kompaktna stanica polytron
DESCRIPTION
Upute za kompaktnu stanicu PolytronTRANSCRIPT
AVT 1
User manual
0901489
INDEX
1. GENERAL DESCRIPTION.
2. SAFETY INSTRUCTIONS.
3. OPERATING ADJUSTMENTS.
4. CONNECTIONS.
5. INSTALLATION.
6. INSTALLATION EXAMPLE.
7. TECHNICAL SPECIFICATIONS.
1. GENERAL DESCRIPTION
Thank you for buying this digital terrestrial
modulator.
Please read this manual carefully to
install, use and maintain the modulator in
the best conditions of performance. Keep
this manual for future consults.
The product you have acquired is a state
of the art which main characteristics are:
• DVB-T modulator compatible with
standard ETSI EN 300 744 v1.5.1
• Fully compatible with standard DVB-
T/H.
• CVBS video input( via RCA ) or S-
VHS.
• Stereo.
• VHF-UHF band( 47~860 MHz )
• Generation of PSI tables: PAT, PMT;
SI: SDT, NIT.
• Generation of LCN ( Logic Channel
Numbering ).
• PAL and NTSC video formats.
• Picture aspect ratio: 4:3, 16:9 and AUTO
( depends of WSS on video source )
• 2K mode operation.
• Constellation of 16QAM and 64QAM.
• Different types of channels regions (
Australia, Western Europe… )
• Editable channel name and network
provider.
The supervision and control of AVT 1 is
done by LCD display. It is configured by an
intuitive navigation menu. Start to enjoy AVT
1.
NOTE The contents of this company manual are copyrighted and must not be duplicated or copied in any form, either partially or in full, without the prior consent of the creator. Changes in this company manual which are carried out without consent of the creator can lead to the loss of the guarantee or to the rejection of the product liability on the part of the manufacturer. The creator is grateful for suggestions for improvement.
Creator: Polytron-Vertrieb GmbH
Postfach 10 02 33 75313 Bad Wildbad
Germany
The following emphases are used in this manual with the following meanings:
NOTE apply to technical requirements which the user of the equipment must particularly take into account to ensure a faultless function of the equipment/plant.
ATTENTION refers to instructions which have to be adhered exactly to avoid damage or destruction of the device.
CAUTION stand for instructions whose nonobservance doesn't exclude the endangering of persons.
At references to a component e.g. (figure 1/3) provided by a place number the reference to picture 1 place number 3 refers in this example.
2. Safety instructions Before taking the unit into operation please read the following safety precautions carefully! Important: The unit should only be opened by qualified persons. The unit must be disconnected from its power supply before service work is carried out. When the unit is open parts may be accessible through which dangerous voltages flow and with which contact may endanger your life. To guarantee the EMC protection of the amplifier the lid must be bold tight again after opening the amplifier.
Ambient temperature The ambient temperature should not exceed a range of 0 °C to +50 °C (32 °F to 122 °F). Humidity The unit may not be exposed to water drops or spray. If condensation is present, wait until the unit is dry before taking it into operation. Mains connection and mains cable By units with the power supply safety class I, the wire which is coloured green/yellow must be connected to the terminal in the plug marked with the letter "E" or by the earth symbol . The blue coloured wire must be connected to the terminal marked "N" and the brown coloured wire to the terminal marked "L". Units which operate with a remote feeding supply may not be connected to 230 VAC. To do so will endanger your life! At units with the power supply safety class II, the housing of the unit must be connected to ground at the place indicated in the operating instructions of the unit. The ground terminal of the plug is in the case not connected. Grounding of system According to EN 50 083 / VDE 0855 regulations, the antenna system must comply with the safety regulations e.g. grounding, potential equilization etc. Precautions to ensure the electro magnetic compability (EMV) All covers and screws must tightly be fitted and should be tightly fastened. Contact feathers should not be oxidated or deformed.
Any tampering can be dangerous and can perform the warranty invalid.
The modulator is powered with a voltage of 7.5VDC. The power supply voltage
must not exceed that otherwise the modulator could suffer irreparable damage and
subsequent invalidation of the warranty. Therefore:
Do not replace power supply with a voltage greater tan 7.5VDC. � Do not connect the modulator to the power if the power cord is damaged. � Do not plug the modulator into mains supply until all cables have been connected
correctly. � Do not cut the cord. • Modulator shall not be exposed to dripping or splashing water and no objects
filled with liquids, such as vases, shall be placed on it.
