kyo 4-8-32 programming manual
TRANSCRIPT
-
7/25/2019 Kyo 4-8-32 Programming Manual
1/52
-
7/25/2019 Kyo 4-8-32 Programming Manual
2/52
BENTEL SECURITY S.r.l. reserves the right to modify the technical specifications of this product without prior notice.
IMPORTANT: The following information is for disassembled Control Panels ONLY.
Ensure that the Manual you are using complies with the requirements (see below) on the
RELEASE ISSUES label inside the package. Upgrades of the KYO Unit Software Re-
lease are also suitable.
DO NOT attempt to assemble and install the Control Panel using a manual that does not
comply with requirements.
The Manual Release Number of each Manual is shown at the bottom of the last page,
between the Code and Date, as shown below.
-
7/25/2019 Kyo 4-8-32 Programming Manual
3/52
3
TABLEOFCONTENTS
Introduction .....................................................................5
Code Limitations ........................................................................... 5
Accepted Keypads ......................................................................... 6
Enrolling an LCD Keypad at Address 08 ...................................... 7
Adjusting Contrast, Brightness and Volume ................................ 7
The Liquid Crystal Display (LCD) ................................................. 8
Programming from the LCD Keypad .............................9
Customizing the System.................................................................... 9Exiting Programming ................................................................... 10
Programming .................................................................................... 10
Actions ......................................................................................... 10
Zones ........................................................................................... 11
Outputs......................................................................................... 13
Times ........................................................................................... 14
Installer Code .............................................................................. 16
Keys .............................................................................................. 16
Key/Card option ..................................................................... 16
Wireless option ..................................................................... 17
Codes ........................................................................................... 18
Readers ....................................................................................... 19
Keypads ....................................................................................... 20
Program option...................................................................... 20
Language option (Kyo32 and Kyo8W Series only) .............. 20
Date/Time .................................................................................... 21
Timers .......................................................................................... 21
Telephone .................................................................................... 22
Teleservice ................................................................................... 23Test Ev. ......................................................................................... 23
Events ........................................................................................... 24
Options......................................................................................... 25
Strings .......................................................................................... 26
Default .......................................................................................... 27
Input Expanders ........................................................................... 28
Output Expanders ........................................................................ 28
Programming from the LED Keypad ........................... 29
Accessing Programming................................................................. 29Exiting Programming ................................................................... 29
Programming .................................................................................... 30
Keypads ....................................................................................... 30
-
7/25/2019 Kyo 4-8-32 Programming Manual
4/52
4 Multifunction Control Panel
Readers ....................................................................................... 31Setting up the Zones ................................................................... 32
Setting up the Outputs ................................................................. 35
Setting up Times, Inactivity and Negligence .............................. 37
Telephone .................................................................................... 38
Setting up Teleservice and Test Event ........................................ 40
Events ........................................................................................... 41
Setting up the Scheduler ............................................................. 42
Options ......................................................................................... 43
Codes ........................................................................................... 45
Programming Keys and Cards ................................................... 46Extra Parameters ......................................................................... 48
Customized Protocol Parameters .............................................. 48
-
7/25/2019 Kyo 4-8-32 Programming Manual
5/52
5
Introduction
INTRODUCTION
You can program the system using the KyoUnit Software Application and a
computer (refer to the INSTALLATION MANUAL). You can also program somemodels from the KYO range via an LED Keypad (refer to the following Table).
This manual contains instructions regarding programming via Keypad. For
information regarding the system parameters, refer to PROGRAMMING
FROM PC in the INSTALLATION MANUAL.
Code Limitations
The INSTALLER Code can program the system but cannot program the PINS
of the 24 User Codes.
MAIN USER Codes can program the PINs of User Codes (but not other MainUser Codes) which operate on the Partitions they are assigned to.
In the Table below, Code 1 is a Main User Code assigned to Partitions 1, 3 and 4.
Therefore, it can program its own PIN (Code 1) and the PINs of: User Code 3
(assigned to Partitions 1 and 3), User Code 4 (assigned to Partition 4), User Code
5 (assigned to Partitions 3 and 4) and User Code 7 (assigned to Partition 3).
Code 2 is a Main User Code assigned to Partitions 2 and 3. Therefore, it can
program its own PIN, and the PINs of: Code 6 (assigned to Partition 2), User
Code 7 (assigned to Partition 3), User Code 8 (assigned to Partitions 2 and 3).
-
7/25/2019 Kyo 4-8-32 Programming Manual
6/52
6 Multifunction Control Panel
Accepted Keypads
You can program the system from OMNIA/TAST-R, MIA/S, MIA/D,
ALISON/S and ALISON/DVP LCDKeypads or, for KYO4-8 ONLY, from
LED Keypads. The Superkeys (function keys) on these Keypads differ
slightly. Table 2 shows how the keys function on the various Keypads.NOTE: The Superkeys must be duly setup, otherwise, they will NOT work.
The following Table shows the Superkeys (function keys) on the various
Keypads. The functions provided by keys , PpPpPpPpPp and (to bepressed contemporarily) on the MIA/S and MIA/D, are provided by pressing
and holding (respectively) keys 11111,22222and33333for approximately 3 seconds.
You can scroll the Programming menu, using keys99999and00000on the OMNIA/TAST-R Keypad, keysCCCCCandDDDDDon MIA/S and MIA/D Keypads, and CCCCC
and DDDDDon ALISON Keypads series.
-
7/25/2019 Kyo 4-8-32 Programming Manual
7/52
7
Introduction
Enrolling an LCD Keypad at Address 08
To enrol an LCD Keypad at Address 08 from a LED Keypad, enter:
+ OOOOO
A short beep will indicate that the LCD Keypad has been enrolled.
NOTE - You must enrol the LCD Keypad at Address 8 (using DIP switches
[51]), before completing the connection (refer to Table 2.1 or 2.2 in the IN-
STALLATION MANUAL).
The following procedure will allow you to change the Kyo Control panel
parameters when:
The Programming Software is not available.
A system, previously programmed via an LCD Keypad, must be repro-
grammed via an LED Keypad.
The system is equipped with LED Keypads only.
Before ending the Programming session, you must DISABLE the Keypad at
Address 8 or re-enable the LED Keypad (refer to the Keypads paragraph in
this section).
Adjusting Contrast, Brightness and Volume
NOTE - For MIA, ALISON/S and ALISON/DVP only.
You can change the Display Contrast and Brightness, and the Buzzer Volume.
Changes can be made during Standby status only.
Brightness Press and holdAAAAA(or A) to turn the Brightness up
Press and holdBBBBB(or B) to turn the Brightness down
Contrast Press and holdCCCCC(orC) to turn the Contrast up
Press and holdDDDDD(orD) to turn the Contrast down
Volume You can select 3 volume levels:High,MediumandMute.
Press eeeee(ore) until you obtain the required Volume level.
Long high Beep = High Volume
Long low Beep = Average Volume
Short low Beep = Mute
-
7/25/2019 Kyo 4-8-32 Programming Manual
8/52
8 Multifunction Control Panel
Figure 1 - An example of the Display during Standby status
The Liquid Crystal Display (LCD)
During Standby statusthe display will show:
1st line: Date and Time
2nd line: Partition status (4 or 8 Partitions depending on the system). This line
will also show:
Trouble and Tamper will be shown above the respective icon;
Special Functions *****will be shown above the respective icon ( tor r);
Telephone Line status will be shown above the iicon.
In the example in Figure 1, Partition 3 is armed, the 24h Tamper line is in
Alarm status, Teleservice is enabled and the Telephone line is busy.
