB 0.7 3.6 0.25 0.47 1.19 25 45 22.7 0.37 330
34 Stellite 21 350 HB 0.7 3.6 0.25 0.47 1.19 23 40 22.7 0.37 228
36 TiAl6V4 - 0.7 4.8 0.25 0.54 1.36 45 65 22.7 0.40 555
37 T40 - 0.7 3.6 0.25 0.47 1.19 35 55 22.7 0.37 445
38 45 HRc 0.7 3.0 0.14 0.41 1.02 50 100 22.7 0.33 880
38 50 HRc 0.7 2.4 0.14 0.34 0.68 40 90 22.0 0.26 770
38 55 HRc 0.7 1.8 0.14 0.27 0.51 40 80 11.3 0.24 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.4 0.14 0.34 0.68 40 60 22.0 0.24 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.8 0.14 0.27 0.51 30 50 11.3 0.20 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.7 7.0 0.25 0.81 3.10 200 400 4.0 0.50 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
CNMP 120412 NN – LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
44
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.7 6.0 0.26 0.68 3.06 90 330 44.0 0.50 2240
2 190 HB 0.7 6.0 0.26 0.68 3.06 90 280 44.0 0.46 2220
3 250 HB 0.7 6.0 0.26 0.61 2.55 90 250 44.0 0.44 2200
6 180 HB 0.7 6.0 0.26 0.61 2.04 60 280 44.0 0.42 2200
4,6 230 HB 0.7 4.8 0.26 0.61 2.04 60 250 44.0 0.42 1180
5,7 280 HB 0.7 4.8 0.23 0.54 2.04 60 210 44.0 0.40 1150
8 350 HB 0.7 4.2 0.23 0.54 1.70 60 180 33.6 0.40 1130
10 220 HB 0.7 4.8 0.23 0.54 2.04 35 190 33.4 0.40 1140
10 280 HB 0.7 4.8 0.23 0.54 2.04 35 150 33.4 0.40 1120
11 320 HB 0.7 3.6 0.23 0.47 1.36 35 130 22.9 0.37 1100
11 350 HB 0.7 3.6 0.23 0.47 1.36 35 110 22.9 0.37 990
14 180 HB 0.7 6.0 0.25 0.54 2.04 85 270 44.0 0.33 1190
14 240 HB 0.7 6.0 0.25 0.54 1.70 80 220 44.0 0.29 1170
14 290 HB 0.7 4.8 0.23 0.47 1.36 40 150 33.4 0.32 1100
14 310 HB 0.7 4.8 0.23 0.47 1.36 35 140 33.4 0.32 990
12 200 HB 0.7 6.0 0.23 0.54 1.19 85 250 33.4 0.26 1190
13 42 HRc 0.7 4.8 0.23 0.54 1.19 60 190 22.9 0.26 1130
17,19 150 HB 0.7 6.0 0.19 0.68 2.55 60 250 44.0 0.40 1180
17,19 200 HB 0.7 6.0 0.19 0.68 2.21 60 230 44.0 0.40 1160
18,20 250 HB 0.7 6.0 0.19 0.68 2.04 60 190 44.0 0.40 1140
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Malleable & Nodular 8GGG40, GGG70,
50005
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
CNMP 120408 NN – LT 1025
CNMP 120412 NN – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.50 1.80 90 330 33.0 0.38 2240
2 190 HB 0.5 5.0 0.21 0.50 1.80 90 280 33.0 0.35 2220
3 250 HB 0.5 5.0 0.21 0.45 1.50 90 250 33.0 0.33 2200
6 180 HB 0.5 5.0 0.21 0.45 1.20 60 280 33.0 0.32 2200
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 60 250 33.0 0.32 1180
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 60 210 33.0 0.30 1150
8 350 HB 0.5 3.5 0.18 0.40 1.00 60 180 22.7 0.30 1130
10 220 HB 0.5 4.0 0.18 0.40 1.20 35 190 22.5 0.30 1140
10 280 HB 0.5 4.0 0.18 0.40 1.20 35 150 22.5 0.30 1120
11 320 HB 0.5 3.0 0.18 0.35 0.80 35 130 22.2 0.28 1100
11 350 HB 0.5 3.0 0.18 0.35 0.80 35 110 22.2 0.28 990
14 180 HB 0.5 5.0 0.20 0.40 1.20 85 270 33.0 0.25 1190
14 240 HB 0.5 5.0 0.20 0.40 1.00 80 220 33.0 0.22 1170
14 290 HB 0.5 4.0 0.18 0.35 0.80 40 150 22.5 0.24 1100
14 310 HB 0.5 4.0 0.18 0.35 0.80 35 140 22.5 0.24 990
12 200 HB 0.5 5.0 0.18 0.40 0.70 85 250 22.5 0.20 1190
13 42 HRc 0.5 4.0 0.18 0.40 0.70 60 190 22.2 0.20 1130
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 60 250 33.0 0.30 1180
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 60 230 33.0 0.30 1160
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 60 190 33.0 0.30 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
45
TURNING
FProductivity
Stainless Steel
VC
C P M T80° 11°
Shape Clearance Anglel
m
Tolerance
Ø d
s ± 0.13For l = 06/09, d ± 0.05 m ± 0.08 For l = 12, d ± 0.08 m ± 0.13
Fixing, Chipbreaker
s
F M RInsert Designation s r Catalog Nr.l
LT 1000 Multi-MatTM General Usage – Premium
T00031460.803.979CPMT 09T308 NN LT 1000
T00030880.402.386CPMT 060204 NN LT 1000
T00031450.403.979CPMT 09T304 NN LT 1000
T00031440.802.386CPMT 060208 NN LT 1000
Application Guide
80° diamond shape inserts with positive chipbreaker geometry. Very popular and useful for boring (even of small diameters), facing and external turning operations.
CPMT
46
TURNING Machining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.4 2.1 0.08 0.20 0.37 180 330 11.0 0.16 2240
2 190 HB 0.4 1.8 0.08 0.19 0.32 180 280 11.0 0.16 2220
3 250 HB 0.4 1.8 0.08 0.17 0.30 180 250 11.0 0.16 2200
6 180 HB 0.4 1.8 0.08 0.17 0.31 120 280 11.0 0.14 2200
4,6 230 HB 0.4 1.8 0.08 0.17 0.30 120 250 11.0 0.14 1180
5,7 280 HB 0.4 1.4 0.08 0.15 0.25 120 210 11.0 0.14 1150
8 350 HB 0.4 1.4 0.08 0.15 0.22 120 180 11.0 0.14 1130
10 220 HB 0.4 1.8 0.07 0.15 0.25 70 190 11.0 0.11 1140
10 280 HB 0.4 1.8 0.07 0.14 0.25 70 150 11.0 0.11 1120
11 320 HB 0.4 1.4 0.07 0.12 0.20 70 130 11.0 0.11 1100
11 350 HB 0.4 1.4 0.07 0.12 0.16 70 110 11.0 0.11 990
14 180 HB 0.4 1.8 0.08 0.15 0.20 170 270 11.0 0.11 2220
14 240 HB 0.4 1.8 0.08 0.15 0.16 160 220 11.0 0.11 1190
14 290 HB 0.4 1.4 0.07 0.12 0.12 80 150 11.0 0.11 1100
14 310 HB 0.4 1.4 0.07 0.12 0.12 70 140 11.0 0.11 990
12 200 HB 0.4 1.8 0.08 0.15 0.20 170 250 00.9 0.14 2210
13 42 HRc 0.4 1.4 0.08 0.14 0.16 120 190 00.9 0.11 1140
15 150 HB 0.4 2.1 0.06 0.17 0.40 170 250 11.0 0.16 2200
15 200 HB 0.4 2.1 0.06 0.17 0.37 160 230 11.0 0.16 1180
16 250 HB 0.4 2.1 0.06 0.17 0.37 150 210 11.0 0.16 1160
17,19 150 HB 0.4 1.8 0.06 0.15 0.30 120 250 11.0 0.14 1180
17,19 200 HB 0.4 1.8 0.06 0.15 0.25 120 230 11.0 0.14 1160
18,20 250 HB 0.4 1.8 0.06 0.15 0.25 120 190 11.0 0.14 1140
31,32 Incoloy 800 240 HB 0.4 1.4 0.08 0.13 0.16 25 45 11.0 0.11 333
33 Inconel 700 250 HB 0.4 1.4 0.08 0.13 0.16 25 45 11.0 0.11 330
34 Stellite 21 350 HB 0.4 1.4 0.08 0.13 0.16 23 40 11.0 0.11 228
36 TiAl6V4 - 0.4 1.4 0.08 0.14 0.20 45 65 11.0 0.13 555
37 T40 - 0.4 1.4 0.08 0.12 0.16 35 55 11.0 0.11 445
38 45 HRc 0.4 1.3 0.04 0.10 0.12 50 100 00.8 0.10 880
38 50 HRc 0.4 1.1 0.04 0.09 0.11 40 90 00.6 0.08 770
38 55 HRc 0.4 1.0 0.04 0.08 0.08 40 80 00.5 0.06 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.4 1.1 0.04 0.10 0.11 40 60 00.6 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.4 1.0 0.04 0.08 0.08 30 50 00.5 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.4 2.8 0.08 0.26 0.43 200 400 1.0 0.18 280
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
CPMT 060204 NN – LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
47
TURNINGMachining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.2 3.0 0.11 0.23 0.60 180 330 11.6 0.18 2240
2 190 HB 0.2 2.5 0.11 0.22 0.52 180 280 11.6 0.18 2220
3 250 HB 0.2 2.5 0.11 0.20 0.48 180 250 11.6 0.18 2200
6 180 HB 0.2 2.5 0.11 0.20 0.50 120 280 11.6 0.15 2200
4,6 230 HB 0.2 2.5 0.11 0.20 0.48 120 250 11.6 0.15 1180
5,7 280 HB 0.2 2.0 0.11 0.18 0.40 120 210 11.6 0.15 1150
8 350 HB 0.2 2.0 0.11 0.18 0.35 120 180 11.6 0.15 1130
10 220 HB 0.2 2.5 0.10 0.18 0.40 70 190 11.6 0.12 1140
10 280 HB 0.2 2.5 0.10 0.16 0.40 70 150 11.6 0.12 1120
11 320 HB 0.2 2.0 0.10 0.14 0.32 70 130 11.6 0.12 1100
11 350 HB 0.2 2.0 0.10 0.14 0.26 70 110 11.6 0.12 990
14 180 HB 0.2 2.5 0.11 0.18 0.32 170 270 11.6 0.12 2220
14 240 HB 0.2 2.5 0.11 0.18 0.26 160 220 11.6 0.12 1190
14 290 HB 0.2 2.0 0.10 0.14 0.19 80 150 11.6 0.12 1100
14 310 HB 0.2 2.0 0.10 0.14 0.19 70 140 11.6 0.12 990
12 200 HB 0.2 2.5 0.11 0.18 0.32 170 250 11.4 0.15 2210
13 42 HRc 0.2 2.0 0.11 0.16 0.26 120 190 11.4 0.12 1140
15 150 HB 0.2 3.0 0.08 0.20 0.64 170 250 11.6 0.18 2200
15 200 HB 0.2 3.0 0.08 0.20 0.60 160 230 11.6 0.18 1180
16 250 HB 0.2 3.0 0.08 0.20 0.60 150 210 11.6 0.18 1160
17,19 150 HB 0.2 2.5 0.08 0.18 0.48 120 250 11.6 0.15 1180
17,19 200 HB 0.2 2.5 0.08 0.18 0.40 120 230 11.6 0.15 1160
18,20 250 HB 0.2 2.5 0.08 0.18 0.40 120 190 11.6 0.15 1140
31,32 Incoloy 800 240 HB 0.2 2.0 0.11 0.15 0.26 25 45 11.6 0.12 333
33 Inconel 700 250 HB 0.2 2.0 0.11 0.15 0.26 25 45 11.6 0.12 330
34 Stellite 21 350 HB 0.2 2.0 0.11 0.15 0.26 23 40 11.6 0.12 228
36 TiAl6V4 - 0.2 2.0 0.11 0.16 0.32 45 65 11.6 0.14 555
37 T40 - 0.2 2.0 0.11 0.14 0.26 35 55 11.6 0.12 445
38 45 HRc 0.2 1.8 0.06 0.12 0.19 50 100 11.3 0.11 880
38 50 HRc 0.2 1.6 0.06 0.11 0.18 40 90 11.0 0.09 770
38 55 HRc 0.2 1.4 0.06 0.09 0.13 40 80 00.8 0.07 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.2 1.6 0.06 0.12 0.18 40 60 11.0 0.11 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.2 1.4 0.06 0.09 0.13 30 50 00.8 0.07 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.2 3.9 0.11 0.30 0.69 200 400 1.6 0.20 280
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
CPMT 09T304 NN – LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
48
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 4.0 0.21 0.50 1.62 180 330 33.0 0.34 2240
2 190 HB 0.5 4.0 0.21 0.50 1.62 180 280 33.0 0.32 2220
3 250 HB 0.5 4.0 0.21 0.45 1.35 180 250 33.0 0.30 2200
6 180 HB 0.5 4.0 0.21 0.45 1.08 120 280 33.0 0.29 2200
4,6 230 HB 0.5 3.2 0.21 0.45 1.08 120 250 33.0 0.29 1180
5,7 280 HB 0.5 3.2 0.18 0.40 1.08 120 210 33.0 0.27 1150
8 350 HB 0.5 2.8 0.18 0.40 0.90 120 180 22.7 0.27 1130
10 220 HB 0.5 3.2 0.18 0.40 1.08 70 190 22.5 0.27 1140
10 280 HB 0.5 3.2 0.18 0.40 1.08 70 150 22.5 0.27 1120
11 320 HB 0.5 2.4 0.18 0.35 0.72 70 130 22.2 0.25 1100
11 350 HB 0.5 2.4 0.18 0.35 0.72 70 110 22.2 0.25 990
14 180 HB 0.5 4.0 0.20 0.40 1.08 170 270 33.0 0.23 1190
14 240 HB 0.5 4.0 0.20 0.40 0.90 160 220 33.0 0.20 1170
14 290 HB 0.5 3.2 0.18 0.35 0.72 80 150 22.5 0.22 1100
14 310 HB 0.5 3.2 0.18 0.35 0.72 70 140 22.5 0.22 990
12 200 HB 0.5 4.0 0.18 0.40 0.63 170 250 22.5 0.18 1190
13 42 HRc 0.5 3.2 0.18 0.40 0.63 120 190 22.2 0.18 1130
15 150 HB 0.5 4.0 0.15 0.60 1.80 170 250 33.0 0.32 2200
15 200 HB 0.5 4.0 0.15 0.60 1.62 160 230 33.0 0.32 1180
16 250 HB 0.5 4.0 0.15 0.55 1.62 150 210 33.0 0.32 1160
17,19 150 HB 0.5 4.0 0.15 0.50 1.35 120 250 33.0 0.27 1180
17,19 200 HB 0.5 4.0 0.15 0.50 1.17 120 230 33.0 0.27 1160
18,20 250 HB 0.5 4.0 0.15 0.50 1.08 120 190 33.0 0.27 1140
31,32 Incoloy 800 240 HB 0.5 2.4 0.20 0.35 0.63 25 45 22.0 0.25 332
33 Inconel 700 250 HB 0.5 2.4 0.20 0.35 0.63 25 45 22.0 0.25 330
34 Stellite 21 350 HB 0.5 2.4 0.20 0.35 0.63 23 40 22.0 0.25 228
36 TiAl6V4 - 0.5 2.8 0.20 0.40 0.72 45 65 22.0 0.30 555
37 T40 - 0.5 2.4 0.20 0.35 0.63 35 55 22.0 0.27 445
38 45 HRc 0.5 2.0 0.11 0.30 0.54 50 100 22.0 0.23 880
38 50 HRc 0.5 1.6 0.11 0.25 0.36 40 90 11.5 0.18 770
38 55 HRc 0.5 1.2 0.11 0.20 0.27 40 80 11.0 0.16 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.6 0.11 0.25 0.36 40 60 11.5 0.16 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.2 0.11 0.20 0.27 30 50 11.0 0.14 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.8 0.20 0.60 1.62 200 400 3.0 0.36 280
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
CPMT 09T308 NN – LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
49
TURNING
LT 10 and LT 1000
LT 10 and LT 1000
FProductivity
Stainless Steel
VC
D C M T7°
Shape Clearance Angle
55°
Toleranced ± 0.05m ± 0.08s ± 0.13
l
mØ d
Fixing, Chipbreaker
s
F M R
Application Guide
Insert Designation s r Catalog Nr.l
LT 10 Multi-MatTM General Usage – Standard
T00007210.803.9711DCMT 11T308 NN LT 10
T00000650.403.9711DCMT 11T304 NN LT 10
T00000640.402.387DCMT 070204 NN LT 10
F M
Application Guide
Insert Designation s r Catalog Nr.l
T00019040.803.9711DCMT 11T308 NN LT 1000
T00019030.403.9711DCMT 11T304 NN LT 1000
T00019020.402.387DCMT 070204 NN LT 1000
LT 1000 Multi-MatTM General Usage – Premium
55° diamond shape inserts. Suitable for internal turning due to a unique chip removal geometry. Generates low cutting force. Most suitable for small work-pieces.
R
DCMT
50
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.3 2.1 0.08 0.20 0.37 180 330 11.0 0.14 3300
2 190 HB 0.3 1.8 0.08 0.19 0.32 180 280 11.0 0.14 2260
3 250 HB 0.3 1.8 0.08 0.17 0.30 180 250 11.0 0.14 2240
6 180 HB 0.3 1.8 0.08 0.17 0.31 120 280 11.0 0.11 2260
4,6 230 HB 0.3 1.8 0.08 0.17 0.30 120 250 11.0 0.11 2240
5,7 280 HB 0.3 1.4 0.08 0.15 0.25 120 210 11.0 0.10 2200
8 350 HB 0.3 1.4 0.08 0.15 0.22 120 180 11.0 0.10 1180
10 220 HB 0.3 1.8 0.07 0.15 0.25 70 190 00.9 0.08 1180
10 280 HB 0.3 1.8 0.07 0.14 0.25 70 150 00.9 0.08 1140
11 320 HB 0.3 1.4 0.07 0.12 0.20 70 130 00.9 0.08 1120
11 350 HB 0.3 1.4 0.07 0.12 0.16 70 110 00.9 0.08 1110
14 180 HB 0.3 1.8 0.06 0.15 0.20 170 270 11.0 0.07 2260
14 240 HB 0.3 1.8 0.06 0.15 0.16 160 220 11.0 0.06 2210
14 290 HB 0.3 1.4 0.06 0.12 0.12 80 150 00.9 0.06 1140
14 310 HB 0.3 1.4 0.06 0.12 0.12 70 140 00.9 0.06 1140
12 200 HB 0.3 1.8 0.06 0.15 0.20 170 250 00.9 0.07 2240
13 42 HRc 0.3 1.4 0.06 0.14 0.16 120 190 00.8 0.06 1180
15 150 HB 0.3 2.1 0.06 0.17 0.40 170 250 11.0 0.14 2240
15 200 HB 0.3 2.1 0.06 0.17 0.37 160 230 11.0 0.14 2220
16 250 HB 0.3 2.1 0.06 0.17 0.37 150 210 11.0 0.14 2200
17,19 150 HB 0.3 1.8 0.06 0.15 0.30 120 250 11.0 0.10 2240
17,19 200 HB 0.3 1.8 0.06 0.15 0.25 120 230 11.0 0.10 2220
18,20 250 HB 0.3 1.8 0.06 0.15 0.25 120 190 11.0 0.10 1180
31,32 Incoloy 800 240 HB 0.3 1.4 0.07 0.13 0.16 25 50 00.7 0.08 440
33 Inconel 700 250 HB 0.3 1.4 0.07 0.13 0.16 25 50 00.7 0.08 440
34 Stellite 21 350 HB 0.3 1.4 0.07 0.13 0.16 23 45 00.7 0.08 335
36 TiAl6V4 - 0.3 1.4 0.07 0.14 0.20 45 65 00.7 0.11 660
37 T40 - 0.3 1.4 0.07 0.12 0.16 35 60 00.7 0.08 550
38 45 HRc 0.3 1.3 0.04 0.10 0.12 50 100 00.7 0.08 990
38 50 HRc 0.3 1.1 0.04 0.09 0.11 40 90 00.6 0.06 880
38 55 HRc 0.0 1.0 0.04 0.08 0.08 40 80 00.5 0.05 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.1 0.04 0.10 0.11 40 60 00.6 0.08 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.0 0.04 0.08 0.08 30 50 00.5 0.05 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 2.8 0.08 0.26 0.43 200 400 1.0 0.18 350
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
7 GG20, GG40, EN-GJL-250,
No30B
8
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
DCMT 070204 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
51
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300
2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260
3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240
6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260
4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240
5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200
8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180
10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180
10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140
11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120
11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110
14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260
14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210
14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140
14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140
12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240
13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180
15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240
15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220
16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200
17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240
17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220
18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335
36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660
37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550
38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990
38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880
38 55 HRc 0.0 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 00.9 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
DCMT 11T304 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
52
TURNING Machining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 4.0 0.21 0.50 1.62 180 330 33.0 0.32 2240
2 190 HB 0.5 4.0 0.21 0.50 1.62 180 280 33.0 0.32 2220
3 250 HB 0.5 4.0 0.21 0.45 1.35 180 250 33.0 0.32 2200
6 180 HB 0.5 4.0 0.21 0.45 1.08 120 280 33.0 0.29 2200
4,6 230 HB 0.5 3.2 0.21 0.45 1.08 120 250 33.0 0.29 1180
5,7 280 HB 0.5 3.2 0.18 0.40 1.08 120 210 33.0 0.27 1150
8 350 HB 0.5 2.8 0.18 0.40 0.90 120 180 33.0 0.27 1130
10 220 HB 0.5 3.2 0.18 0.40 1.08 70 190 22.5 0.27 1140
10 280 HB 0.5 3.2 0.18 0.40 1.08 70 150 22.5 0.27 1120
11 320 HB 0.5 2.4 0.18 0.35 0.72 70 130 22.5 0.25 1100
11 350 HB 0.5 2.4 0.18 0.35 0.72 70 110 22.5 0.25 990
14 180 HB 0.5 4.0 0.20 0.40 1.08 170 270 33.0 0.32 1190
14 240 HB 0.5 4.0 0.20 0.40 0.90 160 220 33.0 0.29 1170
14 290 HB 0.5 3.2 0.18 0.35 0.72 80 150 22.5 0.25 1100
14 310 HB 0.5 3.2 0.18 0.35 0.72 70 140 22.5 0.25 990
12 200 HB 0.5 4.0 0.22 0.40 0.90 170 250 33.0 0.29 1190
13 42 HRc 0.5 3.2 0.22 0.40 0.90 120 190 22.5 0.29 1130
15 150 HB 0.5 4.0 0.15 0.60 1.80 170 250 33.0 0.32 2200
15 200 HB 0.5 4.0 0.15 0.60 1.62 160 230 33.0 0.32 1180
16 250 HB 0.5 4.0 0.15 0.55 1.62 150 210 33.0 0.32 1160
17,19 150 HB 0.5 4.0 0.15 0.50 1.35 120 250 33.0 0.27 1180
17,19 200 HB 0.5 4.0 0.15 0.50 1.17 120 230 33.0 0.27 1160
18,20 250 HB 0.5 4.0 0.15 0.50 1.08 120 190 33.0 0.27 1140
31,32 Incoloy 800 240 HB 0.5 2.4 0.20 0.35 0.63 25 45 22.0 0.25 332
33 Inconel 700 250 HB 0.5 2.4 0.20 0.35 0.63 25 45 22.0 0.25 330
34 Stellite 21 350 HB 0.5 2.4 0.20 0.35 0.63 23 40 22.0 0.25 228
36 TiAl6V4 - 0.5 3.2 0.20 0.40 0.72 45 65 22.0 0.30 555
37 T40 - 0.5 2.4 0.20 0.35 0.63 35 55 22.0 0.27 445
38 45 HRc 0.5 2.0 0.11 0.30 0.54 50 100 22.0 0.23 880
38 50 HRc 0.5 1.6 0.11 0.25 0.36 40 90 11.5 0.18 770
38 55 HRc 0.5 1.2 0.11 0.20 0.27 40 80 11.0 0.16 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.6 0.11 0.25 0.36 40 60 11.5 0.16 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.2 0.11 0.20 0.27 30 50 11.0 0.14 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.8 0.20 0.60 1.60 200 400 3.0 0.36 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
7 GG20, GG40, EN-GJL-250,
No30B
10
8
6 410, X6Cr17, 17-4 PH, 430
4304, 316,
X5CrNi18-9
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
Suggested Starting Parameters
1C35, Ck45, 1020, 1045, 1060, 28Mn6
Amax [mm²]
D.O.C. [mm]VDI Group
Material Examples* HardnessFeed [mm/rev] Vc [m/min]
Gr. N°
DCMT 11T308 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
53
TURNING
VC
Productivity
F M RInsert Designation s r Catalog Nr.l
LT 1005 Recommended for moderate to high speed
T00032421.206.3515DNMA 150612 LT 1005
T00032410.806.3515DNMA 150608 LT 1005
Application Guide
55° diamond shape flat inserts. Strong edge preparation, mainly for gray cast iron machining. Suitable for profiling of complex shapes, from roughing to finishing.
Fixing,Chipbreaker
D N M0°
Shape Clearance Angle Tolerance
55°
l
mØ d
s ± 0.13For l = 11, d ± 0.05 m ± 0.08 For l = 15, d ± 0.08 m ± 0.13
s
DNMA
54
TURNING Machining Conditions
DNMA 150608 – LT 1005
DNMA 150612 – LT 1005
min max min max min max D.O.C. Feed
15 150 HB 0.7 5.0 0.15 0.46 1.3 270 450 33.5 00.33 3350
15 200 HB 0.7 5.0 0.15 0.42 1.2 200 320 33.5 00.33 2250
16 250 HB 0.7 5.0 0.15 0.38 1.2 170 240 33.5 00.33 2220
17,19 150 HB 0.7 5.0 0.15 0.46 1.0 130 260 22.5 00.30 2240
17,19 200 HB 0.7 5.0 0.15 0.42 0.9 130 230 22.5 00.30 2210
18,20 250 HB 0.7 5.0 0.15 0.38 0.8 130 190 22.5 00.30 1180
CChilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.0 0.11 0.24 0.3 40 60 11.4 00.16 550
WWhite Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.5 0.11 0.24 0.2 30 50 11.0 00.15 440
HH 11
GGG40, GGG70, 50005
CCast
Iron
GGrey 7 GG20, GG40, EN-GJL-250,
No30B
MMalleable & Nodular 8
mmin mmax mmin mmax mmin mmax DD.O.C. FFeed VVcc
15 150 HB 0.7 5.0 0.15 0.42 1.3 270 450 33.2 00.30 3350
15 200 HB 0.7 5.0 0.15 0.40 1.2 200 320 33.2 00.30 2250
16 250 HB 0.7 5.0 0.15 0.36 1.2 170 240 33.2 00.30 2220
17,19 150 HB 0.7 5.0 0.15 0.42 1.0 130 260 22.5 00.28 2240
17,19 200 HB 0.7 5.0 0.15 0.40 0.8 130 230 22.5 00.28 2210
18,20 250 HB 0.7 5.0 0.15 0.36 0.8 130 190 22.5 00.28 1180
CChilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.0 0.11 0.22 0.2 40 60 11.4 00.15 550
WWhite Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.5 0.11 0.22 0.2 30 50 11.0 00.15 440
HH 11
GGG40, GGG70, 50005
CCast
Iron
SSuggested Starting Parameters
FFeed [mm/rev] VVc [m/min]AAmax [mm²]
DD.O.C. [mm]MMaterial Group GGr. N°
VVDI Group
MMaterial Examples* HHardness
GGrey 7 GG20, GG40, EN-GJL-250,
No30B
MMalleable & Nodular 8
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm]Feed
[mm/rev] Amax[mm2]
Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm]Feed
[mm/rev] Amax[mm2]
Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Cast
Iron
Grey
Malleable & Nodular
H
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Cast
Iron
Grey
Malleable & Nodular
H
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Cast
Iron
Grey
Malleable & Nodular
H
Chilled Cast Iron
White Cast Iron
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
55
TURNING
F M RInsert Designation s r Catalog Nr.l
LT 10 Multi-MatTM General Usage – Standard
T00006721.206.3515DNMG 150612 NN LT 10
T00000670.806.3515DNMG 150608 NN LT 10
T00005830.406.3515DNMG 150604 NN LT 10
T00010211.204.7615DNMG 150412 NN LT 10
T00004750.804.7615DNMG 150408 NN LT 10
T00004760.404.7615DNMG 150404 NN LT 10
T00006750.804.7611DNMG 110408 NN LT 10
T00000660.404.7611DNMG 110404 NN LT 10
D N M G0°
Shape Clearance Angle Tolerance Fixing, Chipbreaker
55°
l
mØ d
s
s ± 0.13For l = 11, d ± 0.05 m ± 0.08 For l = 15, d ± 0.08 m ± 0.13
F M RInsert Designation s r Catalog Nr.l
LT 1000 Multi-MatTM General Usage – Premium
T00030970.804.7615DNMG 150408 NX LT 1000
T00032200.806.3515DNMG 150608 NX LT 1000
T00019110.806.3515DNMG 150608 NN LT 1000
T00019100.406.3515DNMG 150604 NN LT 1000
T00019091.204.7615DNMG 150412 NN LT 1000
T00019080.804.7615DNMG 150408 NN LT 1000
T00019070.404.7615DNMG 150404 NN LT 1000
T00019060.804.7611DNMG 110408 NN LT 1000
T00019050.404.7611DNMG 110404 NN LT 1000
T00019121.206.3515DNMG 150612 NN LT 1000
LT 10 and LT 1000
NX LT 10 and LT 1000 NX LT 10 and LT 1000
LT 10 and LT 1000
NX-CNMP-TNMP-WNMP
Stainless SteelExotic Material Exotic Material
Cutting Conditions!Verify
FProductivity
Stainless Steel
VC
Application Guide
Application Guide
DNMG
55°
56
TURNING
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
F M RInsert Designation s r Catalog Nr.l
LT 1025 Recommended for moderate to low speed
T00041271.206.3515DNMG 150612 NN LT 1025
T0004123
T0004126
0.80
0.80
6.35
6.35
15
15
DNMG 150608 NX LT 1025
DNMG 150608 NN LT 1025
T0004124
T0004122
1.20
1.20
4.76
4.76
15
15
DNMG 150412 NN LT 1025
DNMG 150408 NX LT 1025
T00041210.804.7615DNMG 150408 NN LT 1025
T00041190.804.7611DNMG 110408 NN LT 1025
Application Guide
NX for LT 1025 LT 1005
NX-CNMP-TNMP-WNMP
Stainless SteelExotic Material VC
Productivity
D N M G
55° diamond shape inserts. Suitable for profiling of complex shapes, from roughing to finishing.
F M RInsert Designation s r Catalog Nr.l
LT 1005 Recommended for moderate to high speed
T00040681.206.3515DNMG 150612 NN LT 1005
T0004063
T0004067
0.80
0.80
6.35
6.35
15
15
DNMG 150608 NX LT 1005
DNMG 150608 NN LT 1005
T0004064
T0004062
1.20
1.20
4.76
4.76
15
15
DNMG 150412 NN LT 1005
DNMG 150408 NX LT 1005
T00040610.804.7615DNMG 150408 NN LT 1005
T00040590.804.7611DNMG 110408 NN LT 1005
Application Guide
NX chipbreaker NN chipbreaker
57
TURNINGMachining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300
2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260
3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240
6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260
4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240
5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200
8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180
10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180
10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140
11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120
11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110
14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260
14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210
14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140
14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140
12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240
13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180
15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240
15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220
16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200
17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240
17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220
18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335
36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660
37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550
38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990
38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880
38 55 HRc 0.0 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 00.9 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
DNMG 110404 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
58
TURNING Machining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240
2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220
3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200
6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150
8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130
10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140
10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120
11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100
11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990
14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190
14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170
14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100
14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990
12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190
13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130
15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200
15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180
16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332
33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330
34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228
36 TiAl6V4 - 0.5 3.5 0.20 0.40 0.80 45 65 22.0 0.33 555
37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445
38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880
38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770
38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.25 0.40 40 60 11.5 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.20 0.30 30 50 11.0 0.15 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 3.0 0.40 280
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
10
8
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
Suggested Starting Parameters
1C35, Ck45, 1020, 1045, 1060, 28Mn6
Amax [mm²]
D.O.C. [mm]VDI Group
Material Examples* HardnessFeed [mm/rev] Vc [m/min]
St
eel
Non-alloyed
Low alloyed
Material Group Gr. N°
DNMG 110408 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
59
TURNINGMachining Conditions
DNMG 110408 NN – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.50 1.80 90 330 33.0 0.38 2240
2 190 HB 0.5 5.0 0.21 0.50 1.80 90 280 33.0 0.35 2220
3 250 HB 0.5 5.0 0.21 0.45 1.50 90 250 33.0 0.33 2200
6 180 HB 0.5 5.0 0.21 0.45 1.20 60 280 33.0 0.32 2200
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 60 250 33.0 0.32 1180
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 60 210 33.0 0.30 1150
8 350 HB 0.5 3.5 0.18 0.40 1.00 60 180 22.7 0.30 1130
10 220 HB 0.5 4.0 0.18 0.40 1.20 35 190 22.5 0.30 1140
10 280 HB 0.5 4.0 0.18 0.40 1.20 35 150 22.5 0.30 1120
11 320 HB 0.5 3.0 0.18 0.35 0.80 35 130 22.2 0.28 1100
11 350 HB 0.5 3.0 0.18 0.35 0.80 35 110 22.2 0.28 990
14 180 HB 0.5 5.0 0.20 0.40 1.20 85 270 33.0 0.25 1190
14 240 HB 0.5 5.0 0.20 0.40 1.00 80 220 33.0 0.22 1170
14 290 HB 0.5 4.0 0.18 0.35 0.80 40 150 22.5 0.24 1100
14 310 HB 0.5 4.0 0.18 0.35 0.80 35 140 22.5 0.24 990
12 200 HB 0.5 5.0 0.18 0.40 0.70 85 250 22.5 0.20 1190
13 42 HRc 0.5 4.0 0.18 0.40 0.70 60 190 22.2 0.20 1130
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 60 250 33.0 0.30 1180
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 60 230 33.0 0.30 1160
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 60 190 33.0 0.30 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
DNMG 110408 NN – LT 1005
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 5.0 0.21 0.50 1.80 180 430 33.0 0.38 2265
2 190 HB 0.5 5.0 0.21 0.50 1.80 180 365 33.0 0.35 2240
3 250 HB 0.5 5.0 0.21 0.45 1.50 180 325 33.0 0.33 2220
6 180 HB 0.5 5.0 0.21 0.45 1.20 120 365 33.0 0.32 2220
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 325 33.0 0.32 2200
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 275 33.0 0.30 1165
8 350 HB 0.5 3.5 0.18 0.40 1.00 120 235 22.7 0.30 1145
10 220 HB 0.5 4.0 0.18 0.40 1.20 70 245 22.5 0.30 1155
10 280 HB 0.5 4.0 0.18 0.40 1.20 70 195 22.5 0.30 1130
11 320 HB 0.5 3.0 0.18 0.35 0.80 70 170 22.2 0.28 1110
11 350 HB 0.5 3.0 0.18 0.35 0.80 70 145 22.2 0.28 1100
15 150 HB 0.5 5.0 0.15 0.60 2.00 170 325 33.0 0.35 2220
15 200 HB 0.5 5.0 0.15 0.60 1.80 160 300 33.0 0.35 2200
16 250 HB 0.5 5.0 0.15 0.55 1.80 150 275 33.0 0.35 1175
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 325 33.0 0.30 2200
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 300 33.0 0.30 1175
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 245 33.0 0.30 1155
38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 130 22.0 0.25 990
38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 115 11.5 0.20 775
38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 105 11.0 0.18 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.25 0.40 40 80 11.5 0.18 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.20 0.30 30 65 11.0 0.15 445
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
Cast
Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
60
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300
2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260
3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240
6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260
4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240
5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200
8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180
10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180
10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140
11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120
11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110
14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260
14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210
14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140
14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140
12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240
13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180
15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240
15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220
16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200
17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240
17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220
18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335
36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660
37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550
38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990
38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880
38 55 HRc 0.0 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 00.9 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
DNMG 150404 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
61
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240
2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220
3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200
6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150
8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130
10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140
10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120
11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100
11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990
14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190
14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170
14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100
14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990
12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190
13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130
15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200
15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180
16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332
33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330
34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228
36 TiAl6V4 - 0.5 3.5 0.20 0.40 0.80 45 65 22.0 0.33 555
37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445
38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880
38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770
38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.25 0.40 40 60 11.5 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.20 0.30 30 50 11.0 0.15 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 3.0 0.40 280
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
10
8
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
1C35, Ck45, 1020, 1045, 1060, 28Mn6
St
eel
Non-alloyed
Low alloyed
DNMG 150408 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
62
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.50 1.80 90 330 33.0 0.38 2240
2 190 HB 0.5 5.0 0.21 0.50 1.80 90 280 33.0 0.35 2220
3 250 HB 0.5 5.0 0.21 0.45 1.50 90 250 33.0 0.33 2200
6 180 HB 0.5 5.0 0.21 0.45 1.20 60 280 33.0 0.32 2200
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 60 250 33.0 0.32 1180
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 60 210 33.0 0.30 1150
8 350 HB 0.5 3.5 0.18 0.40 1.00 60 180 22.7 0.30 1130
10 220 HB 0.5 4.0 0.18 0.40 1.20 35 190 22.5 0.30 1140
10 280 HB 0.5 4.0 0.18 0.40 1.20 35 150 22.5 0.30 1120
11 320 HB 0.5 3.0 0.18 0.35 0.80 35 130 22.2 0.28 1100
11 350 HB 0.5 3.0 0.18 0.35 0.80 35 110 22.2 0.28 990
14 180 HB 0.5 5.0 0.20 0.40 1.20 85 270 33.0 0.25 1190
14 240 HB 0.5 5.0 0.20 0.40 1.00 80 220 33.0 0.22 1170
14 290 HB 0.5 4.0 0.18 0.35 0.80 40 150 22.5 0.24 1100
14 310 HB 0.5 4.0 0.18 0.35 0.80 35 140 22.5 0.24 990
12 200 HB 0.5 5.0 0.18 0.40 0.70 85 250 22.5 0.20 1190
13 42 HRc 0.5 4.0 0.18 0.40 0.70 60 190 22.2 0.20 1130
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 60 250 33.0 0.30 1180
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 60 230 33.0 0.30 1160
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 60 190 33.0 0.30 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
DNMG 150408 NN – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.50 1.80 180 430 33.0 0.38 2265
2 190 HB 0.5 5.0 0.21 0.50 1.80 180 365 33.0 0.35 2240
3 250 HB 0.5 5.0 0.21 0.45 1.50 180 325 33.0 0.33 2220
6 180 HB 0.5 5.0 0.21 0.45 1.20 120 365 33.0 0.32 2220
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 325 33.0 0.32 2200
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 275 33.0 0.30 1165
8 350 HB 0.5 3.5 0.18 0.40 1.00 120 235 22.7 0.30 1145
10 220 HB 0.5 4.0 0.18 0.40 1.20 70 245 22.5 0.30 1155
10 280 HB 0.5 4.0 0.18 0.40 1.20 70 195 22.5 0.30 1130
11 320 HB 0.5 3.0 0.18 0.35 0.80 70 170 22.2 0.28 1110
11 350 HB 0.5 3.0 0.18 0.35 0.80 70 145 22.2 0.28 1100
15 150 HB 0.5 5.0 0.15 0.60 2.00 170 325 33.0 0.35 2220
15 200 HB 0.5 5.0 0.15 0.60 1.80 160 300 33.0 0.35 2200
16 250 HB 0.5 5.0 0.15 0.55 1.80 150 275 33.0 0.35 1175
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 325 33.0 0.30 2200
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 300 33.0 0.30 1175
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 245 33.0 0.30 1155
38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 130 22.0 0.25 990
38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 115 11.5 0.20 775
38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 105 11.0 0.18 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.25 0.40 40 80 11.5 0.18 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.20 0.30 30 65 11.0 0.15 445
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
7 GG20, GG40, EN-GJL-250,
No30B
8
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
DNMG 150408 NN – LT 1025
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
63
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240
2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220
3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200
6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150
8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130
10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140
10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120
11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100
11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990
14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190
14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170
14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100
14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990
12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190
13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130
15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200
15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180
16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332
33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330
34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228
36 TiAl6V4 - 0.5 3.5 0.20 0.40 0.80 45 65 22.0 0.33 555
37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445
38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880
38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770
38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.25 0.40 40 60 11.5 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.20 0.30 30 50 11.0 0.15 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 3.0 0.40 280
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
10
8
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
1C35, Ck45, 1020, 1045, 1060, 28Mn6
St
eel
Non-alloyed
Low alloyed
DNMG 150408 NX – LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
64
TURNING Machining Conditions
DNMG 150408 NX – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.18 0.50 1.71 90 330 33.0 0.36 2240
2 190 HB 0.5 5.0 0.18 0.50 1.71 90 280 33.0 0.33 2220
3 250 HB 0.5 5.0 0.18 0.45 1.43 90 250 33.0 0.31 2200
6 180 HB 0.5 5.0 0.18 0.45 1.14 60 280 33.0 0.30 2200
4,6 230 HB 0.5 4.0 0.18 0.45 1.14 60 250 33.0 0.30 1180
5,7 280 HB 0.5 4.0 0.16 0.40 1.14 60 210 33.0 0.29 1150
8 350 HB 0.5 3.5 0.16 0.40 0.95 60 180 22.7 0.29 1130
10 220 HB 0.5 4.0 0.16 0.40 1.14 35 190 22.5 0.29 1140
10 280 HB 0.5 4.0 0.16 0.40 1.14 35 150 22.5 0.29 1120
11 320 HB 0.5 3.0 0.16 0.35 0.76 35 130 22.2 0.27 1100
11 350 HB 0.5 3.0 0.16 0.35 0.76 35 110 22.2 0.27 990
14 180 HB 0.5 5.0 0.18 0.40 1.14 85 270 33.0 0.24 1190
14 240 HB 0.5 5.0 0.18 0.40 0.95 80 220 33.0 0.21 1170
14 290 HB 0.5 4.0 0.16 0.35 0.76 40 150 22.5 0.23 1100
14 310 HB 0.5 4.0 0.16 0.35 0.76 35 140 22.5 0.23 990
12 200 HB 0.5 5.0 0.16 0.40 0.67 85 250 22.5 0.19 1190
13 42 HRc 0.5 4.0 0.16 0.40 0.67 60 190 22.2 0.19 1130
17,19 150 HB 0.5 5.0 0.13 0.50 1.43 60 250 33.0 0.29 1180
17,19 200 HB 0.5 5.0 0.13 0.50 1.24 60 230 33.0 0.29 1160
18,20 250 HB 0.5 5.0 0.13 0.50 1.14 60 190 33.0 0.29 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
DNMG 150408 NX – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.18 0.50 1.71 180 430 33.0 0.36 2265
2 190 HB 0.5 5.0 0.18 0.50 1.71 180 365 33.0 0.33 2240
3 250 HB 0.5 5.0 0.18 0.45 1.43 180 325 33.0 0.31 2220
6 180 HB 0.5 5.0 0.18 0.45 1.14 120 365 33.0 0.30 2220
4,6 230 HB 0.5 4.0 0.18 0.45 1.14 120 325 33.0 0.30 2200
5,7 280 HB 0.5 4.0 0.16 0.40 1.14 120 275 33.0 0.29 1165
8 350 HB 0.5 3.5 0.16 0.40 0.95 120 235 22.7 0.29 1145
10 220 HB 0.5 4.0 0.16 0.40 1.14 70 245 22.5 0.29 1155
10 280 HB 0.5 4.0 0.16 0.40 1.14 70 195 22.5 0.29 1130
11 320 HB 0.5 3.0 0.16 0.35 0.76 70 170 22.2 0.27 1110
11 350 HB 0.5 3.0 0.16 0.35 0.76 70 145 22.2 0.27 1100
15 150 HB 0.5 5.0 0.13 0.60 1.90 170 325 33.0 0.33 2220
15 200 HB 0.5 5.0 0.13 0.60 1.71 160 300 33.0 0.33 2200
16 250 HB 0.5 5.0 0.13 0.55 1.71 150 275 33.0 0.33 1175
17,19 150 HB 0.5 5.0 0.13 0.50 1.43 120 325 33.0 0.29 2200
17,19 200 HB 0.5 5.0 0.13 0.50 1.24 120 300 33.0 0.29 1175
18,20 250 HB 0.5 5.0 0.13 0.50 1.14 120 245 33.0 0.29 1155
38 45 HRc 0.5 2.5 0.10 0.30 0.57 50 130 22.0 0.24 990
38 50 HRc 0.5 2.0 0.10 0.25 0.38 40 115 11.5 0.19 775
38 55 HRc 0.5 1.5 0.10 0.20 0.29 40 105 11.0 0.17 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.10 0.25 0.38 40 80 11.5 0.17 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.20 0.29 30 65 11.0 0.14 445
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
65
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.7 6.0 0.26 0.68 3.06 180 330 44.0 0.46 2240
2 190 HB 0.7 6.0 0.26 0.68 3.06 180 280 44.0 0.46 2220
3 250 HB 0.7 6.0 0.26 0.61 2.55 180 250 44.0 0.46 2200
6 180 HB 0.7 6.0 0.26 0.61 2.04 120 280 44.0 0.42 2200
4,6 230 HB 0.7 4.8 0.26 0.61 2.04 120 250 44.0 0.42 1180
5,7 280 HB 0.7 4.8 0.23 0.54 2.04 120 210 44.0 0.40 1150
8 350 HB 0.7 4.2 0.23 0.54 1.70 120 180 44.0 0.40 1130
10 220 HB 0.7 4.8 0.23 0.54 2.04 70 190 33.4 0.40 1140
10 280 HB 0.7 4.8 0.23 0.54 2.04 70 150 33.4 0.40 1120
11 320 HB 0.7 3.6 0.23 0.47 1.36 70 130 33.4 0.37 1100
11 350 HB 0.7 3.6 0.23 0.47 1.36 70 110 33.4 0.37 990
14 180 HB 0.7 6.0 0.25 0.54 2.04 170 270 44.0 0.40 1190
14 240 HB 0.7 6.0 0.25 0.54 1.70 160 220 44.0 0.38 1170
14 290 HB 0.7 4.8 0.23 0.47 1.36 80 150 33.4 0.32 1100
14 310 HB 0.7 4.8 0.23 0.47 1.36 70 140 33.4 0.32 990
12 200 HB 0.7 6.0 0.28 0.54 1.70 170 250 44.0 0.40 1190
13 42 HRc 0.7 4.8 0.28 0.54 1.70 120 190 33.0 0.35 1130
15 150 HB 0.7 6.0 0.20 0.81 3.40 170 250 44.0 0.46 2200
15 200 HB 0.7 6.0 0.20 0.81 3.06 160 230 44.0 0.46 1180
16 250 HB 0.7 6.0 0.20 0.74 3.06 150 210 44.0 0.46 1160
17,19 150 HB 0.7 6.0 0.20 0.68 2.55 120 250 44.0 0.40 1180
17,19 200 HB 0.7 6.0 0.20 0.68 2.21 120 230 44.0 0.40 1160
18,20 250 HB 0.7 6.0 0.20 0.68 2.04 120 190 44.0 0.40 1140
31,32 Incoloy 800 240 HB 0.7 3.6 0.25 0.47 1.19 25 45 22.7 0.37 332
33 Inconel 700 250 HB 0.7 3.6 0.25 0.47 1.19 25 45 22.7 0.37 330
34 Stellite 21 350 HB 0.7 3.6 0.25 0.47 1.19 23 40 22.7 0.37 228
36 TiAl6V4 - 0.7 4.8 0.25 0.54 1.36 45 65 22.7 0.44 555
37 T40 - 0.7 3.6 0.25 0.47 1.19 35 55 22.7 0.40 445
38 45 HRc 0.7 3.0 0.14 0.41 1.02 50 100 22.7 0.33 880
38 50 HRc 0.7 2.4 0.14 0.34 0.68 40 90 22.0 0.26 770
38 55 HRc 0.7 1.8 0.14 0.27 0.51 40 80 11.3 0.24 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.4 0.14 0.34 0.68 40 60 22.0 0.24 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.8 0.14 0.27 0.51 30 50 11.3 0.20 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.7 7.0 0.25 0.81 3.10 200 400 4.0 0.50 280
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
DNMG 150412 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
66
TURNING Machining Conditions
DNMG 150412 NN – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.7 6.0 0.26 0.68 3.06 90 330 44.0 0.50 2240
2 190 HB 0.7 6.0 0.26 0.68 3.06 90 280 44.0 0.46 2220
3 250 HB 0.7 6.0 0.26 0.61 2.55 90 250 44.0 0.44 2200
6 180 HB 0.7 6.0 0.26 0.61 2.04 60 280 44.0 0.42 2200
4,6 230 HB 0.7 4.8 0.26 0.61 2.04 60 250 44.0 0.42 1180
5,7 280 HB 0.7 4.8 0.23 0.54 2.04 60 210 44.0 0.40 1150
8 350 HB 0.7 4.2 0.23 0.54 1.70 60 180 33.6 0.40 1130
10 220 HB 0.7 4.8 0.23 0.54 2.04 35 190 33.4 0.40 1140
10 280 HB 0.7 4.8 0.23 0.54 2.04 35 150 33.4 0.40 1120
11 320 HB 0.7 3.6 0.23 0.47 1.36 35 130 22.9 0.37 1100
11 350 HB 0.7 3.6 0.23 0.47 1.36 35 110 22.9 0.37 990
14 180 HB 0.7 6.0 0.25 0.54 2.04 85 270 44.0 0.33 1190
14 240 HB 0.7 6.0 0.25 0.54 1.70 80 220 44.0 0.29 1170
14 290 HB 0.7 4.8 0.23 0.47 1.36 40 150 33.4 0.32 1100
14 310 HB 0.7 4.8 0.23 0.47 1.36 35 140 33.4 0.32 990
12 200 HB 0.7 6.0 0.23 0.54 1.19 85 250 33.4 0.26 1190
13 42 HRc 0.7 4.8 0.23 0.54 1.19 60 190 22.9 0.26 1130
17,19 150 HB 0.7 6.0 0.19 0.68 2.55 60 250 44.0 0.40 1180
17,19 200 HB 0.7 6.0 0.19 0.68 2.21 60 230 44.0 0.40 1160
18,20 250 HB 0.7 6.0 0.19 0.68 2.04 60 190 44.0 0.40 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
DNMG 150412 NN – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.7 6.0 0.26 0.68 3.06 180 430 44.0 0.50 2265
2 190 HB 0.7 6.0 0.26 0.68 3.06 180 365 44.0 0.46 2240
3 250 HB 0.7 6.0 0.26 0.61 2.55 180 325 44.0 0.44 2220
6 180 HB 0.7 6.0 0.26 0.61 2.04 120 365 44.0 0.42 2220
4,6 230 HB 0.7 4.8 0.26 0.61 2.04 120 325 44.0 0.42 2200
5,7 280 HB 0.7 4.8 0.23 0.54 2.04 120 275 44.0 0.40 1165
8 350 HB 0.7 4.2 0.23 0.54 1.70 120 235 33.6 0.40 1145
10 220 HB 0.7 4.8 0.23 0.54 2.04 70 245 33.4 0.40 1155
10 280 HB 0.7 4.8 0.23 0.54 2.04 70 195 33.4 0.40 1130
11 320 HB 0.7 3.6 0.23 0.47 1.36 70 170 22.9 0.37 1110
11 350 HB 0.7 3.6 0.23 0.47 1.36 70 145 22.9 0.37 1100
15 150 HB 0.7 6.0 0.19 0.81 3.40 170 325 44.0 0.46 2220
15 200 HB 0.7 6.0 0.19 0.81 3.06 160 300 44.0 0.46 2200
16 250 HB 0.7 6.0 0.19 0.74 3.06 150 275 44.0 0.46 1175
17,19 150 HB 0.7 6.0 0.19 0.68 2.55 120 325 44.0 0.40 2200
17,19 200 HB 0.7 6.0 0.19 0.68 2.21 120 300 44.0 0.40 1175
18,20 250 HB 0.7 6.0 0.19 0.68 2.04 120 245 44.0 0.40 1155
38 45 HRc 0.7 3.0 0.14 0.41 1.02 50 130 22.7 0.33 990
38 50 HRc 0.7 2.4 0.14 0.34 0.68 40 115 22.0 0.26 775
38 55 HRc 0.7 1.8 0.14 0.27 0.51 40 105 11.3 0.24 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.4 0.14 0.34 0.68 40 80 22.0 0.24 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.8 0.14 0.27 0.51 30 65 11.3 0.20 445
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
7 GG20, GG40, EN-GJL-250,
No30B
8
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
67
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300
2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260
3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240
6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260
4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240
5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200
8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180
10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180
10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140
11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120
11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110
14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260
14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210
14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140
14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140
12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240
13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180
15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240
15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220
16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200
17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240
17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220
18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335
36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660
37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550
38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990
38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880
38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 00.9 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
DNMG 150604 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
68
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240
2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220
3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200
6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150
8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130
10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140
10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120
11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100
11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990
14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190
14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170
14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100
14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990
12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190
13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130
15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200
15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180
16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332
33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330
34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228
36 TiAl6V4 - 0.5 3.5 0.20 0.40 0.80 45 65 22.0 0.33 555
37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445
38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880
38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770
38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.25 0.40 40 60 11.5 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.20 0.30 30 50 11.0 0.15 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 3.0 0.40 280
St
eel
Non-alloyed
Low alloyed
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
10
8
DNMG 150608 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
69
TURNINGMachining Conditions
DNMG 150608 NN – LT 1025
DNMG 150608 NN – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.50 1.80 90 330 33.0 0.38 2240
2 190 HB 0.5 5.0 0.21 0.50 1.80 90 280 33.0 0.35 2220
3 250 HB 0.5 5.0 0.21 0.45 1.50 90 250 33.0 0.33 2200
6 180 HB 0.5 5.0 0.21 0.45 1.20 60 280 33.0 0.32 2200
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 60 250 33.0 0.32 1180
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 60 210 33.0 0.30 1150
8 350 HB 0.5 3.5 0.18 0.40 1.00 60 180 22.7 0.30 1130
10 220 HB 0.5 4.0 0.18 0.40 1.20 35 190 22.5 0.30 1140
10 280 HB 0.5 4.0 0.18 0.40 1.20 35 150 22.5 0.30 1120
11 320 HB 0.5 3.0 0.18 0.35 0.80 35 130 22.2 0.28 1100
11 350 HB 0.5 3.0 0.18 0.35 0.80 35 110 22.2 0.28 990
14 180 HB 0.5 5.0 0.20 0.40 1.20 85 270 33.0 0.25 1190
14 240 HB 0.5 5.0 0.20 0.40 1.00 80 220 33.0 0.22 1170
14 290 HB 0.5 4.0 0.18 0.35 0.80 40 150 22.5 0.24 1100
14 310 HB 0.5 4.0 0.18 0.35 0.80 35 140 22.5 0.24 990
12 200 HB 0.5 5.0 0.18 0.40 0.70 85 250 22.5 0.20 1190
13 42 HRc 0.5 4.0 0.18 0.40 0.70 60 190 22.2 0.20 1130
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 60 250 33.0 0.30 1180
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 60 230 33.0 0.30 1160
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 60 190 33.0 0.30 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.50 1.80 180 430 33.0 0.38 2265
2 190 HB 0.5 5.0 0.21 0.50 1.80 180 365 33.0 0.35 2240
3 250 HB 0.5 5.0 0.21 0.45 1.50 180 325 33.0 0.33 2220
6 180 HB 0.5 5.0 0.21 0.45 1.20 120 365 33.0 0.32 2220
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 325 33.0 0.32 2200
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 275 33.0 0.30 1165
8 350 HB 0.5 3.5 0.18 0.40 1.00 120 235 22.7 0.30 1145
10 220 HB 0.5 4.0 0.18 0.40 1.20 70 245 22.5 0.30 1155
10 280 HB 0.5 4.0 0.18 0.40 1.20 70 195 22.5 0.30 1130
11 320 HB 0.5 3.0 0.18 0.35 0.80 70 170 22.2 0.28 1110
11 350 HB 0.5 3.0 0.18 0.35 0.80 70 145 22.2 0.28 1100
15 150 HB 0.5 5.0 0.15 0.60 2.00 170 325 33.0 0.35 2220
15 200 HB 0.5 5.0 0.15 0.60 1.80 160 300 33.0 0.35 2200
16 250 HB 0.5 5.0 0.15 0.55 1.80 150 275 33.0 0.35 1175
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 325 33.0 0.30 2200
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 300 33.0 0.30 1175
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 245 33.0 0.30 1155
38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 130 22.0 0.25 990
38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 115 11.5 0.20 775
38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 105 11.0 0.18 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.25 0.40 40 80 11.5 0.18 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.20 0.30 30 65 11.0 0.15 445
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
70
TURNING Machining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240
2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220
3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200
6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150
8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130
10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140
10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120
11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100
11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990
14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190
14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170
14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100
14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990
12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190
13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130
15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200
15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180
16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332
33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330
34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228
36 TiAl6V4 - 0.5 3.5 0.20 0.40 0.80 45 65 22.0 0.33 555
37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445
38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880
38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770
38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.25 0.40 40 60 11.5 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.20 0.30 30 50 11.0 0.15 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 3.0 0.40 280
St
eel
Non-alloyed
Low alloyed
Material Group Gr. N°
Suggested Starting Parameters
1C35, Ck45, 1020, 1045, 1060, 28Mn6
Amax [mm²]
D.O.C. [mm]VDI Group
Material Examples* HardnessFeed [mm/rev] Vc [m/min]
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
10
8
DNMG 150608 NX – LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
71
TURNINGMachining Conditions
DNMG 150608 NX – LT 1025
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 5.0 0.18 0.50 1.71 90 330 33.0 0.36 2240
2 190 HB 0.5 5.0 0.18 0.50 1.71 90 280 33.0 0.33 2220
3 250 HB 0.5 5.0 0.18 0.45 1.43 90 250 33.0 0.31 2200
6 180 HB 0.5 5.0 0.18 0.45 1.14 60 280 33.0 0.30 2200
4,6 230 HB 0.5 4.0 0.18 0.45 1.14 60 250 33.0 0.30 1180
5,7 280 HB 0.5 4.0 0.16 0.40 1.14 60 210 33.0 0.29 1150
8 350 HB 0.5 3.5 0.16 0.40 0.95 60 180 22.7 0.29 1130
10 220 HB 0.5 4.0 0.16 0.40 1.14 35 190 22.5 0.29 1140
10 280 HB 0.5 4.0 0.16 0.40 1.14 35 150 22.5 0.29 1120
11 320 HB 0.5 3.0 0.16 0.35 0.76 35 130 22.2 0.27 1100
11 350 HB 0.5 3.0 0.16 0.35 0.76 35 110 22.2 0.27 990
14 180 HB 0.5 5.0 0.18 0.40 1.14 85 270 33.0 0.24 1190
14 240 HB 0.5 5.0 0.18 0.40 0.95 80 220 33.0 0.21 1170
14 290 HB 0.5 4.0 0.16 0.35 0.76 40 150 22.5 0.23 1100
14 310 HB 0.5 4.0 0.16 0.35 0.76 35 140 22.5 0.23 990
12 200 HB 0.5 5.0 0.16 0.40 0.67 85 250 22.5 0.19 1190
13 42 HRc 0.5 4.0 0.16 0.40 0.67 60 190 22.2 0.19 1130
17,19 150 HB 0.5 5.0 0.13 0.50 1.43 60 250 33.0 0.29 1180
17,19 200 HB 0.5 5.0 0.13 0.50 1.24 60 230 33.0 0.29 1160
18,20 250 HB 0.5 5.0 0.13 0.50 1.14 60 190 33.0 0.29 1140
Amax [mm²]
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
DNMG 150608 NX – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.18 0.50 1.71 180 430 33.0 0.36 2265
2 190 HB 0.5 5.0 0.18 0.50 1.71 180 365 33.0 0.33 2240
3 250 HB 0.5 5.0 0.18 0.45 1.43 180 325 33.0 0.31 2220
6 180 HB 0.5 5.0 0.18 0.45 1.14 120 365 33.0 0.30 2220
4,6 230 HB 0.5 4.0 0.18 0.45 1.14 120 325 33.0 0.30 2200
5,7 280 HB 0.5 4.0 0.16 0.40 1.14 120 275 33.0 0.29 1165
8 350 HB 0.5 3.5 0.16 0.40 0.95 120 235 22.7 0.29 1145
10 220 HB 0.5 4.0 0.16 0.40 1.14 70 245 22.5 0.29 1155
10 280 HB 0.5 4.0 0.16 0.40 1.14 70 195 22.5 0.29 1130
11 320 HB 0.5 3.0 0.16 0.35 0.76 70 170 22.2 0.27 1110
11 350 HB 0.5 3.0 0.16 0.35 0.76 70 145 22.2 0.27 1100
15 150 HB 0.5 5.0 0.13 0.60 1.90 170 325 33.0 0.33 2220
15 200 HB 0.5 5.0 0.13 0.60 1.71 160 300 33.0 0.33 2200
16 250 HB 0.5 5.0 0.13 0.55 1.71 150 275 33.0 0.33 1175
17,19 150 HB 0.5 5.0 0.13 0.50 1.43 120 325 33.0 0.29 2200
17,19 200 HB 0.5 5.0 0.13 0.50 1.24 120 300 33.0 0.29 1175
18,20 250 HB 0.5 5.0 0.13 0.50 1.14 120 245 33.0 0.29 1155
38 45 HRc 0.5 2.5 0.10 0.30 0.57 50 130 22.0 0.24 990
38 50 HRc 0.5 2.0 0.10 0.25 0.38 40 115 11.5 0.19 775
38 55 HRc 0.5 1.5 0.10 0.20 0.29 40 105 11.0 0.17 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.10 0.25 0.38 40 80 11.5 0.17 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.20 0.29 30 65 11.0 0.14 445
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
Cast
Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
72
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.7 6.0 0.26 0.68 3.06 180 330 44.0 0.46 2240
2 190 HB 0.7 6.0 0.26 0.68 3.06 180 280 44.0 0.46 2220
3 250 HB 0.7 6.0 0.26 0.61 2.55 180 250 44.0 0.46 2200
6 180 HB 0.7 6.0 0.26 0.61 2.04 120 280 44.0 0.42 2200
4,6 230 HB 0.7 4.8 0.26 0.61 2.04 120 250 44.0 0.42 1180
5,7 280 HB 0.7 4.8 0.23 0.54 2.04 120 210 44.0 0.40 1150
8 350 HB 0.7 4.2 0.23 0.54 1.70 120 180 44.0 0.40 1130
10 220 HB 0.7 4.8 0.23 0.54 2.04 70 190 33.4 0.40 1140
10 280 HB 0.7 4.8 0.23 0.54 2.04 70 150 33.4 0.40 1120
11 320 HB 0.7 3.6 0.23 0.47 1.36 70 130 33.4 0.37 1100
11 350 HB 0.7 3.6 0.23 0.47 1.36 70 110 33.4 0.37 990
14 180 HB 0.7 6.0 0.25 0.54 2.04 170 270 44.0 0.40 1190
14 240 HB 0.7 6.0 0.25 0.54 1.70 160 220 44.0 0.38 1170
14 290 HB 0.7 4.8 0.23 0.47 1.36 80 150 33.4 0.32 1100
14 310 HB 0.7 4.8 0.23 0.47 1.36 70 140 33.4 0.32 990
12 200 HB 0.7 6.0 0.28 0.54 1.70 170 250 44.0 0.40 1190
13 42 HRc 0.7 4.8 0.28 0.54 1.70 120 190 33.0 0.35 1130
15 150 HB 0.7 6.0 0.20 0.81 3.40 170 250 44.0 0.46 2200
15 200 HB 0.7 6.0 0.20 0.81 3.06 160 230 44.0 0.46 1180
16 250 HB 0.7 6.0 0.20 0.74 3.06 150 210 44.0 0.46 1160
17,19 150 HB 0.7 6.0 0.20 0.68 2.55 120 250 44.0 0.40 1180
17,19 200 HB 0.7 6.0 0.20 0.68 2.21 120 230 44.0 0.40 1160
18,20 250 HB 0.7 6.0 0.20 0.68 2.04 120 190 44.0 0.40 1140
31,32 Incoloy 800 240 HB 0.7 3.6 0.25 0.47 1.19 25 45 22.7 0.37 332
33 Inconel 700 250 HB 0.7 3.6 0.25 0.47 1.19 25 45 22.7 0.37 330
34 Stellite 21 350 HB 0.7 3.6 0.25 0.47 1.19 23 40 22.7 0.37 228
36 TiAl6V4 - 0.7 4.8 0.25 0.54 1.36 45 65 22.7 0.44 555
37 T40 - 0.7 3.6 0.25 0.47 1.19 35 55 22.7 0.40 445
38 45 HRc 0.7 3.0 0.14 0.41 1.02 50 100 22.7 0.33 880
38 50 HRc 0.7 2.4 0.14 0.34 0.68 40 90 22.0 0.26 770
38 55 HRc 0.7 1.8 0.14 0.27 0.51 40 80 11.3 0.24 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.4 0.14 0.34 0.68 40 60 22.0 0.24 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.8 0.14 0.27 0.51 30 50 11.3 0.20 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.7 7.0 0.25 0.81 3.10 200 400 4.0 0.50 280
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
DNMG 150612 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
73
TURNING
VC
Productivity
Stainless Steel
VC
D N U X0°
Shape Clearance Angle Fixing,Chipbreaker
55°
l
mØ d
s
Toleranced ± 0.08m ± 0.13s ± 0.13
F M R
Application Guide
Insert Designation s r Catalog Nr.l
LT 10 Multi-MatTM General Usage – Standard
T00021570.806.3515DNUX 150608 R11 LT10
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00027930.806.3515DNUX 150608 R11 LT 1000
LT 1000 Multi-MatTM General Usage – Premium
55° nose angle inserts with four cutting edges. Excellent chip control and low cutting force. Suitable for conventional turning operations and long shafts.
DNUX
74
TURNING Machining Conditions
DNUX 150608 R11 – LT 10 | LT 1000
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 5.0 0.18 0.50 1.70 180 330 33.0 0.33 2240
2 190 HB 0.5 5.0 0.18 0.50 1.70 180 280 33.0 0.33 2220
3 250 HB 0.5 5.0 0.18 0.45 1.45 180 250 33.0 0.33 2200
6 180 HB 0.5 5.0 0.18 0.45 1.15 120 280 33.0 0.30 2200
4,6 230 HB 0.5 4.0 0.18 0.45 1.15 120 250 33.0 0.30 1180
5,7 280 HB 0.5 4.0 0.16 0.40 1.15 120 210 33.0 0.29 1150
8 350 HB 0.5 3.5 0.16 0.40 0.95 120 180 33.0 0.29 1130
10 220 HB 0.5 4.0 0.16 0.40 1.15 70 190 22.5 0.29 1140
10 280 HB 0.5 4.0 0.16 0.40 1.15 70 150 22.5 0.29 1120
11 320 HB 0.5 3.0 0.16 0.35 0.75 70 130 22.5 0.27 1100
11 350 HB 0.5 3.0 0.16 0.35 0.75 70 110 22.5 0.27 990
14 180 HB 0.5 5.0 0.18 0.40 1.15 170 270 33.0 0.24 1190
14 240 HB 0.5 5.0 0.18 0.40 0.95 160 220 33.0 0.21 1170
14 290 HB 0.5 4.0 0.16 0.35 0.75 80 150 22.5 0.27 1100
14 310 HB 0.5 4.0 0.16 0.35 0.75 70 140 22.5 0.27 990
12 200 HB 0.5 5.0 0.19 0.40 0.95 170 250 22.5 0.29 1190
13 42 HRc 0.5 4.0 0.19 0.40 0.95 120 190 22.2 0.24 1130
15 150 HB 0.5 5.0 0.13 0.60 1.90 170 250 33.0 0.33 2200
15 200 HB 0.5 5.0 0.13 0.60 1.70 160 230 33.0 0.33 1180
16 250 HB 0.5 5.0 0.13 0.55 1.70 150 210 33.0 0.33 1160
17,19 150 HB 0.5 5.0 0.13 0.50 1.45 120 250 33.0 0.29 1180
17,19 200 HB 0.5 5.0 0.13 0.50 1.25 120 230 33.0 0.29 1160
18,20 250 HB 0.5 5.0 0.13 0.50 1.15 120 190 33.0 0.29 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.18 0.35 0.65 25 45 22.0 0.27 330
33 Inconel 700 250 HB 0.5 3.0 0.18 0.35 0.65 25 45 22.0 0.27 330
34 Stellite 21 350 HB 0.5 3.0 0.18 0.35 0.65 25 40 22.0 0.27 330
36 TiAl6V4 - 0.5 3.5 0.18 0.40 0.75 45 65 22.0 0.31 555
37 T40 - 0.5 3.0 0.18 0.35 0.65 35 55 22.0 0.29 445
38 45 HRc 0.5 2.5 0.10 0.30 0.55 50 100 22.0 0.24 880
38 50 HRc 0.5 2.0 0.10 0.25 0.40 40 90 11.5 0.19 770
38 55 HRc 0.5 1.5 0.10 0.20 0.30 40 80 11.0 0.17 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.10 0.25 0.40 40 60 11.5 0.17 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.20 0.30 30 50 11.0 0.14 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.18 0.60 1.70 200 400 33.0 0.38 280
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
10
8
Ferritic & Martensitic 6
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based
Cast
Iron
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5X2CrNiN23-4,
S31500
410, X6Cr17, 17-4 PH, 430
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
2
Suggested Starting Parameters
1C35, Ck45, 1020, 1045, 1060, 28Mn6
Amax [mm²]
D.O.C. [mm]VDI Group
Material Examples* HardnessFeed [mm/rev] Vc [m/min]
St
eel
Non-alloyed
Low alloyed
Material Group Gr. N°
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
75
TURNING
KNUX 160405 L LT 10
VC
Productivity
Stainless Steel
VC
K N U X0°
Shape Clearance Angle
Ø d
l
m
Toleranced ± 0.08m ± 0.13s ± 0.13
Fixing, Chipbreaker
55°
s
F M R
Application Guide
Insert Designation s r Catalog Nr.l
LT 10 Multi-MatTM General Usage – Standard
T0000951
T0003884
0.50
0.50
4.76
4.76
16
16
KNUX 160405 R LT 10
55
A 55° nose angle inserts with two cutting edges. Popular insert with excellent chip control and low cutting force. Suitable for conventional turning operations.
KNUX
76
TURNING Machining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.2 5.0 0.11 0.23 0.85 180 330 33.0 0.18 3300
2 190 HB 0.2 4.2 0.11 0.22 0.73 180 280 33.0 0.18 2260
3 250 HB 0.2 4.2 0.11 0.20 0.68 180 250 33.0 0.18 2240
6 180 HB 0.2 4.2 0.10 0.20 0.71 120 280 33.0 0.15 2260
4,6 230 HB 0.2 4.2 0.10 0.20 0.68 120 250 33.0 0.15 2240
5,7 280 HB 0.2 3.3 0.10 0.18 0.56 120 210 33.0 0.15 2200
8 350 HB 0.2 3.3 0.10 0.18 0.51 120 180 33.0 0.15 1180
10 220 HB 0.2 4.2 0.09 0.18 0.56 70 190 22.0 0.12 1180
10 280 HB 0.2 4.2 0.09 0.16 0.56 70 150 22.0 0.12 1140
11 320 HB 0.2 3.3 0.09 0.14 0.45 70 130 22.0 0.12 1120
11 350 HB 0.2 3.3 0.09 0.14 0.37 70 110 22.0 0.12 1110
14 180 HB 0.2 4.2 0.10 0.18 0.60 170 270 33.0 0.15 2260
14 240 HB 0.2 4.2 0.10 0.18 0.50 160 220 33.0 0.15 2210
14 290 HB 0.2 3.3 0.09 0.14 0.40 80 150 22.0 0.15 1140
14 310 HB 0.2 3.3 0.09 0.14 0.40 70 140 22.0 0.15 1140
12 200 HB 0.2 4.2 0.10 0.18 0.50 170 250 33.0 0.15 2240
13 42 HRc 0.2 3.3 0.10 0.16 0.45 120 190 22.0 0.15 1180
15 150 HB 0.2 5.0 0.08 0.20 0.85 170 250 33.0 0.18 2240
15 200 HB 0.2 5.0 0.08 0.20 0.75 160 230 33.0 0.18 2220
16 250 HB 0.2 5.0 0.08 0.20 0.65 150 210 33.0 0.18 2200
17,19 150 HB 0.2 4.2 0.08 0.18 0.68 120 250 22.5 0.15 2240
17,19 200 HB 0.2 4.2 0.08 0.18 0.60 120 230 22.5 0.15 2220
18,20 250 HB 0.2 4.2 0.08 0.18 0.56 120 190 22.5 0.15 1180
31,32 Incoloy 800 240 HB 0.2 3.3 0.09 0.15 0.40 25 50 22.0 0.12 440
33 Inconel 700 250 HB 0.2 3.3 0.09 0.15 0.40 25 50 22.0 0.12 440
34 Stellite 21 350 HB 0.2 3.3 0.09 0.15 0.40 23 45 22.0 0.12 335
36 TiAl6V4 - 0.2 3.3 0.09 0.16 0.45 45 65 22.0 0.15 660
37 T40 - 0.2 3.3 0.09 0.14 0.40 35 60 22.0 0.12 550
38 45 HRc 0.2 3.0 0.05 0.12 0.28 50 100 11.8 0.11 990
38 50 HRc 0.2 2.5 0.05 0.10 0.24 40 90 11.4 0.09 880
38 55 HRc 0.2 2.3 0.05 0.09 0.18 40 80 11.2 0.07 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.2 2.7 0.05 0.12 0.24 40 60 11.8 0.11 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.2 2.3 0.05 0.09 0.18 30 50 11.2 0.07 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.2 6.6 0.10 0.30 0.99 200 400 3.0 0.20 350
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
KNUX 160405 L/R – LT 10
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
77
TURNING
FProductivity
Stainless Steel
VC
R C M T7° Ø d
Shape Clearance Angle Tolerances ± 0.13For l = 06/08/10, d ± 0.05 m ± 0.08 For l = 12, d ± 0.08 m ± 0.13
Fixing,Chipbreaker
s
l
F M R
Application Guide
Insert Designation s r Catalog Nr.l
LT 10 Multi-MatTM General Usage – Standard
T00000936.004.7612RCMT 1204 M0 LT 10
T00000925.003.9710RCMT 10T3 M0 LT 10
T00000914.003.188RCMT 0803 M0 LT 10
T00000903.002.386RCMT 0602 M0 LT 10
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00019176.004.7612RCMT 1204 M0 LT 1000
T00019165.003.9710RCMT 10T3 M0 LT 1000
T00019154.003.188RCMT 0803 M0 LT 1000
T00019143.002.386RCMT 0602 M0 LT 1000
LT 1000 Multi-MatTM General Usage – Premium
Round inserts with positive rake angle and excellent edge resistance. Suitable for profiling operations of mill rolls and aerospace parts
RCMT
78
TURNING Machining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 2.0 0.15 0.40 0.64 180 330 11.0 0.35 2240
2 190 HB 0.5 2.0 0.15 0.40 0.64 180 280 11.0 0.35 2220
3 250 HB 0.5 1.5 0.15 0.35 0.56 180 250 11.0 0.30 2200
6 180 HB 0.5 2.0 0.15 0.35 0.56 120 280 11.0 0.30 2200
4,6 230 HB 0.5 2.0 0.15 0.35 0.48 120 250 11.0 0.30 1180
5,7 280 HB 0.5 2.0 0.15 0.35 0.40 120 210 11.0 0.30 1150
8 350 HB 0.5 1.5 0.15 0.35 0.36 120 180 11.0 0.30 1130
10 220 HB 0.5 2.0 0.13 0.35 0.48 70 190 11.0 0.30 1140
10 280 HB 0.5 2.0 0.13 0.30 0.40 70 150 11.0 0.28 1120
11 320 HB 0.5 1.5 0.13 0.30 0.32 70 130 11.0 0.28 1100
11 350 HB 0.5 1.5 0.13 0.30 0.26 70 110 11.0 0.28 990
14 180 HB 0.5 2.0 0.14 0.35 0.32 170 270 11.0 0.32 2220
14 240 HB 0.5 2.0 0.14 0.32 0.32 160 220 11.0 0.32 1190
14 290 HB 0.5 1.5 0.13 0.30 0.30 80 150 11.0 0.28 1100
14 310 HB 0.5 1.5 0.13 0.30 0.30 70 140 11.0 0.28 990
12 200 HB 0.5 2.0 0.15 0.35 0.32 170 250 11.0 0.32 2210
13 42 HRc 0.5 2.0 0.15 0.30 0.30 120 190 11.0 0.28 1140
15 150 HB 0.5 2.0 0.11 0.45 0.70 170 250 11.0 0.35 2200
15 200 HB 0.5 2.0 0.11 0.45 0.65 160 230 11.0 0.35 1180
16 250 HB 0.5 2.0 0.11 0.45 0.60 150 210 11.0 0.35 1160
17,19 150 HB 0.5 2.0 0.11 0.35 0.60 120 250 11.0 0.30 1180
17,19 200 HB 0.5 2.0 0.11 0.35 0.50 120 230 11.0 0.30 1160
18,20 250 HB 0.5 2.0 0.11 0.35 0.45 120 190 11.0 0.30 1140
31,32 Incoloy 800 240 HB 0.5 1.5 0.13 0.30 0.30 25 50 11.0 0.28 333
33 Inconel 700 250 HB 0.5 1.5 0.13 0.30 0.30 25 50 11.0 0.28 330
34 Stellite 21 350 HB 0.5 1.5 0.13 0.30 0.30 23 45 11.0 0.28 228
36 TiAl6V4 - 0.5 1.5 0.13 0.32 0.32 45 65 11.0 0.30 555
37 T40 - 0.5 1.5 0.13 0.30 0.30 35 60 11.0 0.28 445
38 45 HRc 0.5 1.2 0.05 0.22 0.20 50 100 00.9 0.18 880
38 50 HRc 0.5 1.0 0.05 0.18 0.17 40 90 00.7 0.16 770
38 55 HRc 0.3 0.8 0.05 0.14 0.12 40 80 00.6 0.12 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.2 0.05 0.22 0.17 40 60 00.9 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 0.8 0.05 0.14 0.10 30 50 00.6 0.12 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 2.0 0.15 0.40 0.70 200 400 1.0 0.35 280
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
RCMT 0602 M0 – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
79
TURNINGMachining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 2.4 0.15 0.40 0.77 180 330 11.2 0.35 2240
2 190 HB 0.5 2.4 0.15 0.40 0.77 180 280 11.2 0.35 2220
3 250 HB 0.5 1.8 0.15 0.35 0.67 180 250 11.2 0.30 2200
6 180 HB 0.5 2.4 0.15 0.35 0.67 120 280 11.2 0.30 2200
4,6 230 HB 0.5 2.4 0.15 0.35 0.58 120 250 11.2 0.30 1180
5,7 280 HB 0.5 2.4 0.15 0.35 0.48 120 210 11.2 0.30 1150
8 350 HB 0.5 1.8 0.15 0.35 0.43 120 180 11.2 0.30 1130
10 220 HB 0.5 2.4 0.13 0.35 0.58 70 190 11.2 0.30 1140
10 280 HB 0.5 2.4 0.13 0.30 0.48 70 150 11.2 0.28 1120
11 320 HB 0.5 1.8 0.13 0.30 0.38 70 130 11.2 0.28 1100
11 350 HB 0.5 1.8 0.13 0.30 0.31 70 110 11.2 0.28 990
14 180 HB 0.5 2.4 0.14 0.35 0.38 170 270 11.2 0.32 2220
14 240 HB 0.5 2.4 0.14 0.32 0.38 160 220 11.2 0.32 1190
14 290 HB 0.5 1.8 0.13 0.30 0.36 80 150 11.2 0.28 1100
14 310 HB 0.5 1.8 0.13 0.30 0.36 70 140 11.2 0.28 990
12 200 HB 0.5 2.4 0.15 0.35 0.38 170 250 11.2 0.32 2210
13 42 HRc 0.5 2.4 0.15 0.30 0.36 120 190 11.2 0.28 1140
15 150 HB 0.5 2.4 0.11 0.45 0.84 170 250 11.2 0.35 2200
15 200 HB 0.5 2.4 0.11 0.45 0.78 160 230 11.2 0.35 1180
16 250 HB 0.5 2.4 0.11 0.45 0.72 150 210 11.2 0.35 1160
17,19 150 HB 0.5 2.4 0.11 0.35 0.72 120 250 11.2 0.30 1180
17,19 200 HB 0.5 2.4 0.11 0.35 0.60 120 230 11.2 0.30 1160
18,20 250 HB 0.5 2.4 0.11 0.35 0.54 120 190 11.2 0.30 1140
31,32 Incoloy 800 240 HB 0.5 1.8 0.13 0.30 0.36 25 50 11.2 0.28 333
33 Inconel 700 250 HB 0.5 1.8 0.13 0.30 0.36 25 50 11.2 0.28 330
34 Stellite 21 350 HB 0.5 1.8 0.13 0.30 0.36 23 45 11.2 0.28 228
36 TiAl6V4 - 0.5 1.8 0.13 0.32 0.38 45 65 11.2 0.30 555
37 T40 - 0.5 1.8 0.13 0.30 0.36 35 60 11.2 0.28 445
38 45 HRc 0.5 1.4 0.05 0.22 0.24 50 100 11.1 0.18 880
38 50 HRc 0.5 1.2 0.05 0.18 0.20 40 90 00.8 0.16 770
38 55 HRc 0.3 1.0 0.05 0.14 0.14 40 80 00.7 0.12 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.4 0.05 0.22 0.20 40 60 11.1 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.0 0.05 0.14 0.12 30 50 00.7 0.12 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 2.4 0.15 0.40 0.84 200 400 1.2 0.35 280
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
RCMT 0803 M0 – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
80
TURNING Machining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 2.8 0.15 0.40 0.90 180 330 11.4 0.35 2240
2 190 HB 0.5 2.8 0.15 0.40 0.90 180 280 11.4 0.35 2220
3 250 HB 0.5 2.1 0.15 0.35 0.78 180 250 11.4 0.30 2200
6 180 HB 0.5 2.8 0.15 0.35 0.78 120 280 11.4 0.30 2200
4,6 230 HB 0.5 2.8 0.15 0.35 0.67 120 250 11.4 0.30 1180
5,7 280 HB 0.5 2.8 0.15 0.35 0.56 120 210 11.4 0.30 1150
8 350 HB 0.5 2.1 0.15 0.35 0.50 120 180 11.4 0.30 1130
10 220 HB 0.5 2.8 0.13 0.35 0.67 70 190 11.4 0.30 1140
10 280 HB 0.5 2.8 0.13 0.30 0.56 70 150 11.4 0.28 1120
11 320 HB 0.5 2.1 0.13 0.30 0.45 70 130 11.4 0.28 1100
11 350 HB 0.5 2.1 0.13 0.30 0.36 70 110 11.4 0.28 990
14 180 HB 0.5 2.8 0.14 0.35 0.45 170 270 11.4 0.32 2220
14 240 HB 0.5 2.8 0.14 0.32 0.45 160 220 11.4 0.32 1190
14 290 HB 0.5 2.1 0.13 0.30 0.42 80 150 11.4 0.28 1100
14 310 HB 0.5 2.1 0.13 0.30 0.42 70 140 11.4 0.28 990
12 200 HB 0.5 2.8 0.15 0.35 0.45 170 250 11.4 0.32 2210
13 42 HRc 0.5 2.8 0.15 0.30 0.42 120 190 11.4 0.28 1140
15 150 HB 0.5 2.8 0.11 0.45 0.98 170 250 11.4 0.35 2200
15 200 HB 0.5 2.8 0.11 0.45 0.91 160 230 11.4 0.35 1180
16 250 HB 0.5 2.8 0.11 0.45 0.84 150 210 11.4 0.35 1160
17,19 150 HB 0.5 2.8 0.11 0.35 0.84 120 250 11.4 0.30 1180
17,19 200 HB 0.5 2.8 0.11 0.35 0.70 120 230 11.4 0.30 1160
18,20 250 HB 0.5 2.8 0.11 0.35 0.63 120 190 11.4 0.30 1140
31,32 Incoloy 800 240 HB 0.5 2.1 0.13 0.30 0.42 25 50 11.4 0.28 333
33 Inconel 700 250 HB 0.5 2.1 0.13 0.30 0.42 25 50 11.4 0.28 330
34 Stellite 21 350 HB 0.5 2.1 0.13 0.30 0.42 23 45 11.4 0.28 228
36 TiAl6V4 - 0.5 2.1 0.13 0.32 0.45 45 65 11.4 0.30 555
37 T40 - 0.5 2.1 0.13 0.30 0.42 35 60 11.4 0.28 445
38 45 HRc 0.5 1.7 0.05 0.22 0.28 50 100 11.3 0.18 880
38 50 HRc 0.5 1.4 0.05 0.18 0.24 40 90 11.0 0.16 770
38 55 HRc 0.3 1.1 0.05 0.14 0.17 40 80 00.8 0.12 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.7 0.05 0.22 0.24 40 60 11.3 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.1 0.05 0.14 0.14 30 50 00.8 0.12 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 2.8 0.15 0.40 0.98 200 400 1.4 0.35 280
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
RCMT 10T3 M0 – LT 10 | LT 1000
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
81
TURNINGMachining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 3.2 0.15 0.40 1.54 180 330 22.0 0.37 2240
2 190 HB 0.5 3.2 0.15 0.40 1.54 180 280 22.0 0.37 2220
3 250 HB 0.5 2.4 0.15 0.35 1.34 180 250 22.0 0.32 2200
6 180 HB 0.5 3.2 0.15 0.35 1.34 120 280 22.0 0.32 2200
4,6 230 HB 0.5 3.2 0.15 0.35 1.15 120 250 22.0 0.32 1180
5,7 280 HB 0.5 3.2 0.15 0.35 0.96 120 210 22.0 0.32 1150
8 350 HB 0.5 2.4 0.15 0.35 0.86 120 180 22.0 0.32 1130
10 220 HB 0.5 3.2 0.13 0.35 1.15 70 190 22.0 0.32 1140
10 280 HB 0.5 3.2 0.13 0.30 0.96 70 150 22.0 0.29 1120
11 320 HB 0.5 2.4 0.13 0.30 0.77 70 130 22.0 0.29 1100
11 350 HB 0.5 2.4 0.13 0.30 0.62 70 110 22.0 0.25 990
14 180 HB 0.5 3.2 0.14 0.35 0.77 170 270 22.0 0.32 2220
14 240 HB 0.5 3.2 0.14 0.32 0.77 160 220 22.0 0.30 1190
14 290 HB 0.5 2.4 0.13 0.30 0.72 80 150 22.0 0.29 1100
14 310 HB 0.5 2.4 0.13 0.30 0.72 70 140 22.0 0.29 990
12 200 HB 0.5 3.2 0.15 0.35 0.77 170 250 22.0 0.26 2210
13 42 HRc 0.5 3.2 0.15 0.30 0.72 120 190 22.0 0.23 1140
15 150 HB 0.5 3.2 0.11 0.45 1.68 170 250 22.0 0.37 2200
15 200 HB 0.5 3.2 0.11 0.45 1.56 160 230 22.0 0.37 1180
16 250 HB 0.5 3.2 0.11 0.45 1.44 150 210 22.0 0.37 1160
17,19 150 HB 0.5 3.2 0.11 0.35 1.44 120 250 22.0 0.32 1180
17,19 200 HB 0.5 3.2 0.11 0.35 1.20 120 230 22.0 0.32 1160
18,20 250 HB 0.5 3.2 0.11 0.35 1.08 120 190 22.0 0.32 1140
31,32 Incoloy 800 240 HB 0.5 2.4 0.13 0.30 0.72 25 50 22.0 0.29 335
33 Inconel 700 250 HB 0.5 2.4 0.13 0.30 0.72 25 50 22.0 0.29 330
34 Stellite 21 350 HB 0.5 2.4 0.13 0.30 0.72 25 45 22.0 0.29 330
36 TiAl6V4 - 0.5 2.4 0.13 0.32 0.77 45 65 22.0 0.32 555
37 T40 - 0.5 2.4 0.13 0.30 0.72 35 60 22.0 0.29 445
38 45 HRc 0.5 1.9 0.05 0.22 0.48 50 100 11.8 0.19 880
38 50 HRc 0.5 1.6 0.05 0.18 0.41 40 90 11.4 0.17 770
38 55 HRc 0.3 1.3 0.05 0.14 0.29 40 80 11.2 0.13 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.9 0.05 0.22 0.41 40 60 11.8 0.19 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.3 0.05 0.14 0.24 30 50 11.2 0.13 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.2 0.15 0.40 1.68 200 400 2.0 0.37 280
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
RCMT 1204 M0 – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
82
TURNING
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
S C M T7°
l
Shape Clearance Angle Tolerance d ± 0.05m ± 0.08s ± 0.13
90° Ø dm
Fixing,Chipbreaker
s
F M R
Application Guide
Insert Designation s r Catalog Nr.l
LT 10 Multi-MatTM General Usage – Standard
T00014580.803.979SCMT 09T308 NN LT 10
T00014590.403.979SCMT 09T304 NN LT 10
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00019190.803.979SCMT 09T308 NN LT 1000
T00019180.403.979SCMT 09T304 NN LT 1000
LT 1000 Multi-MatTM General Usage – Premium
TURNING
90°
FProductivity
Stainless Steel
VC
Square inserts with a positive rake angle and excellent cutting edge resistance. Suitable for boring operations.
