www.krups.com

0304

25

0304

25

d

e

d

j

kk1

k2k3

b

a

o

p

q

n

g

f

h

i

l

m

0304

25

1 2 3

4 5 6

7 8 9

1110

0304

25

12 13

14 15 16

17 18

21 20

19

0304

25

22

25

28 29

26 27

23 24

0304

25

31 3230

33 34 35A

B

C

36 37 8838 38

7

USA 8Instructions for UseWarrantyGuarantee of Performance

Novo 3000 FNC2Novo 3000 Premium FNC3

Mode d’emploiGarantieGarantie de rendement

Español 30

Instrucciones de usoGarantíaGarantía de rendimiento

Français 19

Español

8

USA

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions shouldalways be followed to reduce the risk of fire, electric shock and/orinjury to persons, including the following:•Read all instructions.•Do not touch hot surfaces. Use handles or knobs.•To protect against fire, electric shock and injury to persons, do notimmerse cord, plugs, or appliance in water or other liquid.

•Close supervision is necessary when any appliance is used by ornear children.

•Unplug from outlet when not in use and before cleaning. Allow tocool before putting on or taking off parts, and before cleaning theappliance.

•Do not operate any appliance with a damaged cord or plug orafter the appliance malfunctions, or has been damaged in anymanner. Return appliance to your nearest authorized KRUPSService Center for examination, repair or adjustment (seeGuarantee of Performance).

•The use of accessory attachments not recommended by KRUPSmay result in fire, electric shock or injury to persons.

•Do not use outdoors.•Do not let cord hang over edge of table or counter, or touch hotsurfaces.

•Do not place on or near a hot gas or electric burner, or in a heatedoven.

•To disconnect, turn switch to “OFF”, then remove plug from walloutlet.

•Do not use appliance for other than intended use.•Use extreme caution when dispensing hot steam.

SAVE THESE INSTRUCTIONS

9

CAUTION

•This appliance is for household use only. Any servicing other thanroutine cleaning and user maintenance should be performed byauthorized KRUPS service personnel only (see Guarantee ofPerformance).

•Do not immerse base in water.•To reduce the risk of fire or electric shock, do not remove the baseof the machine. There are no user serviceable parts inside. Repairsshould be performed by authorized KRUPS service personnel only.

SPECIAL CORD SET INSTRUCTIONS

Regarding your Cord Set:A. A short power-supply cord is to be provided to reduce risks

resulting from becoming entangled in or tripping over a longercord.

B. Longer extension cords are available and may be used if care isexercised in their use.

C. If a long extension cord is used, (1) the marked electrical ratingof the extension cord should be at least as great as the electricalrating of the appliance, (2) the longer cord should be arrangedso that it will not drape over the counter top or table top whereit can be pulled on by children or tripped over.

D. This appliance has a polarized plug (one blade is wider than theother). To reduce the risk of electric shock, this plug is intendedto fit into a polarized outlet only one way. If the plug does notfit fully in the outlet, reverse the plug. If it still does not fit,contact a qualified electrician. Do not attempt to modify theplug in any way.

10

Description

a Lid

b Removable water containerc Water level indicator

d Warming plate for cupse Control selector

f On/Off indicator light (red)g Temperature control light (orange)

h On/Off switchi Brewing head

j Steam nozzlek Auto cappuccino accessory

K1 dialK2 flexible tube

K3 outlet nozzlel Removable overflow grid

m Removable drip trayn Measuring spoon

o Filter baskets for one or two cupsp Filter holder for ground coffee

q ESE filter holder and filter system

Safety recommendations

• Read these instructions carefully beforeusing your espresso machine.

• Do not plug the machine into anything otherthan a grounded electrical socket. Verify thatthe voltage indicated on the technicalspecifications plate on the bottom of theunit corresponds to your electricalinstallation.

• Do not place your espresso machine on ahot surface (an electrical heating plate forexample) or near a flame.

• Do not use the machine without the driptray and drip tray grid in place.