-
7/25/2019 Kyo 4-8-32 Programming Manual
9/52
9
Programming from the LCD Keypad
The Installers Code will allow you to access theINSTALLER MENU and
program the following options:
Actions (Event Logger, Zones Status, Test Siren, Clear Call Queue)
Zones
Outputs
Times (Entry/Exit Times)
Inst.Cod (Installer Code)
Keys (Key/Card and Wireless)
Codes (User Codes)
Readers (Key/Card Readers)
Keypads (Keypads and Language)
Date/T. (Date and Time)
Timers (Scheduler)
Teleph. (Telephone numbers)
Teleser. (Teleservice)
Test Ev. (Test Call)
Events
Options
Strings (Descriptions)
Default (Restore Factory Default)
Exp. IN (Expander IN) ONLY Series 32 Models
Exp. OUT (Expander OUT) ONLY on Series 32 Models
All Partitions must be disarmed before starting the programming session.
If the system operates with LED Keypads only before starting the Pro-
gramming session, enrol an LCD Keypad at Address 8 (refer to Enrolling anLCD Keypad at address 8).
To start the Programming session:
1. From Standby status , enter the Installer code
(0025 at Default), then press EEEEE.
2. Select the required option from the PROGRAM-
MINGMenu.
Once PROGRAMMING has been accessed, the
Control panel will:
a) lock all Keypads, except for the one in use;
The locked Keypads will show thePROGRAMMING message, and all the indicators(I, aandG) will turn OFF.
Customizing the SystemInstaller Menu Options
Input
Code *-----
PROGRAMMING
Actions
Accessing the
Installer Menu
PROGRAMMING
PROGRAMMINGFROMTHELCD KEYPAD
-
7/25/2019 Kyo 4-8-32 Programming Manual
10/52
10 Multifunction Control Panel
Programming
eandE
NOTE: The examples in this section refer to the Kyo32 display (8 Partition
Control panel). Therefore, if you are using another type of Control panel, the
display messages/prompts may be slightly different.
Use the eeeeekey to step back at any point on the Installer Menu.
Use the EEEEEkey to confirm entered data.
Actions
This option provides a further 4 sub-options:
a) Test Siren this option will allow you to Test the Alarm Output relay.
b) Zones Status this option will allow you to Bypass/Unbypass zones.
c) View Logger this option will allow you to view the events in the Logger.
d) Clear Call Queue this option will allow you tointerrupt ongoing callsand stop the call queue.
You can find a full description of this options under Operating from a Key-
pad in the USER MANUAL.
b) clear the alarm memory;
c) force all the outputs (Alarm and Open Collector)to standby status;
d) stop the event evaluation;
e) if necessary interrupt the ongoing call, and put the Call queue on hold;f) activate the Plight (slow blink) on LED Keypads.
If you enter a Wrong Code the display will show an
error message, and go back to Standby status.
Exiting Programming
To exit Programming:
1. Presseeeee(as many times as necessary) to step back;
2. PressEEEEEwhen the Sure? prompt is shown.
If, at this point, you decide not to exit the menu, press eeeeeto continue.
When you exit the PROGRAMMING Menu the Control panel will:
a) restore all other Keypads to Standby status;
b) restore to Standby status or, if necessary, restart the call queue from the
interrupted call.
NOTE: Interrupted Teleservice calls will not be restarted.
c) turn off the Plight on the LED Keypads.
PROGRAMMING
Sure ?
WRONG CODE
Wrong Code
-
7/25/2019 Kyo 4-8-32 Programming Manual
11/52
11
Programming from the LCD Keypad
Zones
1. From the Installer Menu, using99999or 00000, selectthe Zonesoption, then press EEEEE.
2. Using99999or00000, select the Zone, then pressEEEEE.
3. Using99999or00000, select the Type, then pressEEEEE.
4. Using99999or00000, select the required Attribute.
PressOOOOOto Enable, oroooooto Disable the selectedAttribute, then press EEEEEto continue.
If you select the Wireless attribute (available
ONLY onKyo8W and Kyo32 Models), workcarefully through steps 5a, 5band 5c, otherwise,
go to step 6.
5a. Using the number keys, enter the ESN of the
Wireless device.
UseAAAAAorBBBBBto move along the row.
UseOOOOOoroooooto enter letters Athrough F.
NOTE - If you are changing a Wireless zone back to operating as
Hardwired, you must zero (000000) the ESN of the zone device .
PressEEEEEto go to the next step.
5b. Enable or Disable the Supervisoryattribute.
PressEEEEE to continue.
5c. Carry out thePlacement Test(create a Tamper
condition refer to the Wireless Device instruc-
tions sheet) to verify that the wireless device is within range of the VRX32-
433 or Vector/RX8.
One of the following values will be shown on the display:
Bad!
Fair!
Good!
DO NOT mount Wireless devices in placements
that give Bad!results.Placements can be considered
suitable after 3 consecutive Fair!or Good!results.
To repeat the Placement Test, presseeeeeand repeat steps 5band 5c.
G No wireless device should be mounted without first performing aPlacement Test.
PressEEEEEto go to step 6.
Zones
Zone 2
PROGRAMMING
Zones
Selecting the Zone
Zone 2
Path
Zone 2
Reserved OFF
Type
Attribute
Zone 2
000000
Zone 2
Superv. OFF
Wireless
Supervisory
Zone 2
Test
Placement Test
Zone 2
Wireless ON
Zone 2
Good!
-
7/25/2019 Kyo 4-8-32 Programming Manual
12/52
12 Multifunction Control Panel
Cycle (Vibration)
Zone 2
NO
Zone 2
Cycles 3
Alarm Cycles
Vibration or Roller
Blind Zone Balance
Zone 2
---- Part.
Assigning Partitions
Balance
Zone 2
Sensit. 2
Sensitivity (Valid only
Vibration
or Roller Blind)
6. Using 99999 or 00000, select the Balance type, thenpress EEEEE.
NOTE: If you assign the Vibration or Roller Blind attribute, youmust select one of the following Balance types:
BAL- Balance 1k5 (Balance using 1.5 Kohm resistor)
NC- Normally Closed
7. Using99999or00000, select the number of AlarmCy-cles: 0through 14.
If a continuous cycle is required, select RP (Re-
petitive), then press EEEEEto continue.
8. Using keys 11111 to 88888 (toggle keys), assign theZone to the Partitions:
= the Zone assigned-= the Zone is not assigned
PressEEEEEto continue.
9. Using 99999or 00000, select the required Sensitivity(1 through 20). This parameter is for Vibra-
tion and Roller Blind Zones only.
DO NOT program this parameter for other Zone Types.
Refer to Table 3 for other parameters relevant to Zones with the Roller
Blind attribute.
Example: for 3 PULSES and 4 MINUTES, you must set a value of 13.
10. For Zones with the Vibration attribute using
99999 or 00000, select the value of the Low ShockSensitivity or Cycles(0 through 7). PressEEEEEtoconfirm and go back to step 2.
Zone 2
Cycles 7
Zone 2
Cycles RP
-
7/25/2019 Kyo 4-8-32 Programming Manual
13/52
13
Programming from the LCD Keypad
Outputs
1. From the Installer Menu, using99999or00000, selectthe Outputs option, then press EEEEE.
2. Using 99999 or 00000, select the Output, then press
EEEEE.
3. Using 99999or 00000, select the requiredsignal type(Signals, ON Time, OFF Time, Part.), then
pressEEEEE. In accordance with the selected signaltype, work through the steps of the respective procedure.