• Avoid placing modulator next to central heating components and in areas of high
humidity.
• Do not cover modulator elements that obstruct the ventilation slots and avoid
overheating.
• If the modulator has been kept in cold conditions for a long time, keep it in a warm
room no less than 2 hours before plugging into the mains.
• Mount the modulator in vertical position with the connectors located on the bottom
side.
• From top, front and bottom of installed modulator must be at least 10cm free
space.
Connect modulator to ground connection with terminal provided
(see point 5-B).
3. OPERATING ADJUSTMENTS
3.1 MODULATOR BOOT
When modulator is booting display shows firmware version during 2 seconds:
Next message shown is:“Booting…”
During that period of time the module is loading the firmware and initiating
internal devices.
Once started on the screen:
This message indicate modulator output channel, where XX is output channel (depends channel region selected ) and FFFFFF is frequency in kHz including
fine adjustment. Example:
*Output channel: C21 ( Western Europe ) with 25kHz of fine adjustment.
Note: switch menu language to English holding simultaneously down
buttons at power on. This operation can help you to restore bad
language configurations.
V20101214
Booting...
Running... XX (FFFFFF
Running... 21 (474025 )kHz
BASIC MENU ATTENUATION
BASIC MENU LANGUAGE
OUTPUT
ATTENUATION 30 %
BASIC MENU EXIT
BASIC MENU OUTPUT
3.2 FAST CONFIGURATION Default configuration is: - Channel Region: WESTERN EUROPE - Output Channel: C28 - Guard interval: 1/16 - Channel name:CH A - Attenuation: 30% - PID Video: 33 - Network name: NET A - Constelation: QAM16 - PID Audio: 34 - Video input: CVBS - FEC:3/4 With buttons you can do a fast channel change, press for confirmation.
Press to enter menu. Select “BASIC MENU” and press to enter.
In this menu you can change basic parameters as: Output channel, attenuation and
language.
1) Adjust output channel depending on the selected
channel region.
With buttons select desired channel and press
to confirm.
2) Adjust output level of the modulator, select attenuation
value between 0 to 100% ( 15 dB typ. )
3) Select menu language.
AVT 1 has 11 installed languages. Remember that
switch menu language to English holding
simultaneously down buttons at power on.
4) Exit from basic menu with
OK
OK OK
OK
OK
OUTPUT CHANNEL
ADVANCED MENU
CHANNEL REGION
ADVANCED MENU
FINE ADJUST 786100 kHz
ADVANCED MENU
ADVANCED MENU
ADVANCED MENU
ATTENUATION 30 %
CONSTELLATION QAM16
3.3 ADVANCED CONFIGURATION
Press to enter menu, select “ADVANCED MENU” and press to enter.
This menu allows you to adjust advanced parameters of modulator. 1) Select channel region to be used.
Note: depends of channel region selected,
modulated signal will have a center frequency and
bandwidth, select the correct region as location of
installation, otherwise you may have tuning problems.
2) Adjust output channel depending of selected
region. With buttons change output channel and
press to confirm.
3) Adjust center frequency of modulated
channel. Fine adjust allows to change center
frequency between ±100kHz.
Display shows output frequency including offset.
4) Adjust the output level of the modulator
according to your installation, select the attenuation
value between 0 and 100% (15 dB typ.)
5) Select constellation of modulated signal.
Select between QAM16 and QAM64.
OK OK
OK
ADVANCED MENU
FEC 7/8
ADVANCED MENU GUARD INTERVAL
GUARD INTERVAL 1/16
ADVANCED MENU
SPECTRUM INV. OFF
ADVANCED MENU VIDEO PID
VIDEO PID 33
ADVANCED MENU PID AUDIO
PID AUDIO 34
ADVANCED MENU VIDEO BITRATE
VIDEO BITRATE 6144kbps
6) Adjust FEC (Forward error correction). FEC
adjust can be changed between:1/2, 2/3, 3/4,5/6,7/8.
7) Adjust Guard Interval between:
1/4, 1/8, 1/16 1/32.
8) Turn on or off spectral inversion. With this
function you can prevent incompatibilities in the
reception of modulated channel.
Note: this function is disabled by default.
