km2v80 service manual
DESCRIPTION
Manual de servicio motor Kipor KM2V80TRANSCRIPT
![Page 1: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/1.jpg)
Thank you for purchasing Kipor KM2V80 series diesel engine. In order to ensure proper operation, reliable running and good economic benefit of your machine, it is especially important for you to operate correctly and maintain carefully. This manual will tell you how to operate and maintain the machine correctly, it will also give you detail instruction about the main technical specification, configuration and troubleshooting. Content Instruction of products……………………………………………………………………………..1 1. Brief instruction of products……………………………………………………………....1
2. Composition of model and its meaning………………….………………………………1 3. External installation drawings and names of parts……………………………………. 2 4. Specification………………………………………………………………………………. 6 5. Main adjusting parameter………………………………………………………………… 7 6. Tighten torque values of main bolts and nuts……………………………………………7 7. Fit clearance and interference table………………………………………………………8
Technical maintenance………………………………………………………………………………9 1. Daily check and periodic check …………………………………………………….9
2. Procedure of periodic maintenance………………………………………………………..9 Disassembly and reassembly…………………………………………………………………….. 13 1. Basic procedure of disassembly…………………………………………………………..13
2. Basic procedure of reassembly……………………………………………………………18 Check and maintenance……………………………………………………………………………22 1. Cylinder cover…………………………………………………………………………….. 22
2. Camshaft...............................………………………………………………………………23 3. Piston and piston pin……………………………………………………………………… 24 4. Crankshaft………………………………………………………………………………… 25 5. Cylinder block and cylinder cover................................................................................ 6. Lubrication system……………………………………………………………………….. 27 7. Cooling system…………………………………………………………………………… 27 8. Fuel system……………………………………………………………………………… 28
The electrical system…………………………………………………………………………… 29 1. Starter motor……………………………………………………………………………… 29 2. Heater plug............…………………………………………………………………… .31
Troubleshooting and remedy of engine………………………………………………………...35 Preliminary run...........................................................................................................….........39
![Page 2: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/2.jpg)
Instruction of products 1. Brief instruction of products This model is double cylinder, V-type, four strokes, water cooled, and swirl type diesel engines.
This model will be exploited into multi-purpose engine with vertical or horizontal shaft. This model is simple in structure, convenient in disassembly or reassembly, and have smart size, short axial length, light weight, good performance, reliable quality, long running time. They will meet various demands for each customer, and are ideal complementary power for generating sets, construction machinery, ship, combined harvester, agricultural machine etc. Welcome you to purchase. 2. Composition of model and its meaning
KM 2 V 80
Cylinder bore (mm)
V-type
Cylinder No.
Kipor
![Page 3: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/3.jpg)
Introduction of products 3. External installation drawings and name of parts Please refer to picture 1, picture 2, picture 3 and picture 4 for details.
Picture1 Vertical section view for KM2V80 diesel engine
![Page 4: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/4.jpg)
Picture 2 Horizontal section view for KM2V80 diesel engine
![Page 5: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/5.jpg)
Picture 3 Vertical figuration view for KM2V80 diesel engine
![Page 6: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/6.jpg)
Picture 4 Horizontal figuration view for KM2V80 diesel engine
![Page 7: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/7.jpg)
4. Specification Table 1 Main specification table of KM2V80 diesel engine
Model KM2V80
Type Double cylinder, V-type, water-cooled, 4 stroke, swirl
type
Bore×Stroke mm 80×79
Displacement L 0.794
Compression ratio 23
Rated output/Rated speed
kW/r/min 12.5/3000 14.5/3600
Max. torque N·m 49/1600~1800
Min. speed (zero load) r/min ≤900
Lubricating system Pressure splashed
Starting system Electric starter
Output terminal direction (face
to the flywheel) Anticlockwise
Fuel type 0#(summer), -10# or -20#(winter), -35#(chillness)
Fuel consumption ratio g/(kW·h) 285 297
Lube oil type SAE 10W-30、20W-40 or L-ECD Grade
Lube oil capacity L 2.27
oil consumption ratio g/(kW·h) ≤5
Starting motor capacity V,kW 12V 1.4 kW