83
TURNINGMachining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.3 4.0 0.11 0.26 0.72 180 330 22.5 0.18 3300
2 190 HB 0.3 3.3 0.11 0.25 0.62 180 280 22.5 0.18 2260
3 250 HB 0.3 3.3 0.11 0.23 0.58 180 250 22.5 0.18 2240
6 180 HB 0.3 3.3 0.10 0.23 0.60 120 280 22.5 0.14 2260
4,6 230 HB 0.3 3.3 0.10 0.23 0.58 120 250 22.5 0.14 2240
5,7 280 HB 0.3 2.7 0.10 0.21 0.48 120 210 22.5 0.13 2200
8 350 HB 0.3 2.7 0.10 0.21 0.43 120 180 22.5 0.13 1180
10 220 HB 0.3 3.3 0.09 0.21 0.48 70 190 22.1 0.10 1180
10 280 HB 0.3 3.3 0.09 0.18 0.48 70 150 22.1 0.10 1140
11 320 HB 0.3 2.7 0.09 0.16 0.38 70 130 22.1 0.10 1120
11 350 HB 0.3 2.7 0.09 0.16 0.31 70 110 22.1 0.10 1110
14 180 HB 0.3 3.3 0.08 0.21 0.38 170 270 22.5 0.09 2260
14 240 HB 0.3 3.3 0.08 0.21 0.31 160 220 22.5 0.08 2210
14 290 HB 0.3 2.7 0.08 0.16 0.24 80 150 22.1 0.08 1140
14 310 HB 0.3 2.7 0.08 0.16 0.24 70 140 22.1 0.08 1140
12 200 HB 0.3 3.3 0.08 0.21 0.38 170 250 22.1 0.09 2240
13 42 HRc 0.3 2.7 0.08 0.18 0.31 120 190 11.9 0.08 1180
15 150 HB 0.3 4.0 0.08 0.23 0.77 170 250 22.5 0.18 2240
15 200 HB 0.3 4.0 0.08 0.23 0.72 160 230 22.5 0.18 2220
16 250 HB 0.3 4.0 0.08 0.23 0.72 150 210 22.5 0.18 2200
17,19 150 HB 0.3 3.3 0.08 0.21 0.58 120 250 22.5 0.13 2240
17,19 200 HB 0.3 3.3 0.08 0.21 0.48 120 230 22.5 0.13 2220
18,20 250 HB 0.3 3.3 0.08 0.21 0.48 120 190 22.5 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.7 0.09 0.17 0.31 25 50 11.6 0.10 440
33 Inconel 700 250 HB 0.3 2.7 0.09 0.17 0.31 25 50 11.6 0.10 440
34 Stellite 21 350 HB 0.3 2.7 0.09 0.17 0.31 23 45 11.6 0.10 335
36 TiAl6V4 - 0.3 2.7 0.09 0.18 0.38 45 65 11.6 0.14 660
37 T40 - 0.3 2.7 0.09 0.16 0.31 35 60 11.6 0.10 550
38 45 HRc 0.3 2.4 0.05 0.14 0.24 50 100 11.8 0.10 990
38 50 HRc 0.3 2.0 0.05 0.12 0.20 40 90 11.4 0.08 880
38 55 HRc 0.3 1.9 0.05 0.10 0.16 40 80 11.1 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 2.1 0.05 0.14 0.20 40 60 11.4 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.9 0.05 0.10 0.16 30 50 11.1 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 5.3 0.10 0.35 0.84 200 400 2.5 0.23 350
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
SCMT 09T304 – LT 10 | LT 1000
SCMT
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
84
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 4.0 0.21 0.50 1.62 180 330 33.0 0.32 2240
2 190 HB 0.5 4.0 0.21 0.50 1.62 180 280 33.0 0.32 2220
3 250 HB 0.5 4.0 0.21 0.45 1.35 180 250 33.0 0.32 2200
6 180 HB 0.5 4.0 0.21 0.45 1.08 120 280 33.0 0.29 2200
4,6 230 HB 0.5 3.2 0.21 0.45 1.08 120 250 33.0 0.29 1180
5,7 280 HB 0.5 3.2 0.18 0.40 1.08 120 210 33.0 0.27 1150
8 350 HB 0.5 2.8 0.18 0.40 0.90 120 180 33.0 0.27 1130
10 220 HB 0.5 3.2 0.18 0.40 1.08 70 190 22.5 0.27 1140
10 280 HB 0.5 3.2 0.18 0.40 1.08 70 150 22.5 0.27 1120
11 320 HB 0.5 2.4 0.18 0.35 0.72 70 130 22.5 0.25 1100
11 350 HB 0.5 2.4 0.18 0.35 0.72 70 110 22.5 0.25 990
14 180 HB 0.5 4.0 0.20 0.40 1.08 170 270 33.0 0.32 2200
14 240 HB 0.5 4.0 0.20 0.40 0.90 160 220 33.0 0.29 1180
14 290 HB 0.5 3.2 0.18 0.35 0.72 80 150 22.5 0.25 1100
14 310 HB 0.5 3.2 0.18 0.35 0.72 70 140 22.5 0.25 990
12 200 HB 0.5 4.0 0.22 0.40 0.90 170 250 33.0 0.29 1190
13 42 HRc 0.5 3.2 0.22 0.40 0.90 120 190 22.5 0.29 1130
15 150 HB 0.5 4.0 0.15 0.60 1.80 170 250 33.0 0.32 2200
15 200 HB 0.5 4.0 0.15 0.60 1.62 160 230 33.0 0.32 1180
16 250 HB 0.5 4.0 0.15 0.55 1.62 150 210 33.0 0.32 1160
17,19 150 HB 0.5 4.0 0.15 0.50 1.35 120 250 33.0 0.27 1180
17,19 200 HB 0.5 4.0 0.15 0.50 1.17 120 230 33.0 0.27 1160
18,20 250 HB 0.5 4.0 0.15 0.50 1.08 120 190 33.0 0.27 1140
31,32 Incoloy 800 240 HB 0.5 2.4 0.20 0.35 0.63 25 45 22.0 0.25 332
33 Inconel 700 250 HB 0.5 2.4 0.20 0.35 0.63 25 45 22.0 0.25 330
34 Stellite 21 350 HB 0.5 2.4 0.20 0.35 0.63 23 40 22.0 0.25 228
36 TiAl6V4 - 0.5 3.2 0.20 0.40 0.72 45 65 22.0 0.30 555
37 T40 - 0.5 2.4 0.20 0.35 0.63 35 55 22.0 0.27 445
38 45 HRc 0.5 2.0 0.11 0.30 0.54 50 100 22.0 0.23 880
38 50 HRc 0.5 1.6 0.11 0.25 0.36 40 90 11.5 0.18 770
38 55 HRc 0.5 1.2 0.11 0.20 0.27 40 80 11.0 0.16 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.6 0.11 0.25 0.36 40 60 11.5 0.16 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.2 0.11 0.20 0.27 30 50 11.0 0.14 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.8 0.20 0.60 1.60 200 400 3.0 0.36 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
4304, 316,
X5CrNi18-9
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
7 GG20, GG40, EN-GJL-250,
No30B
10
8
SCMT 09T308 – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
85
TURNING
FProductivity
F M RInsert Designation s r Catalog Nr.l
LT 1005 Recommended for moderate to high speed
T00032401.204.7612SNMA 120412 LT 1005
T00032390.804.7612SNMA 120408 LT 1005
Application Guide
Strong edge preparation mainly for gray cast iron. For general purpose turning, facing and boring operations.
Fixing
S N Ml
Shape
90°m
Ø d0°
Clearance Angle Toleranced ± 0.08m ± 0.13s ± 0.13
s
SNMA
86
TURNING Machining Conditions
SNMA 120408 – LT 1005
SNMA 120412 – LT 1005
min max min max min max D.O.C. Feed
15 150 HB 0.7 6.0 0.20 0.60 1.7 270 450 33.5 00.40 3350
15 200 HB 0.7 6.0 0.20 0.58 1.5 200 320 33.5 00.40 2250
16 250 HB 0.7 6.0 0.20 0.56 1.5 170 240 33.5 00.40 2220
17,19 150 HB 0.7 6.0 0.20 0.52 1.3 130 260 33.0 00.30 2240
17,19 200 HB 0.7 6.0 0.20 0.50 1.1 130 230 33.0 00.30 2210
18,20 250 HB 0.7 6.0 0.20 0.48 1.0 130 190 33.0 00.30 1180
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.4 0.14 0.25 0.3 40 60 11.5 00.19 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.8 0.14 0.20 0.3 30 50 11.2 00.17 440
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
min max min max min max D.O.C. Feed
15 150 HB 0.7 6.0 0.20 0.40 1.4 270 450 33.5 00.32 3350
15 200 HB 0.7 6.0 0.20 0.38 1.2 200 320 33.5 00.32 2250
16 250 HB 0.7 6.0 0.20 0.36 1.2 170 240 33.5 00.32 2220
17,19 150 HB 0.7 6.0 0.20 0.40 1.0 130 260 22.5 00.30 2240
17,19 200 HB 0.7 6.0 0.20 0.38 0.9 130 230 22.5 00.30 2210
18,20 250 HB 0.7 6.0 0.20 0.36 0.8 130 190 22.5 00.30 1180
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.4 0.14 0.20 0.3 40 60 11.4 00.16 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.8 0.14 0.20 0.2 30 50 11.1 00.15 44011
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm]Feed
[mm/rev] Amax[mm2]
Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm]Feed
[mm/rev] Amax[mm2]
Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Cast
Iron
Grey
Malleable & Nodular
H
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Cast
Iron
Grey
Malleable & Nodular
H
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Cast
Iron
Grey
Malleable & Nodular
H
Chilled Cast Iron
White Cast Iron
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
87
TURNING
Stainless Steel
VC
NX-CNMP-TNMP-WNMP
Stainless SteelExotic Material Exotic Material
Cutting Conditions!Verify
FProductivity
S N M Gl
Shape
90°m
Ø d0°
Clearance Angle Fixing,Chipbreaker
ss
Toleranced ± 0.08m ± 0.13s ± 0.13
F M R
Application Guide
Insert Designation s r Catalog Nr.l
LT 10 Multi-MatTM General Usage – Standard
T00003231.204.7612SNMG 120412 NN LT 10
T00003220.804.7612SNMG 120408 NN LT 10
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00019221.204.7612SNMG 120412 NN LT 1000
T00030110.804.7612SNMG 120408 NX LT 1000
T00019210.804.7612SNMG 120408 NN LT 1000
LT 1000 Multi-MatTM General Usage – Premium
Square inserts with strong cutting edge. Suitable for roughing operations.
NN chipbreaker NX chipbreaker
SNMG
88
TURNING
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
SNMG 120408 NX LT 1025
SNMG 120412 NN LT 1025
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00040781.204.7612SNMG 120412 NN LT 1005
T00040770.804.7612SNMG 120408 NX LT 1005
T00040760.804.7612SNMG 120408 NN LT 1005
LT 1005 Recommended for moderate to high speed
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00041361.204.7612
T00041340.804.7612
T00041330.804.7612SNMG 120408 NN LT 1025
LT 1025 Recommended for moderate to low speed
S N M G
VC
Productivity NX-CNMP-TNMP-WNMP
Stainless SteelExotic Material
NN chipbreaker NX chipbreaker
LT 1005
89
TURNINGMachining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 5.0 0.30 0.70 2.54 180 330 33.0 0.50 2240
2 190 HB 0.5 5.0 0.30 0.70 2.54 180 280 33.0 0.50 2220
3 250 HB 0.5 5.0 0.30 0.63 2.12 180 250 33.0 0.50 2200
6 180 HB 0.5 5.0 0.30 0.63 1.69 120 280 33.0 0.45 2200
4,6 230 HB 0.5 4.0 0.30 0.63 1.69 120 250 33.0 0.45 1180
5,7 280 HB 0.5 4.0 0.25 0.56 1.69 120 210 33.0 0.43 1150
8 350 HB 0.5 3.5 0.25 0.56 1.41 120 180 33.0 0.43 1130
10 220 HB 0.5 4.0 0.25 0.56 1.69 70 190 22.5 0.43 1140
10 280 HB 0.5 4.0 0.25 0.56 1.69 70 150 22.5 0.43 1120
11 320 HB 0.5 3.0 0.25 0.49 1.13 70 130 22.5 0.40 1100
11 350 HB 0.5 3.0 0.25 0.49 1.13 70 110 22.5 0.40 990
14 180 HB 0.5 5.0 0.28 0.56 1.69 170 270 33.0 0.50 1190
14 240 HB 0.5 5.0 0.28 0.56 1.41 160 220 33.0 0.45 1170
14 290 HB 0.5 4.0 0.25 0.49 1.13 80 150 22.5 0.40 1100
14 310 HB 0.5 4.0 0.25 0.49 1.13 70 140 22.5 0.40 990
12 200 HB 0.5 5.0 0.31 0.56 1.41 170 250 33.0 0.45 1190
13 42 HRc 0.5 4.0 0.31 0.56 1.41 120 190 22.5 0.45 1130
15 150 HB 0.5 5.0 0.21 0.84 2.82 170 250 33.0 0.50 2200
15 200 HB 0.5 5.0 0.21 0.84 2.54 160 230 33.0 0.50 1180
16 250 HB 0.5 5.0 0.21 0.77 2.54 150 210 33.0 0.50 1160
17,19 150 HB 0.5 5.0 0.21 0.70 2.12 120 250 33.0 0.43 1180
17,19 200 HB 0.5 5.0 0.21 0.70 1.83 120 230 33.0 0.43 1160
18,20 250 HB 0.5 5.0 0.21 0.70 1.69 120 190 33.0 0.43 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.28 0.49 0.99 25 45 22.0 0.40 332
33 Inconel 700 250 HB 0.5 3.0 0.28 0.49 0.99 25 45 22.0 0.40 330
34 Stellite 21 350 HB 0.5 3.0 0.28 0.49 0.99 23 40 22.0 0.40 228
36 TiAl6V4 - 0.5 4.0 0.28 0.56 1.13 45 65 22.0 0.47 555
37 T40 - 0.5 3.0 0.28 0.49 0.99 35 55 22.0 0.43 445
38 45 HRc 0.5 2.5 0.16 0.42 0.85 50 100 22.0 0.36 880
38 50 HRc 0.5 2.0 0.16 0.35 0.56 40 90 11.5 0.28 770
38 55 HRc 0.5 1.5 0.16 0.28 0.42 40 80 11.0 0.26 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.16 0.35 0.56 40 60 11.5 0.26 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.16 0.28 0.42 30 50 11.0 0.21 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.28 0.80 2.50 200 400 3.0 0.57 280
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42
Har
dene
d M
at.
Steel
11
GGG40, GGG70, 50005
Hig
h Te
mp.
Allo
ys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cas
t Ir
on
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Sta
inle
ss S
teel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
Ste
el
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
SNMG 120408 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Values for lead angle (Kr)=45°; For lead angle (Kr)=75°, please limit feed to 75% of the recommended
90
TURNING Machining Conditions
SNMG 120408 NN – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.30 0.70 2.54 90 330 33.0 0.54 2240
2 190 HB 0.5 5.0 0.30 0.70 2.54 90 280 33.0 0.50 2220
3 250 HB 0.5 5.0 0.30 0.63 2.12 90 250 33.0 0.47 2200
6 180 HB 0.5 5.0 0.30 0.63 1.69 60 280 33.0 0.45 2200
4,6 230 HB 0.5 4.0 0.30 0.63 1.69 60 250 33.0 0.45 1180
5,7 280 HB 0.5 4.0 0.25 0.56 1.69 60 210 33.0 0.43 1150
8 350 HB 0.5 3.5 0.25 0.56 1.41 60 180 22.7 0.43 1130
10 220 HB 0.5 4.0 0.25 0.56 1.69 35 190 22.5 0.43 1140
10 280 HB 0.5 4.0 0.25 0.56 1.69 35 150 22.5 0.43 1120
11 320 HB 0.5 3.0 0.25 0.49 1.13 35 130 22.2 0.40 1100
11 350 HB 0.5 3.0 0.25 0.49 1.13 35 110 22.2 0.40 990
14 180 HB 0.5 5.0 0.28 0.56 1.69 85 270 33.0 0.36 1190
14 240 HB 0.5 5.0 0.28 0.56 1.41 80 220 33.0 0.31 1170
14 290 HB 0.5 4.0 0.25 0.49 1.13 40 150 22.5 0.34 1100
14 310 HB 0.5 4.0 0.25 0.49 1.13 35 140 22.5 0.34 990
12 200 HB 0.5 5.0 0.25 0.56 0.99 85 250 22.5 0.28 1190
13 42 HRc 0.5 4.0 0.25 0.56 0.99 60 190 22.2 0.28 1130
17,19 150 HB 0.5 5.0 0.21 0.70 2.12 60 250 33.0 0.43 1180
17,19 200 HB 0.5 5.0 0.21 0.70 1.83 60 230 33.0 0.43 1160
18,20 250 HB 0.5 5.0 0.21 0.70 1.69 60 190 33.0 0.43 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
SNMG 120408 NN – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.30 0.70 2.54 180 430 33.0 0.54 2265
2 190 HB 0.5 5.0 0.30 0.70 2.54 180 365 33.0 0.50 2240
3 250 HB 0.5 5.0 0.30 0.63 2.12 180 325 33.0 0.47 2220
6 180 HB 0.5 5.0 0.30 0.63 1.69 120 365 33.0 0.45 2220
4,6 230 HB 0.5 4.0 0.30 0.63 1.69 120 325 33.0 0.45 2200
5,7 280 HB 0.5 4.0 0.25 0.56 1.69 120 275 33.0 0.43 1165
8 350 HB 0.5 3.5 0.25 0.56 1.41 120 235 22.7 0.43 1145
10 220 HB 0.5 4.0 0.25 0.56 1.69 70 245 22.5 0.43 1155
10 280 HB 0.5 4.0 0.25 0.56 1.69 70 195 22.5 0.43 1130
11 320 HB 0.5 3.0 0.25 0.49 1.13 70 170 22.2 0.40 1110
11 350 HB 0.5 3.0 0.25 0.49 1.13 70 145 22.2 0.40 1100
15 150 HB 0.5 5.0 0.21 0.84 2.82 170 325 33.0 0.50 2220
15 200 HB 0.5 5.0 0.21 0.84 2.54 160 300 33.0 0.50 2200
16 250 HB 0.5 5.0 0.21 0.77 2.54 150 275 33.0 0.50 1175
17,19 150 HB 0.5 5.0 0.21 0.70 2.12 120 325 33.0 0.43 2200
17,19 200 HB 0.5 5.0 0.21 0.70 1.83 120 300 33.0 0.43 1175
18,20 250 HB 0.5 5.0 0.21 0.70 1.69 120 245 33.0 0.43 1155
38 45 HRc 0.5 2.5 0.16 0.42 0.85 50 130 22.0 0.36 990
38 50 HRc 0.5 2.0 0.16 0.35 0.56 40 115 11.5 0.28 775
38 55 HRc 0.5 1.5 0.16 0.28 0.42 40 105 11.0 0.26 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.16 0.35 0.56 40 80 11.5 0.26 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.16 0.28 0.42 30 65 11.0 0.21 445
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
7 GG20, GG40, EN-GJL-250,
No30B
8
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Values for lead angle (Kr)=45°; For lead angle (Kr)=75°, please limit feed to 75% of the recommended
Values for lead angle (Kr)=45°; For lead angle (Kr)=75°, please limit feed to 75% of the recommended
91
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.26 0.70 2.40 180 330 33.0 0.47 2240
2 190 HB 0.5 5.0 0.26 0.70 2.40 180 280 33.0 0.47 2220
3 250 HB 0.5 5.0 0.26 0.63 2.00 180 250 33.0 0.47 2200
6 180 HB 0.5 5.0 0.26 0.63 1.60 120 280 33.0 0.43 2200
4,6 230 HB 0.5 4.0 0.26 0.63 1.60 120 250 33.0 0.43 1180
5,7 280 HB 0.5 4.0 0.22 0.56 1.60 120 210 33.0 0.41 1150
8 350 HB 0.5 3.5 0.22 0.56 1.35 120 180 33.0 0.41 1130
10 220 HB 0.5 4.0 0.22 0.56 1.60 70 190 22.5 0.41 1140
10 280 HB 0.5 4.0 0.22 0.56 1.60 70 150 22.5 0.41 1120
11 320 HB 0.5 3.0 0.22 0.49 1.05 70 130 22.5 0.38 1100
11 350 HB 0.5 3.0 0.22 0.49 1.05 70 110 22.5 0.38 990
14 180 HB 0.5 5.0 0.25 0.56 1.60 170 270 33.0 0.34 1190
14 240 HB 0.5 5.0 0.25 0.56 1.35 160 220 33.0 0.30 1170
14 290 HB 0.5 4.0 0.22 0.49 1.05 80 150 22.5 0.38 1100
14 310 HB 0.5 4.0 0.22 0.49 1.05 70 140 22.5 0.38 990
12 200 HB 0.5 5.0 0.27 0.56 1.35 170 250 22.5 0.41 1190
13 42 HRc 0.5 4.0 0.27 0.56 1.35 120 190 22.5 0.34 1130
15 150 HB 0.5 5.0 0.18 0.84 2.70 170 250 33.0 0.47 2200
15 200 HB 0.5 5.0 0.18 0.84 2.40 160 230 33.0 0.47 1180
16 250 HB 0.5 5.0 0.18 0.77 2.40 150 210 33.0 0.47 1160
17,19 150 HB 0.5 5.0 0.18 0.70 2.00 120 250 33.0 0.41 1180
17,19 200 HB 0.5 5.0 0.18 0.70 1.75 120 230 33.0 0.41 1160
18,20 250 HB 0.5 5.0 0.18 0.70 1.60 120 190 33.0 0.41 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.25 0.49 0.95 25 45 22.0 0.38 330
33 Inconel 700 250 HB 0.5 3.0 0.25 0.49 0.95 25 45 22.0 0.38 330
34 Stellite 21 350 HB 0.5 3.0 0.25 0.49 0.95 25 40 22.0 0.38 330
36 TiAl6V4 - 0.5 4.0 0.25 0.56 1.05 45 65 22.0 0.45 555
37 T40 - 0.5 3.0 0.25 0.49 0.95 35 55 22.0 0.41 445
38 45 HRc 0.5 2.5 0.14 0.42 0.80 50 100 22.0 0.34 880
38 50 HRc 0.5 2.0 0.14 0.35 0.55 40 90 11.5 0.27 770
38 55 HRc 0.5 1.5 0.14 0.28 0.40 40 80 11.0 0.24 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.14 0.35 0.55 40 60 11.5 0.24 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.14 0.28 0.40 30 50 11.0 0.20 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.25 0.84 2.40 200 400 33.0 0.54 280
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
2
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
St
eel
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
SNMG 120408 NX – LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Values for lead angle (Kr)=45°; For lead angle (Kr)=75°, please limit feed to 75% of the recommended
92
TURNING Machining Conditions
SNMG 120408 NX – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.26 0.70 2.41 90 330 33.0 0.51 2240
2 190 HB 0.5 5.0 0.26 0.70 2.41 90 280 33.0 0.47 2220
3 250 HB 0.5 5.0 0.26 0.63 2.01 90 250 33.0 0.45 2200
6 180 HB 0.5 5.0 0.26 0.63 1.61 60 280 33.0 0.43 2200
4,6 230 HB 0.5 4.0 0.26 0.63 1.61 60 250 33.0 0.43 1180
5,7 280 HB 0.5 4.0 0.22 0.56 1.61 60 210 33.0 0.41 1150
8 350 HB 0.5 3.5 0.22 0.56 1.34 60 180 22.7 0.41 1130
10 220 HB 0.5 4.0 0.22 0.56 1.61 35 190 22.5 0.41 1140
10 280 HB 0.5 4.0 0.22 0.56 1.61 35 150 22.5 0.41 1120
11 320 HB 0.5 3.0 0.22 0.49 1.07 35 130 22.2 0.38 1100
11 350 HB 0.5 3.0 0.22 0.49 1.07 35 110 22.2 0.38 990
14 180 HB 0.5 5.0 0.25 0.56 1.61 85 270 33.0 0.34 1190
14 240 HB 0.5 5.0 0.25 0.56 1.34 80 220 33.0 0.30 1170
14 290 HB 0.5 4.0 0.22 0.49 1.07 40 150 22.5 0.32 1100
14 310 HB 0.5 4.0 0.22 0.49 1.07 35 140 22.5 0.32 990
12 200 HB 0.5 5.0 0.22 0.56 0.94 85 250 22.5 0.27 1190
13 42 HRc 0.5 4.0 0.22 0.56 0.94 60 190 22.2 0.27 1130
17,19 150 HB 0.5 5.0 0.18 0.70 2.01 60 250 33.0 0.41 1180
17,19 200 HB 0.5 5.0 0.18 0.70 1.74 60 230 33.0 0.41 1160
18,20 250 HB 0.5 5.0 0.18 0.70 1.61 60 190 33.0 0.41 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
SNMG 120408 NX – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.26 0.70 2.41 180 430 33.0 0.51 2265
2 190 HB 0.5 5.0 0.26 0.70 2.41 180 365 33.0 0.47 2240
3 250 HB 0.5 5.0 0.26 0.63 2.01 180 325 33.0 0.45 2220
6 180 HB 0.5 5.0 0.26 0.63 1.61 120 365 33.0 0.43 2220
4,6 230 HB 0.5 4.0 0.26 0.63 1.61 120 325 33.0 0.43 2200
5,7 280 HB 0.5 4.0 0.22 0.56 1.61 120 275 33.0 0.41 1165
8 350 HB 0.5 3.5 0.22 0.56 1.34 120 235 22.7 0.41 1145
10 220 HB 0.5 4.0 0.22 0.56 1.61 70 245 22.5 0.41 1155
10 280 HB 0.5 4.0 0.22 0.56 1.61 70 195 22.5 0.41 1130
11 320 HB 0.5 3.0 0.22 0.49 1.07 70 170 22.2 0.38 1110
11 350 HB 0.5 3.0 0.22 0.49 1.07 70 145 22.2 0.38 1100
15 150 HB 0.5 5.0 0.18 0.84 2.68 170 325 33.0 0.47 2220
15 200 HB 0.5 5.0 0.18 0.84 2.41 160 300 33.0 0.47 2200
16 250 HB 0.5 5.0 0.18 0.77 2.41 150 275 33.0 0.47 1175
17,19 150 HB 0.5 5.0 0.18 0.70 2.01 120 325 33.0 0.41 2200
17,19 200 HB 0.5 5.0 0.18 0.70 1.74 120 300 33.0 0.41 1175
18,20 250 HB 0.5 5.0 0.18 0.70 1.61 120 245 33.0 0.41 1155
38 45 HRc 0.5 2.5 0.14 0.42 0.80 50 130 22.0 0.34 990
38 50 HRc 0.5 2.0 0.14 0.35 0.54 40 115 11.5 0.27 775
38 55 HRc 0.5 1.5 0.14 0.28 0.40 40 105 11.0 0.24 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.14 0.35 0.54 40 80 11.5 0.24 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.14 0.28 0.40 30 65 11.0 0.20 445
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Values for lead angle (Kr)=45°; For lead angle (Kr)=75°, please limit feed to 75% of the recommended
Values for lead angle (Kr)=45°; For lead angle (Kr)=75°, please limit feed to 75% of the recommended
93
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.7 6.0 0.37 0.95 3.96 180 330 44.0 0.65 2240
2 190 HB 0.7 6.0 0.37 0.95 3.96 180 280 44.0 0.65 2220
3 250 HB 0.7 6.0 0.37 0.86 3.30 180 250 44.0 0.65 2200
6 180 HB 0.7 6.0 0.37 0.86 2.64 120 280 44.0 0.60 2200
4,6 230 HB 0.7 4.8 0.37 0.86 2.64 120 250 44.0 0.60 1180
5,7 280 HB 0.7 4.8 0.32 0.76 2.64 120 210 44.0 0.56 1150
8 350 HB 0.7 4.2 0.32 0.76 2.40 120 180 44.0 0.56 1130
10 220 HB 0.7 4.8 0.32 0.76 2.64 70 190 33.4 0.56 1140
10 280 HB 0.7 4.8 0.32 0.76 2.64 70 150 33.4 0.56 1120
11 320 HB 0.7 3.6 0.32 0.67 1.76 70 130 33.4 0.52 1100
11 350 HB 0.7 3.6 0.32 0.67 1.76 70 110 33.4 0.52 990
14 180 HB 0.7 6.0 0.35 0.76 2.64 170 270 44.0 0.58 1190
14 240 HB 0.7 6.0 0.35 0.76 2.20 160 220 44.0 0.52 1170
14 290 HB 0.7 4.8 0.32 0.67 1.76 80 150 33.4 0.46 1100
14 310 HB 0.7 4.8 0.32 0.67 1.76 70 140 33.4 0.46 990
12 200 HB 0.7 6.0 0.39 0.76 2.20 170 250 44.0 0.55 1190
13 42 HRc 0.7 4.8 0.39 0.76 2.20 120 190 33.0 0.50 1130
15 150 HB 0.7 6.0 0.30 1.14 4.40 170 250 44.0 0.65 2200
15 200 HB 0.7 6.0 0.30 1.14 3.96 160 230 44.0 0.65 1180
16 250 HB 0.7 6.0 0.30 1.05 3.96 150 210 44.0 0.65 1160
17,19 150 HB 0.7 6.0 0.30 0.95 3.30 120 250 44.0 0.56 1180
17,19 200 HB 0.7 6.0 0.30 0.95 2.86 120 230 44.0 0.56 1160
18,20 250 HB 0.7 6.0 0.30 0.95 2.64 120 190 44.0 0.56 1140
31,32 Incoloy 800 240 HB 0.7 3.6 0.35 0.67 1.54 25 45 22.7 0.52 332
33 Inconel 700 250 HB 0.7 3.6 0.35 0.67 1.54 25 45 22.7 0.52 330
34 Stellite 21 350 HB 0.7 3.6 0.35 0.67 1.54 23 40 22.7 0.52 228
36 TiAl6V4 - 0.7 4.8 0.35 0.76 1.76 45 65 22.7 0.58 555
37 T40 - 0.7 3.6 0.35 0.67 1.54 35 55 22.7 0.52 445
38 45 HRc 0.7 3.0 0.19 0.57 1.32 50 100 22.7 0.47 880
38 50 HRc 0.7 2.4 0.19 0.48 0.88 40 90 22.0 0.37 770
38 55 HRc 0.7 1.8 0.19 0.38 0.66 40 80 11.3 0.33 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.4 0.19 0.48 0.88 40 60 22.0 0.33 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.8 0.19 0.38 0.66 30 50 11.3 0.28 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.7 7.0 0.35 1.14 4.30 200 400 4.0 0.80 280
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Ste
el
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
SNMG 120412 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Values for lead angle (Kr)=45°; For lead angle (Kr)=75°, please limit feed to 75% of the recommended
94
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.7 6.0 0.37 0.95 3.96 90 330 44.0 00.71 2240
2 190 HB 0.7 6.0 0.37 0.95 3.96 90 280 44.0 00.65 2220
3 250 HB 0.7 6.0 0.37 0.86 3.30 90 250 44.0 00.61 2200
6 180 HB 0.7 6.0 0.37 0.86 2.64 60 280 44.0 00.60 2200
4,6 230 HB 0.7 4.8 0.37 0.86 2.64 60 250 44.0 00.60 1180
5,7 280 HB 0.7 4.8 0.32 0.76 2.64 60 210 44.0 00.56 1150
8 350 HB 0.7 4.2 0.32 0.76 2.20 60 180 33.6 00.56 1130
10 220 HB 0.7 4.8 0.32 0.76 2.64 35 190 33.4 00.56 1140
10 280 HB 0.7 4.8 0.32 0.76 2.64 35 150 33.4 00.56 1120
11 320 HB 0.7 3.6 0.32 0.67 1.76 35 130 22.9 00.52 1100
11 350 HB 0.7 3.6 0.32 0.67 1.76 35 110 22.9 00.52 990
14 180 HB 0.7 6.0 0.35 0.76 2.64 85 270 44.0 00.47 1190
14 240 HB 0.7 6.0 0.35 0.76 2.20 80 220 44.0 00.41 1170
14 290 HB 0.7 4.8 0.32 0.67 1.76 40 150 33.4 00.45 1100
14 310 HB 0.7 4.8 0.32 0.67 1.76 35 140 33.4 00.45 990
12 200 HB 0.7 6.0 0.32 0.76 1.54 85 250 33.4 00.37 1190
13 42 HRc 0.7 4.8 0.32 0.76 1.54 60 190 22.9 00.37 1130
17,19 150 HB 0.7 6.0 0.26 0.95 3.30 60 250 44.0 00.56 1180
17,19 200 HB 0.7 6.0 0.26 0.95 2.86 60 230 44.0 00.56 1160
18,20 250 HB 0.7 6.0 0.26 0.95 2.64 60 190 44.0 00.56 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
SNMG 120412 NN – LT 1025
SNMG 120412 NN – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.7 6.0 0.37 0.95 3.96 180 430 44.0 00.71 2265
2 190 HB 0.7 6.0 0.37 0.95 3.96 180 365 44.0 00.65 2240
3 250 HB 0.7 6.0 0.37 0.86 3.30 180 325 44.0 00.61 2220
6 180 HB 0.7 6.0 0.37 0.86 2.64 120 365 44.0 00.60 2220
4,6 230 HB 0.7 4.8 0.37 0.86 2.64 120 325 44.0 00.60 2200
5,7 280 HB 0.7 4.8 0.32 0.76 2.64 120 275 44.0 00.56 1165
8 350 HB 0.7 4.2 0.32 0.76 2.20 120 235 33.6 00.56 1145
10 220 HB 0.7 4.8 0.32 0.76 2.64 70 245 33.4 00.56 1155
10 280 HB 0.7 4.8 0.32 0.76 2.64 70 195 33.4 00.56 1130
11 320 HB 0.7 3.6 0.32 0.67 1.76 70 170 22.9 00.52 1110
11 350 HB 0.7 3.6 0.32 0.67 1.76 70 145 22.9 00.52 1100
15 150 HB 0.7 6.0 0.26 1.14 4.40 170 325 44.0 00.65 2220
15 200 HB 0.7 6.0 0.26 1.14 3.96 160 300 44.0 00.65 2200
16 250 HB 0.7 6.0 0.26 1.05 3.96 150 275 44.0 00.65 1175
17,19 150 HB 0.7 6.0 0.26 0.95 3.30 120 325 44.0 00.56 2200
17,19 200 HB 0.7 6.0 0.26 0.95 2.86 120 300 44.0 00.56 1175
18,20 250 HB 0.7 6.0 0.26 0.95 2.64 120 245 44.0 00.56 1155
38 45 HRc 0.7 3.0 0.19 0.57 1.32 50 130 22.7 00.47 990
38 50 HRc 0.7 2.4 0.19 0.48 0.88 40 115 22.0 00.37 775
38 55 HRc 0.7 1.8 0.19 0.38 0.66 40 105 11.3 00.33 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.4 0.19 0.48 0.88 40 80 22.0 00.33 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.8 0.19 0.38 0.66 30 65 11.3 00.28 445
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
7 GG20, GG40, EN-GJL-250,
No30B
8
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Values for lead angle (Kr)=45°; For lead angle (Kr)=75°, please limit feed to 75% of the recommended
Values for lead angle (Kr)=45°; For lead angle (Kr)=75°, please limit feed to 75% of the recommended
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
95
TURNING
Stainless Steel
VC
T C M T7°
Shape Clearance Angle Toleranced ± 0.05m ± 0.08s ± 0.13
l
m
Ø d
Fixing,Chipbreaker
60°
s
F M RInsert Designation s r Catalog Nr.l
LT 10 Multi-MatTM General Usage – Standard
T00017741.203.9716TCMT 16T312 NN LT 10
T00000680.803.9716TCMT 16T308 NN LT 10
T00004790.403.9716TCMT 16T304 NN LT 10
T00004780.802.3811TCMT 110208 NN LT 10
T00004770.402.3811TCMT 110204 NN LT 10
F M
Application Guide
Insert Designation s r Catalog Nr.l
T00019291.203.9716TCMT 16T312 NN LT 1000
T00019280.803.9716TCMT 16T308 NN LT 1000
T00019270.403.9716TCMT 16T304 NN LT 1000
T00019250.802.3811TCMT 110208 NN LT 1000
T00019240.402.3811TCMT 110204 NN LT 1000
R
LT 1000 Multi-MatTM General Usage – Premium
60
60° triangle shape inserts with positive rake angle. Suitable for boring and internal turning operations.
TCMT
Application Guide
96
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.3 2.1 0.08 0.20 0.37 180 330 11.0 0.14 3300
2 190 HB 0.3 1.8 0.08 0.19 0.32 180 280 11.0 0.14 2260
3 250 HB 0.3 1.8 0.08 0.17 0.30 180 250 11.0 0.14 2240
6 180 HB 0.3 1.8 0.08 0.17 0.31 120 280 11.0 0.11 2260
4,6 230 HB 0.3 1.8 0.08 0.17 0.30 120 250 11.0 0.11 2240
5,7 280 HB 0.3 1.4 0.08 0.15 0.25 120 210 11.0 0.10 2200
8 350 HB 0.3 1.4 0.08 0.15 0.22 120 180 11.0 0.10 1180
10 220 HB 0.3 1.8 0.07 0.15 0.25 70 190 00.9 0.08 1180
10 280 HB 0.3 1.8 0.07 0.14 0.25 70 150 00.9 0.08 1140
11 320 HB 0.3 1.4 0.07 0.12 0.20 70 130 00.9 0.08 1120
11 350 HB 0.3 1.4 0.07 0.12 0.16 70 110 00.9 0.08 1110
14 180 HB 0.3 1.8 0.06 0.15 0.20 170 270 11.0 0.07 2260
14 240 HB 0.3 1.8 0.06 0.15 0.16 160 220 11.0 0.06 2210
14 290 HB 0.3 1.4 0.06 0.12 0.12 80 150 00.9 0.06 1140
14 310 HB 0.3 1.4 0.06 0.12 0.12 70 140 00.9 0.06 1140
12 200 HB 0.3 1.8 0.06 0.15 0.20 170 250 00.9 0.07 2240
13 42 HRc 0.3 1.4 0.06 0.14 0.16 120 190 00.8 0.06 1180
15 150 HB 0.3 2.1 0.06 0.17 0.40 170 250 11.0 0.14 2240
15 200 HB 0.3 2.1 0.06 0.17 0.37 160 230 11.0 0.14 2220
16 250 HB 0.3 2.1 0.06 0.17 0.37 150 210 11.0 0.14 2200
17,19 150 HB 0.3 1.8 0.06 0.15 0.30 120 250 11.0 0.10 2240
17,19 200 HB 0.3 1.8 0.06 0.15 0.25 120 230 11.0 0.10 2220
18,20 250 HB 0.3 1.8 0.06 0.15 0.25 120 190 11.0 0.10 1180
31,32 Incoloy 800 240 HB 0.3 1.4 0.07 0.13 0.16 25 50 00.7 0.08 440
33 Inconel 700 250 HB 0.3 1.4 0.07 0.13 0.16 25 50 00.7 0.08 440
34 Stellite 21 350 HB 0.3 1.4 0.07 0.13 0.16 23 45 00.7 0.08 335
36 TiAl6V4 - 0.3 1.4 0.07 0.14 0.20 45 65 00.7 0.11 660
37 T40 - 0.3 1.4 0.07 0.12 0.16 35 60 00.7 0.08 550
38 45 HRc 0.3 1.3 0.04 0.10 0.12 50 100 00.7 0.08 990
38 50 HRc 0.3 1.1 0.04 0.09 0.11 40 90 00.6 0.06 880
38 55 HRc 0.3 1.0 0.04 0.08 0.08 40 80 00.5 0.05 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.1 0.04 0.10 0.11 40 60 00.6 0.08 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.0 0.04 0.08 0.08 30 50 00.5 0.05 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 2.8 0.08 0.26 0.43 200 400 1.0 0.18 350
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
TCMT 110204 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
97
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.2 2.1 0.08 0.20 0.37 180 330 11.0 0.25 3300
2 190 HB 0.2 1.8 0.08 0.19 0.32 180 280 11.0 0.25 2260
3 250 HB 0.2 1.8 0.08 0.17 0.30 180 250 11.0 0.25 2240
6 180 HB 0.2 1.8 0.08 0.17 0.31 120 280 11.0 0.21 2260
4,6 230 HB 0.2 1.8 0.08 0.17 0.30 120 250 11.0 0.21 2240
5,7 280 HB 0.2 1.4 0.08 0.15 0.25 120 210 11.0 0.21 2200
8 350 HB 0.2 1.4 0.08 0.15 0.22 120 180 11.0 0.21 1180
10 220 HB 0.2 1.8 0.07 0.15 0.25 70 190 11.0 0.17 1180
10 280 HB 0.2 1.8 0.07 0.14 0.25 70 150 11.0 0.17 1140
11 320 HB 0.2 1.4 0.07 0.12 0.20 70 130 11.0 0.17 1120
11 350 HB 0.2 1.4 0.07 0.12 0.16 70 110 11.0 0.17 1110
14 180 HB 0.2 1.8 0.08 0.15 0.20 170 270 11.0 0.17 2260
14 240 HB 0.2 1.8 0.08 0.15 0.16 160 220 11.0 0.17 2210
14 290 HB 0.2 1.4 0.07 0.12 0.12 80 150 11.0 0.17 1140
14 310 HB 0.2 1.4 0.07 0.12 0.12 70 140 11.0 0.17 1140
12 200 HB 0.2 1.8 0.08 0.15 0.20 170 250 11.0 0.21 2240
13 42 HRc 0.2 1.4 0.08 0.14 0.16 120 190 11.0 0.17 1180
15 150 HB 0.2 2.1 0.06 0.17 0.40 170 250 11.0 0.25 2240
15 200 HB 0.2 2.1 0.06 0.17 0.37 160 230 11.0 0.25 2220
16 250 HB 0.2 2.1 0.06 0.17 0.37 150 210 11.0 0.25 2200
17,19 150 HB 0.2 1.8 0.06 0.15 0.30 120 250 11.0 0.21 2240
17,19 200 HB 0.2 1.8 0.06 0.15 0.25 120 230 11.0 0.21 2220
18,20 250 HB 0.2 1.8 0.06 0.15 0.25 120 190 11.0 0.21 1180
31,32 Incoloy 800 240 HB 0.2 1.4 0.08 0.13 0.16 25 50 11.0 0.17 440
33 Inconel 700 250 HB 0.2 1.4 0.08 0.13 0.16 25 50 11.0 0.17 440
34 Stellite 21 350 HB 0.2 1.4 0.08 0.13 0.16 23 45 11.0 0.17 335
36 TiAl6V4 - 0.2 1.4 0.08 0.14 0.20 45 65 11.0 0.20 660
37 T40 - 0.2 1.4 0.08 0.12 0.16 35 60 11.0 0.17 550
38 45 HRc 0.2 1.3 0.04 0.10 0.12 50 100 00.8 0.15 990
38 50 HRc 0.2 1.1 0.04 0.09 0.11 40 90 00.6 0.13 880
38 55 HRc 0.2 1.0 0.04 0.08 0.08 40 80 00.5 0.10 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.2 1.1 0.04 0.10 0.11 40 60 00.6 0.15 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.2 1.0 0.04 0.08 0.08 30 50 00.5 0.10 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.2 2.8 0.08 0.26 0.43 200 400 11.0 0.28 350
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
TCMT 110208 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
98
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300
2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260
3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240
6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260
4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240
5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200
8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180
10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180
10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140
11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120
11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110
14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260
14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210
14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140
14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140
12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240
13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180
15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240
15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220
16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200
17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240
17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220
18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335
36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660
37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550
38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990
38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880
38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 00.9 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
TCMT 16T304 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
99
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.43 1.62 180 330 33.0 0.30 2240
2 190 HB 0.5 5.0 0.21 0.43 1.62 180 280 33.0 0.30 2220
3 250 HB 0.5 5.0 0.21 0.38 1.35 180 250 33.0 0.30 2200
6 180 HB 0.5 5.0 0.21 0.38 1.08 120 280 33.0 0.27 2200
4,6 230 HB 0.5 4.0 0.21 0.38 1.08 120 250 33.0 0.27 1180
5,7 280 HB 0.5 4.0 0.18 0.34 1.08 120 210 33.0 0.26 1150
8 350 HB 0.5 3.5 0.18 0.34 0.90 120 180 33.0 0.26 1130
10 220 HB 0.5 4.0 0.18 0.34 1.08 70 190 22.5 0.26 1140
10 280 HB 0.5 4.0 0.18 0.34 1.08 70 150 22.5 0.26 1120
11 320 HB 0.5 3.0 0.18 0.30 0.72 70 130 22.5 0.24 1100
11 350 HB 0.5 3.0 0.18 0.30 0.72 70 110 22.5 0.24 990
14 180 HB 0.5 5.0 0.20 0.34 1.08 170 270 33.0 0.30 2200
14 240 HB 0.5 5.0 0.20 0.34 0.90 160 220 33.0 0.27 1180
14 290 HB 0.5 4.0 0.18 0.30 0.72 80 150 22.5 0.24 1100
14 310 HB 0.5 4.0 0.18 0.30 0.72 70 140 22.5 0.24 990
12 200 HB 0.5 5.0 0.22 0.34 0.90 170 250 33.0 0.27 1190
13 42 HRc 0.5 4.0 0.22 0.34 0.90 120 190 22.5 0.27 1130
15 150 HB 0.5 5.0 0.15 0.51 1.80 170 250 33.0 0.30 2200
15 200 HB 0.5 5.0 0.15 0.51 1.62 160 230 33.0 0.30 1180
16 250 HB 0.5 5.0 0.15 0.47 1.62 150 210 33.0 0.30 1160
17,19 150 HB 0.5 5.0 0.15 0.43 1.35 120 250 33.0 0.26 1180
17,19 200 HB 0.5 5.0 0.15 0.43 1.17 120 230 33.0 0.26 1160
18,20 250 HB 0.5 5.0 0.15 0.43 1.08 120 190 33.0 0.26 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.30 0.63 25 45 22.0 0.24 332
33 Inconel 700 250 HB 0.5 3.0 0.20 0.30 0.63 25 45 22.0 0.24 330
34 Stellite 21 350 HB 0.5 3.0 0.20 0.30 0.63 23 40 22.0 0.24 228
36 TiAl6V4 - 0.5 4.0 0.20 0.34 0.72 45 65 22.0 0.28 555
37 T40 - 0.5 3.0 0.20 0.30 0.63 35 55 22.0 0.26 445
38 45 HRc 0.5 2.5 0.11 0.26 0.54 50 100 22.0 0.21 880
38 50 HRc 0.5 2.0 0.11 0.21 0.36 40 90 11.5 0.17 770
38 55 HRc 0.5 1.5 0.11 0.17 0.27 40 80 11.0 0.15 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.21 0.36 40 60 11.5 0.15 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.17 0.27 30 50 11.0 0.13 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.51 1.60 200 400 33.0 0.34 280
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
10
8
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Austenitic 4304, 316,
X5CrNi18-9
Duplex
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
1C35, Ck45, 1020, 1045, 1060, 28Mn6
Non-alloyed
Low alloyed
TCMT 16T308 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
100
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.48 1.94 180 330 33.0 0.38 2240
2 190 HB 0.5 5.0 0.21 0.48 1.94 180 280 33.0 0.38 2220
3 250 HB 0.5 5.0 0.21 0.43 1.62 180 250 33.0 0.38 2200
6 180 HB 0.5 5.0 0.21 0.43 1.30 120 280 33.0 0.35 2200
4,6 230 HB 0.5 4.0 0.21 0.43 1.30 120 250 33.0 0.35 1180
5,7 280 HB 0.5 4.0 0.18 0.38 1.30 120 210 33.0 0.32 1150
8 350 HB 0.5 3.5 0.18 0.38 1.08 120 180 33.0 0.32 1130
10 220 HB 0.5 4.0 0.18 0.38 1.30 70 190 22.5 0.32 1140
10 280 HB 0.5 4.0 0.18 0.38 1.30 70 150 22.5 0.32 1120
11 320 HB 0.5 3.0 0.18 0.33 0.86 70 130 22.5 0.30 1100
11 350 HB 0.5 3.0 0.18 0.33 0.86 70 110 22.5 0.30 990
14 180 HB 0.5 5.0 0.20 0.38 1.30 170 270 33.0 0.38 2200
14 240 HB 0.5 5.0 0.20 0.38 1.08 160 220 33.0 0.35 1180
14 290 HB 0.5 4.0 0.18 0.33 0.86 80 150 22.5 0.30 1100
14 310 HB 0.5 4.0 0.18 0.33 0.86 70 140 22.5 0.30 990
12 200 HB 0.5 5.0 0.22 0.38 1.08 170 250 33.0 0.35 1190
13 42 HRc 0.5 4.0 0.22 0.38 1.08 120 190 22.5 0.35 1130
15 150 HB 0.5 5.0 0.15 0.57 2.16 170 250 33.0 0.38 2200
15 200 HB 0.5 5.0 0.15 0.57 1.94 160 230 33.0 0.38 1180
16 250 HB 0.5 5.0 0.15 0.52 1.94 150 210 33.0 0.38 1160
17,19 150 HB 0.5 5.0 0.15 0.48 1.62 120 250 33.0 0.32 1180
17,19 200 HB 0.5 5.0 0.15 0.48 1.40 120 230 33.0 0.32 1160
18,20 250 HB 0.5 5.0 0.15 0.48 1.30 120 190 33.0 0.32 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.33 0.76 25 45 22.0 0.30 332
33 Inconel 700 250 HB 0.5 3.0 0.20 0.33 0.76 25 45 22.0 0.30 330
34 Stellite 21 350 HB 0.5 3.0 0.20 0.33 0.76 23 40 22.0 0.30 228
36 TiAl6V4 - 0.5 4.0 0.20 0.38 0.86 45 65 22.0 0.36 555
37 T40 - 0.5 3.0 0.20 0.33 0.76 35 55 22.0 0.32 445
38 45 HRc 0.5 2.5 0.11 0.29 0.65 50 100 22.0 0.27 880
38 50 HRc 0.5 2.0 0.11 0.24 0.43 40 90 11.5 0.22 770
38 55 HRc 0.5 1.5 0.11 0.19 0.32 40 80 11.0 0.19 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.24 0.43 40 60 11.5 0.19 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.19 0.32 30 50 11.0 0.16 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.57 1.90 200 400 33.0 0.43 280
Non-alloyed
Low alloyed
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Austenitic 4304, 316,
X5CrNi18-9
Duplex
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
10
8
TCMT 16T312 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
101
TURNING
FProductivity
F M RInsert Designation s r Catalog Nr.l
LT 1005 Recommended for moderate to high speed
T00032381.204.7616TNMA 160412 LT 1005
Strong edge preparation mainly for gray cast iron. For general purpose turning, facing and boring opera-tions.
T00028370.804.7616TNMA 160408 LT 1005
Shape Tolerance
0°
Clearance Angle Fixing, Chipbreaker
l
m
Ø d60°
s ± 0.13For l = 16, d ± 0.05 m ± 0.08 For l = 22, d ± 0.08 m ± 0.13
s
Application Guide
TNMA
102
TURNING Machining Conditions
TNMA 160408 – LT 1005
TNMA 160412 – LT 1005
min max min max min max D.O.C. Feed
15 150 HB 0.7 5.0 0.15 0.38 1.3 270 450 33.5 00.33 3350
15 200 HB 0.7 5.0 0.15 0.35 1.2 200 320 33.5 00.33 2250
16 250 HB 0.7 5.0 0.15 0.32 1.2 170 240 33.5 00.33 2220
17,19 150 HB 0.7 5.0 0.15 0.38 1.3 130 260 22.5 00.30 2240
17,19 200 HB 0.7 5.0 0.15 0.35 1.2 130 230 22.5 00.30 2210
18,20 250 HB 0.7 5.0 0.15 0.32 1.2 130 190 22.5 00.30 1180
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.0 0.11 0.20 0.3 40 60 11.4 00.16 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.5 0.11 0.20 0.2 30 50 11.0 00.15 44011
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
min max min max min max D.O.C. Feed
15 150 HB 0.7 5.0 0.15 0.35 1.3 270 450 33.2 00.30 3350
15 200 HB 0.7 5.0 0.15 0.33 1.2 200 320 33.2 00.30 2250
16 250 HB 0.7 5.0 0.15 0.30 1.2 170 240 33.2 00.30 2220
17,19 150 HB 0.7 5.0 0.15 0.35 1.0 130 260 22.5 00.28 2240
17,19 200 HB 0.7 5.0 0.15 0.33 0.9 130 230 22.5 00.28 2210
18,20 250 HB 0.7 5.0 0.15 0.30 0.8 130 190 22.5 00.28 1180
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.0 0.11 0.18 0.3 40 60 11.4 00.15 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.5 0.11 0.18 0.2 30 50 11.0 00.15 44011
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm]Feed
[mm/rev] Amax[mm2]
Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm]Feed
[mm/rev] Amax[mm2]
Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Cast
Iron
Grey
Malleable & Nodular
H
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Cast
Iron
Grey
Malleable & Nodular
H
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Cast
Iron
Grey
Malleable & Nodular
H
Chilled Cast Iron
White Cast Iron
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
103
TURNING
T N M G
Shape Tolerance
0°
Clearance Angle Fixing,Chipbreaker
l
m
Ø d60°
s ± 0.13For l = 16, d ± 0.05 m ± 0.08 For l = 22, d ± 0.08 m ± 0.13
ss
60°
60° triangle shape inserts. Suitable for general purpose turning and copying operations.
LT 10 and LT 1000
NX LT 10 and LT 1000 NX LT 10 and LT 1000
LT 10 and LT 1000
NX-CNMP-TNMP-WNMP
Stainless SteelExotic Material Exotic Material
Cutting Conditions!Verify
FProductivity
Stainless Steel
VC
F M RInsert Designation s r Catalog Nr.l
LT 10 Multi-MatTM General Usage – Standard
T00017351.204.7622TNMG 220412 NN LT 10
T00001130.804.7622TNMG 220408 NN LT 10
T00018730.404.7622TNMG 220404 NN LT 10
T00017341.204.7616TNMG 160412 NN LT 10
T00000690.804.7616TNMG 160408 NN LT 10
T00004570.404.7616TNMG 160404 NN LT 10
Application Guide
F M RInsert Designation s r Catalog Nr.l
LT 1000 Multi-MatTM General Usage – Premium
T00019361.204.7622TNMG 220412 NN LT 1000
T00030130.804.7622TNMG 220408 NX LT 1000
T00019350.804.7622TNMG 220408 NN LT 1000
T00019340.404.7622TNMG 220404 NN LT 1000
T00019331.204.7616TNMG 160412 NN LT 1000
T00030120.804.7616TNMG 160408 NX LT 1000
T00019320.804.7616TNMG 160408 NN LT 1000
T00019310.404.7616TNMG 160404 NN LT 1000
Application Guide TNMGTNMG
104
TURNING
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
F M RInsert Designation s r Catalog Nr.l
LT 1025 Recommended for moderate to low speed
T00041441.204.7622TNMG 220412 NN LT 1025
T00041430.804.7622TNMG 220408 NX LT 1025
T00041420.804.7622TNMG 220408 NN LT 1025
T00041401.204.7616TNMG 160412 NN LT 1025
T00041390.804.7616TNMG 160408 NX LT 1025
T00041380.804.7616TNMG 160408 NN LT 1025
Application Guide
F M RInsert Designation s r Catalog Nr.l
LT 1005 Recommended for moderate to high speed
T00040881.204.7622TNMG 220412 NN LT 1005
T00040870.804.7622TNMG 220408 NX LT 1005
T00040860.804.7622TNMG 220408 NN LT 1005
T00040841.204.7616TNMG 160412 NN LT 1005
T00040830.804.7616TNMG 160408 NX LT 1005
T00040820.804.7616TNMG 160408 NN LT 1005
Application Guide
T N M G
NX for LT 1025 LT 1005
NX-CNMP-TNMP-WNMP
Stainless SteelExotic Material VC
Productivity
NX chipbreaker NM chipbreaker
105
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300
2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260
3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240
6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260
4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240
5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200
8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180
10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180
10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140
11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120
11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110
14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260
14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210
14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140
14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140
12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240
13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180
15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240
15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220
16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200
17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240
17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220
18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335
36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660
37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550
38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990
38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880
38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 00.9 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
TNMG 160404 NN – T 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
106
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240
2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220
3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200
6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150
8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130
10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140
10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120
11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100
11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990
14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190
14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170
14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100
14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990
12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190
13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130
15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200
15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180
16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332
33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330
34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228
36 TiAl6V4 - 0.5 4.0 0.20 0.40 0.80 45 65 22.0 0.33 555
37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445
38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880
38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770
38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.25 0.40 40 60 11.5 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.20 0.30 30 50 11.0 0.15 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 3.0 0.40 280
Non-alloyed
Low alloyed
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Austenitic 4304, 316,
X5CrNi18-9
Duplex
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
10
8
TNMG 160408 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
107
TURNINGMachining Conditions
TNMG 160408 NN – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.50 1.80 90 330 33.0 0.38 2240
2 190 HB 0.5 5.0 0.21 0.50 1.80 90 280 33.0 0.35 2220
3 250 HB 0.5 5.0 0.21 0.45 1.50 90 250 33.0 0.33 2200
6 180 HB 0.5 5.0 0.21 0.45 1.20 60 280 33.0 0.32 2200
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 60 250 33.0 0.32 1180
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 60 210 33.0 0.30 1150
8 350 HB 0.5 3.5 0.18 0.40 1.00 60 180 22.7 0.30 1130
10 220 HB 0.5 4.0 0.18 0.40 1.20 35 190 22.5 0.30 1140
10 280 HB 0.5 4.0 0.18 0.40 1.20 35 150 22.5 0.30 1120
11 320 HB 0.5 3.0 0.18 0.35 0.80 35 130 22.2 0.28 1100
11 350 HB 0.5 3.0 0.18 0.35 0.80 35 110 22.2 0.28 990
14 180 HB 0.5 5.0 0.20 0.40 1.20 85 270 33.0 0.25 1190
14 240 HB 0.5 5.0 0.20 0.40 1.00 80 220 33.0 0.22 1170
14 290 HB 0.5 4.0 0.18 0.35 0.80 40 150 22.5 0.24 1100
14 310 HB 0.5 4.0 0.18 0.35 0.80 35 140 22.5 0.24 990
12 200 HB 0.5 5.0 0.18 0.40 0.70 85 250 22.5 0.20 1190
13 42 HRc 0.5 4.0 0.18 0.40 0.70 60 190 22.2 0.20 1130
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 60 250 33.0 0.30 1180
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 60 230 33.0 0.30 1160
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 60 190 33.0 0.30 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
TNMG 160408 NN – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.50 1.80 180 430 33.0 0.38 2265
2 190 HB 0.5 5.0 0.21 0.50 1.80 180 365 33.0 0.35 2240
3 250 HB 0.5 5.0 0.21 0.45 1.50 180 325 33.0 0.33 2220
6 180 HB 0.5 5.0 0.21 0.45 1.20 120 365 33.0 0.32 2220
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 325 33.0 0.32 2200
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 275 33.0 0.30 1165
8 350 HB 0.5 3.5 0.18 0.40 1.00 120 235 22.7 0.30 1145
10 220 HB 0.5 4.0 0.18 0.40 1.20 70 245 22.5 0.30 1155
10 280 HB 0.5 4.0 0.18 0.40 1.20 70 195 22.5 0.30 1130
11 320 HB 0.5 3.0 0.18 0.35 0.80 70 170 22.2 0.28 1110
11 350 HB 0.5 3.0 0.18 0.35 0.80 70 145 22.2 0.28 1100
15 150 HB 0.5 5.0 0.15 0.60 2.00 170 325 33.0 0.35 2220
15 200 HB 0.5 5.0 0.15 0.60 1.80 160 300 33.0 0.35 2200
16 250 HB 0.5 5.0 0.15 0.55 1.80 150 275 33.0 0.35 1175
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 325 33.0 0.30 2200
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 300 33.0 0.30 1175
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 245 33.0 0.30 1155
38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 130 22.0 0.25 990
38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 115 11.5 0.20 775
38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 105 11.0 0.18 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.25 0.40 40 80 11.5 0.18 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.20 0.30 30 65 11.0 0.15 445
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
Cast
Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
108
TURNING Machining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 5.0 0.18 0.50 1.70 180 330 33.0 0.33 2240
2 190 HB 0.5 5.0 0.18 0.50 1.70 180 280 33.0 0.33 2220
3 250 HB 0.5 5.0 0.18 0.45 1.45 180 250 33.0 0.33 2200
6 180 HB 0.5 5.0 0.18 0.45 1.15 120 280 33.0 0.30 2200
4,6 230 HB 0.5 4.0 0.18 0.45 1.15 120 250 33.0 0.30 1180
5,7 280 HB 0.5 4.0 0.16 0.40 1.15 120 210 33.0 0.29 1150
8 350 HB 0.5 3.5 0.16 0.40 0.95 120 180 33.0 0.29 1130
10 220 HB 0.5 4.0 0.16 0.40 1.15 70 190 22.5 0.29 1140
10 280 HB 0.5 4.0 0.16 0.40 1.15 70 150 22.5 0.29 1120
11 320 HB 0.5 3.0 0.16 0.35 0.75 70 130 22.5 0.27 1100
11 350 HB 0.5 3.0 0.16 0.35 0.75 70 110 22.5 0.27 990
14 180 HB 0.5 5.0 0.18 0.40 1.15 170 270 33.0 0.24 1190
14 240 HB 0.5 5.0 0.18 0.40 0.95 160 220 33.0 0.21 1170
14 290 HB 0.5 4.0 0.16 0.35 0.75 80 150 22.5 0.27 1100
14 310 HB 0.5 4.0 0.16 0.35 0.75 70 140 22.5 0.27 990
12 200 HB 0.5 5.0 0.19 0.40 0.95 170 250 22.5 0.29 1190
13 42 HRc 0.5 4.0 0.19 0.40 0.95 120 190 22.2 0.24 1130
15 150 HB 0.5 5.0 0.13 0.60 1.90 170 250 33.0 0.33 2200
15 200 HB 0.5 5.0 0.13 0.60 1.70 160 230 33.0 0.33 1180
16 250 HB 0.5 5.0 0.13 0.55 1.70 150 210 33.0 0.33 1160
17,19 150 HB 0.5 5.0 0.13 0.50 1.45 120 250 33.0 0.29 1180
17,19 200 HB 0.5 5.0 0.13 0.50 1.25 120 230 33.0 0.29 1160
18,20 250 HB 0.5 5.0 0.13 0.50 1.15 120 190 33.0 0.29 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.18 0.35 0.65 25 45 22.0 0.27 330
33 Inconel 700 250 HB 0.5 3.0 0.18 0.35 0.65 25 45 22.0 0.27 330
34 Stellite 21 350 HB 0.5 3.0 0.18 0.35 0.65 25 40 22.0 0.27 330
36 TiAl6V4 - 0.5 4.0 0.18 0.40 0.75 45 65 22.0 0.31 555
37 T40 - 0.5 3.0 0.18 0.35 0.65 35 55 22.0 0.29 445
38 45 HRc 0.5 2.5 0.10 0.30 0.55 50 100 22.0 0.24 880
38 50 HRc 0.5 2.0 0.10 0.25 0.40 40 90 11.5 0.19 770
38 55 HRc 0.5 1.5 0.10 0.20 0.30 40 80 11.0 0.17 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.10 0.25 0.40 40 60 11.5 0.17 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.20 0.30 30 50 11.0 0.14 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.18 0.60 1.70 200 400 33.0 0.38 280
St
eel
Non-alloyed
Low alloyed
Material Group
Suggested Starting Parameters
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
2
1C35, Ck45, 1020, 1045, 1060, 28Mn6
Amax [mm²]
D.O.C. [mm]VDI Group
Material Examples* HardnessVc [m/min]
Gr. N°
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Feed [mm/rev]
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
10
8
TNMG 160408 NX – LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
109
TURNINGMachining Conditions
TNMG 160408 NX – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.18 0.50 1.71 90 330 33.0 0.36 2240
2 190 HB 0.5 5.0 0.18 0.50 1.71 90 280 33.0 0.33 2220
3 250 HB 0.5 5.0 0.18 0.45 1.43 90 250 33.0 0.31 2200
6 180 HB 0.5 5.0 0.18 0.45 1.14 60 280 33.0 0.30 2200
4,6 230 HB 0.5 4.0 0.18 0.45 1.14 60 250 33.0 0.30 1180
5,7 280 HB 0.5 4.0 0.16 0.40 1.14 60 210 33.0 0.29 1150
8 350 HB 0.5 3.5 0.16 0.40 0.95 60 180 22.7 0.29 1130
10 220 HB 0.5 4.0 0.16 0.40 1.14 35 190 22.5 0.29 1140
10 280 HB 0.5 4.0 0.16 0.40 1.14 35 150 22.5 0.29 1120
11 320 HB 0.5 3.0 0.16 0.35 0.76 35 130 22.2 0.27 1100
11 350 HB 0.5 3.0 0.16 0.35 0.76 35 110 22.2 0.27 990
14 180 HB 0.5 5.0 0.18 0.40 1.14 85 270 33.0 0.24 1190
14 240 HB 0.5 5.0 0.18 0.40 0.95 80 220 33.0 0.21 1170
14 290 HB 0.5 4.0 0.16 0.35 0.76 40 150 22.5 0.23 1100
14 310 HB 0.5 4.0 0.16 0.35 0.76 35 140 22.5 0.23 990
12 200 HB 0.5 5.0 0.16 0.40 0.67 85 250 22.5 0.19 1190
13 42 HRc 0.5 4.0 0.16 0.40 0.67 60 190 22.2 0.19 1130
17,19 150 HB 0.5 5.0 0.13 0.50 1.43 60 250 33.0 0.29 1180
17,19 200 HB 0.5 5.0 0.13 0.50 1.24 60 230 33.0 0.29 1160
18,20 250 HB 0.5 5.0 0.13 0.50 1.14 60 190 33.0 0.29 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
TNMG 160408 NX – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.18 0.50 1.71 180 430 33.0 0.36 2265
2 190 HB 0.5 5.0 0.18 0.50 1.71 180 365 33.0 0.33 2240
3 250 HB 0.5 5.0 0.18 0.45 1.43 180 325 33.0 0.31 2220
6 180 HB 0.5 5.0 0.18 0.45 1.14 120 365 33.0 0.30 2220
4,6 230 HB 0.5 4.0 0.18 0.45 1.14 120 325 33.0 0.30 2200
5,7 280 HB 0.5 4.0 0.15 0.40 1.14 120 275 33.0 0.29 1165
8 350 HB 0.5 3.5 0.15 0.40 0.95 120 235 22.7 0.29 1145
10 220 HB 0.5 4.0 0.15 0.40 1.14 70 245 22.5 0.29 1155
10 280 HB 0.5 4.0 0.15 0.40 1.14 70 195 22.5 0.29 1130
11 320 HB 0.5 3.0 0.15 0.35 0.76 70 170 22.2 0.27 1110
11 350 HB 0.5 3.0 0.15 0.35 0.76 70 145 22.2 0.27 1100
15 150 HB 0.5 5.0 0.13 0.60 1.90 170 325 33.0 0.33 2220
15 200 HB 0.5 5.0 0.13 0.60 1.71 160 300 33.0 0.33 2200
16 250 HB 0.5 5.0 0.13 0.55 1.71 150 275 33.0 0.33 1175
17,19 150 HB 0.5 5.0 0.13 0.50 1.43 120 325 33.0 0.29 2200
17,19 200 HB 0.5 5.0 0.13 0.50 1.24 120 300 33.0 0.29 1175
18,20 250 HB 0.5 5.0 0.13 0.50 1.14 120 245 33.0 0.29 1155
38 45 HRc 0.5 2.5 0.09 0.30 0.57 50 130 22.0 0.24 990
38 50 HRc 0.5 2.0 0.09 0.25 0.38 40 115 11.5 0.19 775
38 55 HRc 0.5 1.5 0.09 0.20 0.29 40 105 11.0 0.17 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.09 0.25 0.38 40 80 11.5 0.17 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.09 0.20 0.29 30 65 11.0 0.14 445
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
7 GG20, GG40, EN-GJL-250,
No30B
8
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
110
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.7 5.0 0.26 0.68 3.06 180 330 44.0 0.46 2240
2 190 HB 0.7 5.0 0.26 0.68 3.06 180 280 44.0 0.46 2220
3 250 HB 0.7 5.0 0.26 0.61 2.55 180 250 44.0 0.46 2200
6 180 HB 0.7 5.0 0.26 0.61 2.04 120 280 44.0 0.42 2200
4,6 230 HB 0.7 4.0 0.26 0.61 2.04 120 250 44.0 0.42 1180
5,7 280 HB 0.7 4.0 0.23 0.54 2.04 120 210 44.0 0.40 1150
8 350 HB 0.7 3.5 0.23 0.54 1.70 120 180 44.0 0.40 1130
10 220 HB 0.7 4.0 0.23 0.54 2.04 70 190 33.4 0.40 1140
10 280 HB 0.7 4.0 0.23 0.54 2.04 70 150 33.4 0.40 1120
11 320 HB 0.7 3.0 0.23 0.47 1.36 70 130 33.4 0.37 1100
11 350 HB 0.7 3.0 0.23 0.47 1.36 70 110 33.4 0.37 990
14 180 HB 0.7 5.0 0.25 0.54 2.04 170 270 44.0 0.40 1190
14 240 HB 0.7 5.0 0.25 0.54 1.70 160 220 44.0 0.36 1170
14 290 HB 0.7 4.0 0.23 0.47 1.36 80 150 33.4 0.32 1100
14 310 HB 0.7 4.0 0.23 0.47 1.36 70 140 33.4 0.32 990
12 200 HB 0.7 5.0 0.28 0.54 1.70 170 250 44.0 0.40 1190
13 42 HRc 0.7 4.0 0.28 0.54 1.70 120 190 33.0 0.35 1130
15 150 HB 0.7 5.0 0.20 0.81 3.40 170 250 44.0 0.46 2200
15 200 HB 0.7 5.0 0.20 0.81 3.06 160 230 44.0 0.46 1180
16 250 HB 0.7 5.0 0.20 0.74 3.06 150 210 44.0 0.46 1160
17,19 150 HB 0.7 5.0 0.20 0.68 2.55 120 250 44.0 0.40 1180
17,19 200 HB 0.7 5.0 0.20 0.68 2.21 120 230 44.0 0.40 1160
18,20 250 HB 0.7 5.0 0.20 0.68 2.04 120 190 44.0 0.40 1140
31,32 Incoloy 800 240 HB 0.7 3.0 0.25 0.47 1.19 25 45 22.7 0.37 332
33 Inconel 700 250 HB 0.7 3.0 0.25 0.47 1.19 25 45 22.7 0.37 330
34 Stellite 21 350 HB 0.7 3.0 0.25 0.47 1.19 23 40 22.7 0.37 228
36 TiAl6V4 - 0.7 4.0 0.25 0.54 1.36 45 65 22.7 0.40 555
37 T40 - 0.7 3.0 0.25 0.47 1.19 35 55 22.7 0.37 445
38 45 HRc 0.7 2.5 0.14 0.41 1.02 50 100 22.2 0.33 880
38 50 HRc 0.7 2.0 0.14 0.34 0.68 40 90 22.0 0.26 770
38 55 HRc 0.7 1.5 0.14 0.27 0.51 40 80 11.3 0.24 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.0 0.14 0.34 0.68 40 60 22.0 0.24 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.5 0.14 0.27 0.51 30 50 11.3 0.20 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.7 6.0 0.25 0.81 3.10 200 400 4.0 0.50 280
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
TNMG 160412 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
111
TURNINGMachining Conditions
TNMG 160412 NN – LT 1025
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.7 5.0 0.26 0.68 3.06 90 330 33.6 0.50 2240
2 190 HB 0.7 5.0 0.26 0.68 3.06 90 280 33.6 0.46 2220
3 250 HB 0.7 5.0 0.26 0.61 2.55 90 250 33.6 0.44 2200
6 180 HB 0.7 5.0 0.26 0.61 2.04 60 280 33.6 0.42 2200
4,6 230 HB 0.7 4.0 0.26 0.61 2.04 60 250 33.6 0.42 1180
5,7 280 HB 0.7 4.0 0.23 0.54 2.04 60 210 33.6 0.40 1150
8 350 HB 0.7 3.5 0.23 0.54 1.70 60 180 33.2 0.40 1130
10 220 HB 0.7 4.0 0.23 0.54 2.04 35 190 33.0 0.40 1140
10 280 HB 0.7 4.0 0.23 0.54 2.04 35 150 33.0 0.40 1120
11 320 HB 0.7 3.0 0.23 0.47 1.36 35 130 22.6 0.37 1100
11 350 HB 0.7 3.0 0.23 0.47 1.36 35 110 22.6 0.37 990
14 180 HB 0.7 5.0 0.25 0.54 2.04 85 270 33.6 0.33 1190
14 240 HB 0.7 5.0 0.25 0.54 1.70 80 220 33.6 0.29 1170
14 290 HB 0.7 4.0 0.23 0.47 1.36 40 150 33.0 0.32 1100
14 310 HB 0.7 4.0 0.23 0.47 1.36 35 140 33.0 0.32 990
12 200 HB 0.7 5.0 0.23 0.54 1.19 85 250 33.0 0.26 1190
13 42 HRc 0.7 4.0 0.23 0.54 1.19 60 190 22.6 0.26 1130
17,19 150 HB 0.7 5.0 0.19 0.68 2.55 60 250 33.6 0.40 1180
17,19 200 HB 0.7 5.0 0.19 0.68 2.21 60 230 33.6 0.40 1160
18,20 250 HB 0.7 5.0 0.19 0.68 2.04 60 190 33.6 0.40 1140
Amax [mm²]
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
TNMG 160412 NN – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.7 5.0 0.26 0.68 3.06 180 430 33.6 0.50 2265
2 190 HB 0.7 5.0 0.26 0.68 3.06 180 365 33.6 0.46 2240
3 250 HB 0.7 5.0 0.26 0.61 2.55 180 325 33.6 0.44 2220
6 180 HB 0.7 5.0 0.26 0.61 2.04 120 365 33.6 0.42 2220
4,6 230 HB 0.7 4.0 0.26 0.61 2.04 120 325 33.6 0.42 2200
5,7 280 HB 0.7 4.0 0.23 0.54 2.04 120 275 33.6 0.40 1165
8 350 HB 0.7 3.5 0.23 0.54 1.70 120 235 33.2 0.40 1145
10 220 HB 0.7 4.0 0.23 0.54 2.04 70 245 33.0 0.40 1155
10 280 HB 0.7 4.0 0.23 0.54 2.04 70 195 33.0 0.40 1130
11 320 HB 0.7 3.0 0.23 0.47 1.36 70 170 22.6 0.37 1110
11 350 HB 0.7 3.0 0.23 0.47 1.36 70 145 22.6 0.37 1100
15 150 HB 0.7 5.0 0.19 0.81 3.40 170 325 33.6 0.46 2220
15 200 HB 0.7 5.0 0.19 0.81 3.06 160 300 33.6 0.46 2200
16 250 HB 0.7 5.0 0.19 0.74 3.06 150 275 33.6 0.46 1175
17,19 150 HB 0.7 5.0 0.19 0.68 2.55 120 325 33.6 0.40 2200
17,19 200 HB 0.7 5.0 0.19 0.68 2.21 120 300 33.6 0.40 1175
18,20 250 HB 0.7 5.0 0.19 0.68 2.04 120 245 33.6 0.40 1155
38 45 HRc 0.7 2.5 0.14 0.41 1.02 50 130 22.4 0.33 990
38 50 HRc 0.7 2.0 0.14 0.34 0.68 40 115 11.8 0.26 775
38 55 HRc 0.7 1.5 0.14 0.27 0.51 40 105 11.2 0.24 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.0 0.14 0.34 0.68 40 80 11.8 0.24 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.5 0.14 0.27 0.51 30 65 11.2 0.20 445
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
112
TURNING Machining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300
2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260
3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240
6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260
4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240
5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200
8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180
10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180
10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140
11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120
11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110
14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260
14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210
14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140
14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140
12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240
13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180
15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240
15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220
16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200
17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240
17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220
18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335
36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660
37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550
38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990
38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880
38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 00.9 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
TNMG 220404 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
113
TURNINGMachining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 7.0 0.21 0.50 1.80 180 330 33.0 0.35 2240
2 190 HB 0.5 7.0 0.21 0.50 1.80 180 280 33.0 0.35 2220
3 250 HB 0.5 7.0 0.21 0.45 1.50 180 250 33.0 0.35 2200
6 180 HB 0.5 7.0 0.21 0.45 1.20 120 280 33.0 0.32 2200
4,6 230 HB 0.5 5.6 0.21 0.45 1.20 120 250 33.0 0.32 1180
5,7 280 HB 0.5 5.6 0.18 0.40 1.20 120 210 33.0 0.30 1150
8 350 HB 0.5 4.9 0.18 0.40 1.00 120 180 33.0 0.30 1130
10 220 HB 0.5 5.6 0.18 0.40 1.20 70 190 22.5 0.30 1140
10 280 HB 0.5 5.6 0.18 0.40 1.20 70 150 22.5 0.30 1120
11 320 HB 0.5 4.2 0.18 0.35 0.80 70 130 22.5 0.28 1100
11 350 HB 0.5 4.2 0.18 0.35 0.80 70 110 22.5 0.28 990
14 180 HB 0.5 7.0 0.20 0.40 1.20 170 270 33.0 0.35 1190
14 240 HB 0.5 7.0 0.20 0.40 1.00 160 220 33.0 0.32 1170
14 290 HB 0.5 5.6 0.18 0.35 0.80 80 150 22.5 0.28 1100
14 310 HB 0.5 5.6 0.18 0.35 0.80 70 140 22.5 0.28 990
12 200 HB 0.5 7.0 0.22 0.40 1.00 170 250 33.0 0.32 1190
13 42 HRc 0.5 5.6 0.22 0.40 1.00 120 190 22.5 0.32 1130
15 150 HB 0.5 7.0 0.15 0.60 2.00 170 250 33.0 0.35 2200
15 200 HB 0.5 7.0 0.15 0.60 1.80 160 230 33.0 0.35 1180
16 250 HB 0.5 7.0 0.15 0.55 1.80 150 210 33.0 0.35 1160
17,19 150 HB 0.5 7.0 0.15 0.50 1.50 120 250 33.0 0.30 1180
17,19 200 HB 0.5 7.0 0.15 0.50 1.30 120 230 33.0 0.30 1160
18,20 250 HB 0.5 7.0 0.15 0.50 1.20 120 190 33.0 0.30 1140
31,32 Incoloy 800 240 HB 0.5 4.2 0.20 0.35 0.70 25 45 22.0 0.28 332
33 Inconel 700 250 HB 0.5 4.2 0.20 0.35 0.70 25 45 22.0 0.28 330
34 Stellite 21 350 HB 0.5 4.2 0.20 0.35 0.70 23 40 22.0 0.28 228
36 TiAl6V4 - 0.5 5.6 0.20 0.40 0.80 45 65 22.0 0.33 555
37 T40 - 0.5 4.2 0.20 0.35 0.70 35 55 22.0 0.30 445
38 45 HRc 0.5 3.5 0.11 0.30 0.60 50 100 22.0 0.25 880
38 50 HRc 0.5 2.8 0.11 0.25 0.40 40 90 11.5 0.20 770
38 55 HRc 0.5 2.1 0.11 0.20 0.30 40 80 11.0 0.18 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.8 0.11 0.25 0.40 40 60 11.5 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 2.1 0.11 0.20 0.30 30 50 11.0 0.15 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 8.4 0.20 0.60 1.80 200 400 3.0 0.40 280
St
eel
Non-alloyed
Low alloyed
Material Group Gr. N°
Suggested Starting Parameters
1C35, Ck45, 1020, 1045, 1060, 28Mn6
Amax [mm²]
D.O.C. [mm]VDI Group
Material Examples* HardnessFeed [mm/rev] Vc [m/min]
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
10
8
TNMG 220408 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
114
TURNING Machining Conditions
TNMG 220408 NN – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 7.0 0.21 0.50 1.80 90 330 33.0 0.38 2240
2 190 HB 0.5 7.0 0.21 0.50 1.80 90 280 33.0 0.35 2220
3 250 HB 0.5 7.0 0.21 0.45 1.50 90 250 33.0 0.33 2200
6 180 HB 0.5 7.0 0.21 0.45 1.20 60 280 33.0 0.32 2200
4,6 230 HB 0.5 5.6 0.21 0.45 1.20 60 250 33.0 0.32 1180
5,7 280 HB 0.5 5.6 0.18 0.40 1.20 60 210 33.0 0.30 1150
8 350 HB 0.5 4.9 0.18 0.40 1.00 60 180 22.7 0.30 1130
10 220 HB 0.5 5.6 0.18 0.40 1.20 35 190 22.5 0.30 1140
10 280 HB 0.5 5.6 0.18 0.40 1.20 35 150 22.5 0.30 1120
11 320 HB 0.5 4.2 0.18 0.35 0.80 35 130 22.2 0.28 1100
11 350 HB 0.5 4.2 0.18 0.35 0.80 35 110 22.2 0.28 990
14 180 HB 0.5 7.0 0.20 0.40 1.20 85 270 33.0 0.25 1190
14 240 HB 0.5 7.0 0.20 0.40 1.00 80 220 33.0 0.22 1170
14 290 HB 0.5 5.6 0.18 0.35 0.80 40 150 22.5 0.24 1100
14 310 HB 0.5 5.6 0.18 0.35 0.80 35 140 22.5 0.24 990
12 200 HB 0.5 7.0 0.18 0.40 0.70 85 250 22.5 0.20 1190
13 42 HRc 0.5 5.6 0.18 0.40 0.70 60 190 22.2 0.20 1130
17,19 150 HB 0.5 7.0 0.15 0.50 1.50 60 250 33.0 0.30 1180
17,19 200 HB 0.5 7.0 0.15 0.50 1.30 60 230 33.0 0.30 1160
18,20 250 HB 0.5 7.0 0.15 0.50 1.20 60 190 33.0 0.30 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
TNMG 220408 NN – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 7.0 0.21 0.50 1.80 180 430 33.0 0.38 2265
2 190 HB 0.5 7.0 0.21 0.50 1.80 180 365 33.0 0.35 2240
3 250 HB 0.5 7.0 0.21 0.45 1.50 180 325 33.0 0.33 2220
6 180 HB 0.5 7.0 0.21 0.45 1.20 120 365 33.0 0.32 2220
4,6 230 HB 0.5 5.6 0.21 0.45 1.20 120 325 33.0 0.32 2200
5,7 280 HB 0.5 5.6 0.18 0.40 1.20 120 275 33.0 0.30 1165
8 350 HB 0.5 4.9 0.18 0.40 1.00 120 235 22.7 0.30 1145
10 220 HB 0.5 5.6 0.18 0.40 1.20 70 245 22.5 0.30 1155
10 280 HB 0.5 5.6 0.18 0.40 1.20 70 195 22.5 0.30 1130
11 320 HB 0.5 4.2 0.18 0.35 0.80 70 170 22.2 0.28 1110
11 350 HB 0.5 4.2 0.18 0.35 0.80 70 145 22.2 0.28 1100
15 150 HB 0.5 7.0 0.15 0.60 2.00 170 325 33.0 0.35 2220
15 200 HB 0.5 7.0 0.15 0.60 1.80 160 300 33.0 0.35 2200
16 250 HB 0.5 7.0 0.15 0.55 1.80 150 275 33.0 0.35 1175
17,19 150 HB 0.5 7.0 0.15 0.50 1.50 120 325 33.0 0.30 2200
17,19 200 HB 0.5 7.0 0.15 0.50 1.30 120 300 33.0 0.30 1175
18,20 250 HB 0.5 7.0 0.15 0.50 1.20 120 245 33.0 0.30 1155
38 45 HRc 0.5 3.5 0.11 0.30 0.60 50 130 22.0 0.25 990
38 50 HRc 0.5 2.8 0.11 0.25 0.40 40 115 11.5 0.20 775
38 55 HRc 0.5 2.1 0.11 0.20 0.30 40 105 11.0 0.18 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.8 0.11 0.25 0.40 40 80 11.5 0.18 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 2.1 0.11 0.20 0.30 30 65 11.0 0.15 445
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
115
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 7.0 0.18 0.50 1.70 180 330 33.0 0.33 2240
2 190 HB 0.5 7.0 0.18 0.50 1.70 180 280 33.0 0.33 2220
3 250 HB 0.5 7.0 0.18 0.45 1.45 180 250 33.0 0.33 2200
6 180 HB 0.5 7.0 0.18 0.45 1.15 120 280 33.0 0.30 2200
4,6 230 HB 0.5 5.6 0.18 0.45 1.15 120 250 33.0 0.30 1180
5,7 280 HB 0.5 5.6 0.16 0.40 1.15 120 210 33.0 0.29 1150
8 350 HB 0.5 4.9 0.16 0.40 0.95 120 180 33.0 0.29 1130
10 220 HB 0.5 5.6 0.16 0.40 1.15 70 190 22.5 0.29 1140
10 280 HB 0.5 5.6 0.16 0.40 1.15 70 150 22.5 0.29 1120
11 320 HB 0.5 4.2 0.16 0.35 0.75 70 130 22.5 0.27 1100
11 350 HB 0.5 4.2 0.16 0.35 0.75 70 110 22.5 0.27 990
14 180 HB 0.5 7.0 0.18 0.40 1.15 170 270 33.0 0.24 1190
14 240 HB 0.5 7.0 0.18 0.40 0.95 160 220 33.0 0.21 1170
14 290 HB 0.5 5.6 0.16 0.35 0.75 80 150 22.5 0.27 1100
14 310 HB 0.5 5.6 0.16 0.35 0.75 70 140 22.5 0.27 990
12 200 HB 0.5 7.0 0.19 0.40 0.95 170 250 22.5 0.29 1190
13 42 HRc 0.5 5.6 0.19 0.40 0.95 120 190 22.5 0.24 1130
15 150 HB 0.5 7.0 0.13 0.60 1.90 170 250 33.0 0.33 2200
15 200 HB 0.5 7.0 0.13 0.60 1.70 160 230 33.0 0.33 1180
16 250 HB 0.5 7.0 0.13 0.55 1.70 150 210 33.0 0.33 1160
17,19 150 HB 0.5 7.0 0.13 0.50 1.45 120 250 33.0 0.29 1180
17,19 200 HB 0.5 7.0 0.13 0.50 1.25 120 230 33.0 0.29 1160
18,20 250 HB 0.5 7.0 0.13 0.50 1.15 120 190 33.0 0.29 1140
31,32 Incoloy 800 240 HB 0.5 4.2 0.18 0.35 0.65 25 45 22.0 0.27 330
33 Inconel 700 250 HB 0.5 4.2 0.18 0.35 0.65 25 45 22.0 0.27 330
34 Stellite 21 350 HB 0.5 4.2 0.18 0.35 0.65 25 40 22.0 0.27 330
36 TiAl6V4 - 0.5 5.6 0.18 0.40 0.75 45 65 22.0 0.31 555
37 T40 - 0.5 4.2 0.18 0.35 0.65 35 55 22.0 0.29 445
38 45 HRc 0.5 3.5 0.10 0.30 0.55 50 100 22.0 0.24 880
38 50 HRc 0.5 2.8 0.10 0.25 0.40 40 90 11.5 0.19 770
38 55 HRc 0.5 2.1 0.10 0.20 0.30 40 80 11.0 0.17 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.8 0.10 0.25 0.40 40 60 11.5 0.17 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 2.1 0.10 0.20 0.30 30 50 11.0 0.14 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 8.4 0.18 0.60 1.70 200 400 33.0 0.38 280
St
eel
Non-alloyed
Low alloyed
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
2
1C35, Ck45, 1020, 1045, 1060, 28Mn6
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42
304, 316, X5CrNi18-9
GGG40, GGG70, 50005
GG20, GG40, EN-GJL-250,
No30B
10
8
X2CrNiN23-4, S31500
Hard
ened
Mat
.