4a. Using99999or00000, select the required signal: pressOOOOOto Enable, oroooooto Disable the signal on theOutput.
To program an Outputas Normally Open, selectN. O., then press ON.
To program an Outputas Normally Closed,
selectN. O., then press OFF.
Refer to the Outputs page section in the INSTALLATION MANUAL
for theSignalslist.
5a. PressEEEEEto confirm the setting, oreeeeeto quit and go back to step 3 (in bothcases).
4b. Enter the respective value. Accepted values: 0through 250 (useAAAAAorBBBBB to move along row).
5b. PressEEEEEto confirm the setting, oreeeeeto quit and go back to step 3 (in bothcases).
4c. Enter the respective value. Accepted values: 0
through 250 (useAAAAAorBBBBB to move along row).
5c. PressEEEEEto confirm the setting, oreeeeeto quit and go back to step 3 (in bothcases).
4d. Using keys 11111 to 88888 (toggle keys), enable theOutput on the respective Partitions:
= enabled
- = disabled
In the example, Output 2 is a Normally Closed Output enabled on Partitions
1and 8.
5d. PressEEEEEto confirm the setting, oreeeeeto quit and go back to step 3 (in bothcases).
Uscita 2
Signals
Signals
Output 2
N.O. ON
ON Time Output 2035 Seconds
OFF Time Output 2070 Seconds
Output 2------ Part.
Enabling Outputson Partitions
PROGRAMMING
Outputs
Outputs
Output 2
Output 2
Armed OFF
-
7/25/2019 Kyo 4-8-32 Programming Manual
14/52
14 Multifunction Control Panel
Partition 01
030 Seconds
Times
1. From the Installer menu, using99999or00000, select theTimes option, then press EEEEE.
2. Using 99999or 00000, select the required option, thenpress EEEEE.
3a. If you select:
Patrol
Listen.
Alarm
Inactiv.
Neglig.
Superv. (for Kyo32 and Kyo8W Models)
set the required Time, in accordance with the value
shown on the display, then press EEEEE to confirmthe setting, oreeeeeto quit and go back to step 2 (inboth cases).
The Accepted values can be found in Table 9 un-
der Programming from a LED Keypad.
NOTE:This value is in steps of 15 minutes(0 through 96: 10= 150 minutes).
ASupervisory Time of 8= 120 minutes is strongly advised.
4a. Using keys 11111 to 88888 (toggle keys), assign theInactiv.and Neglig.Times to the respective Par-
titions:
= assigned
-----= notassigned
PressEEEEEto confirm the setting, and go back to step 3a.
If you selected thePartit.option at step 2, work care-
fully through the following procedure.
3b. Using99999
or00000
, select the required Partition, thenpressEEEEEto confirm the setting, oreeeeeto quit andgo back to step 2.
4b. Using99999 or 00000, select the required option (forexample, Exit T.), then pressEEEEE.
5b. Enter the Time value, then press EEEEE(useAAAAAorBBBBBto move along the line).
The Entryand Exit Times are inSECONDS(0 - 250)
TheAuto-Arm Timeoutis inMINUTES (0 - 63)
The And Zonetime is inSECONDES(0 - 945). Insert a value 0 to 63
max: the input value must be multiplied for 15.
example 1: input 4x 15 = 60seconds
Times
Partit.
Partit.
Partition 01 Programming thePartition Times:
Exit T.
Entry T.
ArmT.Out
And Zone
Setting the Times:
Patrol
Listen.
AlarmInactiv.
Neglig.
Superv.
Partition 01
Exit T.
Alarm
03 Minuts
Listen.
050 Minuts
Superv.
00 x15 Minuts
Inactiv.
01 Hours
Inactiv.
---- Part.
Neglig.
---- Part.
Assigning
Inactiv./Neglig.
Times to Partitions
Neglig.
10 Days
Patrol
30 Minuts
PROGRAMMING
Times
Times
Patrol
-
7/25/2019 Kyo 4-8-32 Programming Manual
15/52
15
Programming from the LCD Keypad
example 2: input 63x 15 = 945seconds
6b. Repeat the procedure from step 4b, to program the other Time values for the
selected Partition.
PressEEEEEto confirm the setting, oreeeeeto quit and go back to step 3bto continue.
If you selected the 2PuZonesoption at step 2, work
carefully through the following procedure.
3c. Using 99999 or 00000, select the required Zone, thenpressEEEEEto confirm the setting, oreeeeeto quit andgo back to step 2.
4c. Enter the required value (0 through 250), then
pressEEEEE(useAAAAAorBBBBBto move along the line).The 2PuZonesTime is in SECONDS.
5c. PressEEEEEto confirm the setting, oreeeeeto quit and go back to step 3c(in bothcases).
2PuZones
Zone 01
2PuZone
030 Seconds
Times
2PuZones
Programming
Double pulse
-
7/25/2019 Kyo 4-8-32 Programming Manual
16/52
16 Multifunction Control Panel
PROGRAMMING
Inst.Cod
Installer Code
1. From the Installer Menu, using 99999or 00000, selectthe Inst. Cod option, then pressEEEEE.
2. Enter the New Installer Code(4 to 6 digits) then
pressEEEEEto confirm and go back to step 1.NOTE: The New Installer Code will not be valid until you exit the menu.
Inst.Cod
------
Keys
1. From the Installer Menu, using99999or00000, selectthe Keys option, then press EEEEE.
2. Using99999or00000, select either the Keys/CardsorWireless option (ONLY Series 32 and 8W
models provide the Wireless option), thenpressEEEEEand follow the relevant instructions.
Key/Cardoption (if selected at step 2.)
3. To enrol a New Key or Card, select New key
then press EEEEE(Go to step 4a).To Modify a Key or Card, select Modify
then press EEEEE(Go to step 4b).To Delete a New Key or Card, select Delete
then press EEEEE(Go to step 4c).4a. Using99999or00000select the Reader where the Key/
Card is to be enrolled, then pressEEEEE.
5a. Using99999 or 00000, select the Service, ClrCallQ,Andor Patrol attribute. Enable (OOOOO) or disable(ooooo) the attribute, as required, then press EEEEE.
For further details, refer to the Key/Card Page
section in the INSTALLATION MANUAL.
6a. Using keys 11111 to 88888 (toggle keys), assign theNew Key/Card to the Partitions.
= assigned
-= not assigned
7a. After assigning the Key/Card to the Partitions,
press EEEEE , the display will show the PRO-
GRAMMING prompt (see right).
8a. Insert the Key into the relevant ECLIPSE Reader (programmed at step 4a.), or
hold the Card near the sensitive field of the PROXI Reader (programmed at
step 4a.). Key/Card Enrollment will be confirmed by:
New Key/Card New keyReader 01
New key
Service ON
New key
ClrCallQ OFF
New key
PROGRAMMING
New key
---- Part.
PROGRAMMING
Keys
Keys
Key/Card
Keys
Wireless
New key
And OFF
Key/Card
New key
Key/Card
Modify
Key/Card
Delete
New key
Patrol OFF
-
7/25/2019 Kyo 4-8-32 Programming Manual
17/52
17
Programming from the LCD Keypad
Modify Key/Card
Delete Key/Card
a) a long beep
b) by an acceptance message which indicatesthe ID number (e.g. 009)
c) by fast blinking on all 3 Reader LEDs
9a. Usingeeeee
, go back to step 3.
If the system does not Enrol the Key/Card (due to fault or system limitations 128
keys) the Keypad will emit an audible error signal.