Charging generator capacity
(V,A) 12V 20A
Battery capacity (V,AH) 12V 60AH
Overall dimension (L×W×H) mm 616×486×528
Net weight kg 58
![Page 8: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/8.jpg)
5. Main adjusting specification Table 2 Main adjusting specification of KM2V80 diesel engine
Item Standard value Cylinder compression clearance height mm
0.88~1.2
Advanced angle of fuel supply BTDC 18.5°±1° Fuel spraying pressure Mpa 13°±0.5°
Inlet valve Open at BTDC 22° Close at ABDC 56°
Valve timing
Exhaust valve Open at BTDC 61° Close at ATDC 26°
Valve clearance mm (cooled state) 0.10~0.15 Valve sunk volume mm 0.5±0.10 Oil pressure Mpa 0.25~0.5 6. Tighten torque of main bolt and nut
Table 3 Tighten torque of main bolts and nuts Value
Item Thread
Tighten torque (N·m )
Remark
Cylinder cover bolt M9×1.25 60±5 Connection rod bolt M7×1 28±2
Flywheel bolt M10×1.25 75~80 Crankcase cover bolt M8×1.25 22~25
Fuel injector bolt M20×1.5 50±5 Heater plug M10×1.25 12±2
M6×1.0 8~12 M8×1.25 17~23 M10×1.5 40~50
M12×1.75 85~100 M14×1.5 130~150
General bolt: mechanical performance is 8.8 grade
M16×1.5 220~240
![Page 9: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/9.jpg)
7. Fit clearance and interference table Table 4 Fit clearance and interference table
No. Name Standard dimension(mm) Fitting clearance
(mm) Remark
1 Cylinder inner diameter/ Piston top outer diameter
φ80H7(+0.03 0 )/d-0.515±0.01
0.565~0.635
2 Cylinder inner diameter/ Piston skirt upper part
φ80H7(+0.03 0 )/d-0.125±0.01
0.175~0.245
3 Cylinder inner diameter/
Piston skirt diameter φ80H7(+0.03
0 )/φ80-0.06 -0.08
0.06~0.110
4. Piston pin hole/Piston pin φ20-0.002 -0.008/φ20 0
-0.006 0.004~-0.008
5 The width of ring groove /
The height of 1st ring 1.2+0.060
+0.040/1.2-0.01 -0.02 0.05~0.08
6 The width of ring groove /
The height of 2nd ring 1.5+0.040
+0.020/1.5-0.01 -0.02
0.03~0.06
7 The width of ring groove /
The height of 3rd ring 3.0+0.030
+0.010/3-0.01 -0.02
0.02~0.05
8 Open clearance of 1st ring 0.25~0.35 9 Open clearance of 2nd ring 0.20~0.35
10 Open clearance of 3rd ring 0.15~0.30
11 Connection rod bushing/
Piston pin diameter φ20+0.025
+0.015/φ20 0 -0.006 0.015~0.031
12 Connection rod bush hole diameter/
Connection rod journal φ40+0.032
0 /φ40f5(-0.025 -0.036) 0.025~0.062
13 Main bearing bushing hole diameter/
Main journal φ50+0.035
+0.015/φ50f5(-0.025 -0.036)
0.040~0.071
14 Crankshaft axial clearance 120.7+0.10 0 /108.6+12=120.6 0
-0.10 0.10~0.30
15 Crankshaft axial open split/
The width of connection rod big head40+0.25
+0.10/20-0.15 -0.20×2=40-0.30
-0.40 0.40~0.65
16 (Crankshaft center line to the tank
top)/(piston + connection rod + crank radius)
13.01.1935.395.1251.2803.054.193
±=++±
0.28~0.60
17 Camshaft hole diameter/
Camshaft journal φ18H7(+0.018
0 )/φ18e6(-0.032 -0.043)
0.032~0.061
18 Side cover camshaft hoe diameter/
Camshaft journal φ24H7(+0.021
0 )/φ24f6(-0.040 -0.053)
0.040~0.074
19 Camshaft axial clearance 176.5+0.10 0 /164.1+12.2=176.3±0.05 0.035~0.15
20 Valve tappet hole/ Tappet diameter
φ10H7(+0.015 0 )/φ10e7(-0.025
-0.040) 0.025~0.055
21 Fuel pump tappet hole/
Fuel pump tappet φ21H7(+0.021
0 )/φ21-0.047 -0.080
0.047~0.101
22 Valve pipe/ Inlet valve φ6H7(+0.012 0 )/φ6-0.030
-0.045 0.03~0.057
![Page 10: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/10.jpg)
23 Valve pipe/ Exhaust valve φ6H7(+0.012 0 )/φ6-0.035
-0.050 0.035~0.062
24 Cylinder cover pipe hole/
Valve pipe φ10H7(+0.015
0 )/φ10+0.055 +0.045
-0.03~-0.055
25 Cylinder cover housing washer hole/
Inlet valve housing washer φ33.5H7(+0.025
0 )/φ33.5+0.12 +0.09
-0.065~-0.012
26 Cylinder cover housing washer hole/
Exhaust valve housing washer φ28H7(+0.021
0 )/φ28+0.11 +0.09
-0.069~-0.11
27 Cylinder cover insert/
Combustion chamber insert φ32.5H7(+0.021
0 )/32.5p6(+0.042 +0.026)
-0.005~-0.042
28 Cylinder cover rocker shaft hole/
Rocker shaft diameter φ12H7(+0.018
0 )/φ12f6(-0.016 -0.027)
0.016~0.045
29 Rocker arm hole/
Rocker shaft diameter φ12H7(+0.018
0 )/φ12f6(-0.016 -0.027)
0.016~0.045
30 Timing gear hole/ Camshaft journal
φ24H7(+0.021 0 )/φ25s6(+0.048
+0.035) -0.014~-0.048
31 Crankshaft gear hole/
Crankshaft journal φ50H6(+0.016
0 )/φ50p5(+0.037 +0.026)
-0.010~-0.037
32 Flywheel gear ring hole/
Flywheel stop ring φ214H7(+0.046
0 )/φ214u7(+0.364 +0.258)
-0.212~-0.304
33 Connection rod small head hole/
Connection rod bushing outer diameter
φ22H7(+0.013 0 )/φ22r6(+0.041
+0.028) -0.015~-0.041
34 Connection rod bolt hole/
Bolt location diameter φ7.5H7(+0.015
0 )/φ7.5f6(-0.013 -0.022)
0.013~0.037
35 Side cover outer rotor diameter/
Outer rotor diameter φ41H7(+0.025