Steel
11
Stai
nles
s St
eel
Austenitic 4
Duplex 5
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based
Cast
Iron
Grey 7
Malleable & Nodular
TNMG 220408 NX – LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
116
TURNING Machining Conditions
TNMG 220408 NX – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 7.0 0.18 0.50 1.71 90 330 33.0 0.36 2240
2 190 HB 0.5 7.0 0.18 0.50 1.71 90 280 33.0 0.33 2220
3 250 HB 0.5 7.0 0.18 0.45 1.43 90 250 33.0 0.31 2200
6 180 HB 0.5 7.0 0.18 0.45 1.14 60 280 33.0 0.30 2200
4,6 230 HB 0.5 5.6 0.18 0.45 1.14 60 250 33.0 0.30 1180
5,7 280 HB 0.5 5.6 0.16 0.40 1.14 60 210 33.0 0.29 1150
8 350 HB 0.5 4.9 0.16 0.40 0.95 60 180 22.7 0.29 1130
10 220 HB 0.5 5.6 0.16 0.40 1.14 35 190 22.5 0.29 1140
10 280 HB 0.5 5.6 0.16 0.40 1.14 35 150 22.5 0.29 1120
11 320 HB 0.5 4.2 0.16 0.35 0.76 35 130 22.2 0.27 1100
11 350 HB 0.5 4.2 0.16 0.35 0.76 35 110 22.2 0.27 990
14 180 HB 0.5 7.0 0.18 0.40 1.14 85 270 33.0 0.24 1190
14 240 HB 0.5 7.0 0.18 0.40 0.95 80 220 33.0 0.21 1170
14 290 HB 0.5 5.6 0.16 0.35 0.76 40 150 22.5 0.23 1100
14 310 HB 0.5 5.6 0.16 0.35 0.76 35 140 22.5 0.23 990
12 200 HB 0.5 7.0 0.16 0.40 0.67 85 250 22.5 0.19 1190
13 42 HRc 0.5 5.6 0.16 0.40 0.67 60 190 22.2 0.19 1130
17,19 150 HB 0.5 7.0 0.13 0.50 1.43 60 250 33.0 0.29 1180
17,19 200 HB 0.5 7.0 0.13 0.50 1.24 60 230 33.0 0.29 1160
18,20 250 HB 0.5 7.0 0.13 0.50 1.14 60 190 33.0 0.29 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
TNMG 220408 NX – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 7.0 0.18 0.50 1.71 180 430 33.0 0.36 2265
2 190 HB 0.5 7.0 0.18 0.50 1.71 180 365 33.0 0.33 2240
3 250 HB 0.5 7.0 0.18 0.45 1.43 180 325 33.0 0.31 2220
6 180 HB 0.5 7.0 0.18 0.45 1.14 120 365 33.0 0.30 2220
4,6 230 HB 0.5 5.6 0.18 0.45 1.14 120 325 33.0 0.30 2200
5,7 280 HB 0.5 5.6 0.16 0.40 1.14 120 275 33.0 0.29 1165
8 350 HB 0.5 4.9 0.16 0.40 0.95 120 235 22.7 0.29 1145
10 220 HB 0.5 5.6 0.16 0.40 1.14 70 245 22.5 0.29 1155
10 280 HB 0.5 5.6 0.16 0.40 1.14 70 195 22.5 0.29 1130
11 320 HB 0.5 4.2 0.16 0.35 0.76 70 170 22.2 0.27 1110
11 350 HB 0.5 4.2 0.16 0.35 0.76 70 145 22.2 0.27 1100
15 150 HB 0.5 7.0 0.13 0.60 1.90 170 325 33.0 0.33 2220
15 200 HB 0.5 7.0 0.13 0.60 1.71 160 300 33.0 0.33 2200
16 250 HB 0.5 7.0 0.13 0.55 1.71 150 275 33.0 0.33 1175
17,19 150 HB 0.5 7.0 0.13 0.50 1.43 120 325 33.0 0.29 2200
17,19 200 HB 0.5 7.0 0.13 0.50 1.24 120 300 33.0 0.29 1175
18,20 250 HB 0.5 7.0 0.13 0.50 1.14 120 245 33.0 0.29 1155
38 45 HRc 0.5 3.5 0.10 0.30 0.57 50 130 22.0 0.24 990
38 50 HRc 0.5 2.8 0.10 0.25 0.38 40 115 11.5 0.19 775
38 55 HRc 0.5 2.1 0.10 0.20 0.29 40 105 11.0 0.17 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.8 0.10 0.25 0.38 40 80 11.5 0.17 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 2.1 0.10 0.20 0.29 30 65 11.0 0.14 445
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
117
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.7 7.0 0.26 0.68 3.06 180 330 44.0 0.46 2240
2 190 HB 0.7 7.0 0.26 0.68 3.06 180 280 44.0 0.46 2220
3 250 HB 0.7 7.0 0.26 0.61 2.55 180 250 44.0 0.46 2200
6 180 HB 0.7 7.0 0.26 0.61 2.04 120 280 44.0 0.42 2200
4,6 230 HB 0.7 5.6 0.26 0.61 2.04 120 250 44.0 0.42 1180
5,7 280 HB 0.7 5.6 0.23 0.54 2.04 120 210 44.0 0.40 1150
8 350 HB 0.7 4.9 0.23 0.54 1.70 120 180 44.0 0.40 1130
10 220 HB 0.7 5.6 0.23 0.54 2.04 70 190 33.4 0.40 1140
10 280 HB 0.7 5.6 0.23 0.54 2.04 70 150 33.4 0.40 1120
11 320 HB 0.7 4.2 0.23 0.47 1.36 70 130 33.4 0.37 1100
11 350 HB 0.7 4.2 0.23 0.47 1.36 70 110 33.4 0.37 990
14 180 HB 0.7 7.0 0.25 0.54 2.04 170 270 44.0 0.40 1190
14 240 HB 0.7 7.0 0.25 0.54 1.70 160 220 44.0 0.36 1170
14 290 HB 0.7 5.6 0.23 0.47 1.36 80 150 33.4 0.32 1100
14 310 HB 0.7 5.6 0.23 0.47 1.36 70 140 33.4 0.32 990
12 200 HB 0.7 7.0 0.28 0.54 1.70 170 250 44.0 0.40 1190
13 42 HRc 0.7 5.6 0.28 0.54 1.70 120 190 33.0 0.35 1130
15 150 HB 0.7 7.0 0.20 0.81 3.40 170 250 44.0 0.46 2200
15 200 HB 0.7 7.0 0.20 0.81 3.06 160 230 44.0 0.46 1180
16 250 HB 0.7 7.0 0.20 0.74 3.06 150 210 44.0 0.46 1160
17,19 150 HB 0.7 7.0 0.20 0.68 2.55 120 250 44.0 0.40 1180
17,19 200 HB 0.7 7.0 0.20 0.68 2.21 120 230 44.0 0.40 1160
18,20 250 HB 0.7 7.0 0.20 0.68 2.04 120 190 44.0 0.40 1140
31,32 Incoloy 800 240 HB 0.7 4.2 0.25 0.47 1.19 25 45 22.7 0.37 332
33 Inconel 700 250 HB 0.7 4.2 0.25 0.47 1.19 25 45 22.7 0.37 330
34 Stellite 21 350 HB 0.7 4.2 0.25 0.47 1.19 23 40 22.7 0.37 228
36 TiAl6V4 - 0.7 5.6 0.25 0.54 1.36 45 65 22.7 0.40 555
37 T40 - 0.7 4.2 0.25 0.47 1.19 35 55 22.7 0.37 445
38 45 HRc 0.7 3.5 0.14 0.41 1.02 50 100 22.2 0.33 880
38 50 HRc 0.7 2.8 0.14 0.34 0.68 40 90 22.0 0.26 770
38 55 HRc 0.7 2.1 0.14 0.27 0.51 40 80 11.3 0.24 660Chilled Cast
IIron40 Ni-Hard 2 400 HB 0.7 2.8 0.14 0.34 0.68 40 60 22.0 0.24 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 2.1 0.14 0.27 0.51 30 50 11.3 0.20 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.7 7.0 0.25 0.81 3.10 200 400 44.0 0.50 280
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic
6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
TNMG 220412 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
118
TURNING Machining Conditions
TNMG 220412 NN – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.7 7.0 0.26 0.68 3.06 90 330 44.0 00.50 2240
2 190 HB 0.7 7.0 0.26 0.68 3.06 90 280 44.0 00.46 2220
3 250 HB 0.7 7.0 0.26 0.61 2.55 90 250 44.0 00.44 2200
6 180 HB 0.7 7.0 0.26 0.61 2.04 60 280 44.0 00.42 2200
4,6 230 HB 0.7 5.6 0.26 0.61 2.04 60 250 44.0 00.42 1180
5,7 280 HB 0.7 5.6 0.23 0.54 2.04 60 210 44.0 00.40 1150
8 350 HB 0.7 4.9 0.23 0.54 1.70 60 180 33.6 00.40 1130
10 220 HB 0.7 5.6 0.23 0.54 2.04 35 190 33.4 00.40 1140
10 280 HB 0.7 5.6 0.23 0.54 2.04 35 150 33.4 00.40 1120
11 320 HB 0.7 4.2 0.23 0.47 1.36 35 130 22.9 00.37 1100
11 350 HB 0.7 4.2 0.23 0.47 1.36 35 110 22.9 00.37 990
14 180 HB 0.7 7.0 0.25 0.54 2.04 85 270 44.0 00.33 1190
14 240 HB 0.7 7.0 0.25 0.54 1.70 80 220 44.0 00.29 1170
14 290 HB 0.7 5.6 0.23 0.47 1.36 40 150 33.4 00.32 1100
14 310 HB 0.7 5.6 0.23 0.47 1.36 35 140 33.4 00.32 990
12 200 HB 0.7 7.0 0.23 0.54 1.19 85 250 33.4 00.26 1190
13 42 HRc 0.7 5.6 0.23 0.54 1.19 60 190 22.9 00.26 1130
17,19 150 HB 0.7 7.0 0.19 0.68 2.55 60 250 44.0 00.40 1180
17,19 200 HB 0.7 7.0 0.19 0.68 2.21 60 230 44.0 00.40 1160
18,20 250 HB 0.7 7.0 0.19 0.68 2.04 60 190 44.0 00.40 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
TNMG 220412 NN – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.7 7.0 0.26 0.68 3.06 180 430 44.0 00.50 2265
2 190 HB 0.7 7.0 0.26 0.68 3.06 180 365 44.0 00.46 2240
3 250 HB 0.7 7.0 0.26 0.61 2.55 180 325 44.0 00.44 2220
6 180 HB 0.7 7.0 0.26 0.61 2.04 120 365 44.0 00.42 2220
4,6 230 HB 0.7 5.6 0.26 0.61 2.04 120 325 44.0 00.42 2200
5,7 280 HB 0.7 5.6 0.23 0.54 2.04 120 275 44.0 00.40 1165
8 350 HB 0.7 4.9 0.23 0.54 1.70 120 235 33.6 00.40 1145
10 220 HB 0.7 5.6 0.23 0.54 2.04 70 245 33.4 00.40 1155
10 280 HB 0.7 5.6 0.23 0.54 2.04 70 195 33.4 00.40 1130
11 320 HB 0.7 4.2 0.23 0.47 1.36 70 170 22.9 00.37 1110
11 350 HB 0.7 4.2 0.23 0.47 1.36 70 145 22.9 00.37 1100
15 150 HB 0.7 7.0 0.19 0.81 3.40 170 325 44.0 00.46 2220
15 200 HB 0.7 7.0 0.19 0.81 3.06 160 300 44.0 00.46 2200
16 250 HB 0.7 7.0 0.19 0.74 3.06 150 275 44.0 00.46 1175
17,19 150 HB 0.7 7.0 0.19 0.68 2.55 120 325 44.0 00.40 2200
17,19 200 HB 0.7 7.0 0.19 0.68 2.21 120 300 44.0 00.40 1175
18,20 250 HB 0.7 7.0 0.19 0.68 2.04 120 245 44.0 00.40 1155
38 45 HRc 0.7 3.5 0.14 0.41 1.02 50 130 22.7 00.33 990
38 50 HRc 0.7 2.8 0.14 0.34 0.68 40 115 22.0 00.26 775
38 55 HRc 0.7 2.1 0.14 0.27 0.51 40 105 11.3 00.24 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.8 0.14 0.34 0.68 40 80 22.0 00.24 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 2.1 0.14 0.27 0.51 30 65 11.3 00.20 445
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
119
TURNING
NXCNMPTNMPWNMP
Exotic Material
Cutting Conditions!Verify
T N M P
Shape Toleranced ± 0.05m ± 0.08s ± 0.13
0°
Clearance Anglel
m
Ø d60°
Fixing,Chipbreaker
ss
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00041450.804.7616TNMP 160408 NN LT 1025
LT 1025 Recommended for moderate to low speed
60° triangle shape inserts with positive chip breaker geometry. Generates low cutting forces. Suitable for general purpose, copying, high temperature alloys and stainless steel turning operations.
TNMP
120
TURNING Machining Conditions
TNMP 160408 NN – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.50 1.80 90 330 33.0 00.38 2240
2 190 HB 0.5 5.0 0.21 0.50 1.80 90 280 33.0 00.35 2220
3 250 HB 0.5 5.0 0.21 0.45 1.50 90 250 33.0 00.33 2200
6 180 HB 0.5 5.0 0.21 0.45 1.20 60 280 33.0 00.32 2200
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 60 250 33.0 00.32 1180
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 60 210 33.0 00.30 1150
8 350 HB 0.5 3.5 0.18 0.40 1.00 60 180 22.7 00.30 1130
10 220 HB 0.5 4.0 0.18 0.40 1.20 35 190 22.5 00.30 1140
10 280 HB 0.5 4.0 0.18 0.40 1.20 35 150 22.5 00.30 1120
11 320 HB 0.5 3.0 0.18 0.35 0.80 35 130 22.2 00.28 1100
11 350 HB 0.5 3.0 0.18 0.35 0.80 35 110 22.2 00.28 990
14 180 HB 0.5 5.0 0.20 0.40 1.20 85 270 33.0 00.25 1190
14 240 HB 0.5 5.0 0.20 0.40 1.00 80 220 33.0 00.22 1170
14 290 HB 0.5 4.0 0.18 0.35 0.80 40 150 22.5 00.24 1100
14 310 HB 0.5 4.0 0.18 0.35 0.80 35 140 22.5 00.24 990
12 200 HB 0.5 5.0 0.18 0.40 0.70 85 250 22.5 00.20 1190
13 42 HRc 0.5 4.0 0.18 0.40 0.70 60 190 22.2 00.20 1130
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 60 250 33.0 00.30 1180
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 60 230 33.0 00.30 1160
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 60 190 33.0 00.30 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
FFerritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
CCast
Iron
MMalleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
HHigh alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
SStai
nles
s St
eel
AAustenitic 4304, 316,
X5CrNi18-9
DDuplex 5
St
eel
NNon-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
LLow alloyed 2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
121
TURNING
FProductivity
Stainless Steel
VC
T N U X
Shape Toleranced ± 0.08m ± 0.13s ± 0.13
0°
Clearance Angle Fixing,Chipbreaker
l
m
Ø d60°
s
F M R
Application Guide
Insert Designation s r Catalog Nr.l
LT 10 Multi-MatTM General Usage – Standard
T00033850.804.7616TNUX 160408 L LT10
T00011370.804.7616TNUX 160408 R LT 10
T00018770.404.7616TNUX 160404 L LT 10
T00011250.404.7616TNUX 160404 R LT 10
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00027950.804.7616TNUX 160408 L LT 1000
T00019390.804.7616TNUX 160408 R LT 1000
T00027940.404.7616TNUX 160404 L LT 1000
T00019380.404.7616TNUX 160404 R LT 1000
LT 1000 Multi-MatTM General Usage – Premium
Sh
60° triangle shape inserts. Suitable for general turning and longitudinal operations, where there is a con-cern for work piece vibrations.
Left
TNUX
122
TURNING
min max min max min max D.O.C. Feed
1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300
2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260
3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240
6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260
4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240
5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200
8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180
10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180
10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140
11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120
11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110
14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260
14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210
14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140
14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140
12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240
13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180
15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240
15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220
16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200
17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240
17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220
18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335
36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660
37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550
38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990
38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880
38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 00.9 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
TNUX 160404 L/R – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
123
TURNINGMachining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240
2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220
3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200
6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150
8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130
10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140
10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120
11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100
11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990
14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190
14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170
14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100
14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990
12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190
13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130
15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200
15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180
16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332
33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330
34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228
36 TiAl6V4 - 0.5 4.0 0.20 0.40 0.80 45 65 22.0 0.33 555
37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445
38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880
38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770
38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.25 0.40 40 60 11.5 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.20 0.30 30 50 11.0 0.15 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 33.0 0.40 280
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
10
8
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
Suggested Starting Parameters
1C35, Ck45, 1020, 1045, 1060, 28Mn6
Amax [mm²]
D.O.C. [mm]VDI Group
Material Examples* HardnessFeed [mm/rev] Vc [m/min]
St
eel
Non-alloyed
Low alloyed
Material Group Gr. N°
TNUX 160408 L/R – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
124
TURNING
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
FProductivity
Stainless Steel
VC
T P M R
Shape Toleranced ± 0.05m ± 0.08s ± 0.13
Clearance Angle
11°
Fixing,Chipbreaker
l
m
Ø d60°
s
F M R
Application Guide
Insert Designation s r Catalog Nr.l
LT 10 Multi-MatTM General Usage – Standard
T00015350.803.7616TPMR 160308 NN LT 10
T00016380.403.7616TPMR 160304 NN LT 10
60° triangle shape inserts with positive rake angle. Suitable for boring and internal turing operations.
125
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300
2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260
3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240
6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260
4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240
5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200
8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180
10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180
10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140
11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120
11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110
14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260
14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210
14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140
14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140
12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240
13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180
15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240
15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220
16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200
17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240
17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220
18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335
36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660
37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550
38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990
38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880
38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 00.9 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
TPMR 160304 NN – LT 10
TPMR
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
126
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240
2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220
3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200
6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200
4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180
5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150
8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130
10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140
10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120
11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100
11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990
14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190
14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170
14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100
14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990
12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190
13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130
15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200
15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180
16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160
17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180
17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160
18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140
31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332
33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330
34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228
36 TiAl6V4 - 0.5 4.0 0.20 0.40 0.80 45 65 22.0 0.33 555
37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445
38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880
38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770
38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.11 0.25 0.40 40 60 11.5 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.20 0.30 30 50 11.0 0.15 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 3.0 0.40 280
St
eel
Non-alloyed
Low alloyed
1C35, Ck45, 1020,
1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Stai
nles
s St
eel
Austenitic 4304, 316, X5CrNi18-
9
Duplex
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
10
8
TPMR 160308 NN – LT 10
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
127
TURNING
FProductivity
Stainless Steel
VC
V B M T
Shape Toleranced ± 0.05m ± 0.08s ± 0.13
Clearance Angle
5°
Fixing,Chipbreaker
35° Ø d
l
m
s
F M R
Application Guide
Insert Designation s r Catalog Nr.l
LT 10 Multi-MatTM General Usage – Standard
T00000710.804.7616VBMT 160408 NN LT 10
T00000700.404.7616VBMT 160404 NN LT 10
T00014600.403.7611VBMT 110304 NN LT 10
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00019440.804.7616VBMT 160408 NN LT 1000
T00019430.404.7616VBMT 160404 NN LT 1000
T00019420.403.7611VBMT 110304 NN LT 1000
LT 1000 Multi-MatTM General Usage – Premium
35° diamond shape inserts with positive rake angle. Suitable for internal and external copying operations of complex geometries.
VBMT
128
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.3 2.1 0.08 0.20 0.37 180 330 11.0 0.14 3300
2 190 HB 0.3 1.8 0.08 0.19 0.32 180 280 11.0 0.14 2260
3 250 HB 0.3 1.8 0.08 0.17 0.30 180 250 11.0 0.14 2240
6 180 HB 0.3 1.8 0.08 0.17 0.31 120 280 11.0 0.11 2260
4,6 230 HB 0.3 1.8 0.08 0.17 0.30 120 250 11.0 0.11 2240
5,7 280 HB 0.3 1.4 0.08 0.15 0.25 120 210 11.0 0.10 2200
8 350 HB 0.3 1.4 0.08 0.15 0.22 120 180 11.0 0.10 1180
10 220 HB 0.3 1.8 0.07 0.15 0.25 70 190 00.9 0.08 1180
10 280 HB 0.3 1.8 0.07 0.14 0.25 70 150 00.9 0.08 1140
11 320 HB 0.3 1.4 0.07 0.12 0.20 70 130 00.9 0.08 1120
11 350 HB 0.3 1.4 0.07 0.12 0.16 70 110 00.9 0.08 1110
14 180 HB 0.3 1.8 0.06 0.15 0.20 170 270 11.0 0.07 2260
14 240 HB 0.3 1.8 0.06 0.15 0.16 160 220 11.0 0.06 2210
14 290 HB 0.3 1.4 0.06 0.12 0.12 80 150 00.9 0.06 1140
14 310 HB 0.3 1.4 0.06 0.12 0.12 70 140 00.9 0.06 1140
12 200 HB 0.3 1.8 0.06 0.15 0.20 170 250 00.9 0.07 2240
13 42 HRc 0.3 1.4 0.06 0.14 0.16 120 190 00.8 0.06 1180
15 150 HB 0.3 2.1 0.06 0.17 0.40 170 250 11.0 0.14 2240
15 200 HB 0.3 2.1 0.06 0.17 0.37 160 230 11.0 0.14 2220
16 250 HB 0.3 2.1 0.06 0.17 0.37 150 210 11.0 0.14 2200
17,19 150 HB 0.3 1.8 0.06 0.15 0.30 120 250 11.0 0.10 2240
17,19 200 HB 0.3 1.8 0.06 0.15 0.25 120 230 11.0 0.10 2220
18,20 250 HB 0.3 1.8 0.06 0.15 0.25 120 190 11.0 0.10 1180
31,32 Incoloy 800 240 HB 0.3 1.4 0.07 0.13 0.16 25 50 00.7 0.08 440
33 Inconel 700 250 HB 0.3 1.4 0.07 0.13 0.16 25 50 00.7 0.08 440
34 Stellite 21 350 HB 0.3 1.4 0.07 0.13 0.16 23 45 00.7 0.08 335
36 TiAl6V4 - 0.3 1.4 0.07 0.14 0.20 45 65 00.7 0.11 660
37 T40 - 0.3 1.4 0.07 0.12 0.16 35 60 00.7 0.08 550
38 45 HRc 0.3 1.3 0.04 0.10 0.12 50 100 00.7 0.08 990
38 50 HRc 0.3 1.1 0.04 0.09 0.11 40 90 00.6 0.06 880
38 55 HRc 0.3 1.0 0.04 0.08 0.08 40 80 00.5 0.05 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.1 0.04 0.10 0.11 40 60 00.6 0.08 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.0 0.04 0.08 0.08 30 50 00.5 0.05 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 2.8 0.08 0.26 0.43 200 400 1.0 0.18 350
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
VBMT 110304 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
129
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300
2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260
3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240
6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260
4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240
5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200
8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180
10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180
10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140
11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120
11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110
14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260
14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210
14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140
14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140
12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240
13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180
15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240
15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220
16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200
17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240
17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220
18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335
36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660
37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550
38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990
38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880
38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 00.9 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
VBMT 160404 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
130
TURNING Machining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 3.5 0.19 0.40 1.26 180 330 22.5 0.30 2240
2 190 HB 0.5 3.5 0.19 0.40 1.26 180 280 22.5 0.30 2220
3 250 HB 0.5 3.5 0.19 0.36 1.05 180 250 22.5 0.30 2200
6 180 HB 0.5 3.5 0.19 0.36 0.84 120 280 22.5 0.27 2200
4,6 230 HB 0.5 2.8 0.19 0.36 0.84 120 250 22.5 0.27 1180
5,7 280 HB 0.5 2.8 0.16 0.32 0.84 120 210 22.5 0.26 1150
8 350 HB 0.5 2.5 0.16 0.32 0.70 120 180 22.5 0.26 1130
10 220 HB 0.5 2.8 0.16 0.32 0.84 70 190 22.1 0.26 1140
10 280 HB 0.5 2.8 0.16 0.32 0.84 70 150 22.1 0.26 1120
11 320 HB 0.5 2.1 0.16 0.28 0.56 70 130 22.1 0.24 1100
11 350 HB 0.5 2.1 0.16 0.28 0.56 70 110 22.1 0.24 990
14 180 HB 0.5 3.5 0.18 0.32 0.84 170 270 22.5 0.30 1190
14 240 HB 0.5 3.5 0.18 0.32 0.70 160 220 22.5 0.27 1170
14 290 HB 0.5 2.8 0.16 0.28 0.56 80 150 22.1 0.24 1100
14 310 HB 0.5 2.8 0.16 0.28 0.56 70 140 22.1 0.24 990
12 200 HB 0.5 3.5 0.20 0.32 0.70 170 250 22.5 0.27 1190
13 42 HRc 0.5 2.8 0.20 0.32 0.70 120 190 22.5 0.27 1130
15 150 HB 0.5 3.5 0.14 0.48 1.40 170 250 22.5 0.30 2200
15 200 HB 0.5 3.5 0.14 0.48 1.26 160 230 22.5 0.30 1180
16 250 HB 0.5 3.5 0.14 0.44 1.26 150 210 22.5 0.30 1160
17,19 150 HB 0.5 3.5 0.14 0.40 1.05 120 250 22.5 0.26 1180
17,19 200 HB 0.5 3.5 0.14 0.40 0.91 120 230 22.5 0.26 1160
18,20 250 HB 0.5 3.5 0.14 0.40 0.84 120 190 22.5 0.26 1140
31,32 Incoloy 800 240 HB 0.5 2.1 0.18 0.28 0.49 25 45 22.0 0.24 332
33 Inconel 700 250 HB 0.5 2.1 0.18 0.28 0.49 25 45 22.0 0.24 330
34 Stellite 21 350 HB 0.5 2.1 0.18 0.28 0.49 23 40 22.0 0.24 228
36 TiAl6V4 - 0.5 2.8 0.18 0.32 0.56 45 65 22.0 0.28 555
37 T40 - 0.5 2.1 0.18 0.28 0.49 35 55 22.0 0.26 445
38 45 HRc 0.5 1.8 0.10 0.24 0.42 50 100 11.6 0.21 880
38 50 HRc 0.5 1.4 0.10 0.20 0.28 40 90 11.2 0.17 770
38 55 HRc 0.5 1.1 0.10 0.16 0.21 40 80 11.0 0.15 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.4 0.10 0.20 0.28 40 60 11.2 0.15 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.1 0.10 0.16 0.21 30 50 11.0 0.13 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.2 0.18 0.48 1.40 200 400 22.5 0.34 280
St
eel
Non-alloyed
Low alloyed
Material Group Gr. N°
Suggested Starting Parameters
1C35, Ck45, 1020, 1045, 1060, 28Mn6
Amax [mm²]
D.O.C. [mm]VDI Group
Material Examples* HardnessFeed [mm/rev] Vc [m/min]
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
10
8
VBMT 160408 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
131
TURNING
FProductivity
Stainless Steel
VC
V C M T
Shape Toleranced ± 0.05m ± 0.08s ± 0.13
Clearance Angle
7°
Fixing,Chipbreaker
35° Ø d
l
m
s
F M R
Application Guide
Insert Designation s r Catalog Nr.l
LT 10 Multi-MatTM General Usage – Standard
T00011030.804.7616VCMT 160408 NN LT 10
T00011020.404.7616VCMT 160404 NN LT 10
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00019460.804.7616VCMT 160408 NN LT 1000
T00019450.404.7616VCMT 160404 NN LT 1000
LT 1000 Multi-MatTM General Usage – Premium
35° diamond shape inserts with positive rake angle. Suitable for internal and external copying operations of complex geometries.
VCMT
132
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300
2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260
3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240
6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260
4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240
5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200
8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180
10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180
10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140
11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120
11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110
14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260
14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210
14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140
14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140
12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240
13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180
15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240
15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220
16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200
17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240
17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220
18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335
36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660
37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550
38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990
38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880
38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 00.9 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
VCMT 160404 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
133
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 3.5 0.19 0.40 1.26 180 330 22.5 0.30 2240
2 190 HB 0.5 3.5 0.19 0.40 1.26 180 280 22.5 0.30 2220
3 250 HB 0.5 3.5 0.19 0.36 1.05 180 250 22.5 0.30 2200
6 180 HB 0.5 3.5 0.19 0.36 0.84 120 280 22.5 0.27 2200
4,6 230 HB 0.5 2.8 0.19 0.36 0.84 120 250 22.5 0.27 1180
5,7 280 HB 0.5 2.8 0.16 0.32 0.84 120 210 22.5 0.26 1150
8 350 HB 0.5 2.5 0.16 0.32 0.70 120 180 22.5 0.26 1130
10 220 HB 0.5 2.8 0.16 0.32 0.84 70 190 22.1 0.26 1140
10 280 HB 0.5 2.8 0.16 0.32 0.84 70 150 22.1 0.26 1120
11 320 HB 0.5 2.1 0.16 0.28 0.56 70 130 22.1 0.24 1100
11 350 HB 0.5 2.1 0.16 0.28 0.56 70 110 22.1 0.24 990
14 180 HB 0.5 3.5 0.18 0.32 0.84 170 270 22.5 0.30 1190
14 240 HB 0.5 3.5 0.18 0.32 0.70 160 220 22.5 0.27 1170
14 290 HB 0.5 2.8 0.16 0.28 0.56 80 150 22.1 0.24 1100
14 310 HB 0.5 2.8 0.16 0.28 0.56 70 140 22.1 0.24 990
12 200 HB 0.5 3.5 0.20 0.32 0.70 170 250 22.5 0.27 1190
13 42 HRc 0.5 2.8 0.20 0.32 0.70 120 190 22.5 0.27 1130
15 150 HB 0.5 3.5 0.14 0.48 1.40 170 250 22.5 0.30 2200
15 200 HB 0.5 3.5 0.14 0.48 1.26 160 230 22.5 0.30 1180
16 250 HB 0.5 3.5 0.14 0.44 1.26 150 210 22.5 0.30 1160
17,19 150 HB 0.5 3.5 0.14 0.40 1.05 120 250 22.5 0.26 1180
17,19 200 HB 0.5 3.5 0.14 0.40 0.91 120 230 22.5 0.26 1160
18,20 250 HB 0.5 3.5 0.14 0.40 0.84 120 190 22.5 0.26 1140
31,32 Incoloy 800 240 HB 0.5 2.1 0.18 0.28 0.49 25 45 22.0 0.24 332
33 Inconel 700 250 HB 0.5 2.1 0.18 0.28 0.49 25 45 22.0 0.24 330
34 Stellite 21 350 HB 0.5 2.1 0.18 0.28 0.49 23 40 22.0 0.24 228
36 TiAl6V4 - 0.5 2.8 0.18 0.32 0.56 45 65 22.0 0.28 555
37 T40 - 0.5 2.1 0.18 0.28 0.49 35 55 22.0 0.26 445
38 45 HRc 0.5 1.8 0.10 0.24 0.42 50 100 11.6 0.21 880
38 50 HRc 0.5 1.4 0.10 0.20 0.28 40 90 11.2 0.17 770
38 55 HRc 0.5 1.1 0.10 0.16 0.21 40 80 11.0 0.15 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.4 0.10 0.20 0.28 40 60 11.2 0.15 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.1 0.10 0.16 0.21 30 50 11.0 0.13 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.2 0.18 0.48 1.40 200 400 22.5 0.34 280
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
10
8
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
1C35, Ck45, 1020, 1045, 1060, 28Mn6
St
eel
Non-alloyed
Low alloyed
VCMT 160408 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
134
TURNING
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
V N M G
Shape Toleranced ± 0.05m ± 0.08s ± 0.13
Clearance Angle
0°
Fixing,Chipbreaker
35° Ø d
l
m
ss
F M R
Application Guide
Insert Designation s r Catalog Nr.l
LT 10 Multi-MatTM General Usage – Standard
T00000730.804.7616VNMG 160408 NN LT 10
T00000720.404.7616VNMG 160404 NN LT 10
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00040950.804.7616VNMG 160408 NN LT 1005
LT 1005 Recommended for moderate to high speed
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00041490.804.7616VNMG 160408 NN LT 1025
LT 1025 Recommended for moderate to low speed
F M R
Application Guide
s r Catalog Nr.l
T00019480.804.7616VNMG 160408 NN LT 1000
T00019470.404.7616VNMG 160404 NN LT 1000
Insert Designation
LT 1000 Multi-MatTM General Usage – Premium
35° diamond shape inserts. Suitable for external copying operations.
LT 1005
FProductivity
Stainless Steel
VC
LT 10 and LT 1000 LT 10 and LT 1000
VC
Productivity
135
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300
2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260
3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240
6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260
4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240
5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200
8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180
10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180
10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140
11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120
11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110
14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260
14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210
14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140
14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140
12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240
13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180
15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240
15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220
16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200
17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240
17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220
18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335
36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660
37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550
38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990
38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880
38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 00.9 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
VNMG 160404 NN – LT 10 | LT 1000
VNMG
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
136
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 4.0 0.19 0.40 1.44 180 330 22.7 0.32 2240
2 190 HB 0.5 4.0 0.19 0.40 1.44 180 280 22.7 0.32 2220
3 250 HB 0.5 4.0 0.19 0.36 1.20 180 250 22.7 0.32 2200
6 180 HB 0.5 4.0 0.19 0.36 0.96 120 280 22.7 0.29 2200
4,6 230 HB 0.5 3.2 0.19 0.36 0.96 120 250 22.7 0.29 1180
5,7 280 HB 0.5 3.2 0.16 0.32 0.96 120 210 22.7 0.27 1150
8 350 HB 0.5 2.8 0.16 0.32 0.80 120 180 22.7 0.27 1130
10 220 HB 0.5 3.2 0.16 0.32 0.96 70 190 22.3 0.27 1140
10 280 HB 0.5 3.2 0.16 0.32 0.96 70 150 22.3 0.27 1120
11 320 HB 0.5 2.4 0.16 0.28 0.64 70 130 22.3 0.25 1100
11 350 HB 0.5 2.4 0.16 0.28 0.64 70 110 22.3 0.25 990
14 180 HB 0.5 4.0 0.18 0.32 0.96 170 270 22.7 0.32 1190
14 240 HB 0.5 4.0 0.18 0.32 0.80 160 220 22.7 0.29 1170
14 290 HB 0.5 3.2 0.16 0.28 0.64 80 150 22.3 0.25 1100
14 310 HB 0.5 3.2 0.16 0.28 0.64 70 140 22.3 0.25 990
12 200 HB 0.5 4.0 0.20 0.32 0.80 170 250 22.7 0.29 1190
13 42 HRc 0.5 3.2 0.20 0.32 0.80 120 190 22.5 0.29 1130
15 150 HB 0.5 4.0 0.14 0.48 1.60 170 250 22.7 0.32 2200
15 200 HB 0.5 4.0 0.14 0.48 1.44 160 230 22.7 0.32 1180
16 250 HB 0.5 4.0 0.14 0.44 1.44 150 210 22.7 0.32 1160
17,19 150 HB 0.5 4.0 0.14 0.40 1.20 120 250 22.7 0.27 1180
17,19 200 HB 0.5 4.0 0.14 0.40 1.04 120 230 22.7 0.27 1160
18,20 250 HB 0.5 4.0 0.14 0.40 0.96 120 190 22.7 0.27 1140
31,32 Incoloy 800 240 HB 0.5 2.4 0.18 0.28 0.56 25 45 22.0 0.25 332
33 Inconel 700 250 HB 0.5 2.4 0.18 0.28 0.56 25 45 22.0 0.25 330
34 Stellite 21 350 HB 0.5 2.4 0.18 0.28 0.56 23 40 22.0 0.25 228
36 TiAl6V4 - 0.5 3.2 0.18 0.32 0.64 45 65 22.0 0.30 555
37 T40 - 0.5 2.4 0.18 0.28 0.56 35 55 22.0 0.27 445
38 45 HRc 0.5 2.0 0.10 0.24 0.48 50 100 11.8 0.23 880
38 50 HRc 0.5 1.6 0.10 0.20 0.32 40 90 11.4 0.18 770
38 55 HRc 0.5 1.2 0.10 0.16 0.24 40 80 11.0 0.16 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.6 0.10 0.20 0.32 40 60 11.4 0.16 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.2 0.10 0.16 0.24 30 50 11.0 0.14 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.8 0.18 0.48 1.40 200 400 22.7 0.36 280
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
10
8
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
1C35, Ck45, 1020, 1045, 1060, 28Mn6
St
eel
Non-alloyed
Low alloyed
VNMG 160408 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
137
TURNINGMachining Conditions
VNMG 160408 NN – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 4.0 0.19 0.40 1.44 90 330 22.7 0.34 2240
2 190 HB 0.5 4.0 0.19 0.40 1.44 90 280 22.7 0.32 2220
3 250 HB 0.5 4.0 0.19 0.36 1.20 90 250 22.7 0.30 2200
6 180 HB 0.5 4.0 0.19 0.36 0.96 60 280 22.7 0.29 2200
4,6 230 HB 0.5 3.2 0.19 0.36 0.96 60 250 22.7 0.29 1180
5,7 280 HB 0.5 3.2 0.16 0.32 0.96 60 210 22.7 0.27 1150
8 350 HB 0.5 2.8 0.16 0.32 0.80 60 180 22.4 0.27 1130
10 220 HB 0.5 3.2 0.16 0.32 0.96 35 190 22.3 0.27 1140
10 280 HB 0.5 3.2 0.16 0.32 0.96 35 150 22.3 0.27 1120
11 320 HB 0.5 2.4 0.16 0.28 0.64 35 130 22.0 0.25 1100
11 350 HB 0.5 2.4 0.16 0.28 0.64 35 110 22.0 0.25 990
14 180 HB 0.5 4.0 0.18 0.32 0.96 85 270 22.7 0.23 1190
14 240 HB 0.5 4.0 0.18 0.32 0.80 80 220 22.7 0.20 1170
14 290 HB 0.5 3.2 0.16 0.28 0.64 40 150 22.3 0.22 1100
14 310 HB 0.5 3.2 0.16 0.28 0.64 35 140 22.3 0.22 990
12 200 HB 0.5 4.0 0.16 0.32 0.56 85 250 22.3 0.18 1190
13 42 HRc 0.5 3.2 0.16 0.32 0.56 60 190 22.0 0.18 1130
17,19 150 HB 0.5 4.0 0.14 0.40 1.20 60 250 22.7 0.27 1180
17,19 200 HB 0.5 4.0 0.14 0.40 1.04 60 230 22.7 0.27 1160
18,20 250 HB 0.5 4.0 0.14 0.40 0.96 60 190 22.7 0.27 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
VNMG 160408 NN – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 4.0 0.19 0.40 1.44 180 430 22.7 0.34 2265
2 190 HB 0.5 4.0 0.19 0.40 1.44 180 365 22.7 0.32 2240
3 250 HB 0.5 4.0 0.19 0.36 1.20 180 325 22.7 0.30 2220
6 180 HB 0.5 4.0 0.19 0.36 0.96 120 365 22.7 0.29 2220
4,6 230 HB 0.5 3.2 0.19 0.36 0.96 120 325 22.7 0.29 2200
5,7 280 HB 0.5 3.2 0.16 0.32 0.96 120 275 22.7 0.27 1165
8 350 HB 0.5 2.8 0.16 0.32 0.80 120 235 22.4 0.27 1145
10 220 HB 0.5 3.2 0.16 0.32 0.96 70 245 22.3 0.27 1155
10 280 HB 0.5 3.2 0.16 0.32 0.96 70 195 22.3 0.27 1130
11 320 HB 0.5 2.4 0.16 0.28 0.64 70 170 22.0 0.25 1110
11 350 HB 0.5 2.4 0.16 0.28 0.64 70 145 22.0 0.25 1100
15 150 HB 0.5 4.0 0.14 0.48 1.60 170 325 22.7 0.32 2220
15 200 HB 0.5 4.0 0.14 0.48 1.44 160 300 22.7 0.32 2200
16 250 HB 0.5 4.0 0.14 0.44 1.44 150 275 22.7 0.32 1175
17,19 150 HB 0.5 4.0 0.14 0.40 1.20 120 325 22.7 0.27 2200
17,19 200 HB 0.5 4.0 0.14 0.40 1.04 120 300 22.7 0.27 1175
18,20 250 HB 0.5 4.0 0.14 0.40 0.96 120 245 22.7 0.27 1155
38 45 HRc 0.5 2.0 0.10 0.24 0.48 50 130 11.8 0.23 990
38 50 HRc 0.5 1.6 0.10 0.20 0.32 40 115 11.4 0.18 775
38 55 HRc 0.5 1.2 0.10 0.16 0.24 40 105 00.9 0.16 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.6 0.10 0.20 0.32 40 80 11.4 0.16 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.2 0.10 0.16 0.24 30 65 00.9 0.14 445
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
138
TURNING
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
FProductivity
Shape ToleranceClearance Angle
0°80° m
l
Ø d
s ± 0.13For l = 06, d ± 0.05 m ± 0.08 For l = 08, d ± 0.08 m ± 0.13
Fixing,Chipbreaker
s
F M RInsert Designation s r Catalog Nr.l
LT 1005 Recommended for moderate to high speed
T00028411.204.768WNMA 080412 LT 1005
Strong edge preparation mainly for gray cast iron. For general purpose turning, facing and boring opera-tions.
T00028400.804.768WNMA 080408 LT 1005
Application Guide
LT 1005
VC
Productivity
139
TURNINGMachining Conditions
WNMA 080408 – LT 1005
WNMA 080412 – LT 1005
min max min max min max D.O.C. Feed
15 150 HB 0.7 4.0 0.20 0.60 1.7 270 450 33.5 0.40 3350
15 200 HB 0.7 4.0 0.20 0.58 1.5 200 320 33.5 0.40 2250
16 250 HB 0.7 4.0 0.20 0.56 1.5 170 240 33.5 0.40 2220
17,19 150 HB 0.7 4.0 0.20 0.52 1.3 130 260 33.0 0.30 2240
17,19 200 HB 0.7 4.0 0.20 0.50 1.1 130 230 33.0 0.30 2210
18,20 250 HB 0.7 4.0 0.20 0.48 1.0 130 190 33.0 0.30 1180
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.4 0.14 0.25 0.3 40 60 11.5 0.19 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.8 0.14 0.20 0.3 30 50 11.2 0.17 440
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
11
GGG40, GGG70, 50005
min max min max min max D.O.C. Feed
15 150 HB 0.7 4.0 0.20 0.40 1.4 270 450 33.5 0.32 3350
15 200 HB 0.7 4.0 0.20 0.38 1.2 200 320 33.5 0.32 2250
16 250 HB 0.7 4.0 0.20 0.36 1.2 170 240 33.5 0.32 2220
17,19 150 HB 0.7 4.0 0.20 0.40 1.0 130 260 22.5 0.30 2240
17,19 200 HB 0.7 4.0 0.20 0.38 0.9 130 230 22.5 0.30 2210
18,20 250 HB 0.7 4.0 0.20 0.36 0.8 130 190 22.5 0.30 1180
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.4 0.14 0.20 0.3 40 60 11.4 0.16 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.8 0.14 0.20 0.2 30 50 11.1 0.15 44011
GGG40, GGG70, 50005
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
WNMA
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm]Feed
[mm/rev] Amax[mm2]
Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm]Feed
[mm/rev] Amax[mm2]
Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Cast
Iron
Grey
Malleable & Nodular
H
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Cast
Iron
Grey
Malleable & Nodular
H
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Cast
Iron
Grey
Malleable & Nodular
H
Chilled Cast Iron
White Cast Iron
140
TURNING
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
W N M G
Shape ToleranceClearance Angle Fixing,Chipbreaker
0°80° m
l
Ø d
ss
s ± 0.13For l = 06, d ± 0.05 m ± 0.08 For l = 08, d ± 0.08 m ± 0.13
F M RInsert Designation s r Catalog Nr.l
LT 10 Multi-MatTM General Usage – Standard
T00000771.204.768WNMG 080412 NN LT 10
T00019670.804.768WNMG 080408 NM LT 10
T00000750.804.768WNMG 080408 NN LT 10
T00005840.404.768WNMG 080404 NN LT 10
T00001370.804.766WNMG 060408 NN LT 10
T00001330.404.766WNMG 060404 NN LT 10
Application Guide
F M RInsert Designation s r Catalog Nr.l
LT 1000 Multi-MatTM General Usage - Premium
T00019531.204.768WNMG 080412 NN LT 1000
T00027420.804.768WNMG 080408 NX LT 1000
T00019690.804.768WNMG 080408 NM LT 1000
T00019520.804.768WNMG 080408 NN LT 1000
T00019510.404.768WNMG 080404 NN LT 1000
T00030140.804.766WNMG 060408 NX LT 1000
T00019500.804.766WNMG 060408 NN LT 1000
T00019490.404.766WNMG 060404 NN LT 1000
Application Guide
80° trigon shape inserts with 6 cutting edges. Suitable for all-purpose turning, facing and boring opera-tions.
LT 10 and LT 1000
NX LT 10 and LT 1000 NX LT 10 and LT 1000
LT 10 and LT 1000
NX-CNMP-TNMP-WNMP
Stainless SteelExotic Material Exotic Material
Cutting Conditions!Verify
FProductivity
Stainless Steel
VC
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
141
TURNING
F M RInsert Designation s r Catalog Nr.l
LT 1025 Recommended for moderate to low speed
T00041561.204.768WNMG 080412 NN LT 1025
T00041550.804.768WNMG 080408 NX LT 1025
T00041530.804.768WNMG 080408 NM LT 1025
T00041540.804.768WNMG 080408 NN LT 1025
T00041510.804.766WNMG 060408 NX LT 1025
T00041500.804.766WNMG 060408 NN LT 1025
Application Guide
F M RInsert Designation s r Catalog Nr.l
LT 1005 Recommended for moderate to high speed
T00041051.204.768WNMG 080412 NN LT 1005
T00041040.804.768WNMG 080408 NX LT 1005
T00041020.804.768WNMG 080408 NM LT 1005
T00041030.804.768WNMG 080408 NN LT 1005
T00041000.804.766WNMG 060408 NX LT 1005
T00040990.804.766WNMG 060408 NN LT 1005
Application Guide
NX for LT 1025 LT 1005
NX-CNMP-TNMP-WNMP
Stainless SteelExotic Material VC
Productivity
W N M G
WNMG
142
TURNING Machining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300
2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260
3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240
6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260
4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240
5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200
8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180
10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180
10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140
11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120
11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110
14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260
14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210
14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140
14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140
12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240
13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180
15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240
15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220
16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200
17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240
17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220
18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335
36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660
37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550
38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990
38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880
38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 00.9 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
WNMG 060404 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
143
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 2.5 0.21 0.50 1.17 180 330 22.2 0.35 2240
2 190 HB 0.5 2.5 0.21 0.50 1.17 180 280 22.2 0.35 2220
3 250 HB 0.5 2.5 0.21 0.45 0.98 180 250 22.2 0.35 2200
6 180 HB 0.5 2.5 0.21 0.45 0.78 120 280 22.2 0.32 2200
4,6 230 HB 0.5 2.0 0.21 0.45 0.78 120 250 11.8 0.32 1180
5,7 280 HB 0.5 2.0 0.18 0.40 0.78 120 210 11.8 0.30 1150
8 350 HB 0.5 1.8 0.18 0.40 0.65 120 180 11.6 0.30 1130
10 220 HB 0.5 2.0 0.18 0.40 0.78 70 190 11.8 0.30 1140
10 280 HB 0.5 2.0 0.18 0.40 0.78 70 150 11.8 0.30 1120
11 320 HB 0.5 1.5 0.18 0.35 0.52 70 130 11.5 0.28 1100
11 350 HB 0.5 1.5 0.18 0.35 0.52 70 110 11.5 0.28 990
14 180 HB 0.5 2.5 0.20 0.40 0.78 170 270 22.2 0.35 1190
14 240 HB 0.5 2.5 0.20 0.40 0.65 160 220 22.2 0.32 1170
14 290 HB 0.5 2.0 0.18 0.35 0.52 80 150 11.8 0.28 1100
14 310 HB 0.5 2.0 0.18 0.35 0.52 70 140 11.8 0.28 990
12 200 HB 0.5 2.5 0.22 0.40 0.65 170 250 22.2 0.32 1190
13 42 HRc 0.5 2.0 0.22 0.40 0.65 120 190 22.0 0.32 1130
15 150 HB 0.5 2.5 0.15 0.60 1.30 170 250 22.2 0.35 2200
15 200 HB 0.5 2.5 0.15 0.60 1.17 160 230 22.2 0.35 1180
16 250 HB 0.5 2.5 0.15 0.55 1.17 150 210 22.2 0.35 1160
17,19 150 HB 0.5 2.5 0.15 0.50 0.98 120 250 22.2 0.30 1180
17,19 200 HB 0.5 2.5 0.15 0.50 0.85 120 230 22.2 0.30 1160
18,20 250 HB 0.5 2.5 0.15 0.50 0.78 120 190 22.2 0.30 1140
31,32 Incoloy 800 240 HB 0.5 1.5 0.20 0.35 0.46 25 45 11.5 0.28 332
33 Inconel 700 250 HB 0.5 1.5 0.20 0.35 0.46 25 45 11.5 0.28 330
34 Stellite 21 350 HB 0.5 1.5 0.20 0.35 0.46 23 40 11.5 0.28 228
36 TiAl6V4 - 0.5 2.0 0.20 0.40 0.52 45 65 11.5 0.33 555
37 T40 - 0.5 1.5 0.20 0.35 0.46 35 55 11.5 0.30 445
38 45 HRc 0.5 1.6 0.11 0.30 0.39 50 100 11.5 0.25 880
38 50 HRc 0.5 1.3 0.11 0.25 0.26 40 90 11.0 0.20 770
38 55 HRc 0.5 1.3 0.11 0.20 0.20 40 80 11.0 0.18 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.3 0.11 0.25 0.26 40 60 11.0 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.3 0.11 0.20 0.20 30 50 11.0 0.15 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.0 0.20 0.60 1.80 200 400 22.2 0.40 280
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
WNMG 060408 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
144
TURNING Machining Conditions
WNMG 060408 NN – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 2.5 0.21 0.50 1.17 90 330 11.8 0.38 2240
2 190 HB 0.5 2.5 0.21 0.50 1.17 90 280 11.8 0.35 2220
3 250 HB 0.5 2.5 0.21 0.45 0.98 90 250 11.8 0.33 2200
6 180 HB 0.5 2.5 0.21 0.45 0.78 60 280 11.8 0.32 2200
4,6 230 HB 0.5 2.0 0.21 0.45 0.78 60 250 11.8 0.32 1180
5,7 280 HB 0.5 2.0 0.18 0.40 0.78 60 210 11.8 0.30 1150
8 350 HB 0.5 1.8 0.18 0.40 0.65 60 180 11.6 0.30 1130
10 220 HB 0.5 2.0 0.18 0.40 0.78 35 190 11.5 0.30 1140
10 280 HB 0.5 2.0 0.18 0.40 0.78 35 150 11.5 0.30 1120
11 320 HB 0.5 1.5 0.18 0.35 0.52 35 130 11.3 0.28 1100
11 350 HB 0.5 1.5 0.18 0.35 0.52 35 110 11.3 0.28 990
14 180 HB 0.5 2.5 0.20 0.40 0.78 85 270 11.8 0.25 1190
14 240 HB 0.5 2.5 0.20 0.40 0.65 80 220 11.8 0.22 1170
14 290 HB 0.5 2.0 0.18 0.35 0.52 40 150 11.5 0.24 1100
14 310 HB 0.5 2.0 0.18 0.35 0.52 35 140 11.5 0.24 990
12 200 HB 0.5 2.5 0.18 0.40 0.46 85 250 11.5 0.20 1190
13 42 HRc 0.5 2.0 0.18 0.40 0.46 60 190 11.3 0.20 1130
17,19 150 HB 0.5 2.5 0.15 0.50 0.98 60 250 11.8 0.30 1180
17,19 200 HB 0.5 2.5 0.15 0.50 0.85 60 230 11.8 0.30 1160
18,20 250 HB 0.5 2.5 0.15 0.50 0.78 60 190 11.8 0.30 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
WNMG 060408 NN – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 2.5 0.21 0.50 1.17 180 430 11.8 0.38 2265
2 190 HB 0.5 2.5 0.21 0.50 1.17 180 365 11.8 0.35 2240
3 250 HB 0.5 2.5 0.21 0.45 0.98 180 325 11.8 0.33 2220
6 180 HB 0.5 2.5 0.21 0.45 0.78 120 365 11.8 0.32 2220
4,6 230 HB 0.5 2.0 0.21 0.45 0.78 120 325 11.8 0.32 2200
5,7 280 HB 0.5 2.0 0.18 0.40 0.78 120 275 11.8 0.30 1165
8 350 HB 0.5 1.8 0.18 0.40 0.65 120 235 11.6 0.30 1145
10 220 HB 0.5 2.0 0.18 0.40 0.78 70 245 11.5 0.30 1155
10 280 HB 0.5 2.0 0.18 0.40 0.78 70 195 11.5 0.30 1130
11 320 HB 0.5 1.5 0.18 0.35 0.52 70 170 11.3 0.28 1110
11 350 HB 0.5 1.5 0.18 0.35 0.52 70 145 11.3 0.28 1100
15 150 HB 0.5 2.5 0.15 0.60 1.30 170 325 11.8 0.35 2220
15 200 HB 0.5 2.5 0.15 0.60 1.17 160 300 11.8 0.35 2200
16 250 HB 0.5 2.5 0.15 0.55 1.17 150 275 11.8 0.35 1175
17,19 150 HB 0.5 2.5 0.15 0.50 0.98 120 325 11.8 0.30 2200
17,19 200 HB 0.5 2.5 0.15 0.50 0.85 120 300 11.8 0.30 1175
18,20 250 HB 0.5 2.5 0.15 0.50 0.78 120 245 11.8 0.30 1155
38 45 HRc 0.5 1.3 0.11 0.30 0.39 50 130 11.2 0.25 990
38 50 HRc 0.5 1.0 0.11 0.25 0.26 40 115 00.9 0.20 775
38 55 HRc 0.5 0.8 0.11 0.20 0.20 40 105 00.6 0.18 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.0 0.11 0.25 0.26 40 80 00.9 0.18 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 0.8 0.11 0.20 0.20 30 65 00.6 0.15 445
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
7 GG20, GG40, EN-GJL-250,
No30B
8
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
145
TURNINGMachining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 2.5 0.18 0.50 1.13 180 330 11.8 0.36 2240
2 190 HB 0.5 2.5 0.18 0.50 1.13 180 280 11.8 0.33 2220
3 250 HB 0.5 2.5 0.18 0.45 0.95 180 250 11.8 0.31 2200
6 180 HB 0.5 2.5 0.18 0.45 0.76 120 280 11.8 0.30 2200
4,6 230 HB 0.5 2.0 0.18 0.45 0.76 120 250 11.8 0.30 1180
5,7 280 HB 0.5 2.0 0.16 0.40 0.76 120 210 11.8 0.29 1150
8 350 HB 0.5 1.8 0.16 0.40 0.63 120 180 11.6 0.29 1130
10 220 HB 0.5 2.0 0.16 0.40 0.76 70 190 11.5 0.29 1140
10 280 HB 0.5 2.0 0.16 0.40 0.76 70 150 11.5 0.29 1120
11 320 HB 0.5 1.5 0.16 0.35 0.50 70 130 11.3 0.27 1100
11 350 HB 0.5 1.5 0.16 0.35 0.50 70 110 11.3 0.27 990
14 180 HB 0.5 2.5 0.18 0.40 0.76 170 270 11.8 0.24 1190
14 240 HB 0.5 2.5 0.18 0.40 0.63 160 220 11.8 0.21 1170
14 290 HB 0.5 2.0 0.16 0.35 0.50 80 150 11.5 0.23 1100
14 310 HB 0.5 2.0 0.16 0.35 0.50 70 140 11.5 0.23 990
12 200 HB 0.5 2.5 0.16 0.40 0.44 170 250 11.5 0.19 1190
13 42 HRc 0.5 2.0 0.16 0.40 0.44 120 190 11.3 0.19 1130
15 150 HB 0.5 2.5 0.13 0.60 1.26 170 250 11.8 0.33 2200
15 200 HB 0.5 2.5 0.13 0.60 1.13 160 230 11.8 0.33 1180
16 250 HB 0.5 2.5 0.13 0.55 1.13 150 210 11.8 0.33 1160
17,19 150 HB 0.5 2.5 0.13 0.50 0.95 120 250 11.8 0.29 1180
17,19 200 HB 0.5 2.5 0.13 0.50 0.82 120 230 11.8 0.29 1160
18,20 250 HB 0.5 2.5 0.13 0.50 0.76 120 190 11.8 0.29 1140
31,32 Incoloy 800 240 HB 0.5 1.5 0.18 0.35 0.44 25 45 11.2 0.27 330
33 Inconel 700 250 HB 0.5 1.5 0.18 0.35 0.44 25 45 11.2 0.27 330
34 Stellite 21 350 HB 0.5 1.5 0.18 0.35 0.44 25 40 11.2 0.27 330
36 TiAl6V4 - 0.5 1.8 0.18 0.40 0.50 45 65 11.2 0.31 555
37 T40 - 0.5 1.5 0.18 0.35 0.44 35 55 11.2 0.29 445
38 45 HRc 0.5 1.3 0.10 0.30 0.38 50 100 11.2 0.24 880
38 50 HRc 0.5 1.0 0.10 0.25 0.25 40 90 00.9 0.19 770
38 55 HRc 0.5 0.8 0.10 0.20 0.19 40 80 00.6 0.17 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.0 0.10 0.25 0.25 40 60 00.9 0.17 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 0.8 0.10 0.20 0.19 30 50 00.6 0.14 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.0 0.18 0.60 1.13 200 400 1.8 0.38 280
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
WNMG 060408 NX – LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
146
TURNING Machining Conditions
WNMG 060408 NX – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 2.5 0.18 0.50 1.13 90 330 11.8 0.36 2240
2 190 HB 0.5 2.5 0.18 0.50 1.13 90 280 11.8 0.33 2220
3 250 HB 0.5 2.5 0.18 0.45 0.95 90 250 11.8 0.31 2200
6 180 HB 0.5 2.5 0.18 0.45 0.76 60 280 11.8 0.30 2200
4,6 230 HB 0.5 2.0 0.18 0.45 0.76 60 250 11.8 0.30 1180
5,7 280 HB 0.5 2.0 0.16 0.40 0.76 60 210 11.8 0.29 1150
8 350 HB 0.5 1.8 0.16 0.40 0.63 60 180 11.6 0.29 1130
10 220 HB 0.5 2.0 0.16 0.40 0.76 35 190 11.5 0.29 1140
10 280 HB 0.5 2.0 0.16 0.40 0.76 35 150 11.5 0.29 1120
11 320 HB 0.5 1.5 0.16 0.35 0.50 35 130 11.3 0.27 1100
11 350 HB 0.5 1.5 0.16 0.35 0.50 35 110 11.3 0.27 990
14 180 HB 0.5 2.5 0.18 0.40 0.76 85 270 11.8 0.24 1190
14 240 HB 0.5 2.5 0.18 0.40 0.63 80 220 11.8 0.21 1170
14 290 HB 0.5 2.0 0.16 0.35 0.50 40 150 11.5 0.23 1100
14 310 HB 0.5 2.0 0.16 0.35 0.50 35 140 11.5 0.23 990
12 200 HB 0.5 2.5 0.16 0.40 0.44 85 250 11.5 0.19 1190
13 42 HRc 0.5 2.0 0.16 0.40 0.44 60 190 11.3 0.19 1130
17,19 150 HB 0.5 2.5 0.13 0.50 0.95 60 250 11.8 0.29 1180
17,19 200 HB 0.5 2.5 0.13 0.50 0.82 60 230 11.8 0.29 1160
18,20 250 HB 0.5 2.5 0.13 0.50 0.76 60 190 11.8 0.29 1140
GGG40, GGG70, 50005
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
WNMG 060408 NX – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 2.5 0.18 0.50 1.13 180 430 11.8 0.36 2265
2 190 HB 0.5 2.5 0.18 0.50 1.13 180 365 11.8 0.33 2240
3 250 HB 0.5 2.5 0.18 0.45 0.95 180 325 11.8 0.31 2220
6 180 HB 0.5 2.5 0.18 0.45 0.76 120 365 11.8 0.30 2220
4,6 230 HB 0.5 2.0 0.18 0.45 0.76 120 325 11.8 0.30 2200
5,7 280 HB 0.5 2.0 0.16 0.40 0.76 120 275 11.8 0.29 1165
8 350 HB 0.5 1.8 0.16 0.40 0.63 120 235 11.6 0.29 1145
10 220 HB 0.5 2.0 0.16 0.40 0.76 70 245 11.5 0.29 1155
10 280 HB 0.5 2.0 0.16 0.40 0.76 70 195 11.5 0.29 1130
11 320 HB 0.5 1.5 0.16 0.35 0.50 70 170 11.3 0.27 1110
11 350 HB 0.5 1.5 0.16 0.35 0.50 70 145 11.3 0.27 1100
15 150 HB 0.5 2.5 0.13 0.60 1.26 170 325 11.8 0.33 2220
15 200 HB 0.5 2.5 0.13 0.60 1.13 160 300 11.8 0.33 2200
16 250 HB 0.5 2.5 0.13 0.55 1.13 150 275 11.8 0.33 1175
17,19 150 HB 0.5 2.5 0.13 0.50 0.95 120 325 11.8 0.29 2200
17,19 200 HB 0.5 2.5 0.13 0.50 0.82 120 300 11.8 0.29 1175
18,20 250 HB 0.5 2.5 0.13 0.50 0.76 120 245 11.8 0.29 1155
38 45 HRc 0.5 1.3 0.10 0.30 0.38 50 130 11.2 0.24 990
38 50 HRc 0.5 1.0 0.10 0.25 0.25 40 115 00.9 0.19 775
38 55 HRc 0.5 0.8 0.10 0.20 0.19 40 105 00.6 0.17 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.0 0.10 0.25 0.25 40 80 00.9 0.17 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 0.8 0.10 0.20 0.19 30 65 00.6 0.14 445
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
147
TURNINGMachining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300
2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260
3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240
6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260
4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240
5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200
8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180
10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180
10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140
11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120
11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110
14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260
14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210
14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140
14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140
12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240
13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180
15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240
15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220
16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200
17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240
17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220
18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335
36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660
37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550
38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990
38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880
38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 00.9 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
WNMG 080404 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
148
TURNING Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 3.5 0.25 0.65 2.16 180 330 33.0 0.44 2240
2 190 HB 0.5 3.5 0.25 0.65 2.16 180 280 33.0 0.44 2220
3 250 HB 0.5 3.5 0.25 0.59 1.80 180 250 33.0 0.44 2200
6 180 HB 0.5 3.5 0.25 0.59 1.44 120 280 33.0 0.40 2200
4,6 230 HB 0.5 2.8 0.25 0.59 1.44 120 250 33.0 0.40 1180
5,7 280 HB 0.5 2.8 0.22 0.52 1.44 120 210 33.0 0.38 1150
8 350 HB 0.5 2.5 0.22 0.52 1.20 120 180 33.0 0.38 1130
10 220 HB 0.5 2.8 0.22 0.52 1.44 70 190 22.5 0.38 1140
10 280 HB 0.5 2.8 0.22 0.52 1.44 70 150 22.5 0.38 1120
11 320 HB 0.5 2.1 0.22 0.46 0.96 70 130 22.5 0.35 1100
11 350 HB 0.5 2.1 0.22 0.46 0.96 70 110 22.5 0.35 990
14 180 HB 0.5 3.5 0.24 0.52 1.44 170 270 33.0 0.44 1190
14 240 HB 0.5 3.5 0.24 0.52 1.20 160 220 33.0 0.40 1170
14 290 HB 0.5 2.8 0.22 0.46 0.96 80 150 22.5 0.35 1100
14 310 HB 0.5 2.8 0.22 0.46 0.96 70 140 22.5 0.35 990
12 200 HB 0.5 3.5 0.26 0.52 1.20 170 250 33.0 0.40 1190
13 42 HRc 0.5 2.8 0.26 0.52 1.20 120 190 22.5 0.40 1130
15 150 HB 0.5 3.5 0.18 0.78 2.40 170 250 33.0 0.44 2200
15 200 HB 0.5 3.5 0.18 0.78 2.16 160 230 33.0 0.44 1180
16 250 HB 0.5 3.5 0.18 0.72 2.16 150 210 33.0 0.44 1160
17,19 150 HB 0.5 3.5 0.18 0.65 1.80 120 250 33.0 0.38 1180
17,19 200 HB 0.5 3.5 0.18 0.65 1.56 120 230 33.0 0.38 1160
18,20 250 HB 0.5 3.5 0.18 0.65 1.44 120 190 33.0 0.38 1140
31,32 Incoloy 800 240 HB 0.5 2.1 0.24 0.46 0.84 25 45 22.0 0.35 332
33 Inconel 700 250 HB 0.5 2.1 0.24 0.46 0.84 25 45 22.0 0.35 330
34 Stellite 21 350 HB 0.5 2.1 0.24 0.46 0.84 23 40 22.0 0.35 228
36 TiAl6V4 - 0.5 2.8 0.24 0.52 0.96 45 65 22.0 0.41 555
37 T40 - 0.5 2.1 0.24 0.46 0.84 35 55 22.0 0.38 445
38 45 HRc 0.5 1.8 0.13 0.39 0.72 50 100 22.0 0.31 880
38 50 HRc 0.5 1.5 0.13 0.33 0.48 40 90 11.5 0.25 770
38 55 HRc 0.5 1.5 0.13 0.26 0.36 40 80 11.0 0.23 660Chilled Cast
IIron40 Ni-Hard 2 400 HB 0.5 1.5 0.13 0.33 0.48 40 60 11.5 0.23 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.13 0.26 0.36 30 50 11.0 0.19 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.2 0.24 0.78 2.20 200 400 33.0 0.50 280
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
8
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic
6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
WNMG 080408 NM – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
149
TURNINGMachining Conditions
WNMG 080408 NM – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 3.5 0.25 0.65 2.16 90 330 22.6 0.48 2240
2 190 HB 0.5 3.5 0.25 0.65 2.16 90 280 22.6 0.44 2220
3 250 HB 0.5 3.5 0.25 0.59 1.80 90 250 22.6 0.41 2200
6 180 HB 0.5 3.5 0.25 0.59 1.44 60 280 22.6 0.40 2200
4,6 230 HB 0.5 2.8 0.25 0.59 1.44 60 250 22.6 0.40 1180
5,7 280 HB 0.5 2.8 0.22 0.52 1.44 60 210 22.6 0.38 1150
8 350 HB 0.5 2.5 0.22 0.52 1.20 60 180 22.3 0.38 1130
10 220 HB 0.5 2.8 0.22 0.52 1.44 35 190 22.1 0.38 1140
10 280 HB 0.5 2.8 0.22 0.52 1.44 35 150 22.1 0.38 1120
11 320 HB 0.5 2.1 0.22 0.46 0.96 35 130 11.9 0.35 1100
11 350 HB 0.5 2.1 0.22 0.46 0.96 35 110 11.9 0.35 990
14 180 HB 0.5 3.5 0.24 0.52 1.44 85 270 22.6 0.31 1190
14 240 HB 0.5 3.5 0.24 0.52 1.20 80 220 22.6 0.28 1170
14 290 HB 0.5 2.8 0.22 0.46 0.96 40 150 22.1 0.30 1100
14 310 HB 0.5 2.8 0.22 0.46 0.96 35 140 22.1 0.30 990
12 200 HB 0.5 3.5 0.22 0.52 0.84 85 250 22.1 0.25 1190
13 42 HRc 0.5 2.8 0.22 0.52 0.84 60 190 11.9 0.25 1130
17,19 150 HB 0.5 3.5 0.18 0.65 1.80 60 250 22.6 0.38 1180
17,19 200 HB 0.5 3.5 0.18 0.65 1.56 60 230 22.6 0.38 1160
18,20 250 HB 0.5 3.5 0.18 0.65 1.44 60 190 22.6 0.38 1140
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Malleable & Nodular 8GGG40, GGG70,
50005
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
WNMG 080408 NM – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 3.5 0.25 0.65 2.16 180 430 22.6 0.48 2265
2 190 HB 0.5 3.5 0.25 0.65 2.16 180 365 22.6 0.44 2240
3 250 HB 0.5 3.5 0.25 0.59 1.80 180 325 22.6 0.41 2220
6 180 HB 0.5 3.5 0.25 0.59 1.44 120 365 22.6 0.40 2220
4,6 230 HB 0.5 2.8 0.25 0.59 1.44 120 325 22.6 0.40 2200
5,7 280 HB 0.5 2.8 0.22 0.52 1.44 120 275 22.6 0.38 1165
8 350 HB 0.5 2.5 0.22 0.52 1.20 120 235 22.3 0.38 1145
10 220 HB 0.5 2.8 0.22 0.52 1.44 70 245 22.1 0.38 1155
10 280 HB 0.5 2.8 0.22 0.52 1.44 70 195 22.1 0.38 1130
11 320 HB 0.5 2.1 0.22 0.46 0.96 70 170 11.9 0.35 1110
11 350 HB 0.5 2.1 0.22 0.46 0.96 70 145 11.9 0.35 1100
15 150 HB 0.5 3.5 0.18 0.78 2.40 170 325 22.6 0.44 2220
15 200 HB 0.5 3.5 0.18 0.78 2.16 160 300 22.6 0.44 2200
16 250 HB 0.5 3.5 0.18 0.72 2.16 150 275 22.6 0.44 1175
17,19 150 HB 0.5 3.5 0.18 0.65 1.80 120 325 22.6 0.38 2200
17,19 200 HB 0.5 3.5 0.18 0.65 1.56 120 300 22.6 0.38 1175
18,20 250 HB 0.5 3.5 0.18 0.65 1.44 120 245 22.6 0.38 1155
38 45 HRc 0.5 1.8 0.13 0.39 0.72 50 130 11.7 0.31 990
38 50 HRc 0.5 1.4 0.13 0.33 0.48 40 115 11.3 0.25 775
38 55 HRc 0.5 1.1 0.13 0.26 0.36 40 105 00.9 0.23 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.4 0.13 0.33 0.48 40 80 11.3 0.23 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.1 0.13 0.26 0.36 30 65 00.9 0.19 445
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
150
TURNING Machining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 3.5 0.21 0.50 1.80 180 330 22.4 0.35 2240
2 190 HB 0.5 3.5 0.21 0.50 1.80 180 280 22.4 0.35 2220
3 250 HB 0.5 3.5 0.21 0.45 1.50 180 250 22.4 0.35 2200
6 180 HB 0.5 3.5 0.21 0.45 1.20 120 280 22.4 0.32 2200
4,6 230 HB 0.5 2.8 0.21 0.45 1.20 120 250 22.4 0.32 1180
5,7 280 HB 0.5 2.8 0.18 0.40 1.20 120 210 22.4 0.30 1150
8 350 HB 0.5 2.5 0.18 0.40 1.00 120 180 22.4 0.30 1130
10 220 HB 0.5 2.8 0.18 0.40 1.20 70 190 22.0 0.30 1140
10 280 HB 0.5 2.8 0.18 0.40 1.20 70 150 22.0 0.30 1120
11 320 HB 0.5 2.1 0.18 0.35 0.80 70 130 22.0 0.28 1100
11 350 HB 0.5 2.1 0.18 0.35 0.80 70 110 22.0 0.28 990
14 180 HB 0.5 3.5 0.20 0.40 1.20 170 270 22.4 0.35 1190
14 240 HB 0.5 3.5 0.20 0.40 1.00 160 220 22.4 0.32 1170
14 290 HB 0.5 2.8 0.18 0.35 0.80 80 150 22.0 0.28 1100
14 310 HB 0.5 2.8 0.18 0.35 0.80 70 140 22.0 0.28 990
12 200 HB 0.5 3.5 0.22 0.40 1.00 170 250 22.4 0.32 1190
13 42 HRc 0.5 2.8 0.22 0.40 1.00 120 190 22.0 0.32 1130
15 150 HB 0.5 3.5 0.15 0.60 2.00 170 250 22.4 0.35 2200
15 200 HB 0.5 3.5 0.15 0.60 1.80 160 230 22.4 0.35 1180
16 250 HB 0.5 3.5 0.15 0.55 1.80 150 210 22.4 0.35 1160
17,19 150 HB 0.5 3.5 0.15 0.50 1.50 120 250 22.4 0.30 1180
17,19 200 HB 0.5 3.5 0.15 0.50 1.30 120 230 22.4 0.30 1160
18,20 250 HB 0.5 3.5 0.15 0.50 1.20 120 190 22.4 0.30 1140
31,32 Incoloy 800 240 HB 0.5 2.1 0.20 0.35 0.70 25 45 11.6 0.28 332
33 Inconel 700 250 HB 0.5 2.1 0.20 0.35 0.70 25 45 11.6 0.28 330
34 Stellite 21 350 HB 0.5 2.1 0.20 0.35 0.70 23 40 11.6 0.28 228
36 TiAl6V4 - 0.5 2.8 0.20 0.40 0.80 45 65 11.6 0.33 555
37 T40 - 0.5 2.1 0.20 0.35 0.70 35 55 11.6 0.30 445
38 45 HRc 0.5 1.8 0.11 0.30 0.60 50 100 11.6 0.25 880
38 50 HRc 0.5 1.5 0.11 0.25 0.40 40 90 11.2 0.20 770
38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 00.8 0.18 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.5 0.11 0.25 0.40 40 60 11.2 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.11 0.20 0.30 30 50 00.8 0.15 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.2 0.20 0.60 1.80 200 400 2.4 0.40 280
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
WNMG 080408 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
151
TURNINGMachining Conditions
WNMG 080408 NN – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 3.5 0.21 0.50 1.80 90 330 22.4 0.38 2240
2 190 HB 0.5 3.5 0.21 0.50 1.80 90 280 22.4 0.35 2220
3 250 HB 0.5 3.5 0.21 0.45 1.50 90 250 22.4 0.33 2200
6 180 HB 0.5 3.5 0.21 0.45 1.20 60 280 22.4 0.32 2200
4,6 230 HB 0.5 2.8 0.21 0.45 1.20 60 250 22.4 0.32 1180
5,7 280 HB 0.5 2.8 0.18 0.40 1.20 60 210 22.4 0.30 1150
8 350 HB 0.5 2.5 0.18 0.40 1.00 60 180 22.2 0.30 1130
10 220 HB 0.5 2.8 0.18 0.40 1.20 35 190 22.0 0.30 1140
10 280 HB 0.5 2.8 0.18 0.40 1.20 35 150 22.0 0.30 1120
11 320 HB 0.5 2.1 0.18 0.35 0.80 35 130 11.8 0.28 1100
11 350 HB 0.5 2.1 0.18 0.35 0.80 35 110 11.8 0.28 990
14 180 HB 0.5 3.5 0.20 0.40 1.20 85 270 22.4 0.25 1190
14 240 HB 0.5 3.5 0.20 0.40 1.00 80 220 22.4 0.22 1170
14 290 HB 0.5 2.8 0.18 0.35 0.80 40 150 22.0 0.24 1100
14 310 HB 0.5 2.8 0.18 0.35 0.80 35 140 22.0 0.24 990
12 200 HB 0.5 3.5 0.18 0.40 0.70 85 250 22.0 0.20 1190
13 42 HRc 0.5 2.8 0.18 0.40 0.70 60 190 11.8 0.20 1130
17,19 150 HB 0.5 3.5 0.15 0.50 1.50 60 250 22.4 0.30 1180
17,19 200 HB 0.5 3.5 0.15 0.50 1.30 60 230 22.4 0.30 1160
18,20 250 HB 0.5 3.5 0.15 0.50 1.20 60 190 22.4 0.30 1140
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Malleable & Nodular 8GGG40, GGG70,
50005
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
WNMG 080408 NN – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 3.5 0.21 0.50 1.80 180 430 22.4 0.38 2265
2 190 HB 0.5 3.5 0.21 0.50 1.80 180 365 22.4 0.35 2240
3 250 HB 0.5 3.5 0.21 0.45 1.50 180 325 22.4 0.33 2220
6 180 HB 0.5 3.5 0.21 0.45 1.20 120 365 22.4 0.32 2220
4,6 230 HB 0.5 2.8 0.21 0.45 1.20 120 325 22.4 0.32 2200
5,7 280 HB 0.5 2.8 0.18 0.40 1.20 120 275 22.4 0.30 1165
8 350 HB 0.5 2.5 0.18 0.40 1.00 120 235 22.2 0.30 1145
10 220 HB 0.5 2.8 0.18 0.40 1.20 70 245 22.0 0.30 1155
10 280 HB 0.5 2.8 0.18 0.40 1.20 70 195 22.0 0.30 1130
11 320 HB 0.5 2.1 0.18 0.35 0.80 70 170 11.8 0.28 1110
11 350 HB 0.5 2.1 0.18 0.35 0.80 70 145 11.8 0.28 1100
15 150 HB 0.5 3.5 0.15 0.60 2.00 170 325 22.4 0.35 2220
15 200 HB 0.5 3.5 0.15 0.60 1.80 160 300 22.4 0.35 2200
16 250 HB 0.5 3.5 0.15 0.55 1.80 150 275 22.4 0.35 1175
17,19 150 HB 0.5 3.5 0.15 0.50 1.50 120 325 22.4 0.30 2200
17,19 200 HB 0.5 3.5 0.15 0.50 1.30 120 300 22.4 0.30 1175
18,20 250 HB 0.5 3.5 0.15 0.50 1.20 120 245 22.4 0.30 1155
38 45 HRc 0.5 1.8 0.11 0.30 0.60 50 130 11.6 0.25 990
38 50 HRc 0.5 1.4 0.11 0.25 0.40 40 115 11.2 0.20 775
38 55 HRc 0.5 1.1 0.11 0.20 0.30 40 105 00.8 0.18 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.4 0.11 0.25 0.40 40 80 11.2 0.18 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.1 0.11 0.20 0.30 30 65 00.8 0.15 445
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
152
TURNING Machining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 3.5 0.18 0.50 1.71 180 330 22.4 0.36 2240
2 190 HB 0.5 3.5 0.18 0.50 1.71 180 280 22.4 0.33 2220
3 250 HB 0.5 3.5 0.18 0.45 1.43 180 250 22.4 0.31 2200
6 180 HB 0.5 3.5 0.18 0.45 1.14 120 280 22.4 0.30 2200
4,6 230 HB 0.5 2.8 0.18 0.45 1.14 120 250 22.4 0.30 1180
5,7 280 HB 0.5 2.8 0.16 0.40 1.14 120 210 22.4 0.29 1150
8 350 HB 0.5 2.5 0.16 0.40 0.95 120 180 22.2 0.29 1130
10 220 HB 0.5 2.8 0.16 0.40 1.14 70 190 22.0 0.29 1140
10 280 HB 0.5 2.8 0.16 0.40 1.14 70 150 22.0 0.29 1120
11 320 HB 0.5 2.1 0.16 0.35 0.76 70 130 11.8 0.27 1100
11 350 HB 0.5 2.1 0.16 0.35 0.76 70 110 11.8 0.27 990
14 180 HB 0.5 3.5 0.18 0.40 1.14 170 270 22.4 0.24 1190
14 240 HB 0.5 3.5 0.18 0.40 0.95 160 220 22.4 0.21 1170
14 290 HB 0.5 2.8 0.16 0.35 0.76 80 150 22.0 0.23 1100
14 310 HB 0.5 2.8 0.16 0.35 0.76 70 140 22.0 0.23 990
12 200 HB 0.5 3.5 0.16 0.40 0.67 170 250 22.0 0.19 1190
13 42 HRc 0.5 2.8 0.16 0.40 0.67 120 190 11.8 0.19 1130
15 150 HB 0.5 3.5 0.13 0.60 1.90 170 250 22.4 0.33 2200
15 200 HB 0.5 3.5 0.13 0.60 1.71 160 230 22.4 0.33 1180
16 250 HB 0.5 3.5 0.13 0.55 1.71 150 210 22.4 0.33 1160
17,19 150 HB 0.5 3.5 0.13 0.50 1.43 120 250 22.4 0.29 1180
17,19 200 HB 0.5 3.5 0.13 0.50 1.24 120 230 22.4 0.29 1160
18,20 250 HB 0.5 3.5 0.13 0.50 1.14 120 190 22.4 0.29 1140
31,32 Incoloy 800 240 HB 0.5 2.1 0.18 0.35 0.67 25 45 11.6 0.27 330
33 Inconel 700 250 HB 0.5 2.1 0.18 0.35 0.67 25 45 11.6 0.27 330
34 Stellite 21 350 HB 0.5 2.1 0.18 0.35 0.67 25 40 11.6 0.27 330
36 TiAl6V4 - 0.5 2.5 0.18 0.40 0.76 45 65 11.6 0.31 555
37 T40 - 0.5 2.1 0.18 0.35 0.67 35 55 11.6 0.29 445
38 45 HRc 0.5 1.8 0.10 0.30 0.57 50 100 11.6 0.24 880
38 50 HRc 0.5 1.4 0.10 0.25 0.38 40 90 11.2 0.19 770
38 55 HRc 0.5 1.1 0.10 0.20 0.29 40 80 00.8 0.17 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.4 0.10 0.25 0.38 40 60 11.2 0.17 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.1 0.10 0.20 0.29 30 50 00.8 0.14 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.2 0.18 0.60 1.71 200 400 2.4 0.38 280
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
1C35, Ck45, 1020, 1045, 1060, 28Mn6
D.O.C. [mm]
2
Gr. N°VDI
GroupMaterial Examples* Hardness
WNMG 080408 NX – LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
153
TURNINGMachining Conditions
WNMG 080408 NX – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 3.5 0.18 0.50 1.71 90 330 22.4 0.36 2240
2 190 HB 0.5 3.5 0.18 0.50 1.71 90 280 22.4 0.33 2220
3 250 HB 0.5 3.5 0.18 0.45 1.43 90 250 22.4 0.31 2200
6 180 HB 0.5 3.5 0.18 0.45 1.14 60 280 22.4 0.30 2200
4,6 230 HB 0.5 2.8 0.18 0.45 1.14 60 250 22.4 0.30 1180
5,7 280 HB 0.5 2.8 0.16 0.40 1.14 60 210 22.4 0.29 1150
8 350 HB 0.5 2.5 0.16 0.40 0.95 60 180 22.2 0.29 1130
10 220 HB 0.5 2.8 0.16 0.40 1.14 35 190 22.0 0.29 1140
10 280 HB 0.5 2.8 0.16 0.40 1.14 35 150 22.0 0.29 1120
11 320 HB 0.5 2.1 0.16 0.35 0.76 35 130 11.8 0.27 1100
11 350 HB 0.5 2.1 0.16 0.35 0.76 35 110 11.8 0.27 990
14 180 HB 0.5 3.5 0.18 0.40 1.14 85 270 22.4 0.24 1190
14 240 HB 0.5 3.5 0.18 0.40 0.95 80 220 22.4 0.21 1170
14 290 HB 0.5 2.8 0.16 0.35 0.76 40 150 22.0 0.23 1100
14 310 HB 0.5 2.8 0.16 0.35 0.76 35 140 22.0 0.23 990
12 200 HB 0.5 3.5 0.16 0.40 0.67 85 250 22.0 0.19 1190
13 42 HRc 0.5 2.8 0.16 0.40 0.67 60 190 11.8 0.19 1130
17,19 150 HB 0.5 3.5 0.13 0.50 1.43 60 250 22.4 0.29 1180
17,19 200 HB 0.5 3.5 0.13 0.50 1.24 60 230 22.4 0.29 1160
18,20 250 HB 0.5 3.5 0.13 0.50 1.14 60 190 22.4 0.29 1140
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Malleable & Nodular 8GGG40, GGG70,
50005
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
WNMG 080408 NX – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 3.5 0.18 0.50 1.71 180 430 22.4 0.36 2265
2 190 HB 0.5 3.5 0.18 0.50 1.71 180 365 22.4 0.33 2240
3 250 HB 0.5 3.5 0.18 0.45 1.43 180 325 22.4 0.31 2220
6 180 HB 0.5 3.5 0.18 0.45 1.14 120 365 22.4 0.30 2220
4,6 230 HB 0.5 2.8 0.18 0.45 1.14 120 325 22.4 0.30 2200
5,7 280 HB 0.5 2.8 0.16 0.40 1.14 120 275 22.4 0.29 1165
8 350 HB 0.5 2.5 0.16 0.40 0.95 120 235 22.2 0.29 1145
10 220 HB 0.5 2.8 0.16 0.40 1.14 70 245 22.0 0.29 1155
10 280 HB 0.5 2.8 0.16 0.40 1.14 70 195 22.0 0.29 1130
11 320 HB 0.5 2.1 0.16 0.35 0.76 70 170 11.8 0.27 1110
11 350 HB 0.5 2.1 0.16 0.35 0.76 70 145 11.8 0.27 1100
15 150 HB 0.5 3.5 0.13 0.60 1.90 170 325 22.4 0.33 2220
15 200 HB 0.5 3.5 0.13 0.60 1.71 160 300 22.4 0.33 2200
16 250 HB 0.5 3.5 0.13 0.55 1.71 150 275 22.4 0.33 1175
17,19 150 HB 0.5 3.5 0.13 0.50 1.43 120 325 22.4 0.29 2200
17,19 200 HB 0.5 3.5 0.13 0.50 1.24 120 300 22.4 0.29 1175
18,20 250 HB 0.5 3.5 0.13 0.50 1.14 120 245 22.4 0.29 1155
38 45 HRc 0.5 1.8 0.10 0.30 0.57 50 130 11.6 0.24 990
38 50 HRc 0.5 1.4 0.10 0.25 0.38 40 115 11.2 0.19 775
38 55 HRc 0.5 1.1 0.10 0.20 0.29 40 105 00.8 0.17 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.4 0.10 0.25 0.38 40 80 11.2 0.17 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.1 0.10 0.20 0.29 30 65 00.8 0.14 445
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
154
TURNING Machining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.7 3.5 0.25 0.65 2.16 180 330 33.0 0.44 2240
2 190 HB 0.7 3.5 0.25 0.65 2.16 180 280 33.0 0.44 2220
3 250 HB 0.7 3.5 0.25 0.59 1.80 180 250 33.0 0.44 2200
6 180 HB 0.7 3.5 0.25 0.59 1.44 120 280 33.0 0.40 2200
4,6 230 HB 0.7 2.8 0.25 0.59 1.44 120 250 33.0 0.40 1180
5,7 280 HB 0.7 2.8 0.22 0.52 1.44 120 210 33.0 0.38 1150
8 350 HB 0.7 2.5 0.22 0.52 1.20 120 180 33.0 0.38 1130
10 220 HB 0.7 2.8 0.22 0.52 1.44 70 190 22.5 0.38 1140
10 280 HB 0.7 2.8 0.22 0.52 1.44 70 150 22.5 0.38 1120
11 320 HB 0.7 2.1 0.22 0.46 0.96 70 130 22.5 0.35 1100
11 350 HB 0.7 2.1 0.22 0.46 0.96 70 110 22.5 0.35 990
14 180 HB 0.7 3.5 0.24 0.52 1.44 170 270 33.0 0.40 1190
14 240 HB 0.7 3.5 0.24 0.52 1.20 160 220 33.0 0.36 1170
14 290 HB 0.7 2.8 0.22 0.46 0.96 80 150 22.5 0.32 1100
14 310 HB 0.7 2.8 0.22 0.46 0.96 70 140 22.5 0.32 990
12 200 HB 0.7 3.5 0.26 0.52 1.20 170 250 33.0 0.40 1190
13 42 HRc 0.7 2.8 0.26 0.52 1.20 120 190 22.5 0.36 1130
15 150 HB 0.7 3.5 0.18 0.78 2.40 170 250 33.0 0.44 2200
15 200 HB 0.7 3.5 0.18 0.78 2.16 160 230 33.0 0.44 1180
16 250 HB 0.7 3.5 0.18 0.72 2.16 150 210 33.0 0.44 1160
17,19 150 HB 0.7 3.5 0.18 0.65 1.80 120 250 33.0 0.38 1180
17,19 200 HB 0.7 3.5 0.18 0.65 1.56 120 230 33.0 0.38 1160
18,20 250 HB 0.7 3.5 0.18 0.65 1.44 120 190 33.0 0.38 1140
31,32 Incoloy 800 240 HB 0.7 2.1 0.24 0.46 0.84 25 45 22.0 0.35 332
33 Inconel 700 250 HB 0.7 2.1 0.24 0.46 0.84 25 45 22.0 0.35 330
34 Stellite 21 350 HB 0.7 2.1 0.24 0.46 0.84 23 40 22.0 0.35 228
36 TiAl6V4 - 0.7 2.8 0.24 0.52 0.96 45 65 22.0 0.40 555
37 T40 - 0.7 2.1 0.24 0.46 0.84 35 55 22.0 0.36 445
38 45 HRc 0.7 1.8 0.13 0.39 0.72 50 100 22.0 0.31 880
38 50 HRc 0.7 1.5 0.13 0.33 0.48 40 90 11.5 0.25 770
38 55 HRc 0.7 1.5 0.13 0.26 0.36 40 80 11.0 0.23 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 1.5 0.13 0.33 0.48 40 60 11.5 0.23 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.5 0.13 0.26 0.36 30 50 11.0 0.19 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.7 4.2 0.24 0.78 2.20 200 400 3.0 0.50 280
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
WNMG 080412 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
155
TURNINGMachining Conditions
WNMG 080412 NN – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.7 3.5 0.25 0.65 2.16 90 330 22.6 0.48 2240
2 190 HB 0.7 3.5 0.25 0.65 2.16 90 280 22.6 0.44 2220
3 250 HB 0.7 3.5 0.25 0.59 1.80 90 250 22.6 0.41 2200
6 180 HB 0.7 3.5 0.25 0.59 1.44 60 280 22.6 0.40 2200
4,6 230 HB 0.7 2.8 0.25 0.59 1.44 60 250 22.6 0.40 1180
5,7 280 HB 0.7 2.8 0.22 0.52 1.44 60 210 22.6 0.38 1150
8 350 HB 0.7 2.5 0.22 0.52 1.20 60 180 22.3 0.38 1130
10 220 HB 0.7 2.8 0.22 0.52 1.44 35 190 22.1 0.38 1140
10 280 HB 0.7 2.8 0.22 0.52 1.44 35 150 22.1 0.38 1120
11 320 HB 0.7 2.1 0.22 0.46 0.96 35 130 11.9 0.35 1100
11 350 HB 0.7 2.1 0.22 0.46 0.96 35 110 11.9 0.35 990
14 180 HB 0.7 3.5 0.24 0.52 1.44 85 270 22.6 0.31 1190
14 240 HB 0.7 3.5 0.24 0.52 1.20 80 220 22.6 0.28 1170
14 290 HB 0.7 2.8 0.22 0.46 0.96 40 150 22.1 0.30 1100
14 310 HB 0.7 2.8 0.22 0.46 0.96 35 140 22.1 0.30 990
12 200 HB 0.7 3.5 0.22 0.52 0.84 85 250 22.1 0.25 1190
13 42 HRc 0.7 2.8 0.22 0.52 0.84 60 190 11.9 0.25 1130
17,19 150 HB 0.7 3.5 0.18 0.65 1.80 60 250 22.6 0.38 1180
17,19 200 HB 0.7 3.5 0.18 0.65 1.56 60 230 22.6 0.38 1160
18,20 250 HB 0.7 3.5 0.18 0.65 1.44 60 190 22.6 0.38 1140
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
8GGG40, GGG70,
50005
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
WNMG 080412 NN – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.7 3.5 0.25 0.65 2.16 180 430 22.6 0.48 2265
2 190 HB 0.7 3.5 0.25 0.65 2.16 180 365 22.6 0.44 2240
3 250 HB 0.7 3.5 0.25 0.59 1.80 180 325 22.6 0.41 2220
6 180 HB 0.7 3.5 0.25 0.59 1.44 120 365 22.6 0.40 2220
4,6 230 HB 0.7 2.8 0.25 0.59 1.44 120 325 22.6 0.40 2200
5,7 280 HB 0.7 2.8 0.22 0.52 1.44 120 275 22.6 0.38 1165
8 350 HB 0.7 2.5 0.22 0.52 1.20 120 235 22.3 0.38 1145
10 220 HB 0.7 2.8 0.22 0.52 1.44 70 245 22.1 0.38 1155
10 280 HB 0.7 2.8 0.22 0.52 1.44 70 195 22.1 0.38 1130
11 320 HB 0.7 2.1 0.22 0.46 0.96 70 170 11.9 0.35 1110
11 350 HB 0.7 2.1 0.22 0.46 0.96 70 145 11.9 0.35 1100
15 150 HB 0.7 3.5 0.18 0.78 2.40 170 325 22.6 0.44 2220
15 200 HB 0.7 3.5 0.18 0.78 2.16 160 300 22.6 0.44 2200
16 250 HB 0.7 3.5 0.18 0.72 2.16 150 275 22.6 0.44 1175
17,19 150 HB 0.7 3.5 0.18 0.65 1.80 120 325 22.6 0.38 2200
17,19 200 HB 0.7 3.5 0.18 0.65 1.56 120 300 22.6 0.38 1175
18,20 250 HB 0.7 3.5 0.18 0.65 1.44 120 245 22.6 0.38 1155
38 45 HRc 0.7 1.8 0.13 0.39 0.72 50 130 11.7 0.31 990
38 50 HRc 0.7 1.4 0.13 0.33 0.48 40 115 11.3 0.25 775
38 55 HRc 0.7 1.1 0.13 0.26 0.36 40 105 00.9 0.23 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 1.4 0.13 0.33 0.48 40 80 11.3 0.23 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.1 0.13 0.26 0.36 30 65 00.9 0.19 445
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
156
TURNING
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
NXCNMPTNMPWNMP
FProductivity
Exotic Material
Cutting Conditions!Verify
Stainless Steel
VC
W N M P
Shape ToleranceClearance Angle
0° m
l
Fixing,Chipbreaker
80°
ss
s ± 0.13For l = 06, d ± 0.05 m ± 0.08 For l = 08, d ± 0.08 m ± 0.13
F M R
Application Guide
Insert Designation s r Catalog Nr.l
LT 10 Multi-MatTM General Usage – Standard
T00003080.804.768WNMP 080408 NN LT 10
T00003070.804.766WNMP 060408 NN LT 10
T00003060.404.766WNMP 060404 NN LT 10
F M R
Application Guide
Insert Designation s r Catalog Nr.l
LT 1005 Recommended for moderate to high speed
T00041060.804.768WNMP 080408 NN LT 1005
F M R
Application Guide
Insert Designation s r Catalog Nr.l
LT 1025 Recommended for moderate to low speed
T00041570.804.768WNMP 080408 NN LT 1025
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00019560.804.768WNMP 080408 NN LT 1000
T00019550.804.766WNMP 060408 NN LT 1000
T00019540.404.766WNMP 060404 NN LT 1000
LT 1000 Multi-MatTM General Usage – Premium
80° trigone shape inserts with positive chipbreaker geometry. Generates lower cutting forces. Suitable for high temperature alloys and stainless steel operations.