• Unplug the machine while cleaning.• Ensure that the electrical cord does not

come into contact with sharp or hot objects.Do not disconnect the electrical plug bypulling on the cord.

• Avoid touching the electrical cord as well asany other part which may become hotduring the use of the machine (steamnozzle).

• Never plunge the machine in water.• Keep the machine and the electrical cord out

of children’s reach.

• For descaling, adhere to the directions whichfollow.

• Do not use the machine if it is damaged or ifthe cord is in bad condition.

• The cord or any other defective elementmust be replaced exclusively by anauthorized Krups service center. Under nocircumstances should you open the machineyourself.

Espresso coffee

Your new Krups espresso machine has beenconstructed to make cafe quality espresso,cappuccino and latte at home. Espressocoffee is richer in aroma and stronger thannormal coffee. It is drunk from small pre-heated espresso cups. Hot water is passedthrough the ground coffee to obtain thisdelicious foamy, black coffee, which has aninvigorating effect.You can recognize an espresso by itscharacteristic aroma and its typical light brown“crema” found on top of the coffee. But thisrequires high pressure and an excellentespresso coffee which has been well roastedand correctly ground. If you cannot buyground espresso coffee, use a coffee grinderto grind the beans. The coffee must not beground too fine. It must be slightlygranulated. If it is too fine, you risk blockingthe grid of the brewing head and the filter.To guarantee complete success for yourespresso, you must also use freshly-drawnwater (so that it has not had time to stagnatein the air), without any chlorine odor and at afairly cold temperature.

Before first using your machine

Before using your appliance for the first time,clean the water heating system (withoutcoffee in the filter holder and filling the watercontainer once or twice) as follows:

11

• Open the lid and lift out the water containerusing the handle (1). Fill the water containerwith fresh, cold water (2).

• Replace the water container back into theappliance by positioning it firmly in thewater container compartment (3) and closethe lid.

The water level in the water container can bechecked at any time using the windowprovided for this purpose, so if necessary youcan add more water (4).• Turn on the appliance (5). The red operating

light and the orange temperature controlindicator light will both come on.

• Place one of the filter baskets in the filterholder (6). Then put the filter holder upagainst the appliance’s brewing head.

• To ensure that the filter holder is in thecorrect position, turn the handle so it pointsto the left at a 45 degree angle (6), placethe filter holder flat against the brewinghead, then turn the handle towards the right(7) as far as it can go (8).

• Place a container, as large as possible,beneath the filter holder (9).

• As soon as the orange indicator light goesoff, turn the selector to the setting (10)and allow all the water in the watercontainer to run through.

• If necessary, you can stop the operation byturning the selector to the O setting toempty the container, then resume operation.

Using the various functions ofyour espresso machine

1. ESPRESSO FUNCTION

. WITH GROUND COFFEE

For best results, we recommend that you firstpre-heat the accessories (filter holder, filterbasket and cups) without putting inground coffee. To do this :• Fill the water container with fresh, cold

water (1) (2) (3) and turn on the appliance(5). Empty the cups.

• Put the filter holder and an empty filterbasket in place (6) (7) (8), and place theespresso cups underneath.

• As soon as the appliance reaches the correcttemperature the orange indicator light willgo out.

• Turn selector to the setting (10).

• When the cups are full of hot water, resetthe selector to the O setting.

After making your first espresso and theappliance is hot, the espresso cups can thenbe pre-heated on the cup warming plate.

. Preparing an espresso :

• Fill the water container (1) (2) (3) and turnon the appliance (5).

• Put the filter basket for one or two cups intothe filter holder (6) .

• Place some ground coffee in the filter basket(1 or 2 measuring scoops), and then tamp itdown firmly; the coffee should reach the lipof the filter (12) (13).

• Remove any ground coffee which is lyingaround the filter (14).

• Replace the filter holder into the machine.Turn the filter holder until it is firmly lockedinto place. (16).

• Place one or two espresso cups beneath thefilter holder.

As soon as the appliance reaches the correcttemperature the orange indicator light will goout.