0 )/φ41-0.075 -0.115
0.075~0.14
36 Side cover oil pump shaft diameter/
Shaft diameter φ11H7(+0.018
0 )/φ11f6(-0.016 -0.027)
0.016~0.045
37 Inner/outer rotor hole depth/ Inner/outer rotor axial depth
12+0.08 +0.04/12 0
-0.020 0.04~0.10
![Page 11: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/11.jpg)
Technical maintenance 1. Daily check and periodic check
Engine’ performance will be deteriorated if the operation condition becomes worse or time prolongs, such as: fuel and oil consumption increase, exhaust harmful substance increases, or vibratory and noise increase. Please strengthen the maintenance service of engine, insist on daily check and periodic maintenance, which will prove efficiency and prevent fault.
Check can be divided into daily check and periodic check. Daily check: Do daily check before starting engine, and operate it as a rule. Periodic check: Suggest you make a running diary, writing down results of everyday
operation and check, accumulating total running time. Start your periodic check and maintenance according to below table (table 5).
Periodic check can be divided into: 50h、250h、500h、1000h、2000h(h: hours) Time interval of periodic check can be properly advanced or delayed according to the
engine’s purpose, location condition, fuel or lube oil’s quality and other using conditions. Table 5 Periodic check table of engine
System Checking item Everyday 50h 250h 500h 1000h 2000hCheck and refill fuel oil ○ Check for oil leakage ○ Drain out fuel oil ○
Fuel
Replace the oil filter element ◎ Check and refill lube oil ○ Check for oil leakage ○ Replace lube oil
Lube oil
Replace lube filter element first ◎
time seco◎
nd time Check and refill cooling water ○ Clean radiator element ○ Replace cooling water ◎
Cooling water
Wash and maintain cooling system
●
Robber pipe
Replace fuel pipe and cooling water tube
○ ◎
Speed regulator operation ○ Operation system Idle adjust ●
Inlet system
Clean and replace air cleaner element
○clean ◎
Check alarm ○ Electric parts
Check electrolyte and charge the battery
○
Adjust clearance of intake/exhaust valve
○first time
○second time
Cylinder cover
Wear of intake/exhaust valve sealing ring belt
●
![Page 12: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/12.jpg)
○:check ◎:replace ●:Contact with Kipor agent
2. Procedure of periodic check 2.1 First 50h operation check At the beginning time of operation, the inner parts wear mutually and the lube oil is polluted soon, so please replace the lube oil and oil filter element. Oil draining is much easier
and quicker when the engine is hot. Notice: Prevent be scalded when draining out the hot oil, and don’t let the hot oil splash on you. 2.1.1 Drain out lube oil: Prepare an oil basin to store oil before draining, loosen the drain screw with a spanner, and then begin to drain oil. Make sure you have tightened the drain screw after draining to prevent be dropped out. Danger: Indicate that severe damage will result if you haven’t tightened the drain screw. 2.1.2 Replace oil filter element: Revolve down the oil filter element with a filter element spanner in anticlockwise direction, clean the oil filter seat, smear a thin lube oil on the filter element sealing gasket before replacing, revolve hard with hand in clockwise direction, then revolve 3/4 circle with filter element spanner.(Tighten torque valve20-23N.m) 2.1.3 Refill fuel, about 6.9L. Run the engine 5 minutes to preheat the engine, and check for oil leakage. Recheck fuel after stop running 10 minutes, and refill to the upper limit line. After the initial maintenance, replace fuel and oil filter element regularly per 250h interval.
2.2 Check per 50h operation 2.2.1 Drain out fuel tank: Prepare an oil basin; revolve down the drain screw, drain out water and
other foreign matter in the fuel tank; install drain screw and tighten up, check for oil leakage. 2.2.2 Check battery: Disconnect battery negative electrode earth wire when checking the electric
appliance system, or fire will result by short circuit; Make sure to be well-ventilated, or hydrogen caused during charging will burn; Check battery electrolyte and refill to the upper limit location if it is gong to reach the lower one, otherwise life of battery will be shorten, or even explosion will be caused. You should always check and refill distilled water since electrolyte lever drops down quickly in summer. Please recharge the battery if rotation speed of crankshaft is slower than normal and starting is failure. If you still can’t start the engine after recharging, replace the battery.