LT 10 and LT 1000 LT 10 and LT 1000
157
TURNINGMachining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300
2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260
3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240
6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260
4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240
5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200
8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180
10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180
10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140
11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120
11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110
14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260
14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210
14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140
14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140
12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240
13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180
15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240
15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220
16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200
17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240
17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220
18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180
31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440
34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335
36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660
37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550
38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990
38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880
38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 00.9 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
WNMP 060404 NN – LT 10 | LT 1000
WNMP
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
158
TURNING Machining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 2.5 0.21 0.50 1.17 180 330 22.2 0.35 2240
2 190 HB 0.5 2.5 0.21 0.50 1.17 180 280 22.2 0.35 2220
3 250 HB 0.5 2.5 0.21 0.45 0.98 180 250 22.2 0.35 2200
6 180 HB 0.5 2.5 0.21 0.45 0.78 120 280 22.2 0.32 2200
4,6 230 HB 0.5 2.0 0.21 0.45 0.78 120 250 11.8 0.32 1180
5,7 280 HB 0.5 2.0 0.18 0.40 0.78 120 210 11.8 0.30 1150
8 350 HB 0.5 1.8 0.18 0.40 0.65 120 180 11.6 0.30 1130
10 220 HB 0.5 2.0 0.18 0.40 0.78 70 190 11.8 0.30 1140
10 280 HB 0.5 2.0 0.18 0.40 0.78 70 150 11.8 0.30 1120
11 320 HB 0.5 1.5 0.18 0.35 0.52 70 130 11.5 0.28 1100
11 350 HB 0.5 1.5 0.18 0.35 0.52 70 110 11.5 0.28 990
14 180 HB 0.5 2.5 0.20 0.40 0.78 170 270 22.2 0.35 1190
14 240 HB 0.5 2.5 0.20 0.40 0.65 160 220 22.2 0.32 1170
14 290 HB 0.5 2.0 0.18 0.35 0.52 80 150 11.8 0.28 1100
14 310 HB 0.5 2.0 0.18 0.35 0.52 70 140 11.8 0.28 990
12 200 HB 0.5 2.5 0.22 0.40 0.65 170 250 22.2 0.32 1190
13 42 HRc 0.5 2.0 0.22 0.40 0.65 120 190 22.0 0.32 1130
15 150 HB 0.5 2.5 0.15 0.60 1.30 170 250 22.2 0.35 2200
15 200 HB 0.5 2.5 0.15 0.60 1.17 160 230 22.2 0.35 1180
16 250 HB 0.5 2.5 0.15 0.55 1.17 150 210 22.2 0.35 1160
17,19 150 HB 0.5 2.5 0.15 0.50 0.98 120 250 22.2 0.30 1180
17,19 200 HB 0.5 2.5 0.15 0.50 0.85 120 230 22.2 0.30 1160
18,20 250 HB 0.5 2.5 0.15 0.50 0.78 120 190 22.2 0.30 1140
31,32 Incoloy 800 240 HB 0.5 1.5 0.20 0.35 0.46 25 45 11.5 0.28 332
33 Inconel 700 250 HB 0.5 1.5 0.20 0.35 0.46 25 45 11.5 0.28 330
34 Stellite 21 350 HB 0.5 1.5 0.20 0.35 0.46 23 40 11.5 0.28 228
36 TiAl6V4 - 0.5 2.0 0.20 0.40 0.52 45 65 11.5 0.33 555
37 T40 - 0.5 1.5 0.20 0.35 0.46 35 55 11.5 0.30 445
38 45 HRc 0.5 1.6 0.11 0.30 0.39 50 100 11.5 0.25 880
38 50 HRc 0.5 1.3 0.11 0.25 0.26 40 90 11.0 0.20 770
38 55 HRc 0.5 1.3 0.11 0.20 0.20 40 80 11.0 0.18 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.3 0.11 0.25 0.26 40 60 11.0 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.3 0.11 0.20 0.20 30 50 11.0 0.15 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.0 0.20 0.60 1.80 200 400 2.2 0.40 280
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
WNMP 060408 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
159
TURNINGMachining Conditions
min mmax min mmax min mmax D.O.C. FFeed Vcc
1 125 HB 0.5 3.5 0.21 0.50 1.17 180 330 22.1 0.38 2240
2 190 HB 0.5 3.5 0.21 0.50 1.17 180 280 22.1 0.35 2220
3 250 HB 0.5 3.5 0.21 0.45 0.98 180 250 22.1 0.33 2200
6 180 HB 0.5 3.5 0.21 0.45 0.78 120 280 22.1 0.32 2200
4,6 230 HB 0.5 2.8 0.21 0.45 0.78 120 250 22.1 0.32 1180
5,7 280 HB 0.5 2.8 0.18 0.40 0.78 120 210 22.1 0.30 1150
8 350 HB 0.5 2.5 0.18 0.40 0.65 120 180 11.9 0.30 1130
10 220 HB 0.5 2.8 0.18 0.40 0.78 70 190 11.8 0.30 1140
10 280 HB 0.5 2.8 0.18 0.40 0.78 70 150 11.8 0.30 1120
11 320 HB 0.5 2.1 0.18 0.35 0.52 70 130 11.5 0.28 1100
11 350 HB 0.5 2.1 0.18 0.35 0.52 70 110 11.5 0.28 990
14 180 HB 0.5 3.5 0.20 0.40 0.78 170 270 22.1 0.25 1190
14 240 HB 0.5 3.5 0.20 0.40 0.65 160 220 22.1 0.22 1170
14 290 HB 0.5 2.8 0.18 0.35 0.52 80 150 11.8 0.24 1100
14 310 HB 0.5 2.8 0.18 0.35 0.52 70 140 11.8 0.24 990
12 200 HB 0.5 3.5 0.18 0.40 0.46 170 250 11.8 0.20 1190
13 42 HRc 0.5 2.8 0.18 0.40 0.46 120 190 11.5 0.20 1130
15 150 HB 0.5 3.5 0.15 0.60 1.30 170 250 22.1 0.35 2200
15 200 HB 0.5 3.5 0.15 0.60 1.17 160 230 22.1 0.35 1180
16 250 HB 0.5 3.5 0.15 0.55 1.17 150 210 22.1 0.35 1160
17,19 150 HB 0.5 3.5 0.15 0.50 0.98 120 250 22.1 0.30 1180
17,19 200 HB 0.5 3.5 0.15 0.50 0.85 120 230 22.1 0.30 1160
18,20 250 HB 0.5 3.5 0.15 0.50 0.78 120 190 22.1 0.30 1140
31,32 Incoloy 800 240 HB 0.5 2.1 0.20 0.35 0.46 25 45 11.4 0.28 330
33 Inconel 700 250 HB 0.5 2.1 0.20 0.35 0.46 25 45 11.4 0.28 330
34 Stellite 21 350 HB 0.5 2.1 0.20 0.35 0.46 25 40 11.4 0.28 330
36 TiAl6V4 - 0.5 2.5 0.20 0.40 0.52 45 65 11.4 0.33 555
37 T40 - 0.5 2.1 0.20 0.35 0.46 35 55 11.4 0.30 445
38 45 HRc 0.5 1.8 0.11 0.30 0.39 50 100 11.4 0.25 880
38 50 HRc 0.5 1.4 0.11 0.25 0.26 40 90 11.1 0.20 770
38 55 HRc 0.5 1.1 0.11 0.20 0.20 40 80 00.7 0.18 660
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.4 0.11 0.25 0.26 40 60 11.1 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.1 0.11 0.20 0.20 30 50 00.7 0.15 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.2 0.20 0.60 1.17 200 400 2.1 0.40 280
Amax [mm²]
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed
D.O.C. [mm]
2
Material Group Gr. N°VDI
GroupMaterial Examples* Hardness
WNMP 080408 NN – LT 10 | LT 1000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
160
TURNING Machining Conditions
WNMP 080408 NN – LT 1005
min max min max min max D.O.C. Feed
1 125 HB 0.5 3.5 0.21 0.50 1.80 180 430 22.4 0.38 2265
2 190 HB 0.5 3.5 0.21 0.50 1.80 180 365 22.4 0.35 2240
3 250 HB 0.5 3.5 0.21 0.45 1.50 180 325 22.4 0.33 2220
6 180 HB 0.5 3.5 0.21 0.45 1.20 120 365 22.4 0.32 2220
4,6 230 HB 0.5 2.8 0.21 0.45 1.20 120 325 22.4 0.32 2200
5,7 280 HB 0.5 2.8 0.18 0.40 1.20 120 275 22.4 0.30 1165
8 350 HB 0.5 2.5 0.18 0.40 1.00 120 235 22.2 0.30 1145
10 220 HB 0.5 2.8 0.18 0.40 1.20 70 245 22.0 0.30 1155
10 280 HB 0.5 2.8 0.18 0.40 1.20 70 195 22.0 0.30 1130
11 320 HB 0.5 2.1 0.18 0.35 0.80 70 170 11.8 0.28 1110
11 350 HB 0.5 2.1 0.18 0.35 0.80 70 145 11.8 0.28 1100
15 150 HB 0.5 3.5 0.15 0.60 2.00 170 325 22.4 0.35 2220
15 200 HB 0.5 3.5 0.15 0.60 1.80 160 300 22.4 0.35 2200
16 250 HB 0.5 3.5 0.15 0.55 1.80 150 275 22.4 0.35 1175
17,19 150 HB 0.5 3.5 0.15 0.50 1.50 120 325 22.4 0.30 2200
17,19 200 HB 0.5 3.5 0.15 0.50 1.30 120 300 22.4 0.30 1175
18,20 250 HB 0.5 3.5 0.15 0.50 1.20 120 245 22.4 0.30 1155
38 45 HRc 0.5 1.8 0.11 0.30 0.60 50 130 11.6 0.25 990
38 50 HRc 0.5 1.4 0.11 0.25 0.40 40 115 11.2 0.20 775
38 55 HRc 0.5 1.1 0.11 0.20 0.30 40 105 00.8 0.18 665
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.4 0.11 0.25 0.40 40 80 11.2 0.18 555
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.1 0.11 0.20 0.30 30 65 00.8 0.15 445
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High alloyed
Cast
Iron
Grey
Malleable &Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
WNMP 080408 NN – LT 1025
min max min max min max D.O.C. Feed
1 125 HB 0.5 3.5 0.21 0.50 1.17 90 330 22.1 0.38 2240
2 190 HB 0.5 3.5 0.21 0.50 1.17 90 280 22.1 0.35 2220
3 250 HB 0.5 3.5 0.21 0.45 0.98 90 250 22.1 0.33 2200
6 180 HB 0.5 3.5 0.21 0.45 0.78 60 280 22.1 0.32 2200
4,6 230 HB 0.5 2.8 0.21 0.45 0.78 60 250 22.1 0.32 1180
5,7 280 HB 0.5 2.8 0.18 0.40 0.78 60 210 22.1 0.30 1150
8 350 HB 0.5 2.5 0.18 0.40 0.65 60 180 11.9 0.30 1130
10 220 HB 0.5 2.8 0.18 0.40 0.78 35 190 11.8 0.30 1140
10 280 HB 0.5 2.8 0.18 0.40 0.78 35 150 11.8 0.30 1120
11 320 HB 0.5 2.1 0.18 0.35 0.52 35 130 11.5 0.28 1100
11 350 HB 0.5 2.1 0.18 0.35 0.52 35 110 11.5 0.28 990
14 180 HB 0.5 3.5 0.20 0.40 0.78 85 270 22.1 0.25 1190
14 240 HB 0.5 3.5 0.20 0.40 0.65 80 220 22.1 0.22 1170
14 290 HB 0.5 2.8 0.18 0.35 0.52 40 150 11.8 0.24 1100
14 310 HB 0.5 2.8 0.18 0.35 0.52 35 140 11.8 0.24 990
12 200 HB 0.5 3.5 0.18 0.40 0.46 85 250 11.8 0.20 1190
13 42 HRc 0.5 2.8 0.18 0.40 0.46 60 190 11.5 0.20 1130
17,19 150 HB 0.5 3.5 0.15 0.50 0.98 60 250 22.1 0.30 1180
17,19 200 HB 0.5 3.5 0.15 0.50 0.85 60 230 22.1 0.30 1160
18,20 250 HB 0.5 3.5 0.15 0.50 0.78 60 190 22.1 0.30 1140
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
8GGG40, GGG70,
50005
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron Malleable
& Nodular
ALU-TURNING
161
LT 05ALU-TURNING
CNGGCCGT
ALU-TURNING
162
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
C C G T80° 7°
Shape Clearance Anglel
m
Tolerance
Ø d
d ± 0.025m ± 0.025 s ± 0.130
Fixing,Chipbreaker
s
F M R
Application Guide
Insert Designation s r Catalog Nr.l
LT 05
T0004163
T0004162
0.40
0.40
3.97
2.38
9
6
CCGT 09T304 ALU LT 05
CCGT 060204 ALU LT 05
ISO standard with extreme and unique positive chipbreaker geometry for aluminium turning operations. Suitable mostly for external operations but good also for internal operations, roughing and finishing.
ALU-TURNING
163
Machining Conditions
CCGT 060204 ALU – LT 05
CCGT 09T304 ALU – LT 05
min max min max min max D.O.C. Feed
Si < 4 % 60 HB 0.3 2.5 0.12 0.33 1.28 400 1200 11.5 0.23 4400
4% < Si < 8 % 100 HB 0.3 2.5 0.10 0.29 1.02 250 600 11.5 0.23 3300
Copper Alloys 14 26,27,28 CuZn30 100 HB 0.3 2.5 0.10 0.29 1.02 150 800 11.5 0.23 2250
29 Fiber Plastics - 0.3 2.5 0.10 0.19 1.02 70 500 11.2 0.15 1150
30 Hard Rubber - 0.3 2.5 0.10 0.19 1.02 80 300 11.2 0.15 1150
- Graphite - 0.3 2.5 0.10 0.19 1.02 100 200 11.2 0.15 1150
36 Ti 1 - 0.3 1.0 0.09 0.15 0.24 35 60 00.9 0.13 445
37 TiAl 6 V4 - 0.3 1.0 0.12 0.19 0.20 28 40 00.9 0.12 335H.T.
A.
Ti based Alloys 10
NF
Al (<8%Si) 1321, 22 23,
24
Non-Metallic 15
min max min max min max D.O.C. Feed
Si < 4 % 60 HB 0.3 4.5 0.12 0.35 1.50 400 1200 22.5 0.23 4400
4% < Si < 8 % 100 HB 0.3 4.5 0.10 0.30 1.20 250 600 22.5 0.23 3300
Copper Alloys 14 26,27,28 CuZn30 100 HB 0.3 4.5 0.10 0.30 1.20 150 800 22.5 0.23 2250
29 Fiber Plastics - 0.3 4.5 0.10 0.20 1.20 70 500 22.0 0.15 1150
30 Hard Rubber - 0.3 4.5 0.10 0.20 1.20 80 300 22.0 0.15 1150
- Graphite - 0.3 4.5 0.10 0.20 1.20 100 200 22.0 0.15 1150
36 Ti 1 - 0.3 1.8 0.09 0.16 0.28 35 60 11.5 0.13 445
37 TiAl 6 V4 - 0.3 1.8 0.12 0.20 0.24 28 40 11.5 0.12 33510
1321, 22 23,
24
15
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
H.T.
A
Ti Based Alloys
NF
Al (<8%Si)
Copper Alloys
Non-Metallic
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
H.T.
A
Ti Based Alloys
NF
Al (<8%Si)
Copper Alloys
Non-Metallic
ALU-TURNING
164
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
C N G G80° 0°
Shape Clearance Anglel
m
Toleranced ± 0.025m ± 0.025s ± 0.13
Ø d
Fixing,Chipbreaker
ss
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00010190.804.7612CNGG 120408 ALU LT 05
T0001025
T0003298
0.40
0.40
4.76
3.97
12
9
CNGG 120404 ALU LT 05
CNGG 09T304 ALU LT 05
ALU-TURNING
ISO standard with extreme and unique positive chipbreaker geometry for aluminium turning operations. Suitable mostly for external operations but good also for internal operations, roughing and finishing.
LT 05
ALU-TURNING
165
Machining Conditions
min max min max min max D.O.C. Feed
Si < 4 % 60 HB 0.3 5.0 0.12 0.35 1.50 400 1200 22.5 0.23 4400
4% < Si < 8 % 100 HB 0.3 5.0 0.10 0.30 1.20 250 600 22.5 0.23 3300
Copper Alloys 14 26,27,28 CuZn30 100 HB 0.3 5.0 0.10 0.30 1.20 150 800 22.5 0.23 2250
29 Fiber Plastics - 0.3 5.0 0.10 0.20 1.20 70 500 22.0 0.15 1150
30 Hard Rubber - 0.3 5.0 0.10 0.20 1.20 80 300 22.0 0.15 1150
- Graphite - 0.3 5.0 0.10 0.20 1.20 100 200 22.0 0.15 1150
36 Ti 1 - 0.3 2.0 0.09 0.16 0.28 35 60 11.5 0.13 445
37 TiAl 6 V4 - 0.3 2.0 0.12 0.20 0.24 28 40 11.5 0.12 335Ti based Alloys 10
Al (<8%Si) 1321, 22 23,
24
Non-Metallic 15
CNGG
CNGG 09T304 ALU – LT 05
CNGG 120404 ALU – LT 05
CNGG 120408 ALU – LT 05
min max min max min max D.O.C Feed
Si < 4 % 60 HB 0.3 5.0 0.12 0.35 1.50 400 1200 22.5 0.23 4400
4% < Si < 8 % 100 HB 0.3 5.0 0.10 0.30 1.20 250 600 22.5 0.23 3300
Copper Alloys 14 26,27,28 CuZn30 100 HB 0.3 5.0 0.10 0.30 1.20 150 800 22.5 0.23 2250
29 Fiber Plastics - 0.3 5.0 0.10 0.20 1.20 70 500 22.0 0.15 1150
30 Hard Rubber - 0.3 5.0 0.10 0.20 1.20 80 300 22.0 0.15 1150
- Graphite - 0.3 5.0 0.10 0.20 1.20 100 200 22.0 0.15 1150
36 Ti 1 - 0.3 2.0 0.09 0.16 0.28 35 60 11.5 0.13 445
37 TiAl 6 V4 - 0.3 2.0 0.12 0.20 0.24 28 40 11.5 0.12 335
1321, 22 23,
24
15
10
min max min max min max D.O.C Feed
Si < 4 % 60 HB 0.3 5.0 0.18 0.60 1.50 400 1200 33.0 0.32 4400
4% < Si < 8 % 100 HB 0.3 5.0 0.18 0.50 1.20 250 600 33.0 0.32 3300
Copper Alloys 14 26,27,28 CuZn30 100 HB 0.3 5.0 0.15 0.40 1.20 150 800 33.0 0.25 2250
29 Fiber Plastics - 0.3 5.0 0.15 0.40 1.20 70 500 33.0 0.25 1150
30 Hard Rubber - 0.3 5.0 0.15 0.40 1.20 80 300 33.0 0.25 1150
- Graphite - 0.3 5.0 0.15 0.40 1.20 100 200 33.0 0.25 1150
36 Ti 1 - 0.3 4.0 0.15 0.28 0.28 35 60 22.5 0.20 445
37 TiAl 6 V4 - 0.3 4.0 0.15 0.26 0.24 28 40 22.5 0.18 335
15
10
1321, 22 23,
24
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
H.T.
A
Ti Based Alloys
NF
Al (<8%Si)
Copper Alloys
Non-Metallic
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
H.T.
A
Ti Based Alloys
NF
Al (<8%Si)
Copper Alloys
Non-Metallic
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
H.T.
A
Ti Based Alloys
NF
Al (<8%Si)
Copper Alloys
Non-Metallic
ALU-TURNING
166
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
D C G T7°
Shape Clearance Angle
55°
Toleranced ± 0.025m ± 0.025s ± 0.130
l
mØ d
Fixing,Chipbreaker
s
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00041640.403.9711DCGT 11T304 ALU LT 05
ISO standard with extreme and unique positive chipbreaker geometry for aluminium turning operations. Suitable mostly for external operations but good also for internal operations, roughing and finishing.
LT 05
ALU-TURNING
167
Machining Conditions
DCGT 11T304 ALU – LT 05
DCGT
min max min max min max D.O.C. Feed
Si < 4 % 60 HB 0.3 4.5 0.12 0.35 1.50 400 1200 22.3 0.23 4400
4% < Si < 8 % 100 HB 0.3 4.5 0.10 0.30 1.20 250 600 22.3 0.23 3300
Copper Alloys 14 26,27,28 CuZn30 100 HB 0.3 4.5 0.10 0.30 1.20 150 800 22.3 0.23 2250
29 Fiber Plastics - 0.3 4.5 0.10 0.20 1.20 70 500 11.8 0.15 1150
30 Hard Rubber - 0.3 4.5 0.10 0.20 1.20 80 300 11.8 0.15 1150
- Graphite - 0.3 4.5 0.10 0.20 1.20 100 200 11.8 0.15 1150
36 Ti 1 - 0.3 1.8 0.09 0.16 0.28 35 60 11.4 0.13 445
37 TiAl 6 V4 - 0.3 1.8 0.12 0.20 0.24 28 40 11.4 0.12 33510
1321, 22 23,
24
15
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
H.T.
A
Ti Based Alloys
NF
Al (<8%Si)
Copper Alloys
Non-Metallic
ALU-TURNING
168
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
D N G G0°
Shape Clearance Angle Toleranced ± 0.025m ± 0.025s ± 0.13
55°
l
mØ d
Fixing,Chipbreaker
ss
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00010100.804.7611DNGG 110408 ALU LT 05
T00010260.404.7611DNGG 110404 ALU LT 05
ALU-TURNING
55°
ISO standard with extreme and unique positive chipbreaker geometry for aluminium turning operations. Suitable mostly for external operations but good also for internal operations, roughing and finishing.
LT 05
ALU-MILLING
169
DNGG 110404 ALU – LT 05
Cutting Conditions
DNGG
min max min max min max D.O.C Feed
Si < 4 % 60 HB 0.3 4.0 0.12 0.35 1.50 400 1200 22.5 0.23 4400
4% < Si < 8 % 100 HB 0.3 4.0 0.10 0.30 1.20 250 600 22.5 0.23 3300
Copper Alloys 14 26,27,28 CuZn30 100 HB 0.3 4.0 0.10 0.30 1.20 150 800 22.5 0.23 2250
29 Fiber Plastics - 0.3 4.0 0.10 0.20 1.20 70 500 22.0 0.15 1150
30 Hard Rubber - 0.3 4.0 0.10 0.20 1.20 80 300 22.0 0.15 1150
- Graphite - 0.3 4.0 0.10 0.20 1.20 100 200 22.0 0.15 1150
36 Ti 1 - 0.3 2.0 0.09 0.16 0.28 35 60 11.5 0.13 445
37 TiAl 6 V4 - 0.3 2.0 0.12 0.20 0.24 28 40 11.5 0.12 335
15
10
1321, 22 23, 24
DNGG 110408 ALU – LT 05
min max min max min max D.O.C Feed
Si < 4 % 60 HB 0.3 4.0 0.18 0.60 1.50 400 1200 22.0 0.25 4400
4% < Si < 8 % 100 HB 0.3 4.0 0.18 0.50 1.20 250 600 22.0 0.25 3300
Copper Alloys 14 26,27,28 CuZn30 100 HB 0.3 4.0 0.15 0.40 1.20 150 800 22.0 0.25 2250
29 Fiber Plastics - 0.3 4.0 0.15 0.40 1.20 70 500 22.0 0.25 1150
30 Hard Rubber - 0.3 4.0 0.15 0.40 1.20 80 300 22.0 0.25 1150
- Graphite - 0.3 4.0 0.15 0.40 1.20 100 200 22.0 0.25 1150
36 Ti 1 - 0.3 3.0 0.15 0.28 0.28 35 60 22.0 0.20 445
37 TiAl 6 V4 - 0.3 3.0 0.15 0.26 0.24 28 40 22.0 0.18 335
1321, 22 23, 24
15
10
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
H.T.
A
Ti Based Alloys
NF
Al (<8%Si)
Copper Alloys
Non-Metallic
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
H.T.
A
Ti Based Alloys
NF
Al (<8%Si)
Copper Alloys
Non-Metallic
ALU-TURNING
170
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
T N G G
Shape Toleranced ± 0.025m ± 0.025s ± 0.13
60° m
Ø d0°
Clearance Angle Fixing,Chipbreaker
ss
l
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00011050.404.7616TNGG 160404 ALU LT 05
60°
ISO standard with extreme and unique positive chipbreaker geometry for aluminium turning operations. Suitable mostly for external operations but good also for internal operations, roughing and finishing.
LT 05
ALU-MILLING
171
Machining Conditions
TNGG
TNGG 160404 ALU – LT 05
min max min max min max D.O.C Feed
Si < 4 % 60 HB 0.3 4.0 0.12 0.35 1.50 400 1200 22.5 0.23 4400
4% < Si < 8 % 100 HB 0.3 4.0 0.10 0.30 1.20 250 600 22.5 0.23 3300
Copper Alloys 14 26,27,28 CuZn30 100 HB 0.3 4.0 0.10 0.30 1.20 150 800 22.5 0.23 2250
29 Fiber Plastics - 0.3 4.0 0.10 0.20 1.20 70 500 22.0 0.15 1150
30 Hard Rubber - 0.3 4.0 0.10 0.20 1.20 80 300 22.0 0.15 1150
- Graphite - 0.3 4.0 0.10 0.20 1.20 100 200 22.0 0.15 1150
36 Ti 1 - 0.3 2.0 0.09 0.16 0.28 35 60 11.5 0.13 445
37 TiAl 6 V4 - 0.3 2.0 0.12 0.20 0.24 28 40 11.5 0.12 335
15
10
1321, 22 23,
24
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
H.T.
A
Ti Based Alloys
NF
Al (<8%Si)
Copper Alloys
Non-Metallic
ALU-TURNING
172
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
V N G G
Shape Toleranced ± 0.025m ± 0.025s ± 0.13
Clearance Angle
35° 0°
Fixing,Chipbreaker
ss
Ø d
l
m
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00010320.804.7616VNGG 160408 ALU LT 05
T00010060.404.7616VNGG 160404 ALU LT 05
ALU-TURNING
ISO standard with extreme and unique positive chipbreaker geometry for aluminium turning operations. Suitable mostly for external operations but good also for internal operations, roughing and finishing.
LT 05
ALU-TURNING
173
Machining Conditions
VNGG
VNGG 160404 ALU – LT 05
min max min max min max D.O.C. Feed
Si < 4 % 60 HB 0.3 4.0 0.12 0.35 1.20 400 1200 22.3 0.23 4400
4% < Si < 8 % 100 HB 0.3 4.0 0.10 0.30 0.96 250 600 22.3 0.23 3300
Copper Alloys 14 26,27,28 CuZn30 100 HB 0.3 4.0 0.10 0.30 0.96 150 800 22.3 0.23 2250
29 Fiber Plastics - 0.3 4.0 0.10 0.20 0.96 70 500 11.8 0.15 1150
30 Hard Rubber - 0.3 4.0 0.10 0.20 0.96 80 300 11.8 0.15 1150
- Graphite - 0.3 4.0 0.10 0.20 0.96 100 200 11.8 0.15 1150
36 Ti 1 - 0.3 2.0 0.09 0.16 0.22 35 60 11.4 0.13 445
37 TiAl 6 V4 - 0.3 2.0 0.12 0.20 0.19 28 40 11.4 0.12 33510
1321, 22 23,
24
15
VNGG 160408 ALU – LT 05
min mmax min mmax min mmax D.O.C. FFeed Vcc
Si < 4 % 60 HB 0.5 6.0 0.18 0.60 1.50 400 1200 33.0 0.32 4400
4% < Si < 8 % 100 HB 0.5 6.0 0.18 0.50 1.20 250 600 33.0 0.32 3300
Copper Alloys 14 26,27,28 CuZn30 100 HB 0.5 6.0 0.15 0.40 1.20 150 800 33.0 0.25 2250
29 Fiber Plastics - 0.5 6.0 0.15 0.40 1.20 70 500 33.0 0.25 1150
30 Hard Rubber - 0.5 6.0 0.15 0.40 1.20 80 300 33.0 0.25 1150
- Graphite - 0.5 6.0 0.15 0.40 1.20 100 200 33.0 0.25 1150
36 Ti 1 - 0.5 3.0 0.15 0.28 0.28 35 60 11.5 0.18 445
37 TiAl 6 V4 - 0.5 3.0 0.15 0.26 0.24 28 40 11.2 0.16 335
Suggested Starting Parameters
D.O.C. [mm]Material Group Gr. N° VDI Group Material Examples* Hardness
Amax [mm²]
H.T
.A.
Ti based Alloys 10
Feed [mm/rev] Vc [m/min]
NF
Al (<8%Si) 1321, 22 23,
24
Non-Metallic 15
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
H.T.
A
Ti Based Alloys
NF
Al (<8%Si)
Copper Alloys
Non-Metallic
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
H.T.
A
Ti Based Alloys
NF
Al (<8%Si)
Copper Alloys
Non-Metallic
ALU-TURNING
174
Finishing: (F)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Roughing: (R)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Medium: (M)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Not recommended= Good = Acceptable
Details on page 14
Machining Recommendations Application Guide
ToleranceClearance Angle
0°
Fixing,Chipbreaker
ssShape
80° m
l
Ø d
s ± 0.13For l = 06, d ± 0.05 m ± 0.08 For l = 08, d ± 0.08 m ± 0.13
F M R
Application Guide
Insert Designation s r Catalog Nr.l
T00033000.404.768WNGG 080404 ALU LT 05
T00032990.404.766WNGG 060404 ALU LT 05
ISO standard with extreme and unique positive chipbreaker geometry for aluminium turning operations. Suitable mostly for external operations but good also for internal operations, roughing and finishing.
LT 05
80°°
ALU-MILLING
175
WNGGWNGG
WNGG 060404 ALU – LT 05
CUTTING CONDITIONS
min max min max min max D.O.C. Feed
Si < 4 % 60 HB 0.3 4.0 0.12 0.35 1.20 400 1200 22.3 0.23 4400
4% < Si < 8 % 100 HB 0.3 4.0 0.10 0.30 0.96 250 600 22.3 0.23 3300
Copper Alloys 14 26,27,28 CuZn30 100 HB 0.3 4.0 0.10 0.30 0.96 150 800 22.3 0.23 2250
29 Fiber Plastics - 0.3 4.0 0.10 0.20 0.96 70 500 11.8 0.15 1150
30 Hard Rubber - 0.3 4.0 0.10 0.20 0.96 80 300 11.8 0.15 1150
- Graphite - 0.3 4.0 0.10 0.20 0.96 100 200 11.8 0.15 1150
36 Ti 1 - 0.3 2.0 0.09 0.16 0.22 35 60 11.4 0.13 445
37 TiAl 6 V4 - 0.3 2.0 0.12 0.20 0.19 28 40 11.4 0.12 33510
1321, 22 23,
24
15
WNGG 080404 ALU – LT 05
min max min max min max D.O.C. Feed
Si < 4 % 60 HB 0.3 4.0 0.12 0.35 1.20 400 1200 22.3 0.23 4400
4% < Si < 8 % 100 HB 0.3 4.0 0.10 0.30 0.96 250 600 22.3 0.23 3300
Copper Alloys 14 26,27,28 CuZn30 100 HB 0.3 4.0 0.10 0.30 0.96 150 800 22.3 0.23 2250
29 Fiber Plastics - 0.3 4.0 0.10 0.20 0.96 70 500 11.8 0.15 1150
30 Hard Rubber - 0.3 4.0 0.10 0.20 0.96 80 300 11.8 0.15 1150
- Graphite - 0.3 4.0 0.10 0.20 0.96 100 200 11.8 0.15 1150
36 Ti 1 - 0.3 2.0 0.09 0.16 0.22 35 60 11.4 0.13 445
37 TiAl 6 V4 - 0.3 2.0 0.12 0.20 0.19 28 40 11.4 0.12 33510
1321, 22 23,
24
15
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
H.T.
A
Ti Based Alloys
NF
Al (<8%Si)
Copper Alloys
Non-Metallic
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
H.T.
A
Ti Based Alloys
NF
Al (<8%Si)
Copper Alloys
Non-Metallic
176
PARTING & GROOVING
177
PARTING & GROOVING
LT 1000 | LT 10PARTING &GROOVING
PARTING
178
PARTING & GROOVING
Parting : (P)d.o.c. =
fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev
Grooving: (G)d.o.c. =
fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev
Side Turning : (ST)d.o.c. =
fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev
= Good = Acceptable
Application Guide
Machining Recommendations Application Guide
G C T XShape
"Dog bone"Clearance Angle Insert Type
SpecialTolerance
d ± 0.05m ± 0.16s ± 0.13
C = 7° Rake angle
P G STInsert Designation R Catalog Nr.W
LT 1000 Multi-MatTM General Usage - Premium
T0002826
T0002828
0.25
0.25
3.00
3.00
GCTX 3003 NN LT 1000
GCTX 3003 PP LT 1000
T00028250.182.00GCTX 2002 NN LT 1000
= Not recommended
PP: All-purpose chipbreaker NN: For steel and cast iron
P G STInsert Designation R Catalog Nr.W
LT 10 Multi-MatTM General Usage - Standard
T0003910
T0003921
T0003911
0.40
0.80
0.40
3.00
5.00
4.00
MGMN 300 M LT 10
MGMN 500 M LT 10
MGMN 400 M LT 10
T00039090.202.00MGMN 200 G LT 10
P G STInsert Designation R Catalog Nr.W
LT 10 Multi-MatTM General Usage - Standard
T0003933
T0003935
T0003934
0.20
0.20
0.20
3.00
5.00
4.00
WGE 3000 LT 10
WGE 5000 LT 10
WGE 4000 LT 10
T00039320.202.00WGE 2000 LT 10
Application Guide
Application Guide
Details on page 14
179
PARTING & GROOVING
LT PNG-L 12-2.0 T200116412 12 120 1.6 15 Left
LT PNG-L 16-3.0 T200116816 16 120 2.4 15 Left
LT PNG-R 12-2.0 T200116512 12 120 1.6 15 Right
LT PNG-R 16-3.0 T200116916 16 120 2.4 15 Right
LT PNG-L 16-2.0 T200116616 16 120 1.6 15 Left
LT PNG-L 20-3.0 T200117020 20 125 2.4 15 Left
LT PNG-R 16-2.0 T200116716 16 120 1.6 15 Right
LT PNG-R 20-3.0 T200117120 20 125 2.4 15 Right
LT PNG-L 20-2.0 T200148420 20 120 1.6 15 Left
LT PNG-L 25-3.0 T200119725 25 125 2.4 15 Left
LT PNG-R 20-2.0 T200148520 20 120 1.6 15 Right
LT PNG-R 25-3.0 T200119825 25 125 2.4 15 Right
LT PNG-L 25-2.0 T200148225 25 120 1.6 15 Left
LT PNG-R 25-2.0 T200148325 25 120 1.6 15 Right
Designation D1 Catalog Nr.HandD2 L W Pmax
Designation D1 Catalog Nr.HandD2 L W Pmax
Parting Tool Holders for GCTX 2002
Parting Tool Holders for GCTX 3003
Screw:
Screw:
Key:
Key:
M2001797
M2001797
M2000609
M2000609
180
PARTING & GROOVING
LT BNG-32-3 T2002751145 32
Designation Catalog Nr.L H
LT PNB-N 2020-32 T200276232 20 4819 38 120
LT PNB-N 2525-32 T200276332 25 4823 42 120
Designation Catalog Nr.H A TB C L
Blocks
Blades
L
H
L
AT H
BC
Screw:
Key:
Key:
T2002785
T2002761
T2002786
Machining Conditions
181
PARTING & GROOVING
GCTX 2002 NN – LT 1000
min max min max Feed
1 125 HB 0.05 0.17 130 220 00.11 175
2 190 HB 0.05 0.17 130 220 00.11 175
3 250 HB 0.05 0.17 130 200 00.11 165
6 180 HB 0.05 0.15 90 200 00.10 145
4,6 230 HB 0.05 0.15 90 200 00.10 145
5,7 280 HB 0.05 0.15 90 170 00.10 130
8 350 HB 0.05 0.15 90 150 00.10 120
10 220 HB 0.05 0.14 60 170 00.10 115
10 280 HB 0.05 0.14 60 150 00.10 105
11 320 HB 0.05 0.13 60 130 00.09 95
11 350 HB 0.05 0.12 60 100 00.09 80
14 180 HB 0.05 0.10 90 150 00.07 120
14 240 HB 0.05 0.10 70 140 00.07 105
14 290 HB 0.05 0.09 60 100 00.07 80
14 310 HB 0.05 0.09 60 100 00.07 80
12 200 HB 0.05 0.09 60 130 00.07 95
13 42 HRc 0.05 0.08 50 90 00.07 70
15 150 HB 0.05 0.16 130 190 00.11 160
15 200 HB 0.05 0.16 130 190 00.11 160
16 250 HB 0.05 0.16 130 190 00.11 160
17,19 150 HB 0.05 0.14 90 150 00.10 120
17,19 200 HB 0.05 0.14 90 150 00.10 120
18,20 250 HB 0.05 0.14 90 150 00.10 120
31,32 Incoloy 800 240 HB 0.05 0.08 25 35 00.07 30
33 Inconel 700 250 HB 0.05 0.08 25 35 00.07 30
34 Stellite 21 350 HB 0.05 0.08 23 35 00.07 29
36 TiAl6V4 - 0.05 0.08 35 60 00.07 45
37 T40 - 0.05 0.08 28 40 00.07 34
38 45 HRc 0.05 0.11 50 90 00.08 70
38 50 HRc 0.05 0.10 40 70 00.08 55
38 55 HRc 0.05 0.09 30 60 00.07 45
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.05 0.08 40 60 00.07 50
White Cast Iron 41 G-X300CrMo15 55 HRc 0.05 0.08 30 50 00.07 40
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.05 0.10 100 300 0.08 200
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]
min max min max min maxMaterial Group Gr. N° VDI
GroupMaterial Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
182
PARTING & GROOVING Machining Conditions
GCTX 3003 NN – LT 1000
min max min max Feed
1 125 HB 0.07 0.20 130 220 00.14 175
2 190 HB 0.07 0.20 130 220 00.14 175
3 250 HB 0.07 0.20 130 200 00.14 165
6 180 HB 0.07 0.18 90 200 00.13 145
4,6 230 HB 0.07 0.18 90 200 00.13 145
5,7 280 HB 0.07 0.18 90 170 00.13 130
8 350 HB 0.07 0.18 90 150 00.13 120
10 220 HB 0.07 0.17 60 170 00.12 115
10 280 HB 0.07 0.17 60 150 00.12 105
11 320 HB 0.07 0.16 60 130 00.11 95
11 350 HB 0.07 0.14 60 100 00.11 80
14 180 HB 0.07 0.12 90 150 00.09 120
14 240 HB 0.07 0.12 70 140 00.09 105
14 290 HB 0.07 0.11 60 100 00.09 80
14 310 HB 0.07 0.11 60 100 00.09 80
12 200 HB 0.07 0.11 60 130 00.09 95
13 42 HRc 0.07 0.10 50 90 00.08 70
15 150 HB 0.07 0.19 130 190 00.13 160
15 200 HB 0.07 0.19 130 190 00.13 160
16 250 HB 0.07 0.19 130 190 00.13 160
17,19 150 HB 0.07 0.17 90 150 00.12 120
17,19 200 HB 0.07 0.17 90 150 00.12 120
18,20 250 HB 0.07 0.17 90 150 00.12 120
31,32 Incoloy 800 240 HB 0.07 0.10 25 35 00.08 30
33 Inconel 700 250 HB 0.07 0.10 25 35 00.08 30
34 Stellite 21 350 HB 0.07 0.10 23 35 00.08 29
36 TiAl6V4 - 0.07 0.10 35 60 00.08 45
37 T40 - 0.07 0.10 28 40 00.08 34
38 45 HRc 0.07 0.13 50 90 00.10 70
38 50 HRc 0.07 0.12 40 70 00.10 55
38 55 HRc 0.07 0.11 30 60 00.09 45
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.07 0.10 40 60 00.08 50
White Cast Iron 41 G-X300CrMo15 55 HRc 0.07 0.10 30 50 00.08 40
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.07 0.12 100 300 00.10 200
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3X40CrMoV5,
H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C, G-
X260NiCr4211
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]
min max min max min maxMaterial Group Gr. N° VDI
GroupMaterial Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Machining Conditions
183
PARTING & GROOVING
GCTX 3003 PP – LT 1000
min max min max Feed
1 125 HB 0.05 0.17 130 220 00.11 175
2 190 HB 0.05 0.17 130 220 00.11 175
3 250 HB 0.05 0.17 130 200 00.11 165
6 180 HB 0.05 0.15 90 200 00.10 145
4,6 230 HB 0.05 0.15 90 200 00.10 145
5,7 280 HB 0.05 0.15 90 170 00.10 130
8 350 HB 0.05 0.15 90 150 00.10 120
10 220 HB 0.05 0.14 60 170 00.10 115
10 280 HB 0.05 0.14 60 150 00.10 105
11 320 HB 0.05 0.13 60 130 00.09 95
11 350 HB 0.05 0.12 60 100 00.09 80
14 180 HB 0.05 0.10 90 150 00.07 120
14 240 HB 0.05 0.10 70 140 00.07 105
14 290 HB 0.05 0.09 60 100 00.07 80
14 310 HB 0.05 0.09 60 100 00.07 80
12 200 HB 0.05 0.09 60 130 00.07 95
13 42 HRc 0.05 0.08 50 90 00.07 70
15 150 HB 0.05 0.16 130 190 00.11 160
15 200 HB 0.05 0.16 130 190 00.11 160
16 250 HB 0.05 0.16 130 190 00.11 160
17,19 150 HB 0.05 0.14 90 150 00.10 120
17,19 200 HB 0.05 0.14 90 150 00.10 120
18,20 250 HB 0.05 0.14 90 150 00.10 120
31,32 Incoloy 800 240 HB 0.05 0.08 25 35 00.07 30
33 Inconel 700 250 HB 0.05 0.08 25 35 00.07 30
34 Stellite 21 350 HB 0.05 0.08 23 35 00.07 29
36 TiAl6V4 - 0.05 0.08 35 60 00.07 45
37 T40 - 0.05 0.08 28 40 00.07 34
38 45 HRc 0.05 0.11 50 90 00.08 70
38 50 HRc 0.05 0.10 40 70 00.08 55
38 55 HRc 0.05 0.09 30 60 00.07 45
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.05 0.08 40 60 00.07 50
White Cast Iron 41 G-X300CrMo15 55 HRc 0.05 0.08 30 50 00.07 40
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.05 0.10 100 300 0.08 200
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3X40CrMoV5,
H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316, X5CrNi18-
9
Duplex 5X2CrNiN23-4,
S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]
min max min max min maxMaterial Group Gr. N° VDI
GroupMaterial Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
184
PARTING & GROOVING Machining Conditions
MGMN 200 G – LT 10
min max min max min max D.O.C. Feed
1 125 HB 0.3 1.5 0.09 0.18 0.21 110 210 11.0 0.11 1160
2 190 HB 0.3 1.3 0.09 0.18 0.18 110 180 11.0 0.11 1150
3 250 HB 0.3 1.3 0.09 0.16 0.17 110 160 11.0 0.11 1140
6 180 HB 0.3 1.3 0.08 0.16 0.18 70 180 11.0 0.09 1130
4,6 230 HB 0.3 1.3 0.08 0.16 0.17 70 160 11.0 0.09 1120
5,7 280 HB 0.3 1.0 0.08 0.14 0.14 70 140 11.0 0.09 1110
8 350 HB 0.3 1.0 0.08 0.14 0.13 70 120 11.0 0.09 1100
10 220 HB 0.3 1.3 0.07 0.14 0.14 40 120 11.0 0.07 880
10 280 HB 0.3 1.3 0.07 0.13 0.14 40 100 11.0 0.07 770
11 320 HB 0.3 1.0 0.07 0.11 0.11 40 80 11.0 0.07 660
11 350 HB 0.3 1.0 0.07 0.11 0.09 40 70 11.0 0.07 660
14 180 HB 0.3 1.3 0.08 0.14 0.11 100 180 11.0 0.07 1140
14 240 HB 0.3 1.3 0.08 0.14 0.09 100 140 11.0 0.07 1120
14 290 HB 0.3 1.0 0.07 0.11 0.07 50 100 11.0 0.07 880
14 310 HB 0.3 1.0 0.07 0.11 0.07 40 90 11.0 0.07 770
12 200 HB 0.3 1.3 0.08 0.14 0.11 100 160 11.0 0.09 1130
13 42 HRc 0.3 1.0 0.08 0.13 0.09 70 120 11.0 0.07 1100
15 150 HB 0.3 1.5 0.06 0.16 0.22 100 160 11.0 0.11 1130
15 200 HB 0.3 1.5 0.06 0.16 0.21 100 150 11.0 0.11 1130
16 250 HB 0.3 1.5 0.06 0.16 0.21 90 140 11.0 0.11 1120
17,19 150 HB 0.3 1.3 0.06 0.14 0.17 70 160 11.0 0.09 1120
17,19 200 HB 0.3 1.3 0.06 0.14 0.14 70 150 11.0 0.09 1110
18,20 250 HB 0.3 1.3 0.06 0.14 0.14 70 120 11.0 0.09 1100
31,32 Incoloy 800 240 HB 0.3 1.0 0.07 0.12 0.09 15 33 11.0 0.07 220
33 Inconel 700 250 HB 0.3 1.0 0.07 0.12 0.09 15 33 11.0 0.07 220
34 Stellite 21 350 HB 0.3 1.0 0.07 0.12 0.09 14 29 11.0 0.07 220
36 TiAl6V4 - 0.3 1.0 0.07 0.13 0.11 27 42 11.0 0.09 330
37 T40 - 0.3 1.0 0.07 0.11 0.09 21 39 11.0 0.07 330
38 45 HRc 0.3 0.9 0.04 0.10 0.07 30 65 00.8 0.07 550
38 50 HRc 0.3 0.8 0.04 0.08 0.06 24 59 00.6 0.06 440
38 55 HRc 0.3 0.7 0.04 0.07 0.05 24 52 00.5 0.04 440
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 0.8 0.04 0.10 0.06 24 39 00.6 0.07 330
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 0.7 0.04 0.07 0.05 18 33 00.5 0.04 330
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 2.0 0.08 0.24 0.25 120 260 1.0 0.12 190
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Machining Conditions
185
PARTING & GROOVING
MGMN 300 M – LT 10
min max min max min max D.O.C. Feed
1 125 HB 0.5 2.4 0.11 0.23 0.42 110 210 11.5 0.13 1160
2 190 HB 0.5 2.0 0.11 0.22 0.36 110 180 11.5 0.13 1150
3 250 HB 0.5 2.0 0.11 0.20 0.34 110 160 11.5 0.13 1140
6 180 HB 0.5 2.0 0.10 0.20 0.35 70 180 11.5 0.11 1130
4,6 230 HB 0.5 2.0 0.10 0.20 0.34 70 160 11.5 0.11 1120
5,7 280 HB 0.5 1.6 0.10 0.18 0.28 70 140 11.5 0.11 1110
8 350 HB 0.5 1.6 0.10 0.18 0.25 70 120 11.5 0.11 1100
10 220 HB 0.5 2.0 0.09 0.18 0.28 40 120 11.5 0.08 880
10 280 HB 0.5 2.0 0.09 0.16 0.28 40 100 11.5 0.08 770
11 320 HB 0.5 1.6 0.09 0.14 0.22 40 80 11.5 0.08 660
11 350 HB 0.5 1.6 0.09 0.14 0.18 40 70 11.5 0.08 660
14 180 HB 0.5 2.0 0.10 0.18 0.22 100 180 11.5 0.08 1140
14 240 HB 0.5 2.0 0.10 0.18 0.18 100 140 11.5 0.08 1120
14 290 HB 0.5 1.6 0.09 0.14 0.14 50 100 11.5 0.08 880
14 310 HB 0.5 1.6 0.09 0.14 0.14 40 90 11.5 0.08 770
12 200 HB 0.5 2.0 0.10 0.18 0.22 100 160 11.5 0.11 1130
13 42 HRc 0.5 1.6 0.10 0.16 0.18 70 120 11.5 0.08 1100
15 150 HB 0.5 2.4 0.08 0.20 0.45 100 160 11.5 0.13 1130
15 200 HB 0.5 2.4 0.08 0.20 0.42 100 150 11.5 0.13 1130
16 250 HB 0.5 2.4 0.08 0.20 0.42 90 140 11.5 0.13 1120
17,19 150 HB 0.5 2.0 0.08 0.18 0.34 70 160 11.5 0.11 1120
17,19 200 HB 0.5 2.0 0.08 0.18 0.28 70 150 11.5 0.11 1110
18,20 250 HB 0.5 2.0 0.08 0.18 0.28 70 120 11.5 0.11 1100
31,32 Incoloy 800 240 HB 0.5 1.6 0.09 0.15 0.18 15 33 11.5 0.08 220
33 Inconel 700 250 HB 0.5 1.6 0.09 0.15 0.18 15 33 11.5 0.08 220
34 Stellite 21 350 HB 0.5 1.6 0.09 0.15 0.18 14 29 11.5 0.08 220
36 TiAl6V4 - 0.5 1.6 0.09 0.16 0.22 27 42 11.5 0.11 330
37 T40 - 0.5 1.6 0.09 0.14 0.18 21 39 11.5 0.08 330
38 45 HRc 0.5 1.4 0.05 0.12 0.14 30 65 11.1 0.08 550
38 50 HRc 0.5 1.2 0.05 0.10 0.12 24 59 00.9 0.06 440
38 55 HRc 0.5 1.1 0.05 0.09 0.09 24 52 00.7 0.05 440
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 1.3 0.05 0.12 0.12 24 39 00.9 0.08 330
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.1 0.05 0.09 0.09 18 33 00.7 0.05 330
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.2 0.10 0.30 0.49 120 260 1.5 0.14 190
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5
7 GG20, GG40, EN-GJL-250,
No30B
8
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
186
PARTING & GROOVING Machining Conditions
MGMN 400 M – LT 10
min max min max min max D.O.C. Feed
1 125 HB 1.0 3.6 0.13 0.28 0.60 110 210 22.5 0.22 1160
2 190 HB 1.0 3.0 0.13 0.26 0.52 110 180 22.5 0.22 1150
3 250 HB 1.0 3.0 0.13 0.24 0.48 110 160 22.5 0.22 1140
6 180 HB 1.0 3.0 0.12 0.24 0.50 70 180 22.5 0.18 1130
4,6 230 HB 1.0 3.0 0.12 0.24 0.48 70 160 22.5 0.18 1120
5,7 280 HB 1.0 2.4 0.12 0.22 0.40 70 140 22.5 0.18 1110
8 350 HB 1.0 2.4 0.12 0.22 0.36 70 120 22.5 0.18 1100
10 220 HB 1.0 3.0 0.11 0.22 0.40 40 120 22.5 0.14 880
10 280 HB 1.0 3.0 0.11 0.19 0.40 40 100 22.5 0.14 770
11 320 HB 1.0 2.4 0.11 0.17 0.32 40 80 22.5 0.14 660
11 350 HB 1.0 2.4 0.11 0.17 0.26 40 70 22.5 0.14 660
14 180 HB 1.0 3.0 0.12 0.22 0.32 100 180 22.5 0.14 1140
14 240 HB 1.0 3.0 0.12 0.22 0.26 100 140 22.5 0.14 1120
14 290 HB 1.0 2.4 0.11 0.17 0.20 50 100 22.5 0.14 880
14 310 HB 1.0 2.4 0.11 0.17 0.20 40 90 22.5 0.14 770
12 200 HB 1.0 3.0 0.12 0.22 0.32 100 160 22.5 0.18 1130
13 42 HRc 1.0 2.4 0.12 0.19 0.26 70 120 22.5 0.14 1100
15 150 HB 1.0 3.6 0.10 0.24 0.64 100 160 22.5 0.22 1130
15 200 HB 1.0 3.6 0.10 0.24 0.60 100 150 22.5 0.22 1130
16 250 HB 1.0 3.6 0.10 0.24 0.60 90 140 22.5 0.22 1120
17,19 150 HB 1.0 3.0 0.10 0.22 0.48 70 160 22.5 0.18 1120
17,19 200 HB 1.0 3.0 0.10 0.22 0.40 70 150 22.5 0.18 1110
18,20 250 HB 1.0 3.0 0.10 0.22 0.40 70 120 22.5 0.18 1100
31,32 Incoloy 800 240 HB 1.0 2.4 0.11 0.18 0.26 15 33 22.5 0.14 220
33 Inconel 700 250 HB 1.0 2.4 0.11 0.18 0.26 15 33 22.5 0.14 220
34 Stellite 21 350 HB 1.0 2.4 0.11 0.18 0.26 14 29 22.5 0.14 220
36 TiAl6V4 - 1.0 2.4 0.11 0.19 0.32 27 42 22.5 0.18 330
37 T40 - 1.0 2.4 0.11 0.17 0.26 21 39 22.5 0.14 330
38 45 HRc 1.0 2.2 0.06 0.14 0.20 30 65 11.9 0.13 550
38 50 HRc 1.0 1.8 0.06 0.12 0.17 24 59 11.5 0.11 440
38 55 HRc 1.0 1.7 0.06 0.11 0.13 24 52 11.3 0.08 440
Chilled Cast Iron 40 Ni-Hard 2 400 HB 1.0 1.9 0.06 0.14 0.17 24 39 11.5 0.13 330
White Cast Iron 41 G-X300CrMo15 55 HRc 1.0 1.7 0.06 0.11 0.13 18 33 11.3 0.08 330
NF Al (>8%Si) 12 25 AlSi12 130 HB 1.0 4.8 0.12 0.36 0.70 120 260 2.5 0.24 190
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Machining Conditions
187
PARTING & GROOVING
MGMN 500 M – LT 10
min max min max min max D.O.C. Feed
1 125 HB 1.2 4.2 0.20 0.41 0.60 110 210 33.0 0.30 1160
2 190 HB 1.2 3.5 0.20 0.40 0.52 110 180 33.0 0.30 1150
3 250 HB 1.2 3.5 0.20 0.36 0.48 110 160 33.0 0.30 1140
6 180 HB 1.2 3.5 0.18 0.36 0.50 70 180 33.0 0.25 1130
4,6 230 HB 1.2 3.5 0.18 0.36 0.48 70 160 33.0 0.25 1120
5,7 280 HB 1.2 2.8 0.18 0.32 0.40 70 140 33.0 0.25 1110
8 350 HB 1.2 2.8 0.18 0.32 0.36 70 120 33.0 0.25 1100
10 220 HB 1.2 3.5 0.16 0.32 0.40 40 120 33.0 0.20 880
10 280 HB 1.2 3.5 0.16 0.29 0.40 40 100 33.0 0.20 770
11 320 HB 1.2 2.8 0.16 0.25 0.32 40 80 33.0 0.20 660
11 350 HB 1.2 2.8 0.16 0.25 0.26 40 70 33.0 0.20 660
14 180 HB 1.2 3.5 0.18 0.32 0.32 100 180 33.0 0.20 1140
14 240 HB 1.2 3.5 0.18 0.32 0.26 100 140 33.0 0.20 1120
14 290 HB 1.2 2.8 0.16 0.25 0.20 50 100 33.0 0.20 880
14 310 HB 1.2 2.8 0.16 0.25 0.20 40 90 33.0 0.20 770
12 200 HB 1.2 3.5 0.18 0.32 0.32 100 160 33.0 0.25 1130
13 42 HRc 1.2 2.8 0.18 0.29 0.26 70 120 33.0 0.20 1100
15 150 HB 1.2 4.2 0.14 0.36 0.64 100 160 33.0 0.30 1130
15 200 HB 1.2 4.2 0.14 0.36 0.60 100 150 33.0 0.30 1130
16 250 HB 1.2 4.2 0.14 0.36 0.60 90 140 33.0 0.30 1120
17,19 150 HB 1.2 3.5 0.14 0.32 0.48 70 160 33.0 0.25 1120
17,19 200 HB 1.2 3.5 0.14 0.32 0.40 70 150 33.0 0.25 1110
18,20 250 HB 1.2 3.5 0.14 0.32 0.40 70 120 33.0 0.25 1100
31,32 Incoloy 800 240 HB 1.2 2.8 0.16 0.27 0.26 15 33 33.0 0.20 220
33 Inconel 700 250 HB 1.2 2.8 0.16 0.27 0.26 15 33 33.0 0.20 220
34 Stellite 21 350 HB 1.2 2.8 0.16 0.27 0.26 14 29 33.0 0.20 220
36 TiAl6V4 - 1.2 2.8 0.16 0.29 0.32 27 42 33.0 0.25 330
37 T40 - 1.2 2.8 0.16 0.25 0.26 21 39 33.0 0.20 330
38 45 HRc 1.2 2.5 0.09 0.22 0.20 30 65 22.3 0.18 550
38 50 HRc 1.2 2.1 0.09 0.18 0.17 24 59 11.8 0.15 440
38 55 HRc 1.2 2.0 0.09 0.16 0.13 24 52 11.5 0.12 440
Chilled Cast Iron 40 Ni-Hard 2 400 HB 1.2 2.2 0.09 0.22 0.17 24 39 11.8 0.18 330
White Cast Iron 41 G-X300CrMo15 55 HRc 1.2 2.0 0.09 0.16 0.13 18 33 11.5 0.12 330
NF Al (>8%Si) 12 25 AlSi12 130 HB 1.2 5.6 0.18 0.54 0.70 120 260 3.0 0.33 190
St
eel
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Stai
nles
s St
eel
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Mat
.
Steel
11
GGG40, GGG70, 50005
High
Tem
p.Al
loys
Fe, Ni & Co based
9
Ti based 10
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Cast
Iron
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
188
PARTING & GROOVING Machining Conditions
WGE 2000 – LT 10
min max min max Feed
1 125 HB 0.04 0.12 110 215 00.09 160
2 190 HB 0.04 0.11 110 180 00.09 150
3 250 HB 0.04 0.10 110 165 00.09 140
6 180 HB 0.04 0.10 70 180 00.08 130
4,6 230 HB 0.04 0.10 70 165 00.08 120
5,7 280 HB 0.04 0.09 70 135 00.08 110
8 350 HB 0.04 0.09 70 115 00.08 100
10 220 HB 0.04 0.09 40 125 00.06 80
10 280 HB 0.04 0.08 40 100 00.06 70
11 320 HB 0.04 0.07 40 85 00.06 60
11 350 HB 0.04 0.07 40 70 00.06 60
14 180 HB 0.04 0.09 100 175 00.06 140
14 240 HB 0.04 0.09 95 145 00.06 120
14 290 HB 0.04 0.07 50 100 00.06 80
14 310 HB 0.04 0.07 40 90 00.06 70
12 200 HB 0.04 0.09 100 165 00.07 110
13 42 HRc 0.04 0.08 70 125 00.06 70
15 150 HB 0.03 0.10 100 165 00.09 130
15 200 HB 0.03 0.10 95 150 00.09 130
16 250 HB 0.03 0.10 90 135 00.09 120
17,19 150 HB 0.03 0.09 70 165 00.08 120
17,19 200 HB 0.03 0.09 70 150 00.08 110
18,20 250 HB 0.03 0.09 70 125 00.08 100
31,32 Incoloy 800 240 HB 0.04 0.08 15 35 00.06 20
33 Inconel 700 250 HB 0.04 0.08 15 35 00.06 20
34 Stellite 21 350 HB 0.04 0.08 15 30 00.06 20
36 TiAl6V4 - 0.04 0.08 25 40 00.08 30
37 T40 - 0.04 0.07 20 40 00.06 30
38 45 HRc 0.03 0.06 30 65 00.06 50
38 50 HRc 0.03 0.05 25 60 00.05 40
38 55 HRc 0.03 0.05 25 50 00.04 40
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.03 0.06 25 40 00.06 30
White Cast Iron 41 G-X300CrMo15 55 HRc 0.03 0.05 20 35 00.04 30
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.04 0.15 120 260 0.10 190
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]
min max min max min maxMaterial Group Gr. N° VDI
GroupMaterial Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Machining Conditions
189
PARTING & GROOVING
WGE 3000 – LT 10
min max min max Feed
1 125 HB 0.07 0.24 110 215 00.12 160
2 190 HB 0.07 0.23 110 180 00.12 150
3 250 HB 0.07 0.21 110 165 00.12 140
6 180 HB 0.06 0.21 70 180 00.10 130
4,6 230 HB 0.06 0.21 70 165 00.10 120
5,7 280 HB 0.06 0.19 70 135 00.10 110
8 350 HB 0.06 0.19 70 115 00.10 100
10 220 HB 0.05 0.19 40 125 00.08 80
10 280 HB 0.05 0.17 40 100 00.08 70
11 320 HB 0.05 0.15 40 85 00.08 60
11 350 HB 0.05 0.15 40 70 00.08 60
14 180 HB 0.06 0.19 100 175 00.08 140
14 240 HB 0.06 0.19 95 145 00.08 120
14 290 HB 0.05 0.15 50 100 00.08 80
14 310 HB 0.05 0.15 40 90 00.08 70
12 200 HB 0.06 0.19 100 165 00.09 110
13 42 HRc 0.06 0.17 70 125 00.08 70
15 150 HB 0.05 0.21 100 165 00.12 130
15 200 HB 0.05 0.21 95 150 00.12 130
16 250 HB 0.05 0.21 90 135 00.12 120
17,19 150 HB 0.05 0.19 70 165 00.10 120
17,19 200 HB 0.05 0.19 70 150 00.10 110
18,20 250 HB 0.05 0.19 70 125 00.10 100
31,32 Incoloy 800 240 HB 0.05 0.16 15 35 00.08 20
33 Inconel 700 250 HB 0.05 0.16 15 35 00.08 20
34 Stellite 21 350 HB 0.05 0.16 15 30 00.08 20
36 TiAl6V4 - 0.05 0.17 25 40 00.10 30
37 T40 - 0.05 0.15 20 40 00.08 30
38 45 HRc 0.03 0.13 30 65 00.07 50
38 50 HRc 0.03 0.11 25 60 00.06 40
38 55 HRc 0.03 0.09 25 50 00.05 40
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.03 0.13 25 40 00.07 30
White Cast Iron 41 G-X300CrMo15 55 HRc 0.03 0.09 20 35 00.05 30
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.06 0.32 120 260 0.13 190
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]
min max min max min maxMaterial Group Gr. N° VDI
GroupMaterial Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
190
PARTING & GROOVING Machining Conditions
WGE 4000 – LT 10
min mmax min mmax Feed Vcc
1 125 HB 0.08 0.26 110 215 00.14 160
2 190 HB 0.08 0.25 110 180 00.14 150
3 250 HB 0.08 0.23 110 165 00.14 140
6 180 HB 0.07 0.23 70 180 00.12 130
4,6 230 HB 0.07 0.23 70 165 00.12 120
5,7 280 HB 0.07 0.21 70 135 00.12 110
8 350 HB 0.07 0.21 70 115 00.12 100
10 220 HB 0.06 0.21 40 125 00.10 80
10 280 HB 0.06 0.18 40 100 00.10 70
11 320 HB 0.06 0.16 40 85 00.10 60
11 350 HB 0.06 0.16 40 70 00.10 60
14 180 HB 0.07 0.21 100 175 00.10 140
14 240 HB 0.07 0.21 95 145 00.10 120
14 290 HB 0.06 0.16 50 100 00.10 80
14 310 HB 0.06 0.16 40 90 00.10 70
12 200 HB 0.07 0.21 100 165 00.11 110
13 42 HRc 0.07 0.18 70 125 00.10 70
15 150 HB 0.06 0.23 100 165 00.14 130
15 200 HB 0.06 0.23 95 150 00.14 130
16 250 HB 0.06 0.23 90 135 00.14 120
17,19 150 HB 0.06 0.21 70 165 00.12 120
17,19 200 HB 0.06 0.21 70 150 00.12 110
18,20 250 HB 0.06 0.21 70 125 00.12 100
31,32 Incoloy 800 240 HB 0.06 0.17 15 35 00.10 20
33 Inconel 700 250 HB 0.06 0.17 15 35 00.10 20
34 Stellite 21 350 HB 0.06 0.17 15 30 00.10 20
36 TiAl6V4 - 0.06 0.18 25 40 00.12 30
37 T40 - 0.06 0.16 20 40 00.10 30
38 45 HRc 0.04 0.14 30 65 00.09 50
38 50 HRc 0.04 0.12 25 60 00.07 40
38 55 HRc 0.04 0.10 25 50 00.06 40
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.04 0.14 25 40 00.09 30
White Cast Iron 41 G-X300CrMo15 55 HRc 0.04 0.10 20 35 00.06 30
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.07 0.35 120 260 0.16 190
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Gr. N°VDI
GroupMaterial Examples* Hardness
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
Unlegiert
Stah
l Niedriglegiert
Hochlegiert
Edel
stah
l
Austenitisch
Duplex
Ferritisch &Martensitisch
Guss
eise
n Grau
Sphäroguss
Supe
rleg.
Fe, Ni & Co-basiert
Ti-basiert
Gehä
rtete
s M
at.
Stahl
Schalenhartguss
Weißes Guss.
NE Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]
min max min max min maxMaterialgruppe Gr. N° ISO Materialbsp. Härte
fn [mm/U] Vc [m/min] EmpfohleneStartbedingungen
min max min max fn Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]
min max min max min maxMaterial Group Gr. N° VDI
GroupMaterial Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Machining Conditions
191
PARTING & GROOVING
WGE 5000 – LT 10
min max min max Feed
1 125 HB 0.08 0.30 110 215 00.16 160
2 190 HB 0.08 0.29 110 180 00.16 150
3 250 HB 0.08 0.26 110 165 00.16 140
6 180 HB 0.07 0.26 70 180 00.14 130
4,6 230 HB 0.07 0.26 70 165 00.14 120
5,7 280 HB 0.07 0.23 70 135 00.14 110
8 350 HB 0.07 0.23 70 115 00.14 100
10 220 HB 0.06 0.23 40 125 00.11 80
10 280 HB 0.06 0.21 40 100 00.11 70
11 320 HB 0.06 0.18 40 85 00.11 60
11 350 HB 0.06 0.18 40 70 00.11 60
14 180 HB 0.07 0.23 100 175 00.11 140
14 240 HB 0.07 0.23 95 145 00.11 120
14 290 HB 0.06 0.18 50 100 00.11 80
14 310 HB 0.06 0.18 40 90 00.11 70
12 200 HB 0.07 0.23 100 165 00.13 110
13 42 HRc 0.07 0.21 70 125 00.11 70
15 150 HB 0.06 0.26 100 165 00.16 130
15 200 HB 0.06 0.26 95 150 00.16 130
16 250 HB 0.06 0.26 90 135 00.16 120
17,19 150 HB 0.06 0.23 70 165 00.14 120
17,19 200 HB 0.06 0.23 70 150 00.14 110
18,20 250 HB 0.06 0.23 70 125 00.14 100
31,32 Incoloy 800 240 HB 0.06 0.20 15 35 00.11 20
33 Inconel 700 250 HB 0.06 0.20 15 35 00.11 20
34 Stellite 21 350 HB 0.06 0.20 15 30 00.11 20
36 TiAl6V4 - 0.06 0.21 25 40 00.14 30
37 T40 - 0.06 0.18 20 40 00.11 30
38 45 HRc 0.04 0.16 30 65 00.10 50
38 50 HRc 0.04 0.13 25 60 00.08 40
38 55 HRc 0.04 0.12 25 50 00.06 40
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.04 0.16 25 40 00.10 30
White Cast Iron 41 G-X300CrMo15 55 HRc 0.04 0.12 20 35 00.06 30
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.07 0.39 120 260 0.18 190
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]
min max min max min maxMaterial Group Gr. N° VDI
GroupMaterial Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
192
THREAD TURNING
193
THREAD TURNING
THREAD TURNING
Thread TurningThread Turning
194
THREAD TURNING
ISO 1.5 Grade16ERProfile
Partial Profile Partial Profile
Full Profile
mm tpi
Full Profile
ISO METRICUNWHITWORTHBSPTMJ
AGAGNQ
0.5-1.51.75-3.00.5-3.03.5-5.05.5-6.0
48-1614-848-87-54.5-4
NPTNPTFTRAPEZACMESTUB ACMEAM. BUTTRESSROUND (DIN 405)DIN 20400PGSAGENGWINDEUNJAPIAPI ROUNDBUT. CASINGEXTREME LINE
60°55°
2M3M
Pitch LT 10Insert sizeType ofinsert
Multitooth
V
L I.C.06
08
11
16
22
27
4.00
5.00
6.35
9.525
12.70
15.875
mm tpi0.35-6.0 72-4
Verti
cal
HERExternal right handed
HELExternal left handed
HIRInternal right handed
HILInternal left handed
Insert Ordering Code
Partial and Full Profiles
Partial Profile:
Most economical solution.
Used for wide range of pitches.
It is partial because the exterior major or internal minor diameter is not machined.
Full profile:
Cuts all thread shapes, according to the requirements.
Wide range of inserts needed in order to fit each standard and range of pitches.
Lamina threading line provides a large range of high quality standard threading inserts.
195
THREAD TURNING
Designation Catalog Nr.
Partial Profile 60°
Designation Catalog Nr.
Partial Profile 55°
EX / IN Grade
EX / IN Grade
A60 IR11 TH000001LT 10
AG55 ER16
N55 ER22
TH000022
TH000120
LT 10
LT 10
AG55 IR16
N55 IR22
TH000025
TH000121
Dimensions
L mm I.C. A B
16
22
9.525
12.70
1.2
1.7
1.7
2.5
16
22
9.525
12.70
1.2
1.7
1.7
2.5
Pitch Range
mm TPI
48 - 8
7 - 5
0.5 - 3.0
3.5 - 5.0
48 - 8
7 - 5
0.5 - 3.0
3.5 - 5.0
LT 10
LT 10
A60 IR16 TH000007LT 10
G60 ER16 TH000010LT 10
G60 IR16 TH000013LT 10
AG60 ER16 TH000016LT 10
AG60 IR16 TH000019LT 10
BA
I.C.
L
External Right
60°
Partial Profile 60° Internal Right
BA
I.C.
L
BA
I.C.
L
External Right
55°
Partial Profile 55° Internal Right
BA
I.C.
L
A60 ER16 TH000004
Pitch Range
mm TPI
0.5 - 1.5 48 - 16
0.5 - 1.5 48 - 16
1.75 - 3.0 14 - 8
1.75 - 3.0 14 - 8
0.5 - 3.0 48 - 8
0.5 - 3.0 48 - 8
0.5 - 1.5 48 - 16
Dimensions
L mm I.C. A B
0.911 6.35 0.8
0.916 9.525 0.8
1.716 9.525 1.2
1.716 9.525 1.2
1.716 9.525 1.2
1.716 9.525 1.2
0.916 9.525 0.8LT 10
196
THREAD TURNING
ISO METRIC
Internal RightExternal Right ISO Metric ISO 965-1:1999-11DIN 13: 2005-08
Designation Catalog Nr.
EX / IN Grade
Pitch
mm
Dimensions
BA
I.C.
L
60°
1/8P
1/4PB
A
I.C.
L
ISO 1.0 IR11
ISO 0.5 ER16
ISO 0.7 ER16
ISO 0.8 IR16
TH000028
TH000122
TH000124
TH000132
ISO 1.5 IR11
ISO 0.5 IR16
ISO 0.7 IR16
TH000031
TH000128
TH000130
ISO 2.0 IR11
ISO 0.6 ER16
ISO 0.75 ER16
TH000034
TH000123
TH000125
ISO 1.0 ER16
ISO 0.6 IR16
ISO 0.75 IR16
ISO 1.0 ER16
TH000037
TH000129
TH000131
TH000037
ISO 1.0 IR16 TH000040
ISO 1.25 ER16 TH000043
ISO 1.25 IR16 TH000046
ISO 1.5 ER16 TH000049
ISO 1.5 IR16 TH000052
ISO 1.75 ER16 TH000055
ISO 1.75 IR16 TH000056
ISO 2.0 ER16 TH000058
ISO 2.0 IR16 TH000061
ISO 2.5 ER16 TH000064
ISO 2.5 IR16 TH000067
ISO 3.0 ER16
ISO 3.5 ER22
ISO 4.0 IR22
TH000070
TH000126
TH000133
ISO 3.0 IR16
ISO 4.0 ER22
TH000073
TH000127
A BI.C.
6.350
9.525
9.525
9.525
6.350
9.525
9.525
6.350
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
12.70
12.70
9.525
12.70
0.7
0.6
0.6
0.6
0.8
0.6
0.6
0.8
0.6
0.6
0.7
0.6
0.6
0.7
0.7
0.8
0.8
0.8
0.8
0.9
0.9
1.0
1.0
1.1
1.1
1.2
1.6
1.6
1.2
1.6
0.7
0.4
0.4
0.6
1.0
0.4
0.6
0.9
0.4
0.6
0.7
0.6
0.6
0.7
0.7
0.9
0.9
1.0
1.0
1.2
1.2
1.3
1.3
1.5
1.5
1.5
2.3
2.3
1.5
2.3
1.00
0.50
0.70
0.80
1.50
0.50
0.70
2.00
0.60
0.75
1.00
0.60
0.75
1.00
1.00
1.25
1.25
1.50
1.50
1.75
1.75
2.00
2.00
2.50
2.50
3.00
3.50
4.00
3.00
4.00
L mm
11
16
16
16
11
16
16
11
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
22
22
16
22
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
LT10
197
THREAD TURNING
TRAPEZ
Internal RightISO Metric ISO 965-1:1999-11DIN 13: 2005-08
External Right
Designation Catalog Nr.
BA
I.C.
L
BA
I.C.
L
TR3.0 ER16 TH000149
TR3.0 IR16 TH000151
TR4.0 ER22 TH000150
TR4.0 IR22 TH000152
EX / IN
Pitch
3.00
3.00
4.00
4.00
mm
Dimensions
16
16
22
22
L mm
9.525
9.525
12.70
12.70
I.C.
1.3
1.3
1.7
1.7
A
1.5
1.5
1.9
1.9
B
LT10
LT10
LT10
LT10
Grade
TR NUT
TR SCREW
30°
198
THREAD TURNING
BA
I.C.
L
BA
I.C.
L
55°
R 0.137P
R 0.137P
BSW, BSF, BSP B.S.84: 1956ISO 228-1: 1994
60°
1/8P
1/4P
External Right Internal Right
UNC, UNF, UNEFANSI B1.1-1982External Right Internal Right
BA
I.C.
L
BA
I.C.
L
Designation Catalog Nr.
UN
UN 20 ER16 TH000076
UN 20 IR16 TH000079
UN 16 ER16 TH000082
UN 16 IR16 TH000085
UN 12 ER16 TH000088
UN 12 IR16 TH000091
EX / IN
Pitch
20
20
16
16
12
12
TPI
Dimensions
16
16
16
16
16
16
L mm
9.525
9.525
9.525
9.525
9.525
9.525
I.C.
0.8
0.8
0.9
0.9
1.1
1.1
A
0.9
0.9
1.1
1.1
1.4
1.4
B
LT10
LT10
LT10
LT10
LT10
LT10
Grade
Designation Catalog Nr.
WHITWORTH
W 14 ER16 TH000094
W 14 IR16 TH000097
W 19 ER16 TH000134
W 11 ER16 TH000100
W 19 IR16 TH000135
W 11 IR16 TH000103
EX / IN
Pitch
14
14
19
11
19
11
TPI
Dimensions
16
16
16
16
16
16
L mm
9.525
9.525
9.525
9.525
9.525
9.525
I.C.
1.0
1.0
0.8
1.1
0.8
1.1
A
1.2
1.2
1.0
1.5
1.0
1.5
B
LT10
LT10
LT10
LT10
LT10
LT10
Grade
199
THREAD TURNING
BA
I.C.
L
Internal Right
BA
I.C.
L
UNC, UNF, UNEFANSI B1.1-1982
30°
90° 1°47’
30°
External Right Internal Right
BA
I.C.
L
External Right
BA
I.C.
L
Designation Catalog Nr.
NPT
NPT8 ER16 TH000145
NPT8 IR16 TH000148
NPT11.5 ER16 TH000144
NPT11.5 ER16 TH000147
NPT14 ER16 TH000143
NPT14 IR16
NPT18 ER16
TH000146
TH000142
EX / IN
Pitch
8
8
11.5
11.5
14
14
18
TPI
16
16
16
16
16
16
16
L mm
Dimensions
9.525
9.525
9.525
9.525
9.525
9.525
9.525
I.C.
1.3
1.3
1.1
1.1
0.9
0.9
0.8
A
1.8
1.8
1.5
1.5
1.2
1.2
1.0
B
LT10
LT10
LT10
LT10
LT10
LT10
LT10
Grade
Designation Catalog Nr.
BSPT
BSPT14 ER16 TH000137
BSPT14 IR16 TH000140
BSPT19 ER16 TH000136
BSPT11 ER16 TH000138
BSPT19 IR16 TH000139
BSPT11 IR16 TH000141
EX / IN
Pitch
14
14
19
11
19
11
TPI
16
16
16
16
16
16
L mm
Dimensions
1.0 1.2
1.0 1.2
0.8 0.9
1.1 1.5
0.8 0.9
1.1 1.5
9.525
9.525
9.525
9.525
9.525
9.525
I.C. A B
LT10
LT10
LT10
LT10
LT10
LT10
Grade
BSW, BSF, BSP B.S.84: 1956ISO 228-1: 1994
BSPT NUT
BSPTSCREW
27.5°
90°1°47'
27.5°R 0.137P
R 0.137P
200
THREAD TURNING
HERHolder type
16Insert sizeTool length V-Vertical
L I.C.06
08
11
16
22
27
4.00
5.00
6.35
9.525
12.70
15.875
2020
External ToolholdersSquare Shank
Internal Toolholdersround shank
Shank
8101216
2520
32
H - 100
K - 125
L - 140
M - 150
R - 200
P - 170
S - 250
T - 30010121620
3225
40
HERExternal right handed
HELExternal left handed
HIRInternal right handed
HILInternal left handed
K
Tool Holder Ordering Code
201
THREAD TURNING
HER 1616 H16 TH200001ER16 16 10016 16
HER 2020 K16 TH200004ER16 20 12520 20
HER 2525 M16 TH200007ER16 25 15025 25
Designation Catalog Nr.Insert Type f lh b
External Tool Holders ER16
The holders are made for 1.5 helix angle. In case higher helix is required, it should be replaced by other shim.
h
bf
L
Accessories: On request
Accessories: On request
HIR 0010 H11 TH200010IR11 10 10 12.5 100 7.3-
HIR 0010 K11 TH200013IR11 16 10 12.5 125 25 7.3
Internal Tool Holders IR11
Internal Tool Holders IR16
Designation Catalog Nr.D D1 Dmin L L1 FInsert Type
HIR 0013 M16 TH200016IR16 16 13 16.5 150 32 10.4
HIR 0016 P16 TH200019IR16 20 16 19.5 170 40 11.6
HIR 0020 P16 TH200022IR16 20 20 23.5 170 - 13.6
HIR 0025 R16 TH200025IR16 25 25 28.5 200 - 16.3
Designation Catalog Nr.D D1 Dmin L L1 FInsert Type
Accessories: On request
L
D1
L1
FD
Dmin
The holders are made for 1.5 helix angle. In case higher helix is required, it should be replaced by other shim.
202
THREAD TURNINGMachining conditions
min max
1 125 HB 80 130
2 190 HB 70 110
3 250 HB 60 100
6 180 HB 70 110
4,6 230 HB 70 110
5,7 280 HB 60 100
8 350 HB 50 80
10 220 HB 70 110
10 280 HB 60 100
11 320 HB 50 80
11 350 HB 50 70
14 180 HB 70 110
14 240 HB 60 90
14 290 HB 60 80
14 310 HB 60 80
12 200 HB 70 90
13 42 HRc 60 80
15 150 HB 60 110
15 200 HB 70 110
16 250 HB 60 90
17,19 150 HB 60 110
17,19 200 HB 60 90
18,20 250 HB 60 90
31,32 Incoloy 800 240 HB 40 60
33 Inconel 700 250 HB 30 50
34 Stellite 21 350 HB 20 40
36 TiAl6V4 - 40 70
37 T40 - 25 50
38 45 HRc 30 50
38 50 HRc 25 50
38 55 HRc 25 40
Chilled Cast Iron 40 Ni-Hard 2 400 HB 25 40
White Cast Iron 41 G-X300CrMo15 55 HRc 25 40
NF Al (>8%Si) 12 25 AlSi12 130 HB 80 300
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3X40CrMoV5,
H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr4211
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Passes
min max
Pitch
mm TPI
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Vc [m/min]
min max
Unlegiert
Stah
l Niedriglegiert
Hochlegiert
Edel
stah
l
Austenitisch
Duplex
Ferritisch &Martensitisch
Guss
eise
n Grau
Sphäroguss
Supe
rleg.
Fe, Ni & Co-Basiert
Ti-Basiert
Gehä
rtete
s M
at.
Stahl
Schalenhartguss
Weißes Guss.
NE Al (>8%Si)
MILLING
203
Cutters
MILLING LT 30 | LT 3000
ADKT
204
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
A D K T
Shape Clearance Angle Toleranced ± 0.05m ± 0.013s ± 0.025
85° 15°
Fixing,Chipbreaker
sl
Ø dm
Helical Interpolation SurfacingSlottingShoulder Mill
M00015730.96 Right5.6315.75ADKT 1505 PDTR LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
M00022090.96 Right5.6315.75ADKT 1505 PDTR LT 3000
Insert Designation Catalog Nr.Directions rl
LT 3000 Multi-MatTM General Usage – Premium
Pocket MillingPlungingRamping Down
MILLING
205
Cutters
End Mill for ADKT 1505 PDTR
Shell Mill for ADKT 1505 PDTR
Cutter Designation Catalog Nr.D zd L1 L Ap
LT 790 W-W-D025/2* M200161325 225 44 100 15 5
LT 790 W-W-D032/3* M200150332 332 50 110 15 3
LT 790 W-W-D040/4* M200161440 432 45 115 15 2.5
α Ramp°
Cutter Designation
LT 790 M-W-D040/4*
LT 790 M-W-D080/7*
LT 790 M-W-D100/8*
LT 790 M-W-D125/9*
LT 790 M-W-D050/5*
LT 790 M-W-D063/6*
Catalog Nr.
M2001615
M2001617
M2001618
M2001619
M2001504
M2001616
D
40
80
100
125
50
63
z
4
7
8
9
5
6
Ap
15
15
15
15
15
15
d
16
27
32
40
22
22
L
40
50
50
63
40
40
α Ramp°
1.4
1.1
0.8
2.5
2.2
1.8
* On request
* On request
Dd
Ap
LL1
90°
D
d
Ap
L
90°
ADKT
Screw:Key:
M2000597M2000602
Screw:
Key:
M2000597
M2000602
MILLING
206
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 14.0 0.18 0.32 190 330 44.0 0.23 2250
2 190 HB 0.5 14.0 0.18 0.32 190 300 44.0 0.23 2220
3 250 HB 0.5 14.0 0.18 0.32 190 250 44.0 0.23 2200
6 180 HB 0.5 14.0 0.15 0.25 150 240 44.0 0.20 2200
4,6 230 HB 0.5 14.0 0.15 0.25 150 210 44.0 0.20 1180
5,7 280 HB 0.5 14.0 0.15 0.22 130 190 44.0 0.18 1150
8 350 HB 0.5 14.0 0.15 0.22 130 170 44.0 0.18 1140
10 220 HB 0.5 10.0 0.12 0.22 90 150 33.0 0.18 1130
10 280 HB 0.5 10.0 0.12 0.22 90 130 33.0 0.18 1120
11 320 HB 0.5 10.0 0.12 0.18 60 110 33.0 0.16 1100
11 350 HB 0.5 10.0 0.12 0.18 60 90 33.0 0.16 880
14 180 HB 0.5 14.0 0.15 0.25 190 250 44.0 0.20 2220
14 240 HB 0.5 14.0 0.12 0.22 160 210 44.0 0.20 1190
14 290 HB 0.5 10.0 0.12 0.18 70 130 33.0 0.16 1100
14 310 HB 0.5 10.0 0.12 0.18 70 120 33.0 0.16 990
12 200 HB 0.5 14.0 0.15 0.25 150 210 44.0 0.20 1190
13 42 HRc 0.5 10.0 0.15 0.20 90 150 33.0 0.16 1130
15 150 HB 0.5 14.0 0.18 0.32 150 240 44.0 0.23 2200
15 200 HB 0.5 14.0 0.18 0.32 150 220 44.0 0.23 1180
16 250 HB 0.5 14.0 0.18 0.32 150 190 44.0 0.23 1160
17,19 150 HB 0.5 14.0 0.15 0.28 100 200 44.0 0.20 1180
17,19 200 HB 0.5 14.0 0.15 0.28 100 180 44.0 0.20 1150
18,20 250 HB 0.5 14.0 0.15 0.28 100 150 44.0 0.20 1130
31,32 Incoloy 800 240 HB 0.5 10.0 0.12 0.18 25 45 33.0 0.16 332
33 Inconel 700 250 HB 0.5 10.0 0.12 0.18 25 45 33.0 0.16 330
34 Stellite 21 350 HB 0.5 10.0 0.12 0.18 25 45 33.0 0.16 330
36 TiAl6V4 - 0.5 10.0 0.12 0.20 40 65 33.0 0.18 555
37 T40 - 0.5 10.0 0.12 0.18 30 55 33.0 0.16 440
38 45 HRc 0.5 5.0 0.10 0.18 40 80 22.0 0.14 660
38 50 HRc 0.5 3.0 0.10 0.16 40 70 11.5 0.13 555
38 55 HRc 0.5 1.5 0.10 0.14 40 60 11.0 0.12 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 4.0 0.10 0.18 40 80 11.5 0.14 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.14 30 60 11.0 0.12 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 14.0 0.18 0.32 200 400 4.0 0.25 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
ADKT 1505 – LT 30 | LT 3000
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
207
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
A O M T
Shape Clearance Angle Toleranced ± 0.05m ± 0.08s ± 0.13
= Special
°
Fixing, Chipbreaker
sl
Ø dm
Helical Interpolation SurfacingSlottingShoulder Milling
M00016400.70 Right3.6211.93AOMT 123608 PETR LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
LT 3000 Multi-MatTM General Usage – Premium
AOMT
M00016400.70 Right3.6211.93AOMT 123608 PETR LT 30
Pocket MillingPlungingRamping Down
AOMT 123608 PETR LT 3000 M00022100.70 Right3.6211.93
Designation Catalog Nr.Directions rl
MILLING
208
Cutters
End Mill for AOMT 123608 PETR
Shell Mill for AOMT 123608 PETR
Cutter Designation Catalog Nr.D zd L1 L Ap
LT 720 W-W-D016/2* M200178116 216 22 85 10 12
LT 720 W-W-D020/3*
LT 720 W-W-D020/2*
LT 720 W-W-D025/4*
M2001782
M2001818
M2001819
20
20
25
3
2
4
20
20
25
25
25
25
90
90
95
10
10
10
7
7
5
LT 720 W-W-D025/3*
LT 720 W-W-D032/4*
LT 720 W-W-D032/5*
M2001783
M2001784
M2001784
25
32
32
3
4
5
25
32
32
25
25
25
95
95
95
10
10
10
5
3
3
α Ramp°
Cutter Designation
LT 720 M-W-D040/6*
LT 720 M-W-D050/7*
Catalog Nr.