• Then turn the selector to the setting(17).

• When the cups are full, reset the selector tothe O setting.

• Remove the filter holder and the filter fromthe machine, and take out the coffeegrounds (18).

The filter basket can be refilled to make moreespressos.

Caution: if the water container is emptyand the pump is running, you will hear avery distinct noise, which is louder thanthe normal operating sound. If thishappens, turn the machine “off”. Checkthe water container and refill as needed.

Never let the pump run when the watercontainer is empty as this can damage thepump.

12

If you are preparing more than one cup ofespresso, disregard the orange thermostatlight. It simply indicates that the thermostat isregulating the temperature.

ESPRESSO FUNCTION WITH THE SPECIAL “ ESE “FILTER HOLDER

“ESE”, which stands for “Easy ServingEspresso”, is a selected measure of coffee,ground and pressed between two filter papersmaking a coffee pod which is ready to use (forexample “illy pods). This system makes iteasy for you to prepare your espresso and toclean the appliance.

The E.S.E. system was designed for makingItalian-style “espresso ristretto” or “shortespresso”. The amount of coffee is about twoounce and the water should take 20 secondsto run through.

We do not intend, or recommend, thatthe ESE servings are used for making a“long espresso”.We recommend that you take care whenhandling and storing the ESE servings so thatthey do not become deformed.For best results, we recommend that you pre-heat the accessories (filter holder, filter basketand cups) without any coffee. To do this:• Fill the water container with fresh, cold

water (1) (2) (3) and turn on the appliance(5).

• Put the empty ESE filter in place (7) (8) (9)and position the espresso cup underneath.

Once the appliance reaches the correcttemperature, the orange temperature controllight will go out.

• Then turn the selector to the setting(10).

• When the cup is full of hot water, reset theselector to the O setting.

Once the machine has heated up, theespresso cups can be pre-heated on the cupwarming plate (on top of the machine).

. Preparing an espresso:

Place the serving of “illy in the ESE filterholder fitted with its own filter. The wording“illy must be pointing towards the bottom.Setting the ESE podPlacing the ESE pod correctly will create aricher, thicker crema.

Tear excess paper from pod at perforatededge. Place the ESE pod with the REDMARKING FACE DOWN (bend the papercorners down).

LOCKING the handle TIGHTLY and PROPERLYwill avoid leakage from the filter holder andensure a better brewing cycle.

Place the filter holder inside the brewing headand FIRMLY turn the handle as far RIGHT aspossible.Once the appliance reaches the correcttemperature, the orange temperature controllight will go out.

• Then turn the selector to the setting (10).

• When the recommended quantity of coffeehas been reached (about two ounce) turnthe selector to the O position.

Remove the ESE filter holder from the brewinghead and throw away the used coffee pod.

NOTE: Other pods (such as those sold byStarbucks ) can be used in your Krups Novo3000 & 3000 Premium as long as they areE.S.E. standard pods.

illy is a registered trademark of illy espresso of theamericas, inc.Starbucks is a registered trademark of theStarbucks Coffee Company.

2. STEAM FUNCTION FOR PREPARING CAPPUCCINO

AND LATTE

The thumping noise which occurs while steamis being produced comes from theintermittent regulation of the pump and hasno effect on the proper working of theappliance.If you wish to make an espresso immediatelyafter using the steam function, the appliancemust first be allowed to cool down in order toachieve the correct temperature for preparingan espresso.• To do this, place a container below the filter

holder (without coffee) and positioncorrectly, then turn the selector to the setting (10).

• Allow the water to flow through until theorange indicator light comes on. Then turnthe selector to the O setting.

13

After this, you can make another espresso.Caution: during and after use of themachine, the metallic parts of the steamnozzle can become burning hot.

. Using the Krups Auto Cappuccinoaccessory (model FNC3 only)

The Auto-Cappuccino accessory makes it easyto produce frothy milk for makingcappuccinos, lattes and hot chocolates.