2.2.3 Clean air filter: Air filter element will easily be polluted by dust, oil mist or steam, which will result in increase of intake resistance, decrease of intake volume, and black smoke of engine, so you should always check and clean the oil filter element, or even replace it; Cleaning should be more frequent if operating at
Check and adjust fuel injection pressure
○
Timing check and adjust of fuel injection
○
Fuel injector and fuel injection
pump Maintenance of fuel injector and fuel injection pump
●
![Page 13: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/13.jpg)
Picture 6 Clean air filter places full of dust(such as quarrying plant, coal yard or road building plant), foreign matter inside the oil filter should be cleaned; Take out filter element parts from air filter shell, blow dust down with compression air. Please replace filter element parts if papery filter element is broken. Clean oil sludge inside the air filter; cover the air inlet port with cloth to prevent some other matter dropping into the air inlet manifold. 2.2.4 Install the air filter, pay attention to the sealing condition between filter element and connecting pipe to prevent air entering into cylinder not through filter element. 2.3 Check per 250h operation 2.3.1 Replace lube oil and filter element inside the oil filter, replace once per 250h operation from the second time. 2.3.2 Check and clean radiator element: Dust and dirt adhesion on the radiator element will reduce radiator’s cooling performance and result in engine’ overheat, you can advance the cleaning according to special condition, or even clean it everyday; Flow down dust and dirt around the radiator element with 196kPa(2kgf/cm 2 )compression air or even the lower air pressure compression air. If there is still dirt, clean completely with detergent and water; Wear protecting grasses to prevent dust or floating matter hurting your eyes before using compression air; don’t try to clean radiator element with high pressure water tap and high pressure air, or try to clean with brush, which will damage radiator element. 2.3.3 Replace air filter element: Damaged filter element will bring air enter into cylinder without filtering, and accelerates wear of valve, cylinder, piston and piston ring. Dusty air filter element will result in hard starting, power decrease and black smoke of engine.
2.4 Check per 500h operation 2.4.1 Replace fuel filter: Regularly replace diesel filter element before it is blocked by oil mist. (1) Close oil tank switch, disassemble inlet/exhaust pipe, take out diesel filter element, and then clean the fuel filter seat. (2) Replace filter element, install the fuel filter.
![Page 14: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/14.jpg)
(3) Install the fuel inlet/exhaust pipe, turn on oil tank switch, and drain out air in fuel line, otherwise hard starting or stop running after starting will be resulted.
2.4.2 Replace cooling water: Drain out water after the cooling water is cooled down, in order to prevent be scalded by the splashing hot water.
(1) Cooling water which contains iron rust or incrustation will deduce cooling performance, as well as refrigerating fluid.
(2) Cooling water should be replaced at least once per year. Fill in soft water only after draining out the cooling water.
2.4.3 Check and adjust valve clearance Make sure that the valve is off, because only in that condition there will be valve clearance. Notice: This single cylinder/double cylinder engine is marked from flywheel terminal to gearing box terminal, which is different from the normal way. Upper dead point line for each cylinder is marked on the flywheel; you can see them from the dead point view port hole on flywheel cover(φ30). Upper dead point line for single cylinder is marked on engine body.
(1) Adjust valve clearance a) Make sure the 1st cylinder piston is at the compression upper dead point, you can then adjust the inlet/exhaust air clearance of the 1st cylinder 0.1mm;
b) Revolve flywheel 280° in anticlockwise direction after regulation, and adjust the inlet/exhaust air clearance of 2nd cylinder 0.1mm;
Notice: Do remember tighten the adjusting screw cap tightly after regulation, otherwise it will loosen soon and cause engine fail to work.
2.4.4 Check and adjust fuel injector: Check and regulation of fuel injecting pressure and injecting mist quality should be operated on the fuel injecting experiment table.
(1) If the fuel injecting pressure is incorrect, please revolve down the fuel injecting parts fasten cap, take out adjusting gasket and replace for a new one , so that the fuel injecting pressure can attach to the correct valve(13±0.5)MPa.
(2)If the fuel injecting pressure is correct while the quality of injecting mist is poor, please clean the injecting hole or replace the fuel injector parts;
(3)When installing fuel injector into the cylinder cover, please use the original fuel injecting washer to make sure the fuel injecting head extend 2.2-2.3mm. Too big mistake will affect power, fuel consumption or exhaust smoke of diesel engine.
2.5 Check per 1000h operation 2.5.1 Check and adjust the injection advance angle (please leave it to specialist, for this task needs special tools, knowledge and skill).