M2001785
M2001821
D
40
50
z
6
7
Ap
10
10
d
22
22
L
40
40
α Ramp°
2.5
2.2
D
d
Ap
L
90°
* On request
* On request
Dd
Ap
LL1
90°
M2002181
M2000601
Screw:
Key:
M2002181
M2000601
Screw:
Key:
MILLING
209
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 11.0 0.13 0.22 190 330 22.0 0.15 2250
2 190 HB 0.5 11.0 0.13 0.22 190 300 22.0 0.15 2220
3 250 HB 0.5 11.0 0.13 0.22 190 250 22.0 0.15 2200
6 180 HB 0.5 11.0 0.11 0.18 150 240 22.0 0.13 2200
4,6 230 HB 0.5 11.0 0.11 0.18 150 210 22.0 0.13 1180
5,7 280 HB 0.5 11.0 0.11 0.15 130 190 22.0 0.12 1150
8 350 HB 0.5 11.0 0.11 0.15 130 170 22.0 0.12 1140
10 220 HB 0.5 7.9 0.08 0.15 90 150 11.5 0.12 1130
10 280 HB 0.5 7.9 0.08 0.15 90 130 11.5 0.12 1120
11 320 HB 0.5 7.9 0.08 0.13 60 110 11.5 0.10 1100
11 350 HB 0.5 7.9 0.08 0.13 60 90 11.5 0.10 880
14 180 HB 0.5 11.0 0.11 0.18 190 250 22.0 0.13 2220
14 240 HB 0.5 11.0 0.08 0.15 160 210 22.0 0.13 1190
14 290 HB 0.5 7.9 0.08 0.13 70 130 11.5 0.10 1100
14 310 HB 0.5 7.9 0.08 0.13 70 120 11.5 0.10 990
12 200 HB 0.5 11.0 0.11 0.18 150 210 22.0 0.13 1190
13 42 HRc 0.5 7.9 0.08 0.14 90 150 11.5 0.10 1130
15 150 HB 0.5 11.0 0.13 0.22 150 240 22.0 0.15 2200
15 200 HB 0.5 11.0 0.13 0.22 150 220 22.0 0.15 1180
16 250 HB 0.5 11.0 0.13 0.22 150 190 22.0 0.15 1160
17,19 150 HB 0.5 11.0 0.11 0.20 100 200 22.0 0.13 1180
17,19 200 HB 0.5 11.0 0.11 0.20 100 180 22.0 0.13 1150
18,20 250 HB 0.5 11.0 0.11 0.20 100 150 22.0 0.13 1130
31,32 Incoloy 800 240 HB 0.5 7.9 0.08 0.13 25 45 11.5 0.10 332
33 Inconel 700 250 HB 0.5 7.9 0.08 0.13 25 45 11.5 0.10 330
34 Stellite 21 350 HB 0.5 7.9 0.08 0.13 25 45 11.5 0.10 330
36 TiAl6V4 - 0.5 7.9 0.08 0.14 40 65 11.5 0.12 555
37 T40 - 0.5 7.9 0.08 0.13 30 55 11.5 0.10 440
38 45 HRc 0.5 3.9 0.07 0.13 40 80 11.0 0.09 660
38 50 HRc 0.5 2.4 0.07 0.11 40 70 00.8 0.08 555
38 55 HRc 0.5 1.2 0.07 0.10 40 60 00.5 0.08 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 3.1 0.07 0.13 40 80 00.8 0.09 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.2 0.07 0.10 30 60 00.5 0.08 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 11.0 0.13 0.22 200 400 2.0 0.16 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
AOMT 123608 PETR – LT 30 | LT 3000
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
210
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
A P K T11°
Shape Clearance Angle Toleranced ± 0.05m ± 0.013s ± 0.025
Fixing,Chipbreaker
sl
Ø dm
Pocket MillingPlungingHelical Interpolation
Ramping Down
Surfacing
SlottingShoulder Milling
M00000210.95 Right4.7615.30APKT 1604 PDTR LT 30
M00000220.80 Right4.7615.30APKT 1604 PDTR LT 30 (NEW)
M00029234.00 Right3.5310.39APKT 100340 PDTR LT 30
M00029223.20 Right3.5310.39APKT 100332 PDTR LT 30
M00030941.60 Right3.5310.39APKT 100316 PDTR LT 30
M00029211.20 Right3.5310.39APKT 100312 PDTR LT 30
M00029180.80 Right3.5310.39APKT 1003 PDTR LT 30 (NEW)
M00029200.40 Right3.5310.39APKT 100304 PDTR LT 30
M00038850.40 Right2.166.00APKT 060204 PDTR LT 30
3.20 Right4.7615.30APKT 160432 PDTR LT 30
M00018100.80 Right5.1217.48APKT 1705 PETR LT 30
M0003833
M0001569
2.40 Right4.7615.30APKT 160424 PDTR LT 30
M00001721.60 Right4.7615.30APKT 160416 PDTR LT 30
LT 30 Multi-MatTM General Usage – Standard
sInsert Designation Catalog Nr.Directionrl
211
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
M00040271.60 Right4.7615.30APKT 160416 PDTR LT 3000
M00021820.80 Right4.7615.30APKT 1604 PDTR LT 3000 (NEW)
M00033943.20 Right3.5310.39APKT 100332 PDTR LT 3000
M00033954.00 Right3.5310.39APKT 100340 PDTR LT 3000
M00033921.60 Right3.5310.39APKT 100316 PDTR LT 3000
M00033911.20 Right3.5310.39APKT 100312 PDTR LT 3000
M00033880.80 Right3.5310.39APKT 1003 PDTR LT 3000 (NEW)
M00033890.40 Right3.5310.39APKT 100304 PDTR LT 3000
M00040260.40 Right2.166.00APKT 060204 PDTR LT 3000
M00040303.20 Right4.7615.30APKT 160432 PDTR LT 3000
M00022120.80 Right5.1217.48APKT 1705 PETR LT 3000
M00040292.40 Right4.7615.30APKT 160424 PDTR LT 3000
Insert Designation Catalog Nr.Directions rl
LT 3000 Multi-MatTM General Usage – Premium
Pocket-MillingPlungingHelical Interpolation
Ramping Down
Surfacing
SlottingShoulder Milling
A P K T APKT
MILLING
212
Cutters
End Mill for APKT 060204**
Cutter Designation Catalog Nr.D zd L1 L Ap
LT 751 C-W-D012/3 M200306912 312 26 80 5.2 5
LT 751 CL-W-D016/3 M200307016 316 50 120 5.2 2.4
LT 751 C-W-D016/4 M200307116 416 32 90 5.2 2.4
LT 751 C-W-D012/3 M200306912 312 26 80 5.2 5
LT 751 C-W-D010/2 M200306610 210 16 72 5.2 7
LT 751 C-W-D020/5
LT 751 C-W-D032/8*
M2003072
M2003074
20
32
5
8
20
25
40
40
100
130
5.2
5.2
1.6
0.8
LT 751 C-W-D025/7*
LT 751 C-W-D040/10*
M2003073
M2003075
25
40
7
10
20
32
40
40
120
140
5.2
5.2
1.2
0.6
α Ramp°
* On request
Handle:
TORX+:
Adapter 0.4 Nm:
End Mill for APKT 100332/40 PDTR
* On request M2002181M2000601
Screw:Key:
Cutter Designation Catalog Nr.D zd L1 L Ap
LT 745 W-W-D020/3* M200158920 320 30 100 9 7
LT 745 WL-W-D016/2* M200184916 216 35 150 9 10
LT 745 WL-W-D025/4* M200185125 425 40 200 9 5
LT 745 W-W-D016/2* M200158716 216 25 100 9 10
LT 745 W-W-D025/3* M200159125 325 30 120 9 5
LT 745 W-W-D020/3* M200158920 320 30 100 9 7
LT 745 WL-W-D020/3* M200185020 320 35 150 9 7
LT 745 WL-W-D032/4* M200185232 432 40 200 9 3
LT 745 W-W-D032/5* M200184832 532 30 120 9 3
α Ramp°
Shell Mill for APKT 100332/40 PDTR
Screw:Key:
M2002181M2000601
Cutter Designation
LT 745 M-W-D040/6*
LT 745 M-W-D050/7*
Catalog Nr.
M2001580
M2001581
D
40
50
z
6
7
d
22
22
L
40
40
Ap
9
9
* On request
** Preset 0.4 Nm screwdriver included. M2002922
M2003064
M2002923
M2001640Screw:Replacement parts:
MILLING
213
Cutters
LT 741 C-W-D020/3 M200280820 320 25 100 9 7
End Mill for APKT 1003 PDTR
Cutter Designation Catalog Nr.D zd L1 L Ap
LT 741 CL-W-D012/1* M200281612 116 32 150 9 5
LT 741 C-W-D010/1* M200280210 110 24 80 9 5
LT 741 C-W-D014/1* M200280414 116 24 80 9 5
LT 741 CL-W-D010/1* M200281510 116 32 150 9 5
LT 741 C-W-D016/2 M200280616 216 25 100 9 12
LT 741 C-W-D012/1* M200280312 112 24 80 9 5
LT 741 CL-W-D016/2 M200281716 216 35 150 9 12
LT 741 WL-W-D032/4 M200282032 432 40 200 9
LT 741 C-W-D018/2 M200280718 220 30 85 9 12
LT 741 CL-W-D020/3 M200281820 320 40 150 9 7
LT 741 C-W-D022/3 M200280922 320 35 95 9 7
LT 741 C-W-D025/3 M200281025 325 32 120 9 5
LT 741 C-W-D025/4 M200281125 425 32 120 9 5
LT 741 CL-W-D025/4 M200281925 425 40 200 9 5
LT 741 C-W-D028/4 M200281228 425 32 120 9 2
LT 741 C-W-D030/4 M200281330 425 32 95 9 2
LT 741 W-W-D032/5 M200281432 532 32 95 9 3
3
α Ramp°
Dd
Ap
LL1
90°
Dd
Ap
LL1
90°
* On request
C W
M2002181M2000601
Screw:Key:
MILLING
214
Cutters
Screw Coupling for APKT 1003 PDTR
Cutter Designation Catalog Nr.D zd L1 Ap
LT 741 S-W-D016/2 M200296216 2M8 25 9 12
LT 741 S-W-D020/3 M200296320 3M10 30 9 7
LT 741 S-W-D025/4 M200296425 4M12 35 9 5
α Ramp°
Screw:Key:
M2002181M2000601
Dd
Ap
L1
90°
Shell Mill for APKT 1003 PDTR
Screw:Key:
M2002181M2000601
Cutter Designation
LT 741 M-W-D040/6
LT 741 M-W-D080/11*
LT 741 M-W-D050/7
LT 741 M-W-D063/8
Catalog Nr.
M2002798
M2002801
M2002799
M2002800
D
40
80
50
63
z
6
10
7
8
d
16
27
22
22
L
40
50
40
40
Ap
9
9
9
9
α Ramp°
1.4
2.5
2.2
1.8
D
d
Ap
L
90°
* On request
MILLING
215
Cutters
Dd
Ap
LL1
90°
Shell Mill for APKT 1604 PDTR
Screw:Key:
M2000597M2000602
Screw:Key:
M2000597M2000602
Cutter Designation
LT 731 M-W-D040/4
LT 731 M-W-D080/7
LT 731 M-W-D125/9
LT 731 M-W-D100/8
LT 731 M-D-D160/10*
LT 731 M-W-D050/5
LT 731 M-W-D063/6
Catalog Nr.
M2002971
M2002974
M2002976
M2002975
M2002977
M2002972
M2002973
D
40
80
125
100
160
50
63
z
4
7
9
8
10
5
6
Ap
15
15
15
15
15
15
15
d
16
27
40
32
40
22
22
L
40
50
63
50
63
40
40
α Ramp°
1.4
0.8
1.4
n / a**
2.5
2.2
1.8
D
d
Ap
L
90°
End Mill for APKT 1604 PDTR
Cutter Designation Catalog Nr.D zd L1 L Ap
LT 731 W-W-D032/3 M200296832 332 50 110 15 3
LT 731 WL-W-D025/2 M200296525 225 90 220 15 5
LT 731 WL-W-D040/4 M200296940 432 90 220 15 2.5
LT 731 W-W-D025/2 M200296625 225 44 100 15 5
LT 731 W-W-D040/4 M200297040 432 50 115 15 2.5
LT 731 WL-W-D032/3 M200296732 332 90 220 15 3
α Ramp°
* On request** Not available
MILLING
216
Cutters
Shell Mill for APKT 1705 PETR
Screw:Key:
M2000597M2000602
Screw:Key:
M2000597M2000602
Cutter Designation
LT 737 M-W-D040/4
LT 737 M-W-D080/7
LT 737 M-W-D125/9
LT 737 M-W-D100/7
LT 737 M-W-D160/10
LT 737 M-W-D050/5
LT 737 M-W-D063/6
Catalog Nr.
M2001838
M2001842
M2001844
M2001843
M2001845
M2001839
M2001841
D D1
40 40
80 80
125 125
100 100
160 160
50 50
63 63
z
4
7
9
7
10
5
6
Ap
16
16
16
16
16
16
16
d
16
27
40
32
40
22
22
L
40
50
63
50
63
40
40
α Ramp°
1.4
0.8
1.4
-
2.5
2.2
1.8
D
d
Ap
L
90°
End Mill for APKT 1705 PETR
Cutter Designation Catalog Nr.D zD1 d L1 L Ap
LT 737 WL-W-D032/3 M200183732 332 32 65 200 16 3
LT 737 W-W-D025/2 M200183325 225 20 32 100 16 5
LT 737 W-W-D040/4 M200183540 440 32 45 115 16 2.5
LT 737 WL-W-D025/2 M200183625 225 25 40 210 16 5
LT 737 WL-W-D040/4 M200198240 440 32 45 200 16 2.5LT 737 WL-W-D040/4 M200198240 440 32 45 200 16 2.5
LT 737 W-W-D032/3 M200183432 332 32 40 110 16 3
α Ramp°
Dd
Ap
LL1
90°
MILLING
217
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.3 5.5 0.04 0.13 190 330 11.3 0.07 2250
2 190 HB 0.3 5.5 0.04 0.13 190 300 11.3 0.07 2220
3 250 HB 0.3 5.5 0.04 0.13 190 250 11.3 0.07 2200
6 180 HB 0.3 5.5 0.03 0.10 150 240 11.3 0.06 2200
4,6 230 HB 0.3 5.5 0.03 0.10 150 210 11.3 0.06 1180
5,7 280 HB 0.3 5.5 0.03 0.09 130 190 11.3 0.05 1150
8 350 HB 0.3 5.5 0.03 0.09 130 170 11.3 0.05 1140
10 220 HB 0.3 3.9 0.03 0.09 90 150 11.0 0.05 1130
10 280 HB 0.3 3.9 0.03 0.09 90 130 11.0 0.05 1120
11 320 HB 0.3 3.9 0.03 0.07 60 110 11.0 0.05 1100
11 350 HB 0.3 3.9 0.03 0.07 60 90 11.0 0.05 880
14 180 HB 0.3 5.5 0.03 0.10 190 250 11.3 0.06 2220
14 240 HB 0.3 5.5 0.03 0.09 160 210 11.3 0.06 1190
14 290 HB 0.3 3.9 0.03 0.07 70 130 11.0 0.05 1100
14 310 HB 0.3 3.9 0.03 0.07 70 120 11.0 0.05 990
12 200 HB 0.3 5.5 0.03 0.10 150 210 11.3 0.06 1190
13 42 HRc 0.3 3.9 0.03 0.08 90 150 11.0 0.05 1130
15 150 HB 0.3 5.5 0.04 0.13 150 240 11.3 0.07 2200
15 200 HB 0.3 5.5 0.04 0.13 150 220 11.3 0.07 1180
16 250 HB 0.3 5.5 0.04 0.13 150 190 11.3 0.07 1160
17,19 150 HB 0.3 5.5 0.03 0.11 100 200 11.3 0.06 1180
17,19 200 HB 0.3 5.5 0.03 0.11 100 180 11.3 0.06 1150
18,20 250 HB 0.3 5.5 0.03 0.11 100 150 11.3 0.06 1130
31,32 Incoloy 800 240 HB 0.3 3.9 0.03 0.07 25 45 11.0 0.05 332
33 Inconel 700 250 HB 0.3 3.9 0.03 0.07 25 45 11.0 0.05 330
34 Stellite 21 350 HB 0.3 3.9 0.03 0.07 25 45 11.0 0.05 330
36 TiAl6V4 - 0.3 3.9 0.03 0.08 40 65 11.0 0.05 555
37 T40 - 0.3 3.9 0.03 0.07 30 55 11.0 0.05 440
38 45 HRc 0.3 2.0 0.02 0.07 40 80 00.7 0.04 660
38 50 HRc 0.3 1.2 0.02 0.06 40 70 00.5 0.04 555
38 55 HRc 0.3 0.6 0.02 0.06 40 60 00.3 0.04 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.6 0.02 0.07 40 80 00.5 0.04 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 0.6 0.02 0.06 30 60 00.3 0.04 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 5.5 0.04 0.13 200 400 11.3 0.08 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
APKT 060204 PDTR – LT 30 | LT3000
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
218
Machining Conditions
APKT 1003 PDTR – LT 30 | LT3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 9.0 0.13 0.26 190 330 22.0 0.17 2250
2 190 HB 0.5 9.0 0.13 0.26 190 300 22.0 0.17 2220
3 250 HB 0.5 9.0 0.13 0.26 190 250 22.0 0.17 2200
6 180 HB 0.5 9.0 0.11 0.21 150 240 22.0 0.15 2200
4,6 230 HB 0.5 9.0 0.11 0.21 150 210 22.0 0.15 1180
5,7 280 HB 0.5 9.0 0.11 0.18 130 190 22.0 0.13 1150
8 350 HB 0.5 9.0 0.11 0.18 130 170 22.0 0.13 1140
10 220 HB 0.5 6.4 0.08 0.18 90 150 11.5 0.13 1130
10 280 HB 0.5 6.4 0.08 0.18 90 130 11.5 0.13 1120
11 320 HB 0.5 6.4 0.08 0.15 60 110 11.5 0.12 1100
11 350 HB 0.5 6.4 0.08 0.15 60 90 11.5 0.12 880
14 180 HB 0.5 9.0 0.11 0.21 190 250 22.0 0.15 2220
14 240 HB 0.5 9.0 0.08 0.18 160 210 22.0 0.15 1190
14 290 HB 0.5 6.4 0.08 0.15 70 130 11.5 0.12 1100
14 310 HB 0.5 6.4 0.08 0.15 70 120 11.5 0.12 990
12 200 HB 0.5 9.0 0.11 0.21 150 210 22.0 0.15 1190
13 42 HRc 0.5 6.4 0.11 0.16 90 150 11.5 0.12 1130
15 150 HB 0.5 9.0 0.13 0.26 150 240 22.0 0.17 2200
15 200 HB 0.5 9.0 0.13 0.26 150 220 22.0 0.17 1180
16 250 HB 0.5 9.0 0.13 0.26 150 190 22.0 0.17 1160
17,19 150 HB 0.5 9.0 0.11 0.23 100 200 22.0 0.15 1180
17,19 200 HB 0.5 9.0 0.11 0.23 100 180 22.0 0.15 1150
18,20 250 HB 0.5 9.0 0.11 0.23 100 150 22.0 0.15 1130
31,32 Incoloy 800 240 HB 0.5 6.4 0.08 0.15 25 45 11.5 0.12 332
33 Inconel 700 250 HB 0.5 6.4 0.08 0.15 25 45 11.5 0.12 330
34 Stellite 21 350 HB 0.5 6.4 0.08 0.15 25 45 11.5 0.12 330
36 TiAl6V4 - 0.5 6.4 0.08 0.16 40 65 11.5 0.13 555
37 T40 - 0.5 6.4 0.08 0.15 30 55 11.5 0.12 440
38 45 HRc 0.5 3.2 0.07 0.15 40 80 11.0 0.10 660
38 50 HRc 0.5 1.9 0.07 0.13 40 70 00.8 0.09 555
38 55 HRc 0.5 1.0 0.07 0.11 40 60 00.5 0.09 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.6 0.07 0.15 40 80 00.8 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.0 0.07 0.11 30 60 00.5 0.09 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.13 0.26 200 400 22.0 0.18 280
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5X2CrNiN23-4,
S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
219
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 9.0 0.11 0.20 190 330 22.0 0.14 2250
2 190 HB 0.5 9.0 0.11 0.20 190 300 22.0 0.14 2220
3 250 HB 0.5 9.0 0.11 0.20 190 250 22.0 0.14 2200
6 180 HB 0.5 9.0 0.09 0.16 150 240 22.0 0.12 2200
4,6 230 HB 0.5 9.0 0.09 0.16 150 210 22.0 0.12 1180
5,7 280 HB 0.5 9.0 0.09 0.14 130 190 22.0 0.11 1150
8 350 HB 0.5 9.0 0.09 0.14 130 170 22.0 0.11 1140
10 220 HB 0.5 6.4 0.07 0.14 90 150 11.5 0.11 1130
10 280 HB 0.5 6.4 0.07 0.14 90 130 11.5 0.11 1120
11 320 HB 0.5 6.4 0.07 0.11 60 110 11.5 0.10 1100
11 350 HB 0.5 6.4 0.07 0.11 60 90 11.5 0.10 880
14 180 HB 0.5 9.0 0.09 0.16 190 250 22.0 0.12 2220
14 240 HB 0.5 9.0 0.07 0.14 160 210 22.0 0.12 1190
14 290 HB 0.5 6.4 0.07 0.11 70 130 11.5 0.10 1100
14 310 HB 0.5 6.4 0.07 0.11 70 120 11.5 0.10 990
12 200 HB 0.5 9.0 0.09 0.16 150 210 22.0 0.12 1190
13 42 HRc 0.5 6.4 0.09 0.12 90 150 11.5 0.10 1130
15 150 HB 0.5 9.0 0.11 0.20 150 240 22.0 0.14 2200
15 200 HB 0.5 9.0 0.11 0.20 150 220 22.0 0.14 1180
16 250 HB 0.5 9.0 0.11 0.20 150 190 22.0 0.14 1160
17,19 150 HB 0.5 9.0 0.09 0.17 100 200 22.0 0.12 1180
17,19 200 HB 0.5 9.0 0.09 0.17 100 180 22.0 0.12 1150
18,20 250 HB 0.5 9.0 0.09 0.17 100 150 22.0 0.12 1130
31,32 Incoloy 800 240 HB 0.5 6.4 0.07 0.11 25 45 11.5 0.10 332
33 Inconel 700 250 HB 0.5 6.4 0.07 0.11 25 45 11.5 0.10 330
34 Stellite 21 350 HB 0.5 6.4 0.07 0.11 25 45 11.5 0.10 330
36 TiAl6V4 - 0.5 6.4 0.07 0.12 40 65 11.5 0.11 555
37 T40 - 0.5 6.4 0.07 0.11 30 55 11.5 0.10 440
38 45 HRc 0.5 3.2 0.06 0.11 40 80 11.0 0.09 660
38 50 HRc 0.5 1.9 0.06 0.10 40 70 00.8 0.08 555
38 55 HRc 0.5 1.0 0.06 0.09 40 60 00.5 0.07 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.6 0.06 0.11 40 80 00.8 0.09 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.0 0.06 0.09 30 60 00.5 0.07 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.11 0.20 200 400 22.0 0.16 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
APKT 100304 PDTR – LT 30 | LT3000
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
220
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 9.0 0.13 0.28 190 330 22.0 0.20 2250
2 190 HB 0.5 9.0 0.13 0.28 190 300 22.0 0.20 2220
3 250 HB 0.5 9.0 0.13 0.28 190 250 22.0 0.20 2200
6 180 HB 0.5 9.0 0.11 0.22 150 240 22.0 0.18 2200
4,6 230 HB 0.5 9.0 0.11 0.22 150 210 22.0 0.18 1180
5,7 280 HB 0.5 9.0 0.11 0.19 130 190 22.0 0.16 1150
8 350 HB 0.5 9.0 0.11 0.19 130 170 22.0 0.16 1140
10 220 HB 0.5 6.4 0.08 0.19 90 150 11.5 0.16 1130
10 280 HB 0.5 6.4 0.08 0.19 90 130 11.5 0.16 1120
11 320 HB 0.5 6.4 0.08 0.16 60 110 11.5 0.14 1100
11 350 HB 0.5 6.4 0.08 0.16 60 90 11.5 0.14 880
14 180 HB 0.5 9.0 0.11 0.22 190 250 22.0 0.18 2220
14 240 HB 0.5 9.0 0.08 0.19 160 210 22.0 0.18 1190
14 290 HB 0.5 6.4 0.08 0.16 70 130 11.5 0.14 1100
14 310 HB 0.5 6.4 0.08 0.16 70 120 11.5 0.14 990
12 200 HB 0.5 9.0 0.11 0.22 150 210 22.0 0.18 1190
13 42 HRc 0.5 6.4 0.11 0.18 90 150 11.5 0.14 1130
15 150 HB 0.5 9.0 0.13 0.28 150 240 22.0 0.20 2200
15 200 HB 0.5 9.0 0.13 0.28 150 220 22.0 0.20 1180
16 250 HB 0.5 9.0 0.13 0.28 150 190 22.0 0.20 1160
17,19 150 HB 0.5 9.0 0.11 0.25 100 200 22.0 0.18 1180
17,19 200 HB 0.5 9.0 0.11 0.25 100 180 22.0 0.18 1150
18,20 250 HB 0.5 9.0 0.11 0.25 100 150 22.0 0.18 1130
31,32 Incoloy 800 240 HB 0.5 6.4 0.08 0.16 25 45 11.5 0.14 332
33 Inconel 700 250 HB 0.5 6.4 0.08 0.16 25 45 11.5 0.14 330
34 Stellite 21 350 HB 0.5 6.4 0.08 0.16 25 45 11.5 0.14 330
36 TiAl6V4 - 0.5 6.4 0.08 0.18 40 65 11.5 0.16 555
37 T40 - 0.5 6.4 0.08 0.16 30 55 11.5 0.14 440
38 45 HRc 0.5 3.2 0.07 0.16 40 80 11.0 0.12 660
38 50 HRc 0.5 1.9 0.07 0.14 40 70 00.8 0.11 555
38 55 HRc 0.5 1.0 0.07 0.12 40 60 00.5 0.11 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.6 0.07 0.16 40 80 00.8 0.12 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.0 0.07 0.12 30 60 00.5 0.11 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.13 0.28 200 400 22.0 0.22 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
APKT 100312 PDTR – LT 30 | LT 3000
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
221
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 9.0 0.13 0.28 190 330 22.0 0.20 2250
2 190 HB 0.5 9.0 0.13 0.28 190 300 22.0 0.20 2220
3 250 HB 0.5 9.0 0.13 0.28 190 250 22.0 0.20 2200
6 180 HB 0.5 9.0 0.11 0.22 150 240 22.0 0.18 2200
4,6 230 HB 0.5 9.0 0.11 0.22 150 210 22.0 0.18 1180
5,7 280 HB 0.5 9.0 0.11 0.19 130 190 22.0 0.16 1150
8 350 HB 0.5 9.0 0.11 0.19 130 170 22.0 0.16 1140
10 220 HB 0.5 6.4 0.08 0.19 90 150 11.5 0.16 1130
10 280 HB 0.5 6.4 0.08 0.19 90 130 11.5 0.16 1120
11 320 HB 0.5 6.4 0.08 0.16 60 110 11.5 0.14 1100
11 350 HB 0.5 6.4 0.08 0.16 60 90 11.5 0.14 880
14 180 HB 0.5 9.0 0.11 0.22 190 250 22.0 0.18 2220
14 240 HB 0.5 9.0 0.08 0.19 160 210 22.0 0.18 1190
14 290 HB 0.5 6.4 0.08 0.16 70 130 11.5 0.14 1100
14 310 HB 0.5 6.4 0.08 0.16 70 120 11.5 0.14 990
12 200 HB 0.5 9.0 0.11 0.22 150 210 22.0 0.18 1190
13 42 HRc 0.5 6.4 0.11 0.18 90 150 11.5 0.14 1130
15 150 HB 0.5 9.0 0.13 0.28 150 240 22.0 0.20 2200
15 200 HB 0.5 9.0 0.13 0.28 150 220 22.0 0.20 1180
16 250 HB 0.5 9.0 0.13 0.28 150 190 22.0 0.20 1160
17,19 150 HB 0.5 9.0 0.11 0.25 100 200 22.0 0.18 1180
17,19 200 HB 0.5 9.0 0.11 0.25 100 180 22.0 0.18 1150
18,20 250 HB 0.5 9.0 0.11 0.25 100 150 22.0 0.18 1130
31,32 Incoloy 800 240 HB 0.5 6.4 0.08 0.16 25 45 11.5 0.14 332
33 Inconel 700 250 HB 0.5 6.4 0.08 0.16 25 45 11.5 0.14 330
34 Stellite 21 350 HB 0.5 6.4 0.08 0.16 25 45 11.5 0.14 330
36 TiAl6V4 - 0.5 6.4 0.08 0.18 40 65 11.5 0.16 555
37 T40 - 0.5 6.4 0.08 0.16 30 55 11.5 0.14 440
38 45 HRc 0.5 3.2 0.07 0.16 40 80 11.0 0.12 660
38 50 HRc 0.5 1.9 0.07 0.14 40 70 00.8 0.11 555
38 55 HRc 0.5 1.0 0.07 0.12 40 60 00.5 0.11 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.6 0.07 0.16 40 80 00.8 0.12 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.0 0.07 0.12 30 60 00.5 0.11 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.13 0.28 200 400 22.0 0.22 280
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5X2CrNiN23-4,
S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
APKT 100316 PDTR – LT 30 | LT 3000
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
222
Machining Conditions
APKT 100332 PDTR – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 9.0 0.13 0.28 190 330 11.0 0.29 2250
2 190 HB 0.5 9.0 0.13 0.28 190 300 11.0 0.29 2220
3 250 HB 0.5 9.0 0.13 0.28 190 250 11.0 0.29 2200
6 180 HB 0.5 9.0 0.11 0.22 150 240 11.0 0.25 2200
4,6 230 HB 0.5 9.0 0.11 0.22 150 210 11.0 0.25 1180
5,7 280 HB 0.5 9.0 0.11 0.19 130 190 11.0 0.22 1150
8 350 HB 0.5 9.0 0.11 0.19 130 170 11.0 0.22 1140
10 220 HB 0.5 6.4 0.08 0.19 90 150 11.0 0.22 1130
10 280 HB 0.5 6.4 0.08 0.19 90 130 11.0 0.22 1120
11 320 HB 0.5 6.4 0.08 0.16 60 110 11.0 0.20 1100
11 350 HB 0.5 6.4 0.08 0.16 60 90 11.0 0.20 880
14 180 HB 0.5 9.0 0.11 0.22 190 250 11.0 0.25 2220
14 240 HB 0.5 9.0 0.08 0.19 160 210 11.0 0.25 1190
14 290 HB 0.5 6.4 0.08 0.16 70 130 11.0 0.20 1100
14 310 HB 0.5 6.4 0.08 0.16 70 120 11.0 0.20 990
12 200 HB 0.5 9.0 0.11 0.22 150 210 11.0 0.25 1190
13 42 HRc 0.5 6.4 0.11 0.18 90 150 11.0 0.20 1130
15 150 HB 0.5 9.0 0.13 0.28 150 240 11.0 0.29 2200
15 200 HB 0.5 9.0 0.13 0.28 150 220 11.0 0.29 1180
16 250 HB 0.5 9.0 0.13 0.28 150 190 11.0 0.29 1160
17,19 150 HB 0.5 9.0 0.11 0.25 100 200 11.0 0.25 1180
17,19 200 HB 0.5 9.0 0.11 0.25 100 180 11.0 0.25 1150
18,20 250 HB 0.5 9.0 0.11 0.25 100 150 11.0 0.25 1130
31,32 Incoloy 800 240 HB 0.5 6.4 0.08 0.16 25 45 11.0 0.20 332
33 Inconel 700 250 HB 0.5 6.4 0.08 0.16 25 45 11.0 0.20 330
34 Stellite 21 350 HB 0.5 6.4 0.08 0.16 25 45 11.0 0.20 330
36 TiAl6V4 - 0.5 6.4 0.08 0.18 40 65 11.0 0.22 555
37 T40 - 0.5 6.4 0.08 0.16 30 55 11.0 0.20 440
38 45 HRc 0.4 3.2 0.07 0.16 40 80 00.7 0.17 660
38 50 HRc 0.4 1.9 0.07 0.14 40 70 00.7 0.16 555
38 55 HRc 0.4 1.0 0.07 0.12 40 60 00.7 0.15 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.4 2.6 0.07 0.16 40 80 00.7 0.17 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.4 1.0 0.07 0.12 30 60 00.7 0.15 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.13 0.28 200 400 11.0 0.31 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
223
Machining Conditions
APKT 100340 PDTR – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 9.0 0.13 0.46 190 330 11.0 0.35 2250
2 190 HB 0.5 9.0 0.13 0.46 190 300 11.0 0.35 2220
3 250 HB 0.5 9.0 0.13 0.46 190 250 11.0 0.35 2200
6 180 HB 0.5 9.0 0.11 0.36 150 240 11.0 0.30 2200
4,6 230 HB 0.5 9.0 0.11 0.36 150 210 11.0 0.30 1180
5,7 280 HB 0.5 9.0 0.11 0.32 130 190 11.0 0.27 1150
8 350 HB 0.5 9.0 0.11 0.32 130 170 11.0 0.27 1140
10 220 HB 0.5 6.4 0.08 0.32 90 150 11.0 0.27 1130
10 280 HB 0.5 6.4 0.08 0.32 90 130 11.0 0.27 1120
11 320 HB 0.5 6.4 0.08 0.26 60 110 11.0 0.24 1100
11 350 HB 0.5 6.4 0.08 0.26 60 90 11.0 0.24 880
14 180 HB 0.5 9.0 0.11 0.36 190 250 11.0 0.30 2220
14 240 HB 0.5 9.0 0.08 0.32 160 210 11.0 0.30 1190
14 290 HB 0.5 6.4 0.08 0.26 70 130 11.0 0.24 1100
14 310 HB 0.5 6.4 0.08 0.26 70 120 11.0 0.24 990
12 200 HB 0.5 9.0 0.11 0.36 150 210 11.0 0.30 1190
13 42 HRc 0.5 6.4 0.11 0.29 90 150 11.0 0.24 1130
15 150 HB 0.5 9.0 0.13 0.46 150 240 11.0 0.35 2200
15 200 HB 0.5 9.0 0.13 0.46 150 220 11.0 0.35 1180
16 250 HB 0.5 9.0 0.13 0.46 150 190 11.0 0.35 1160
17,19 150 HB 0.5 9.0 0.11 0.41 100 200 11.0 0.30 1180
17,19 200 HB 0.5 9.0 0.11 0.41 100 180 11.0 0.30 1150
18,20 250 HB 0.5 9.0 0.11 0.41 100 150 11.0 0.30 1130
31,32 Incoloy 800 240 HB 0.5 6.4 0.08 0.26 25 45 11.0 0.24 332
33 Inconel 700 250 HB 0.5 6.4 0.08 0.26 25 45 11.0 0.24 330
34 Stellite 21 350 HB 0.5 6.4 0.08 0.26 25 45 11.0 0.24 330
36 TiAl6V4 - 0.5 6.4 0.08 0.29 40 65 11.0 0.27 555
37 T40 - 0.5 6.4 0.08 0.26 30 55 11.0 0.24 440
38 45 HRc 0.4 3.2 0.07 0.26 40 80 00.7 0.21 660
38 50 HRc 0.4 1.9 0.07 0.23 40 70 00.7 0.20 555
38 55 HRc 0.4 1.0 0.07 0.20 40 60 00.7 0.18 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.4 2.6 0.07 0.26 40 80 00.7 0.21 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.4 1.0 0.07 0.20 30 60 00.7 0.18 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.13 0.46 200 400 11.0 0.38 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
224
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 15.0 0.18 0.32 190 330 44.0 0.23 2250
2 190 HB 0.5 15.0 0.18 0.32 190 300 44.0 0.23 2220
3 250 HB 0.5 15.0 0.18 0.32 190 250 44.0 0.23 2200
6 180 HB 0.5 15.0 0.15 0.25 150 240 44.0 0.20 2200
4,6 230 HB 0.5 15.0 0.15 0.25 150 210 44.0 0.20 1180
5,7 280 HB 0.5 15.0 0.15 0.22 130 190 44.0 0.18 1150
8 350 HB 0.5 15.0 0.15 0.22 130 170 44.0 0.18 1140
10 220 HB 0.5 10.7 0.12 0.22 90 150 33.0 0.18 1130
10 280 HB 0.5 10.7 0.12 0.22 90 130 33.0 0.18 1120
11 320 HB 0.5 10.7 0.12 0.18 60 110 33.0 0.16 1100
11 350 HB 0.5 10.7 0.12 0.18 60 90 33.0 0.16 880
14 180 HB 0.5 15.0 0.15 0.25 190 250 44.0 0.20 2220
14 240 HB 0.5 15.0 0.12 0.22 160 210 44.0 0.20 1190
14 290 HB 0.5 10.7 0.12 0.18 70 130 33.0 0.16 1100
14 310 HB 0.5 10.7 0.12 0.18 70 120 33.0 0.16 990
12 200 HB 0.5 15.0 0.15 0.25 150 210 44.0 0.20 1190
13 42 HRc 0.5 10.7 0.15 0.20 90 150 33.0 0.16 1130
15 150 HB 0.5 15.0 0.18 0.32 150 240 44.0 0.23 2200
15 200 HB 0.5 15.0 0.18 0.32 150 220 44.0 0.23 1180
16 250 HB 0.5 15.0 0.18 0.32 150 190 44.0 0.23 1160
17,19 150 HB 0.5 15.0 0.15 0.28 100 200 44.0 0.20 1180
17,19 200 HB 0.5 15.0 0.15 0.28 100 180 44.0 0.20 1150
18,20 250 HB 0.5 15.0 0.15 0.28 100 150 44.0 0.20 1130
31,32 Incoloy 800 240 HB 0.5 10.7 0.12 0.18 25 45 33.0 0.16 332
33 Inconel 700 250 HB 0.5 10.7 0.12 0.18 25 45 33.0 0.16 330
34 Stellite 21 350 HB 0.5 10.7 0.12 0.18 25 45 33.0 0.16 330
36 TiAl6V4 - 0.5 10.7 0.12 0.20 40 65 33.0 0.18 555
37 T40 - 0.5 10.7 0.12 0.18 30 55 33.0 0.16 440
38 45 HRc 0.5 5.4 0.10 0.18 40 80 22.0 0.14 660
38 50 HRc 0.5 3.2 0.10 0.16 40 70 11.5 0.13 555
38 55 HRc 0.5 1.6 0.10 0.14 40 60 11.0 0.12 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 4.3 0.10 0.18 40 80 11.5 0.14 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.6 0.10 0.14 30 60 11.0 0.12 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 15.0 0.18 0.32 200 400 44.0 0.25 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
APKT 1604 PDTR – LT 30 | LT 3000
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
225
Machining Conditions
APKT 160416 PDTR – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 15.0 0.18 0.32 190 330 55.0 0.23 2250
2 190 HB 0.5 15.0 0.18 0.32 190 300 55.0 0.23 2220
3 250 HB 0.5 15.0 0.18 0.32 190 250 55.0 0.23 2200
6 180 HB 0.5 15.0 0.15 0.25 150 240 55.0 0.20 2200
4,6 230 HB 0.5 15.0 0.15 0.25 150 210 55.0 0.20 1180
5,7 280 HB 0.5 15.0 0.15 0.22 130 190 55.0 0.18 1150
8 350 HB 0.5 15.0 0.15 0.22 130 170 55.0 0.18 1140
10 220 HB 0.5 10.7 0.12 0.22 90 150 33.8 0.18 1130
10 280 HB 0.5 10.7 0.12 0.22 90 130 33.8 0.18 1120
11 320 HB 0.5 10.7 0.12 0.18 60 110 33.8 0.16 1100
11 350 HB 0.5 10.7 0.12 0.18 60 90 33.8 0.16 880
14 180 HB 0.5 15.0 0.15 0.25 190 250 55.0 0.20 2220
14 240 HB 0.5 15.0 0.12 0.22 160 210 55.0 0.20 1190
14 290 HB 0.5 10.7 0.12 0.18 70 130 33.8 0.16 1100
14 310 HB 0.5 10.7 0.12 0.18 70 120 33.8 0.16 990
12 200 HB 0.5 15.0 0.15 0.25 150 210 55.0 0.20 1190
13 42 HRc 0.5 10.7 0.15 0.20 90 150 33.8 0.16 1130
15 150 HB 0.5 15.0 0.18 0.32 150 240 55.0 0.23 2200
15 200 HB 0.5 15.0 0.18 0.32 150 220 55.0 0.23 1180
16 250 HB 0.5 15.0 0.18 0.32 150 190 55.0 0.23 1160
17,19 150 HB 0.5 15.0 0.15 0.28 100 200 55.0 0.20 1180
17,19 200 HB 0.5 15.0 0.15 0.28 100 180 55.0 0.20 1150
18,20 250 HB 0.5 15.0 0.15 0.28 100 150 55.0 0.20 1130
31,32 Incoloy 800 240 HB 0.5 10.7 0.12 0.18 25 45 33.8 0.16 332
33 Inconel 700 250 HB 0.5 10.7 0.12 0.18 25 45 33.8 0.16 330
34 Stellite 21 350 HB 0.5 10.7 0.12 0.18 25 45 33.8 0.16 330
36 TiAl6V4 - 0.5 10.7 0.12 0.20 40 65 33.8 0.18 555
37 T40 - 0.5 10.7 0.12 0.18 30 55 33.8 0.16 440
38 45 HRc 0.5 5.4 0.10 0.18 40 80 22.5 0.14 660
38 50 HRc 0.5 3.2 0.10 0.16 40 70 11.9 0.13 555
38 55 HRc 0.5 1.6 0.10 0.14 40 60 11.3 0.12 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 4.3 0.10 0.18 40 80 11.9 0.14 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.6 0.10 0.14 30 60 11.3 0.12 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 15.0 0.18 0.32 200 400 55.0 0.25 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
226
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 15.0 0.18 0.32 190 330 55.0 0.23 2250
2 190 HB 0.5 15.0 0.18 0.32 190 300 55.0 0.23 2220
3 250 HB 0.5 15.0 0.18 0.32 190 250 55.0 0.23 2200
6 180 HB 0.5 15.0 0.15 0.25 150 240 55.0 0.20 2200
4,6 230 HB 0.5 15.0 0.15 0.25 150 210 55.0 0.20 1180
5,7 280 HB 0.5 15.0 0.15 0.22 130 190 55.0 0.18 1150
8 350 HB 0.5 15.0 0.15 0.22 130 170 55.0 0.18 1140
10 220 HB 0.5 10.7 0.12 0.22 90 150 33.8 0.18 1130
10 280 HB 0.5 10.7 0.12 0.22 90 130 33.8 0.18 1120
11 320 HB 0.5 10.7 0.12 0.18 60 110 33.8 0.16 1100
11 350 HB 0.5 10.7 0.12 0.18 60 90 33.8 0.16 880
14 180 HB 0.5 15.0 0.15 0.25 190 250 55.0 0.20 2220
14 240 HB 0.5 15.0 0.12 0.22 160 210 55.0 0.20 1190
14 290 HB 0.5 10.7 0.12 0.18 70 130 33.8 0.16 1100
14 310 HB 0.5 10.7 0.12 0.18 70 120 33.8 0.16 990
12 200 HB 0.5 15.0 0.15 0.25 150 210 55.0 0.20 1190
13 42 HRc 0.5 10.7 0.15 0.20 90 150 33.8 0.16 1130
15 150 HB 0.5 15.0 0.18 0.32 150 240 55.0 0.23 2200
15 200 HB 0.5 15.0 0.18 0.32 150 220 55.0 0.23 1180
16 250 HB 0.5 15.0 0.18 0.32 150 190 55.0 0.23 1160
17,19 150 HB 0.5 15.0 0.15 0.28 100 200 55.0 0.20 1180
17,19 200 HB 0.5 15.0 0.15 0.28 100 180 55.0 0.20 1150
18,20 250 HB 0.5 15.0 0.15 0.28 100 150 55.0 0.20 1130
31,32 Incoloy 800 240 HB 0.5 10.7 0.12 0.18 25 45 33.8 0.16 332
33 Inconel 700 250 HB 0.5 10.7 0.12 0.18 25 45 33.8 0.16 330
34 Stellite 21 350 HB 0.5 10.7 0.12 0.18 25 45 33.8 0.16 330
36 TiAl6V4 - 0.5 10.7 0.12 0.20 40 65 33.8 0.18 555
37 T40 - 0.5 10.7 0.12 0.18 30 55 33.8 0.16 440
38 45 HRc 0.5 5.4 0.10 0.18 40 80 22.5 0.14 660
38 50 HRc 0.5 3.2 0.10 0.16 40 70 11.9 0.13 555
38 55 HRc 0.5 1.6 0.10 0.14 40 60 11.3 0.12 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 4.3 0.10 0.18 40 80 11.9 0.14 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.6 0.10 0.14 30 60 11.3 0.12 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 15.0 0.18 0.32 200 400 55.0 0.25 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
APKT 160424 PDTR – LT 30 | LT 3000
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
227
Machining Conditions
APKT 160432 PDTR – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 15.0 0.18 0.32 190 330 55.0 0.23 2250
2 190 HB 0.5 15.0 0.18 0.32 190 300 55.0 0.23 2220
3 250 HB 0.5 15.0 0.18 0.32 190 250 55.0 0.23 2200
6 180 HB 0.5 15.0 0.15 0.25 150 240 55.0 0.20 2200
4,6 230 HB 0.5 15.0 0.15 0.25 150 210 55.0 0.20 1180
5,7 280 HB 0.5 15.0 0.15 0.22 130 190 55.0 0.18 1150
8 350 HB 0.5 15.0 0.15 0.22 130 170 55.0 0.18 1140
10 220 HB 0.5 10.7 0.12 0.22 90 150 33.8 0.18 1130
10 280 HB 0.5 10.7 0.12 0.22 90 130 33.8 0.18 1120
11 320 HB 0.5 10.7 0.12 0.18 60 110 33.8 0.16 1100
11 350 HB 0.5 10.7 0.12 0.18 60 90 33.8 0.16 880
14 180 HB 0.5 15.0 0.15 0.25 190 250 55.0 0.20 2220
14 240 HB 0.5 15.0 0.12 0.22 160 210 55.0 0.20 1190
14 290 HB 0.5 10.7 0.12 0.18 70 130 33.8 0.16 1100
14 310 HB 0.5 10.7 0.12 0.18 70 120 33.8 0.16 990
12 200 HB 0.5 15.0 0.15 0.25 150 210 55.0 0.20 1190
13 42 HRc 0.5 10.7 0.15 0.20 90 150 33.8 0.16 1130
15 150 HB 0.5 15.0 0.18 0.32 150 240 55.0 0.23 2200
15 200 HB 0.5 15.0 0.18 0.32 150 220 55.0 0.23 1180
16 250 HB 0.5 15.0 0.18 0.32 150 190 55.0 0.23 1160
17,19 150 HB 0.5 15.0 0.15 0.28 100 200 55.0 0.20 1180
17,19 200 HB 0.5 15.0 0.15 0.28 100 180 55.0 0.20 1150
18,20 250 HB 0.5 15.0 0.15 0.28 100 150 55.0 0.20 1130
31,32 Incoloy 800 240 HB 0.5 10.7 0.12 0.18 25 45 33.8 0.16 332
33 Inconel 700 250 HB 0.5 10.7 0.12 0.18 25 45 33.8 0.16 330
34 Stellite 21 350 HB 0.5 10.7 0.12 0.18 25 45 33.8 0.16 330
36 TiAl6V4 - 0.5 10.7 0.12 0.20 40 65 33.8 0.18 555
37 T40 - 0.5 10.7 0.12 0.18 30 55 33.8 0.16 440
38 45 HRc 0.5 5.4 0.10 0.18 40 80 22.5 0.14 660
38 50 HRc 0.5 3.2 0.10 0.16 40 70 11.9 0.13 555
38 55 HRc 0.5 1.6 0.10 0.14 40 60 11.3 0.12 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 4.3 0.10 0.18 40 80 11.9 0.14 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.6 0.10 0.14 30 60 11.3 0.12 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 15.0 0.18 0.32 200 400 55.0 0.25 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
228
Machining Conditions
APKT 1705 PDTR – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 15.0 0.18 0.40 190 330 44.0 0.28 2250
2 190 HB 0.5 15.0 0.18 0.40 190 300 44.0 0.28 2220
3 250 HB 0.5 15.0 0.18 0.40 190 250 44.0 0.28 2200
6 180 HB 0.5 15.0 0.15 0.31 150 240 44.0 0.24 2200
4,6 230 HB 0.5 15.0 0.15 0.31 150 210 44.0 0.24 1180
5,7 280 HB 0.5 15.0 0.15 0.27 130 190 44.0 0.22 1150
8 350 HB 0.5 15.0 0.15 0.27 130 170 44.0 0.22 1140
10 220 HB 0.5 10.7 0.12 0.27 90 150 33.0 0.22 1130
10 280 HB 0.5 10.7 0.12 0.27 90 130 33.0 0.22 1120
11 320 HB 0.5 10.7 0.12 0.22 60 110 33.0 0.19 1100
11 350 HB 0.5 10.7 0.12 0.22 60 90 33.0 0.19 880
14 180 HB 0.5 15.0 0.15 0.31 190 250 44.0 0.24 2220
14 240 HB 0.5 15.0 0.12 0.27 160 210 44.0 0.24 1190
14 290 HB 0.5 10.7 0.12 0.22 70 130 33.0 0.19 1100
14 310 HB 0.5 10.7 0.12 0.22 70 120 33.0 0.19 990
12 200 HB 0.5 15.0 0.15 0.31 150 210 44.0 0.24 1190
13 42 HRc 0.5 10.7 0.15 0.25 90 150 33.0 0.19 1130
15 150 HB 0.5 15.0 0.18 0.40 150 240 44.0 0.28 2200
15 200 HB 0.5 15.0 0.18 0.40 150 220 44.0 0.28 1180
16 250 HB 0.5 15.0 0.18 0.40 150 190 44.0 0.28 1160
17,19 150 HB 0.5 15.0 0.15 0.35 100 200 44.0 0.24 1180
17,19 200 HB 0.5 15.0 0.15 0.35 100 180 44.0 0.24 1150
18,20 250 HB 0.5 15.0 0.15 0.35 100 150 44.0 0.24 1130
31,32 Incoloy 800 240 HB 0.5 10.7 0.12 0.22 25 45 33.0 0.19 332
33 Inconel 700 250 HB 0.5 10.7 0.12 0.22 25 45 33.0 0.19 330
34 Stellite 21 350 HB 0.5 10.7 0.12 0.22 25 45 33.0 0.19 330
36 TiAl6V4 - 0.5 10.7 0.12 0.25 40 65 33.0 0.22 555
37 T40 - 0.5 10.7 0.12 0.22 30 55 33.0 0.19 440
38 45 HRc 0.5 5.4 0.10 0.22 40 80 22.0 0.17 660
38 50 HRc 0.5 3.2 0.10 0.20 40 70 11.5 0.16 555
38 55 HRc 0.5 1.6 0.10 0.17 40 60 11.0 0.14 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 4.3 0.10 0.22 40 80 11.5 0.17 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.6 0.10 0.17 30 60 11.0 0.14 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 15.0 0.18 0.40 200 400 44.0 0.30 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
229
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
A P M T
Shape Clearance Angle Toleranced ± 0.05m ± 0.08s ± 0.13
11°
Fixing,Chipbreaker
sl
Ø dm
Helical Interpolation SurfacingSlottingShoulder Milling
M0002218
M0002183
M0002216
M0004161
0.70
0.66
0.70
0.40
Right
Right
Right
Right
4.82
4.82
3.52
3.38
17.11
17.01
11.45
9.94
APMT 160408 PDTR LT 3000
APMT 1604 PDTR LT 3000
APMT 1135 PDTR LT 3000
APMT 0903 PDTR LT 3000
Insert Designation Catalog Nr.Directions rl
LT 3000 Multi-MatTM General Usage – Premium
M0001733
M0001134
M0001133
0.70
0.66
0.70
Right
Right
Right
4.82
4.82
3.52
17.11
17.01
11.45
APMT 160408 PDTR LT 30
APMT 1604 PDTR LT 30
APMT 1135 PDTR LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
APMT
Pocket MillingPlungingRamping Down
MILLING
230
Cutters
* On request
* On request
Screw:Key:
M2002778M2002912
Key:Screw: M2000597
M2000602
Key:Screw: M2000597
M2000602
End Mill for APMT 1135 PDTR
End Mill for APMT 1604 PDTR
Cutter Designation
Cutter Designation
Catalog Nr.
Catalog Nr.
D
D
z
z
d
d
L1
L1
L
L
Ap
Ap
LT 760 W-W-D032/3*
LT 755 WL-W-D032/4*
M2001663
M2001661
32
32
3
5
32
25
100
40
200
200
15
9
LT 755 W-W-D020/3* M200165520 320 35 120 9 7
3
3
LT 760 WL-W-D025/2*
LT 755 WL-W-D025/4*
M2001665
M2001660
25
25
2
4
25
25
70
40
200
200
15
9
5
5
LT 755 W-W-D020/3* M200165520 320 35 120 9 7
LT 760 WL-W-D040/4* M200166740 432 100 250 15
LT 755 WL-W-D016/2* M200165816 216 30 150 9 12
2.5
LT 760 W-W-D025/2* M200166225 225 50 150 15 5
LT 755 W-W-D025/4* M200165625 425 40 150 9 5
LT 760 W-W-D040/4* M200166440 432 100 200 15
LT 755 WL-W-D020/2* M200165920 220 35 150 9 7
2.5
LT 760 W-W-D032/3* M200166332 332 100 200 15 3
LT 755 WL-W-D032/4* M200166132 525 40 200 9 3
LT 760 WL-W-D032/3*
LT 755 W-W-D032/5*
M2001666
M2001657
32
32
3
5
32
25
100
40
250
150
15
9
LT 755 W-W-D016/2* M200165416 216 30 120 9 12
3
3
α Ramp°
α Ramp°
Dd
Ap
LL1
90°
Shell Mill for APMT 1604 PDTR
Bezeichnung Katalognr.D zd L1 L Ap
LT 760 M-W-D080/7* M200167080 727 - 50 15 1.4
LT 760 M-W-D100/8* M2001671100 832 - 50 15 1.1
LT 760 M-W-D050/5* M200166850 522 - 40 15 2.2
LT 760 M-W-D125/9* M2001672125 940 - 63 15 0.8
LT 760 M-W-D063/6* M200166963 622 - 40 15 1.8
α Ramp°
* On request
D
d
Ap
L
90°
MILLING
231
Machining Conditions
APMT 0903 PDTR – LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 8.0 0.11 0.20 190 330 22.0 0.14 2250
2 190 HB 0.5 8.0 0.11 0.20 190 300 22.0 0.14 2220
3 250 HB 0.5 8.0 0.11 0.20 190 250 22.0 0.14 2200
6 180 HB 0.5 8.0 0.09 0.16 150 240 22.0 0.12 2200
4,6 230 HB 0.5 8.0 0.09 0.16 150 210 22.0 0.12 1180
5,7 280 HB 0.5 8.0 0.09 0.14 130 190 22.0 0.11 1150
8 350 HB 0.5 8.0 0.09 0.14 130 170 22.0 0.11 1140
10 220 HB 0.5 5.7 0.07 0.14 90 150 11.5 0.11 1130
10 280 HB 0.5 5.7 0.07 0.14 90 130 11.5 0.11 1120
11 320 HB 0.5 5.7 0.07 0.11 60 110 11.5 0.10 1100
11 350 HB 0.5 5.7 0.07 0.11 60 90 11.5 0.10 880
14 180 HB 0.5 8.0 0.09 0.16 190 250 22.0 0.12 2220
14 240 HB 0.5 8.0 0.07 0.14 160 210 22.0 0.12 1190
14 290 HB 0.5 5.7 0.07 0.11 70 130 11.5 0.10 1100
14 310 HB 0.5 5.7 0.07 0.11 70 120 11.5 0.10 990
12 200 HB 0.5 8.0 0.09 0.16 150 210 22.0 0.12 1190
13 42 HRc 0.5 5.7 0.09 0.12 90 150 11.5 0.10 1130
15 150 HB 0.5 8.0 0.11 0.20 150 240 22.0 0.14 2200
15 200 HB 0.5 8.0 0.11 0.20 150 220 22.0 0.14 1180
16 250 HB 0.5 8.0 0.11 0.20 150 190 22.0 0.14 1160
17,19 150 HB 0.5 8.0 0.09 0.17 100 200 22.0 0.12 1180
17,19 200 HB 0.5 8.0 0.09 0.17 100 180 22.0 0.12 1150
18,20 250 HB 0.5 8.0 0.09 0.17 100 150 22.0 0.12 1130
31,32 Incoloy 800 240 HB 0.5 5.7 0.07 0.11 25 45 11.5 0.10 332
33 Inconel 700 250 HB 0.5 5.7 0.07 0.11 25 45 11.5 0.10 330
34 Stellite 21 350 HB 0.5 5.7 0.07 0.11 25 45 11.5 0.10 330
36 TiAl6V4 - 0.5 5.7 0.07 0.12 40 65 11.5 0.11 555
37 T40 - 0.5 5.7 0.07 0.11 30 55 11.5 0.10 440
38 45 HRc 0.5 2.9 0.06 0.11 40 80 11.0 0.09 660
38 50 HRc 0.5 1.7 0.06 0.10 40 70 00.8 0.08 555
38 55 HRc 0.5 1.2 0.06 0.09 40 60 00.5 0.07 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.3 0.06 0.11 40 80 00.8 0.09 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.2 0.06 0.09 30 60 00.5 0.07 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 8.0 0.11 0.20 200 400 2.0 0.16 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
232
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 10.0 0.13 0.22 190 330 22.0 0.15 2250
2 190 HB 0.5 10.0 0.13 0.22 190 300 22.0 0.15 2220
3 250 HB 0.5 10.0 0.13 0.22 190 250 22.0 0.15 2200
6 180 HB 0.5 10.0 0.11 0.18 150 240 22.0 0.13 2200
4,6 230 HB 0.5 10.0 0.11 0.18 150 210 22.0 0.13 1180
5,7 280 HB 0.5 10.0 0.11 0.15 130 190 22.0 0.12 1150
8 350 HB 0.5 10.0 0.11 0.15 130 170 22.0 0.12 1140
10 220 HB 0.5 7.2 0.08 0.15 90 150 11.5 0.12 1130
10 280 HB 0.5 7.2 0.08 0.15 90 130 11.5 0.12 1120
11 320 HB 0.5 7.2 0.08 0.13 60 110 11.5 0.10 1100
11 350 HB 0.5 7.2 0.08 0.13 60 90 11.5 0.10 880
14 180 HB 0.5 10.0 0.11 0.18 190 250 22.0 0.13 2220
14 240 HB 0.5 10.0 0.08 0.15 160 210 22.0 0.13 1190
14 290 HB 0.5 7.2 0.08 0.13 70 130 11.5 0.10 1100
14 310 HB 0.5 7.2 0.08 0.13 70 120 11.5 0.10 990
12 200 HB 0.5 10.0 0.11 0.18 150 210 22.0 0.13 1190
13 42 HRc 0.5 7.2 0.08 0.14 90 150 11.5 0.10 1130
15 150 HB 0.5 10.0 0.13 0.22 150 240 22.0 0.15 2200
15 200 HB 0.5 10.0 0.13 0.22 150 220 22.0 0.15 1180
16 250 HB 0.5 10.0 0.13 0.22 150 190 22.0 0.15 1160
17,19 150 HB 0.5 10.0 0.11 0.20 100 200 22.0 0.13 1180
17,19 200 HB 0.5 10.0 0.11 0.20 100 180 22.0 0.13 1150
18,20 250 HB 0.5 10.0 0.11 0.20 100 150 22.0 0.13 1130
31,32 Incoloy 800 240 HB 0.5 7.2 0.08 0.13 25 45 11.5 0.10 332
33 Inconel 700 250 HB 0.5 7.2 0.08 0.13 25 45 11.5 0.10 330
34 Stellite 21 350 HB 0.5 7.2 0.08 0.13 25 45 11.5 0.10 330
36 TiAl6V4 - 0.5 7.2 0.08 0.14 40 65 11.5 0.12 555
37 T40 - 0.5 7.2 0.08 0.13 30 55 11.5 0.10 440
38 45 HRc 0.5 3.6 0.07 0.13 40 80 11.0 0.09 660
38 50 HRc 0.5 2.1 0.07 0.11 40 70 00.8 0.08 555
38 55 HRc 0.5 1.1 0.07 0.10 40 60 00.5 0.08 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.9 0.07 0.13 40 80 00.8 0.09 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.1 0.07 0.10 30 60 00.5 0.08 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 10.0 0.13 0.22 200 400 2.0 0.16 280
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5X2CrNiN23-4,
S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
APMT 1135 PDTR – LT 30 | LT 3000
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
233
Machining Conditions
APMT 1604 PDTR – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 15.0 0.16 0.30 190 330 44.0 0.21 2250
2 190 HB 0.5 15.0 0.16 0.30 190 300 44.0 0.21 2220
3 250 HB 0.5 15.0 0.16 0.30 190 250 44.0 0.21 2200
6 180 HB 0.5 15.0 0.14 0.23 150 240 44.0 0.18 2200
4,6 230 HB 0.5 15.0 0.14 0.23 150 210 44.0 0.18 1180
5,7 280 HB 0.5 15.0 0.14 0.20 130 190 44.0 0.16 1150
8 350 HB 0.5 15.0 0.14 0.20 130 170 44.0 0.16 1140
10 220 HB 0.5 10.7 0.11 0.20 90 150 33.0 0.16 1130
10 280 HB 0.5 10.7 0.11 0.20 90 130 33.0 0.16 1120
11 320 HB 0.5 10.7 0.11 0.17 60 110 33.0 0.14 1100
11 350 HB 0.5 10.7 0.11 0.17 60 90 33.0 0.14 880
14 180 HB 0.5 15.0 0.14 0.23 190 250 44.0 0.18 2220
14 240 HB 0.5 15.0 0.11 0.20 160 210 44.0 0.18 1190
14 290 HB 0.5 10.7 0.11 0.17 70 130 33.0 0.14 1100
14 310 HB 0.5 10.7 0.11 0.17 70 120 33.0 0.14 990
12 200 HB 0.5 15.0 0.14 0.23 150 210 44.0 0.18 1190
13 42 HRc 0.5 10.7 0.14 0.19 90 150 33.0 0.14 1130
15 150 HB 0.5 15.0 0.16 0.30 150 240 44.0 0.21 2200
15 200 HB 0.5 15.0 0.16 0.30 150 220 44.0 0.21 1180
16 250 HB 0.5 15.0 0.16 0.30 150 190 44.0 0.21 1160
17,19 150 HB 0.5 15.0 0.14 0.26 100 200 44.0 0.18 1180
17,19 200 HB 0.5 15.0 0.14 0.26 100 180 44.0 0.18 1150
18,20 250 HB 0.5 15.0 0.14 0.26 100 150 44.0 0.18 1130
31,32 Incoloy 800 240 HB 0.5 10.7 0.11 0.17 25 45 33.0 0.14 332
33 Inconel 700 250 HB 0.5 10.7 0.11 0.17 25 45 33.0 0.14 330
34 Stellite 21 350 HB 0.5 10.7 0.11 0.17 25 45 33.0 0.14 330
36 TiAl6V4 - 0.5 10.7 0.11 0.19 40 65 33.0 0.16 555
37 T40 - 0.5 10.7 0.11 0.17 30 55 33.0 0.14 440
38 45 HRc 0.5 5.4 0.09 0.17 40 80 22.0 0.13 660
38 50 HRc 0.5 3.2 0.09 0.15 40 70 11.5 0.12 555
38 55 HRc 0.5 1.6 0.09 0.13 40 60 11.0 0.11 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 4.3 0.09 0.17 40 80 11.5 0.13 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.6 0.09 0.13 30 60 11.0 0.11 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 15.0 0.16 0.30 200 400 44.0 0.23 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
234
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 15.0 0.16 0.30 190 330 44.0 0.21 2250
2 190 HB 0.5 15.0 0.16 0.30 190 300 44.0 0.21 2220
3 250 HB 0.5 15.0 0.16 0.30 190 250 44.0 0.21 2200
6 180 HB 0.5 15.0 0.14 0.23 150 240 44.0 0.18 2200
4,6 230 HB 0.5 15.0 0.14 0.23 150 210 44.0 0.18 1180
5,7 280 HB 0.5 15.0 0.14 0.20 130 190 44.0 0.16 1150
8 350 HB 0.5 15.0 0.14 0.20 130 170 44.0 0.16 1140
10 220 HB 0.5 10.7 0.11 0.20 90 150 33.0 0.16 1130
10 280 HB 0.5 10.7 0.11 0.20 90 130 33.0 0.16 1120
11 320 HB 0.5 10.7 0.11 0.17 60 110 33.0 0.14 1100
11 350 HB 0.5 10.7 0.11 0.17 60 90 33.0 0.14 880
14 180 HB 0.5 15.0 0.14 0.23 190 250 44.0 0.18 2220
14 240 HB 0.5 15.0 0.11 0.20 160 210 44.0 0.18 1190
14 290 HB 0.5 10.7 0.11 0.17 70 130 33.0 0.14 1100
14 310 HB 0.5 10.7 0.11 0.17 70 120 33.0 0.14 990
12 200 HB 0.5 15.0 0.14 0.23 150 210 44.0 0.18 1190
13 42 HRc 0.5 10.7 0.14 0.19 90 150 33.0 0.14 1130
15 150 HB 0.5 15.0 0.16 0.30 150 240 44.0 0.21 2200
15 200 HB 0.5 15.0 0.16 0.30 150 220 44.0 0.21 1180
16 250 HB 0.5 15.0 0.16 0.30 150 190 44.0 0.21 1160
17,19 150 HB 0.5 15.0 0.14 0.26 100 200 44.0 0.18 1180
17,19 200 HB 0.5 15.0 0.14 0.26 100 180 44.0 0.18 1150
18,20 250 HB 0.5 15.0 0.14 0.26 100 150 44.0 0.18 1130
31,32 Incoloy 800 240 HB 0.5 10.7 0.11 0.17 25 45 33.0 0.14 332
33 Inconel 700 250 HB 0.5 10.7 0.11 0.17 25 45 33.0 0.14 330
34 Stellite 21 350 HB 0.5 10.7 0.11 0.17 25 45 33.0 0.14 330
36 TiAl6V4 - 0.5 10.7 0.11 0.19 40 65 33.0 0.16 555
37 T40 - 0.5 10.7 0.11 0.17 30 55 33.0 0.14 440
38 45 HRc 0.5 5.4 0.09 0.17 40 80 22.0 0.13 660
38 50 HRc 0.5 3.2 0.09 0.15 40 70 11.5 0.12 555
38 55 HRc 0.5 1.6 0.09 0.13 40 60 11.0 0.11 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 4.3 0.09 0.17 40 80 11.5 0.13 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.6 0.09 0.13 30 60 11.0 0.11 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 15.0 0.16 0.30 200 400 44.0 0.23 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
APMT 160408 PDTR – LT 30 | LT 3000
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
235
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
L D M T
Shape Clearance Angle Toleranced ± 0.05m ± 0.08s ± 0.13
15°
Fixing,Chipbreaker
sl
Ø dm
Shoulder Milling SurfacingSlotting
M00017720.74 Right4.7915.71LDMT 1504 PDSR LT30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
LDMT
Pocket Milling
PlungingRamping Down Helical Interpolation
MILLING
236
Cutters
* On request
* On request
Key:Screw: M2001418
M2000602
End Mill for LDMT 1504 PDSR
Cutter Designation Catalog Nr.D zd L1 L Ap
LT 770 W-W-D032/3* M200182332 335 50 110 15 3
LT 770 WL-W-D25/2* M200182525 225 44 150 15 5
LT 770 W-W-D040/4* M200182440 432 45 115 15 2.5
LT 770 W-W-D025/2* M200182225 225 44 100 15 5
LT 770 WL-W-D32/3* M200182632 325 50 150 15 3
α Ramp°
Shell Mill for LDMT 1504 PDSR
Screw:Key:
M2001418M2000602
Cutter Designation
LT 770 M-W-D040/4*
LT 770 M-W-D080/7*
LT 770 M-W-D125/9*
LT 770 M-W-D100/8*
LT 770 M-W-D160/9*
LT 770 M-W-D050/5*
LT 770 M-W-D063/6*
Catalog Nr.
M2001827
M2001846
M2001831
M2001830
M2001832
M2001828
M2001829
D
40
80
125
100
160
50
63
z
4
7
9
8
9
5
6
Ap
15
15
15
15
15
15
15
d
16
27
40
32
40
22
22
L
40
50
63
50
63
40
40
α Ramp°
1.4
0.8
1.1
-
2.5
2.2
1.8
D
d
Ap
L
90°
Dd
Ap
L1
90°
MILLING
237
Machining Conditions
LDMT 1504 PDSR – LT 30
min max min max min max D.O.C. Feed
1 125 HB 0.5 14.0 0.18 0.32 190 330 44.0 0.23 2250
2 190 HB 0.5 14.0 0.18 0.32 190 300 44.0 0.23 2220
3 250 HB 0.5 14.0 0.18 0.32 190 250 44.0 0.23 2200
6 180 HB 0.5 14.0 0.15 0.25 150 240 44.0 0.20 2200
4,6 230 HB 0.5 14.0 0.15 0.25 150 210 44.0 0.20 1180
5,7 280 HB 0.5 14.0 0.15 0.22 130 190 44.0 0.18 1150
8 350 HB 0.5 14.0 0.15 0.22 130 170 44.0 0.18 1140
10 220 HB 0.5 10.0 0.12 0.22 90 150 33.0 0.18 1130
10 280 HB 0.5 10.0 0.12 0.22 90 130 33.0 0.18 1120
11 320 HB 0.5 10.0 0.12 0.18 60 110 33.0 0.16 1100
11 350 HB 0.5 10.0 0.12 0.18 60 90 33.0 0.16 880
14 180 HB 0.5 14.0 0.15 0.25 190 250 44.0 0.20 2220
14 240 HB 0.5 14.0 0.12 0.22 160 210 44.0 0.20 1190
14 290 HB 0.5 10.0 0.12 0.18 70 130 33.0 0.16 1100
14 310 HB 0.5 10.0 0.12 0.18 70 120 33.0 0.16 990
12 200 HB 0.5 14.0 0.15 0.25 150 210 44.0 0.20 1190
13 42 HRc 0.5 10.0 0.15 0.20 90 150 33.0 0.16 1130
15 150 HB 0.5 14.0 0.18 0.32 150 240 44.0 0.23 2200
15 200 HB 0.5 14.0 0.18 0.32 150 220 44.0 0.23 1180
16 250 HB 0.5 14.0 0.18 0.32 150 190 44.0 0.23 1160
17,19 150 HB 0.5 14.0 0.15 0.28 100 200 44.0 0.20 1180
17,19 200 HB 0.5 14.0 0.15 0.28 100 180 44.0 0.20 1150
18,20 250 HB 0.5 14.0 0.15 0.28 100 150 44.0 0.20 1130
31,32 Incoloy 800 240 HB 0.5 10.0 0.12 0.18 25 45 33.0 0.16 332
33 Inconel 700 250 HB 0.5 10.0 0.12 0.18 25 45 33.0 0.16 330
34 Stellite 21 350 HB 0.5 10.0 0.12 0.18 25 45 33.0 0.16 330
36 TiAl6V4 - 0.5 10.0 0.12 0.20 40 65 33.0 0.18 555
37 T40 - 0.5 10.0 0.12 0.18 30 55 33.0 0.16 440
38 45 HRc 0.5 5.0 0.10 0.18 40 80 22.0 0.14 660
38 50 HRc 0.5 3.0 0.10 0.16 40 70 11.5 0.13 555
38 55 HRc 0.5 1.5 0.10 0.14 40 60 11.0 0.12 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 4.0 0.10 0.18 40 80 11.5 0.14 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.14 30 60 11.0 0.12 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 14.0 0.18 0.32 200 400 44.0 0.25 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
238
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
O D M T
Shape Clearance Angle Tolerances ± 0.13For l = 05, d ± 0.08 m ± 0.13For l = 06, d ± 0.10 m ± 0.15
15°135°
m
l
Ø d
Fixing,Chipbreaker
s
Chamfering Surfacing
MILLING
M0001104
M0000664
0.80
0.80
Right
Right
Catalog Nr.Directionr
5.56
4.76
6.58
5.08
ODMT 060508 TN LT 30
ODMT 0504 ZZTR LT 30
Insert Designation sl
LT 30 Multi-MatTM General Usage – Standard
M0002219
M0003399
0.80
0.80
Right
Right
5.56
4.76
6.58
5.08
ODMT 060508 TN LT 3000
ODMT 0504 ZZTR LT 3000
Insert Designation Catalog Nr.Directions rl
LT 3000 Multi-MatTM General Usage – Premium
MILLING
239
Cutters
ODMT
Shell Mill for ODMT 060508 TN
Screw:Key:
M2002733M2000603
Cutter Designation
LT 820 M-D-D080/5*
LT 820 M-D-D063/5*
LT 820 M-D-D160/9*
LT 820 M-D-D100/6*
LT 820 M-D-D125/7*
Catalog Nr.
M2000711
M2003837
M2000714
M2000712
M2000713
D
90
63
170
110
135
z
5
5
9
6
7
Ap
3.5
3.5
3.5
3.5
3.5
D1
80
53
160
100
125
d
27
22
40
32
40
L
50
50
63
50
63
DD1
d
Ap
L
43°
* On request
MILLING
240
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 3.5 0.22 0.51 190 330 22.5 0.37 2250
2 190 HB 0.5 3.5 0.22 0.51 190 300 22.5 0.37 2220
3 250 HB 0.5 3.5 0.22 0.51 190 250 22.5 0.37 2200
6 180 HB 0.5 3.5 0.18 0.40 150 240 22.5 0.32 2200
4,6 230 HB 0.5 3.5 0.18 0.40 150 210 22.5 0.32 1180
5,7 280 HB 0.5 3.5 0.18 0.35 130 190 22.5 0.29 1150
8 350 HB 0.5 3.5 0.18 0.35 130 170 22.5 0.29 1140
10 220 HB 0.5 2.5 0.14 0.35 90 150 11.9 0.29 1130
10 280 HB 0.5 2.5 0.14 0.35 90 130 11.9 0.29 1120
11 320 HB 0.5 2.5 0.14 0.29 60 110 11.9 0.26 1100
11 350 HB 0.5 2.5 0.14 0.29 60 90 11.9 0.26 880
14 180 HB 0.5 3.5 0.18 0.35 190 250 22.5 0.29 2220
14 240 HB 0.5 3.5 0.14 0.32 160 210 22.5 0.29 1190
14 290 HB 0.5 2.5 0.14 0.29 70 130 11.9 0.26 1100
14 310 HB 0.5 2.5 0.14 0.29 70 120 11.9 0.26 990
12 200 HB 0.5 3.5 0.18 0.35 150 210 22.5 0.29 1190
13 42 HRc 0.5 2.5 0.18 0.32 90 150 11.9 0.26 1130
15 150 HB 0.5 3.5 0.22 0.51 150 240 22.5 0.37 2200
15 200 HB 0.5 3.5 0.22 0.51 150 220 22.5 0.37 1180
16 250 HB 0.5 3.5 0.22 0.51 150 190 22.5 0.37 1160
17,19 150 HB 0.5 3.5 0.18 0.45 100 200 22.5 0.32 1180
17,19 200 HB 0.5 3.5 0.18 0.45 100 180 22.5 0.32 1150
18,20 250 HB 0.5 3.5 0.18 0.45 100 150 22.5 0.32 1130
31,32 Incoloy 800 240 HB 0.5 2.5 0.14 0.29 25 45 11.9 0.26 332
33 Inconel 700 250 HB 0.5 2.5 0.14 0.29 25 45 11.9 0.26 330
34 Stellite 21 350 HB 0.5 2.5 0.14 0.29 25 45 11.9 0.26 330
36 TiAl6V4 - 0.5 2.5 0.14 0.32 40 65 11.9 0.29 555
37 T40 - 0.5 2.5 0.14 0.29 30 55 11.9 0.26 440
38 45 HRc 0.4 1.3 0.12 0.29 40 80 11.3 0.22 660
38 50 HRc 0.4 0.8 0.12 0.26 40 70 00.9 0.21 555
38 55 HRc 0.4 0.4 0.12 0.22 40 60 00.6 0.19 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.4 1.0 0.12 0.29 40 80 00.9 0.22 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.4 0.4 0.12 0.22 30 60 00.6 0.19 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.5 0.22 0.51 200 400 22.5 0.40 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
ODMT 0504 ZZTR – LT 30 | LT 3000
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
241
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 4.0 0.22 0.54 190 330 22.5 0.39 2250
2 190 HB 0.5 4.0 0.22 0.54 190 300 22.5 0.39 2220
3 250 HB 0.5 4.0 0.22 0.54 190 250 22.5 0.39 2200
6 180 HB 0.5 4.0 0.18 0.43 150 240 22.5 0.34 2200
4,6 230 HB 0.5 4.0 0.18 0.43 150 210 22.5 0.34 1180
5,7 280 HB 0.5 4.0 0.18 0.37 130 190 22.5 0.31 1150
8 350 HB 0.5 4.0 0.18 0.37 130 170 22.5 0.31 1140
10 220 HB 0.5 2.9 0.14 0.37 90 150 11.9 0.31 1130
10 280 HB 0.5 2.9 0.14 0.37 90 130 11.9 0.31 1120
11 320 HB 0.5 2.9 0.14 0.31 60 110 11.9 0.27 1100
11 350 HB 0.5 2.9 0.14 0.31 60 90 11.9 0.27 880
14 180 HB 0.5 4.0 0.18 0.37 190 250 22.5 0.31 2220
14 240 HB 0.5 4.0 0.14 0.34 160 210 22.5 0.31 1190
14 290 HB 0.5 2.9 0.14 0.31 70 130 11.9 0.27 1100
14 310 HB 0.5 2.9 0.14 0.31 70 120 11.9 0.27 990
12 200 HB 0.5 4.0 0.18 0.37 150 210 22.5 0.31 1190
13 42 HRc 0.5 2.9 0.18 0.34 90 150 11.9 0.27 1130
15 150 HB 0.5 4.0 0.22 0.54 150 240 22.5 0.39 2200
15 200 HB 0.5 4.0 0.22 0.54 150 220 22.5 0.39 1180
16 250 HB 0.5 4.0 0.22 0.54 150 190 22.5 0.39 1160
17,19 150 HB 0.5 4.0 0.18 0.48 100 200 22.5 0.34 1180
17,19 200 HB 0.5 4.0 0.18 0.48 100 180 22.5 0.34 1150
18,20 250 HB 0.5 4.0 0.18 0.48 100 150 22.5 0.34 1130
31,32 Incoloy 800 240 HB 0.5 2.9 0.14 0.31 25 45 11.9 0.27 332
33 Inconel 700 250 HB 0.5 2.9 0.14 0.31 25 45 11.9 0.27 330
34 Stellite 21 350 HB 0.5 2.9 0.14 0.31 25 45 11.9 0.27 330
36 TiAl6V4 - 0.5 2.9 0.14 0.34 40 65 11.9 0.31 555
37 T40 - 0.5 2.9 0.14 0.31 30 55 11.9 0.27 440
38 45 HRc 0.4 1.4 0.12 0.31 40 80 11.3 0.24 660
38 50 HRc 0.4 1.1 0.12 0.27 40 70 00.9 0.22 555
38 55 HRc 0.4 0.9 0.12 0.24 40 60 00.6 0.20 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.4 1.1 0.12 0.31 40 80 00.9 0.24 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.4 0.9 0.12 0.24 30 60 00.6 0.20 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.0 0.22 0.54 200 400 22.5 0.43 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
ODMT 060508 TN – LT 30 | LT 3000
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
242
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
O D M W
Shape Clearance Angle Toleranced ± 0.10m ± 0.15s ± 0.13
s
15°135°
m
l
Ø d
Fixing,Chipbreaker
Chamfering Surfacing
M00004510.80 Right5.566.58ODMW 060508 TN LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
M00034000.80 Right5.566.58ODMW 060508 TN LT 3000
Insert Designation Catalog Nr.Directions rl
LT 3000 Multi-MatTM General Usage – Premium
Shell Mill for ODMW 060508 TN
Screw:Key:
M2002733M2000603
Cutter Designation
LT 820 M-D-D080/5*
LT 820 M-D-D063/5*
LT 820 M-D-D160/9*
LT 820 M-D-D100/6*
LT 820 M-D-D125/7*
Catalog Nr.
M2000711
M2003837
M2000714
M2000712
M2000713
D
90
63
170
110
135
z
5
5
9
6
7
Ap
3.5
3.5
3.5
3.5
3.5
D1
80
53
160
100
125
d
27
22
40
32
40
L
50
50
63
50
63
* On request
MILLING
243
Machining Conditions
ODMW
ODMW 060508 TN – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 4.0 0.22 0.58 190 330 33.0 0.41 2250
2 190 HB 0.5 4.0 0.22 0.58 190 300 33.0 0.41 2220
3 250 HB 0.5 4.0 0.22 0.58 190 250 33.0 0.41 2200
6 180 HB 0.5 4.0 0.18 0.45 150 240 33.0 0.36 2200
4,6 230 HB 0.5 4.0 0.18 0.45 150 210 33.0 0.36 1180
5,7 280 HB 0.5 4.0 0.18 0.40 130 190 33.0 0.32 1150
8 350 HB 0.5 4.0 0.18 0.40 130 170 33.0 0.32 1140
10 220 HB 0.5 2.9 0.14 0.40 90 150 22.3 0.32 1130
10 280 HB 0.5 2.9 0.14 0.40 90 130 22.3 0.32 1120
11 320 HB 0.5 2.9 0.14 0.32 60 110 22.3 0.29 1100
11 350 HB 0.5 2.9 0.14 0.32 60 90 22.3 0.29 880
15 150 HB 0.5 4.0 0.22 0.58 150 240 33.0 0.41 2200
15 200 HB 0.5 4.0 0.22 0.58 150 220 33.0 0.41 1180
16 250 HB 0.5 4.0 0.22 0.58 150 190 33.0 0.41 1160
17,19 150 HB 0.5 4.0 0.18 0.50 100 200 33.0 0.36 1180
17,19 200 HB 0.5 4.0 0.18 0.50 100 180 33.0 0.36 1150
18,20 250 HB 0.5 4.0 0.18 0.50 100 150 33.0 0.36 1130
38 45 HRc 0.4 1.4 0.12 0.32 40 80 11.1 0.25 660
38 50 HRc 0.4 1.1 0.12 0.29 40 70 00.9 0.23 555
38 55 HRc 0.4 0.9 0.12 0.25 40 60 00.7 0.22 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.4 1.1 0.12 0.32 40 80 00.9 0.25 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.4 0.9 0.12 0.25 30 60 00.7 0.22 440
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Cast
Iron
Grey
Malleable & Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
244
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
O F E R
Shape Clearance Angle Toleranced ± 0.025m ± 0.025s ± 0.025
25°135°
m
l
Ø d
Fixing,Chipbreaker
s
Chamfering Surfacing
M00000330.80 Right4.767.43OFER 070405 TN LT 30
Catalog Nr.Insert Designation Directions rl
LT 30 Multi-MatTM General Usage – Standard
M00034010.80 Right4.767.43OFER 070405 TN LT 3000
Insert Designation Catalog Nr.Directions rl
LT 3000 Multi-MatTM General Usage – Premium
MILLING
245
Cutters
Shell Mill for OFER 070405 TN
Screw:Key:
M2000606M2000609
Cutter Designation
LT 880 M-W-D080/5*
LT 880 M-W-D063/4*
LT 880 M-D-D160/10*
LT 880 M-W-D100/6*
LT 880 M-W-D125/8*
Catalog Nr.
M2000510
M2000508
M2000513
M2000511
M2000512
D
90
73
170
110
135
z
5
4
10
6
8
Ap
5
5
5
5
5
D1
80
63
160
100
125
d
27
22
40
32
40
L
50
40
63
50
63
DD1
d
Ap
L
43°
* On request OFER
MILLING
246
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 4.5 0.22 0.51 190 330 33.0 0.37 2250
2 190 HB 0.5 4.5 0.22 0.51 190 300 33.0 0.37 2220
3 250 HB 0.5 4.5 0.22 0.51 190 250 33.0 0.37 2200
6 180 HB 0.5 4.5 0.18 0.40 150 240 33.0 0.32 2200
4,6 230 HB 0.5 4.5 0.18 0.40 150 210 33.0 0.32 1180
5,7 280 HB 0.5 4.5 0.18 0.35 130 190 33.0 0.29 1150
8 350 HB 0.5 4.5 0.18 0.35 130 170 33.0 0.29 1140
10 220 HB 0.5 3.2 0.14 0.35 90 150 22.2 0.29 1130
10 280 HB 0.5 3.2 0.14 0.35 90 130 22.2 0.29 1120
11 320 HB 0.5 3.2 0.14 0.29 60 110 22.2 0.26 1100
11 350 HB 0.5 3.2 0.14 0.29 60 90 22.2 0.26 880
14 180 HB 0.5 4.5 0.18 0.35 190 250 33.0 0.29 2220
14 240 HB 0.5 4.5 0.14 0.32 160 210 33.0 0.29 1190
14 290 HB 0.5 3.2 0.14 0.29 70 130 22.2 0.26 1100
14 310 HB 0.5 3.2 0.14 0.29 70 120 22.2 0.26 990
12 200 HB 0.5 4.5 0.18 0.35 150 210 33.0 0.29 1190
13 42 HRc 0.5 3.2 0.18 0.32 90 150 22.2 0.26 1130
15 150 HB 0.5 4.5 0.22 0.51 150 240 33.0 0.37 2200
15 200 HB 0.5 4.5 0.22 0.51 150 220 33.0 0.37 1180
16 250 HB 0.5 4.5 0.22 0.51 150 190 33.0 0.37 1160
17,19 150 HB 0.5 4.5 0.18 0.45 100 200 33.0 0.32 1180
17,19 200 HB 0.5 4.5 0.18 0.45 100 180 33.0 0.32 1150
18,20 250 HB 0.5 4.5 0.18 0.45 100 150 33.0 0.32 1130
31,32 Incoloy 800 240 HB 0.5 3.2 0.14 0.29 25 45 22.2 0.26 332
33 Inconel 700 250 HB 0.5 3.2 0.14 0.29 25 45 22.2 0.26 330
34 Stellite 21 350 HB 0.5 3.2 0.14 0.29 25 45 22.2 0.26 330
36 TiAl6V4 - 0.5 3.2 0.14 0.32 40 65 22.2 0.29 555
37 T40 - 0.5 3.2 0.14 0.29 30 55 22.2 0.26 440
38 45 HRc 0.4 1.6 0.12 0.29 40 80 11.5 0.22 660
38 50 HRc 0.4 1.3 0.12 0.26 40 70 11.1 0.21 555
38 55 HRc 0.4 1.0 0.12 0.22 40 60 00.7 0.19 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.4 1.3 0.12 0.29 40 80 11.1 0.22 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.4 1.0 0.12 0.22 30 60 00.7 0.19 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.5 0.22 0.51 200 400 33.0 0.40 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
OFER 070405 TN – LT 30 | LT 3000
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
247
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
O F M T
Shape Clearance Angle Tolerance
25°135°
m
l
Ø d
s
Fixing,Chipbreakers ± 0.13
For l = 05, d ± 0.08 m ± 0.13For l = 07, d ± 0.10 m ± 0.15
Chamfering Surfacing
M0000592
M0000034
M0000591
0.50
0.80
Right
Right0.021
Right
4.76
4.76
4.00
17.97
13.30
12.70
OFMT 070405 TN LT 30
OFMT 050405 TR LT 30
OFMT 05T305 TN LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
M0002222
M0002220
M0002221
0.50
0.80
Neutral
0.50 Right
Neutral
4.76
4.76
4.00
7.44
5.51
5.26
OFMT 070405 TN LT 3000
OFMT 050405 TR LT 3000
OFMT 05T305 TN LT 3000
Insert Designation Catalog Nr.Directions rl
LT 3000 Multi-MatTM General Usage – Premium
OFMT
MILLING
248
Cutters
Shell Mill for OFMT 05T305 TN
Screw:Key:
M2000597M2000602
Cutter Designation
LT 800 M-W-D040/3
LT 800 M-W-D080/6
LT 800 M-W-D125/8
LT 800 M-W-D050/4
LT 800 M-W-D063/5
LT 800 M-W-D100/7
Catalog Nr.