The milk is drawn in through the flexibletube and heated with the aid of steambefore coming out via the outlet nozzleof the auto cappuccino accessory.If the flexible tube is immersed directly in acarton of milk, a single cup is enough toprepare a cappuccino or a latte. You canadjust the amount of froth of the milk byusing the dial of this auto cappuccinoaccessory.

It is best to use fresh, skim or low-fat milk, notboiled, and well chilled (kept in therefrigerator). The container must also be cold(do not run it under hot water before frothingthe milk).For heating thick liquids, please refer to thesection “Heating thick liquids (e.g. soup)”

We recommend that you clean the autocappuccino accessory immediately after use -please refer to section “Cleaning theMachine”.

If you are making a cappuccino or latte, youwill need at least a 5 oz. cup (150 ml).Cappuccino is made using 1/3 espresso, 1/3hot steamed milk and 1/3 frothed milk. Cafélatte is made using 1/2 espresso, 1/2 steamedmilk, and topped with a bit of frothy milk.

• Fill the water container with fresh, coldwater (1) (2) (3) and turn on the appliance(5).

• Move the nozzle to the exterior of theappliance and mount the auto cappuccinoaccessory on the nozzle (22).

• Turn the dial to the setting (23).

• Immerse the flexible tube in the milk to beheated (you can use the Krups container orany other container) (24).

Once the appliance reaches the righttemperature, the orange temperature controllight will go out.

• Hold the container under the steam nozzleequipped with the cappuccino accessory insuch a way that the tip is immersed in themilk.

• Turn the selector to the setting (26).Keep the container straight during thisoperation. Do not allow the tip of thenozzle to touch the bottom of the containerbecause this could obstruct the steamoutput.

• Once you have obtained the desiredquantity of frothy milk, turn the selector tothe O setting.

• After use, remove the flexible tube from thecontainer and clean the auto cappuccinoaccessory (see section “Cleaning theMachine”).

. Preparing hot, steamed milk for a cafelatte, hot chocolate or for heating water(for tea, for example).

Notes:. Hot chocolate: immerse the flexible tubedirectly into the carton if the chocolate milk isready-made, or heat the milk if you are usingpowdered chocolate. Then mix the powder inthe heated milk.

• Move the nozzle to the exterior of theappliance and mount the auto cappuccinoaccessory on the nozzle (19).

• Fill the water container (1) (2) (3) and turnon the appliance (5).

• Turn the selector to the setting (20) .• Turn the dial of the auto cappuccino

accessory to the fine end of the settingscale (27).

• Immerse the flexible tube in the liquid to beheated. The tube must touch the bottom ofthe container.

• Place a container under the outlet nozzle.

Once the appliance reaches the righttemperature, the orange temperature controllight will go out.

• Turn the selector to the steam setting (21).

• Once you have obtained the desiredquantity of frothy milk, turn the selector tothe O setting.

14

• After use, remove the flexible tube from thecontainer.

. Using the Krups patented Perfect FrothAttachment

Krups patented Perfect Froth attachment Isavailable on all models. For the FNC3 modelyou will need to remove the auto-cappuccinoattachment and replace It by the Perfect FrothAttachment in order to execute this operation(36).You can use the Perfect Froth attachment tofroth milk for cappuccinos, Lattes and hotchocolates as well as heating any liquid (waterfor tea or thick liquids for soups)

• Fill the water container (1) (2) (3) and startthe appliance (5).

• Move the steam nozzle to the exterior of theappliance.

• Turn the selector to the setting (20).

Once the appliance reaches the correcttemperature, the orange temperature controllight will go out.

• Immerse the steam nozzle in the containerholding the liquid to be heated.

• Then turn the selector to the setting (21)until the liquid is hot enough, then reset theselector to the O setting and remove thecontainer.

• For liquids other than water, turn theselector to the setting (20) for thefollowing cleaning operation in order toprevent any blockage of the opening of thesteam nozzle :

• place an empty container below the steamnozzle.

• select the setting again (21) to removethe residue of the liquid.

• turn the selector to the setting O.

• Clean the steam nozzle with a damp cloth.