![Page 15: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/15.jpg)
a. Concrete steps (1) Refill the fuel injection pump with fuel, and revolve the flywheel in clockwise direction to the compression upper dead centre. Resolve the flywheel for several times until there is fuel flowing out. (2) Install the high pressure oil pipe tie which is used for measuring the oil supplying advance angle, then resolve the flywheel to drain out the air inside. Stop the flywheel at 30° BTDC. (3) Resolve the flywheel slowly in clockwise direction and check the oil level, stop the flywheel immediately when oil begins fluctuating. The oil supplying advance angle is supposed to be 18.5°±1°, if not, you should disassemble the fuel injection pump assembly, replace the adjust gasket, check and adjust for another time until the value gets to 18.5°±1°.
(4) Screw on the fuel injection pump fixed bolt after adjusting and install the high pressure oil pipe parts in turn. Notice: Drain out the air in the high pressure oil pipe. The rust and scale in the cooling system will worsen the heat abstraction performance and increase the cooling water temperature. So please clean the rust and scale in the cooling system by professional. 2.6 Check per 2000h running 2.6.1 Check and replace fuel、lube oil、cooling water and rubber hose. Check each kind of rubber hose regularly; replace them if there is damage or aging. 2.6.2 Check and grind sealing ring belt of intake/exhaust valve. Please consult with the specialist because professional skill is needed. You should check the sinking quantity of air door, width of sealing ring belt and clearance between valve stem and valve pipe. 2.6.3 Check performance of fuel injection pump, this job needs oil pump experiment table, so please consult with the specialist to maintain. You should check aiming point oil supply quantity, starting oil quantity, oil supply uniformity of each cylinder, governor, maximum and minimum stable rotation limit.
![Page 16: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/16.jpg)
Disassembly and reassembly of diesel engine 1. Basic procedure of disassembly (1) Prepare necessary room or container to store parts before disassembly, put each kind of bolt and screw as well as related parts together, in order to prevent possible mistaken. (2) Make sure what problem there is before disassembling; avoid mistaken disassembly. 1.1 Disassemble muffler weldment (1) Loosen the four M8 nuts which fix the muffler weldment. (2) Remove the muffler weldment from the cylinder cover. Refer to picture 11
picture 11
1.2 Disassembly the air filter assembly (1) Loosen the two M8 nuts which fix the air filter seat. (2) Loosen the hoop of the connection hose. (3) Remove the air filter assembly. Refer to picture 12
picture 12 1.3 Disassemble the heat abstraction water tank and overflow tank parts (1) Loosen the four M8X10 bolts and nuts which fix the heat abstraction water tank parts (2) Loosen the hoop which fixes the inlet/outlet hose of heat abstraction water tank (3) Remove the heat abstraction water tank parts (4) Remove the overflow tank. Refer to picture 13
![Page 17: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/17.jpg)
picture 13
1.4 Disassemble fan gasket、fan impeller and fan seat (1) Loosen the four M6×25 bolts, which fix fan impeller and fan gasket and then remove the fan impeller and fan gasket. (2) Loosen the three M6×16 bolts which fix fan seat and then remove the fan seat. Refer to picture 14
picture 14 1.5 Disassembly the air conduct cover parts (1) Loosen the three M10X20 bolts which fix the air conduct cover parts on the flywheel end. (2) Loosen the four M6X16 bolts which fix the air conduct cover parts on the engine seat. (3) Remove the air conduct cover parts Refer to picture 15
picture 15 1.6 Disassemble the inlet pressurizer tank (1) Loosen the four M6X18 bolts which fix the inlet pressurizer tank parts on the cylinder cover
![Page 18: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/18.jpg)
inlet flange end. (2) Remove the inlet pressurizer tank parts. Refer to picture 16
picture 16
1.7 Disassemble the water pipe weldment (1) Loosen the M8X10 bolt which fixes the water pipe weldment on the crankcase cover (2) Loosen the hoop which connects the thermostat connection pipe and water outlet pipe. (3) Remove the water outlet pipe weldment. Refer to picture 17
picture 17
1.8 Disassemble the thermostat parts, water outlet pipe seat and water outlet connection pipe. (1) Loosen the two M6X40 bolts which fix the thermostat parts. (2) Loosen the two M6X20 bolts which fix the water outlet pipe seat. (3) Remove the thermostat parts, water outlet pipe seat and water outlet connection pipe. Refer to picture 18
![Page 19: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/19.jpg)
picture 18
1.9 Disassemble the rear support plate parts of starting motor and starting motor parts (1) Loosen the M10X20 bolt which fixes the rear support plate of starting motor on the engine side cover. (2) Loosen the two M10X30 bolts which fix the starting motor parts. (3) Remove the starting motor parts and rear support plate of starting motor. Refer to picture 19
picture 19
1.10 Disassemble the cylinder cover parts (1) Loosen the four M6X25 bolts which fix the cylinder cover. (2) Remove the cylinder cover parts Refer to picture 20
picture 20 1.11 Disassemble the high pressure oil pipe parts and fuel injector assembly (1) Loosen the tie of high pressure oil pipe which connects the fuel injection pump and fuel injector. Remove the high pressure oil pipe parts.