4b. Enter the Key/Card ID Number (e.g. 003) or, us-
ing AAAAA or BBBBB, select the required Key/Card IDNumber, then press EEEEE.
5b. Using99999 or 00000, select the Service, ClrCallQ,Andor Patrol attribut. Enable (OOOOO) or Disable(ooooo) the attribute, as required, then press EEEEE.
For further details, refer to the Key/Card Page section in the INSTALLA-
TION MANUAL.
6b. Using keys 11111 to 88888 (toggle keys), assign theKey/Card to the Partitions.
= assigned
-= not assigned
7b. PressEEEEEto confirm, and go back to step4b.
4c. Enter the Key/Card ID Number (e.g. 005) or, us-
ing AAAAA or BBBBB, select the required Key/Card IDNumber, then press EEEEE.
5c. When the Sure? prompt is shown, you can
either pressEEEEE, to confirm deletion and go backto step 4c, or press eeeee, to go back to step 4c,without deleting the Key/Card.
The keypad will emit an audible signal (long beep) to indicate that theKey/Card has been deleted.
Wirelessoption (if selected at step 2.)
3. Using99999or00000, select the Wireless key thenpress EEEEE.
4. Enter the ESN then pressEEEEE.
UseOOOOOoroooooto enter letters.
UseAAAAAorBBBBBto move along the row.5. Using99999or00000, select either User Code 23 or
24 for the Wireless key, then pressEEEEEto goback to step 3.
Modify
Service ON
Modify
---- Part.
Delete 005
Key/Card 5
Delete
Sure ?
Modify 003
Key/Card 3
Wireless
1 000000
Wireless
000000
Wireless
User Code 23
Wireless Key
New key 009
PROGRAMMING
-
7/25/2019 Kyo 4-8-32 Programming Manual
18/52
18 Multifunction Control Panel
Codes
1. From the Installer Menu, using99999or 00000, selectthe Codes option, then press EEEEE.
2. Using 99999 or 00000, select the Code Number (1through 24), then pressEEEEE.
3. Using99999or00000, select the CodeType (Inactive,Main User, User, Duress, Patrol or DTMF),
then press EEEEE.
4. Using OOOOO or ooooo , Enable or Disable theClrCallQ or Andoption, then press EEEEE.
5. Using99999or00000, select the Arming Mode (Part.,A Mode or B Mode), then pressEEEEE.
NOTE: If you selectPart. (Arm Enabled Partitions), go to step 6.
If you selectA orB Mode, go to step 6a.
6. Using keys 11111 to 88888 (toggle keys), assign theCode on the Partitions.
= assigned
-= notassigned
7. PressEEEEEto confirm and go back to step 5.
In the example, Code 5has been programmed as a UserCode, enabled to
ArmPartitions 1, 2and 4.
6a. Using keys11111to88888, program the Arming configu-ration for the Code, then pressEto confirm and goback to step 2.Each time you press the Partition
number key (1 to 8) the display will show a letter (D, A, S, I or N) which
represents an Arming option.
DDDDD = Disarm (the Control panel will monitor
onlythe 24h zones of the Partition)
AAAAA= Away Mode(the Control panel will monitor allthe zones of the Partition)
SSSSS= Stay Mode (the Control panelwill not monitor the Partition zones
with the Stay attribute)
IIIII= Instant(the Control panel will not monitorthe Partition zoneswith
the Stay attribute, and will remove the Partition entry delay)
NNNNN= No Change(the Control panel will not change the Partition status).
NOTE: If the User Code has not been assigned to any of the Partitions, this
programming field will be inactive (refer to step 6).
In the example, the A ModeArming Configuration for User Code 5is as
follows: Partition 1= Disarm, Partition 2= Away Mode,Partition 4=
Instant (Stay Mode 0 Delay),Partitions 3, 5, 6, 7, 8= No change.
Programming the
Arming configurations:
A and B Mode
PROGRAMMING
Codes
Codes
User Code 5
User Code 5
User
User Code 5
Part.
Part.
xx-x---- Part.
User Code 5
A Mode
A Mode
DANINNNN Part.
Arming options:
D, A, S, I, N
Code Type
User Code 5
ClrCallQ OFF
Code Options
-
7/25/2019 Kyo 4-8-32 Programming Manual
19/52
19
Programming from the LCD Keypad
PROGRAMMING
Readers
Readers
1. From the Installer Menu, using 99999or 00000, selectthe Readers option, then pressEEEEE.
2. Using99999or00000select the Reader (1 through 16),then press EEEEE.
3. Using99999or 00000Enable (ON) or Disable (OFF)the Reader, then press EEEEE.
4. Using99999or00000, select Arming Mode (Part.,AMode or B Mode), then pressEEEEE.
NOTE: If you selectPart. (Arm Enabled Partitions), go to step 5.
If you selectA orB Mode, go to step 5a.
5. Using keys 11111 to 88888 (toggle keys), assign theReader to the Partitions.
= assigned
-= not assigned
6. PressEEEEEto confirm and go back to step 4.
In the example,Reader05has been programmed to Arm the system inPart.
Mode (Arm Enabled Partitions), and assigned to Partitions3and 4
5a. Using keys11111to88888, setup the Arming configu-ration, then press Eto confirm and go back tostep 2.
Each time you press the Partition number key, the
display will scroll a series of letters
(D, A, S, I or N), with the following meaning:
D = Disarm (the Control panel will monitoronly the 24h zones of thePartition)
A = Away Mode (the Control panel will monitor all the zones of the
Partition)S= Stay Mode (the Control panelwill not monitor the Partition zoneswith the Stay attribute)
I= Instant(the Control panel will not monitorthe Partition zoneswith theStay attribute, and will eliminate the Partition entry delay)
N= No Change(the Control panel will not change the Partition status).
NOTE: If the Reader has not been assigned to any of the Partitions, this
programming field will be inactive (refer to step 5).
In the example, theB ModeArming configuration forReader 05 is as follows:
Partitions 1, 2, 5, 6, 7 and8 = Not Enabled,Partition 3= Away Mode,
Partition 4= Disarm.
Readers
Reader 05
Reader 05
ON
Reader 05
Part.
Part.
------ Part.
Reader 05
B Mode
B Mode
--AD---- Part.
Selecting the Reader
Enabling the Reader
Arming Mode:
Part., A or B Mode
Assigning the Readerto Partitions
Arming option:
D, A, S, I, N
Programming theArming configurations:
A or B Mode
-
7/25/2019 Kyo 4-8-32 Programming Manual
20/52
20 Multifunction Control Panel
PROGRAMMING
Keypads
Keypads
If you are using a Control panel from the Kyo32 and Kyo8W Series, the
application will present two sub-menus: Program and Language. In all
other models you will access the Keypad Programming phase directly.
1. From the Installer Menu, using 99999or 00000, selectthe Keypadsoption, then press EEEEE.
2. Using99999or00000, select the required option (Pro-gram or Language), then pressEEEEEand workcarefully through the relevant instructions.
Program option
3a. Using99999or 00000, select the Keypad (1 to 8), thenpress EEEEE.
4a. Using99999or00000, select the Keypad Type(selectNone for NO KEYPAD), then press EEEEE.
5a. Using keys 11111 to 88888 (toggle keys), assign theKeypad to the Partitions.
= assigned
-= not assigned
6a. PressEEEEE
to confirm and go back to step 3a.
In the example,Keypad 03(LCDKeypad) is assigned to Partitions1and 5.
Language option (Kyo32 and Kyo8W Series only)
3b. Press the key which corresponds to the required
language (in brackets e.g. ).