• For more thorough cleaning of the nozzle,please refer to the paragraph onmaintenance.

Cleaning the Machine

- Never wash your espresso machineaccessories in the dishwasher.

After use, the water container must beemptied.. Removable drip trayAfter using the appliance, remove theoverflow grid and empty the removable driptray (30) (31). If several espressos are beingprepared one after the other, the drip trayshould be emptied from time to time (aboutonce every 7 - 8 espressos). If necessary, cleanthe drip tray and its grid with water and alittle non-abrasive dishwashing liquid, rinseand dry. When reassembling the machine,ensure that the plastic lining is in the rightplace (32).. The brewing head, the filter basket andthe filter holderThese must be cleaned after each use. All youneed to do is wipe a damp cloth over thebrewing head of your appliance and to washthe other accessories in water and a little non-abrasive dishwashing liquid, rinse and dry.

If the brewing head is heavily clogged up,unscrew the grid using a coin, clean it andrefit it, pressing down firmly (33).When your espresso machine is not beingused, do not leave the filter holder in theappliance to prevent wear on the gasket.. The cup warming plate: remove this toclean it with water and a little non-abrasivedishwashing liquid, rinse and dry (34).. Steam nozzle: wipe with a damp cloth aftereach use.

. The auto cappuccino accessoryAfter each use, we recommend that you rinsethe auto cappuccino accessory in thefollowing manner:• Turn the selector to the steam pre-heating

position (19).• Turn the dial to the cleaning position (37).• Immerse the flexible tube into a glass of

water. (The minimum quantity necessary is 3to 4 ounces/30-60 ml).

• Place an empty container below the outletnozzle.

Once the appliance reaches the correcttemperature, the orange temperature controllight will go out.

• Then turn the selector to the steam setting(26).

• When all the water has run through the

15

auto cappuccino accessory turn the selectorto the O position.

• After use, remove the flexible tube from thecontainer.

• Once this operation is completed, clean theoutlet nozzle with a damp cloth.

We recommend that you regularly dismantlethe auto cappuccino accessory and clean itwith water, a little non-abrasive dishwashingliquid and a small brush. Rinse and dry beforereassembling it (38).Be careful to mount the flexible tube theright way: engage the straight cut end intothe auto cappuccino accessory.

. Brewing head gasketFrom time to time this gasket must becleaned :

• Put the filter basket in the filter holder andplace the filter holder in the machine.

• Place a container under the filter holder.• Turn on the appliance.

• Turn the selector to the setting .• When the hot water starts to filter through,

turn the filter holder slowly from left to rightso that the water filters through betweenthe gasket and the filter.

Descaling

• Descaling of your espresso machine shouldbe done fairly frequently with citric ortartaric acid.

The guarantee does not include espressomachines which do not function, or donot function properly, because descalinghas not been carried out.However, we would advise you to use theKrups descaling solution which is availablefrom Krups. Descaling depends on thehardness of the water, but also on thefrequency of use.

- Then follow the following method:• Unscrew the grid from the brewing head of

the appliance and clean it.• Dissolve 2 tsp/10 ml of the descaling product

or a packet of KRUPS descaling solution, in17 oz/510 ml of lukewarm water and pourthe whole batch into the empty watercontainer.

• Place a container under the brewing head.Run through about 1/3 of the liquidimmediately, setting the selector to theposition (10).

• Stop the appliance, leaving the position (10)engaged and wait for 10 - 15 minutes toallow the descaler to take effect.

• Next, start the machine again and allow therest of the liquid to run through.

• Then rinse with two water containers offresh water and replace the grid on the headof the appliance (see section on “Cleaningthe Appliance”).

Problems, probable causes andhow to correct them

Problems Probable causes Corrective actions

Espresso not hot Cups, filter and Preheat theenough filter holder accessories (cups,

are cold. filter, filter holder)See paragraph«Preparing anespresso».

Coffee leaks The filter holder See paragrapharound the filter is not mounted «Preparing anholder correctly or has espresso».

not been tightenedsufficiently.There are coffee Clean around thegrounds on the filter and theedge of the filter gasket.