![Page 20: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/20.jpg)
(2) Loosen the fuel injector of the 1st cylinder, take out the fuel injector, two washer and heat insulation sleeve from the cylinder cover. (3) Disassemble the fuel injector of 2nd cylinder in the same way. Refer to picture 21
picture 21
1.12 Disassemble the cylinder cover parts, valve push rod and cylinder cover gasket (1) Loosen the four cylinder cover bolts which fix the cylinder cover parts (2) Remove the cylinder cover parts, two valve push rods and cylinder cover gasket (3) Disassemble the cylinder cover parts in the same way. Refer to picture 22
picture 22 1.13 Disassemble the governor assembly, fuel injection pump assembly and fuel pump tappet. (1) Loosen the seven M6X70 bolts, one M6X85 bolt and four M6X20 bolts which fix the governor assembly. (2) Remove the governor assembly and fuel injection pump assembly. (3) Take out the two fuel pump tappet assembly. (4) Pay attention to the adjusting gasket label in the fuel pump tappet. Make sure the reassembly is correct. Refer to picture 23
![Page 21: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/21.jpg)
picture 23
1.14 Disassemble the flywheel parts and electromagnetic rotor parts (1) Loosen the four M10X32 flywheel bolts which fix the flywheel on the crankshaft. (2) Remove the flywheel parts and electromagnetic rotor parts. Refer to picture 24
picture 24 1.15 Disassemble the stator coil parts (1) Loosen the three M6X25 bolts and one bolt which fix the stator coil parts on the engine rear end. (2) Remove the stator coil parts Refer to picture 25
picture 25 1.16 Disassemble the crankcase cover parts (1) Loosen the seventeen M8X40 bolts which fix the crankcase cover. (2) Remove the crankcase cover parts. Refer to picture 26
![Page 22: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/22.jpg)
picture 26 1.17 Disassemble the camshaft bearing cover and oil supplying camshaft. (1) Loosen the two M6X16 inner hexagonal bolts which fix the camshaft bearing cover (2) Remove the camshaft bearing cover and oil supplying camshaft. (3) Screw on the bearing cover. Refer to picture 27
picture 27
1.18 Disassemble the camshaft and valve tappet (1) Draw out the camshaft parts from the crankcase. (2) Take out the four valve tappets. Refer to picture 28
picture 28
1.19 Disassemble the oil filter baffler weldment and oil filter parts (1) Loosen the two M6X12 bolts which fix the oil filter baffler weldment and remove the oil filter baffler weldment. (2) Loosen the oil filter parts with a special spanner and remove the oil filter parts. Refer to picture 29
![Page 23: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/23.jpg)
picture 29 1.20 Disassemble the piston connection rod assembly (1) Loosen the connection rod bolts of 1st cylinder and 2nd cylinder to remove the connection rod cover. (2) Take out the two piston connection rod assembly. (3) Reassemble the connection rod cover and connection rod bolt immediately after taking out the piston connection rod. (4) Mark the piston connection rod assembly of 1st cylinder and 2nd cylinder. Refer to picture 30
picture 30
1.21 Disassemble the crankshaft parts Draw out the crankshaft parts from the crankcase. Refer to picture 31
picture 31
![Page 24: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/24.jpg)
2. Basic procedure of reassemble Notice items before reassembling (1) Clean thoroughly and check all parts. (2) Lubricate moving parts and revolving parts with fresh oil. (3)Use new gasket、O-style seal ring、oil seal and rubber pipe. (4)Use liquid sealing glue to prevent oil leakage. (5)Make sure clearance between each part (oil film, thrust plate etc) is correct. 2.1 Reassemble crankshaft parts (1)Smear oil on the surface of sliding bearing and crankshaft main journal. (2)Install the crankshaft parts vertically into the sliding bearing hole. 2.2 Reassemble piston connecting rod assembly (1)Smear fresh oil on piston ring、piston pin、cylinder cover and connecting rod big-end hole. (2)The opening of piston ring should be staggered: the 1st ring and the 2nd ring staggered 180°, the 2nd ring and the 3rd ring staggered 100°. Avoid piston main pushing side, lean piston skirt flute on the side of main oil duct. Refer to picture 32
Picture 32
(3)Install disassembled piston connecting rod parts into cylinder cover according to original cylinder number, clamp piston ring with special tools, push piston into cylinder, then close the connecting rod cover. Notice that connecting rod body and bush locating skirt of connecting rod cover should be on the same side, never turnaround.