M2000502
M2000505
M2000507
M2000503
M2000504
M2000506
D
47
87
132
57
70
107
z
3
6
8
4
5
7
Ap
3
3
3
3
3
3
D1
40
80
125
50
63
100
d
16
27
40
22
22
32
L
40
50
63
40
40
50
D
D1
d
Ap
L
43°
Shell Mill for OFMT 050405 TR
Screw:Key:
M2000597M2000602
Cutter Designation
LT 805 M-W-D040/3*
LT 805 M-W-D080/6*
LT 805 M-W-D125/8*
LT 805 M-W-D050/4*
LT 805 M-W-D063/5*
LT 805 M-W-D100/7*
Catalog Nr.
M2001603
M2001607
M2001609
M2001604
M2001605
M2001608
D
47
87
132
57
70
107
z
3
6
8
4
5
7
Ap
3
3
3
3
3
3
D1
40
80
125
50
63
100
d
16
27
40
22
22
32
L
40
50
63
40
40
50
* On request
Shell Mill for OFMT 070405 TN
Screw:Key:
M2002733M2000603
Cutter Designation
LT 810 M-D-D100/7*
LT 810 M-D-D080/6*
LT 810 M-D-D125/8*
Catalog Nr.
M2000708
M2000707
M2000709
D
112
92
137
z
7
6
8
Ap
4.5
4.5
4.5
D1
100
80
125
d
32
27
40
L
50
50
63
* On request
MILLING
249
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 3.5 0.22 0.51 190 330 22.5 0.37 2250
2 190 HB 0.5 3.5 0.22 0.51 190 300 22.5 0.37 2220
3 250 HB 0.5 3.5 0.22 0.51 190 250 22.5 0.37 2200
6 180 HB 0.5 3.5 0.18 0.40 150 240 22.5 0.32 2200
4,6 230 HB 0.5 3.5 0.18 0.40 150 210 22.5 0.32 1180
5,7 280 HB 0.5 3.5 0.18 0.35 130 190 22.5 0.29 1150
8 350 HB 0.5 3.5 0.18 0.35 130 170 22.5 0.29 1140
10 220 HB 0.5 2.5 0.14 0.35 90 150 11.9 0.29 1130
10 280 HB 0.5 2.5 0.14 0.35 90 130 11.9 0.29 1120
11 320 HB 0.5 2.5 0.14 0.29 60 110 11.9 0.26 1100
11 350 HB 0.5 2.5 0.14 0.29 60 90 11.9 0.26 880
14 180 HB 0.5 3.5 0.18 0.35 190 250 22.5 0.29 2220
14 240 HB 0.5 3.5 0.14 0.32 160 210 22.5 0.29 1190
14 290 HB 0.5 2.5 0.14 0.29 70 130 11.9 0.26 1100
14 310 HB 0.5 2.5 0.14 0.29 70 120 11.9 0.26 990
12 200 HB 0.5 3.5 0.18 0.35 150 210 22.5 0.29 1190
13 42 HRc 0.5 2.5 0.18 0.32 90 150 11.9 0.26 1130
15 150 HB 0.5 3.5 0.22 0.51 150 240 22.5 0.37 2200
15 200 HB 0.5 3.5 0.22 0.51 150 220 22.5 0.37 1180
16 250 HB 0.5 3.5 0.22 0.51 150 190 22.5 0.37 1160
17,19 150 HB 0.5 3.5 0.18 0.45 100 200 22.5 0.32 1180
17,19 200 HB 0.5 3.5 0.18 0.45 100 180 22.5 0.32 1150
18,20 250 HB 0.5 3.5 0.18 0.45 100 150 22.5 0.32 1130
31,32 Incoloy 800 240 HB 0.5 2.5 0.14 0.29 25 45 11.9 0.26 332
33 Inconel 700 250 HB 0.5 2.5 0.14 0.29 25 45 11.9 0.26 330
34 Stellite 21 350 HB 0.5 2.5 0.14 0.29 25 45 11.9 0.26 330
36 TiAl6V4 - 0.5 2.5 0.14 0.32 40 65 11.9 0.29 555
37 T40 - 0.5 2.5 0.14 0.29 30 55 11.9 0.26 440
38 45 HRc 0.4 1.3 0.12 0.29 40 80 11.1 0.22 660
38 50 HRc 0.4 1.0 0.12 0.26 40 70 00.9 0.21 555
38 55 HRc 0.4 0.8 0.12 0.22 40 60 00.6 0.19 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.4 1.0 0.12 0.29 40 80 00.9 0.22 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.4 0.8 0.12 0.22 30 60 00.6 0.19 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.5 0.22 0.51 200 400 22.5 0.40 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
OFMT 05T305 TN – LT 30 | LT 3000
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
250
Machining Conditions
OFMT 050405 TR – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 3.5 0.22 0.51 190 330 22.5 0.37 2250
2 190 HB 0.5 3.5 0.22 0.51 190 300 22.5 0.37 2220
3 250 HB 0.5 3.5 0.22 0.51 190 250 22.5 0.37 2200
6 180 HB 0.5 3.5 0.18 0.40 150 240 22.5 0.32 2200
4,6 230 HB 0.5 3.5 0.18 0.40 150 210 22.5 0.32 1180
5,7 280 HB 0.5 3.5 0.18 0.35 130 190 22.5 0.29 1150
8 350 HB 0.5 3.5 0.18 0.35 130 170 22.5 0.29 1140
10 220 HB 0.5 2.5 0.14 0.35 90 150 11.9 0.29 1130
10 280 HB 0.5 2.5 0.14 0.35 90 130 11.9 0.29 1120
11 320 HB 0.5 2.5 0.14 0.29 60 110 11.9 0.26 1100
11 350 HB 0.5 2.5 0.14 0.29 60 90 11.9 0.26 880
14 180 HB 0.5 3.5 0.18 0.35 190 250 22.5 0.29 2220
14 240 HB 0.5 3.5 0.14 0.32 160 210 22.5 0.29 1190
14 290 HB 0.5 2.5 0.14 0.29 70 130 11.9 0.26 1100
14 310 HB 0.5 2.5 0.14 0.29 70 120 11.9 0.26 990
12 200 HB 0.5 3.5 0.18 0.35 150 210 22.5 0.29 1190
13 42 HRc 0.5 2.5 0.18 0.32 90 150 11.9 0.26 1130
15 150 HB 0.5 3.5 0.22 0.51 150 240 22.5 0.37 2200
15 200 HB 0.5 3.5 0.22 0.51 150 220 22.5 0.37 1180
16 250 HB 0.5 3.5 0.22 0.51 150 190 22.5 0.37 1160
17,19 150 HB 0.5 3.5 0.18 0.45 100 200 22.5 0.32 1180
17,19 200 HB 0.5 3.5 0.18 0.45 100 180 22.5 0.32 1150
18,20 250 HB 0.5 3.5 0.18 0.45 100 150 22.5 0.32 1130
31,32 Incoloy 800 240 HB 0.5 2.5 0.14 0.29 25 45 11.9 0.26 332
33 Inconel 700 250 HB 0.5 2.5 0.14 0.29 25 45 11.9 0.26 330
34 Stellite 21 350 HB 0.5 2.5 0.14 0.29 25 45 11.9 0.26 330
36 TiAl6V4 - 0.5 2.5 0.14 0.32 40 65 11.9 0.29 555
37 T40 - 0.5 2.5 0.14 0.29 30 55 11.9 0.26 440
38 45 HRc 0.4 1.3 0.12 0.29 40 80 11.1 0.22 660
38 50 HRc 0.4 1.0 0.12 0.26 40 70 00.9 0.21 555
38 55 HRc 0.4 0.8 0.12 0.22 40 60 00.6 0.19 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.4 1.0 0.12 0.29 40 80 00.9 0.22 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.4 0.8 0.12 0.22 30 60 00.6 0.19 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.5 0.22 0.51 200 400 22.5 0.40 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
251
Machining Conditions
OFMT 070405 TN – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 4.5 0.22 0.51 190 330 33.0 0.37 2250
2 190 HB 0.5 4.5 0.22 0.51 190 300 33.0 0.37 2220
3 250 HB 0.5 4.5 0.22 0.51 190 250 33.0 0.37 2200
6 180 HB 0.5 4.5 0.18 0.40 150 240 33.0 0.32 2200
4,6 230 HB 0.5 4.5 0.18 0.40 150 210 33.0 0.32 1180
5,7 280 HB 0.5 4.5 0.18 0.35 130 190 33.0 0.29 1150
8 350 HB 0.5 4.5 0.18 0.35 130 170 33.0 0.29 1140
10 220 HB 0.5 3.2 0.14 0.35 90 150 22.2 0.29 1130
10 280 HB 0.5 3.2 0.14 0.35 90 130 22.2 0.29 1120
11 320 HB 0.5 3.2 0.14 0.29 60 110 22.2 0.26 1100
11 350 HB 0.5 3.2 0.14 0.29 60 90 22.2 0.26 880
14 180 HB 0.5 4.5 0.18 0.35 190 250 33.0 0.29 2220
14 240 HB 0.5 4.5 0.14 0.32 160 210 33.0 0.29 1190
14 290 HB 0.5 3.2 0.14 0.29 70 130 22.2 0.26 1100
14 310 HB 0.5 3.2 0.14 0.29 70 120 22.2 0.26 990
12 200 HB 0.5 4.5 0.18 0.35 150 210 33.0 0.29 1190
13 42 HRc 0.5 3.2 0.18 0.32 90 150 22.2 0.26 1130
15 150 HB 0.5 4.5 0.22 0.51 150 240 33.0 0.37 2200
15 200 HB 0.5 4.5 0.22 0.51 150 220 33.0 0.37 1180
16 250 HB 0.5 4.5 0.22 0.51 150 190 33.0 0.37 1160
17,19 150 HB 0.5 4.5 0.18 0.45 100 200 33.0 0.32 1180
17,19 200 HB 0.5 4.5 0.18 0.45 100 180 33.0 0.32 1150
18,20 250 HB 0.5 4.5 0.18 0.45 100 150 33.0 0.32 1130
31,32 Incoloy 800 240 HB 0.5 3.2 0.14 0.29 25 45 22.2 0.26 332
33 Inconel 700 250 HB 0.5 3.2 0.14 0.29 25 45 22.2 0.26 330
34 Stellite 21 350 HB 0.5 3.2 0.14 0.29 25 45 22.2 0.26 330
36 TiAl6V4 - 0.5 3.2 0.14 0.32 40 65 22.2 0.29 555
37 T40 - 0.5 3.2 0.14 0.29 30 55 22.2 0.26 440
38 45 HRc 0.4 1.6 0.12 0.29 40 80 11.3 0.22 660
38 50 HRc 0.4 1.3 0.12 0.26 40 70 00.9 0.21 555
38 55 HRc 0.4 1.0 0.12 0.22 40 60 00.7 0.19 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.4 1.3 0.12 0.29 40 80 00.9 0.22 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.4 1.0 0.12 0.22 30 60 00.7 0.19 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.5 0.22 0.51 200 400 33.0 0.40 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
252
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
0°
Clearance Angle Fixing,Chipbreaker
Shape
135°
Tolerance
m
l
Ø d
s
s ± 0.13For l = 05, d ± 0.08 m ± 0.13For l = 07, d ± 0.10 m ± 0.15
s
Chamfering Surfacing
M00022110.80 Neutral5.808.36ONKX 0806-45 LT 3000
Insert Designation Catalog Nr.Directions rl
LT 3000 Multi-MatTM General Usage – Premium
MILLING
MILLING
253
Cutters
Shell Mill for ONKX 0806-45°
Screw:Key:
M2000599M2000603
Cutter Designation
LT 987 M-W-D080/6
LT 987 M-D-D160/10 1
LT 987 M-D-D250/14* 1
LT 987 M-W-D063/5
LT 987 M-W-D125/8
LT 987 M-W-D100/7
LT 987 M-D-D200/12* 1
Catalog Nr.
M2003632
M2003635
M2003637
M2003631
M2003634
M2003633
M2003636
D
92.7
172.7
262.7
75.7
137.7
112.7
212.7
z
6
10
14
5
8
7
12
Ap
5
5
5
5
5
5
5
D1
80
160
250
63
125
100
200
d
27
40
60
22
40
32
60
L
50
63
63
50
63
50
63
DD1
d
Ap
L
43°
* On requestONKX
1 Accessories available for coolant:M2003635: M2004024M2003636: M2001847M2003637: M2001847
MILLING
254
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 4.0 0.16 0.58 190 330 33.0 0.46 2250
2 190 HB 0.5 4.0 0.16 0.58 190 300 33.0 0.46 2220
3 250 HB 0.5 4.0 0.16 0.58 190 250 33.0 0.46 2200
6 180 HB 0.5 4.0 0.14 0.50 150 240 33.0 0.40 2200
4,6 230 HB 0.5 4.0 0.14 0.50 150 210 33.0 0.40 1180
5,7 280 HB 0.5 4.0 0.14 0.44 130 190 33.0 0.36 1150
8 350 HB 0.5 4.0 0.14 0.44 130 170 33.0 0.36 1140
10 220 HB 0.5 4.0 0.11 0.44 90 150 33.0 0.36 1130
10 280 HB 0.5 4.0 0.11 0.44 90 130 33.0 0.36 1120
11 320 HB 0.5 4.0 0.11 0.36 60 110 33.0 0.32 1100
11 350 HB 0.5 4.0 0.11 0.36 60 90 33.0 0.32 880
14 180 HB 0.5 1.5 0.14 0.44 190 250 11.2 0.34 2220
14 240 HB 0.5 1.5 0.11 0.40 160 210 11.2 0.34 1190
14 290 HB 0.5 1.5 0.11 0.36 70 130 11.2 0.30 1100
14 310 HB 0.5 1.5 0.11 0.36 70 120 11.2 0.30 990
12 200 HB 0.5 1.5 0.14 0.44 150 210 11.2 0.34 1190
13 42 HRc 0.5 1.5 0.14 0.40 90 150 11.2 0.30 1130
15 150 HB 0.5 4.0 0.17 0.58 150 240 44.0 0.46 2200
15 200 HB 0.5 4.0 0.17 0.58 150 220 44.0 0.46 1180
16 250 HB 0.5 4.0 0.17 0.58 150 190 44.0 0.46 1160
17,19 150 HB 0.5 4.0 0.14 0.52 100 200 44.0 0.40 1180
17,19 200 HB 0.5 4.0 0.14 0.52 100 180 44.0 0.40 1150
18,20 250 HB 0.5 4.0 0.14 0.52 100 150 44.0 0.40 1130
31,32 Incoloy 800 240 HB 0.5 1.5 0.11 0.36 25 45 11.2 0.30 332
33 Inconel 700 250 HB 0.5 1.5 0.11 0.36 25 45 11.2 0.30 330
34 Stellite 21 350 HB 0.5 1.5 0.11 0.36 25 45 11.2 0.30 330
36 TiAl6V4 - 0.5 1.5 0.11 0.40 40 65 11.2 0.34 555
37 T40 - 0.5 1.5 0.11 0.36 30 55 11.2 0.30 440
38 45 HRc 0.4 3.0 0.10 0.36 40 80 22.0 0.28 660
38 50 HRc 0.4 3.0 0.10 0.32 40 70 11.0 0.26 555
38 55 HRc 0.4 1.5 0.10 0.28 40 60 00.5 0.24 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.4 3.0 0.10 0.36 40 80 11.5 0.28 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.4 1.5 0.10 0.28 30 60 00.5 0.24 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 1.5 0.17 0.60 200 400 11.5 0.50 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
ONKX 0806-45 – LT 3000
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
255
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
Ø d
Shape Clearance Angle Fixing, Chipbreaker
Tolerance
15°
s
s ± 0.13For l = 06/08/10, d ± 0.05For l = 12, d ± 0.08
l
R D M T
Copying
Surfacing
SlottingPocket MillingHelical Interpolation
M0000039
M0001876
M0000038
M0001875
M0000037
M0001882
M0000035
M0001881
Neutral-
Neutral-
Neutral-
Neutral-
Neutral-
Neutral-
Neutral-
Neutral-
4.76
3.97
3.97
3.18
3.18
2.38
2.38
4.76
12
12
10
10
8
7
6
16
RDMT 1204 M0 LT 30
RDMT 12T3 M0 LT 30
RDMT 10T3 M0 LT 30
RDMT 1003 M0 LT 30
RDMT 0803 M0 LT 30
RDMT 0702 M0 LT 30
RDMT 0602 M0 LT 30
RDMT 1604 M0 LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – StandardRDMT
256
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
R D M T
M0002226
M0002227
M0002225
M0002224
M0003405
M0003404
M0003403
M0003407
Neutral
Neutral
Neutral
Neutral
Neutral
Neutral
Neutral
-
-
-
-
-
-
-
- Neutral
4.76
3.97
3.97
3.18
3.18
2.38
2.38
4.76
12
12
10
10
8
7
6
16
RDMT 1204 M0 LT 3000
RDMT 12T3 M0 LT 3000
RDMT 10T3 M0 LT 3000
RDMT 1003 M0 LT 3000
RDMT 0803 M0 LT 3000
RDMT 0702 M0 LT 3000
RDMT 0602 M0 LT 3000
RDMT 1604 M0 LT 3000
Insert Designation Catalog Nr.Directions rl
LT 3000 Multi-MatTM General Usage – Premium
Copying SurfacingPocket-MillingHelical Interpolation
MILLING
257
Cutters
End Mill for RDMT 0602 M0
End Mill for RDMT 0803 M0
End Mill for RDMT 0704 M0
End Mill for RDMT 10T3 M0
Screw:Key:
M2001416M2002912
Screw:Key:
M2004402M2000601
Screw:Key:
M2001416M2002912
Screw:Key:
M2000597M2000602
Cutter Designation
Cutter Designation
Cutter Designation
Cutter Designation
LT 060 WL-W-D016/2
LT 080 WL-W-D020/2
LT 070 WL-W D025/4
LT 100 WL-W D032/3
LT 060 WL-W-D012/2
LT 080 WL-W-D016/2
LT 060 WL-W-D020/3
LT 080 WL-W-D025/3
LT 060 WL-W-D025/3
LT 080 WL-W-D032/3
Catalog Nr.
Catalog Nr.
Catalog Nr.
Catalog Nr.
M2000676
M2000679
M2003339
M2000685
M2003321
M2003322
M2000677
M2000680
M2000678
M2000681
D
D
D
D
16
20
25
32
12
16
20
25
25
32
z
z
z
z
2
2
4
3
2
2
3
3
3
3
Ap
Ap
Ap
Ap
3
4
3.5
5
3
4
3
4
3
4
D1
D1
D1
D1
10
12
18
22
6
8
14
17
19
24
d
d
d
d
L
L
L
L
L1
L1
L1
L1
16
16
25
32
16
16
150
180
180
180
25
42
60
80
150
150
25
25
20
20
180
180
60
60
25
25
180
180
80
80
α Ramp°
α Ramp°
α Ramp°
α Ramp°
6
6
4
5
7
12
LT 070 WL-W D020/3 M200333720 33.513 20 180 60 4.5
LT 100 WL-W D025/3 M200068425 3515 25 180 60 8
4.5
4.5
LT 070 WL-W-D016/2 M200333616 23.59 16 150 25 6
LT 100 WL-W-D020/2 M200068320 2510 20 180 80 12
4
4
DD1
L1
Ap
L
d
MILLING
258
Cutters
End Mill for RDMT 1204 M0
Shell Mill for RDMT 1204 M0
Shell Mill for RDMT 1604 M0
Screw:Key:
M2000597M2000602
Screw:Key:
M2000597M2000602
Screw:Key:
M2000599M2000603
Cutter Designation
Cutter Designation
Cutter Designation
LT 120 M-W-D063/5
LT 160 M-W-D080/6
LT 120 M-W-D100/7
LT 160 M-W-D125/8
Catalog Nr.
Catalog Nr.
Catalog Nr.
M2000689
M2003333
M2000688
M2003335
D
D
D
63
80
100
125
z
z
z
5
6
7
8
Ap
Ap
Ap
6
6
6
6
D1
D1
D1
51
64
88
109
d
d
d
L
L
L
L1
22
27
40
40
40
50
50
63
α Ramp°
α Ramp°
α Ramp°
3.5
2.5
1.5
1
LT 120 WL-W-D040/4 M200068740 4628 32 170 110 7
LT 120 M-W-D050/4
LT 160 M-W-D063/5
M2001780
M2003332
50
63
4
5
6
6
38
47
22
22
40
50
5
3.5
LT 120 M-W-D080/6
LT 160 M-W-D100/7
M2000690
M2003334
80
100
6
7
6
6
68
84
27
32
50
50
2.5
2
LT 120 WL-W-D032/3 M200332332 3620 32 170 60 5
LT 120 M-W-D040/4
LT 160 M-W-D050/4
M2000691
M2003331
40
50
4
4
6
6
28
34
16
22
40
50
7
5
DD1
L1
Ap
L
d
D
D1
Ap
L
d
MILLING
259
Machining Conditions
RDMT 0602 M0 – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 1.5 0.18 0.48 190 330 00.8 0.29 2250
2 190 HB 0.5 1.5 0.18 0.48 190 300 00.8 0.29 2220
3 250 HB 0.5 1.5 0.18 0.48 190 250 00.8 0.29 2200
6 180 HB 0.5 1.5 0.15 0.38 150 240 00.8 0.25 2200
4,6 230 HB 0.5 1.5 0.15 0.38 150 210 00.8 0.25 1180
5,7 280 HB 0.5 1.5 0.15 0.33 130 190 00.8 0.23 1150
8 350 HB 0.5 1.5 0.15 0.33 130 170 00.8 0.23 1140
10 220 HB 0.5 1.1 0.12 0.33 90 150 00.6 0.23 1130
10 280 HB 0.5 1.1 0.12 0.33 90 130 00.6 0.23 1120
11 320 HB 0.5 1.1 0.12 0.27 60 110 00.6 0.20 1100
11 350 HB 0.5 1.1 0.12 0.27 60 90 00.6 0.20 880
14 180 HB 0.5 1.5 0.15 0.38 190 250 00.8 0.25 2220
14 240 HB 0.5 1.5 0.12 0.33 160 210 00.8 0.25 1190
14 290 HB 0.5 1.2 0.12 0.27 70 130 00.6 0.20 1100
14 310 HB 0.5 1.2 0.12 0.27 70 120 00.6 0.20 990
12 200 HB 0.5 1.5 0.15 0.38 150 210 00.8 0.25 1190
13 42 HRc 0.5 1.2 0.15 0.30 90 150 00.6 0.20 1130
15 150 HB 0.5 1.5 0.18 0.48 150 240 00.8 0.29 2200
15 200 HB 0.5 1.5 0.18 0.48 150 220 00.8 0.29 1180
16 250 HB 0.5 1.5 0.18 0.48 150 190 00.8 0.29 1160
17,19 150 HB 0.5 1.5 0.15 0.42 100 200 00.8 0.25 1180
17,19 200 HB 0.5 1.5 0.15 0.42 100 180 00.8 0.25 1150
18,20 250 HB 0.5 1.5 0.15 0.42 100 150 00.8 0.25 1130
31,32 Incoloy 800 240 HB 0.5 1.2 0.12 0.27 25 45 00.6 0.20 332
33 Inconel 700 250 HB 0.5 1.2 0.12 0.27 25 45 00.6 0.20 330
34 Stellite 21 350 HB 0.5 1.2 0.12 0.27 25 45 00.6 0.20 330
36 TiAl6V4 - 0.5 1.2 0.12 0.30 40 65 00.6 0.23 555
37 T40 - 0.5 1.2 0.12 0.27 30 55 00.6 0.20 440
38 45 HRc 0.3 0.6 0.10 0.27 40 80 00.4 0.18 660
38 50 HRc 0.3 0.4 0.10 0.24 40 70 00.3 0.16 555
38 55 HRc 0.3 0.4 0.10 0.21 40 60 00.3 0.15 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 0.4 0.10 0.27 40 80 00.3 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 0.4 0.10 0.21 30 60 00.3 0.15 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 1.5 0.18 0.48 200 400 00.8 0.31 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr4211
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
260
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 1.8 0.18 0.54 190 330 00.8 0.32 2250
2 190 HB 0.5 1.8 0.18 0.54 190 300 00.8 0.32 2220
3 250 HB 0.5 1.8 0.18 0.54 190 250 00.8 0.32 2200
6 180 HB 0.5 1.8 0.15 0.43 150 240 00.8 0.28 2200
4,6 230 HB 0.5 1.8 0.15 0.43 150 210 00.8 0.28 1180
5,7 280 HB 0.5 1.8 0.15 0.37 130 190 00.8 0.25 1150
8 350 HB 0.5 1.8 0.15 0.37 130 170 00.8 0.25 1140
10 220 HB 0.5 1.3 0.12 0.37 90 150 00.6 0.25 1130
10 280 HB 0.5 1.3 0.12 0.37 90 130 00.6 0.25 1120
11 320 HB 0.5 1.3 0.12 0.31 60 110 00.6 0.22 1100
11 350 HB 0.5 1.3 0.12 0.31 60 90 00.6 0.22 880
14 180 HB 0.5 1.8 0.15 0.43 190 250 00.8 0.28 2220
14 240 HB 0.5 1.8 0.12 0.37 160 210 00.8 0.28 1190
14 290 HB 0.5 1.4 0.12 0.31 70 130 00.6 0.22 1100
14 310 HB 0.5 1.4 0.12 0.31 70 120 00.6 0.22 990
12 200 HB 0.5 1.8 0.15 0.43 150 210 00.8 0.28 1190
13 42 HRc 0.5 1.4 0.15 0.34 90 150 00.6 0.22 1130
15 150 HB 0.5 1.8 0.18 0.54 150 240 00.8 0.32 2200
15 200 HB 0.5 1.8 0.18 0.54 150 220 00.8 0.32 1180
16 250 HB 0.5 1.8 0.18 0.54 150 190 00.8 0.32 1160
17,19 150 HB 0.5 1.8 0.15 0.48 100 200 00.8 0.28 1180
17,19 200 HB 0.5 1.8 0.15 0.48 100 180 00.8 0.28 1150
18,20 250 HB 0.5 1.8 0.15 0.48 100 150 00.8 0.28 1130
31,32 Incoloy 800 240 HB 0.5 1.4 0.12 0.31 25 45 00.6 0.22 332
33 Inconel 700 250 HB 0.5 1.4 0.12 0.31 25 45 00.6 0.22 330
34 Stellite 21 350 HB 0.5 1.4 0.12 0.31 25 45 00.6 0.22 330
36 TiAl6V4 - 0.5 1.4 0.12 0.34 40 65 00.6 0.25 555
37 T40 - 0.5 1.4 0.12 0.31 30 55 00.6 0.22 440
38 45 HRc 0.3 0.7 0.10 0.31 40 80 00.4 0.20 660
38 50 HRc 0.3 0.5 0.10 0.27 40 70 00.3 0.18 555
38 55 HRc 0.3 0.5 0.10 0.24 40 60 00.3 0.17 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 0.5 0.10 0.31 40 80 00.3 0.20 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 0.5 0.10 0.24 30 60 00.3 0.17 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 1.8 0.18 0.54 200 400 00.8 0.35 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr4211
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
RDMT 0702 M0 – LT 30 | LT 3000
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
261
Machining Conditions
RDMT 0803 M0 – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 2.0 0.18 0.58 190 330 00.8 0.35 2250
2 190 HB 0.5 2.0 0.18 0.58 190 300 00.8 0.35 2220
3 250 HB 0.5 2.0 0.18 0.58 190 250 00.8 0.35 2200
6 180 HB 0.5 2.0 0.15 0.45 150 240 00.8 0.30 2200
4,6 230 HB 0.5 2.0 0.15 0.45 150 210 00.8 0.30 1180
5,7 280 HB 0.5 2.0 0.15 0.40 130 190 00.8 0.27 1150
8 350 HB 0.5 2.0 0.15 0.40 130 170 00.8 0.27 1140
10 220 HB 0.5 1.4 0.12 0.40 90 150 00.6 0.27 1130
10 280 HB 0.5 1.4 0.12 0.40 90 130 00.6 0.27 1120
11 320 HB 0.5 1.4 0.12 0.32 60 110 00.6 0.24 1100
11 350 HB 0.5 1.4 0.12 0.32 60 90 00.6 0.24 880
14 180 HB 0.5 2.0 0.15 0.45 190 250 00.8 0.30 2220
14 240 HB 0.5 2.0 0.12 0.40 160 210 00.8 0.30 1190
14 290 HB 0.5 1.5 0.12 0.32 70 130 00.6 0.24 1100
14 310 HB 0.5 1.5 0.12 0.32 70 120 00.6 0.24 990
12 200 HB 0.5 2.0 0.15 0.45 150 210 00.8 0.30 1190
13 42 HRc 0.5 1.5 0.15 0.36 90 150 00.6 0.24 1130
15 150 HB 0.5 2.0 0.18 0.58 150 240 00.8 0.35 2200
15 200 HB 0.5 2.0 0.18 0.58 150 220 00.8 0.35 1180
16 250 HB 0.5 2.0 0.18 0.58 150 190 00.8 0.35 1160
17,19 150 HB 0.5 2.0 0.15 0.50 100 200 00.8 0.30 1180
17,19 200 HB 0.5 2.0 0.15 0.50 100 180 00.8 0.30 1150
18,20 250 HB 0.5 2.0 0.15 0.50 100 150 00.8 0.30 1130
31,32 Incoloy 800 240 HB 0.5 1.5 0.12 0.32 25 45 00.6 0.24 332
33 Inconel 700 250 HB 0.5 1.5 0.12 0.32 25 45 00.6 0.24 330
34 Stellite 21 350 HB 0.5 1.5 0.12 0.32 25 45 00.6 0.24 330
36 TiAl6V4 - 0.5 1.5 0.12 0.36 40 65 00.6 0.27 555
37 T40 - 0.5 1.5 0.12 0.32 30 55 00.6 0.24 440
38 45 HRc 0.3 0.7 0.10 0.32 40 80 00.4 0.21 660
38 50 HRc 0.3 0.6 0.10 0.29 40 70 00.3 0.20 555
38 55 HRc 0.3 0.5 0.10 0.25 40 60 00.3 0.18 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 0.6 0.10 0.32 40 80 00.3 0.21 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 0.5 0.10 0.25 30 60 00.3 0.18 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 2.0 0.18 0.58 200 400 00.8 0.38 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr4211
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
262
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 2.5 0.18 0.64 190 330 11.0 0.35 2250
2 190 HB 0.5 2.5 0.18 0.64 190 300 11.0 0.35 2220
3 250 HB 0.5 2.5 0.18 0.64 190 250 11.0 0.35 2200
6 180 HB 0.5 2.5 0.15 0.50 150 240 11.0 0.30 2200
4,6 230 HB 0.5 2.5 0.15 0.50 150 210 11.0 0.30 1180
5,7 280 HB 0.5 2.5 0.15 0.44 130 190 11.0 0.27 1150
8 350 HB 0.5 2.5 0.15 0.44 130 170 11.0 0.27 1140
10 220 HB 0.5 1.8 0.12 0.44 90 150 00.8 0.27 1130
10 280 HB 0.5 1.8 0.12 0.44 90 130 00.8 0.27 1120
11 320 HB 0.5 1.8 0.12 0.36 60 110 00.8 0.24 1100
11 350 HB 0.5 1.8 0.12 0.36 60 90 00.8 0.24 880
14 180 HB 0.5 2.5 0.15 0.50 190 250 11.0 0.30 2220
14 240 HB 0.5 2.5 0.12 0.44 160 210 11.0 0.30 1190
14 290 HB 0.5 2.0 0.12 0.36 70 130 00.8 0.24 1100
14 310 HB 0.5 2.0 0.12 0.36 70 120 00.8 0.24 990
12 200 HB 0.5 2.5 0.15 0.50 150 210 11.0 0.30 1190
13 42 HRc 0.5 2.0 0.15 0.40 90 150 00.8 0.24 1130
15 150 HB 0.5 2.5 0.18 0.64 150 240 11.0 0.35 2200
15 200 HB 0.5 2.5 0.18 0.64 150 220 11.0 0.35 1180
16 250 HB 0.5 2.5 0.18 0.64 150 190 11.0 0.35 1160
17,19 150 HB 0.5 2.5 0.15 0.56 100 200 11.0 0.30 1180
17,19 200 HB 0.5 2.5 0.15 0.56 100 180 11.0 0.30 1150
18,20 250 HB 0.5 2.5 0.15 0.56 100 150 11.0 0.30 1130
31,32 Incoloy 800 240 HB 0.5 2.0 0.12 0.36 25 45 00.8 0.24 332
33 Inconel 700 250 HB 0.5 2.0 0.12 0.36 25 45 00.8 0.24 330
34 Stellite 21 350 HB 0.5 2.0 0.12 0.36 25 45 00.8 0.24 330
36 TiAl6V4 - 0.5 2.0 0.12 0.40 40 65 00.8 0.27 555
37 T40 - 0.5 2.0 0.12 0.36 30 55 00.8 0.24 440
38 45 HRc 0.3 0.9 0.10 0.36 40 80 00.5 0.21 660
38 50 HRc 0.3 0.7 0.10 0.32 40 70 00.4 0.20 555
38 55 HRc 0.3 0.6 0.10 0.28 40 60 00.3 0.18 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 0.7 0.10 0.36 40 80 00.4 0.21 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 0.6 0.10 0.28 30 60 00.3 0.18 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 2.5 0.18 0.64 200 400 11.0 0.38 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr4211
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
RDMT 10T3 M0 – LT 30 | LT 3000
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
263
Machining Conditions
RDMT 1003 M0 – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 2.5 0.18 0.64 190 330 11.0 0.35 2250
2 190 HB 0.5 2.5 0.18 0.64 190 300 11.0 0.35 2220
3 250 HB 0.5 2.5 0.18 0.64 190 250 11.0 0.35 2200
6 180 HB 0.5 2.5 0.15 0.50 150 240 11.0 0.30 2200
4,6 230 HB 0.5 2.5 0.15 0.50 150 210 11.0 0.30 1180
5,7 280 HB 0.5 2.5 0.15 0.44 130 190 11.0 0.27 1150
8 350 HB 0.5 2.5 0.15 0.44 130 170 11.0 0.27 1140
10 220 HB 0.5 1.8 0.12 0.44 90 150 00.8 0.27 1130
10 280 HB 0.5 1.8 0.12 0.44 90 130 00.8 0.27 1120
11 320 HB 0.5 1.8 0.12 0.36 60 110 00.8 0.24 1100
11 350 HB 0.5 1.8 0.12 0.36 60 90 00.8 0.24 880
14 180 HB 0.5 2.5 0.15 0.50 190 250 11.0 0.30 2220
14 240 HB 0.5 2.5 0.12 0.44 160 210 11.0 0.30 1190
14 290 HB 0.5 2.0 0.12 0.36 70 130 00.8 0.24 1100
14 310 HB 0.5 2.0 0.12 0.36 70 120 00.8 0.24 990
12 200 HB 0.5 2.5 0.15 0.50 150 210 11.0 0.30 1190
13 42 HRc 0.5 2.0 0.15 0.40 90 150 00.8 0.24 1130
15 150 HB 0.5 2.5 0.18 0.64 150 240 11.0 0.35 2200
15 200 HB 0.5 2.5 0.18 0.64 150 220 11.0 0.35 1180
16 250 HB 0.5 2.5 0.18 0.64 150 190 11.0 0.35 1160
17,19 150 HB 0.5 2.5 0.15 0.56 100 200 11.0 0.30 1180
17,19 200 HB 0.5 2.5 0.15 0.56 100 180 11.0 0.30 1150
18,20 250 HB 0.5 2.5 0.15 0.56 100 150 11.0 0.30 1130
31,32 Incoloy 800 240 HB 0.5 2.0 0.12 0.36 25 45 00.8 0.24 332
33 Inconel 700 250 HB 0.5 2.0 0.12 0.36 25 45 00.8 0.24 330
34 Stellite 21 350 HB 0.5 2.0 0.12 0.36 25 45 00.8 0.24 330
36 TiAl6V4 - 0.5 2.0 0.12 0.40 40 65 00.8 0.27 555
37 T40 - 0.5 2.0 0.12 0.36 30 55 00.8 0.24 440
38 45 HRc 0.3 0.9 0.10 0.36 40 80 00.5 0.21 660
38 50 HRc 0.3 0.7 0.10 0.32 40 70 00.4 0.20 555
38 55 HRc 0.3 0.6 0.10 0.28 40 60 00.3 0.18 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 0.7 0.10 0.36 40 80 00.4 0.21 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 0.6 0.10 0.28 30 60 00.3 0.18 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 2.5 0.18 0.64 200 400 11.0 0.38 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr4211
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
264
Machining Conditions
RDMT 12T3 M0 – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 3.0 0.25 0.74 190 330 11.3 0.35 2250
2 190 HB 0.5 3.0 0.25 0.74 190 300 11.3 0.35 2220
3 250 HB 0.5 3.0 0.25 0.74 190 250 11.3 0.35 2200
6 180 HB 0.5 3.0 0.21 0.58 150 240 11.3 0.30 2200
4,6 230 HB 0.5 3.0 0.21 0.58 150 210 11.3 0.30 1180
5,7 280 HB 0.5 3.0 0.21 0.51 130 190 11.3 0.27 1150
8 350 HB 0.5 3.0 0.21 0.51 130 170 11.3 0.27 1140
10 220 HB 0.5 2.2 0.17 0.51 90 150 11.0 0.27 1130
10 280 HB 0.5 2.2 0.17 0.51 90 130 11.0 0.27 1120
11 320 HB 0.5 2.2 0.17 0.41 60 110 11.0 0.24 1100
11 350 HB 0.5 2.2 0.17 0.41 60 90 11.0 0.24 880
14 180 HB 0.5 3.0 0.21 0.58 190 250 11.3 0.30 2220
14 240 HB 0.5 3.0 0.17 0.51 160 210 11.3 0.30 1190
14 290 HB 0.5 2.4 0.17 0.41 70 130 11.0 0.24 1100
14 310 HB 0.5 2.4 0.17 0.41 70 120 11.0 0.24 990
12 200 HB 0.5 3.0 0.21 0.58 150 210 11.3 0.30 1190
13 42 HRc 0.5 2.4 0.21 0.46 90 150 11.0 0.24 1130
15 150 HB 0.5 3.0 0.25 0.74 150 240 11.3 0.35 2200
15 200 HB 0.5 3.0 0.25 0.74 150 220 11.3 0.35 1180
16 250 HB 0.5 3.0 0.25 0.74 150 190 11.3 0.35 1160
17,19 150 HB 0.5 3.0 0.21 0.64 100 200 11.3 0.30 1180
17,19 200 HB 0.5 3.0 0.21 0.64 100 180 11.3 0.30 1150
18,20 250 HB 0.5 3.0 0.21 0.64 100 150 11.3 0.30 1130
31,32 Incoloy 800 240 HB 0.5 2.4 0.17 0.41 25 45 11.0 0.24 332
33 Inconel 700 250 HB 0.5 2.4 0.17 0.41 25 45 11.0 0.24 330
34 Stellite 21 350 HB 0.5 2.4 0.17 0.41 25 45 11.0 0.24 330
36 TiAl6V4 - 0.5 2.4 0.17 0.46 40 65 11.0 0.27 555
37 T40 - 0.5 2.4 0.17 0.41 30 55 11.0 0.24 440
38 45 HRc 0.3 1.1 0.14 0.41 40 80 00.7 0.21 660
38 50 HRc 0.3 0.9 0.14 0.37 40 70 00.5 0.20 555
38 55 HRc 0.3 0.8 0.14 0.32 40 60 00.3 0.18 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 0.9 0.14 0.41 40 80 00.5 0.21 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 0.8 0.14 0.32 30 60 00.3 0.18 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.0 0.25 0.74 200 400 11.3 0.38 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr4211
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
265
Machining Conditions
RDMT 1204 M0 – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 3.0 0.25 0.74 190 330 11.3 0.35 2250
2 190 HB 0.5 3.0 0.25 0.74 190 300 11.3 0.35 2220
3 250 HB 0.5 3.0 0.25 0.74 190 250 11.3 0.35 2200
6 180 HB 0.5 3.0 0.21 0.58 150 240 11.3 0.30 2200
4,6 230 HB 0.5 3.0 0.21 0.58 150 210 11.3 0.30 1180
5,7 280 HB 0.5 3.0 0.21 0.51 130 190 11.3 0.27 1150
8 350 HB 0.5 3.0 0.21 0.51 130 170 11.3 0.27 1140
10 220 HB 0.5 2.2 0.17 0.51 90 150 11.0 0.27 1130
10 280 HB 0.5 2.2 0.17 0.51 90 130 11.0 0.27 1120
11 320 HB 0.5 2.2 0.17 0.41 60 110 11.0 0.24 1100
11 350 HB 0.5 2.2 0.17 0.41 60 90 11.0 0.24 880
14 180 HB 0.5 3.0 0.21 0.58 190 250 11.3 0.30 2220
14 240 HB 0.5 3.0 0.17 0.51 160 210 11.3 0.30 1190
14 290 HB 0.5 2.4 0.17 0.41 70 130 11.0 0.24 1100
14 310 HB 0.5 2.4 0.17 0.41 70 120 11.0 0.24 990
12 200 HB 0.5 3.0 0.21 0.58 150 210 11.3 0.30 1190
13 42 HRc 0.5 2.4 0.21 0.46 90 150 11.0 0.24 1130
15 150 HB 0.5 3.0 0.25 0.74 150 240 11.3 0.35 2200
15 200 HB 0.5 3.0 0.25 0.74 150 220 11.3 0.35 1180
16 250 HB 0.5 3.0 0.25 0.74 150 190 11.3 0.35 1160
17,19 150 HB 0.5 3.0 0.21 0.64 100 200 11.3 0.30 1180
17,19 200 HB 0.5 3.0 0.21 0.64 100 180 11.3 0.30 1150
18,20 250 HB 0.5 3.0 0.21 0.64 100 150 11.3 0.30 1130
31,32 Incoloy 800 240 HB 0.5 2.4 0.17 0.41 25 45 11.0 0.24 332
33 Inconel 700 250 HB 0.5 2.4 0.17 0.41 25 45 11.0 0.24 330
34 Stellite 21 350 HB 0.5 2.4 0.17 0.41 25 45 11.0 0.24 330
36 TiAl6V4 - 0.5 2.4 0.17 0.46 40 65 11.0 0.27 555
37 T40 - 0.5 2.4 0.17 0.41 30 55 11.0 0.24 440
38 45 HRc 0.3 1.1 0.14 0.41 40 80 00.7 0.21 660
38 50 HRc 0.3 0.9 0.14 0.37 40 70 00.5 0.20 555
38 55 HRc 0.3 0.8 0.14 0.32 40 60 00.3 0.18 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 0.9 0.14 0.41 40 80 00.5 0.21 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 0.8 0.14 0.32 30 60 00.3 0.18 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.0 0.25 0.74 200 400 11.3 0.38 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
266
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 4.0 0.25 1.00 190 330 22.0 0.35 2250
2 190 HB 0.5 4.0 0.25 1.00 190 300 22.0 0.35 2220
3 250 HB 0.5 4.0 0.25 1.00 190 250 22.0 0.35 2200
6 180 HB 0.5 4.0 0.21 0.78 150 240 22.0 0.30 2200
4,6 230 HB 0.5 4.0 0.21 0.78 150 210 22.0 0.30 1180
5,7 280 HB 0.5 4.0 0.21 0.69 130 190 22.0 0.27 1150
8 350 HB 0.5 4.0 0.21 0.69 130 170 22.0 0.27 1140
10 220 HB 0.5 2.9 0.17 0.69 90 150 11.5 0.27 1130
10 280 HB 0.5 2.9 0.17 0.69 90 130 11.5 0.27 1120
11 320 HB 0.5 2.9 0.17 0.56 60 110 11.5 0.24 1100
11 350 HB 0.5 2.9 0.17 0.56 60 90 11.5 0.24 880
14 180 HB 0.5 4.0 0.21 0.78 190 250 22.0 0.30 2220
14 240 HB 0.5 4.0 0.17 0.69 160 210 22.0 0.30 1190
14 290 HB 0.5 3.1 0.17 0.56 70 130 11.5 0.24 1100
14 310 HB 0.5 3.1 0.17 0.56 70 120 11.5 0.24 990
12 200 HB 0.5 4.0 0.21 0.78 150 210 22.0 0.30 1190
13 42 HRc 0.5 3.1 0.21 0.63 90 150 11.5 0.24 1130
15 150 HB 0.5 4.0 0.25 1.00 150 240 22.0 0.35 2200
15 200 HB 0.5 4.0 0.25 1.00 150 220 22.0 0.35 1180
16 250 HB 0.5 4.0 0.25 1.00 150 190 22.0 0.35 1160
17,19 150 HB 0.5 4.0 0.21 0.88 100 200 22.0 0.30 1180
17,19 200 HB 0.5 4.0 0.21 0.88 100 180 22.0 0.30 1150
18,20 250 HB 0.5 4.0 0.21 0.88 100 150 22.0 0.30 1130
31,32 Incoloy 800 240 HB 0.5 3.1 0.17 0.56 25 45 11.5 0.24 332
33 Inconel 700 250 HB 0.5 3.1 0.17 0.56 25 45 11.5 0.24 330
34 Stellite 21 350 HB 0.5 3.1 0.17 0.56 25 45 11.5 0.24 330
36 TiAl6V4 - 0.5 3.1 0.17 0.63 40 65 11.5 0.27 555
37 T40 - 0.5 3.1 0.17 0.56 30 55 11.5 0.24 440
38 45 HRc 0.4 1.4 0.14 0.56 40 80 11.0 0.21 660
38 50 HRc 0.4 1.1 0.14 0.50 40 70 00.8 0.20 555
38 55 HRc 0.4 1.0 0.14 0.44 40 60 00.5 0.18 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.4 1.1 0.14 0.56 40 80 00.8 0.21 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.4 1.0 0.14 0.44 30 60 00.5 0.18 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.0 0.25 1.00 200 400 22.0 0.38 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
RDMT 1604 M0 – LT 30 | LT 3000
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
267
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
R D M Ws
Shape Clearance Angle Toleranced ± 0.05s ± 0.13
15°
Fixing,Chipbreaker
Ø dl
Copying SurfacingPocket MillingHelical Interpolation
Shap
M0001551
M0001550
-
-
Neutral
Neutral
4.76
3.97
12
10
RDMW 1204 M0 LT 30
RDMW 10T3 M0 LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
M0003408
M0002228
-
-
Neutral
Neutral
4.76
3.97
12
10
RDMW 1204 M0 LT 3000
RDMW 10T3 M0 LT 3000
Insert Designation Catalog Nr.Directions rl
LT 3000 Multi-MatTM General Usage – Premium
RDMW
MILLING
268
Cutters
End Mill for RDMW 10T3 M0
Screw:Key:
M2000597M2000602
Cutter Designation
LT 100 WL-W D032/3
Catalog Nr.
M2000685
D
32
z
3
Ap
5
D1
22
d L L1
32 180 80
α Ramp°
5
LT 100 WL-W D025/3 M200068425 3515 25 180 60 8
LT 100 WL-W-D020/2 M200068320 2510 20 180 80 12
DD1
L1
Ap
L
d
Shell Mill for RDMW 1204 M0
Screw:Key:
M2000597M2000602
Cutter Designation
LT 120 M-W-D063/5
LT 120 M-W-D100/7
Catalog Nr.
M2000689
M2000688
D
63
100
z
5
7
Ap
6
6
D1
51
88
d L
22
40
40
50
α Ramp°
3.5
1.5
LT 120 M-W-D050/4 M200178050 4638 22 40 5
LT 120 M-W-D080/6 M200069080 6668 27 50 2.5
LT 120 M-W-D040/4 M200069140 4628 16 40 7
D
D1
Ap
L
d
MILLING
269
Machining Conditions
RDMW 10T3 M0 – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 2.5 0.18 0.70 190 330 11.0 0.39 2250
2 190 HB 0.5 2.5 0.18 0.70 190 300 11.0 0.39 2220
3 250 HB 0.5 2.5 0.18 0.70 190 250 11.0 0.39 2200
6 180 HB 0.5 2.5 0.15 0.55 150 240 11.0 0.34 2200
4,6 230 HB 0.5 2.5 0.15 0.55 150 210 11.0 0.34 1180
5,7 280 HB 0.5 2.5 0.15 0.48 130 190 11.0 0.31 1150
8 350 HB 0.5 2.5 0.15 0.48 130 170 11.0 0.31 1140
10 220 HB 0.5 1.8 0.12 0.48 90 150 00.8 0.31 1130
10 280 HB 0.5 1.8 0.12 0.48 90 130 00.8 0.31 1120
11 320 HB 0.5 1.8 0.12 0.40 60 110 00.8 0.27 1100
11 350 HB 0.5 1.8 0.12 0.40 60 90 00.8 0.27 880
15 150 HB 0.5 2.5 0.18 0.70 150 240 11.0 0.39 2200
15 200 HB 0.5 2.5 0.18 0.70 150 220 11.0 0.39 1180
16 250 HB 0.5 2.5 0.18 0.70 150 190 11.0 0.39 1160
17,19 150 HB 0.5 2.5 0.15 0.62 100 200 11.0 0.34 1180
17,19 200 HB 0.5 2.5 0.15 0.62 100 180 11.0 0.34 1150
18,20 250 HB 0.5 2.5 0.15 0.62 100 150 11.0 0.34 1130
38 45 HRc 0.3 0.9 0.10 0.40 40 80 00.5 0.24 660
38 50 HRc 0.3 0.7 0.10 0.35 40 70 00.4 0.22 555
38 55 HRc 0.3 0.6 0.10 0.31 40 60 00.3 0.20 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 0.7 0.10 0.40 40 80 00.4 0.24 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 0.6 0.10 0.31 30 60 00.3 0.20 440
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Cast
Iron
Grey
Malleable & Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
MILLING
270
Machining Conditions
RDMW 1204 M0 – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 2.5 0.18 0.70 190 330 11.0 00.39 2250
2 190 HB 0.5 2.5 0.18 0.70 190 300 11.0 00.39 2220
3 250 HB 0.5 2.5 0.18 0.70 190 250 11.0 00.39 2200
6 180 HB 0.5 2.5 0.15 0.55 150 240 11.0 00.34 2200
4,6 230 HB 0.5 2.5 0.15 0.55 150 210 11.0 00.34 1180
5,7 280 HB 0.5 2.5 0.15 0.48 130 190 11.0 00.31 1150
8 350 HB 0.5 2.5 0.15 0.48 130 170 11.0 00.31 1140
10 220 HB 0.5 1.8 0.12 0.48 90 150 00.8 00.31 1130
10 280 HB 0.5 1.8 0.12 0.48 90 130 00.8 00.31 1120
11 320 HB 0.5 1.8 0.12 0.40 60 110 00.8 00.27 1100
11 350 HB 0.5 1.8 0.12 0.40 60 90 00.8 00.27 880
15 150 HB 0.5 2.5 0.18 0.70 150 240 11.0 00.39 2200
15 200 HB 0.5 2.5 0.18 0.70 150 220 11.0 00.39 1180
16 250 HB 0.5 2.5 0.18 0.70 150 190 11.0 00.39 1160
17,19 150 HB 0.5 2.5 0.15 0.62 100 200 11.0 00.34 1180
17,19 200 HB 0.5 2.5 0.15 0.62 100 180 11.0 00.34 1150
18,20 250 HB 0.5 2.5 0.15 0.62 100 150 11.0 00.34 1130
38 45 HRc 0.3 0.9 0.10 0.40 40 80 00.5 00.24 660
38 50 HRc 0.3 0.7 0.10 0.35 40 70 00.4 00.22 555
38 55 HRc 0.3 0.6 0.10 0.31 40 60 00.3 00.20 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 0.7 0.10 0.40 40 80 00.4 00.24 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 0.6 0.10 0.31 30 60 00.3 00.20 440
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Cast
Iron
Grey
Malleable & Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
271
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
R D M Xs
Shape Clearance Angle Toleranced ± 0.05s ± 0.13
15°
Fixing,Chipbreaker
Ø dl
Copying SurfacingPocket MillingHelical Interpolation
Shape
M0001553
M0001552
-
-
Neutral
Neutral
4.76
3.97
12
10
RDMX 1204 M0 LT 30
RDMX 10T3 M0 LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
M0003410
M0003409
-
-
Neutral
Neutral
4.76
3.97
12
10
RDMX 1204 M0 LT 3000
RDMX 10T3 M0 LT 3000
Insert Designation Catalog Nr.Directions rl
LT 3000 Multi-MatTM General Usage – Premium
RDMX
MILLING
272
Cutters
End Mill for RDMX 10T3 M0
Screw:Key:
M2000597M2000602
Cutter Designation
LT 100 WL-W D032/3
Catalog Nr.
M2000685
D
32
z
3
Ap
5
D1
22
d L L1
32 180 80
α Ramp°
5
LT 100 WL-W D025/3 M200068425 3515 25 180 60 8
LT 100 WL-W-D020/2 M200068320 2510 20 180 80 12
Shell Mill for RDMX 1204 M0
Screw:Key:
M2000597M2000602
Cutter Designation
LT 120 M-W-D063/5
LT 120 M-W-D100/7
Catalog Nr.
M2000689
M2000688
D
63
100
z
5
7
Ap
6
6
D1
51
88
d L
22
40
40
50
α Ramp°
3.5
1.5
LT 120 M-W-D050/4 M200178050 4638 22 40 5
LT 120 M-W-D080/6 M200069080 6668 27 50 2.5
LT 120 M-W-D040/4 M200069140 4628 16 40 7
DD1
L1
Ap
L
d
D
D1
Ap
L
d
MILLING
273
Machining Conditions
RDMX 10T3 M0 – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 2.5 0.18 0.64 190 330 11.000 0.345 2250
2 190 HB 0.5 2.5 0.18 0.64 190 300 11.000 0.345 2220
3 250 HB 0.5 2.5 0.18 0.64 190 250 11.000 0.345 2200
6 180 HB 0.5 2.5 0.15 0.50 150 240 11.000 0.300 2200
4,6 230 HB 0.5 2.5 0.15 0.50 150 210 11.000 0.300 1180
5,7 280 HB 0.5 2.5 0.15 0.44 130 190 11.000 0.270 1150
8 350 HB 0.5 2.5 0.15 0.44 130 170 11.000 0.270 1140
10 220 HB 0.5 1.8 0.12 0.44 90 150 00.750 0.270 1130
10 280 HB 0.5 1.8 0.12 0.44 90 130 00.750 0.270 1120
11 320 HB 0.5 1.8 0.12 0.36 60 110 00.750 0.240 1100
11 350 HB 0.5 1.8 0.12 0.36 60 90 00.750 0.240 880
14 180 HB 0.5 2.5 0.15 0.50 190 250 11.000 0.300 2220
14 240 HB 0.5 2.5 0.12 0.44 160 210 11.000 0.300 1190
14 290 HB 0.5 2.0 0.12 0.36 70 130 00.750 0.240 1100
14 310 HB 0.5 2.0 0.12 0.36 70 120 00.750 0.240 990
12 200 HB 0.5 2.5 0.15 0.50 150 210 11.000 0.300 1190
13 42 HRc 0.5 2.0 0.15 0.40 90 150 00.750 0.240 1130
15 150 HB 0.5 2.5 0.18 0.64 150 240 11.000 0.345 2200
15 200 HB 0.5 2.5 0.18 0.64 150 220 11.000 0.345 1180
16 250 HB 0.5 2.5 0.18 0.64 150 190 11.000 0.345 1160
17,19 150 HB 0.5 2.5 0.15 0.56 100 200 11.000 0.300 1180
17,19 200 HB 0.5 2.5 0.15 0.56 100 180 11.000 0.300 1150
18,20 250 HB 0.5 2.5 0.15 0.56 100 150 11.000 0.300 1130
31,32 Incoloy 800 240 HB 0.5 2.0 0.12 0.36 25 45 00.750 0.240 332
33 Inconel 700 250 HB 0.5 2.0 0.12 0.36 25 45 00.750 0.240 330
34 Stellite 21 350 HB 0.5 2.0 0.12 0.36 25 45 00.750 0.240 330
36 TiAl6V4 - 0.5 2.0 0.12 0.40 40 65 00.750 0.270 555
37 T40 - 0.5 2.0 0.12 0.36 30 55 00.750 0.240 440
38 45 HRc 0.3 0.9 0.10 0.36 40 80 00.500 0.210 660
38 50 HRc 0.3 0.7 0.10 0.32 40 70 00.375 0.195 555
38 55 HRc 0.3 0.6 0.10 0.28 40 60 00.250 0.180 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 0.7 0.10 0.36 40 80 00.375 0.210 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 0.6 0.10 0.28 30 60 00.250 0.180 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 2.5 0.18 0.64 200 400 11.000 0.375 280
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
1C35, Ck45, 1020, 1045, 1060, 28Mn6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
2
X100CrMo13, 440C,
G-X260NiCr42 11
4304, 316,
X5CrNi18-9
5
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
274
Machining Conditions
RDMX 1204 M0 – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 3.0 0.25 0.74 190 330 11.3 0.35 2250
2 190 HB 0.5 3.0 0.25 0.74 190 300 11.3 0.35 2220
3 250 HB 0.5 3.0 0.25 0.74 190 250 11.3 0.35 2200
6 180 HB 0.5 3.0 0.21 0.58 150 240 11.3 0.30 2200
4,6 230 HB 0.5 3.0 0.21 0.58 150 210 11.3 0.30 1180
5,7 280 HB 0.5 3.0 0.21 0.51 130 190 11.3 0.27 1150
8 350 HB 0.5 3.0 0.21 0.51 130 170 11.3 0.27 1140
10 220 HB 0.5 2.2 0.17 0.51 90 150 11.0 0.27 1130
10 280 HB 0.5 2.2 0.17 0.51 90 130 11.0 0.27 1120
11 320 HB 0.5 2.2 0.17 0.41 60 110 11.0 0.24 1100
11 350 HB 0.5 2.2 0.17 0.41 60 90 11.0 0.24 880
14 180 HB 0.5 3.0 0.21 0.58 190 250 11.3 0.30 2220
14 240 HB 0.5 3.0 0.17 0.51 160 210 11.3 0.30 1190
14 290 HB 0.5 2.4 0.17 0.41 70 130 11.0 0.24 1100
14 310 HB 0.5 2.4 0.17 0.41 70 120 11.0 0.24 990
12 200 HB 0.5 3.0 0.21 0.58 150 210 11.3 0.30 1190
13 42 HRc 0.5 2.4 0.21 0.46 90 150 11.0 0.24 1130
15 150 HB 0.5 3.0 0.25 0.74 150 240 11.3 0.35 2200
15 200 HB 0.5 3.0 0.25 0.74 150 220 11.3 0.35 1180
16 250 HB 0.5 3.0 0.25 0.74 150 190 11.3 0.35 1160
17,19 150 HB 0.5 3.0 0.21 0.64 100 200 11.3 0.30 1180
17,19 200 HB 0.5 3.0 0.21 0.64 100 180 11.3 0.30 1150
18,20 250 HB 0.5 3.0 0.21 0.64 100 150 11.3 0.30 1130
31,32 Incoloy 800 240 HB 0.5 2.4 0.17 0.41 25 45 11.0 0.24 332
33 Inconel 700 250 HB 0.5 2.4 0.17 0.41 25 45 11.0 0.24 330
34 Stellite 21 350 HB 0.5 2.4 0.17 0.41 25 45 11.0 0.24 330
36 TiAl6V4 - 0.5 2.4 0.17 0.46 40 65 11.0 0.27 555
37 T40 - 0.5 2.4 0.17 0.41 30 55 11.0 0.24 440
38 45 HRc 0.3 1.1 0.14 0.41 40 80 00.7 0.21 660
38 50 HRc 0.3 0.9 0.14 0.37 40 70 00.5 0.20 555
38 55 HRc 0.3 0.8 0.14 0.32 40 60 00.3 0.18 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 0.9 0.14 0.41 40 80 00.5 0.21 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 0.8 0.14 0.32 30 60 00.3 0.18 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.0 0.25 0.74 200 400 1.3 0.38 280
GG20, GG40, EN-GJL-250,
No30B
X100CrMo13, 440C,
G-X260NiCr42 11
8GGG40, GGG70,
50005
9
10
7
C35, Ck45, 1020, 1045, 1060, 28Mn6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
2
1
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
275
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
S D K T
Shape Clearance Angle Fixing,Chipbreaker
Toleranced ± 0.08m ± 0.013s ± 0.025
90°l
mØ d
15°
s
Chamfering Surfacing
M0000171- Neutral4.7612.70SDKT 1204 AETN LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
M0003411- Neutral4.7612.70SDKT 1204 AETN LT 3000
Insert Designation Catalog Nr.Directions rl
LT 3000 Multi-MatTM General Usage – Premium
SDKT
MILLING
276
Cutters
Shell Mill for SDKT 1204 AETN
Screw:Key:
M2000598M2000603
Cutter Designation
LT 670 M-W-D063/5*
LT 670 M-W-D050/4*
LT 670 M-W-D125/7*
LT 670 M-W-D080/6*
LT 670 M-W-D100/6*
LT 670 M-W-D160/8*
Catalog Nr.
M2000555
M2000553
M2000558
M2000556
M2000557
M2000559
D
76
63
138
93
113
173
z
5
4
7
6
6
8
Ap
6
6
6
6
6
6
D1
63
50
125
80
100
160
d
22
22
40
27
32
40
L
48
48
63
50
50
63
DD1
d
Ap
L
45°
* On request
MILLING
277
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 7.0 0.18 0.53 190 330 33.0 0.39 2250
2 190 HB 0.5 7.0 0.18 0.53 190 300 33.0 0.39 2220
3 250 HB 0.5 7.0 0.18 0.53 190 250 33.0 0.39 2200
6 180 HB 0.5 7.0 0.15 0.41 150 240 33.0 0.34 2200
4,6 230 HB 0.5 7.0 0.15 0.41 150 210 33.0 0.34 1180
5,7 280 HB 0.5 7.0 0.15 0.36 130 190 33.0 0.31 1150
8 350 HB 0.5 7.0 0.15 0.36 130 170 33.0 0.31 1140
10 220 HB 0.5 5.0 0.12 0.36 90 150 22.3 0.31 1130
10 280 HB 0.5 5.0 0.12 0.36 90 130 22.3 0.31 1120
11 320 HB 0.5 5.0 0.12 0.30 60 110 22.3 0.27 1100
11 350 HB 0.5 5.0 0.12 0.30 60 90 22.3 0.27 880
14 180 HB 0.5 7.0 0.15 0.36 190 250 33.0 0.31 2220
14 240 HB 0.5 7.0 0.12 0.33 160 210 33.0 0.31 1190
14 290 HB 0.5 5.0 0.12 0.30 70 130 22.3 0.27 1100
14 310 HB 0.5 5.0 0.12 0.30 70 120 22.3 0.27 990
12 200 HB 0.5 7.0 0.15 0.36 150 210 33.0 0.31 1190
13 42 HRc 0.5 5.0 0.15 0.30 90 150 22.3 0.27 1130
15 150 HB 0.5 7.0 0.18 0.53 150 240 33.0 0.39 2200
15 200 HB 0.5 7.0 0.18 0.53 150 220 33.0 0.39 1180
16 250 HB 0.5 7.0 0.18 0.53 150 190 33.0 0.39 1160
17,19 150 HB 0.5 7.0 0.15 0.46 100 200 33.0 0.34 1180
17,19 200 HB 0.5 7.0 0.15 0.46 100 180 33.0 0.34 1150
18,20 250 HB 0.5 7.0 0.15 0.46 100 150 33.0 0.34 1130
31,32 Incoloy 800 240 HB 0.5 5.0 0.12 0.30 25 45 22.3 0.27 332
33 Inconel 700 250 HB 0.5 5.0 0.12 0.30 25 45 22.3 0.27 330
34 Stellite 21 350 HB 0.5 5.0 0.12 0.30 25 45 22.3 0.27 330
36 TiAl6V4 - 0.5 5.0 0.12 0.33 40 65 22.3 0.31 555
37 T40 - 0.5 5.0 0.12 0.30 30 55 22.3 0.27 440
38 45 HRc 0.5 2.5 0.10 0.30 40 80 11.5 0.24 660
38 50 HRc 0.5 1.8 0.10 0.26 40 70 11.1 0.22 555
38 55 HRc 0.5 1.5 0.10 0.23 40 60 00.8 0.20 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.10 0.30 40 80 11.1 0.24 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.23 30 60 00.8 0.20 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 7.0 0.18 0.53 200 400 33.0 0.43 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
SDKT 1204 AETN – LT 30 | LT 3000
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
278
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
Shape Clearance Angle Toleranced ± 0.08m ± 0.013s ± 0.025
90°l
mØ d
15°
Fixing,Chipbreaker
ss
Copying Pocket MillingPlunging
Surfacing
Helical Interpolation
M00034122.00 Right4.769.52SDKX 0904-HF LT 3000
M00034132.50 Right5.5612.70SDKX 1205-HF LT 3000
Insert Designation Catalog Nr.Directions R prog.l
LT 3000 Multi-MatTM General Usage – Premium
Ramping Down
MILLING
279
Cutters
End Mill for SDKX 0904 HF
Shell Mill for SDKX 0904 HF
Screw Coupling for SDKX 0904 HF
Screw:Key:
M2001420M2000602
Screw:Key:
M2001420M2000602
Screw:Key:
M2001420M2000602
Cutter Designation
Cutter Designation
Cutter Designation
LT 902 W-W-D025/2
LT 902 M-W-D042/5
LT 902 S-W-D032/3
LT 902 WL-W-D025/2
LT 902 M-W-D040/5
LT 902 S-W-D025/2
LT 902 WL-W-D032/3
LT 902 M-W-D050/6
LT 902 S-W-D035/4
LT 902 M-W-D063/6*
LT 902 W-W-D032/3
LT 902 M-W-D052/6
LT 902 M-W-D066/6*
Catalog Nr.
Catalog Nr.
Catalog Nr.
M2003351
M2003342
M2003348
M2003350
M2003341
M2003347
M2003352
M2003343
M2003349
M2003345
M2003353
M2003344
M2003346
D
D
D
25
42
32
25
40
25
32
50
35
63
32
52
66
z
z
z
2
5
3
2
5
2
3
6
4
6
3
6
6
Ap
Ap
Ap
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
D1
D1
D1
9.6
26.6
16.6
9.6
24.6
9.6
16.6
34.6
19.6
47.6
16.6
36.6
50.6
d
d
d
L
L
L1
L1
25
16
M16
25
16
M12
120
40
35
60
200
40
35
60
32
22
M16
22
200
40
35
40
60
32
22
22
120
40
40
60
α Ramp°
α Ramp°
α Ramp°
3.5
0.8
2.0
3.5
0.8
3.5
2.0
0.7
1.5
0.6
2.0
0.7
0.6
d
L1
DD1
Ap
D
D1
d
Ap
L
D1
d
Ap
L1
DD1
SDKX
*On request
MILLING
280
Cutters
End Mill for SDKX 1205 HF
Shell Mill for SDKX 1205 HF
Screw Coupling for SDKX 1205 HF
Screw:Key:
M2000597M2000602
Screw:Key:
M2000597M2000602
Screw:Key:
M2000597M2000602
Cutter Designation
Cutter Designation
Cutter Designation
LT 903 W-W-D032/2
LT 903 M-W-D050/5
LT 903 S-W-D035/2
LT 903 S-W-D042/4*
*On request
LT 903 WL-W-D032/2
LT 903 M-W-D050/4
LT 903 S-W-D032/2
LT 903 M-W-D052/5
LT 903 S-W-D040/4
LT 903 M-W-D063/6
LT 903 M-W-D063/5
LT 903 M-W-D066/6
LT 903 M-W-D080/8
Catalog Nr.
Catalog Nr.
Catalog Nr.
M2003366
M2003357
M2003364
M2003356
M2003365
M2003661
M2003362
M2003358
M2003354
M2003360
M2003662
M2003361
M2003452
D
D
D
32
50
35
42
32
50
32
52
40
63
63
66
80
z
z
z
2
5
2
4
2
4
2
5
4
6
5
6
8
Ap
Ap
Ap
2
2
2
2
2
2
2
2
2
2
2
2
2
D1
D1
D1
11
29
14
21
11
29
11
31
19
42
42
45
59
d
d
d
L
L
L1
L1
32
22
M16
M16
32
22
M16
200
40
35
35
60
200
40
35
60
22
M16
22
40
35
40
22
22
27
40
40
50
α Ramp°
α Ramp°
α Ramp°
2.0
0.8
1.5
0.8
2.0
0.8
2.0
0.8
0.8
0.6
0.6
0.6
0.4
d
L1
DD1
Ap
D
D1
d
Ap
L
D1
d
Ap
L1
DD1
MILLING
281
Machining Conditions
SDKX 0904 HF – LT 3000
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High Alloyed
Stai
nles
s St
eel High Alloyed
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co based
Ti based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
1 125 HB 0.3 1.5 0.30 1.50 190 330 1.0 1.20 250
2 190 HB 0.3 1.5 0.30 1.50 190 300 1.0 1.20 220
3 250 HB 0.3 1.5 0.30 1.50 190 250 1.0 1.20 200
4,6 230 HB 0.3 1.2 0.30 1.36 150 210 0.8 1.00 180
5,7 280 HB 0.3 1.2 0.30 1.36 130 190 0.8 0.90 150
6 180 HB 0.3 1.2 0.30 1.36 150 240 0.8 1.00 200
8 350 HB 0.3 1.2 0.30 1.36 130 170 0.8 0.90 140
10 220 HB 0.3 1.2 0.30 1.20 90 150 0.7 0.80 130
280 HB 0.3 1.1 0.30 1.20 90 130 0.7 0.80 120
320 HB 0.3 1.0 0.30 1.20 60 110 0.7 0.70 100
350 HB 0.3 1.0 0.30 1.20 60 90 0.7 0.70 80
180 HB 0.3 1.3 0.30 0.76 190 250 0.8 0.50 220
240 HB 0.3 1.3 0.30 0.76 160 210 0.8 0.50 190
290 HB 0.3 1.1 0.30 0.46 70 130 0.7 0.30 100
310 HB 0.3 1.1 0.30 0.46 70 120 0.7 0.30 90
12 200 HB 0.3 1.2 0.30 0.52 150 210 0.8 0.40 190
13 42 HRc 0.3 1.0 0.30 0.46 90 150 0.7 0.30 130
150 HB 0.3 1.5 0.30 2.26 150 240 1.2 1.20 200
200 HB 0.3 1.5 0.30 1.50 150 220 1.2 1.20 180
16 250 HB 0.3 1.5 0.30 1.50 150 190 1.2 1.20 160
150 HB 0.3 1.5 0.30 1.36 100 200 1.2 1.00 180
200 HB 0.3 1.5 0.30 1.36 100 180 1.2 1.00 150
18,20 250 HB 0.3 1.5 0.30 1.36 100 150 1.2 1.00 130
31,32 Incoloy 800 240 HB 0.3 1.4 0.30 0.60 30 50 0.8 0.30 32
33 Inconel 700 250 HB 0.3 1.4 0.30 0.60 30 50 0.8 0.30 30
34 Stellite 21 350 HB 0.3 1.4 0.30 0.60 30 50 0.8 0.30 30
37 T40 - 0.3 1.5 0.30 0.52 30 60 0.8 0.30 40
36 TiAI6V4 - 0.3 1.4 0.30 0.52 40 70 0.8 0.30 55
45 HRc 0.3 0.6 0.30 0.90 40 80 0.6 0.50 60
50 HRc 0.3 0.5 0.30 0.76 40 70 0.5 0.50 55
55 HRc 0.3 0.5 0.30 0.60 40 60 0.4 0.40 50
40 Ni-Hard 2 400 HB 0.3 0.5 0.30 0.60 40 80 0.4 0.50 50
41 G-X300CrMo15 55 HRc 0.3 0.5 0.30 0.60 30 60 0.4 0.40 40
12 25 AlSi12 130 HB 0.3 1.5 0.30 0.76 200 400 1.5 0.70 280
11
38
17,19
15
14
X100CrMo13, 440C, G-
X260NiCr42
14
11
8GGG40, GGG70,
50005
9
10
6410, X6Cr17, 17-4
PH, 430
7GG20, GG40, EN-GJL-250, N030B
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
3X40CrM0V5, H13, M42, D3, S6-5-2,
12Ni19
1C35, Ck45, 1020,
1045, 1060, 28Mn6
242CrMo4, St50,
Ck60, 4140, 4340, 100Cr6
MILLING
282
Machining Conditions
SDKX 1205-HF – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.3 2.0 0.30 3.00 190 330 11.2 22.00 2250
2 190 HB 0.3 2.0 0.30 3.00 190 300 11.2 22.00 2220
3 250 HB 0.3 2.0 0.30 3.00 190 250 11.2 22.00 2200
6 180 HB 0.3 1.6 0.30 2.80 150 240 00.9 11.80 2200
4,6 230 HB 0.3 1.6 0.30 2.80 150 210 00.9 11.80 1180
5,7 280 HB 0.3 1.6 0.30 2.80 130 190 00.9 11.60 1150
8 350 HB 0.3 1.6 0.30 2.50 130 170 00.9 11.60 1140
10 220 HB 0.3 1.6 0.30 2.50 90 150 00.7 11.40 1130
10 280 HB 0.3 1.3 0.30 2.20 90 130 00.7 11.40 1120
11 320 HB 0.3 1.1 0.30 2.00 60 110 00.7 11.20 1100
11 350 HB 0.3 1.1 0.30 1.80 60 90 00.7 11.20 880
14 180 HB 0.3 1.5 0.30 1.10 190 250 00.9 00.90 2220
14 240 HB 0.3 1.5 0.30 1.10 160 210 00.9 00.90 1190
14 290 HB 0.3 1.2 0.30 0.70 70 130 00.8 00.60 1100
14 310 HB 0.3 1.2 0.30 0.70 70 120 00.8 00.60 990
12 200 HB 0.3 1.5 0.30 0.80 150 210 00.9 00.70 1190
13 42 HRc 0.3 1.1 0.30 0.70 90 150 00.8 00.60 1130
15 150 HB 0.3 2.0 0.30 3.00 150 240 11.5 22.00 2200
15 200 HB 0.3 2.0 0.30 3.00 150 220 11.5 22.00 1180
16 250 HB 0.3 2.0 0.30 3.00 150 190 11.5 22.00 1160
17,19 150 HB 0.3 2.0 0.30 2.50 100 200 11.5 11.90 1180
17,19 200 HB 0.3 2.0 0.30 2.50 100 180 11.5 11.90 1150
18,20 250 HB 0.3 2.0 0.30 2.50 100 150 11.5 11.90 1130
31,32 Incoloy 800 240 HB 0.3 1.8 0.30 0.70 25 45 11.0 00.60 332
33 Inconel 700 250 HB 0.3 1.8 0.30 0.60 25 45 11.0 00.60 330
34 Stellite 21 350 HB 0.3 1.8 0.30 0.60 25 45 11.0 00.60 330
36 TiAl6V4 - 0.3 1.8 0.30 0.70 40 65 11.0 00.60 555
37 T40 - 0.3 2.0 0.30 0.60 30 55 11.0 00.60 440
38 45 HRc 0.3 0.8 0.30 1.40 40 80 00.6 11.00 660
38 50 HRc 0.3 0.7 0.30 1.20 40 70 00.5 00.90 555
38 55 HRc 0.3 0.6 0.30 1.00 40 60 00.4 00.80 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 0.7 0.30 0.90 40 80 00.4 00.80 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 0.6 0.30 0.90 30 60 00.4 00.80 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 2.0 0.30 1.20 200 400 2.0 1.00 280
GG20, GG40, EN-GJL-250,
No30B
X100CrMo13, 440C,
G-X260NiCr42 11
8GGG40, GGG70,
50005
9
10
7
C35, Ck45, 1020, 1045, 1060, 28Mn6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
2
1
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
283
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
S E K N
Shape Clearance Angle Tolerance
90°l
mØ d
20°
Fixing,Chipbreaker
s
s ± 0.025For l = 12, d ± 0.08For l = 15, d ± 0.10
m ± 0.013
Chamfering Surfacing
90°
M0000450
M0000042
M0000041
-
-
-
Neutral
Neutral
Neutral
4.76
4.76
3.18
15.88
12.7
12.7
SEKN 1504 AFTN LT 30
SEKN 1204 AFTN LT 30
SEKN 1203 AFTN LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
SEKN
MILLING
284
Cutters
Shell Mill for SEKN 1203 AFTN
Screw:Key:
M2000608M2000609
Cutter Designation
LT 550 M-D-D063/5*
LT 550 M-D-D050/4*
LT 550 M-D-D125/7*
LT 550 M-D-D200/10*
LT 550 M-D-D080/6*
LT 550 M-D-D100/6*
LT 550 M-D-D160/7*
LT 550 M-D-D250/13*
Catalog Nr.
M2000564
M2000563
M2000567
M2000569
M2000565
M2000566
M2000568
M2000570
D
76
63
138
213
93
113
173
263
z
5
4
7
10
6
6
7
13
Ap
6
6
6
6
6
6
6
6
D1
63
50
125
200
80
100
160
250
d
22
22
40
60
27
32
40
60
L
48
48
63
63
50
50
63
63
DD1
d
Ap
L
45°
* On request
MILLING
285
Machining Conditions
SEKN 1203 AFTN – LT 30
min max min max min max D.O.C. Feed
1 125 HB 0.5 7.0 0.18 0.46 190 330 33.0 0.34 2250
2 190 HB 0.5 7.0 0.18 0.46 190 300 33.0 0.34 2220
3 250 HB 0.5 7.0 0.18 0.46 190 250 33.0 0.34 2200
6 180 HB 0.5 7.0 0.15 0.36 150 240 33.0 0.30 2200
4,6 230 HB 0.5 7.0 0.15 0.36 150 210 33.0 0.30 1180
5,7 280 HB 0.5 7.0 0.15 0.32 130 190 33.0 0.27 1150
8 350 HB 0.5 7.0 0.15 0.32 130 170 33.0 0.27 1140
10 220 HB 0.5 5.0 0.12 0.32 90 150 22.3 0.27 1130
10 280 HB 0.5 5.0 0.12 0.32 90 130 22.3 0.27 1120
11 320 HB 0.5 5.0 0.12 0.26 60 110 22.3 0.24 1100
11 350 HB 0.5 5.0 0.12 0.26 60 90 22.3 0.24 880
14 180 HB 0.5 7.0 0.15 0.32 190 250 33.0 0.27 2220
14 240 HB 0.5 7.0 0.12 0.29 160 210 33.0 0.27 1190
14 290 HB 0.5 5.0 0.12 0.26 70 130 22.3 0.24 1100
14 310 HB 0.5 5.0 0.12 0.26 70 120 22.3 0.24 990
12 200 HB 0.5 7.0 0.15 0.32 150 210 33.0 0.27 1190
13 42 HRc 0.5 5.0 0.15 0.26 90 150 22.3 0.24 1130
15 150 HB 0.5 7.0 0.18 0.46 150 240 33.0 0.34 2200
15 200 HB 0.5 7.0 0.18 0.46 150 220 33.0 0.34 1180
16 250 HB 0.5 7.0 0.18 0.46 150 190 33.0 0.34 1160
17,19 150 HB 0.5 7.0 0.15 0.41 100 200 33.0 0.30 1180
17,19 200 HB 0.5 7.0 0.15 0.41 100 180 33.0 0.30 1150
18,20 250 HB 0.5 7.0 0.15 0.41 100 150 33.0 0.30 1130
31,32 Incoloy 800 240 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 332
33 Inconel 700 250 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330
34 Stellite 21 350 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330
36 TiAl6V4 - 0.5 5.0 0.12 0.29 40 65 22.3 0.27 555
37 T40 - 0.5 5.0 0.12 0.26 30 55 22.3 0.24 440
38 45 HRc 0.5 2.5 0.10 0.26 40 80 11.5 0.21 660
38 50 HRc 0.5 1.8 0.10 0.23 40 70 11.1 0.19 555
38 55 HRc 0.5 1.5 0.10 0.20 40 60 00.8 0.18 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.10 0.26 40 80 11.1 0.21 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.20 30 60 00.8 0.18 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 7.0 0.18 0.46 200 400 33.0 0.37 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High Alloyed
Stai
nles
s St
eel High Alloyed
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co based
Ti based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
286
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 7.0 0.18 0.46 190 330 33.0 0.34 2250
2 190 HB 0.5 7.0 0.18 0.46 190 300 33.0 0.34 2220
3 250 HB 0.5 7.0 0.18 0.46 190 250 33.0 0.34 2200
6 180 HB 0.5 7.0 0.15 0.36 150 240 33.0 0.30 2200
4,6 230 HB 0.5 7.0 0.15 0.36 150 210 33.0 0.30 1180
5,7 280 HB 0.5 7.0 0.15 0.32 130 190 33.0 0.27 1150
8 350 HB 0.5 7.0 0.15 0.32 130 170 33.0 0.27 1140
10 220 HB 0.5 5.0 0.12 0.32 90 150 22.3 0.27 1130
10 280 HB 0.5 5.0 0.12 0.32 90 130 22.3 0.27 1120
11 320 HB 0.5 5.0 0.12 0.26 60 110 22.3 0.24 1100
11 350 HB 0.5 5.0 0.12 0.26 60 90 22.3 0.24 880
14 180 HB 0.5 7.0 0.15 0.32 190 250 33.0 0.27 2220
14 240 HB 0.5 7.0 0.12 0.29 160 210 33.0 0.27 1190
14 290 HB 0.5 5.0 0.12 0.26 70 130 22.3 0.24 1100
14 310 HB 0.5 5.0 0.12 0.26 70 120 22.3 0.24 990
12 200 HB 0.5 7.0 0.15 0.32 150 210 33.0 0.27 1190
13 42 HRc 0.5 5.0 0.15 0.26 90 150 22.3 0.24 1130
15 150 HB 0.5 7.0 0.18 0.46 150 240 33.0 0.34 2200
15 200 HB 0.5 7.0 0.18 0.46 150 220 33.0 0.34 1180
16 250 HB 0.5 7.0 0.18 0.46 150 190 33.0 0.34 1160
17,19 150 HB 0.5 7.0 0.15 0.41 100 200 33.0 0.30 1180
17,19 200 HB 0.5 7.0 0.15 0.41 100 180 33.0 0.30 1150
18,20 250 HB 0.5 7.0 0.15 0.41 100 150 33.0 0.30 1130
31,32 Incoloy 800 240 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 332
33 Inconel 700 250 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330
34 Stellite 21 350 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330
36 TiAl6V4 - 0.5 5.0 0.12 0.29 40 65 22.3 0.27 555
37 T40 - 0.5 5.0 0.12 0.26 30 55 22.3 0.24 440
38 45 HRc 0.5 2.5 0.10 0.26 40 80 11.5 0.21 660
38 50 HRc 0.5 1.8 0.10 0.23 40 70 11.1 0.19 555
38 55 HRc 0.5 1.5 0.10 0.20 40 60 00.8 0.18 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.10 0.26 40 80 11.1 0.21 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.20 30 60 00.8 0.18 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 7.0 0.18 0.46 200 400 33.0 0.37 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
SEKN 1204 AFTN – LT 30
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
287
Machining Conditions
SEKN 1504 AFTN – LT 30
min max min max min max D.O.C. Feed
1 125 HB 0.5 9.0 0.18 0.50 190 330 44.0 0.37 2250
2 190 HB 0.5 9.0 0.18 0.50 190 300 44.0 0.37 2220
3 250 HB 0.5 9.0 0.18 0.50 190 250 44.0 0.37 2200
6 180 HB 0.5 9.0 0.15 0.39 150 240 44.0 0.32 2200
4,6 230 HB 0.5 9.0 0.15 0.39 150 210 44.0 0.32 1180
5,7 280 HB 0.5 9.0 0.15 0.34 130 190 44.0 0.29 1150
8 350 HB 0.5 9.0 0.15 0.34 130 170 44.0 0.29 1140
10 220 HB 0.5 6.4 0.12 0.34 90 150 33.0 0.29 1130
10 280 HB 0.5 6.4 0.12 0.34 90 130 33.0 0.29 1120
11 320 HB 0.5 6.4 0.12 0.28 60 110 33.0 0.26 1100
11 350 HB 0.5 6.4 0.12 0.28 60 90 33.0 0.26 880
14 180 HB 0.5 9.0 0.15 0.34 190 250 44.0 0.29 2220
14 240 HB 0.5 9.0 0.12 0.31 160 210 44.0 0.29 1190
14 290 HB 0.5 6.4 0.12 0.28 70 130 33.0 0.26 1100
14 310 HB 0.5 6.4 0.12 0.28 70 120 33.0 0.26 990
12 200 HB 0.5 9.0 0.15 0.34 150 210 44.0 0.29 1190
13 42 HRc 0.5 6.4 0.15 0.28 90 150 33.0 0.26 1130
15 150 HB 0.5 9.0 0.18 0.50 150 240 44.0 0.37 2200
15 200 HB 0.5 9.0 0.18 0.50 150 220 44.0 0.37 1180
16 250 HB 0.5 9.0 0.18 0.50 150 190 44.0 0.37 1160
17,19 150 HB 0.5 9.0 0.15 0.43 100 200 44.0 0.32 1180
17,19 200 HB 0.5 9.0 0.15 0.43 100 180 44.0 0.32 1150
18,20 250 HB 0.5 9.0 0.15 0.43 100 150 44.0 0.32 1130
31,32 Incoloy 800 240 HB 0.5 6.4 0.12 0.28 25 45 33.0 0.26 332
33 Inconel 700 250 HB 0.5 6.4 0.12 0.28 25 45 33.0 0.26 330
34 Stellite 21 350 HB 0.5 6.4 0.12 0.28 25 45 33.0 0.26 330
36 TiAl6V4 - 0.5 6.4 0.12 0.31 40 65 33.0 0.29 555
37 T40 - 0.5 6.4 0.12 0.28 30 55 33.0 0.26 440
38 45 HRc 0.5 3.2 0.10 0.28 40 80 22.0 0.22 660
38 50 HRc 0.5 1.9 0.10 0.25 40 70 11.5 0.21 555
38 55 HRc 0.5 1.6 0.10 0.22 40 60 11.0 0.19 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.6 0.10 0.28 40 80 11.5 0.22 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.6 0.10 0.22 30 60 11.0 0.19 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.18 0.50 200 400 44.0 0.40 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High Alloyed
Stai
nles
s St
eel High Alloyed
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co based
Ti based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
288
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
S E K R
Shape Clearance Angle Insert TypeClamping,
Chipbreaker
s
Toleranced ± 0.08m ± 0.013s ± 0.025
90°l
mØ d
20°
Chamfering Surfacing
M0000044
M0000043
-
-
Neutral
Neutral
4.76
3.18
12.7
12.7
SEKR 1204 AFTN LT 30
SEKR 1203 AFTN LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
MILLING
289
Cutters
Shell Mill for SEKR 1203 AFTN
Screw:Key:
M2000608M2000609
Cutter Designation
LT 550 M-D-D063/5*
LT 550 M-D-D050/4*
LT 550 M-D-D125/7*
LT 550 M-D-D200/10*
LT 550 M-D-D080/6*
LT 550 M-D-D100/6*
LT 550 M-D-D160/7*
LT 550 M-D-D250/13*
Catalog Nr.