9) Select video PID.
Adjust between 33 and 8190.
10) Select audio PID.
Adjust between 33 and 8190.
Note: video PID and audio PID must be different.
11) Adjust VIDEO BITRATE between 6144kbps
and 12288kbps with 512kbps steps.
AUDIO BITRATE 192kbps
ADVANCED MENU CHANNEL NAME
CHANNEL NAME CH A
ADVANCED MENU
NETWORK NAME
ADVANCED MENU NETWORK ID
NETWORK ID 0xhhhh
12) Adjust AUDIO BITRATE between 128kbps
and 384kbps with 64kbps steps.
Note: the audio and video BITRATE adjustment
should be done within the margins allowed by the
selected modulation ( constellation, FEC, guard
interval).
13) Edit modulated channel name.
14) Edit network name.
Note: Select char to be changed with buttons, char appears blinking,
press to select char (it appears underlined) and with select new
char, confirm change with . To save new name press until end of line
(see that any char appears blinking) and press . New name will be stored in
memory.
15) Edit network identificator.
Network ID should be set according to the ETSI TS
101 162 Norm and following your country
regulation.
OK
OK
OK
ADVANCED MENU LCN
LCN OFF
ADVANCED MENU VIDEO SOURCE
VIDEO SOURCE CVBS
ADVANCED MENU VIDEO STANDARD
VIDEO STANDARD PAL
ADVANCED MENU ASPECT RATIO
ASPECT RATIO AUTO
ADVANCED MENU BRIGHTNESS
ADVANCED MENU CONTRAST
16) Set LCN of modulated channel.
Logical Channel Number (LCN), also known as virtual
channel, is a channel designation which differs from
the actual radio channel or frequency on which the
signal travels.
17) Select video input.
Select between CVBS (Composite video baseband
signal, RCA connection) and S-VHS (video format in
which video information is encoded in two channels.
Brightness/luminance (Y) in one channel, and
color/chrominance (U and V) in other channel, S-Video
connection).
18) Select video standard to be used. Select
between PAL and NTSC.
19) Select aspect ratio. Select 4:3, 16:9 and
AUTO.
Note: AUTO depends of WSS (Wide Screen
Signaling) from video source.
20) Adjust image brightness.
21) Adjust image contrast.
ADVANCED MENU SATURATION
ADVANCED MENU DEFAULT CONFIG.
ADVANCED MENU EXIT
ADVANCED MENU LANGUAGE
22) Adjust color saturation.
23) Select menu language.
AVT 1 has 11 installed languages. Remember that
switch menu language to English holding
simultaneously down buttons at power on.
24) Make a factory default with this option.
Note: this operation is undoable if you
make a factory default all data inserted by user will be
deleted. Modulator will restart after default
configuration function made.
25) Exit from advanced menu with
4. CONNECTIONS 1. Power supply: 7,5VDC/2A.
2. RS-232 Connector for PC.
3. RF Output.
4. S-VHS video input.
5. RCA video input.
6. RCA right audio input.
7. RCA left audio input.
8. Ground connection..
OK
5. INSTALLATION
A. Screw modulator where you want
to install it.
Remember: From top, front and
bottom of installed modulator must
be at least 10cm free space.
B. Connect modulator ground to
installation ground, as shown in
picture.
WARNING: For the protection of your equipment and its proper working is necessary to connect the modulator to a ground connection.
C. Connect cables to audio/video source.
D. Connect RF out to distribute modulated signal.
6. INSTALLATION EXAMPLE
According to the WEEE (Waste Electrical and Electronic Equipment) EU Directive, do not dispose of this product as household waste or commercial waste. Waste electrical and electronic equipment should be appropriately collected and recycled as required by practices established for your country. For information on recycling of this product, please contact your local authorities, your household waste disposal service or the shop where you purchased the product.
7. TECHNICAL SPECIFICATIONS
.
Polytron-Vertrieb GmbH
Postfach 10 02 33
75313 Bad Wildbad
H.Q. Order department
+ 49 (0) 70 81/1702 0
Technical hotline + 49 (0) 70 81/1702 - 12
Telefax + 49 (0) 70 81) 1702 - 50
Internet http://www.polytron.de
eMail [email protected]
Technische Änderungen vorbehalten
Subject to change without prior notice
Copyright © Polytron-Vertrieb GmbH