(4)Smear thread fasten glue on thread of connecting rod bolt, tighten uniformly to stipulate tighten torque for three times (28±2)N·m
(5)Rock connecting rod cover with hands, it should move smoothly and can’t be seized. 2.3 Reassemble the oil filter parts and oil filter baffler weldment (1) Smear fresh oil on the oil filter parts seal ring and screw it on the connection turnbuckle. (2) Screw on the oil filter parts with special spanner (for about 3/4 circuit)
![Page 25: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/25.jpg)
(3) Reassemble the oil filter baffler weldment and fix it with two M6X12 bolts. 2.4 Reassemble valve tappet and camshaft parts (1) Smear little fresh oil on the surface of valve tappet, and install them into the upper valve tappet hole. (2) Smear little fresh oil on the camshaft and install it into the camshaft hole, make sure the joggle label on the camshaft timing gear matches with that of the crankshaft timing gear. (3) Revolve the crankshaft and check the joggle of two timing gears. 2.5 Reassemble the oil supplying camshaft and camshaft bearing cover (1) Smear little fresh oil on the oil supplying camshaft and install it into the camshaft hole. (2) Install the camshaft bearing cover on the bearing seat and fix it with two M6X16 inner hexagonal bolts. 2.6 Reassemble the crankcase cover parts (1) Smear little seal gum on the crankcase cover. (2) Install the crankcase cover and fix it with seventeen M8X40 bolts. 2.7 Reassemble the stator coil parts (1) Install the stator coil parts on the flywheel end. (2) Fix it with three M6X25 bolts. 2.8 Reassemble the oil seal, flywheel and electromagnetic rotor parts (1) Smear little fresh oil on the oil seal lips and install it vertically into the crankcase cover oil seal hole. Pay attention not to roll or lean it. (2) Install the flywheel and electromagnetic rotor parts on the crankshaft flywheel end. (3) Fix the flywheel on the crankshaft end with four M10X32 flywheel bolts. 2.9 Reassemble the fuel pump tappet, governor assembly and fuel injection pump assembly (1) Smear little fresh oil on the two tappets and install them into the tappet hole on the engine top. (2) Smear seal gum on the governor installation face. (3) Fix the governor assembly and fuel injection pump assembly on the engine top with seven M6X70 bolts, one M6X85 bolt and two M6X20 bolts. 2.10 Reassemble the cylinder cover gasket, valve push rod and cylinder cover assembly. (1) Smear little seal gum on both sides of cylinder cover gasket, install it on the engine top. (2) Smear little fresh oil on the valve push rod and Install it the valve tappet hole. (3) Install the 1st cylinder cover assembly on the cylinder cover, screw on the two cylinder cover long bolts and cylinder cover short bolts, the torque is (60±5)N·m. (4) Reassemble the 2nd cylinder cover assembly in the same way. 2.11 Reassemble the fuel injector assembly and high pressure oil pipe parts (1) Install the two fuel injector washers and one fuel injector heat insulation sleeve into the fuel
![Page 26: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/26.jpg)
injector hole and then screw on the fuel injector assembly. The torque is (50±5)N·m. (2) Reassemble the other fuel injector assembly in the same way. (3) Install the high pressure oil pipe parts on the fuel injection pump assembly and fuel injector assembly. Fix them securely. 2.12 Reassemble the cylinder cover parts (1) Install the cylinder coverⅠ, and fix it with four M6X24 bolts. (2) Install the cylinder coverⅡ in the same way. 2.13 Reassemble the support plate parts and starting motor parts (1) Install the rear support plate on the starting motor rear end. (2) Install the starting motor into the motor hole and fix it with two M10X30 bolts. (3) Fix the rear support plate with one M10X20 bolt. 2.14 Reassemble the thermostat parts, water outlet pipe seat and water outlet connection pipe (1) Install the thermostat parts on the water outlet flange face of 1st cylinder cover and fix it with two M6X40 bolts. (2) Install the water outlet pipe seat on the water outlet flange face of 2nd cylinder cover and fix it with two M6X20 bolts. (3) Check the hoop of water outlet connection pipe which connects the thermostat parts and water outlet pipe seat. 2.15 Reassemble the water outlet pipe weldment (1) Fix the water outlet pipe weldment with one M8X10 bolt. (2) Connect the thermostat and water outlet pipe weldment with a hose and lock it with hoop 40. 2.16 Reassemble the inlet pressurizer tank parts (1) Install the 0-seal ring 40X2.65 on the inlet flange groove of pressurizer tank. (2) Install the flange face of inlet pressurizer tank on the cylinder cover inlet port and fix it with two M6X18 bolts. 2.17 Reassemble the air conduct cover parts (1) Install the air conduct cover parts on the flywheel end and fix it with three M10X20 bolts. (2) Fix the air conduct cover seat and engine seat with four M6X18 bolts. 2.18 Reassemble the fan seat, fan gasket and fan impeller (1) Install the fan seat on the flywheel end and fix it with three M6X16 bolts. (2) Fix the fan gasket and fan impeller on the fan seat with four M6X20 bolts. 2.19 Reassemble the heat abstraction tank and overflow tank parts (1) Install the heat abstraction tank and fix it with four M8X110 bolts and nuts. (2) Install the overflow tank. (3) Connect the water inlet port and outlet pipe weldment with a water tank connection hose and lock it with hoop 40.
![Page 27: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/27.jpg)
(4) Connect the water outlet port and water pump inlet port with a water pump inlet hose and lock it with hoop 40. 2.20 Reassemble the air filter assembly (1) Fix the installation seat of air filter with two M8 nuts and washers. (2) Connect the connection hose of pressurizer tank with the inlet port of air filter, and lock it with hoop. 2.21 Reassemble the muffler weldment (1) Install the muffler weldment on the cylinder cover and fix it with four M8 nuts.