4b. PressEEEEEoreeeeeto confirm. The selected languagewill be operative immediately. The system will go back to step 2.
Keypads
Program
Keypads
Language
Program
Keypad 03
Keypad 03
LCD Keyp.
Keypad 03
------
1: ITA
3: ESP 4:FRA
Selecting the Language
Selecting the Keypad
-
7/25/2019 Kyo 4-8-32 Programming Manual
21/52
21
Programming from the LCD Keypad
PROGRAMMING
Date/T.
Date/Time
1. From the Installer Menu, using 99999or00000, selectthe Date/T. option, thenpressEEEEE.
2. UsingAAAAA
orBBBBB
, select the Day, Month, Year,Hour or Minutes field.
Use99999or00000change the values as required.
PressEEEEEto confirm and go to next step.
3. Using 11111 , 22222 or 33333 , select the Date format(D=Day, M=Month, Y=Year). The selected for-
mat will be shown in brackets ().
4. Press EEEEEto confirm and go back to step 1.
GGGGG Remember to put the Clock forward or back an hour for the Summer Timechangeover.
Date/Time
01/11/2002 12:55
PROGRAMMING
Timers
Timers
1. From the Installer Menu, using 99999or00000, select
the Timersoption, then pressEEEEE
.2. Using99999or00000, select the Partition, then pressEEEEE.
3. Using99999or00000, select the Day. UsingOOOOOorooooo,Enable or Disable the Partition (All Days areOFF
at Default), then press EEEEE.
4. UsingAAAAAorBBBBB, select the Hour or Minutes. Us-ing99999or 00000, select the value (max 23:59), then
pressEEEEEto confirm and go to step 2.
In the example, Partition 2will Arm every Wednesdayat 10:35.
NOTE: The En/Dis. Auto-Arm must be enabled, otherwise, the programmed
Auto-Arming schedule will be ignored.
Timers
Partition 02
Partition 2
WED ON
Partition 2
WED 10:35
1 2 3
MDY YMD
-
7/25/2019 Kyo 4-8-32 Programming Manual
22/52
22 Multifunction Control Panel
Number 3
_____ Customer
Telephone
1. From the Installer Menu, using 99999or 00000, selectthe Teleph.option, then press EEEEE.
2. Using99999
or00000
, select the TelephoneNumberID number (1 to 8), then press EEEEE.
3. Using 99999or 00000, select the Telephone NumberType, then press EEEEE.
4. Using keys11111 to88888(toggle keys), assign the Tel-ephone Number to the Partitions, then pressEEEEE.
= assigned
-= not assigned
NOTE - The Telephone Numbers must be assigned to the Partitions, other-
wise, the User will be unable to program Voice Telephone Numbers (refer to
the USER MANUAL).
5. Enter the Telephone number.
UseAAAAAorBBBBB, to move along the row.
Use OOOOO and ooooo for the following punctuation marks and pauses (to beentered in the space indicated by the cursor):
a) , use the comma to insert 2 second dialling pauses;b) _ use the dash to clear telephone number digits;
c) *and #.
6. Once the Telephone number has been completed, pressEEEEEto confirm andgo back to step 2.
If, at step 3,you selected a Telephone Number Type which operates with a
protocol (reporting format), work carefully through the following steps.
7. Enter theCustomer Code (minimum 4 digits for
all reporting formats except CESA, that requires
5 digits), then pressEEEEE.
UseAAAAAorBBBBBto move along the row.
UseOOOOOoroooooto enter letters A through F.
8. Using99999or 00000, select either the Listen.or 2-way option then, using OOOOO or ooooo , Enable orDisable these options, as required.
9. PressEEEEEto confirm and go back to step 1.
Teleph.
Number 3
PROGRAMMING
Teleph.
Number 3
Voice
Number 3
0731667890______
Number 3
Part.
Type:
Contact ID
CESA
10-140014 bps
20 bps
40 bps
10-1600
Number 3
Listen. OFF
Number 3
2-way ON
-
7/25/2019 Kyo 4-8-32 Programming Manual
23/52
23
Programming from the LCD Keypad
Teleservice
1. From the Installer Menu, using 99999or00000, selectthe Teleser. option, then press EEEEE.
2. Using 99999 or 00000, select the Rings option, thenpress EEEEE.
3. Using 99999 or 00000, select the number of rings (0through 19), then pressEEEEE.
4. Using99999or 00000, select the Numberoption, thenpress EEEEE.
5. Using99999or00000, select theTelephone number(1through 8) for Teleservice.
6. PressEEEEEto confirm and go back to step 4.
In the example, Telephone number 7 has been assigned to the Teleservice call,
which will be answered after 4rings.
PROGRAMMING
Teleser.
Teleser.
Rings
Rings
4
Teleser.
Number
Number
Number 7
Test Ev.
1. From the Installer Menu, using99999or00000, selectthe Test Ev., then pressEEEEE.
2. Using99999or00000, select the Day, Month, Year andTime values. UseAAAAAorBBBBBto move along the row.
3. Once the programming field has been completed, pressEEEEE.
4. Enter the Interval(in hours) between Test events.
UseAAAAAorBBBBBto move along the row.
5. PressEEEEEto confirm and go back to step 1.
In the example, the firstTestwill be carried out on the 25/09/2002at 10:30.
Successive Tests will be carried out every 30 days (Interval = 720 hours).
To disable the Test event, enter 0000.
PROGRAMMING
Test Ev.
Interval
0720
Date/Time
25/09/2002 10:30
-
7/25/2019 Kyo 4-8-32 Programming Manual
24/52
24 Multifunction Control Panel
PROGRAMMING
Events
Events
1. From the Installer Menu, using99999or 00000, selectthe Events option, then pressEEEEE.
2. UsingAAAAAor BBBBBselect the Event, then pressEEEEE.This programming field will allow you to enter the
Event number directly. An asterisk (*) next to the
Event number (see right) means the Event has been programmed as a Prior-
ity Event(refer to Events Page in the INSTALLATION MANUAL).
For the complete list ofEvents, refer to the Events Page section in the
INSTALLATION MANUAL.
3. Enter the Event Code, then pressEEEEE.
UseOOOOOoroooooto enter letters A through F.4. Using99999or00000, select the ID number (1 to 8) of
the Voice Message which will be associated with
the Event, then press EEEEE.
5. Using keys 11111 to 88888 (toggle keys), assign theTelephone number to the Events.
= assigned
-= not assigned
6. PressEEEEEto confirm and go back to step 2., the display will show the nextEvent on the list.
In the example, Event Code21has been assigned toEvent 000(Alarm Partition
01). Message number4 will be sent to Telephone numbers 3, 4and 8when the
Event occurs.
Events *000
Partit.Alarm 001
Code
21
Mess.
4
Tel.Numb
-----
Priority Event
-
7/25/2019 Kyo 4-8-32 Programming Manual
25/52
25
Programming from the LCD Keypad
Autores.
------ Part.
PROGRAMMING
Options
Options
1. From the Installer menu, using 99999or 00000, selectOptions, then press EEEEE.
2. Using 99999 or 00000 , select the required Optionnumber, using OOOOO or ooooo, Enable or Disable theOptionas required.
For the complete list of Options, refer tothe Options Page in theINSTAL-
LATION MANUAL.
3. When all the Options have been programmed, press EEEEE.
4. Using keys11111to88888(toggle keys), Enable/Dis-able theAuto Reset Memoryoption on the Par-
titions.
= Enabled,
-= Disabled
5. PressEEEEEto confirm and go back to step 1.
In the example, theAuto-Reset Memory option is enabled on Partitions 1and 8.
