l sheet metal mounting plates, brackets - th.misumi-ec.com · 2 -1853 1853-1854_f60-012_ceng 2...
TRANSCRIPT
-18532
1853-1854_F60-012_cENG
-18542
1853-1854_F60-012_cENG cENG 2nd
L Sheet Metal Mounting Plates, BracketsDimension Configurable Type
Part Number MMaterial SSurface TreatmentType Material Symbol
FALZSFALAS FAPASFALCS FADASFALDS FADBSFACAS FAMDSFALBS FAEASFASBS FAMBSFAMAS FANASFAMCS FATBS
SP
SPCCE
-
SPB Black Oxide
SPU Trivalent Chromate (Clear)
SPK Trivalent Chromate (Black)
AMA5052
-
AMW Anodize (Clear)
AMB Anodize (Black)
SUD SUS304(2B) -
E�4.5, 6.0 thickness type is SPHC material.
EAs opposed to the "Center Symmetrical Type" on the previous page, general tolerance is the guaranteed value for external dimensions.
Part Number- T - A - B - L - X - F - H - G - Hole Specification1
Code, Nominal Value - D - J - Y - V - S - W - Hole Specification2 Code, Nominal Value - K
Type - Material Symbol
FALAS - SPB - T1.6 - A30 - B30 - L30 - X15 - H20 - N5 - Y15 - S15 - NA6FAMBS - AM - T1.5 - A80 - B60 - L60 - X50 - F0 - H70 - N4 - Y15 - V30 - S20 - W20 - NA5
E�There may be some hanger holes on anodized FALZS.(See Specifications and Machining Limits)
FALZS
FALAS FALCS FALDS FACAS
FALBS FASBS FAMAS FAMCS
FAPAS FADAS FADBS FAMDS
FAEAS FAMBS FANAS FATBS
E�Slotted hole direction can be changed (See alterations). E�Slotted hole direction can be changed (See alterations).
E�Slotted hole direction can be changed (See alterations). E�Slotted hole direction can be changed (See alterations).
E�Slotted hole direction can be changed (See alterations).E�Slotted hole direction can be changed (See alterations).
S
Y
X
H
LHole specification2NAMA
AB
Hole specification1
+0.2 0
NMDA
Hole specification2NA
X
HS
K
Y
Hole specification1NMDA
+0.2 0
X
HJ
Hole specification2NA
SK
Y
Hole specification1N
2 - Hole specification2NAMA
S
VY
AB
X
HS
VY
2 - Hole specification2NAMA
Hole specification1NMDA
L
+0.2 0
VY
X
KS
H
2 - Hole specification2NA
Hole specification1NMDA
+0.2 0
2 - Hole specification2NAMA
S
VY
FH
X
2 - Hole specification1NM
VY
KS
2 - Hole specification2NA
F
H
X
2 - Hole specification1NM
AB
F
HG
X2 - Hole specification1NM
2 - Hole specification2NAMA S
VY
L
HG
X2 - Hole specification1NM
2 - Hole specification2NAMA S
VY VY
KS
2 - Hole specification2NA
HG
X2 - Hole specification1NM
VY
KS
2 - Hole specification2NA
FJ
HX
2 - Hole specification1N
BA
X
H
Hole specification1NM
4 - Hole specification2NAMA
V
WS
Y
DA
L
+0.2 0
2 - Hole specification1
4 - Hole specification2
NM
NAMA
F
H
V
WS
X
Y
F
HG
X
4 - Hole specification2NAMA
V
WS
Y
4 - Hole specification1NM
H
G
FX
D
S
VY
4 - Hole specification1NM
2 - Hole specification2NAMA
+0.2 0
L
4-C2 or less
T
A
B
r
(Common Dimension)
eGreen colored parameters can be omitted. If the parameter setting is omitted, the holes will be evenly distributed about the center. For details, see dP.1834.
b
bbb f
g
bg
f
5 Ø3
5
QSpecifications, Machining LimitsE1. Burr height 0.1 or lessE2. Bend angle tolerance ±1°E3. There will be scratches and
bulges by Press Brake. For details and bend radius information, DP.1832.