M2000564
M2000563
M2000567
M2000569
M2000565
M2000566
M2000568
M2000570
D
76
63
138
213
93
113
173
263
z
5
4
7
10
6
6
7
13
Ap
6
6
6
6
6
6
6
6
D1
63
50
125
200
80
100
160
250
d
22
22
40
60
27
32
40
60
L
48
48
63
63
50
50
63
63
DD1
d
Ap
L
45°
* On request
SEKR
MILLING
290
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 7.0 0.18 0.46 190 330 33.0 0.34 2250
2 190 HB 0.5 7.0 0.18 0.46 190 300 33.0 0.34 2220
3 250 HB 0.5 7.0 0.18 0.46 190 250 33.0 0.34 2200
6 180 HB 0.5 7.0 0.15 0.36 150 240 33.0 0.30 2200
4,6 230 HB 0.5 7.0 0.15 0.36 150 210 33.0 0.30 1180
5,7 280 HB 0.5 7.0 0.15 0.32 130 190 33.0 0.27 1150
8 350 HB 0.5 7.0 0.15 0.32 130 170 33.0 0.27 1140
10 220 HB 0.5 5.0 0.12 0.32 90 150 22.3 0.27 1130
10 280 HB 0.5 5.0 0.12 0.32 90 130 22.3 0.27 1120
11 320 HB 0.5 5.0 0.12 0.26 60 110 22.3 0.24 1100
11 350 HB 0.5 5.0 0.12 0.26 60 90 22.3 0.24 880
14 180 HB 0.5 7.0 0.15 0.32 190 250 33.0 0.27 2220
14 240 HB 0.5 7.0 0.12 0.29 160 210 33.0 0.27 1190
14 290 HB 0.5 5.0 0.12 0.26 70 130 22.3 0.24 1100
14 310 HB 0.5 5.0 0.12 0.26 70 120 22.3 0.24 990
12 200 HB 0.5 7.0 0.15 0.32 150 210 33.0 0.27 1190
13 42 HRc 0.5 5.0 0.15 0.26 90 150 22.3 0.24 1130
15 150 HB 0.5 7.0 0.18 0.46 150 240 33.0 0.34 2200
15 200 HB 0.5 7.0 0.18 0.46 150 220 33.0 0.34 1180
16 250 HB 0.5 7.0 0.18 0.46 150 190 33.0 0.34 1160
17,19 150 HB 0.5 7.0 0.15 0.41 100 200 33.0 0.30 1180
17,19 200 HB 0.5 7.0 0.15 0.41 100 180 33.0 0.30 1150
18,20 250 HB 0.5 7.0 0.15 0.41 100 150 33.0 0.30 1130
31,32 Incoloy 800 240 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 332
33 Inconel 700 250 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330
34 Stellite 21 350 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330
36 TiAl6V4 - 0.5 5.0 0.12 0.29 40 65 22.3 0.27 555
37 T40 - 0.5 5.0 0.12 0.26 30 55 22.3 0.24 440
38 45 HRc 0.5 2.5 0.10 0.26 40 80 11.5 0.21 660
38 50 HRc 0.5 1.8 0.10 0.23 40 70 11.1 0.19 555
38 55 HRc 0.5 1.5 0.10 0.20 40 60 00.8 0.18 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.10 0.26 40 80 11.1 0.21 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.20 30 60 00.8 0.18 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 7.0 0.18 0.46 200 400 33.0 0.37 280
1C35, Ck45, 1020,
1045, 1060, 28Mn6
242CrMo4, St50,
Ck60, 4140, 4340, 100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316, X5CrNi18-
9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
SEKR 1203 AFTN – LT 30
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
291
Machining Conditions
SEKR 1204 AFTN – LT 30
min max min max min max D.O.C. Feed
1 125 HB 0.5 7.0 0.18 0.46 190 330 33.0 0.34 2250
2 190 HB 0.5 7.0 0.18 0.46 190 300 33.0 0.34 2220
3 250 HB 0.5 7.0 0.18 0.46 190 250 33.0 0.34 2200
6 180 HB 0.5 7.0 0.15 0.36 150 240 33.0 0.30 2200
4,6 230 HB 0.5 7.0 0.15 0.36 150 210 33.0 0.30 1180
5,7 280 HB 0.5 7.0 0.15 0.32 130 190 33.0 0.27 1150
8 350 HB 0.5 7.0 0.15 0.32 130 170 33.0 0.27 1140
10 220 HB 0.5 5.0 0.12 0.32 90 150 22.3 0.27 1130
10 280 HB 0.5 5.0 0.12 0.32 90 130 22.3 0.27 1120
11 320 HB 0.5 5.0 0.12 0.26 60 110 22.3 0.24 1100
11 350 HB 0.5 5.0 0.12 0.26 60 90 22.3 0.24 880
14 180 HB 0.5 7.0 0.15 0.32 190 250 33.0 0.27 2220
14 240 HB 0.5 7.0 0.12 0.29 160 210 33.0 0.27 1190
14 290 HB 0.5 5.0 0.12 0.26 70 130 22.3 0.24 1100
14 310 HB 0.5 5.0 0.12 0.26 70 120 22.3 0.24 990
12 200 HB 0.5 7.0 0.15 0.32 150 210 33.0 0.27 1190
13 42 HRc 0.5 5.0 0.15 0.26 90 150 22.3 0.24 1130
15 150 HB 0.5 7.0 0.18 0.46 150 240 33.0 0.34 2200
15 200 HB 0.5 7.0 0.18 0.46 150 220 33.0 0.34 1180
16 250 HB 0.5 7.0 0.18 0.46 150 190 33.0 0.34 1160
17,19 150 HB 0.5 7.0 0.15 0.41 100 200 33.0 0.30 1180
17,19 200 HB 0.5 7.0 0.15 0.41 100 180 33.0 0.30 1150
18,20 250 HB 0.5 7.0 0.15 0.41 100 150 33.0 0.30 1130
31,32 Incoloy 800 240 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 332
33 Inconel 700 250 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330
34 Stellite 21 350 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330
36 TiAl6V4 - 0.5 5.0 0.12 0.29 40 65 22.3 0.27 555
37 T40 - 0.5 5.0 0.12 0.26 30 55 22.3 0.24 440
38 45 HRc 0.5 2.5 0.10 0.26 40 80 11.5 0.21 660
38 50 HRc 0.5 1.8 0.10 0.23 40 70 11.1 0.19 555
38 55 HRc 0.5 1.5 0.10 0.20 40 60 00.8 0.18 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.10 0.26 40 80 11.1 0.21 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.20 30 60 00.8 0.18 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 7.0 0.18 0.46 200 400 33.0 0.37 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High Alloyed
Stai
nles
s St
eel High Alloyed
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co based
Ti based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
292
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
S E K T
Shape Clearance Angle Toleranced ± 0.08m ± 0.013s ± 0.025
90°l
mØ d
20°
Fixing,Chipbreaker
s
Chamfering Surfacing
MILLING
M0000045
M0000455
0.85
1.20
Neutral
Neutral
4.76
3.97
12.70
13.40
SEKT 1204 AFTN LT 30
SEKT 12T3 AGSN LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
M0002230
M0002231
0.85
1.20
Neutral
Neutral
4.76
3.97
12.70
13.40
SEKT 1204 AFTN LT 3000
SEKT 12T3 AGSN LT 3000
Insert Designation Catalog Nr.Directions rl
LT 3000 Multi-MatTM General Usage – Premium
MILLING
293
Cutters
Shell Mill for SEKT 1204 AFTN
Screw:Key:
M2000599M2000603
Cutter Designation
LT 600 M-W-D050/4
LT 600 M-W-D040/3
LT 600 M-W-D100/6
LT 600 M-D-D160/8
LT 600 M-W-D063/5
LT 600 M-W-D080/6
LT 600 M-W-D125/7
Catalog Nr.
M2000547
M2000546
M2000550
M2000552
M2000548
M2000549
M2000551
D
63
53
113
173
76
93
138
z
4
3
6
8
5
6
7
Ap
6
6
6
6
6
6
6
D1
50
40
100
160
63
80
125
d
22
16
32
40
22
27
40
L
48
40
50
63
48
50
63
Shell Mill for SEKT 12T3 AGSN
Screw:Key:
M2001418M2000602
Cutter Designation
LT 610 M-W-D050/4
LT 610 M-W-D040/3
LT 610 M-W-D100/6
LT 610 M-D-D160/8
LT 610 M-W-D063/5
LT 610 M-W-D080/6
LT 610 M-W-D125/7
Catalog Nr.
M2001382
M2001431
M2001432
M2001434
M2001383
M2001384
M2001433
D
63
53
113
173
76
93
138
z
4
3
6
8
5
6
7
Ap
6
6
6
6
6
6
6
D1
50
40
100
160
63
80
125
d
22
16
32
40
22
27
40
L
48
40
50
63
48
50
63
DD1
d
Ap
L
45°
SEKT
MILLING
294
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 7.0 0.18 0.46 190 330 33.0 0.34 2250
2 190 HB 0.5 7.0 0.18 0.46 190 300 33.0 0.34 2220
3 250 HB 0.5 7.0 0.18 0.46 190 250 33.0 0.34 2200
6 180 HB 0.5 7.0 0.15 0.36 150 240 33.0 0.30 2200
4,6 230 HB 0.5 7.0 0.15 0.36 150 210 33.0 0.30 1180
5,7 280 HB 0.5 7.0 0.15 0.32 130 190 33.0 0.27 1150
8 350 HB 0.5 7.0 0.15 0.32 130 170 33.0 0.27 1140
10 220 HB 0.5 5.0 0.12 0.32 90 150 22.3 0.27 1130
10 280 HB 0.5 5.0 0.12 0.32 90 130 22.3 0.27 1120
11 320 HB 0.5 5.0 0.12 0.26 60 110 22.3 0.24 1100
11 350 HB 0.5 5.0 0.12 0.26 60 90 22.3 0.24 880
14 180 HB 0.5 7.0 0.15 0.32 190 250 33.0 0.27 2220
14 240 HB 0.5 7.0 0.12 0.29 160 210 33.0 0.27 1190
14 290 HB 0.5 5.0 0.12 0.26 70 130 22.3 0.24 1100
14 310 HB 0.5 5.0 0.12 0.26 70 120 22.3 0.24 990
12 200 HB 0.5 7.0 0.15 0.32 150 210 33.0 0.27 1190
13 42 HRc 0.5 5.0 0.15 0.26 90 150 22.3 0.24 1130
15 150 HB 0.5 7.0 0.18 0.46 150 240 33.0 0.34 2200
15 200 HB 0.5 7.0 0.18 0.46 150 220 33.0 0.34 1180
16 250 HB 0.5 7.0 0.18 0.46 150 190 33.0 0.34 1160
17,19 150 HB 0.5 7.0 0.15 0.41 100 200 33.0 0.30 1180
17,19 200 HB 0.5 7.0 0.15 0.41 100 180 33.0 0.30 1150
18,20 250 HB 0.5 7.0 0.15 0.41 100 150 33.0 0.30 1130
31,32 Incoloy 800 240 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 332
33 Inconel 700 250 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330
34 Stellite 21 350 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330
36 TiAl6V4 - 0.5 5.0 0.12 0.29 40 65 22.3 0.27 555
37 T40 - 0.5 5.0 0.12 0.26 30 55 22.3 0.24 440
38 45 HRc 0.5 2.5 0.10 0.26 40 80 11.5 0.21 660
38 50 HRc 0.5 1.8 0.10 0.23 40 70 11.1 0.19 555
38 55 HRc 0.5 1.5 0.10 0.20 40 60 00.8 0.18 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.10 0.26 40 80 11.1 0.21 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.20 30 60 00.8 0.18 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 7.0 0.18 0.46 200 400 33.0 0.37 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
SEKT 1204 AFTN – LT 30 | LT 3000
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
295
Machining Conditions
min max min max min max D.O.C. Feed
1 125 HB 0.5 7.0 0.18 0.46 190 330 33.0 0.34 2250
2 190 HB 0.5 7.0 0.18 0.46 190 300 33.0 0.34 2220
3 250 HB 0.5 7.0 0.18 0.46 190 250 33.0 0.34 2200
6 180 HB 0.5 7.0 0.15 0.36 150 240 33.0 0.30 2200
4,6 230 HB 0.5 7.0 0.15 0.36 150 210 33.0 0.30 1180
5,7 280 HB 0.5 7.0 0.15 0.32 130 190 33.0 0.27 1150
8 350 HB 0.5 7.0 0.15 0.32 130 170 33.0 0.27 1140
10 220 HB 0.5 5.0 0.12 0.32 90 150 22.3 0.27 1130
10 280 HB 0.5 5.0 0.12 0.32 90 130 22.3 0.27 1120
11 320 HB 0.5 5.0 0.12 0.26 60 110 22.3 0.24 1100
11 350 HB 0.5 5.0 0.12 0.26 60 90 22.3 0.24 880
14 180 HB 0.5 7.0 0.15 0.32 190 250 33.0 0.27 2220
14 240 HB 0.5 7.0 0.12 0.29 160 210 33.0 0.27 1190
14 290 HB 0.5 5.0 0.12 0.26 70 130 22.3 0.24 1100
14 310 HB 0.5 5.0 0.12 0.26 70 120 22.3 0.24 990
12 200 HB 0.5 7.0 0.15 0.32 150 210 33.0 0.27 1190
13 42 HRc 0.5 5.0 0.15 0.26 90 150 22.3 0.24 1130
15 150 HB 0.5 7.0 0.18 0.46 150 240 33.0 0.34 2200
15 200 HB 0.5 7.0 0.18 0.46 150 220 33.0 0.34 1180
16 250 HB 0.5 7.0 0.18 0.46 150 190 33.0 0.34 1160
17,19 150 HB 0.5 7.0 0.15 0.41 100 200 33.0 0.30 1180
17,19 200 HB 0.5 7.0 0.15 0.41 100 180 33.0 0.30 1150
18,20 250 HB 0.5 7.0 0.15 0.41 100 150 33.0 0.30 1130
31,32 Incoloy 800 240 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 332
33 Inconel 700 250 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330
34 Stellite 21 350 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330
36 TiAl6V4 - 0.5 5.0 0.12 0.29 40 65 22.3 0.27 555
37 T40 - 0.5 5.0 0.12 0.26 30 55 22.3 0.24 440
38 45 HRc 0.5 2.5 0.10 0.26 40 80 11.5 0.21 660
38 50 HRc 0.5 1.8 0.10 0.23 40 70 11.1 0.19 555
38 55 HRc 0.5 1.5 0.10 0.20 40 60 00.8 0.18 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.10 0.26 40 80 11.1 0.21 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.20 30 60 00.8 0.18 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 7.0 0.18 0.46 200 400 33.0 0.37 280
1C35, Ck45, 1020,
1045, 1060, 28Mn6
242CrMo4, St50,
Ck60, 4140, 4340, 100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316, X5CrNi18-
9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
SEKT 12T3 AGSN – LT 30 | LT 3000
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High Alloyed
Stai
nles
s St
eel High Alloyed
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co based
Ti based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
296
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
S N K X
Shape Toleranced ± 0.05m ± 0.013s ± 0.025
90° 0°
Clearance Angle
l
mØ d
Fixing,Chipbreaker
ss
Chamfering Surfacing
M0003415
M0002237
0.85
0.80
Neutral
Neutral
6.20
7.70
12.70
16.70
SNKX 1205-45 LT 3000
SNKX 1607-45 LT 3000
Insert Designation Catalog Nr.Directions rl
LT 3000 Multi-MatTM General Usage – Premium
MILLING
297
Cutters
Shell Mill for SNKX 1205-45°
Screw:Key:
M2003295M2003296
Cutter Designation
LT 946 M-W-D063/6
LT 946 M-W-D100/8
LT 946 M-W-D160/12
LT 946 M-W-D050/4
LT 946 M-W-D080/7
LT 946 M-W-D125/10
Catalog Nr.
M2003224
M2003226
M2003228
M2003223
M2003225
M2003227
D
77
114
174
64
94
139
z
6
8
12
4
7
10
Ap
6
6
6
6
6
6
D1
63
100
160
50
80
125
d
22
32
40
22
27
40
L
48
50
63
48
50
63
DD1
d
Ap
L
45°
Shell Mill for SNKX 1607-45°
Screw:Key:
M2002733M2000603
Cutter Designation
LT 947 M-W-D063/5
LT 947 M-W-D100/7
LT 947 M-W-D200/12*
LT 947 M-W-D050/4
LT 947 M-W-D080/6
LT 947 M-W-D160/10
LT 947 M-W-D125/8
LT 947 M-W-D250/14*
Catalog Nr.
M2002201
M2002203
M2003671
M2002200
M2002202
M2003670
M2002204
M2003672
D
82
119
69
99
144
219
179
269
z
5
7
4
6
8
12
10
14
Ap
7
7
7
7
7
7
7
7
D1
63
100
50
80
125
200
160
250
d
22
32
22
27
40
60
40
60
L
50
63
50
50
63
63
63
63SNKX 45
* On request
MILLING
298
Machining Conditions
SNKX 1205-45° – LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 5.0 0.16 0.34 190 330 33.0 0.30 2250
2 190 HB 0.5 5.0 0.16 0.34 190 300 33.0 0.30 2220
3 250 HB 0.5 5.0 0.16 0.34 190 250 33.0 0.30 2200
6 180 HB 0.5 5.0 0.14 0.28 150 240 33.0 0.26 2200
4,6 230 HB 0.5 5.0 0.14 0.28 150 210 33.0 0.26 1180
5,7 280 HB 0.5 5.0 0.14 0.26 130 190 33.0 0.24 1150
8 350 HB 0.5 5.0 0.14 0.26 130 170 33.0 0.24 1140
10 220 HB 0.5 5.0 0.11 0.28 90 150 33.0 0.26 1130
10 280 HB 0.5 5.0 0.11 0.28 90 130 33.0 0.26 1120
11 320 HB 0.5 5.0 0.11 0.24 60 110 33.0 0.22 1100
11 350 HB 0.5 5.0 0.11 0.24 60 90 33.0 0.22 880
14 180 HB 0.5 5.0 0.14 0.30 190 250 33.0 0.26 2220
14 240 HB 0.5 5.0 0.11 0.30 160 210 33.0 0.26 1190
14 290 HB 0.5 4.0 0.11 0.25 70 130 22.5 0.22 1100
14 310 HB 0.5 4.0 0.11 0.25 70 120 22.5 0.22 990
12 200 HB 0.5 5.0 0.14 0.30 150 210 33.0 0.26 1190
13 42 HRc 0.5 4.0 0.14 0.25 90 150 33.0 0.22 1130
15 150 HB 0.5 5.0 0.17 0.34 150 240 33.0 0.30 2200
15 200 HB 0.5 5.0 0.17 0.34 150 220 33.0 0.30 1180
16 250 HB 0.5 5.0 0.17 0.34 150 190 33.0 0.30 1160
17,19 150 HB 0.5 5.0 0.14 0.30 100 200 33.0 0.27 1180
17,19 200 HB 0.5 5.0 0.14 0.30 100 180 33.0 0.27 1150
18,20 250 HB 0.5 5.0 0.14 0.30 100 150 33.0 0.27 1130
31,32 Incoloy 800 240 HB 0.5 4.0 0.11 0.20 25 45 22.5 0.18 332
33 Inconel 700 250 HB 0.5 4.0 0.11 0.20 25 45 22.5 0.18 330
34 Stellite 21 350 HB 0.5 4.0 0.11 0.20 25 45 22.5 0.18 330
36 TiAl6V4 - 0.5 4.0 0.11 0.25 40 65 22.5 0.23 555
37 T40 - 0.5 4.0 0.11 0.23 30 55 22.5 0.20 440
38 45 HRc 0.4 2.0 0.10 0.22 40 80 11.3 0.18 660
38 50 HRc 0.4 2.0 0.10 0.20 40 70 11.3 0.16 555
38 55 HRc 0.4 1.0 0.10 0.18 40 60 11.0 0.15 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.4 2.0 0.10 0.22 40 80 11.3 0.19 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.4 1.0 0.10 0.20 30 60 11.0 0.17 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 5.0 0.17 0.36 200 400 33.0 0.30 280
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5X2CrNiN23-4,
S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
299
Machining Conditions
SNKX 1607-45° – LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 6.5 0.16 0.58 190 330 44.0 0.46 2250
2 190 HB 0.5 6.5 0.16 0.58 190 300 44.0 0.46 2220
3 250 HB 0.5 6.5 0.16 0.58 190 250 44.0 0.46 2200
6 180 HB 0.5 6.5 0.14 0.50 150 240 44.0 0.40 2200
4,6 230 HB 0.5 6.5 0.14 0.50 150 210 44.0 0.40 1180
5,7 280 HB 0.5 6.5 0.14 0.44 130 190 44.0 0.36 1150
8 350 HB 0.5 6.5 0.14 0.44 130 170 44.0 0.36 1140
10 220 HB 0.5 6.5 0.11 0.44 90 150 33.0 0.36 1130
10 280 HB 0.5 6.5 0.11 0.44 90 130 33.0 0.36 1120
11 320 HB 0.5 6.5 0.11 0.36 60 110 33.0 0.32 1100
11 350 HB 0.5 6.5 0.11 0.36 60 90 33.0 0.32 880
14 180 HB 0.5 6.5 0.14 0.44 190 250 44.0 0.34 2220
14 240 HB 0.5 6.5 0.11 0.40 160 210 44.0 0.34 1190
14 290 HB 0.5 5.0 0.11 0.36 70 130 33.0 0.30 1100
14 310 HB 0.5 5.0 0.11 0.36 70 120 33.0 0.30 990
12 200 HB 0.5 6.5 0.14 0.44 150 210 44.0 0.34 1190
13 42 HRc 0.5 5.0 0.14 0.40 90 150 33.0 0.30 1130
15 150 HB 0.5 6.5 0.17 0.58 150 240 44.0 0.46 2200
15 200 HB 0.5 6.5 0.17 0.58 150 220 44.0 0.46 1180
16 250 HB 0.5 6.5 0.17 0.58 150 190 44.0 0.46 1160
17,19 150 HB 0.5 6.5 0.14 0.52 100 200 44.0 0.40 1180
17,19 200 HB 0.5 6.5 0.14 0.52 100 180 44.0 0.40 1150
18,20 250 HB 0.5 6.5 0.14 0.52 100 150 44.0 0.40 1130
31,32 Incoloy 800 240 HB 0.5 5.0 0.11 0.36 25 45 33.0 0.30 332
33 Inconel 700 250 HB 0.5 5.0 0.11 0.36 25 45 33.0 0.30 330
34 Stellite 21 350 HB 0.5 5.0 0.11 0.36 25 45 33.0 0.30 330
36 TiAl6V4 - 0.5 5.0 0.11 0.40 40 65 33.0 0.34 555
37 T40 - 0.5 5.0 0.11 0.36 30 55 33.0 0.30 440
38 45 HRc 0.4 3.0 0.10 0.36 40 80 22.0 0.28 660
38 50 HRc 0.4 3.0 0.10 0.32 40 70 11.5 0.26 555
38 55 HRc 0.4 1.5 0.10 0.28 40 60 11.0 0.24 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.4 3.0 0.10 0.36 40 80 11.5 0.28 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.4 1.5 0.10 0.28 30 60 11.0 0.24 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.5 0.17 0.60 200 400 44.0 0.50 280
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5X2CrNiN23-4,
S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High Alloyed
Stai
nles
s St
eel High Alloyed
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co based
Ti based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
300
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
S N K X
Shape Toleranced ± 0.05m ± 0.013s ± 0.025
90° 0°
Clearance Angle
l
mØ d
Fixing,Chipbreaker
ss
Copying
Surfacing
Pocket MillingHelical Interpolation
M00021154.20 Right3.719.67SNKX 09T3-HF LT 30
Insert Designation Catalog Nr.Directions R prog.l
LT 30 Multi-MatTM General Usage – Standard
M00022364.20 Right3.719.67SNKX 09T3-HF LT 3000
Insert Designation Catalog Nr.Directions R prog.l
LT 3000 Multi-MatTM General Usage – Premium
Ramping Down
MILLING
301
Cutters
d
LL1
DD1
Ap
End Mill for SNKX 09T3-HF
Shell Mill for SNKX 09T3-HF
Screw Coupling for SNKX 09T3-HF
Screw:Key:
M2002101M2002911
Screw:Key:
M2002101M2002911
Screw:Key:
M2002101M2002911
Cutter Designation
Cutter Designation
Cutter Designation
LT 900 M-W-D042/5
LT 900 S-W-D032/4
LT 900 M-W-D040/5
LT 900 S-W-D025/3
LT 900 M-W-D050/6
LT 900 S-W-D035/4
LT 900 M-W-D063/6
LT 900 M-W-D052/6
LT 900 M-W-D066/6
Catalog Nr.
Catalog Nr.
Catalog Nr.
M2002122
M2002129
M2002121
M2002128
M2002123
M2002130
M2002125
M2002124
M2002127
D
D
D
42
32
40
25
50
35
63
52
66
z
z
z
5
4
5
3
6
4
6
6
6
Ap
Ap
Ap
1
1
1
1
1
1
1
1
1
D1
D1
D1
30.5
20.5
28.5
13.5
38.5
23.5
51.5
40.5
54.5
d
d
d
L
L
L1
L1
16
M16
16
M12
40
35
40
35
22
M16
22
40
35
40
22
22
40
40
α Ramp°
α Ramp°
α Ramp°
LT 900 W-W-D032/4 M200211932 4120.5 32 120 60 2.0
LT 900 WL-W-D032/3 M200212032 3120.5 32 200 60 2.0
3.2
2.0
LT 900 W-W-D025/3 M200211825 3113.5 25 120 60 3.5
LT 900 WL-W-D025/2 M200211725 2113.5 25 200 60 3.5
3.5
3.5
2.5
1.5
1.8
2.2
1.7
D
D1
d
Ap
L
d
L
ApL1
DD1
SNKX hf
MILLING
302
Machining Conditions
SNKX 09T3-HF – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.1 1.0 0.27 2.10 190 330 00.6 1.10 2250
2 190 HB 0.1 1.0 0.27 1.95 190 300 00.6 1.10 2220
3 250 HB 0.1 1.0 0.27 1.50 190 250 00.6 1.10 2200
6 180 HB 0.1 1.0 0.25 1.95 150 240 00.5 1.00 2200
4,6 230 HB 0.1 1.0 0.25 1.70 150 210 00.5 1.00 1180
5,7 280 HB 0.1 1.0 0.23 1.60 130 190 00.5 0.90 1150
8 350 HB 0.1 1.0 0.23 1.50 130 170 00.5 0.90 1140
10 220 HB 0.1 1.0 0.20 1.70 90 150 00.5 0.90 1130
10 280 HB 0.1 1.0 0.20 1.60 90 130 00.5 0.90 1120
11 320 HB 0.1 0.8 0.20 1.50 60 110 00.4 0.80 1100
11 350 HB 0.1 0.8 0.20 1.40 60 90 00.4 0.80 880
15 150 HB 0.1 1.0 0.20 2.40 150 240 00.6 1.10 2200
15 200 HB 0.1 1.0 0.20 2.40 150 220 00.6 1.10 1180
16 250 HB 0.1 1.0 0.20 2.40 150 190 00.6 1.10 1160
17,19 150 HB 0.1 1.0 0.20 1.80 100 200 00.5 1.00 1180
17,19 200 HB 0.1 1.0 0.20 1.80 100 180 00.5 1.00 1150
18,20 250 HB 0.1 1.0 0.20 1.80 100 150 00.5 1.00 1130
38 45 HRc 0.1 0.6 0.16 1.10 40 80 00.4 0.70 660
38 50 HRc 0.1 0.5 0.16 1.00 40 70 00.3 0.65 555
38 55 HRc 0.1 0.4 0.16 0.90 40 60 00.3 0.60 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.1 0.6 0.16 1.10 40 80 00.4 0.70 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.1 0.4 0.16 0.90 30 60 00.3 0.60 440
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
1C35, Ck45, 1020,
1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Cast
Iron
Grey
Malleable & Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
303
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
S P K Ns
Shape Tolerance
90°
Clearance Angle
l
mØ d
11°
Fixing,Chipbreakerm ± 0.013 s ± 0.025
For l = 12, d ± 0.08For l = 15, d ± 0.10
Surfacing
90°
M0001673
M0000047
M0000046
1.60
1.20
1.20
Right
Right
Right
4.76
4.76
3.21
15.88
12.7
12.7
SPKN 1504 EDTR LT 30
SPKN 1204 EDTR LT 30
SPKN 1203 EDTR LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
SPKN
MILLING
304
Cutters
Screw:Key: M2000609
M2000606
Shell Mill for SPKN 1203 EDTR
Cutter Designation
LT 750 M-D-D080/5*
LT 750 M-D-D063/4*
LT 750 M-D-D160/10*
LT 750 M-D-D250/14*
LT 750 M-D-D100/7*
LT 750 M-D-D125/8*
LT 750 M-D-D200/12*
Catalog Nr.
M2000572
M2000571
M2000576
M2000578
M2000574
M2000575
M2000577
D
86
69
166
256
106
131
206
z
5
4
10
14
7
8
12
Ap
9
9
9
9
9
9
9
D1
80
63
160
250
100
125
200
d
27
22
40
63
32
40
63
L
50
40
63
63
50
63
63
DD1
d
Ap
L
75°
* On request
MILLING
305
Machining Conditions
SPKN 1203 EDTR – LT 30
min max min max min max D.O.C. Feed
1 125 HB 0.5 7.0 0.18 0.43 190 330 33.0 0.30 2250
2 190 HB 0.5 7.0 0.18 0.43 190 300 33.0 0.30 2220
3 250 HB 0.5 7.0 0.18 0.43 190 250 33.0 0.30 2200
6 180 HB 0.5 7.0 0.15 0.34 150 240 33.0 0.26 2200
4,6 230 HB 0.5 7.0 0.15 0.34 150 210 33.0 0.26 1180
5,7 280 HB 0.5 7.0 0.15 0.30 130 190 33.0 0.23 1150
8 350 HB 0.5 7.0 0.15 0.30 130 170 33.0 0.23 1140
10 220 HB 0.5 5.0 0.12 0.30 90 150 22.3 0.23 1130
10 280 HB 0.5 5.0 0.12 0.30 90 130 22.3 0.23 1120
11 320 HB 0.5 5.0 0.12 0.24 60 110 22.3 0.21 1100
11 350 HB 0.5 5.0 0.12 0.24 60 90 22.3 0.21 880
15 150 HB 0.5 7.0 0.18 0.43 150 240 33.0 0.30 2200
15 200 HB 0.5 7.0 0.18 0.43 150 220 33.0 0.30 1180
16 250 HB 0.5 7.0 0.18 0.43 150 190 33.0 0.30 1160
17,19 150 HB 0.5 7.0 0.15 0.38 100 200 33.0 0.26 1180
17,19 200 HB 0.5 7.0 0.15 0.38 100 180 33.0 0.26 1150
18,20 250 HB 0.5 7.0 0.15 0.38 100 150 33.0 0.26 1130
38 45 HRc 0.5 2.5 0.10 0.24 40 80 11.5 0.18 660
38 50 HRc 0.5 1.8 0.10 0.22 40 70 11.1 0.17 555
38 55 HRc 0.5 1.5 0.10 0.19 40 60 00.8 0.16 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.10 0.24 40 80 11.1 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.19 30 60 00.8 0.16 440
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Cast
Iron
Grey
Malleable & Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
MILLING
306
Machining Conditions
SPKN 1204 EDTR – LT 30
min max min max min max D.O.C. Feed
1 125 HB 0.5 7.0 0.18 0.43 190 330 33.0 0.30 2250
2 190 HB 0.5 7.0 0.18 0.43 190 300 33.0 0.30 2220
3 250 HB 0.5 7.0 0.18 0.43 190 250 33.0 0.30 2200
6 180 HB 0.5 7.0 0.15 0.34 150 240 33.0 0.26 2200
4,6 230 HB 0.5 7.0 0.15 0.34 150 210 33.0 0.26 1180
5,7 280 HB 0.5 7.0 0.15 0.30 130 190 33.0 0.23 1150
8 350 HB 0.5 7.0 0.15 0.30 130 170 33.0 0.23 1140
10 220 HB 0.5 5.0 0.12 0.30 90 150 22.3 0.23 1130
10 280 HB 0.5 5.0 0.12 0.30 90 130 22.3 0.23 1120
11 320 HB 0.5 5.0 0.12 0.24 60 110 22.3 0.21 1100
11 350 HB 0.5 5.0 0.12 0.24 60 90 22.3 0.21 880
15 150 HB 0.5 7.0 0.18 0.43 150 240 33.0 0.30 2200
15 200 HB 0.5 7.0 0.18 0.43 150 220 33.0 0.30 1180
16 250 HB 0.5 7.0 0.18 0.43 150 190 33.0 0.30 1160
17,19 150 HB 0.5 7.0 0.15 0.38 100 200 33.0 0.26 1180
17,19 200 HB 0.5 7.0 0.15 0.38 100 180 33.0 0.26 1150
18,20 250 HB 0.5 7.0 0.15 0.38 100 150 33.0 0.26 1130
38 45 HRc 0.5 2.5 0.10 0.24 40 80 11.5 0.18 660
38 50 HRc 0.5 1.8 0.10 0.22 40 70 11.1 0.17 555
38 55 HRc 0.5 1.5 0.10 0.19 40 60 00.8 0.16 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.10 0.24 40 80 11.1 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.19 30 60 00.8 0.16 440
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Cast
Iron
Grey
Malleable & Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
MILLING
307
Machining Conditions
SPKN 1504 EDTR – LT 30
min max min max min max D.O.C. Feed
1 125 HB 0.5 9.0 0.18 0.43 190 330 44.0 0.30 2250
2 190 HB 0.5 9.0 0.18 0.43 190 300 44.0 0.30 2220
3 250 HB 0.5 9.0 0.18 0.43 190 250 44.0 0.30 2200
6 180 HB 0.5 9.0 0.15 0.34 150 240 44.0 0.26 2200
4,6 230 HB 0.5 9.0 0.15 0.34 150 210 44.0 0.26 1180
5,7 280 HB 0.5 9.0 0.15 0.30 130 190 44.0 0.23 1150
8 350 HB 0.5 9.0 0.15 0.30 130 170 44.0 0.23 1140
10 220 HB 0.5 6.5 0.12 0.30 90 150 33.0 0.23 1130
10 280 HB 0.5 6.5 0.12 0.30 90 130 33.0 0.23 1120
11 320 HB 0.5 6.5 0.12 0.24 60 110 33.0 0.21 1100
11 350 HB 0.5 6.5 0.12 0.24 60 90 33.0 0.21 880
15 150 HB 0.5 9.0 0.18 0.43 150 240 44.0 0.30 2200
15 200 HB 0.5 9.0 0.18 0.43 150 220 44.0 0.30 1180
16 250 HB 0.5 9.0 0.18 0.43 150 190 44.0 0.30 1160
17,19 150 HB 0.5 9.0 0.15 0.38 100 200 44.0 0.26 1180
17,19 200 HB 0.5 9.0 0.15 0.38 100 180 44.0 0.26 1150
18,20 250 HB 0.5 9.0 0.15 0.38 100 150 44.0 0.26 1130
38 45 HRc 0.5 3.2 0.10 0.24 40 80 22.0 0.18 660
38 50 HRc 0.5 2.3 0.10 0.22 40 70 11.5 0.17 555
38 55 HRc 0.5 1.9 0.10 0.19 40 60 11.0 0.16 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.6 0.10 0.24 40 80 11.5 0.18 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.9 0.10 0.19 30 60 11.0 0.16 440
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Cast
Iron
Grey
Malleable & Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
308
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
S P K R
Shape Toleranced ± 0.08m ± 0.013s ± 0.025
90°
Clearance Angle
l
mØ d
11°
Fixing,Chipbreaker
s
Surfacing
MILLING
90°
M0000049
M0000048
1.20
1.20
Right
Right
4.76
3.21
12.70
12.70
SPKR 1204 EDTR LT 30
SPKR 1203 EDTR LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
MILLING
309
Cutters
Shell Mill for SPKR 1203 EDTR
Cutter Designation
LT 750 M-D-D080/5*
LT 750 M-D-D063/4*
LT 750 M-D-D160/10*
LT 750 M-D-D250/14*
LT 750 M-D-D100/7*
LT 750 M-D-D125/8*
LT 750 M-D-D200/12*
Catalog Nr.
M2000572
M2000571
M2000576
M2000578
M2000574
M2000575
M2000577
D
86
69
166
256
106
131
206
z
5
4
10
14
7
8
12
Ap
9
9
9
9
9
9
9
D1
80
63
160
250
100
125
200
d
27
22
40
63
32
40
63
L
50
40
63
63
50
63
63
DD1
d
Ap
L
75°
* On request
SPKR
Screw:Key:
M2000606M2000609
MILLING
310
Machining Conditions
SPKR 1203 EDTR – LT 30
min max min max min max D.O.C. Feed
1 125 HB 0.5 7.0 0.18 0.38 190 330 33.0 0.26 2250
2 190 HB 0.5 7.0 0.18 0.38 190 300 33.0 0.26 2220
3 250 HB 0.5 7.0 0.18 0.38 190 250 33.0 0.26 2200
6 180 HB 0.5 7.0 0.15 0.30 150 240 33.0 0.23 2200
4,6 230 HB 0.5 7.0 0.15 0.30 150 210 33.0 0.23 1180
5,7 280 HB 0.5 7.0 0.15 0.26 130 190 33.0 0.21 1150
8 350 HB 0.5 7.0 0.15 0.26 130 170 33.0 0.21 1140
10 220 HB 0.5 5.0 0.12 0.26 90 150 22.3 0.21 1130
10 280 HB 0.5 5.0 0.12 0.26 90 130 22.3 0.21 1120
11 320 HB 0.5 5.0 0.12 0.22 60 110 22.3 0.18 1100
11 350 HB 0.5 5.0 0.12 0.22 60 90 22.3 0.18 880
14 180 HB 0.5 7.0 0.15 0.26 190 250 33.0 0.21 2220
14 240 HB 0.5 7.0 0.12 0.24 160 210 33.0 0.21 1190
14 290 HB 0.5 5.0 0.12 0.22 70 130 22.3 0.18 1100
14 310 HB 0.5 5.0 0.12 0.22 70 120 22.3 0.18 990
12 200 HB 0.5 7.0 0.15 0.26 150 210 33.0 0.21 1190
13 42 HRc 0.5 5.0 0.15 0.22 90 150 22.3 0.18 1130
15 150 HB 0.5 7.0 0.18 0.38 150 240 33.0 0.26 2200
15 200 HB 0.5 7.0 0.18 0.38 150 220 33.0 0.26 1180
16 250 HB 0.5 7.0 0.18 0.38 150 190 33.0 0.26 1160
17,19 150 HB 0.5 7.0 0.15 0.34 100 200 33.0 0.23 1180
17,19 200 HB 0.5 7.0 0.15 0.34 100 180 33.0 0.23 1150
18,20 250 HB 0.5 7.0 0.15 0.34 100 150 33.0 0.23 1130
31,32 Incoloy 800 240 HB 0.5 5.0 0.12 0.22 25 45 22.3 0.18 332
33 Inconel 700 250 HB 0.5 5.0 0.12 0.22 25 45 22.3 0.18 330
34 Stellite 21 350 HB 0.5 5.0 0.12 0.22 25 45 22.3 0.18 330
36 TiAl6V4 - 0.5 5.0 0.12 0.24 40 65 22.3 0.21 555
37 T40 - 0.5 5.0 0.12 0.22 30 55 22.3 0.18 440
38 45 HRc 0.5 2.5 0.10 0.22 40 80 11.5 0.16 660
38 50 HRc 0.5 1.8 0.10 0.19 40 70 11.1 0.15 555
38 55 HRc 0.5 1.5 0.10 0.17 40 60 00.8 0.14 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.10 0.22 40 80 11.1 0.16 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.17 30 60 00.8 0.14 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 7.0 0.18 0.38 200 400 33.0 0.29 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
311
Machining Conditions
SPKR 1204 EDTR – LT 30
min max min max min max D.O.C. Feed
1 125 HB 0.5 7.0 0.18 0.38 190 330 33.0 0.26 2250
2 190 HB 0.5 7.0 0.18 0.38 190 300 33.0 0.26 2220
3 250 HB 0.5 7.0 0.18 0.38 190 250 33.0 0.26 2200
6 180 HB 0.5 7.0 0.15 0.30 150 240 33.0 0.23 2200
4,6 230 HB 0.5 7.0 0.15 0.30 150 210 33.0 0.23 1180
5,7 280 HB 0.5 7.0 0.15 0.26 130 190 33.0 0.21 1150
8 350 HB 0.5 7.0 0.15 0.26 130 170 33.0 0.21 1140
10 220 HB 0.5 5.0 0.12 0.26 90 150 22.3 0.21 1130
10 280 HB 0.5 5.0 0.12 0.26 90 130 22.3 0.21 1120
11 320 HB 0.5 5.0 0.12 0.22 60 110 22.3 0.18 1100
11 350 HB 0.5 5.0 0.12 0.22 60 90 22.3 0.18 880
14 180 HB 0.5 7.0 0.15 0.26 190 250 33.0 0.21 2220
14 240 HB 0.5 7.0 0.12 0.24 160 210 33.0 0.21 1190
14 290 HB 0.5 5.0 0.12 0.22 70 130 22.3 0.18 1100
14 310 HB 0.5 5.0 0.12 0.22 70 120 22.3 0.18 990
12 200 HB 0.5 7.0 0.15 0.26 150 210 33.0 0.21 1190
13 42 HRc 0.5 5.0 0.15 0.22 90 150 22.3 0.18 1130
15 150 HB 0.5 7.0 0.18 0.38 150 240 33.0 0.26 2200
15 200 HB 0.5 7.0 0.18 0.38 150 220 33.0 0.26 1180
16 250 HB 0.5 7.0 0.18 0.38 150 190 33.0 0.26 1160
17,19 150 HB 0.5 7.0 0.15 0.34 100 200 33.0 0.23 1180
17,19 200 HB 0.5 7.0 0.15 0.34 100 180 33.0 0.23 1150
18,20 250 HB 0.5 7.0 0.15 0.34 100 150 33.0 0.23 1130
31,32 Incoloy 800 240 HB 0.5 5.0 0.12 0.22 25 45 22.3 0.18 332
33 Inconel 700 250 HB 0.5 5.0 0.12 0.22 25 45 22.3 0.18 330
34 Stellite 21 350 HB 0.5 5.0 0.12 0.22 25 45 22.3 0.18 330
36 TiAl6V4 - 0.5 5.0 0.12 0.24 40 65 22.3 0.21 555
37 T40 - 0.5 5.0 0.12 0.22 30 55 22.3 0.18 440
38 45 HRc 0.5 2.5 0.10 0.22 40 80 11.5 0.16 660
38 50 HRc 0.5 1.8 0.10 0.19 40 70 11.1 0.15 555
38 55 HRc 0.5 1.5 0.10 0.17 40 60 00.8 0.14 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.10 0.22 40 80 11.1 0.16 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.17 30 60 00.8 0.14 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 7.0 0.18 0.38 200 400 33.0 0.29 280
X100CrMo13, 440C,
G-X260NiCr42 Steel
11
GGG40, GGG70, 50005
Fe, Ni & Co based
9
Ti based 10
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
Austenitic 4304, 316,
X5CrNi18-9
Duplex 5X2CrNiN23-4,
S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6
Low alloyed 2
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High Alloyed
Stai
nles
s St
eel High Alloyed
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co based
Ti based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
312
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
S P M T
Shape Toleranced ± 0.08m ± 0.13s ± 0.13
90°
Clearance Angle
l
mØ d
11°
Fixing,Chipbreaker
s
Shoulder Milling SurfacingSlotting
MILLING
M00030630.80 Neutral3.719.53SPMT 09T308 TN LT 30
M00031050.80 Neutral4.8012.70SPMT 120408 TN LT 30
M00031000.40 Neutral3.26.35SPMT 060304 TN LT 30
M00012260.80 Neutral3.9713.29SPMT 12T308 LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
M00034170.80 Neutral3.719.53SPMT 09T308 TN LT 3000
M00034190.80 Neutral4.8012.70SPMT 120408 TN LT 3000
M00034160.40 Neutral3.26.35SPMT 060304 TN LT 3000
M00034200.80 Neutral3.9713.29SPMT 12T308 LT 3000
Insert Designation Catalog Nr.Directions rl
LT 3000 Multi-MatTM General Usage – Premium
MILLING
313
Machining Conditions
SPMT 060304 TN – LT 30 | LT 3000
SPMT
min max min max min max D.O.C. Feed
1 125 HB 0.3 6.0 0.06 0.12 190 330 22.4 0.10 2250
2 190 HB 0.3 6.0 0.06 0.10 190 300 22.4 0.08 2220
3 250 HB 0.3 6.0 0.06 0.10 190 250 22.4 0.08 2200
6 180 HB 0.3 6.0 0.06 0.12 150 240 22.4 0.10 2200
4,6 230 HB 0.3 6.0 0.06 0.10 150 210 22.4 0.08 1180
5,7 280 HB 0.3 6.0 0.05 0.10 130 190 22.4 0.08 1150
8 350 HB 0.3 6.0 0.05 0.10 130 170 22.4 0.08 1140
10 220 HB 0.3 4.3 0.06 0.08 90 150 11.8 0.07 1130
10 280 HB 0.3 4.3 0.05 0.10 90 130 11.8 0.08 1120
11 320 HB 0.3 4.3 0.05 0.08 60 110 11.8 0.06 1100
11 350 HB 0.3 4.3 0.05 0.08 60 90 11.8 0.06 880
14 180 HB 0.3 6.0 0.06 0.08 190 250 22.4 0.07 2220
14 240 HB 0.3 6.0 0.05 0.08 160 210 22.4 0.07 1190
14 290 HB 0.3 4.3 0.05 0.08 70 130 11.8 0.07 1100
14 310 HB 0.3 4.3 0.05 0.07 70 120 11.8 0.06 990
12 200 HB 0.3 6.0 0.05 0.08 150 210 22.4 0.07 1190
13 42 HRc 0.3 4.3 0.05 0.07 90 150 11.8 0.06 1130
15 150 HB 0.3 6.0 0.05 0.14 150 240 22.4 0.12 2200
15 200 HB 0.3 6.0 0.05 0.12 150 220 22.4 0.10 1180
16 250 HB 0.3 6.0 0.05 0.12 150 190 22.4 0.10 1160
17,19 150 HB 0.3 6.0 0.05 0.14 100 200 22.4 0.12 1180
17,19 200 HB 0.3 6.0 0.05 0.12 100 180 22.4 0.10 1150
18,20 250 HB 0.3 6.0 0.05 0.12 100 150 22.4 0.10 1130
31,32 Incoloy 800 240 HB 0.3 4.3 0.04 0.08 25 45 11.8 0.06 332
33 Inconel 700 250 HB 0.3 4.3 0.04 0.08 25 45 11.8 0.06 330
34 Stellite 21 350 HB 0.3 4.3 0.04 0.08 25 45 11.8 0.06 330
36 TiAl6V4 - 0.3 4.3 0.04 0.08 40 65 11.8 0.06 555
37 T40 - 0.3 4.3 0.04 0.08 30 55 11.8 0.06 440
38 45 HRc 0.3 2.1 0.04 0.10 40 80 11.2 0.08 660
38 50 HRc 0.3 1.3 0.04 0.08 40 70 00.9 0.06 555
38 55 HRc 0.3 0.9 0.04 0.06 40 60 00.6 0.05 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.7 0.04 0.06 40 80 00.9 0.05 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 0.9 0.04 0.06 30 60 00.6 0.05 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 6.0 0.08 0.14 200 400 2.4 0.12 280
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High Alloyed
Stai
nles
s St
eel High Alloyed
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co based
Ti based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
314
Machining Conditions
SPMT 09T308 TN – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 9.0 0.07 0.17 190 330 22.4 0.15 2250
2 190 HB 0.5 9.0 0.06 0.15 190 300 22.4 0.13 2220
3 250 HB 0.5 9.0 0.06 0.15 190 250 22.4 0.13 2200
6 180 HB 0.5 9.0 0.07 0.17 150 240 22.4 0.15 2200
4,6 230 HB 0.5 9.0 0.06 0.15 150 210 22.4 0.13 1180
5,7 280 HB 0.5 9.0 0.05 0.13 130 190 22.4 0.11 1150
8 350 HB 0.5 9.0 0.05 0.13 130 170 22.4 0.11 1140
10 220 HB 0.5 6.5 0.07 0.15 90 150 11.8 0.13 1130
10 280 HB 0.5 6.5 0.05 0.13 90 130 11.8 0.11 1120
11 320 HB 0.5 6.5 0.05 0.10 60 110 11.8 0.08 1100
11 350 HB 0.5 6.5 0.05 0.10 60 90 11.8 0.08 880
14 180 HB 0.5 9.0 0.07 0.12 190 250 22.4 0.10 2220
14 240 HB 0.5 9.0 0.05 0.10 160 210 22.4 0.08 1190
14 290 HB 0.5 6.5 0.05 0.10 70 130 11.8 0.08 1100
14 310 HB 0.5 6.5 0.05 0.08 70 120 11.8 0.07 990
12 200 HB 0.5 9.0 0.05 0.08 150 210 22.4 0.07 1190
13 42 HRc 0.5 6.5 0.05 0.08 90 150 11.8 0.07 1130
15 150 HB 0.5 9.0 0.06 0.22 150 240 22.4 0.18 2200
15 200 HB 0.5 9.0 0.06 0.22 150 220 22.4 0.18 1180
16 250 HB 0.5 9.0 0.06 0.20 150 190 22.4 0.16 1160
17,19 150 HB 0.5 9.0 0.06 0.22 100 200 22.4 0.18 1180
17,19 200 HB 0.5 9.0 0.05 0.22 100 180 22.4 0.18 1150
18,20 250 HB 0.5 9.0 0.05 0.20 100 150 22.4 0.16 1130
31,32 Incoloy 800 240 HB 0.5 6.5 0.04 0.12 25 45 11.8 0.10 332
33 Inconel 700 250 HB 0.5 6.5 0.04 0.12 25 45 11.8 0.10 330
34 Stellite 21 350 HB 0.5 6.5 0.04 0.12 25 45 11.8 0.10 330
36 TiAl6V4 - 0.5 6.5 0.04 0.12 40 65 11.8 0.10 555
37 T40 - 0.5 6.5 0.04 0.12 30 55 11.8 0.10 440
38 45 HRc 0.5 3.2 0.04 0.12 40 80 11.2 0.10 660
38 50 HRc 0.5 1.9 0.04 0.10 40 70 00.9 0.08 555
38 55 HRc 0.5 1.3 0.04 0.08 40 60 00.6 0.06 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.6 0.04 0.08 40 80 00.9 0.06 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.3 0.04 0.08 30 60 00.6 0.06 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.08 0.16 200 400 2.4 0.13 280
1C35, Ck45, 1020,
1045, 1060, 28Mn6
242CrMo4, St50,
Ck60, 4140, 4340, 100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316, X5CrNi18-
9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
315
Machining Conditions
SPMT 120408 TN – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 9.0 0.13 0.29 190 330 33.0 0.18 2250
2 190 HB 0.5 9.0 0.13 0.29 190 300 33.0 0.18 2220
3 250 HB 0.5 9.0 0.13 0.29 190 250 33.0 0.18 2200
6 180 HB 0.5 9.0 0.11 0.23 150 240 33.0 0.16 2200
4,6 230 HB 0.5 9.0 0.11 0.23 150 210 33.0 0.16 1180
5,7 280 HB 0.5 9.0 0.11 0.20 130 190 33.0 0.14 1150
8 350 HB 0.5 9.0 0.11 0.20 130 170 33.0 0.14 1140
10 220 HB 0.5 6.5 0.08 0.20 90 150 22.3 0.14 1130
10 280 HB 0.5 6.5 0.08 0.20 90 130 22.3 0.14 1120
11 320 HB 0.5 6.5 0.08 0.16 60 110 22.3 0.13 1100
11 350 HB 0.5 6.5 0.08 0.16 60 90 22.3 0.13 880
14 180 HB 0.5 9.0 0.11 0.23 190 250 33.0 0.16 2220
14 240 HB 0.5 9.0 0.08 0.20 160 210 33.0 0.16 1190
14 290 HB 0.5 6.5 0.08 0.16 70 130 22.3 0.13 1100
14 310 HB 0.5 6.5 0.08 0.16 70 120 22.3 0.13 990
12 200 HB 0.5 9.0 0.11 0.23 150 210 33.0 0.16 1190
13 42 HRc 0.5 6.5 0.11 0.18 90 150 22.3 0.13 1130
15 150 HB 0.5 9.0 0.13 0.29 150 240 33.0 0.18 2200
15 200 HB 0.5 9.0 0.13 0.29 150 220 33.0 0.18 1180
16 250 HB 0.5 9.0 0.13 0.29 150 190 33.0 0.18 1160
17,19 150 HB 0.5 9.0 0.11 0.25 100 200 33.0 0.16 1180
17,19 200 HB 0.5 9.0 0.11 0.25 100 180 33.0 0.16 1150
18,20 250 HB 0.5 9.0 0.11 0.25 100 150 33.0 0.16 1130
31,32 Incoloy 800 240 HB 0.5 6.5 0.08 0.16 25 45 22.3 0.13 332
33 Inconel 700 250 HB 0.5 6.5 0.08 0.16 25 45 22.3 0.13 330
34 Stellite 21 350 HB 0.5 6.5 0.08 0.16 25 45 22.3 0.13 330
36 TiAl6V4 - 0.5 6.5 0.08 0.18 40 65 22.3 0.14 555
37 T40 - 0.5 6.5 0.08 0.16 30 55 22.3 0.13 440
38 45 HRc 0.5 3.2 0.07 0.16 40 80 11.5 0.11 660
38 50 HRc 0.5 1.9 0.07 0.14 40 70 11.1 0.10 555
38 55 HRc 0.5 1.0 0.07 0.13 40 60 00.8 0.10 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.6 0.07 0.16 40 80 11.1 0.11 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.0 0.07 0.13 30 60 00.8 0.10 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.13 0.29 200 400 3.0 0.20 280
1C35, Ck45, 1020,
1045, 1060, 28Mn6
242CrMo4, St50,
Ck60, 4140, 4340, 100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316, X5CrNi18-
9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High Alloyed
Stai
nles
s St
eel High Alloyed
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co based
Ti based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
316
Machining Conditions
SPMT 12T308 – LT 30 | LT 3000
min max min max min max D.O.C. Feed
1 125 HB 0.5 9.0 0.13 0.29 190 330 33.0 00.18 2250
2 190 HB 0.5 9.0 0.13 0.29 190 300 33.0 00.18 2220
3 250 HB 0.5 9.0 0.13 0.29 190 250 33.0 00.18 2200
6 180 HB 0.5 9.0 0.11 0.23 150 240 33.0 00.16 2200
4,6 230 HB 0.5 9.0 0.11 0.23 150 210 33.0 00.16 1180
5,7 280 HB 0.5 9.0 0.11 0.20 130 190 33.0 00.14 1150
8 350 HB 0.5 9.0 0.11 0.20 130 170 33.0 00.14 1140
10 220 HB 0.5 6.5 0.08 0.20 90 150 22.3 00.14 1130
10 280 HB 0.5 6.5 0.08 0.20 90 130 22.3 00.14 1120
11 320 HB 0.5 6.5 0.08 0.16 60 110 22.3 00.13 1100
11 350 HB 0.5 6.5 0.08 0.16 60 90 22.3 00.13 880
14 180 HB 0.5 9.0 0.11 0.23 190 250 33.0 00.16 2220
14 240 HB 0.5 9.0 0.08 0.20 160 210 33.0 00.16 1190
14 290 HB 0.5 6.5 0.08 0.16 70 130 22.3 00.13 1100
14 310 HB 0.5 6.5 0.08 0.16 70 120 22.3 00.13 990
12 200 HB 0.5 9.0 0.11 0.23 150 210 33.0 00.16 1190
13 42 HRc 0.5 6.5 0.11 0.18 90 150 22.3 00.13 1130
15 150 HB 0.5 9.0 0.13 0.29 150 240 33.0 00.18 2200
15 200 HB 0.5 9.0 0.13 0.29 150 220 33.0 00.18 1180
16 250 HB 0.5 9.0 0.13 0.29 150 190 33.0 00.18 1160
17,19 150 HB 0.5 9.0 0.11 0.25 100 200 33.0 00.16 1180
17,19 200 HB 0.5 9.0 0.11 0.25 100 180 33.0 00.16 1150
18,20 250 HB 0.5 9.0 0.11 0.25 100 150 33.0 00.16 1130
31,32 Incoloy 800 240 HB 0.5 6.5 0.08 0.16 25 45 22.3 00.13 332
33 Inconel 700 250 HB 0.5 6.5 0.08 0.16 25 45 22.3 00.13 330
34 Stellite 21 350 HB 0.5 6.5 0.08 0.16 25 45 22.3 00.13 330
36 TiAl6V4 - 0.5 6.5 0.08 0.18 40 65 22.3 00.14 555
37 T40 - 0.5 6.5 0.08 0.16 30 55 22.3 00.13 440
38 45 HRc 0.5 3.2 0.07 0.16 40 80 11.5 00.11 660
38 50 HRc 0.5 1.9 0.07 0.14 40 70 11.1 00.10 555
38 55 HRc 0.5 1.0 0.07 0.13 40 60 00.8 00.10 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.6 0.07 0.16 40 80 11.1 00.11 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.0 0.07 0.13 30 60 00.8 00.10 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.13 0.29 200 400 3.0 0.20 280
1C35, Ck45, 1020,
1045, 1060, 28Mn6
242CrMo4, St50,
Ck60, 4140, 4340, 100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316, X5CrNi18-
9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
317
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
S P U Ns
Shape Toleranced ± 0.13m ± 0.20s ± 0.13
90°
Clearance Angle
l
mØ d
11°
Fixing,Chipbreaker
Chamfering Surfacing
90°
M00000500.80 Neutral3.1812.7SPUN 120308 LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
SPUN
MILLING
318
Machining Conditions
SPUN 120308 – LT 30
min max min max min max D.O.C. Feed
1 125 HB 0.5 7.0 0.18 0.37 190 330 33.0 00.26 2250
2 190 HB 0.5 7.0 0.18 0.37 190 300 33.0 00.26 2220
3 250 HB 0.5 7.0 0.18 0.37 190 250 33.0 00.26 2200
6 180 HB 0.5 7.0 0.15 0.29 150 240 33.0 00.23 2200
4,6 230 HB 0.5 7.0 0.15 0.29 150 210 33.0 00.23 1180
5,7 280 HB 0.5 7.0 0.15 0.25 130 190 33.0 00.21 1150
8 350 HB 0.5 7.0 0.15 0.25 130 170 33.0 00.21 1140
10 220 HB 0.5 5.0 0.12 0.25 90 150 22.3 00.21 1130
10 280 HB 0.5 5.0 0.12 0.25 90 130 22.3 00.21 1120
11 320 HB 0.5 5.0 0.12 0.21 60 110 22.3 00.18 1100
11 350 HB 0.5 5.0 0.12 0.21 60 90 22.3 00.18 880
15 150 HB 0.5 7.0 0.18 0.37 150 240 33.0 00.26 2200
15 200 HB 0.5 7.0 0.18 0.37 150 220 33.0 00.26 1180
16 250 HB 0.5 7.0 0.18 0.37 150 190 33.0 00.26 1160
17,19 150 HB 0.5 7.0 0.15 0.32 100 200 33.0 00.23 1180
17,19 200 HB 0.5 7.0 0.15 0.32 100 180 33.0 00.23 1150
18,20 250 HB 0.5 7.0 0.15 0.32 100 150 33.0 00.23 1130
38 45 HRc 0.5 2.5 0.10 0.21 40 80 11.5 00.16 660
38 50 HRc 0.5 1.8 0.10 0.18 40 70 11.1 00.15 555
38 55 HRc 0.5 1.5 0.10 0.16 40 60 00.8 00.14 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 2.0 0.10 0.21 40 80 11.1 00.16 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.16 30 60 00.8 00.14 440
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Cast
Iron
Grey
Malleable & Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
319
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
T P K N
Shape Clearance Angle Tolerance
11°
Fixing,Chipbreaker
60°
m ± 0.013 s ± 0.025For l = 16, d ± 0.05For l = 22, d ± 0.08
sl
mØ d
Shoulder Milling SurfacingSlotting
11°60°
M0000052
M0000051
1.20
1.20
Right
Right
4.76
3.18
19.92
14.52
TPKN 2204 PDTR LT 30
TPKN 1603 PDTR LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
TPKN
MILLING
320
Cutters
Shell Mill for TPKN 1603 PDTR
Cutter Designation
LT 310 M-D-D080/5*
LT 310 M-D-D063/4*
LT 310 M-D-D100/6*
LT 310 M-D-D125/6*
Catalog Nr.
M2000700
M2000699
M2000701
M2000702
D
80
63
100
125
z
5
4
6
6
Ap
13
13
13
13
d
27
22
32
40
L
50
50
50
63
D
d
Ap
L
90°
Shell Mill for TPKN 2204 PDTR
Cutter Designation
LT 320 M-D-D100/5*
LT 320 M-D-D080/4*
LT 320 M-D-D125/6*
LT 320 M-D-D160/7*
Catalog Nr.
M2000704
M2000703
M2000705
M2000706
D
100
80
125
160
z
5
4
6
7
Ap
18
18
18
18
d
32
27
40
40
L
50
50
63
63
* On request
* On request
Screw:Key:
M2002952M2000609
Screw:Key:
M2002951M2000609
MILLING
321
Machining Conditions
TPKN 1603 PDTR – LT 30
min max min max min max D.O.C. Feed
1 125 HB 0.5 12.0 0.14 0.27 190 330 33.0 0.20 2250
2 190 HB 0.5 12.0 0.14 0.27 190 300 33.0 0.20 2220
3 250 HB 0.5 12.0 0.14 0.27 190 250 33.0 0.20 2200
6 180 HB 0.5 12.0 0.12 0.21 150 240 33.0 0.17 2200
4,6 230 HB 0.5 12.0 0.12 0.21 150 210 33.0 0.17 1180
5,7 280 HB 0.5 12.0 0.12 0.19 130 190 33.0 0.15 1150
8 350 HB 0.5 12.0 0.12 0.19 130 170 33.0 0.15 1140
10 220 HB 0.5 8.6 0.10 0.19 90 150 22.3 0.15 1130
10 280 HB 0.5 8.6 0.10 0.19 90 130 22.3 0.15 1120
11 320 HB 0.5 8.6 0.10 0.15 60 110 22.3 0.14 1100
11 350 HB 0.5 8.6 0.10 0.15 60 90 22.3 0.14 880
15 150 HB 0.5 12.0 0.14 0.27 150 240 33.0 0.20 2200
15 200 HB 0.5 12.0 0.14 0.27 150 220 33.0 0.20 1180
16 250 HB 0.5 12.0 0.14 0.27 150 190 33.0 0.20 1160
17,19 150 HB 0.5 12.0 0.12 0.24 100 200 33.0 0.17 1180
17,19 200 HB 0.5 12.0 0.12 0.24 100 180 33.0 0.17 1150
18,20 250 HB 0.5 12.0 0.12 0.24 100 150 33.0 0.17 1130
38 45 HRc 0.5 4.3 0.08 0.15 40 80 11.5 0.12 660
38 50 HRc 0.5 3.0 0.08 0.14 40 70 11.1 0.11 555
38 55 HRc 0.5 2.6 0.08 0.12 40 60 00.8 0.10 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 3.4 0.08 0.15 40 80 11.1 0.12 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 2.6 0.08 0.12 30 60 00.8 0.10 440
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Cast
Iron
Grey
Malleable & Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
MILLING
322
Machining Conditions
TPKN 2204 PDTR – LT 30
min max min max min max D.O.C. Feed
1 125 HB 0.5 18.0 0.16 0.27 190 330 44.0 00.19 2250
2 190 HB 0.5 18.0 0.16 0.27 190 300 44.0 00.19 2220
3 250 HB 0.5 18.0 0.16 0.27 190 250 44.0 00.19 2200
6 180 HB 0.5 18.0 0.14 0.21 150 240 44.0 00.17 2200
4,6 230 HB 0.5 18.0 0.14 0.21 150 210 44.0 00.17 1180
5,7 280 HB 0.5 18.0 0.14 0.19 130 190 44.0 00.15 1150
8 350 HB 0.5 18.0 0.14 0.19 130 170 44.0 00.15 1140
10 220 HB 0.5 12.9 0.11 0.19 90 150 33.0 00.15 1130
10 280 HB 0.5 12.9 0.11 0.19 90 130 33.0 00.15 1120
11 320 HB 0.5 12.9 0.11 0.15 60 110 33.0 00.13 1100
11 350 HB 0.5 12.9 0.11 0.15 60 90 33.0 00.13 880
15 150 HB 0.5 18.0 0.16 0.27 150 240 44.0 00.19 2200
15 200 HB 0.5 18.0 0.16 0.27 150 220 44.0 00.19 1180
16 250 HB 0.5 18.0 0.16 0.27 150 190 44.0 00.19 1160
17,19 150 HB 0.5 18.0 0.14 0.24 100 200 44.0 00.17 1180
17,19 200 HB 0.5 18.0 0.14 0.24 100 180 44.0 00.17 1150
18,20 250 HB 0.5 18.0 0.14 0.24 100 150 44.0 00.17 1130
38 45 HRc 0.5 6.4 0.09 0.15 40 80 22.0 00.12 660
38 50 HRc 0.5 4.5 0.09 0.14 40 70 11.5 00.11 555
38 55 HRc 0.5 3.9 0.09 0.12 40 60 11.0 00.10 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 5.1 0.09 0.15 40 80 11.5 00.12 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 3.9 0.09 0.12 30 60 11.0 00.10 440
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Cast
Iron
Grey
Malleable & Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
323
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
T P K R
Shape Clearance Angle Tolerance
11°
Fixing,Chipbreaker
s
60°
m ± 0.013 s ± 0.025For l = 16, d ± 0.05For l = 22, d ± 0.08
l
mØ d
Shoulder Milling SurfacingSlotting
1160°
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
M0000983
M0000053
1.20
1.20
Right
Right
4.76
3.18
19.92
14.52
TPKR 2204 PDTR LT 30
TPKR 1603 PDTR LT 30
TPKR
MILLING
324
Cutters
Shell Mill for TPKR 1603 PDTR
Cutter Designation
LT 310 M-D-D080/5*
LT 310 M-D-D063/4*
LT 310 M-D-D100/6*
LT 310 M-D-D125/6*
Catalog Nr.
M2000700
M2000699
M2000701
M2000702
D
80
63
100
125
z
5
4
6
6
Ap
13
13
13
13
d
27
22
32
40
L
50
50
50
63
D
d
Ap
L
90°
D
d
9
Shell Mill for TPKR 2204 PDTR
Cutter Designation
LT 320 M-D-D100/5*
LT 320 M-D-D080/4*
LT 320 M-D-D125/6*
LT 320 M-D-D160/7*
Catalog Nr.
M2000704
M2000703
M2000705
M2000706
D
100
80
125
160
z
5
4
6
7
Ap
18
18
18
18
d
32
27
40
40
L
50
50
63
63
* On request
* On request
Screw:Key:
M2002952M2000609
Screw:Key:
M2002951M2000609
MILLING
325
Machining Conditions
TPKR 1603 PDTR – LT 30
min max min max min max D.O.C. Feed
1 125 HB 0.5 12.0 0.13 0.22 190 330 33.0 0.17 2250
2 190 HB 0.5 12.0 0.13 0.22 190 300 33.0 0.17 2220
3 250 HB 0.5 12.0 0.13 0.22 190 250 33.0 0.17 2200
6 180 HB 0.5 12.0 0.11 0.18 150 240 33.0 0.15 2200
4,6 230 HB 0.5 12.0 0.11 0.18 150 210 33.0 0.15 1180
5,7 280 HB 0.5 12.0 0.11 0.15 130 190 33.0 0.13 1150
8 350 HB 0.5 12.0 0.11 0.15 130 170 33.0 0.13 1140
10 220 HB 0.5 8.6 0.08 0.15 90 150 22.3 0.13 1130
10 280 HB 0.5 8.6 0.08 0.15 90 130 22.3 0.13 1120
11 320 HB 0.5 8.6 0.08 0.13 60 110 22.3 0.12 1100
11 350 HB 0.5 8.6 0.08 0.13 60 90 22.3 0.12 880
14 180 HB 0.5 12.0 0.11 0.15 190 250 33.0 0.13 2220
14 240 HB 0.5 12.0 0.08 0.14 160 210 33.0 0.13 1190
14 290 HB 0.5 8.6 0.08 0.13 70 130 22.3 0.12 1100
14 310 HB 0.5 8.6 0.08 0.13 70 120 22.3 0.12 990
12 200 HB 0.5 12.0 0.11 0.15 150 210 33.0 0.13 1190
13 42 HRc 0.5 8.6 0.11 0.13 90 150 22.3 0.12 1130
15 150 HB 0.5 12.0 0.13 0.22 150 240 33.0 0.17 2200
15 200 HB 0.5 12.0 0.13 0.22 150 220 33.0 0.17 1180
16 250 HB 0.5 12.0 0.13 0.22 150 190 33.0 0.17 1160
17,19 150 HB 0.5 12.0 0.11 0.20 100 200 33.0 0.15 1180
17,19 200 HB 0.5 12.0 0.11 0.20 100 180 33.0 0.15 1150
18,20 250 HB 0.5 12.0 0.11 0.20 100 150 33.0 0.15 1130
31,32 Incoloy 800 240 HB 0.5 8.6 0.08 0.13 25 45 22.3 0.12 332
33 Inconel 700 250 HB 0.5 8.6 0.08 0.13 25 45 22.3 0.12 330
34 Stellite 21 350 HB 0.5 8.6 0.08 0.13 25 45 22.3 0.12 330
36 TiAl6V4 - 0.5 8.6 0.08 0.14 40 65 22.3 0.13 555
37 T40 - 0.5 8.6 0.08 0.13 30 55 22.3 0.12 440
38 45 HRc 0.5 4.3 0.07 0.13 40 80 11.5 0.10 660
38 50 HRc 0.5 3.0 0.07 0.11 40 70 11.1 0.09 555
38 55 HRc 0.5 2.6 0.07 0.10 40 60 00.8 0.09 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 3.4 0.07 0.13 40 80 11.1 0.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 2.6 0.07 0.10 30 60 00.8 0.09 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 12.0 0.13 0.22 200 400 3.0 0.18 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N°VDI
GroupMaterial
ExemplesHardness
D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting
Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non-alloyed
Stee
l Low alloyed
High Alloyed
Stai
nles
s St
eel High Alloyed
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co based
Ti based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
MILLING
326
Machining Conditions
TPKR 2204 PDTR – LT 30
min max min max min max D.O.C. Feed
1 125 HB 0.5 18.0 0.13 0.22 190 330 44.0 00.17 2250
2 190 HB 0.5 18.0 0.13 0.22 190 300 44.0 00.17 2220
3 250 HB 0.5 18.0 0.13 0.22 190 250 44.0 00.17 2200
6 180 HB 0.5 18.0 0.11 0.18 150 240 44.0 00.15 2200
4,6 230 HB 0.5 18.0 0.11 0.18 150 210 44.0 00.15 1180
5,7 280 HB 0.5 18.0 0.11 0.15 130 190 44.0 00.13 1150
8 350 HB 0.5 18.0 0.11 0.15 130 170 44.0 00.13 1140
10 220 HB 0.5 12.9 0.08 0.15 90 150 33.0 00.13 1130
10 280 HB 0.5 12.9 0.08 0.15 90 130 33.0 00.13 1120
11 320 HB 0.5 12.9 0.08 0.13 60 110 33.0 00.12 1100
11 350 HB 0.5 12.9 0.08 0.13 60 90 33.0 00.12 880
14 180 HB 0.5 18.0 0.11 0.15 190 250 44.0 00.13 2220
14 240 HB 0.5 18.0 0.08 0.14 160 210 44.0 00.13 1190
14 290 HB 0.5 12.9 0.08 0.13 70 130 33.0 00.12 1100
14 310 HB 0.5 12.9 0.08 0.13 70 120 33.0 00.12 990
12 200 HB 0.5 18.0 0.11 0.15 150 210 44.0 00.13 1190
13 42 HRc 0.5 12.9 0.11 0.13 90 150 33.0 00.12 1130
15 150 HB 0.5 18.0 0.13 0.22 150 240 44.0 00.17 2200
15 200 HB 0.5 18.0 0.13 0.22 150 220 44.0 00.17 1180
16 250 HB 0.5 18.0 0.13 0.22 150 190 44.0 00.17 1160
17,19 150 HB 0.5 18.0 0.11 0.20 100 200 44.0 00.15 1180
17,19 200 HB 0.5 18.0 0.11 0.20 100 180 44.0 00.15 1150
18,20 250 HB 0.5 18.0 0.11 0.20 100 150 44.0 00.15 1130
31,32 Incoloy 800 240 HB 0.5 12.9 0.08 0.13 25 45 33.0 00.12 332
33 Inconel 700 250 HB 0.5 12.9 0.08 0.13 25 45 33.0 00.12 330
34 Stellite 21 350 HB 0.5 12.9 0.08 0.13 25 45 33.0 00.12 330
36 TiAl6V4 - 0.5 12.9 0.08 0.14 40 65 33.0 00.13 555
37 T40 - 0.5 12.9 0.08 0.13 30 55 33.0 00.12 440
38 45 HRc 0.5 6.4 0.07 0.13 40 80 22.0 00.10 660
38 50 HRc 0.5 4.5 0.07 0.11 40 70 11.5 00.09 555
38 55 HRc 0.5 3.9 0.07 0.10 40 60 11.0 00.09 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 5.1 0.07 0.13 40 80 11.5 00.10 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 3.9 0.07 0.10 30 60 11.0 00.09 440
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 18.0 0.13 0.22 200 400 4.0 0.18 280
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
327
MILLING
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
T P U N
Shape Clearance Angled ± 0.08m ± 0.13s ± 0.13
Tolerance
11°
sl
mØ d
Fixing,Chipbreaker
60°
Shoulder Milling SurfacingSlotting
11°60°
M00000540.80 Right3.1813.49TPUN 160308 LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
TPUN
MILLING
328
Cutters
Shell Mill for TPUN1603 PDTR
Cutter Designation
LT 310 M-D-D100/6*
LT 310 M-D-D125/6*
Catalog Nr.
M2000700
M2000699
M2000701
M2000702
LT 310 M-D-D080/5*
LT 310 M-D-D063/4*
D
80
63
100
125
z
5
4
6
6
Ap
13
13
13
13
d
27
22
32
40
L
50
50
50
63
D
d
Ap
L
90°
* On request Screw:Key:
M2002951M2000609
MILLING
329
Machining Conditions
TPUN 160308 NN PDTR – LT 30
min max min max min max D.O.C. Feed
1 125 HB 0.5 12.0 0.14 0.27 190 330 33.0 0.20 2250
2 190 HB 0.5 12.0 0.14 0.27 190 300 33.0 0.20 2220
3 250 HB 0.5 12.0 0.14 0.27 190 250 33.0 0.20 2200
6 180 HB 0.5 12.0 0.12 0.21 150 240 33.0 0.17 2200
4,6 230 HB 0.5 12.0 0.12 0.21 150 210 33.0 0.17 1180
5,7 280 HB 0.5 12.0 0.12 0.19 130 190 33.0 0.15 1150
8 350 HB 0.5 12.0 0.12 0.19 130 170 33.0 0.15 1140
10 220 HB 0.5 8.6 0.10 0.19 90 150 22.3 0.15 1130
10 280 HB 0.5 8.6 0.10 0.19 90 130 22.3 0.15 1120
11 320 HB 0.5 8.6 0.10 0.15 60 110 22.3 0.14 1100
11 350 HB 0.5 8.6 0.10 0.15 60 90 22.3 0.14 880
15 150 HB 0.5 12.0 0.14 0.27 150 240 33.0 0.20 2200
15 200 HB 0.5 12.0 0.14 0.27 150 220 33.0 0.20 1180
16 250 HB 0.5 12.0 0.14 0.27 150 190 33.0 0.20 1160
17,19 150 HB 0.5 12.0 0.12 0.24 100 200 33.0 0.17 1180
17,19 200 HB 0.5 12.0 0.12 0.24 100 180 33.0 0.17 1150
18,20 250 HB 0.5 12.0 0.12 0.24 100 150 33.0 0.17 1130
38 45 HRc 0.5 4.3 0.08 0.15 40 80 11.5 0.12 660
38 50 HRc 0.5 3.0 0.08 0.14 40 70 11.1 0.11 555
38 55 HRc 0.5 2.6 0.08 0.12 40 60 00.8 0.10 550
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 3.4 0.08 0.15 40 80 11.1 0.12 550
White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 2.6 0.08 0.12 30 60 00.8 0.10 440
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
8
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Cast
Iron
Grey
Malleable & Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
ALU-MILLING
330
ALU-MILLING
331
Machining Conditions
LT 05ALU-MILLING
APGT
ALU-MILLING
332
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
A P G T11°
Shape Clearance Angle Fixing,Chipbreaker
l
d ± 0.025m ± 0.025s ± 0.13
Ø d
s
m
Tolerance
Shoulder Mill SurfacingSlotting
M0003089
M0001010
0.40
0.80
Right
Right
3.52
4.89
10.80
16.40
APGT 100304 PDER-ALU LT05
APGT 160408 PDER-ALU LT05
Insert Designation Catalog Nr.Directions rl
LT 05
ALU-MILLING
333
Machining Conditions
APGT 100304 PDER-ALU – LT 05
APGT 160408 PDER-ALU – LT 05
min max min max min max D.O.C Feed
Si < 4 % 60 HB 0.3 9.0 0.12 0.20 400 1200 33.0 0.14 5500
4% < Si < 8 % 100 HB 0.3 9.0 0.10 0.18 250 600 33.0 0.14 4400
Copper Alloys 14 26,27,28 CuZn30 100 HB 0.3 9.0 0.10 0.18 100 800 33.0 0.14 3300
29 Fiber Plastics - 0.3 9.0 0.12 0.20 80 500 33.0 0.12 2200
30 Hard Rubber - 0.3 9.0 0.12 0.20 80 300 33.0 0.12 1150
- Graphite - 0.3 9.0 0.12 0.20 100 200 33.0 0.12 1150
36 Ti 1 - 0.3 5.0 0.08 0.20 35 60 22.0 0.12 445
37 TiAl 6 V4 - 0.3 5.0 0.08 0.15 28 45 22.0 0.12 335
15
10
1321, 22 23, 24
min max min max min max D.O.C Feed
Si < 4 % 60 HB 0.5 15.0 0.15 0.32 400 1200 44.0 0.16 5500
4% < Si < 8 % 100 HB 0.5 15.0 0.13 0.29 250 600 44.0 0.16 4400
Copper Alloys 14 26,27,28 CuZn30 100 HB 0.5 15.0 0.13 0.29 100 800 44.0 0.16 3300
29 Fiber Plastics - 0.5 15.0 0.15 0.32 80 500 44.0 0.14 2200
30 Hard Rubber - 0.5 15.0 0.15 0.32 80 300 44.0 0.14 1150
- Graphite - 0.5 15.0 0.15 0.32 100 200 44.0 0.14 1150
36 Ti 1 - 0.5 15.0 0.10 0.32 35 60 44.0 0.14 445
37 TiAl 6 V4 - 0.5 15.0 0.10 0.24 28 45 44.0 0.14 335
15
10
1321, 22 23, 24
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
H.T.
A
Ti Based Alloys
NF
Al (<8%Si)
Copper Alloys
Non-Metallic
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
H.T.
A
Ti Based Alloys
NF
Al (<8%Si)
Copper Alloys
Non-Metallic
ALU-MILLING
334
FProductivity
1, 2, 3, 46, 7, 8, 1110, 125, 9
NoNoYesYesCoolant
Stainless Steel
VC
Application Guide MachiningRecommendations
S E G T
Shape Clearance Angles
d ± 0.025m ± 0.025s ± 0.13
90° 20°l
mØ d
Fixing,Chipbreaker
Tolerance
Surfacing
ALU-MILLING
90°
M00010080.84 Neutral4.7912.70SEGT 1204 AFEN-ALU LT05
Insert Designation Catalog Nr.Directions rl
LT 05
Chamfering
ALU-MILLING
335
Machining Conditions
SEGT 1204 AFEN-ALU – LT 05
min max min max min max D.O.C Feed
Si < 4 % 60 HB 0.3 9.0 0.12 0.35 400 1200 33.0 0.25 5500
4% < Si < 8 % 100 HB 0.3 9.0 0.10 0.35 250 600 33.0 0.25 4400
Cooper Alloys 14 26,27,28 CuZn30 100 HB 0.3 9.0 0.10 0.35 100 800 33.0 0.25 3300
29 Fiber Plastics - 0.3 9.0 0.12 0.35 80 500 33.0 0.20 2200
30 Hard Rubber - 0.3 9.0 0.12 0.35 80 300 33.0 0.20 1150
- Graphite - 0.3 9.0 0.12 0.35 100 200 33.0 0.20 1150
36 Ti 1 - 0.3 5.0 0.08 0.35 35 60 22.0 0.20 445
37 TiAl 6 V4 - 0.3 5.0 0.08 0.28 28 45 22.0 0.20 335
1321, 22 23, 24
15
10
SEGT
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters
min max min max min max D.O.C Feed Vc
H.T.