Once the Wireless Receiver (option number 3) has been enabled, you must
exit then re-access the Installer Menu. This procedure will allow the Control
panel to activate and setup the Wireless Receiver properly. If you do not followthis procedure, the Control panel will not allow you to program the Wireless
Zones, Wireless Keys and other Wireless Receiver options.
Options
0 OFF
Enabling VRX32-433
and Vector/RX8
Receiver
-
7/25/2019 Kyo 4-8-32 Programming Manual
26/52
26 Multifunction Control Panel
Strings
This option will allow you to customize the descriptions of the system periph-
erals, etc.
1. From the Installer Menu, select theStrings op-
tion, then press EEEEE.
2. Using99999or00000, select the relevantString (refertoTable 4), then press EEEEE.
3. Enter the label (maximum 16 letters).
Use99999or00000to enter the letters.
UseAAAAAorBBBBBto move along the row.
In the example, the Partition 02 String (label) has been programmed as
Main Door.
PROGRAMMING
Strings
Strings
Partition 02
Partition 02
Main Door
-
7/25/2019 Kyo 4-8-32 Programming Manual
27/52
27
Programming from the LCD Keypad
Default
GGGGG- The default option will allow you to reset the Control panel to FactoryDefault, and delete the Events List.
1. From the Installer Menu, select the Defaultop-
tion, then press EEEEE.
2. Using99999or00000, select the data to be deleted:
All Restores the Control panel to Factory
Default, and deletes the Events Program List.
NOTE - TheStringswill not be restored to default (refer to Strings on the
previous page).
Ev.Cod. Restores all the Event Codes toContactID. If a ContactID Telephone number ex-
ists, all Events will be assigned to it.
Ev.Cod=0 Restores all the Event Codes,
therefore, the Events will be unable to generate
Telemonitoring calls.
Receiver Restores all the Wireless Receiver
values to Factory Default. This operation will de-
lete all the ESNs and Wireless keys(forSeries 8W
and 32Models ONLY).
3. PressEEEEE, to restore Factory Default, oreeeeeto quitwithout changing the current data.
GGGGGRestoral of the Factory Default settings will lock the Control panel for
several seconds.
After All, Ev.Cod.or Ev.Cod=0Factory Default restoral, the Control panel
will exit the programming phase automatically.
After ReceiverFactory Default restoral, the Control panel will go back tostep1.
PROGRAMMING
Default
Default
All
Default
Receiver
Default
Ev.Cod.
Default
Ev.Cod=0
Default
Sure ?
-
7/25/2019 Kyo 4-8-32 Programming Manual
28/52
28 Multifunction Control Panel
Input Expanders
This option is available on Series 32 Models, and will allow you to program the
Input Expanders.
1. From the Installer Menu, using 99999or 00000, selectEsp. IN then pressEEEEE.
2. Using 99999 or 00000, select the required Input Ex-pander then press EEEEE.
Up to 4 Input Expanders can be enabled (6 zones per Expander).
3. Using99999or00000, enable or disable the Input Ex-pander as required.
4. PressEEEEEto go back to step 2to program another Input Expander.
PROGRAMMING
Exp. IN
Exp. IN
Expander In 1
Expander In 1
OFF
Output Expanders
This option is available on Series 32 Models, and will allow you to program the
Output Expanders.
1. From the Installer Menu, using 99999or 00000, select
Esp. OUT then pressEEEEE
.2. Using 99999 or 00000, select the required Output Ex-
pander then press EEEEE.
1 or 2 Output Expanders can be enabled (6 outputs per Expander).
3. Using99999or00000, enable or disable the Output Ex-pander as required.
4. PressEEEEEto go back to step 2to program another Output Expander.
PROGRAMMING
Exp. OUT
Exp. OUT
Expander Out 1
Expander Out 1
OFF
-
7/25/2019 Kyo 4-8-32 Programming Manual
29/52
29
Programming from the LED Keypad
Programming from the LED Keypad
Only the following models from the Kyo range can be programmed via LED
Keypad:
KYO 4M
KYO 4P
KYO 8M
KYO 8P
All Partitions must be Disarmed before starting the programming session.
1. From Standby status, enter the Installer code (0025 at Default), then
press EEEEE.
If you enter a wrong code, the Control panel will emit an audible error signal.
When you access the Programming session, the Control panel will:
a) activate the Pindicator (slow blink) on LED Keypads;
b) turn off all the indicators (I,aandG);
c) clear the alarm memory;
d) force all the outputs (Alarm and Open Collector) to standby status;
e) stop the event evaluation;
f) if necessary interrupt ongoing calls, and put the Call queue on hold;
g)lock all other Keypads, except for the one in use.
Exiting Programming
Presseeeeeto step back (the Control panel will take one step back each
timeeeeeeis pressed).When you exit the Programming session, the Control panel will:
a) restore all other Keypads to Standby status;
b) restore to Standby status or, if necessary, restart the call queue from the
interrupted call.
NOTE: Interrupted Teleservice calls will not be restarted.
c) turn off the Plight on the LED Keypads.
Accessing Programming
Accessing the
Programming session
-
7/25/2019 Kyo 4-8-32 Programming Manual
30/52
30 Multifunction Control Panel
Programming
Enrolling Keypads
Enabling Keypads
on Partitions
The ON/OFF status of the backlit keys on the NC2TAST, and the LEDs (1 to 8) on
the ICON/KP Keypads determines respectively the enabled/disabled status of the
options.
Keypads
1. To enrol one or more Keypads, ente the respective parameter number from
(1through 8), then pressE.
2. Using key1,2or3, set the type of Keypad (refer to Tab. 5.).
3. PressEto confirm, oreto abort the setting.
1. To enable a Keypad on the Partitions, enter a Parameter Number from 9-16
(refer to Tab. 5 for details), then pressE.
2. Using keys1to4(which correspond respectively to Partitions 1 to 4),enable/disable the Keypad on the Partitions (refer to Tab. 5 for details).
3. PressEto confirm, oreto abort the setting.
NOTE:Wrong entries can be deleted by pressinge. This operationmay at times exit theProgrammingmenu completely, in such cases, it will be
necessary to re-enter the Installer code.
-
7/25/2019 Kyo 4-8-32 Programming Manual
31/52
31
Programming from the LED Keypad
Readers
1. To enrol Readers 1 to 8: enter 18, then pressE.
NOTE:At this point, keys1to8correspond to Readers 1 to 8.
To enrol Readers 9to 16: enter 17, then pressE.
NOTE: At this point, keys1 to8 correspond to Readers 9 to 16(i.e. key1corresponds to Reader 9, key2 to Reader 10, etc.).
2. Press the respective keys to enrol Readers on the system (refer to Tab. 6 for
details).
3. PressEto confirm, oreto abort the setting.
1. To enable Readers on Partitions 1 to 4, enter a Parameter Number from
19 154(refer to Tab. 6 for details), then pressE.
2. Using keys1 to4 (respectively Partitions 1 to 4), enable/disable theReader on the Partitions(refer to Tab. 6 for details).
3. PressEto confirm, oreto abort the setting.
1. To set up theA ModeArming configuration, enter a Parameter Number
from20 155(refer to Tab. 6 for details), then press E.
2. Using keys1to4 (respectively Partitions 1 to 4), set up the A Mode
Arming configuration.
Enrolling Readers
A Mode Arming
Enabling Readers
on Partitions
-
7/25/2019 Kyo 4-8-32 Programming Manual
32/52
32 Multifunction Control Panel
Setting up the Zones
1. To set up the Type and Balance, enter a Parameter Number from163 191
(refer to Tab. 7a for details), then pressE.