E�4. Slotted holes may be shaped as shown below depending on dimensions. (No negative effects on mounting functionality) E6. There are machining limits on b, f, and g shown in below diagram.
For details, dP.1834.
E5. Anodized FALZS There are hanger holes above T4.
QHole Type Selection ChartHole Type Bolt Hole Tapped Holes (Coarse Thread) Through Hole
Code N, NA M, MA D, DA
Shape
Diagram
deMMA
D • DA +0.2 0
E�For d dimension, see "N, NA Machining Dimensions" on lower section of specification chart.
Part Number Selection 1mm IncrementX F H G
Hole Specification1D J Y V S W
Hole Specification2KType Material
Symbol T A B L Code Designation Code Designation
FALZSFALAS FAPASFALCS FADASFALDS FADBSFACAS FAMDSFALBS FAEASFASBS FAMBSFAMAS FANASFAMCS FATBS
SPSPBSPUSPKAM
AMWAMBSUD
SPCC(SPHC)
1.62.33.24.56.0
A5052
1.52.03.04.05.0
SUS304
1.01.52.03.04.05.0
20
~
200
EFor T6.0
~300
15
~
200
EFor T6.0
20~
10
~
200
EFor T6.0
20~
0.1mm Increment
N (Bolt Hole)E0, 3, 4, 5, 6, 8, 10
(Select)
3~30(0.5 Inc.)
0.1mm Increment
EJ≤Nx5
NA (Bolt Hole)E0, 3, 4, 56, 8, 10(Select) 0.1mm
Increment
EK≤NAx5
M (Tapped Holes)0, 3, 4, 5, 6, 8, 10
(Select) MA(Tapped Holes)
0, 3, 4, 56, 8, 10(Select)
DA (Through Hole)3~30
(0.5mm Increment)
EHoles may deform if the hole locations are too close to the ends and bends, but they will be machined as specified if they are within the machining limits.
EN, NA machining dimensions N, NA specified Value 0 3 4 5 6 8 10Through Hole Dia. (d) (No Hole) 3.5 4.5 5.5 6.5 9 11
Alterations
Slotted Hole Angle ChangeFALCS, FALDS FASBS, FAMCSFADBS, FAMDS
Code RC
Spec.
Slotted holes are changed as shown above.ENote the dimensions relationship
Add RC at the end of the type designation(Ex.)~-RC
S
B
Y
V
Y
S
B
Ordering Code
Part Number- T - A - B - L - X - F - H - G - Hole Specification1
Code, Nominal Value - D - J - Y - V - S - W - Hole Specification2
Code, Nominal Value - K - (RC)Type - Material Symbol
FALCS - SP - T1.6 - A30 - B30 - L30 - X15 - H20 - N5 - Y15 - S15 - NA3 - K2 - RC
A L T
Body Price Unit Price Surface Treatment Charge (Body Price+)
FALZS FALASFACAS
FALBSFALCS
FAMAS FAPASFASBS FADASFALDS FAEAS
FAMBS FAMCSFADBS FATBSFANAS FAMDS
SPCC A5052
SPCCSPHC A5052 SUS304 SPCC
SPHC A5052 SUS304 SPCCSPHC A5052 SUS304 SPCC
SPHC A5052 SUS304 SPCCSPHC A5052 SUS304
Black Oxide Trivalent
Chromate (Clear, Black)
Anodize (Clear)
Anodize (Black)
SP AM SUD SP AM SUD SP AM SUD SP AM SUD SP AM SUDSPBSPUSPK
AMW AMB
20~100
10~1001.0~1.62.0~3.24.0~6.0
101~2001.0~1.62.0~3.24.0~6.0
101~200
10~1001.0~1.62.0~3.24.0~6.0
101~2001.0~1.62.0~3.24.0~6.0
201~300 10~100 6.0 - - - - - - - - - - - -101~200 6.0 - - - - - - - - - - - -
• Price CalculationsAdd surface treatment charges to the body prices.(Ex.) For FALZS-SPU-T1.6-A100-B50-L50,
Main Body Price + Surface Treatment Charge = Price