A
Ti Based Alloys
NF
Al (<8%Si)
Copper Alloys
Non-Metallic
336
DRILLING
337
DRILLING
LT 30DRILLING
SPMG
338
DRILLING
S P M Gl
Shape Clearance Angle
11°
Tolerance d ± 0.05m ± 0.08s ± 0.13
90° Ø dm
Fixing,Chipbreaker
s
M3003882
M3002914
M3003883
M3002913
M3002915
0.40
0.80
0.80
0.40
0.80
Neutral
Neutral
Neutral
Neutral
Neutral
2.38
3.97
4.76
2.38
4.76
5.0
7.94
11.50
6.0
9.80
SPMG 050204 NN LT 30
SPMG 07T308 NN LT 30
SPMG 110408 NN LT 30
SPMG 060204 NN LT 30
SPMG 090408 NN LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
339
DRILLING
108
110
113
113
115
115
119
121
32
34
36
36
38
38
40
42
M2003247
M2003248
M2003695
M2003249
M2003696
M2003250
M2003251
M2003252
124
127
131
131
134
134
139
142
48
51
54
54
57
57
60
63
M2003266
M2003267
M2003700
M2003268
M2003701
M2003269
M2003270
M2003271
94
L
L
L
94
96
96
99
99
26
L1
L1
L1
26
28
28
30
30
M2003704
Catalog Nr
Catalog Nr
Catalog Nr
M2003705
M2003706
M2003707
M2003708
M2003709
2xD
2xD
2xD
107 39 M2003718
L
L
L
L1
L1
L1
Catalog Nr
Catalog Nr
Catalog Nr
107 39 M2003719
110 42 M2003720
110 42 M2003721
114 45 M2003722
114 45 M2003723
3xD
3xD
3xD
123
131
134
137
139
141
141
44
46
48
50
52
54
54
M2003253
M2003255
M2003256
M2003257
M2003258
M2003698
M2003259
145
154
158
162
165
168
168
66
69
72
75
78
81
81
M2003272
M2003273
M2003274
M2003275
M2003276
M2003702
M2003277
LT DR160 S06-_D 16.0 25
LT DR170 S06-_D 17.0 25
LT DR175 S06-_D 17.5 25
LT DR180 S06-_D 18.0 25
LT DR185 S06-_D 18.5 25
LT DR190 S06-_D 19.0 25
LT DR200 S06-_D 20.0 25
LT DR210 S06-_D 21.0 25
Insert SPMG 060204
LT DR125 S05-_D
Drill Body Designation
Drill Body Designation
Drill Body Designation
LT DR130 S05-_D
LT DR135 S05-_D
LT DR140 S05-_D
LT DR145 S05-_D
LT DR150 S05-_D
12.5
D
D
D
13.0
13.5
14.0
14.5
15.0
20
d
d
d
20
20
20
20
20
Insert SPMG 050204 **
LT DR220 S07-_D
LT DR230 S07-_D
LT DR240 S07-_D
LT DR250 S07-_D
LT DR260 S07-_D
LT DR265 S07-_D
LT DR270 S07-_D
22.0
23.0
24.0
25.0
26.0
26.5
27.0
25
32
32
32
32
32
32
Insert SPMG 07T308
Screw: M2003824
Screw: M2003823
Screw: M2003820
** 4D for SPMG 050204 and 110408 also available on request
D
L1
L
d D
L1
340
DRILLING
Drill Body Designation D d
Insert SPMG 110408 **
LT DR350 S11-_D
LT DR360 S11-_D
LT DR370 S11-_D
LT DR380 S11-_D
LT DR390 S11-_D
LT DR400 S11-_D
LT DR410 S11-_D
LT DR340 S11-_D
35.0
36.0
37.0
38.0
39.0
40.0
41.0
34.0
40
40
40
40
40
40
40
40
L L1 Catalog Nr
174
177
180
183
185
188
191
171
70
72
74
76
78
80
82
68
M2003711
M2003712
M2003713
M2003714
M2003715
M2003716
M2003717
M2003710
L L1 Catalog Nr
209
213
217
221
224
228
232
105
108
111
114
117
120
123
M2003725
M2003726
M2003727
M2003728
M2003729
M2003730
M2003731
205 102 M2003724
Drill Body Designation D d L L1 Catalog Nr
2xD
2xD*
L L1 Catalog Nr
3xD
3xD
LT DR280 S09-_D
LT DR290 S09-_D
LT DR295 S09-_D
LT DR300 S09-_D
LT DR310 S09-_D
LT DR320 S09-_D
LT DR330 S09-_D
28.0
29.0
29.5
30.0
31.0
32.0
33.0
32
32
32
32
32
32
32
144
146
151
151
154
156
159
56
58
60
60
62
64
66
M2003260
M2003261
M2003699
M2003262
M2003263
M2003264
M2003265
172
175
181
181
185
188
192
84
87
90
90
93
96
99
M2003278
M2003280
M2003703
M2003281
M2003282
M2003283
M2003284
Insert SPMG 090408
Screw: M2003821
* Available on request** 4D for SPMG 050204 and 110408 also available on request
D
L1
L
d D
L1
Screw: M2003822
341
DRILLINGMachining Conditions
SPMG 050204 NN – LT 30
min max min max Feed
1 125 HB 0.04 0.09 180 270 00.07 225
2 190 HB 0.04 0.09 180 230 00.07 205
3 250 HB 0.04 0.09 180 200 00.07 190
6 180 HB 0.04 0.09 120 230 00.07 175
4,6 230 HB 0.04 0.09 120 190 00.05 155
5,7 280 HB 0.04 0.09 100 170 00.04 135
8 350 HB 0.04 0.09 100 150 00.04 125
10 220 HB 0.05 0.09 70 170 00.07 120
10 280 HB 0.05 0.09 70 150 00.07 110
11 320 HB 0.05 0.08 60 130 00.07 95
11 350 HB 0.05 0.08 60 100 00.07 80
14 180 HB 0.04 0.09 170 230 00.06 200
14 240 HB 0.05 0.09 120 210 00.07 165
14 290 HB 0.05 0.08 70 120 00.07 95
14 310 HB 0.05 0.08 70 120 00.07 95
12 200 HB 0.05 0.08 100 150 00.07 125
13 42 HRc 0.04 0.07 60 100 00.05 80
15 150 HB 0.07 0.09 150 230 00.08 190
15 200 HB 0.07 0.09 150 210 00.08 180
16 250 HB 0.07 0.09 150 170 00.08 160
17,19 150 HB 0.07 0.09 120 200 00.08 160
17,19 200 HB 0.07 0.09 120 170 00.08 145
18,20 250 HB 0.07 0.09 120 150 00.08 135
31,32 Incoloy 800 240 HB 0.04 0.07 25 35 00.05 30
33 Inconel 700 250 HB 0.04 0.07 25 35 00.05 30
34 Stellite 21 350 HB 0.04 0.07 23 35 00.07 29
36 TiAl6V4 - 0.04 0.07 35 60 00.05 48
37 T40 - 0.04 0.07 28 40 00.05 34
38 45 HRc 0.04 0.07 50 90 00.05 70
38 50 HRc 0.04 0.07 40 70 00.05 55
38 55 HRc 0.04 0.07 30 60 00.05 45
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.04 0.07 40 60 00.05 50
White Cast Iron 41 G-X300CrMo15 55 HRc 0.04 0.07 30 50 00.05 40
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.04 0.09 200 400 00.07 300
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]
min max min max min maxMaterial Group Gr. N° VDI
GroupMaterial Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
342
DRILLING
342
Machining Conditions
SPMG 060204 NN – LT 30
min max min max Feed
1 125 HB 0.04 0.09 180 270 00.07 225
2 190 HB 0.04 0.09 180 230 00.07 205
3 250 HB 0.04 0.09 180 200 00.07 190
6 180 HB 0.04 0.09 120 230 00.07 175
4,6 230 HB 0.04 0.09 120 190 00.07 155
5,7 280 HB 0.04 0.09 100 170 00.06 135
8 350 HB 0.04 0.09 100 150 00.06 125
10 220 HB 0.05 0.09 70 170 00.07 120
10 280 HB 0.05 0.09 70 150 00.07 110
11 320 HB 0.05 0.08 60 130 00.07 95
11 350 HB 0.05 0.08 60 100 00.07 80
14 180 HB 0.04 0.09 170 230 00.06 200
14 240 HB 0.05 0.09 120 210 00.07 165
14 290 HB 0.05 0.08 70 120 00.07 95
14 310 HB 0.05 0.08 70 120 00.07 95
12 200 HB 0.05 0.08 100 150 00.07 125
13 42 HRc 0.04 0.07 60 100 00.05 80
15 150 HB 0.07 0.10 150 230 00.09 190
15 200 HB 0.07 0.10 150 210 00.09 180
16 250 HB 0.07 0.10 150 170 00.09 160
17,19 150 HB 0.07 0.10 120 200 00.09 160
17,19 200 HB 0.07 0.10 120 170 00.09 145
18,20 250 HB 0.07 0.10 120 150 00.09 135
31,32 Incoloy 800 240 HB 0.04 0.07 25 35 00.05 30
33 Inconel 700 250 HB 0.04 0.07 25 35 00.05 30
34 Stellite 21 350 HB 0.04 0.07 23 35 00.05 29
36 TiAl6V4 - 0.04 0.07 35 60 00.05 45
37 T40 - 0.04 0.07 28 40 00.05 34
38 45 HRc 0.04 0.07 50 90 00.05 70
38 50 HRc 0.04 0.07 40 70 00.05 55
38 55 HRc 0.04 0.07 30 60 00.05 45
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.04 0.07 40 60 00.05 50
White Cast Iron 41 G-X300CrMo15 55 HRc 0.04 0.07 30 50 00.05 40
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.04 0.09 200 400 00.07 300
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]
min max min max min maxMaterial Group Gr. N° VDI
GroupMaterial Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
343
DRILLINGMachining Conditions
SPMG 07T308 NN – LT 30
min max min max Feed
1 125 HB 0.05 0.10 180 270 00.08 225
2 190 HB 0.05 0.10 180 230 00.08 205
3 250 HB 0.05 0.10 180 200 00.08 190
6 180 HB 0.05 0.10 120 230 00.08 175
4,6 230 HB 0.05 0.10 120 190 00.08 155
5,7 280 HB 0.05 0.10 100 170 00.07 135
8 350 HB 0.05 0.10 100 150 00.07 125
10 220 HB 0.07 0.10 70 170 00.09 120
10 280 HB 0.07 0.10 70 150 00.09 110
11 320 HB 0.07 0.09 60 130 00.08 95
11 350 HB 0.07 0.09 60 100 00.08 80
14 180 HB 0.05 0.10 170 230 00.07 200
14 240 HB 0.07 0.10 120 210 00.08 165
14 290 HB 0.07 0.09 70 120 00.08 95
14 310 HB 0.07 0.09 70 120 00.08 95
12 200 HB 0.07 0.09 100 150 00.08 125
13 42 HRc 0.05 0.08 60 100 00.07 80
15 150 HB 0.10 0.11 150 230 00.11 190
15 200 HB 0.10 0.11 150 210 00.11 180
16 250 HB 0.10 0.11 150 170 00.11 160
17,19 150 HB 0.10 0.11 120 200 00.11 160
17,19 200 HB 0.10 0.11 120 170 00.11 145
18,20 250 HB 0.10 0.11 120 150 00.11 135
31,32 Incoloy 800 240 HB 0.05 0.08 25 35 00.07 30
33 Inconel 700 250 HB 0.05 0.08 25 35 00.07 30
34 Stellite 21 350 HB 0.05 0.08 23 35 00.07 29
36 TiAl6V4 - 0.05 0.08 35 60 00.07 45
37 T40 - 0.05 0.08 28 40 00.07 34
38 45 HRc 0.05 0.08 50 90 00.07 70
38 50 HRc 0.05 0.08 40 70 00.07 55
38 55 HRc 0.05 0.08 30 60 00.07 45
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.05 0.08 40 60 00.07 50
White Cast Iron 41 G-X300CrMo15 55 HRc 0.05 0.08 30 50 00.07 40
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.05 0.10 200 400 00.08 300
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]
min max min max min maxMaterial Group Gr. N° VDI
GroupMaterial Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
344
DRILLING
344
Machining Conditions
SPMG 090408 NN – LT 30
min max min max Feed
1 125 HB 0.06 0.11 180 270 00.09 225
2 190 HB 0.06 0.11 180 230 00.09 205
3 250 HB 0.06 0.11 180 200 00.09 190
6 180 HB 0.06 0.11 120 230 00.09 175
4,6 230 HB 0.06 0.11 120 190 00.09 155
5,7 280 HB 0.06 0.11 100 170 00.08 135
8 350 HB 0.06 0.11 100 150 00.08 125
10 220 HB 0.09 0.11 70 170 00.10 120
10 280 HB 0.09 0.11 70 150 00.10 110
11 320 HB 0.09 0.10 60 130 00.09 95
11 350 HB 0.09 0.10 60 100 00.09 80
14 180 HB 0.06 0.11 170 230 00.08 200
14 240 HB 0.09 0.11 120 210 00.10 165
14 290 HB 0.09 0.10 70 120 00.09 95
14 310 HB 0.09 0.10 70 120 00.09 95
12 200 HB 0.09 0.10 100 150 00.09 125
13 42 HRc 0.06 0.09 60 100 00.08 80
15 150 HB 0.10 0.12 150 230 00.11 190
15 200 HB 0.10 0.12 150 210 00.11 180
16 250 HB 0.10 0.12 150 170 00.11 160
17,19 150 HB 0.10 0.12 120 200 00.11 160
17,19 200 HB 0.10 0.12 120 170 00.11 145
18,20 250 HB 0.10 0.12 120 150 00.11 135
31,32 Incoloy 800 240 HB 0.06 0.09 25 35 00.08 30
33 Inconel 700 250 HB 0.06 0.09 25 35 00.08 30
34 Stellite 21 350 HB 0.06 0.09 23 35 00.08 29
36 TiAl6V4 - 0.06 0.09 35 60 00.08 45
37 T40 - 0.06 0.09 28 40 00.08 34
38 45 HRc 0.06 0.09 50 90 00.08 70
38 50 HRc 0.06 0.09 40 70 00.08 55
38 55 HRc 0.06 0.09 30 60 00.08 45
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.06 0.09 40 60 00.08 50
White Cast Iron 41 G-X300CrMo15 55 HRc 0.06 0.09 30 50 00.08 40
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.06 0.11 200 400 00.09 300
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]
min max min max min maxMaterial Group Gr. N° VDI
GroupMaterial Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
345
DRILLINGMachining Conditions
SPMG 110408 NN – LT 30
min max min max Feed
1 125 HB 0.08 0.14 180 270 00.11 225
2 190 HB 0.08 0.14 180 230 00.11 205
3 250 HB 0.08 0.14 180 200 00.11 190
6 180 HB 0.07 0.14 120 230 00.11 175
4,6 230 HB 0.07 0.14 120 190 00.07 155
5,7 280 HB 0.07 0.14 100 170 00.07 135
8 350 HB 0.07 0.12 100 150 00.07 125
10 220 HB 0.07 0.12 70 170 00.10 120
10 280 HB 0.07 0.12 70 150 00.10 110
11 320 HB 0.07 0.11 60 130 00.09 95
11 350 HB 0.07 0.10 60 100 00.08 80
14 180 HB 0.06 0.11 170 230 00.08 200
14 240 HB 0.09 0.11 120 210 00.10 165
14 290 HB 0.06 0.10 70 120 00.08 95
14 310 HB 0.06 0.09 70 120 00.08 95
12 200 HB 0.09 0.10 100 150 00.09 125
13 42 HRc 0.06 0.09 60 100 00.08 80
15 150 HB 0.10 0.15 150 230 00.13 190
15 200 HB 0.10 0.15 150 210 00.13 180
16 250 HB 0.10 0.15 150 170 00.13 160
17,19 150 HB 0.10 0.15 120 200 00.13 160
17,19 200 HB 0.10 0.14 120 170 00.12 145
18,20 250 HB 0.10 0.14 120 150 00.12 135
31,32 Incoloy 800 240 HB 0.06 0.10 25 35 00.08 30
33 Inconel 700 250 HB 0.06 0.10 25 35 00.08 30
34 Stellite 21 350 HB 0.06 0.10 23 35 00.10 29
36 TiAl6V4 - 0.06 0.09 35 60 00.08 48
37 T40 - 0.06 0.09 28 40 00.08 34
38 45 HRc 0.06 0.09 50 90 00.08 70
38 50 HRc 0.06 0.09 40 70 00.08 55
38 55 HRc 0.06 0.09 30 60 00.08 45
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.06 0.09 40 60 00.08 50
White Cast Iron 41 G-X300CrMo15 55 HRc 0.06 0.09 30 50 00.08 40
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.06 0.11 200 400 00.09 300
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]
min max min max min maxMaterial Group Gr. N° VDI
GroupMaterial Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
346
DRILLING
W C M X
Shape ToleranceClearance Angle
80° m
l
Ø d7°
Fixing,Chipbreaker
s ± 0.13For l = 04/05/06, d ± 0.05 m ± 0.08For l = 08, d ± 0.08 m ± 0.13
s
M3001122
M3000953
M3001121
M3000954
0.80
0.80
0.80
1.20
Neutral
Neutral
Neutral
Neutral
2.38
3.97
3.18
4.76
4.00
6.00
5.00
8.00
WCMX 040208 NN LT 30
WCMX 06T308 NN LT 30
WCMX 050308 NN LT 30
WCMX 080412 NN LT 30
Insert Designation Catalog Nr.Directions rl
LT 30 Multi-MatTM General Usage – Standard
347
DRILLINGMachining Conditions
WCMX
WCMX 040208 NN – LT 30
min max min max Feed
1 125 HB 0.05 0.10 180 270 00.08 225
2 190 HB 0.05 0.10 180 230 00.08 205
3 250 HB 0.05 0.10 180 200 00.08 190
6 180 HB 0.05 0.10 120 230 00.08 175
4,6 230 HB 0.05 0.10 120 190 00.08 155
5,7 280 HB 0.05 0.10 100 170 00.07 135
8 350 HB 0.05 0.10 100 150 00.07 125
10 220 HB 0.07 0.10 70 170 00.09 120
10 280 HB 0.07 0.10 70 150 00.09 110
11 320 HB 0.07 0.09 60 130 00.08 95
11 350 HB 0.07 0.09 60 100 00.08 80
14 180 HB 0.05 0.10 170 230 00.07 200
14 240 HB 0.07 0.10 120 210 00.08 165
14 290 HB 0.07 0.09 70 120 00.08 95
14 310 HB 0.07 0.09 70 120 00.08 95
12 200 HB 0.07 0.09 100 150 00.08 125
13 42 HRc 0.05 0.08 60 100 00.07 80
15 150 HB 0.09 0.11 150 230 00.10 190
15 200 HB 0.09 0.11 150 210 00.10 180
16 250 HB 0.09 0.11 150 170 00.10 160
17,19 150 HB 0.09 0.11 120 200 00.10 160
17,19 200 HB 0.09 0.11 120 170 00.10 145
18,20 250 HB 0.09 0.11 120 150 00.10 135
31,32 Incoloy 800 240 HB 0.05 0.08 25 35 00.07 30
33 Inconel 700 250 HB 0.05 0.08 25 35 00.07 30
34 Stellite 21 350 HB 0.05 0.08 23 35 00.07 29
36 TiAl6V4 - 0.05 0.08 35 60 00.07 45
37 T40 - 0.05 0.08 28 40 00.07 34
38 45 HRc 0.05 0.08 50 90 00.07 70
38 50 HRc 0.05 0.08 40 70 00.07 55
38 55 HRc 0.05 0.08 30 60 00.07 45
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.05 0.08 40 60 00.07 50
White Cast Iron 41 G-X300CrMo15 55 HRc 0.05 0.08 30 50 00.07 40
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.05 0.10 200 400 00.08 300
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]
min max min max min maxMaterial Group Gr. N° VDI
GroupMaterial Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
348
DRILLING
348
Machining Conditions
WCMX 050308 NN – LT 30
min max min max Feed
1 125 HB 0.06 0.11 180 270 00.09 225
2 190 HB 0.06 0.11 180 230 00.09 205
3 250 HB 0.06 0.11 180 200 00.09 190
6 180 HB 0.06 0.11 120 230 00.09 175
4,6 230 HB 0.06 0.11 120 190 00.09 155
5,7 280 HB 0.06 0.11 100 170 00.08 135
8 350 HB 0.06 0.11 100 150 00.08 125
10 220 HB 0.09 0.11 70 170 00.10 120
10 280 HB 0.09 0.11 70 150 00.10 110
11 320 HB 0.09 0.10 60 130 00.09 95
11 350 HB 0.09 0.10 60 100 00.09 80
14 180 HB 0.06 0.11 170 230 00.08 200
14 240 HB 0.09 0.11 120 210 00.10 165
14 290 HB 0.09 0.10 70 120 00.09 95
14 310 HB 0.09 0.10 70 120 00.09 95
12 200 HB 0.09 0.10 100 150 00.09 125
13 42 HRc 0.06 0.09 60 100 00.08 80
15 150 HB 0.09 0.12 150 230 00.11 190
15 200 HB 0.09 0.12 150 210 00.11 180
16 250 HB 0.09 0.12 150 170 00.11 160
17,19 150 HB 0.09 0.12 120 200 00.11 160
17,19 200 HB 0.09 0.12 120 170 00.11 145
18,20 250 HB 0.09 0.12 120 150 00.11 135
31,32 Incoloy 800 240 HB 0.06 0.09 25 35 00.08 30
33 Inconel 700 250 HB 0.06 0.09 25 35 00.08 30
34 Stellite 21 350 HB 0.06 0.09 23 35 00.08 29
36 TiAl6V4 - 0.06 0.09 35 60 00.08 45
37 T40 - 0.06 0.09 28 40 00.08 34
38 45 HRc 0.06 0.09 50 90 00.08 70
38 50 HRc 0.06 0.09 40 70 00.08 55
38 55 HRc 0.06 0.09 30 60 00.08 45
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.06 0.09 40 60 00.08 50
White Cast Iron 41 G-X300CrMo15 55 HRc 0.06 0.09 30 50 00.08 40
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.06 0.11 200 400 00.09 300
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]
min max min max min maxMaterial Group Gr. N° VDI
GroupMaterial Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
349
DRILLINGMachining Conditions
WCMX 06T308 NN – LT 30
min max min max Feed
1 125 HB 0.06 0.12 180 270 00.09 225
2 190 HB 0.06 0.12 180 230 00.09 205
3 250 HB 0.06 0.12 180 200 00.09 190
6 180 HB 0.06 0.12 120 230 00.09 175
4,6 230 HB 0.06 0.12 120 190 00.09 155
5,7 280 HB 0.06 0.12 100 170 00.09 135
8 350 HB 0.06 0.12 100 150 00.09 125
10 220 HB 0.08 0.12 70 170 00.10 120
10 280 HB 0.08 0.12 70 150 00.10 110
11 320 HB 0.08 0.11 60 130 00.09 95
11 350 HB 0.08 0.11 60 100 00.09 80
14 180 HB 0.06 0.12 170 230 00.09 200
14 240 HB 0.08 0.12 120 210 00.10 165
14 290 HB 0.08 0.11 70 120 00.09 95
14 310 HB 0.08 0.11 70 120 00.09 95
12 200 HB 0.08 0.11 100 150 00.09 125
13 42 HRc 0.06 0.10 60 100 00.08 80
15 150 HB 0.09 0.13 150 230 00.11 190
15 200 HB 0.09 0.13 150 210 00.11 180
16 250 HB 0.09 0.13 150 170 00.11 160
17,19 150 HB 0.09 0.13 120 200 00.11 160
17,19 200 HB 0.09 0.13 120 170 00.11 145
18,20 250 HB 0.09 0.13 120 150 00.11 135
31,32 Incoloy 800 240 HB 0.06 0.10 25 35 00.08 30
33 Inconel 700 250 HB 0.06 0.10 25 35 00.08 30
34 Stellite 21 350 HB 0.06 0.10 23 35 00.08 29
36 TiAl6V4 - 0.06 0.10 35 60 00.08 45
37 T40 - 0.06 0.10 28 40 00.08 34
38 45 HRc 0.06 0.10 50 90 00.08 70
38 50 HRc 0.06 0.10 40 70 00.08 55
38 55 HRc 0.06 0.10 30 60 00.08 45
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.06 0.10 40 60 00.08 50
White Cast Iron 41 G-X300CrMo15 55 HRc 0.06 0.10 30 50 00.08 40
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.10 0.12 200 400 00.11 300
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]
min max min max min maxMaterial Group Gr. N° VDI
GroupMaterial Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
350
DRILLING
350
Machining Conditions
WCMX 080412 NN – LT 30
min max min max Feed
1 125 HB 0.06 0.16 180 270 00.11 225
2 190 HB 0.06 0.16 180 230 00.11 205
3 250 HB 0.06 0.16 180 200 00.11 190
6 180 HB 0.06 0.16 120 230 00.11 175
4,6 230 HB 0.06 0.16 120 190 00.11 155
5,7 280 HB 0.06 0.15 100 170 00.11 135
8 350 HB 0.06 0.15 100 150 00.11 125
10 220 HB 0.09 0.16 70 170 00.13 120
10 280 HB 0.09 0.16 70 150 00.13 110
11 320 HB 0.09 0.14 60 130 00.11 95
11 350 HB 0.09 0.14 60 100 00.11 80
14 180 HB 0.06 0.15 170 230 00.11 200
14 240 HB 0.09 0.15 120 210 00.12 165
14 290 HB 0.09 0.14 70 120 00.11 95
14 310 HB 0.09 0.14 70 120 00.11 95
12 200 HB 0.09 0.14 100 150 00.11 125
13 42 HRc 0.06 0.13 60 100 00.09 80
15 150 HB 0.10 0.18 150 230 00.14 190
15 200 HB 0.10 0.18 150 210 00.14 180
16 250 HB 0.10 0.18 150 170 00.14 160
17,19 150 HB 0.10 0.18 120 200 00.14 160
17,19 200 HB 0.10 0.18 120 170 00.14 145
18,20 250 HB 0.10 0.18 120 150 00.14 135
31,32 Incoloy 800 240 HB 0.06 0.13 25 35 00.09 30
33 Inconel 700 250 HB 0.06 0.13 25 35 00.09 30
34 Stellite 21 350 HB 0.06 0.13 23 35 00.09 29
36 TiAl6V4 - 0.06 0.13 35 60 00.09 45
37 T40 - 0.06 0.13 28 40 00.09 34
38 45 HRc 0.06 0.13 50 90 00.09 70
38 50 HRc 0.06 0.13 40 70 00.09 55
38 55 HRc 0.06 0.13 30 60 00.09 45
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.06 0.13 40 60 00.09 50
White Cast Iron 41 G-X300CrMo15 55 HRc 0.06 0.13 30 50 00.09 40
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.10 0.16 200 400 00.13 300
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N° VDIGroup
Material Exemples Hardness
D.O.C [mm] Feed [mm/rev] Amax[mm2]
Vc [m/min]
min max min max min maxMaterial Group Gr. N° VDI
GroupMaterial Exemples Hardness
Feed [mm/rev] Vc [m/min] Suggested Starting Parameters
min max min max Feed Vc
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
351
THREAD MILLING
THREAD MILLING
THREADMILLING
352
THREAD MILLING
TMC03012L5 0.35 ISO TH400001M1.6x0.35 0.35 39 5.1 3 1.20 3
TMC06015L6 0.4 ISO TH400019M2.0x0.4 0.40 39 6.1 3 1.54 3
TMC06019L7 0.45 ISO TH400016M2.5x0.45 0.45 39 7.6 4 1.96 3
TMC06024L9 0. 5 ISO TH400013M3.0x0.5 0.50 51 9.3 4 2.40 3
TMC06031L12 0.7 ISO TH400004M4.0x0.7 0.70 51 12.4 6 3.15 3
TMC06040L15 0.8 ISO TH400010M5.0x0.8 0.80 57 15.6 6 4.00 3
TMC06047L19 1.0 ISO TH400007M6.0x1.0 1.00 57 19.0 6 4.75 3
TMC06059L24 1.25 ISO TH400022M8.0x1.25 1.25 57 24.3 6 5.95 3
TMC08079L31 1.5 ISO TH400025M10x1.5 1.50 63 31.0 8 7.90 3
Thread Size Pitchmm Catalog Nr.L L1 D1 D2 N° of
FlutesDesignation
ISO METRIC Internal Miniature Tools
Thread Length - Up to 3D D = Nominal Thread Size
60°
1/8P
1/4PUNNUT
UNSCREW
ISO 965-1:1999-11DIN 13: 2005-08
L1L
D2 D1
TH4000520-80UNF- 80 39 3.9 3 1.18 3TMC03011L3 80UN
TH4000401-72UNF- 72 39 5.8 3 1.44 3TMC03014L5 72UN
TH4000343-56UNF2-56UNC 56 39 6.8 3 1.66 3TMC03016L6 56UN
TH400028-4-40UNC 40 51 8.1 6 2.12 3TMC06021L8 40UN
TH4000556-40UNF5-40UNC 40 51 9.8 6 2.46 3TMC06024L9 40UN
TH400031-6-32UNC 32 51 10.7 6 2.57 3TMC06025L10 32UN
TH40003710-32UNF8-32UNC 32 57 12.7 6 3.22 3TMC06032L12 32UN
TH4000431/4-28UNF- 28 57 19.3 6 5.20 3TMC06052L19 28 UN
TH4000495/16-24UNF- 24 63 24.2 8 6.65 3TMC08066L24 24 UN
Fine UNFCoarse UNC PitchTPI Catalog Nr.L L1 D1 D2 N° of
FlutesDesignation
UN Internal Miniature Tools
TH4000467/16-20UNF1/4-20UNC 20 19.4 6 4.85 3TMC06048L19 20UN 57
353
THREAD MILLING
min max
1 125 HB 80 130
2 190 HB 70 110
3 250 HB 60 100
6 180 HB 70 110
4,6 230 HB 70 110
5,7 280 HB 60 100
8 350 HB 50 80
10 220 HB 70 110
10 280 HB 60 100
11 320 HB 50 80
11 350 HB 50 70
14 180 HB 70 110
14 240 HB 60 90
14 290 HB 60 80
14 310 HB 60 80
12 200 HB 70 90
13 42 HRc 60 80
15 150 HB 60 110
15 200 HB 70 110
16 250 HB 60 90
17,19 150 HB 60 110
17,19 200 HB 60 90
18,20 250 HB 60 90
31,32 Incoloy 800 240 HB 40 60
33 Inconel 700 250 HB 30 50
34 Stellite 21 350 HB 20 40
36 TiAl6V4 - 40 70
37 T40 - 25 50
38 45 HRc 30 50
38 50 HRc 25 50
38 55 HRc 25 40
Chilled Cast Iron 40 Ni-Hard 2 400 HB 25 40
White Cast Iron 41 G-X300CrMo15 55 HRc 25 40
NF Al (>8%Si) 12 25 AlSi12 130 HB 80 300
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3X40CrMoV5,
H13, M42, D3, S6-5-2, 12Ni19
4304, 316,
X5CrNi18-9
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
X100CrMo13, 440C,
G-X260NiCr4211
GGG40, GGG70, 50005
9
10
7 GG20, GG40, EN-GJL-250,
No30B
8
Material Group Gr. N° VDIGroup
Material Exemples Hardness
Vc [m/min]
min max
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Feed (mm/tooth) per cutting dia
1.5-3.0 3.0-5.0 5.0-7.0 7.0-9.0 9.0-11
354
SOLID END MILL
355
SOLID END MILL
SOLID ENDMILLSSOLID CARBIDEEND MILLS LT 4000
SOLIDENDMILL
356
SOLID END MILL
2 fl
30°
L2
L1
D2 D1
L2
L1
D2 D1
Designation D1 Catalog Nr.L2D2 L1
E90 Z2 D01.0(03) L03.0(038) LT 4000 1.0 3 38 3.0 M5003520
E90 Z2 D01.5(03) L05.0(038) LT 4000 1.5 3 38 5.0 M5003537
E90 Z2 D02.0(03) L06.0(038) LT 4000 2.0 3 38 6.0 M5003538
E90 Z2 D02.5(03) L07.0(038) LT 4000 2.5 3 38 7.0 M5003539
E90 Z2 D03.0(03) L09.0(038) LT 4000 3.0 3 38 9.0 M5003540
E90 Z2 D04.0(04) L14.0(050) LT 4000 4.0 4 50 14.0 M5003541
E90 Z2 D05.0(05) L16.0(050) LT 4000 5.0 5 50 16.0 M5003542
E90 Z2 D06.0(06) L20.0(063) LT 4000 6.0 6 63 20.0 M5003543
E90 Z2 D08.0(08) L20.0(063) LT 4000 8.0 8 63 20.0 M5003544
E90 Z2 D10.0(10) L22.0(072) LT 4000 10.0 10 72 22.0 M5003545
E90 Z2 D12.0(12) L26.0(075) LT 4000 12.0 12 75 26.0 M5003546
90° 2 Flutes
357
SOLID END MILLMachining Conditions
1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.010 0.012 0.017 0.024 0.030 150 200
2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.010 0.012 0.017 0.024 0.030 140 190
3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.010 0.012 0.017 0.024 0.030 120 160
6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.010 0.011 0.016 0.025 0.030 120 180
4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.010 0.011 0.016 0.025 0.030 90 130
5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.007 0.009 0.014 0.020 0.024 80 120
8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.007 0.009 0.014 0.020 0.024 60 90
10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.010 0.015 0.021 0.026 70 130
10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.010 0.015 0.021 0.026 65 110
11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.007 0.008 0.011 0.016 0.020 60 90
11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.007 0.008 0.011 0.016 0.020 50 80
14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.007 0.008 0.012 0.017 0.022 80 120
14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.007 0.008 0.012 0.017 0.022 70 115
14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.006 0.006 0.009 0.013 0.017 60 100
14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.006 0.006 0.009 0.013 0.017 60 90
12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.006 0.006 0.009 0.013 0.017 50 90
13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.006 0.006 0.009 0.013 0.017 30 55
15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.014 0.020 0.029 0.036 140 200
15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.014 0.020 0.029 0.036 150 190
16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.014 0.020 0.029 0.036 120 160
17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.010 0.012 0.017 0.025 0.031 130 180
17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.010 0.012 0.017 0.025 0.031 110 150
18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.010 0.012 0.017 0.025 0.031 90 130
31,32 Incoloy 800 240 HB 1.5xØ 0.3xØ 1.0xØ 0.006 0.007 0.010 0.014 0.018 30 50
33 Inconel 700 250 HB 1.5xØ 0.3xØ 1.0xØ 0.006 0.007 0.010 0.014 0.018 25 45
34 Stellite 21 350 HB 1.5xØ 0.3xØ 1.0xØ 0.006 0.007 0.010 0.014 0.018 20 50
36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.006 0.007 0.010 0.015 0.018 30 60
37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.006 0.007 0.010 0.015 0.018 40 70
38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.004 0.005 0.007 0.011 0.013 40 60
38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.004 0.005 0.007 0.011 0.013 35 55
38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.003 0.004 0.005 0.008 0.010 30 50
Chilled Cast Iron 40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.003 0.004 0.005 0.008 0.010 35 55
White Cast Iron 41 G-X300CrMo15 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.003 0.004 0.005 0.008 0.010 30 50
NF Al (>8%Si) 12 25 AlSi12 130 HB 1.5xØ 0.5xØ 0.1xØ 0.011 0.013 0.018 0.027 0.033 160 250
2
X2CrNiN23-4, S31500
3
6 410, X6Cr17, 17-4 PH, 430
4304, 316, X5CrNi18-
9
X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
11
GGG40, GGG70, 50005
9
7 GG20, GG40, EN-GJL-250,
No30B
10
8
X100CrMo13, 440C,
G-X260NiCr42
E90° Z2 Ø 1 - 5 – LT 4000
Material Group Gr. N° VDIGroup
Material Examples Hardness
profiling slotting fz[mm/tooth] Vc [m/min]
ap ae ap Ø 1.0 Ø 2.0 Ø3.0 Ø4.0 Ø5.0 min max
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
358
SOLID END MILL Machining Conditions
1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 150 200
2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 140 190
3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 120 160
6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 120 180
4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 90 130
5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 80 120
8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 60 90
10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 70 130
10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 65 110
11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 60 90
11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 50 80
14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 80 120
14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 70 115
14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 100
14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 90
12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 50 90
13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 30 55
15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 140 200
15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 150 190
16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 120 160
17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 130 180
17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 110 150
18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 90 130
31,32 Incoloy 800 240 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 30 50
33 Inconel 700 250 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 25 45
34 Stellite 21 350 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 20 50
36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 30 60
37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 40 70
38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 40 60
38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 35 55
38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50
Chilled Cast Iron 40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 35 55
White Cast Iron 41 G-X300CrMo15 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50
NF Al (>8%Si) 12 25 AlSi12 130 HB 1.5xØ 0.5xØ 0.1xØ 0.042 0.058 0.069 0.081 160 250
2
X2CrNiN23-4, S31500
3
6 410, X6Cr17, 17-4 PH, 430
4304, 316, X5CrNi18-
9
X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
11
GGG40, GGG70, 50005
9
7 GG20, GG40, EN-GJL-250,
No30B
10
8
X100CrMo13, 440C,
G-X260NiCr42
E90° Z2 Ø 6, 8, 10, 12 – LT 4000
Material Group Gr. N° VDIGroup
Material Examples Hardness profiling slotting fz[mm/tooth] Vc [m/min]
ap ae ap Ø 6.0 Ø 8.0 Ø10.0 Ø12.0 min max
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
359
SOLID END MILL
3 fl
40°
L2
L1
D2 D1
Designation D1 Catalog Nr.L2D2 L1
E90 Z3 D03.0(06) L08.0(050) LT 4000 3.0 6 50 8.0 M5003548
E90 Z3 D04.0(06) L11.0(050) LT 4000 4.0 6 50 11.0 M5003549
E90 Z3 D05.0(06) L13.0(050) LT 4000 5.0 6 50 13.0 M5003550
E90 Z3 D06.0(06) L16.0(050) LT 4000 6.0 6 50 16.0 M5003551
E90 Z3 D08.0(08) L20.0(060) LT 4000 8.0 8 60 20.0 M5003552
E90 Z3 D10.0(10) L25.0(072) LT 4000 10.0 10 72 25.0 M5003553
E90 Z3 D12.0(12) L30.0(075) LT 4000 12.0 12 75 30.0 M5003554
90° 3 Flutes
v
Machining Conditions
360
SOLID END MILL
1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.018 0.027 0.033 150 200
2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.018 0.027 0.033 140 190
3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.018 0.027 0.033 120 160
6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 120 180
4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 90 130
5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.015 0.021 0.026 80 120
8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.015 0.021 0.026 60 90
10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.015 0.021 0.026 70 130
10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.015 0.021 0.026 65 110
11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.011 0.016 0.020 60 90
11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.011 0.016 0.020 50 80
14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.017 0.022 80 120
14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.017 0.022 70 115
14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 60 100
14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 60 90
12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.016 50 90
13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.016 30 55
15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 140 200
15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 150 190
16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 120 160
17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 130 180
17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 110 150
18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 90 130
31,32 Incoloy 800 240 HB 1.5xØ 0.3xØ 1.0xØ 0.010 0.014 0.018 30 50
33 Inconel 700 250 HB 1.5xØ 0.3xØ 1.0xØ 0.010 0.014 0.018 25 45
34 Stellite 21 350 HB 1.5xØ 0.2xØ 1.0xØ 0.010 0.014 0.018 20 50
36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.007 0.011 0.013 30 60
37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.007 0.011 0.013 40 70
38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.006 0.009 0.012 40 60
38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.006 0.009 0.012 35 55
38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.006 0.008 0.010 30 50
Chilled Cast Iron 40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.006 0.008 0.010 35 55
White Cast Iron 41 G-X300CrMo15 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.006 0.008 0.010 30 50
NF Al (>8%Si) 12 25 AlSi12 130 HB 1.5xØ 0.5 x Ø 1.0 x Ø 0.018 0.027 0.033 160 250
X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
2
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
4304, 316,
X5CrNi18-9
8
X100CrMo13, 440C,
G-X260NiCr42 11
9
10
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
E90° Z3 Ø 3 - 5 – LT 4000
Material Group Gr. N° VDIGroup
Material Examples Hardness
profiling slotting fz[mm/tooth] Vc [m/min]
ap ae ap Ø 3.0 Ø 4.0 Ø5.0 min max
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Machining Conditions
361
SOLID END MILL
1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.042 0.058 0.069 0.081 150 200
2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.042 0.058 0.069 0.081 140 190
3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.042 0.058 0.069 0.081 120 160
6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.054 0.065 0.076 120 180
4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.054 0.065 0.076 90 130
5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.034 0.046 0.055 0.065 80 120
8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.034 0.046 0.055 0.065 60 90
10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 70 130
10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 65 110
11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 60 90
11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 50 80
14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 80 120
14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 70 115
14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 100
14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 90
12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.028 0.033 0.039 50 90
13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.020 0.028 0.033 0.039 30 55
15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 140 200
15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 150 190
16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 120 160
17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 130 180
17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 110 150
18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 90 130
31,32 Incoloy 800 240 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 30 50
33 Inconel 700 250 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 25 45
34 Stellite 21 350 HB 1.5xØ 0.2xØ 1.0xØ 0.023 0.031 0.037 0.044 20 50
36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.017 0.023 0.028 0.032 30 60
37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.017 0.023 0.028 0.032 40 70
38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.015 0.020 0.024 0.028 40 60
38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.015 0.020 0.024 0.028 35 55
38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50
Chilled Cast Iron 40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 35 55
White Cast Iron 41 G-X300CrMo15 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50
NF Al (>8%Si) 12 25 AlSi12 130 HB 1.5xØ 0.5 x Ø 1.0 x Ø 0.042 0.058 0.069 0.081 160 250
8
X100CrMo13, 440C,
G-X260NiCr42 11
9
10
GGG40, GGG70, 50005
7 GG20, GG40, EN-GJL-250,
No30B
5X2CrNiN23-4,
S31500
6 410, X6Cr17, 17-4 PH, 430
4304, 316,
X5CrNi18-9
3X40CrMoV5,
H13, M42, D3, S6-5-2, 12Ni19
2
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
E90° Z3 Ø 6, 8, 10, 12 – LT 4000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Ex mples Hardness
profiling slotting fz[mm/tooth] Vc [m/min]
ap ae ap Ø 6.0 Ø 8.0 Ø10.0 Ø12.0 min max
Machining Conditions
362
SOLID END MILL
L2
L1
D2 D1
L2
L1
D2 D138°- 41°
4 fl
unequal
variable
Designation D1 Catalog Nr.L2D2 L1
90° 4 Flutes
E90 Z4 D03.0(06) L08.0(050) LT 4000 3.0 6 50 8.0 M5003572
E90 Z4 D04.0(06) L11.0(050) LT 4000 4.0 6 50 11.0 M5003573
E90 Z4 D05.0(06) L13.0(050) LT 4000 5.0 6 50 13.0 M5003574
E90 Z4 D06.0(06) L16.0(050) LT 4000 6.0 6 50 16.0 M5003575
E90 Z4 D08.0(08) L20.0(060) LT 4000 8.0 8 60 20.0 M5003576
E90 Z4 D10.0(10) L22.0(072) LT 4000 10.0 10 72 22.0 M5003577
E90 Z4 D12.0(12) L26.0(075) LT 4000 12.0 12 75 26.0 M5003578
E90 Z4 D16.0(16) L38.0(100) LT 4000 16.0 16 100 38.0 M5003579
E90 Z4 D01.0(04) L04.0(050) LT 4000 1.0 4 50 4.0 M5003555
E90 Z4 D01.5(04) L05.0(050) LT 4000 1.5 4 50 5.0 M5003569
E90 Z4 D01.0(04) L05.0(050) LT 4000 1.5 4 50 5.0 M5003569
E90 Z4 D01.5(04) L07.5(050) LT 4000 1.5 4 50 7.5 M5003556
E90 Z4 D02.5(04) L12.5(050) LT 4000 2.5 4 50 12 .5 M5003558
E90 Z4 D02.0(04) L08.0(050) LT 4000 2.0 4 50 8.0 M5003557
E90 Z4 D02.0(04) L06.0(050) LT 4000 2.0 4 50 6.0 M5003570
E90 Z4 D02.5(04) L08.0(050) LT 4000 2.5 4 50 8.0 M5003571
363
SOLID END MILL
1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.024 0.030 150 200
2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.024 0.030 140 190
3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.024 0.030 120 160
6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.016 0.025 0.030 120 180
4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.016 0.025 0.030 90 130
5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.014 0.020 0.024 80 120
8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.014 0.020 0.024 60 90
10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.015 0.021 0.026 70 130
10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.015 0.021 0.026 65 110
11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.011 0.016 0.020 60 90
11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.011 0.016 0.020 50 80
14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.017 0.022 80 120
14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.017 0.022 70 115
14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 60 100
14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 60 90
12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 50 90
13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 30 55
15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 140 200
15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 150 190
16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 120 160
17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 130 180
17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 110 150
18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 90 130
31,32 Incoloy 800 240 HB 1.5xØ 0.3xØ 1.0xØ 0.010 0.014 0.018 30 50
33 Inconel 700 250 HB 1.5xØ 0.3xØ 1.0xØ 0.010 0.014 0.018 25 45
34 Stellite 21 350 HB 1.5xØ 0.3xØ 1.0xØ 0.010 0.014 0.018 20 50
36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.010 0.015 0.018 30 60
37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.010 0.015 0.018 40 70
38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.007 0.011 0.013 40 60
38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.007 0.011 0.013 35 55
38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.005 0.008 0.010 30 50
Chilled Cast Iron 40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.005 0.008 0.010 35 55
White Cast Iron 41 G-X300CrMo15 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.005 0.008 0.010 30 50
NF Al (>8%Si) 12 25 AlSi12 130 HB 1.5xØ 0.5xØ 1.0xØ 0.018 0.027 0.033 160 250
X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
3
6 410, X6Cr17, 17-4 PH, 430
4304, 316,
X5CrNi18-9
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
11
GGG40, GGG70, 50005
9
7 GG20, GG40, EN-GJL-250,
No30B
10
8
X100CrMo13, 440C,
G-X260NiCr42
E90° Z4 Ø 3 - 5 – LT 4000
Material Group Gr. N° VDIGroup
Material Examples Hardness
profiling slotting fz[mm/tooth] Vc [m/min]
ap ae ap Ø 3.0 Ø 4.0 Ø5.0 min max
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Machining Conditions
364
SOLID END MILL
1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 150 200
2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 140 190
3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 120 160
6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 120 180
4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 90 130
5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 80 120
8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 60 90
10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 70 130
10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 65 110
11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 60 90
11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 50 80
14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 80 120
14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 70 115
14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 100
14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 90
12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 50 90
13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 30 55
15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 140 200
15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 150 190
16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 120 160
17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 130 180
17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 110 150
18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 90 130
31,32 Incoloy 800 240 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 30 50
33 Inconel 700 250 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 25 45
34 Stellite 21 350 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 20 50
36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 30 60
37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 40 70
38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 40 60
38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 35 55
38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50
Chilled Cast Iron 40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 35 55
White Cast Iron 41 G-X300CrMo15 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50
NF Al (>8%Si) 12 25 AlSi12 130 HB 1.5xØ 0.5xØ 1.0xØ 0.042 0.058 0.069 0.081 160 250
X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
3
6 410, X6Cr17, 17-4 PH, 430
4304, 316,
X5CrNi18-9
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
11
GGG40, GGG70, 50005
9
7 GG20, GG40, EN-GJL-250,
No30B
10
8
X100CrMo13, 440C,
G-X260NiCr42
E90° Z4 Ø 6, 8, 10, 12 – LT 4000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Machining Conditions
Material Group Gr. N° VDIGroup
Material Ex mples Hardness
profiling slotting fz[mm/tooth] Vc [m/min]
ap ae ap Ø 6.0 Ø 8.0 Ø10.0 Ø12.0 min max
365
SOLID END MILL
unequal
L2
L1
D2 D1
R38°- 41°
4 fl
variable
90° 4 Flutes with RadiusProduct Designation D1 D2 L1 L2 R Catalog Nr.
E90 Z4 D03.0(06) L08.0(050)R0.5 LT 4000 3.0 6 50 8.0 0.5 M5003614
E90 Z4 D04.0(06) L11.0(050)R0.5 LT 4000 4.0 6 50 11.0 0.5 M5003615
E90 Z4 D05.0(06) L13.0(050)R0.5 LT 4000 5.0 6 50 13.0 0.5 M5003616
E90 Z4 D06.0(06) L16.0(050)R0.5 LT 4000 6.0 6 50 16.0 0.5 M5003617
E90 Z4 D08.0(08) L20.0(060)R0.5 LT 4000 8.0 8 60 20.0 0.5 M5003618
E90 Z4 D10.0(10) L22.0(072)R0.5 LT 4000 10.0 10 72 22.0 0.5 M5003619
E90 Z4 D12.0(12) L26.0(075)R0.5 LT 4000 12.0 12 75 26.0 0.5 M5003620
E90 Z4 D03.0(06) L08.0(050)R1.0 LT 4000 3.0 6 50 08.0 1.0 M5003623
E90 Z4 D04.0(06) L11.0(050)R1.0 LT 4000 4.0 6 50 11.0 1.0 M5003624
E90 Z4 D05.0(06) L13.0(050)R1.0 LT 4000 5.0 6 50 13.0 1.0 M5003625
E90 Z4 D06.0(06) L16.0(050)R1.0 LT 4000 6.0 6 50 16.0 1.0 M5003626
E90 Z4 D08.0(08) L20.0(060)R1.0 LT 4000 8.0 8 60 20.0 1.0 M5003627
E90 Z4 D10.0(10) L22.0(072)R1.0 LT 4000 10.0 10 72 22.0 1.0 M5003628
E90 Z4 D12.0(12) L26.0(075)R1.0 LT 4000 12.0 12 75 26.0 1.0 M5003629
E90 Z4 D06.0(06) L16.0(050)R2.0 LT 4000 6.0 6 50 16.0 2.0 M5003632
E90 Z4 D08.0(08) L20.0(060)R2.0 LT 4000 8.0 8 60 20.0 2.0 M5003633
E90 Z4 D10.0(10) L22.0(072)R2.0 LT 4000 10.0 10 72 22.0 2.0 M5003634
E90 Z4 D12.0(12) L26.0(075)R2.0 LT 4000 12.0 12 75 26.0 2.0 M5003635
Product Designation D1 D2 L1 L2 R Catalog Nr.
E90 Z4 D08.0(08) L32.0(090)R0.5 LT 4000 8.0 8 90 32.0 0.5 M5003638
E90 Z4 D10.0(10) L40.0(100)R0.5 LT 4000 10.0 10 100 40.0 0.5 M5003639
E90 Z4 D12.0(12) L48.0(110)R0.5 LT 4000 12.0 12 110 48.0 0.5 M5003640
90° 4 Flutes with Radius, Long
366
SOLID END MILL Machining Conditions
1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.024 0.030 150 200
2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.024 0.030 140 190
3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.024 0.030 120 160
6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.016 0.025 0.030 120 180
4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.016 0.025 0.030 90 130
5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.014 0.020 0.024 80 120
8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.014 0.020 0.024 60 90
10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.015 0.021 0.026 70 130
10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.015 0.021 0.026 65 110
11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.011 0.016 0.020 60 90
11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.011 0.016 0.020 50 80
14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.017 0.022 80 120
14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.017 0.022 70 115
14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 60 100
14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 60 90
12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 50 90
13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 30 55
15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 140 200
15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 150 190
16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 120 160
17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 130 180
17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 110 150
18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 90 130
31,32 Incoloy 800 240 HB 1.5xØ 0.3xØ 1.0xØ 0.010 0.014 0.018 30 50
33 Inconel 700 250 HB 1.5xØ 0.3xØ 1.0xØ 0.010 0.014 0.018 25 45
34 Stellite 21 350 HB 1.5xØ 0.3xØ 1.0xØ 0.010 0.014 0.018 20 50
36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.010 0.015 0.018 30 60
37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.010 0.015 0.018 40 70
38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.007 0.011 0.013 40 60
38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.007 0.011 0.013 35 55
38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.005 0.008 0.010 30 50
40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.005 0.008 0.010 35 55
41 G-X300CrMo15 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.005 0.008 0.010 30 50
12 25 AlSi12 130 HB 1.5xØ 0.5xØ 1.0xØ 0.018 0.027 0.033 160 250
11
GGG40, GGG70, 50005
9
7 GG20, GG40, EN-GJL-250,
No30B
10
8
X100CrMo13, 440C,
G-X260NiCr42
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
6 410, X6Cr17, 17-4 PH, 430
4304, 316,
X5CrNi18-9
2
X2CrNiN23-4, S31500
3X40CrMoV5,
H13, M42, D3, S6-5-2, 12Ni19
5
E90° Z4 with Radius 0.5, Ø 3 - 5 – LT 4000
Material Group Gr. N° VDIGroup
Material Examples Hardness
profiling slotting fz[mm/tooth] Vc [m/min]
ap ae ap Ø 3.0 Ø 4.0 Ø5.0 min max
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
367
SOLID END MILLMachining Conditions
1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 150 200
2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 140 190
3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 120 160
6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 120 180
4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 90 130
5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 80 120
8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 60 90
10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 70 130
10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 65 110
11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 60 90
11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 50 80
14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 80 120
14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 70 115
14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 100
14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 90
12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 50 90
13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 30 55
15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 140 200
15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 150 190
16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 120 160
17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 130 180
17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 110 150
18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 90 130
31,32 Incoloy 800 240 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 30 50
33 Inconel 700 250 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 25 45
34 Stellite 21 350 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 20 50
36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 30 60
37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 40 70
38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 40 60
38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 35 55
38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50
40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 35 55
41 G-X300CrMo15 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50
12 25 AlSi12 130 HB 1.5xØ 0.5xØ 1.0xØ 0.042 0.058 0.069 0.081 160 250
11
GGG40, GGG70, 50005
9
7 GG20, GG40, EN-GJL-250,
No30B
10
8
X100CrMo13, 440C,
G-X260NiCr42
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
6 410, X6Cr17, 17-4 PH, 430
4304, 316,
X5CrNi18-9
2
X2CrNiN23-4, S31500
3X40CrMoV5,
H13, M42, D3, S6-5-2, 12Ni19
5
E90° Z4 with Radius 0.5, Ø 6, 8, 10, 12 – LT 4000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Ex mples Hardness
profiling slotting fz[mm/tooth] Vc [m/min]
ap ae ap Ø 6.0 Ø 8.0 Ø10.0 Ø12.0 min max
368
SOLID END MILL Machining Conditions
1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.024 0.030 150 200
2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.024 0.030 140 190
3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.024 0.030 120 160
6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.016 0.025 0.030 120 180
4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.016 0.025 0.030 90 130
5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.014 0.020 0.024 80 120
8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.014 0.020 0.024 60 90
10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.015 0.021 0.026 70 130
10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.015 0.021 0.026 65 110
11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.011 0.016 0.020 60 90
11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.011 0.016 0.020 50 80
14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.017 0.022 80 120
14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.017 0.022 70 115
14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 60 100
14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 60 90
12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 50 90
13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 30 55
15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 140 200
15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 150 190
16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 120 160
17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 130 180
17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 110 150
18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 90 130
31,32 Incoloy 800 240 HB 1.5xØ 0.3xØ 1.0xØ 0.010 0.014 0.018 30 50
33 Inconel 700 250 HB 1.5xØ 0.3xØ 1.0xØ 0.010 0.014 0.018 25 45
34 Stellite 21 350 HB 1.5xØ 0.3xØ 1.0xØ 0.010 0.014 0.018 20 50
36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.010 0.015 0.018 30 60
37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.010 0.015 0.018 40 70
38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.007 0.011 0.013 40 60
38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.007 0.011 0.013 35 55
38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.005 0.008 0.010 30 50
40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.005 0.008 0.010 35 55
41 G-X300CrMo15 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.005 0.008 0.010 30 50
12 25 AlSi12 130 HB 1.5xØ 0.5xØ 1.0xØ 0.018 0.027 0.033 160 250
2
X2CrNiN23-4, S31500
3X40CrMoV5,
H13, M42, D3, S6-5-2, 12Ni19
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
6 410, X6Cr17, 17-4 PH, 430
4304, 316,
X5CrNi18-9
11
GGG40, GGG70, 50005
9
7 GG20, GG40, EN-GJL-250,
No30B
10
8
X100CrMo13, 440C,
G-X260NiCr42
E90° Z4 with Radius 1.0, Ø 3 - 5 – LT 4000
Material Group Gr. N° VDIGroup
Material Examples Hardness
profiling slotting fz[mm/tooth] Vc [m/min]
ap ae ap Ø 3.0 Ø 4.0 Ø5.0 min max
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
369
SOLID END MILLMachining Conditions
1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 150 200
2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 140 190
3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 120 160
6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 120 180
4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 90 130
5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 80 120
8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 60 90
10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 70 130
10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 65 110
11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 60 90
11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 50 80
14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 80 120
14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 70 115
14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 100
14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 90
12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 50 90
13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 30 55
15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 140 200
15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 150 190
16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 120 160
17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 130 180
17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 110 150
18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 90 130
31,32 Incoloy 800 240 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 30 50
33 Inconel 700 250 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 25 45
34 Stellite 21 350 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 20 50
36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 30 60
37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 40 70
38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 40 60
38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 35 55
38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50
40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 35 55
41 G-X300CrMo15 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50
12 25 AlSi12 130 HB 1.5xØ 0.5xØ 1.0xØ 0.042 0.058 0.069 0.081 160 250
2
X2CrNiN23-4, S31500
3X40CrMoV5,
H13, M42, D3, S6-5-2, 12Ni19
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
6 410, X6Cr17, 17-4 PH, 430
4304, 316,
X5CrNi18-9
11
GGG40, GGG70, 50005
9
7 GG20, GG40, EN-GJL-250,
No30B
10
8
X100CrMo13, 440C,
G-X260NiCr42
E90° Z4 with Radius 1.0, Ø 6, 8, 10, 12 – LT 4000
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Material Group Gr. N° VDIGroup
Material Ex mples Hardness
profiling slotting fz[mm/tooth] Vc [m/min]
ap ae ap Ø 6.0 Ø 8.0 Ø10.0 Ø12.0 min max
370
SOLID END MILL Machining Conditions
1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 150 200
2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 140 190
3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 120 160
6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 120 180
4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 90 130
5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 80 120
8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 60 90
10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 70 130
10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 65 110
11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 60 90
11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 50 80
14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 80 120
14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 70 115
14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 100
14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 90
12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 50 90
13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 30 55
15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 140 200
15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 150 190
16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 120 160
17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 130 180
17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 110 150
18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 90 130
31,32 Incoloy 800 240 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 30 50
33 Inconel 700 250 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 25 45
34 Stellite 21 350 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 20 50
36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 30 60
37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 40 70
38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 40 60
38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 35 55
38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50
40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 35 55
41 G-X300CrMo15 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50
12 25 AlSi12 130 HB 1.5xØ 0.5xØ 1.0xØ 0.042 0.058 0.069 0.081 160 250
2
X2CrNiN23-4, S31500
3X40CrMoV5,
H13, M42, D3, S6-5-2, 12Ni19
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
6 410, X6Cr17, 17-4 PH, 430
4304, 316,
X5CrNi18-9
11
GGG40, GGG70, 50005
9
7 GG20, GG40, EN-GJL-250,
No30B
10
8
X100CrMo13, 440C,
G-X260NiCr42
E90° Z4 with Radius 2.0, Ø 6, 8, 10, 12 – LT 4000
Material Group Gr. N° VDIGroup
Material Examples Hardness profiling slotting fz[mm/tooth] Vc [m/min]
ap ae ap Ø 6.0 Ø 8.0 Ø10.0 Ø12.0 min max
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
371
SOLID END MILLMachining Conditions
1 125 HB 3.0xØ 0.25xØ 1.0xØ 0.050 0.059 0.070 150 200
2 190 HB 3.0xØ 0.25xØ 1.0xØ 0.050 0.059 0.070 140 190
3 250 HB 3.0xØ 0.25xØ 1.0xØ 0.050 0.059 0.070 120 160
6 180 HB 3.0xØ 0.25xØ 1.0xØ 0.044 0.053 0.062 120 180
4,6 230 HB 3.0xØ 0.25xØ 1.0xØ 0.044 0.053 0.062 90 130
5,7 280 HB 3.0xØ 0.25xØ 0.7xØ 0.035 0.042 0.049 80 120
8 350 HB 3.0xØ 0.25xØ 0.7xØ 0.035 0.042 0.049 60 90
10 220 HB 3.0xØ 0.25xØ 0.7xØ 0.035 0.042 0.049 70 130
10 280 HB 3.0xØ 0.25xØ 0.7xØ 0.035 0.042 0.049 65 110
11 320 HB 3.0xØ 0.25xØ 0.5xØ 0.025 0.030 0.035 60 90
11 350 HB 3.0xØ 0.25xØ 0.5xØ 0.025 0.030 0.035 50 80
14 180 HB 3.0xØ 0.25xØ 1.0xØ 0.032 0.039 0.045 80 120
14 240 HB 3.0xØ 0.25xØ 1.0xØ 0.032 0.039 0.045 70 115
14 290 HB 3.0xØ 0.25xØ 1.0xØ 0.025 0.030 0.035 60 100
14 310 HB 3.0xØ 0.25xØ 1.0xØ 0.025 0.030 0.035 60 90
12 200 HB 3.0xØ 0.25xØ 1.0xØ 0.024 0.029 0.033 50 90
13 42 HRc 3.0xØ 0.25xØ 1.0xØ 0.024 0.029 0.033 30 55
15 150 HB 3.0xØ 0.25xØ 1.0xØ 0.047 0.056 0.066 140 200
15 200 HB 3.0xØ 0.25xØ 1.0xØ 0.047 0.056 0.066 150 190
16 250 HB 3.0xØ 0.25xØ 1.0xØ 0.047 0.056 0.066 120 160
17,19 150 HB 3.0xØ 0.25xØ 1.0xØ 0.045 0.053 0.063 130 180
17,19 200 HB 3.0xØ 0.25xØ 1.0xØ 0.045 0.053 0.063 110 150
18,20 250 HB 3.0xØ 0.25xØ 1.0xØ 0.045 0.053 0.063 90 130
31,32 Incoloy 800 240 HB 3.0xØ 0.10xØ 1.0xØ 0.020 0.024 0.028 30 50
33 Inconel 700 250 HB 3.0xØ 0.10xØ 1.0xØ 0.020 0.024 0.028 25 45
34 Stellite 21 350 HB 3.0xØ 0.10xØ 1.0xØ 0.020 0.024 0.028 20 50
36 TiAl6V4 - 3.0xØ 0.25xØ 1.0xØ 0.020 0.024 0.028 30 60
37 T40 - 3.0xØ 0.25xØ 1.0xØ 0.020 0.024 0.028 40 70
38 45 HRc 3.0xØ 0.10xØ 0.1xØ 0.017 0.021 0.024 40 60
38 50 HRc 3.0xØ 0.10xØ 0.1xØ 0.017 0.021 0.024 35 55
38 55 HRc 3.0xØ 0.10xØ 0.1xØ 0.015 0.018 0.021 30 50
40 Ni-Hard 2 400 HB 3.0xØ 0.10xØ 0.1xØ 0.015 0.018 0.021 35 55
41 G-X300CrMo15 55 HRc 3.0xØ 0.10xØ 0.1xØ 0.015 0.018 0.021 30 50
12 25 AlSi12 130 HB 3.0xØ 0.25xØ 1.0xØ 0.050 0.059 0.070 160 250
X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
4304, 316,
X5CrNi18-9
10
8
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
7 GG20, GG40, EN-GJL-250,
No30B
E90° Z4 with Radius 0.5 Long, Ø 8, 10, 12 – LT 4000
Material Group Gr. N° VDIGroup
Material Examples Hardness
profiling slotting fz[mm/tooth] Vc [m/min]
ap ae ap Ø 8.0 Ø 10.0 Ø12.0 min max
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
372
SOLID END MILL
L2
L1
D2 D1
4 fl
unequal
38°-41°
variable
E90 Z4 D03.0(06) L12.0(050) LT 4000 3.0 6 50 12.0 M5003559 E90 Z4 D04.0(06) L16.0(055) LT 4000 4.0 6 55 16.0 M5003560
E90 Z4 D05.0(06) L20.0(060) LT 4000 5.0 6 60 20.0 M5003561 E90 Z4 D06.0(06) L24.0(065) LT 4000 6.0 6 65 24.0 M5003562
E90 Z4 D08.0(08) L32.0(090) LT 4000 8.0 8 90 32.0 M5003563 E90 Z4 D10.0(10) L40.0(100) LT 4000 10.0 10 100 40.0 M5003564
E90 Z4 D12.0(12) L48.0(110) LT 4000 12.0 12 110 48.0 M5003565
E90 Z4 D16.0(16) L64.0(160) LT 4000 16.0 16 160 64.0 M5003566
Product Designation D1 Catalog Nr.L2D2 L1
90° 4 Flutes, Long
373
SOLID END MILL
1 125 HB 3.0xØ 0.25xØ 1.0xØ 0.010 0.011 0.016 0.023 0.029 150 200
2 190 HB 3.0xØ 0.25xØ 1.0xØ 0.010 0.011 0.016 0.023 0.029 140 190
3 250 HB 3.0xØ 0.25xØ 1.0xØ 0.010 0.011 0.016 0.023 0.029 120 160
6 180 HB 3.0xØ 0.25xØ 1.0xØ 0.008 0.010 0.014 0.020 0.025 120 180
4,6 230 HB 3.0xØ 0.25xØ 1.0xØ 0.008 0.010 0.014 0.020 0.025 90 130
5,7 280 HB 3.0xØ 0.25xØ 0.7xØ 0.007 0.008 0.011 0.016 0.020 80 120
8 350 HB 3.0xØ 0.25xØ 0.7xØ 0.007 0.008 0.011 0.016 0.020 60 90
10 220 HB 3.0xØ 0.25xØ 0.7xØ 0.007 0.008 0.011 0.016 0.020 70 130
10 280 HB 3.0xØ 0.25xØ 0.7xØ 0.007 0.008 0.011 0.016 0.020 65 110
11 320 HB 3.0xØ 0.25xØ 0.5xØ 0.005 0.006 0.008 0.011 0.014 60 90
11 350 HB 3.0xØ 0.25xØ 0.5xØ 0.005 0.006 0.008 0.011 0.014 50 80
14 180 HB 3.0xØ 0.25xØ 1.0xØ 0.006 0.007 0.010 0.015 0.019 80 120
14 240 HB 3.0xØ 0.25xØ 1.0xØ 0.005 0.007 0.010 0.015 0.019 70 115
14 290 HB 3.0xØ 0.25xØ 1.0xØ 0.005 0.006 0.008 0.011 0.014 60 100
14 310 HB 3.0xØ 0.25xØ 1.0xØ 0.005 0.006 0.008 0.011 0.014 60 90
12 200 HB 3.0xØ 0.25xØ 1.0xØ 0.005 0.005 0.008 0.011 0.014 50 90
13 42 HRc 3.0xØ 0.25xØ 1.0xØ 0.005 0.005 0.008 0.011 0.014 30 55
15 150 HB 3.0xØ 0.25xØ 1.0xØ 0.009 0.011 0.015 0.022 0.027 140 200
15 200 HB 3.0xØ 0.25xØ 1.0xØ 0.009 0.011 0.015 0.022 0.027 150 190
16 250 HB 3.0xØ 0.25xØ 1.0xØ 0.009 0.011 0.015 0.022 0.027 120 160
17,19 150 HB 3.0xØ 0.25xØ 1.0xØ 0.009 0.010 0.014 0.021 0.026 130 180
17,19 200 HB 3.0xØ 0.25xØ 1.0xØ 0.009 0.010 0.014 0.021 0.026 110 150
18,20 250 HB 3.0xØ 0.25xØ 1.0xØ 0.009 0.010 0.014 0.021 0.026 90 130
31,32 Incoloy 800 240 HB 3.0xØ 0.10xØ 1.0xØ 0.004 0.004 0.006 0.009 0.011 30 50
33 Inconel 700 250 HB 3.0xØ 0.10xØ 1.0xØ 0.004 0.004 0.006 0.009 0.011 25 45
34 Stellite 21 350 HB 3.0xØ 0.10xØ 1.0xØ 0.004 0.004 0.006 0.009 0.011 20 50
36 TiAl6V4 - 3.0xØ 0.25xØ 1.0xØ 0.004 0.004 0.006 0.009 0.011 30 60
37 T40 - 3.0xØ 0.25xØ 1.0xØ 0.004 0.004 0.006 0.009 0.011 40 70
38 45 HRc 3.0xØ 0.10xØ 0.1xØ 0.003 0.004 0.006 0.008 0.010 40 60
38 50 HRc 3.0xØ 0.10xØ 0.1xØ 0.003 0.004 0.006 0.008 0.010 35 55
38 55 HRc 3.0xØ 0.10xØ 0.1xØ 0.003 0.003 0.005 0.007 0.009 30 50
Chilled Cast Iron 40 Ni-Hard 2 400 HB 3.0xØ 0.10xØ 0.1xØ 0.003 0.003 0.005 0.007 0.009 35 55
White Cast Iron 41 G-X300CrMo15 55 HRc 3.0xØ 0.10xØ 0.1xØ 0.003 0.003 0.005 0.007 0.009 30 50
NF AAl (>8%Si) 12 25 AlSi12 130 HB 3.0xØ 0.25xØ 1.0xØ 0.010 0.011 0.016 0.023 0.029 160 250
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Steel
11
GGG40, GGG70, 50005
HTA
Fe, Ni & Co based
9
Ti based
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular
10
8
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6Stee
l
Non-alloyed
Low alloyed
High alloyed 3
Stai
nles
s St
eel
X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430
Austenitic 4304, 316,
X5CrNi18-9
Duplex
E90° Z4 Long Ø 1 - 5 – LT 4000
Material Group Gr. N° VDIGroup
Material Examples Hardness
profiling slotting fz[mm/tooth] Vc [m/min]
ap ae ap Ø 1.0 Ø 2.0 Ø3.0 Ø4.0 Ø5.0 min max
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Machining Conditions
374
SOLID END MILL
1 125 HB 3.0xØ 0.25xØ 1.0xØ 0.036 0.050 0.059 0.070 150 200
2 190 HB 3.0xØ 0.25xØ 1.0xØ 0.036 0.050 0.059 0.070 140 190
3 250 HB 3.0xØ 0.25xØ 1.0xØ 0.036 0.050 0.059 0.070 120 160
6 180 HB 3.0xØ 0.25xØ 1.0xØ 0.032 0.044 0.053 0.062 120 180
4,6 230 HB 3.0xØ 0.25xØ 1.0xØ 0.032 0.044 0.053 0.062 90 130
5,7 280 HB 3.0xØ 0.25xØ 0.7xØ 0.026 0.035 0.042 0.049 80 120
8 350 HB 3.0xØ 0.25xØ 0.7xØ 0.026 0.035 0.042 0.049 60 90
10 220 HB 3.0xØ 0.25xØ 0.7xØ 0.026 0.035 0.042 0.049 70 130
10 280 HB 3.0xØ 0.25xØ 0.7xØ 0.026 0.035 0.042 0.049 65 110
11 320 HB 3.0xØ 0.25xØ 0.5xØ 0.018 0.025 0.030 0.035 60 90
11 350 HB 3.0xØ 0.25xØ 0.5xØ 0.018 0.025 0.030 0.035 50 80
14 180 HB 3.0xØ 0.25xØ 1.0xØ 0.024 0.032 0.039 0.045 80 120
14 240 HB 3.0xØ 0.25xØ 1.0xØ 0.024 0.032 0.039 0.045 70 115
14 290 HB 3.0xØ 0.25xØ 1.0xØ 0.018 0.025 0.030 0.035 60 100
14 310 HB 3.0xØ 0.25xØ 1.0xØ 0.018 0.025 0.030 0.035 60 90
12 200 HB 3.0xØ 0.25xØ 1.0xØ 0.017 0.024 0.029 0.033 50 90
13 42 HRc 3.0xØ 0.25xØ 1.0xØ 0.017 0.024 0.029 0.033 30 55
15 150 HB 3.0xØ 0.25xØ 1.0xØ 0.035 0.047 0.056 0.066 140 200
15 200 HB 3.0xØ 0.25xØ 1.0xØ 0.035 0.047 0.056 0.066 150 190
16 250 HB 3.0xØ 0.25xØ 1.0xØ 0.035 0.047 0.056 0.066 120 160
17,19 150 HB 3.0xØ 0.25xØ 1.0xØ 0.033 0.045 0.053 0.063 130 180
17,19 200 HB 3.0xØ 0.25xØ 1.0xØ 0.033 0.045 0.053 0.063 110 150
18,20 250 HB 3.0xØ 0.25xØ 1.0xØ 0.033 0.045 0.053 0.063 90 130
31,32 Incoloy 800 240 HB 3.0xØ 0.10xØ 1.0xØ 0.015 0.020 0.024 0.028 30 50
33 Inconel 700 250 HB 3.0xØ 0.10xØ 1.0xØ 0.015 0.020 0.024 0.028 25 45
34 Stellite 21 350 HB 3.0xØ 0.10xØ 1.0xØ 0.015 0.020 0.024 0.028 20 50
36 TiAl6V4 - 3.0xØ 0.25xØ 1.0xØ 0.015 0.020 0.024 0.028 30 60
37 T40 - 3.0xØ 0.25xØ 1.0xØ 0.015 0.020 0.024 0.028 40 70
38 45 HRc 3.0xØ 0.10xØ 0.1xØ 0.013 0.017 0.021 0.024 40 60
38 50 HRc 3.0xØ 0.10xØ 0.1xØ 0.013 0.017 0.021 0.024 35 55
38 55 HRc 3.0xØ 0.10xØ 0.1xØ 0.011 0.015 0.018 0.021 30 50
Chilled Cast Iron 40 Ni-Hard 2 400 HB 3.0xØ 0.10xØ 0.1xØ 0.011 0.015 0.018 0.021 35 55
White Cast Iron 41 G-X300CrMo15 55 HRc 3.0xØ 0.10xØ 0.1xØ 0.011 0.015 0.018 0.021 30 50
NF Al (>8%Si) 12 25 AlSi12 130 HB 3.0xØ 0.25xØ 1.0xØ 0.036 0.050 0.059 0.070 160 250
X100CrMo13, 440C,
G-X260NiCr42 11
GGG40, GGG70, 50005
9
7 GG20, GG40, EN-GJL-250,
No30B
10
8
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
3X40CrMoV5,
H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
4304, 316,
X5CrNi18-9
E90° Z4 Long Ø 6, 8, 10, 12 – LT 4000
Material Group Gr. N° VDIGroup
Material Examples Hardness
profiling slotting fz[mm/tooth] Vc [m/min]
ap ae ap Ø 6.0 Ø 8.0 Ø10.0 Ø12.0 min max
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Machining Conditions
375
SOLID END MILL
45°
4 fl
L2
L1
D2 D1
L2
L1
D2 D1
ERO Z3 D04.0(06) L11.0(057) LT 4000 4.0 6 57 11.0 M5003607
ERO Z4 D05.0(06) L13.0(057) LT 4000 5.0 6 57 13.0 M5003608
ERO Z4 D06.0(06) L13.0(057) LT 4000 6.0 6 57 13.0 M5003609 ERO Z4 D08.0(08) L19.0(063) LT 4000 8.0 8 63 19.0 M5003610
ERO Z4 D10.0(10) L22.0(072) LT 4000 10.0 10 72 22.0 M5003611 ERO Z4 D12.0(12) L26.0(083) LT 4000 12.0 12 83 26.0 M5003612
Product Designation
Product Designation
D1
D1
Catalog Nr.
Catalog Nr.
L2
L2
D2
D2
L1
L1
90° 3 Flutes, Rougher
90° 4 Flutes, Rougher
376
SOLID END MILL
1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.024 0.030 0.040 150 200
2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.024 0.030 0.040 140 190
3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.024 0.030 0.040 120 160
6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.025 0.030 0.039 120 180
4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.025 0.030 0.039 90 130
5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.020 0.024 0.032 80 120
8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.020 0.024 0.032 60 90
10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.026 0.033 70 130
10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.026 0.033 65 110
11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.016 0.020 0.025 60 90
11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.016 0.020 0.025 50 80
14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.022 0.028 80 120
14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.022 0.028 70 115
14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.013 0.017 0.021 60 100
14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.013 0.017 0.021 60 90
12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.013 0.017 0.021 50 90
13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.013 0.017 0.021 30 55
15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.029 0.036 0.047 140 200
15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.029 0.036 0.047 150 190
16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.029 0.036 0.047 120 160
17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.025 0.031 0.040 130 180
17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.025 0.031 0.040 110 150
18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.025 0.031 0.040 90 130
31,32 Incoloy 800 240 HB 1.5xØ 0.3xØ 1.0xØ 0.014 0.018 0.023 30 50
33 Inconel 700 250 HB 1.5xØ 0.3xØ 1.0xØ 0.014 0.018 0.023 25 45
34 Stellite 21 350 HB 1.5xØ 0.3xØ 1.0xØ 0.014 0.018 0.023 20 50
36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.015 0.018 0.023 30 60
37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.015 0.018 0.023 40 70
38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.011 0.013 0.017 40 60
38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.011 0.013 0.017 35 55
38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.008 0.010 0.013 30 50
Chilled Cast Iron 40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.008 0.010 0.013 35 55
White Cast Iron 41 G-X300CrMo15 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.008 0.010 0.013 30 50
NF Al (>8%Si) 12 25 AlSi12 130 HB 1.5xØ 0.5xØ 1.0xØ 0.027 0.033 0.042 160 250
11
GGG40, GGG70, 50005
9
7 GG20, GG40, EN-GJL-250,
No30B
10
8
X100CrMo13, 440C,
G-X260NiCr42
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
3
6 410, X6Cr17, 17-4 PH, 430
4304, 316,
X5CrNi18-9
ERO Z4 Ø 4, 5, 6 – LT 4000
Material Group Gr. N° VDIGroup
Material Examples Hardness
profiling slotting fz[mm/tooth] Vc [m/min]
ap ae ap Ø 4.0 Ø 5.0 Ø6.0 min max
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Machining Conditions
377
SOLID END MILL
1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.055 0.065 0.077 150 200
2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.055 0.065 0.077 140 190
3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.055 0.065 0.077 120 160
6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.053 0.063 0.074 120 180
4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.053 0.063 0.074 90 130
5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.043 0.052 0.062 80 120
8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.043 0.052 0.062 60 90
10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.046 0.055 0.064 70 130
10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.046 0.055 0.064 65 110
11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.035 0.041 0.049 60 90
11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.035 0.041 0.049 50 80
14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.038 0.045 0.053 80 120
14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.038 0.045 0.053 70 115
14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.029 0.035 0.040 60 100
14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.029 0.035 0.040 60 90
12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.029 0.035 0.040 50 90
13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.029 0.035 0.040 30 55
15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.064 0.076 0.089 140 200
15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.064 0.076 0.089 150 190
16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.064 0.076 0.089 120 160
17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.055 0.066 0.077 130 180
17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.055 0.066 0.077 110 150
18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.055 0.066 0.077 90 130
31,32 Incoloy 800 240 HB 1.5xØ 0.3xØ 1.0xØ 0.031 0.037 0.044 30 50
33 Inconel 700 250 HB 1.5xØ 0.3xØ 1.0xØ 0.031 0.037 0.044 25 45
34 Stellite 21 350 HB 1.5xØ 0.3xØ 1.0xØ 0.031 0.037 0.044 20 50
36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.032 0.038 0.045 30 60
37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.032 0.038 0.045 40 70
38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.023 0.028 0.032 40 60
38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.023 0.028 0.032 35 55
38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.017 0.021 0.024 30 50
Chilled Cast Iron 40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.017 0.021 0.024 35 55
White Cast Iron 41 G-X300CrMo15 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.017 0.021 0.024 30 50
NF Al (>8%Si) 12 25 AlSi12 130 HB 1.5xØ 0.5xØ 1.0xØ 0.058 0.069 0.081 160 250
11
GGG40, GGG70, 50005
9
7 GG20, GG40, EN-GJL-250,
No30B
10
8
X100CrMo13, 440C,
G-X260NiCr42
1C35, Ck45, 1020, 1045, 1060, 28Mn6
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
2
X2CrNiN23-4, S31500
3
6 410, X6Cr17, 17-4 PH, 430
4304, 316,
X5CrNi18-9
ERO Z4 Ø 8, 10, 12 – LT 4000
Material Group Gr. N° VDIGroup
Material Examples Hardness
profiling slotting fz[mm/tooth] Vc [m/min]
ap ae ap Ø 8.0 Ø 10.0 Ø12.0 min max
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Machining Conditions
378
SOLID END MILL
L2
L1
D2 D1
R
L2
L1
D2 D1
R
2 fl
30°
EBN Z2 D01.0(03) L03.0(038) R0.50 LT 4000 1.0 3 38 3.0 0.50 M5003587
EBN Z2 D01.5(03) L05.0(038) R0.75 LT 4000 1.5 3 38 5.0 0.75 M5003588 EBN Z2 D02.0(03) L06.0(038) R1.00 LT 4000 2.0 3 38 6.0 1.0 0 M5003589
EBN Z2 D02.5(03) L07.0(038) R1.25 LT 4000 2.5 3 38 7.0 1.25 M5003590 EBN Z2 D03.0(03) L09.0(038) R1.50 LT 4000 3.0 3 38 9.0 1.50 M5003591
EBN Z2 D04.0(04) L14.0(050) R2.00 LT 4000 4.0 4 50 14.0 2.00 M5003592 EBN Z2 D05.0(05) L16.0(050) R2.50 LT 4000 5.0 5 50 16.0 2.50 M5003593
EBN Z2 D06.0(06) L20.0(063) R3.00 LT 4000 6.0 6 63 20.0 3.00 M5003594 EBN Z2 D08.0(08) L20.0(063) R4.00 LT 4000 8.0 8 63 20.0 4.00 M5003595
EBN Z2 D10.0(10) L22.0(072) R5.00 LT 4000 10.0 10 72 22.0 5.00 M5003596 EBN Z2 D12.0(12) L26.0(075) R6.00 LT 4000 12.0 12 75 26.0 6.00 M5003597
Product Designation D1 Catalog Nr.L2 RD2 L1
Ball Nose, 2 Flutes
379
SOLID END MILL
1 125 HB 0.25xØ 0.7xØ 0.035 0.045 0.065 0.080 0.105 150 200
2 190 HB 0.25xØ 0.7xØ 0.035 0.045 0.065 0.080 0.105 140 190
3 250 HB 0.25xØ 0.7xØ 0.035 0.045 0.065 0.080 0.105 120 160
6 180 HB 0.25xØ 0.7xØ 0.033 0.042 0.061 0.075 0.099 120 180
4,6 230 HB 0.25xØ 0.7xØ 0.033 0.042 0.061 0.075 0.099 90 130
5,7 280 HB 0.25xØ 0.7xØ 0.028 0.036 0.052 0.064 0.084 80 120
8 350 HB 0.25xØ 0.7xØ 0.028 0.036 0.052 0.064 0.084 60 90
10 220 HB 0.25xØ 0.7xØ 0.028 0.036 0.051 0.063 0.083 70 130
10 280 HB 0.25xØ 0.7xØ 0.028 0.036 0.051 0.063 0.083 65 110
11 320 HB 0.25xØ 0.7xØ 0.021 0.027 0.039 0.048 0.063 60 90
11 350 HB 0.25xØ 0.7xØ 0.021 0.027 0.039 0.048 0.063 50 80
14 180 HB 0.25xØ 0.7xØ 0.023 0.029 0.042 0.052 0.068 80 120
14 240 HB 0.25xØ 0.7xØ 0.023 0.029 0.042 0.052 0.068 70 115
14 290 HB 0.25xØ 0.7xØ 0.018 0.023 0.033 0.040 0.053 60 100
14 310 HB 0.25xØ 0.7xØ 0.018 0.023 0.033 0.040 0.053 60 90
12 200 HB 0.25xØ 0.7xØ 0.024 0.031 0.044 0.054 0.071 50 90
13 42 HRc 0.25xØ 0.7xØ 0.024 0.031 0.044 0.054 0.071 30 55
15 150 HB 0.25xØ 0.7xØ 0.039 0.050 0.072 0.088 0.116 140 200
15 200 HB 0.25xØ 0.7xØ 0.039 0.050 0.072 0.088 0.116 150 190
16 250 HB 0.25xØ 0.7xØ 0.039 0.050 0.072 0.088 0.116 120 160
17,19 150 HB 0.25xØ 0.7xØ 0.033 0.043 0.062 0.076 0.100 130 180
17,19 200 HB 0.25xØ 0.7xØ 0.033 0.043 0.062 0.076 0.100 110 150
18,20 250 HB 0.25xØ 0.7xØ 0.033 0.043 0.062 0.076 0.100 90 130
31,32 Incoloy 800 240 HB 0.25xØ 0.6xØ 0.022 0.029 0.042 0.051 0.067 30 50
33 Inconel 700 250 HB 0.25xØ 0.6xØ 0.022 0.029 0.042 0.051 0.067 25 45
34 Stellite 21 350 HB 0.25xØ 0.6xØ 0.022 0.029 0.042 0.051 0.067 20 50
36 TiAl6V4 - 0.25xØ 0.7xØ 0.019 0.025 0.036 0.044 0.058 30 60
37 T40 - 0.25xØ 0.7xØ 0.019 0.025 0.036 0.044 0.058 40 70
38 45 HRc 0.25xØ 0.6xØ 0.014 0.018 0.026 0.032 0.042 40 60
38 50 HRc 0.25xØ 0.6xØ 0.014 0.018 0.026 0.032 0.042 35 55
38 55 HRc 0.25xØ 0.3xØ 0.011 0.014 0.020 0.024 0.032 30 50
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.25xØ 0.3xØ 0.011 0.014 0.020 0.024 0.032 35 55
White Cast Iron 41 G-X300CrMo15 55 HRc 0.25xØ 0.3xØ 0.011 0.014 0.020 0.024 0.032 30 50
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.25xØ 0.7xØ 0.035 0.045 0.065 0.080 0.105 160 250
3
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
4304, 316,
X5CrNi18-9
11
GGG40, GGG70, 50005
9
7 GG20, GG40, EN-GJL-250,
No30B
10
8
X100CrMo13, 440C,
G-X260NiCr42
EBN Z2 Ø 1 - 5 – LT 4000
Material Group Gr. N° VDIGroup
Material Examples Hardness
contouring fz[mm/tooth] Vc [m/min]
ap ae Ø1.0 Ø2.0 Ø 3.0 Ø 4.0 Ø 5.0 min max
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Machining Conditions
380
SOLID END MILL
1 125 HB 0.25xØ 0.7xØ 0.100 0.115 0.125 0.140 150 200
2 190 HB 0.25xØ 0.7xØ 0.100 0.115 0.125 0.140 140 190
3 250 HB 0.25xØ 0.7xØ 0.100 0.115 0.125 0.140 120 160
6 180 HB 0.25xØ 0.7xØ 0.094 0.108 0.118 0.132 120 180
4,6 230 HB 0.25xØ 0.7xØ 0.094 0.108 0.118 0.132 90 130
5,7 280 HB 0.25xØ 0.7xØ 0.080 0.092 0.100 0.112 80 120
8 350 HB 0.25xØ 0.7xØ 0.080 0.092 0.100 0.112 60 90
10 220 HB 0.25xØ 0.7xØ 0.079 0.091 0.099 0.111 70 130
10 280 HB 0.25xØ 0.7xØ 0.079 0.091 0.099 0.111 65 110
11 320 HB 0.25xØ 0.7xØ 0.060 0.069 0.075 0.084 60 90
11 350 HB 0.25xØ 0.7xØ 0.060 0.069 0.075 0.084 50 80
14 180 HB 0.25xØ 0.7xØ 0.065 0.075 0.081 0.091 80 120
14 240 HB 0.25xØ 0.7xØ 0.065 0.075 0.081 0.091 70 115
14 290 HB 0.25xØ 0.7xØ 0.050 0.058 0.063 0.070 60 100
14 310 HB 0.25xØ 0.7xØ 0.050 0.058 0.063 0.070 60 90
12 200 HB 0.25xØ 0.7xØ 0.068 0.078 0.085 0.095 50 90
13 42 HRc 0.25xØ 0.7xØ 0.068 0.078 0.085 0.095 30 55
15 150 HB 0.25xØ 0.7xØ 0.110 0.127 0.138 0.154 140 200
15 200 HB 0.25xØ 0.7xØ 0.110 0.127 0.138 0.154 150 190
16 250 HB 0.25xØ 0.7xØ 0.110 0.127 0.138 0.154 120 160
17,19 150 HB 0.25xØ 0.7xØ 0.095 0.109 0.119 0.133 130 180
17,19 200 HB 0.25xØ 0.7xØ 0.095 0.109 0.119 0.133 110 150
18,20 250 HB 0.25xØ 0.7xØ 0.095 0.109 0.119 0.133 90 130
31,32 Incoloy 800 240 HB 0.25xØ 0.6xØ 0.064 0.074 0.080 0.090 30 50
33 Inconel 700 250 HB 0.25xØ 0.6xØ 0.064 0.074 0.080 0.090 25 45
34 Stellite 21 350 HB 0.25xØ 0.6xØ 0.064 0.074 0.080 0.090 20 50
36 TiAl6V4 - 0.25xØ 0.7xØ 0.055 0.063 0.069 0.077 30 60
37 T40 - 0.25xØ 0.7xØ 0.055 0.063 0.069 0.077 40 70
38 45 HRc 0.25xØ 0.6xØ 0.040 0.046 0.050 0.056 40 60
38 50 HRc 0.25xØ 0.6xØ 0.040 0.046 0.050 0.056 35 55
38 55 HRc 0.25xØ 0.3xØ 0.030 0.035 0.038 0.042 30 50
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.25xØ 0.3xØ 0.030 0.035 0.038 0.042 35 55
White Cast Iron 41 G-X300CrMo15 55 HRc 0.25xØ 0.3xØ 0.030 0.035 0.038 0.042 30 50
NF Al (>8%Si) 12 25 AlSi12 130 HB 0.25xØ 0.7xØ 0.100 0.115 0.125 0.140 160 250
3
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
5
1C35, Ck45, 1020, 1045, 1060, 28Mn6
2
X2CrNiN23-4, S31500
6 410, X6Cr17, 17-4 PH, 430
4304, 316,
X5CrNi18-9
11
GGG40, GGG70, 50005
9
7 GG20, GG40, EN-GJL-250,
No30B
10
8
X100CrMo13, 440C,
G-X260NiCr42
EBN Z2 Ø 6, 8, 10, 12 – LT 4000
Material Group Gr. N° VDIGroup
Material Examples Hardness
contouring fz[mm/tooth] Vc [m/min]
ap ae Ø 6.0 Ø 8.0 Ø 10.0 Ø 12.0 min max
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Stai
nles
s St
eel Austenitic
Duplex
Ferritic & Martensitic
Cast
Iron
Grey
Malleable & Nodular
High
Tem
p. A
lloys
Fe, Ni & Co Based
Ti Based
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
NF Al (>8%Si)
Machining Conditions
381
SOLID END MILL
L2
L1
D2 D1
R
0°
4 fl
EHF Z4 D03.0(06) L02.0(070) R0.37 LT 4000 3.0 6 70 2.0 M5003600
EHF Z4 D04.0(06) L02.0(070) R0.47 LT 4000 4.0 6 70 2.0 M5003601 EHF Z4 D05.0(06) L02.5(070) R0.60 LT 4000 5.0 6 70 2.5 M5003602
EHF Z4 D06.0(06) L03.0(070) R0.73 LT 4000 6.0 6 70 3.0 M5003603 EHF Z4 D08.0(08) L04.0(080) R0.98 LT 4000 8.0 8 80 4.0 M5003604
EHF Z4 D10.0(10) L05.0(090) R1.23 LT 4000 10.0 10 90 5.0 M5003605
EHF Z4 D12.0(12) L06.0(100) R1.65 LT 4000 12.0 12 100 6.0 M5003606
Product Designation D1 Catalog Nr.L2D2 L1
High Feed, 4 Flutes
382
SOLID END MILL
1 125 HB 0.025xØ 0.5xØ 0.140 0.200 0.240 150 200
2 190 HB 0.025xØ 0.5xØ 0.140 0.200 0.240 140 190
3 250 HB 0.025xØ 0.5xØ 0.140 0.200 0.240 120 160
6 180 HB 0.025xØ 0.5xØ 0.132 0.188 0.226 120 180
4,6 230 HB 0.025xØ 0.5xØ 0.132 0.188 0.226 90 130
5,7 280 HB 0.025xØ 0.5xØ 0.132 0.188 0.226 80 120
8 350 HB 0.025xØ 0.5xØ 0.132 0.188 0.226 60 90
10 220 HB 0.025xØ 0.5xØ 0.111 0.158 0.190 70 130
10 280 HB 0.025xØ 0.5xØ 0.111 0.158 0.190 65 110
11 320 HB 0.025xØ 0.5xØ 0.084 0.120 0.144 60 90
11 350 HB 0.025xØ 0.5xØ 0.084 0.120 0.144 50 80
15 150 HB 0.025xØ 0.5xØ 0.154 0.220 0.264 140 200
15 200 HB 0.025xØ 0.5xØ 0.154 0.220 0.264 150 190
16 250 HB 0.025xØ 0.5xØ 0.154 0.220 0.264 120 160
17,19 150 HB 0.025xØ 0.5xØ 0.133 0.190 0.228 130 180
17,19 200 HB 0.025xØ 0.5xØ 0.133 0.190 0.228 110 150
18,20 250 HB 0.025xØ 0.5xØ 0.133 0.190 0.228 90 130
38 45 HRc 0.025xØ 0.5xØ 0.070 0.100 0.120 40 60
38 50 HRc 0.025xØ 0.5xØ 0.070 0.100 0.120 35 55
38 55 HRc 0.025xØ 0.3xØ 0.056 0.080 0.096 30 50
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.025xØ 0.3xØ 0.056 0.080 0.096 35 55
White Cast Iron 41 G-X300CrMo15 55 HRc 0.025xØ 0.3xØ 0.056 0.080 0.096 30 50
X100CrMo13, 440C,
G-X260NiCr42
Hard
ened
Steel
11
GGG40, GGG70, 50005
Cast
Iron
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
1C35, Ck45, 1020, 1045, 1060, 28Mn6
St
eel
Non-alloyed
Low alloyed
High alloyed 3
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
2
EHF Z4 Ø 3 - 5 – LT 4000
1 125 HB 0.025xØ 0.5xØ 0.260 0.340 0.400 0.450 150 200
2 190 HB 0.025xØ 0.5xØ 0.260 0.340 0.400 0.450 140 190
3 250 HB 0.025xØ 0.5xØ 0.260 0.340 0.400 0.450 120 160
6 180 HB 0.025xØ 0.5xØ 0.244 0.320 0.376 0.423 120 180
4,6 230 HB 0.025xØ 0.5xØ 0.244 0.320 0.376 0.423 90 130
5,7 280 HB 0.025xØ 0.5xØ 0.244 0.320 0.376 0.423 80 120
8 350 HB 0.025xØ 0.5xØ 0.244 0.320 0.376 0.423 60 90
10 220 HB 0.025xØ 0.5xØ 0.205 0.269 0.316 0.356 70 130
10 280 HB 0.025xØ 0.5xØ 0.205 0.269 0.316 0.356 65 110
11 320 HB 0.025xØ 0.5xØ 0.156 0.204 0.240 0.270 60 90
11 350 HB 0.025xØ 0.5xØ 0.156 0.204 0.240 0.270 50 80
15 150 HB 0.025xØ 0.5xØ 0.286 0.374 0.440 0.495 140 200
15 200 HB 0.025xØ 0.5xØ 0.286 0.374 0.440 0.495 150 190
16 250 HB 0.025xØ 0.5xØ 0.286 0.374 0.440 0.495 120 160
17,19 150 HB 0.025xØ 0.5xØ 0.247 0.323 0.380 0.428 130 180
17,19 200 HB 0.025xØ 0.5xØ 0.247 0.323 0.380 0.428 110 150
18,20 250 HB 0.025xØ 0.5xØ 0.247 0.323 0.380 0.428 90 130
38 45 HRc 0.025xØ 0.5xØ 0.130 0.170 0.200 0.225 40 60
38 50 HRc 0.025xØ 0.5xØ 0.130 0.170 0.200 0.225 35 55
38 55 HRc 0.025xØ 0.3xØ 0.104 0.136 0.160 0.180 30 50
Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.025xØ 0.3xØ 0.104 0.136 0.160 0.180 35 55
White Cast Iron 41 G-X300CrMo15 55 HRc 0.025xØ 0.3xØ 0.104 0.136 0.160 0.180 30 50
X100CrMo13, 440C,
G-X260NiCr42
Har
dene
d Steel
11
GGG40, GGG70, 50005
Cas
t Iro
n
Grey 7 GG20, GG40, EN-GJL-250,
No30B
Malleable & Nodular 8
1C35, Ck45, 1020, 1045, 1060, 28Mn6
St
eel
Non-alloyed
Low alloyed
High alloyed 3
42CrMo4, St50, Ck60, 4140, 4340,
100Cr6
X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19
2
EHF Z4 Ø 6, 8,10,12 – LT 4000
Material Group Gr. N° VDIGroup
Material Examples Hardness
contouring fz[mm/tooth] Vc [m/min]
ap ae Ø 3.0 Ø 4.0 Ø 5.0 min max
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Cast
Iron
Grey
Malleable & Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
Material Group Gr. N° VDIGroup
Material Examples Hardness
contouring fz[mm/tooth] Vc [m/min]
ap ae Ø 6.0 Ø 8.0 Ø10.0 Ø12.0 min max
Non Alloyed
Stee
l Low Alloyed
High Alloyed
Cast
Iron
Grey
Malleable & Nodular
Hard
ened
Mat
.
Steel
Chilled Cast Iron
White Cast Iron
Machining Conditions
383
MATERIALS REFERENCE LIST
Material Reference List
384
MATERIALS REFERENCE LIST
385
MATERIALS REFERENCE LIST
386
MATERIALS REFERENCE LIST
387
MATERIALS REFERENCE LIST
388
MATERIALS REFERENCE LIST