NOTE:At this point, keys1to5will allow you to program the Zone Type andBalance (refer to Meaning of LED/Key status in Tab. 7a).
2. Using keys1to3, select the Zone Type.
3. Using keys4 and/or 5, select the Balance Type.
4. PressEto confirm, oreto abort the setting.
1. To assign the Zone Attributes, enter a Parameter Number from 164 192
(refer to Tab. 7a for details), then pressE.
NOTE:At this point, keys1to8correspond to Zones 1 to 8.
2. Using the respective key, assign the Zone Attribute (refer to Tab. 7a for
details).
IMPORTANT - Ensure that you DO NOT press keys7and8contempo-rarily.
3. PressEto confirm, oreto abort the setting.
Setting up the
Type and Balance
Zone Attributes
NOTE:The ON, OFF, Slow or Fast Blinking status of each key determines
the status the respective Partition will adopt duringA Mode(refer to Mean-
ing of LED/Key status in Tab. 6).
3. PressEto confirm, oreto abort the setting.
NOTE: The Reader will not accept Z Mode (Stay with 0 Delay).
1. To set up theB ModeArming configuration, enter a Parameter Number
from24 159(refer to Tab. 6 for details), then press E.
2. Using keys1 to4 (respectively Partitions 1 to 4), set up the B ModeArming configuration.
NOTE:The ON, OFF, Slow or Fast Blinking status of each key determines
the status the respective Partition will adopt duringB Mode(refer to Mean-ing of LED/Key status in Tab. 6).
3. PressEto confirm, oreto abort the setting.
NOTE: The Reader will not accept Z Mode (Stay with 0 Delay).
B Mode Arming
-
7/25/2019 Kyo 4-8-32 Programming Manual
33/52
33
Programming from the LED Keypad
Assigning Zones to
Partitions
1. Enter a Parameter Number from 165 193(refer to Tab. 7a for details), then
pressE.
NOTE:At this point, keys1to4correspond to Partitions 1 to 4.
2. Using keys1to4, assign the Zone to the Partitions (refer to Tab. 7a fordetails).
-
7/25/2019 Kyo 4-8-32 Programming Manual
34/52
34 Multifunction Control Panel
Cycles
Vibration and
Rollerblind
Attributes
3. PressEto confirm, oreto abort the setting.
1. Enter a Parameter Number from166 194(refer to Tab. 7a for details), then
pressE.
2. Enter the required number of Cycles (refer to Tab. 7a).
Accepted entries: 0 through 15 (0 = No cycles; 15 = Repetitive). If you
enter a wrong value the Keypad will emit an audible error signal then allow
you to retry.
3. PressEto confirm, oreto abort the setting.
1. Enter a Parameter Number from 307 312(refer to Tab. 7a for details), then
pressE.
NOTE- ONLY the first 6 Zones can be Vibration or Rollerblind Zones.
2a. Vibration Zones Enter the required value (refer to Tab. 7b).
Accepted entries: 0 through 243. If you enter a wrong value (e.g. more than
243) the Keypad will emit an audible error signal then allow you to retry.
2b. Rollerblind Zones Enter the required value (refer to Tab. 7c).
Accepted entries: 0 through 19. If you enter a wrong value (e.g. more than
19) the Keypad will emit an audible error signal then allow you to retry.
3. PressEto confirm, oreto abort the setting.
-
7/25/2019 Kyo 4-8-32 Programming Manual
35/52
35
Programming from the LED Keypad
Setting up the Outputs
1. Enter a Parameter Number from191 210(refer to Tab. 8 for details), then
pressE.
2. Using keys1to8, enable the required Activation Signal (refer to Tab.8 for details).
3. PressEto confirm, oreto abort the setting.
1. Enter a Parameter Number from211 215(refer to Tab. 8 for details), then
pressE.
2. Using keys1to4, enable the Output on the Partitions (refer to Tab. 8for details).
3. PressEto confirm, oreto abort the setting.
Assigning Partitions
-
7/25/2019 Kyo 4-8-32 Programming Manual
36/52
36 Multifunction Control Panel
-
7/25/2019 Kyo 4-8-32 Programming Manual
37/52
37
Programming from the LED Keypad
Setting up Times, Inactivity and Negligence
1. Enter the relevant Programming Address (refer to Tab. 9 Programming
Addresses 220 264), then pressE.
2a. Enter the required value (maximum 3 digits). The accepted values can be
found in Tab. 9.
ATTENTION- The Control panel DOES NOT verify the validity of data
entries.
2b. Using keys1through4, enable/disable the Inactivity and/or Negligenceoptions on the Partitions.
3. PressEto confirm, oreto abort the setting.
Times
Enabling Inactivity
and/or Negligence
-
7/25/2019 Kyo 4-8-32 Programming Manual
38/52
38 Multifunction Control Panel
Telephone
1. Enter a Parameter Number from703 892(refer to Tab. 10a for details),
then pressE.
2. Enter the Telephone Number (maximum 20 digits).
3. PressEto confirm, oreto delete the entry.
Setting up the
Phonebook (up to 8
Telephone Numbers)
-
7/25/2019 Kyo 4-8-32 Programming Manual
39/52
39
Programming from the LED Keypad
Setting up theDialling Type
1. Enter a Parameter Number from723 912(refer to Tab. 10a for details),
then pressE.
2. Enter the Customer Code (5 digits 0 through 9).
3. PressEto confirm, oreto delete the entry.
1. Enter a Parameter Number from 728 917(refer to Tab. 10a for details),
then pressE.
2. Using keys1to7, define the Reporting Format, Telephone Number andCentral Station Types (refer to Tab. 10a. for details). Key 5 isuninfluential.
3. PressEto confirm, oreto abort the setting.
1. Enter a Parameter Number from 729 918(refer to Tab. 10a for details),
then pressE.
2. Using keys1to4, enable/disable the Telephone number on the Parti-tion (refer to Tab 10a for details).
3. PressEto confirm, oreto abort the setting.
This option is relevant to Voice Telephone Numbers only.
1. Enter Parameter Number 283, then pressE.
2. Using key6, enable/disable the Disallow Tone Check option, then us-ing key7select the relevant Dialling mode (refer to Tab. 10b for details).
3. PressEto confirm, oreto abort the setting.
Central Station
Customer Code
Assigning the
Telephone Numbers
to Partitions
Type and
Teleservice
-
7/25/2019 Kyo 4-8-32 Programming Manual
40/52
40 Multifunction Control Panel
Setting up Teleservice and Test Event
1. Enter Parameter Number 283, then press E.
2. Using keys3and/or5, enable/disable the Callback and DoubleCall options (refer to Tab. 11 for details).
3. PressEto confirm, oreto abort the setting.
1. Enter Parameter Number 281, then pressE.
2. Enter the required number of rings (accepted entries: 0 through 19).
3. PressEto confirm, oreto abort the setting.
1. Enter Parameter Number 282, then pressE.
2. Enter the Telephone number ID number (refer to Tab. 11 for details).
3. PressEto confirm, oreto abort the setting.
1. Enter Parameter Number 286,then pressE.
2. Using key8, enable/disable the Test Call (refer to Tab. 11 for details).
3. PressEto confirm, oreto abort the setting.
1. Enter Parameter Number 300,then pressE.
2. Enter the Date and time of the Test Event in DDMMYYHHMM format
(10 digits), for example, to set 3rd May 2004 enter030504.