The brewing head Clean the gasketgasket is dirty. with a damp cloth.

The brewing Contact anhead gasket approved Krupsis defective service centre.

Pump is very noisy No water in the Fill the water tank.water tank.

Water tank incor- Press firmly downrectly mounted. on the water tank.

Coffee grounds too Use fresh coffeeold or very dryand the pump can-not producepressure.

16

Water does not run No water in the Fill the water tank.through water tank. Press firmly down

Water tank incor- on the water tank.rectly mounted.

The filter is blocked, Clean the filter andthe coffee grounds the grid on theare too fine or head.tamped down too See the paragraphhard. «Maintenance»

and try a coarsercoffee.

Brewing head Put the grid togrid is encrusted soak in descaling

solutionSee paragraph«Maintenance».

Appliance needs See paragraphdescaling. «Descaling».

Water runs through Coffee grounds too Try a finer coffeetoo quickly coarse

Quantity of Use the spoonground coffee provided tois insufficient. measure out the

coffee.

Coffee grounds not Tamp down thetamped down coffee again.firmly enough

The espresso has Coffee grounds Try a finer-groundno froth (crema on too coarse coffecoffee)

Coffee grounds Tamp down thenot tamped coffee again

Coffee grounds Use fresh coffeestale or too dry

The milk is not very Steam nozzle bloc- See paragraphfrothy ked «Maintenance»

Cappuccino acces- See paragraphsory blocked «Maintenance»

Milk not fresh. Use fresh milk

Milk is lukewarm. Put milk inrefrigerator.

Lots of water on Grounds not Tamp down thethe coffee grounds properly tamped grounds

down

Insufficient quantity Increase theof ground coffee quantity of ground

coffee.

Recipes

Savor your espresso just as you like it: whenyou want to relax or to top off a good meal.

Here are a few recipes which you will be ableto create with your espresso machine.

. Original espresso

• Take one measuring spoonful of goodquality well roasted espresso coffee, andmake an espresso directly into a pre-heatedcup.

If you use good, finely ground coffee, the cupwill be crowned by a fine head of goldenfroth (crema).• Add sugar if desired and enjoy.

. Cappuccino

For a state of the art cappuccino, the idealquantities are as follows: 1/3 coffee, 1/3 hot,steamed milk, 1/3 frothy milk.• Use 5 oz. cups/150 ml which have been pre-

heated.

• Fill them with 1/3 espresso coffee. Usingthe auto cappuccino accessory, fill the cupwith another 1/3 of steamed milk and 1/3of froth.

• Lastly, sprinkle with drinking chocolatepowder or cinnamon.

. Cafe latte

For a state of the art latte, the ideal quantitiesare as follows: 1/2 coffee, 1/2 hot, steamedmilk topped with some frothed milk.

• Prepare a classic espresso in a large cup.• Add steamed milk.

• Top with some froth.

. Iced coffee à l’Italienne

4 vanilla ice cubes, 2 cups of cold, sweetenedespresso, 4 ounces milk, fresh cream, gratedchocolate.• Mix the cold espresso with milk.

• Distribute the ice cubes among the glasses,pour the coffee over them and decoratewith fresh cream and grated chocolate.

. Friesian coffee

• Add a small glass of rum to a sweetenedcup of espresso.

17

Limited One Year Warranty

Your KRUPS # FNC2/FNC3 is covered by thefollowing warranty :

If within one year from date of purchase thisKRUPS product fails to function because ofdefects in materials or workmanship, KRUPSNorth America will, at its option, repair orreplace the unit without charge, provided theowner has a proof of date of purchase.

This warranty will be void if malfunction wascaused by damage to the product by accident,misuse, use on frequency or voltage otherthan marked on the product and/or describedin the instructions, abuse including tampering,damage in transit, or use for commercialpurposes. This warranty gives you specificlegal rights, and you may also have otherrights which may vary from state to state.

• Top with a good layer of fresh cream andserve.