3. PressEto confirm, oreto abort the setting.
1. Enter Parameter Number 304,then pressE.
2. Enter the number of hours between each Test Event (accepted entries: 1
through 9999). To disable the Interval, enter 0 (zero).
3. PressEto confirm, oreto abort the setting.
Callback and
Double Call
Number of Rings
Installer Telephone
Number
Test Call
First Test Event
Interval
-
7/25/2019 Kyo 4-8-32 Programming Manual
41/52
41
Programming from the LED Keypad
Events
1. Enter a Parameter Number from 919 1720 (refer to Tab. 12), then press
E.
2. Enter the Event Code, then pressE.
IMPORTANT- The Event Codes are Decimal Codes (accepted entries:
0 through 255). The DECIMAL HEXADECIMAL Conversion Table can
be found at the end of this Manual.
1. Enter a Parameter Number from920 1721(refer to Tab. 12 for details),
then press E.
2. Using keys0to8, assign the Telephone Number to the Event.
1. Enter a Parameter Number from 921 1722(refer to Tab. 12 for details),
then press E.
2. Using keys0to7, assign the respective Voice Message (refer to Tab. 12for details), then pressE.
Example:Press0to assign Message 01, 1to assign Message 02, etc.
Setting up the
Events
Assigning
Telephone Numbers
Assigning Messages
to Events
-
7/25/2019 Kyo 4-8-32 Programming Manual
42/52
42 Multifunction Control Panel
Setting up the Scheduler
1. To set up the Scheduler, enter a Parameter Number from2619 2664 (refer
to Tab. 13 for details), then press E.
2. Using keys1to7, link the respective days of the week with the Parti-tion (refer to Tab. 13 for details), then pressE.
3. PressEto confirm, oreto abort the setting.
1. To set the Times (HOURS and MINUTES), enter a Parameter Number
from 2620 2665 (refer to Tab. 13 for details), then pressE.
2. Enter the required Times (HOURS and MINUTES), then pressEtoconfirm the setting.
Linking Days
with Partitions
Times:
Hours and Minutes
-
7/25/2019 Kyo 4-8-32 Programming Manual
43/52
43
Programming from the LED Keypad
Enabling Options
Options
1. Enter a Parameter Number from283 290 (refer to Tab. 14 for details),
then pressE.
2. Using keys1to8, enable the Options as required (refer to Tab. 14 fordetails).
NOTE: A full description of the Options can be found on the back page of
the INSTALLATION MANUAL.
3. PressEto confirm, oreto abort the setting.
1. To set Auto-Reset Memory, enter 291then pressE.Auto-Reset Memory
-
7/25/2019 Kyo 4-8-32 Programming Manual
44/52
44 Multifunction Control Panel
2. Using keys1to4(which correspond respectively to Partitions 1 to 4),enable/disable the Auto-Reset Memory option (refer to Tab. 14 for de-
tails).
3. PressEto confirm, oreto abort the setting.
-
7/25/2019 Kyo 4-8-32 Programming Manual
45/52
45
Programming from the LED Keypad
Programming the
Installer Code
Code Type
Codes
1. Enter a Parameter Number from463 693 (refer to Tab. 15 for details),
then pressE.
2. Using keys1to3, define the Code Type (refer to Tab. 15 for de-tails).
3. PressEto confirm, oreto abort the setting.
1. Enter a Parameter Number from 464 694 (refer to Tab. 15 for details),
then pressE.
2. Using keys1to4, enable/disable the Code on the Partitions (refer toTab. 15 for details).
3. PressEto confirm, oreto abort the setting.
1. Enter a Parameter Number from 465 695 (refer to Tab. 15 for details),
then pressE.
2. Using keys 1 to 4 (Partitions 1 to 4 respectively ) set up the AArming Mode for the Code (refer to Tab. 15 for details).
NOTE: The Reader will not accept Z Mode (Stay with 0 Delay).
3. PressEto confirm, oreto abort the setting.
1. Enter a Parameter Number from 469 699 (refer to Tab. 15 for details),
then pressE.
2. Using keys 1 to 4 (Partitions 1 to 4 respectively ) set up the BArming Mode for the Code (refer to Tab. 15 for details).
NOTE: The Reader will not accept Z Mode (Stay with 0 Delay).
3. PressEto confirm, oreto abort the setting.
1. Enter Parameter Number 457, then pressE.
2. Enter the New Installer Code, then pressE.
Options for Type A
Arming Mode
Options for Type B
Arming Mode
Enabled Partitions
-
7/25/2019 Kyo 4-8-32 Programming Manual
46/52
46 Multifunction Control Panel
Changing
Keys/Cards
Programming Keys and Cards
1. To program a new Key/Card, enter Parameter Number 5000, then press
E. TheXindicator will turn ON.
2. Enter the ID Number of the Reader you intend to use (accepted entries: 1
through 16), then pressE. The Sindicator will turn ON.
ATTENTION- The Reader must be enrolled on the system, and must be in
standby status before starting the Key/Card programming session.
3. Using1(SERVICE),2(RESET CALL QUEUE),3(AND) and/or4
(PATROL) set up the Key/Card Options, then pressEto confirm andcontinue (Tindicator ON), or presseto abort the setting and step back.
4. Using keys1to4, enable/disable the Key/Card on the respective Parti-
tion (refer to Tab. 16 for details), then pressEto continue, oretostep back.
5. Hold the Key/Card near the sensitive field of the Reader, or insert the key
into the Reader. Successful enrolling will be indicated by:
a)a long beep;
b)theVindicator (ON);
c) the Binary Code of the respective Key/Card ID Number on the Keypad.
If enrolling fails, the Reader will emit an audible error signal, and all the
backlit keys will turn OFF.
NOTE: TheDECIMAL BINARYConversion Table can be found at the
end of this Manual.
Repeat the procedure for each of the system Key/Cards.
6. Presseto step back.
1. To change a Key/Card, enter a Parameter Number from 5001 5128(refer
to Tab. 16 for details), then pressE.
2. Using1(SERVICE),2(RESET CALL QUEUE),3(AND) and/or4(PATROL) change the Key/Card options. If the Key/Card has been
properly enrolled, key7(LED 3) will light. To unenrol the Key/Card,press8. The Key/Card will be unenrolled when the programming sessionends.
3. PressEto go to the next step.
4. Using keys1to4, enable/disable the Key/Card on the respective Parti-
tion (refer to Tab. 16 for details), then pressEto continue, oretostep back.
Programming
New Keys/Cards
-
7/25/2019 Kyo 4-8-32 Programming Manual
47/52
47
Programming from the LED Keypad
-
7/25/2019 Kyo 4-8-32 Programming Manual
48/52
48 Multifunction Control Panel
Extra Parameters
ATTENTION- TheExtra Parametersare reserved for Factory program-
ming purposes.
1. To program the Extra Parameters, enter a Parameter number from 265280, then pressE.
2. Enter the respective Parameter Number, then pressE.
Customized Protocol Parameters
ATTENTION- The Customized Protocol Parametersare reserved for Fac-tory programming purposes.
1. To program the Customized Protocol Parameters, enter a Parameter number
from 2680 2691, then pressE.
2. Enter the respective Parameter Number, then press E.
-
7/25/2019 Kyo 4-8-32 Programming Manual
49/52
49
Programming from the LED Keypad
-
7/25/2019 Kyo 4-8-32 Programming Manual
50/52
50 Multifunction Control Panel
-
7/25/2019 Kyo 4-8-32 Programming Manual
51/52
51
-
7/25/2019 Kyo 4-8-32 Programming Manual
52/52