![Page 28: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/28.jpg)
Check and maintain 1. Cylinder cover 1.1 Combustion chamber surface of cylinder cover Disassemble fuel injector、inlet valve and exhaust valve, clean the surface of combustion chamber and see whether there is any crack or other damage. Use smear infiltration to check minute crack. 1.2 Inlet/exhaust valve seat (1) Clean cylinder cover、valve and valve sealing cone, insert valve into valve pipe, measure valve sunk mete with deep vernier caliper, refer to picture 33. If the valve sunken mete or valve ring width exceeds much, please adjust it by changing valve or valve seat gasket.
Table 6 Valve sunken mete KM2V80 Model
Item Standard Valve sunken
mete 0.5~0.7
Picture 33 Measure valve sunken mete (2) Check the seal conical surface of inlet/exhaust valve seat and observe the seal ring strip on the valve panel and valve seat ring. 1.3 Inlet/exhaust valve and valve pipe (1) Clean the gathered carton inside valve pipe; measure the valve pipe hole with inside diameter level meter. (2)Check outside diameter of valve rod with outside micrometer. (3)Account the fitting clearance, if it exceeds the limitation valve, please change valve. If it still can’t attach to the limitation valve after changing valve, please change valve pipe. Refer to picture 34.
![Page 29: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/29.jpg)
Picture 34 Check inlet/exhaust valve and valve pipe
Table 7 Fitting clearance between valve pipe and inlet/exhaust valve rod Model Item
KM2V80
Fitting clearance between valve pipe and inlet valve rod
0.03-0.057 (standard)
0.12 (maintenance limitation)
Fitting clearance between valve pipe and exhaust valve rod
0.035-0.062 (standard)
0.12 (maintenance limitation)
1.4 Valve spring (1)Measure the free length of valve spring with vernier caliper, and change the valve spring if the free length exceeds limitation valve. (2)Measure the valve spring verticality; revolve valve spring to see whether the whole side of valve spring is connected with the square ruler. Change valve spring if the measured verticality exceeds the limitation valve. Refer to picture 35 Table 8 Free length and verticality of valve spring
KM2V80 Model
Item Standard Valve spring free
length 39.5
Valve spring verticality
0.5
![Page 30: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/30.jpg)
Picture 35 Measure valve spring
(3)Check whether there is any crack or corrosion on the valve spring surface, if there is any, please change it. 1.5 Lube oil clearance between rockshaft and valve rocker hole Measure the outside diameter of rockshaft with outside micrometer; measure the aperture of valve rockshaft hole with inside lever meter. Then account lube oil clearance, if the measured lube oil clearance exceeds limitation value, please change rockshaft and valve rocker arm. Refer to picture 36 Table 9 Fitting clearance of valve rocker arm hole and rockshaft diameter
KM2V80 Model Item Standard Service
limitationValve rocker arm hole and
rockshaft diameter 0.016~0.045
0.12
Picture 36 Measure lube oil clearance between rockshaft and valve rocker arm hole 1.6 Adjust valve clearance Adjust valve clearance when the generator is at cooling state. Refer to picture 37 Table 10 Clearance of inlet and exhaust valve
KM2V80 Model
Item Standard
Inlet valve clearance 0.10~0.15 Exhaust valve clearance 0.10~0.15
![Page 31: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/31.jpg)
Picture 37 Adjust valve clearance 1.7 Measure cylinder compression clearance height (1)Disassemble cylinder cover, put fuse ф1.5×10mm of the same height on the four points of piston top, reassemble cylinder cover, screw on cylinder cover bolts according to the stipulated order and torque. (2)Revolve crankshaft in anticlockwise direction, flat fuse, disassemble cylinder cover and take out the flat fuse, and measure its thickness. Take the average valve of four fuses as cylinder compression clearance. Refer to picture 38.
Table 11 Piston top clearance KM2V80 Model
Item Standard
Piston top clearance
0.88~1.20
Picture 38 Measure piston top clearance 2 Camshaft parts 2.1 Lube oil clearance of camshaft axial diameter Measure the camshaft journal with outside micrometer, measure inside diameter of camshaft hole with inside diameter lever meter, account the lube oil clearance. If the measured valve exceeds the limitation valve, please change camshaft. Refer to picture 39. Table 12 Fitting clearance between camshaft aperture and camshaft axial diameter
![Page 32: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/32.jpg)
KM2V80 Model
Item Standard Service limitation
Camshaft aperture and camshaft axle diameter
0.032-0.061 0.15
Picture 39 Measure lube oil clearance of camshaft axial diameter 2.2 Height of cam Measure the height of cam at its top point with outside micrometer, if the measured height exceeds the limitation valve, please change for a new camshaft. (Height for inlet/exhaust cam is
31.13+0.03 -0.50 ). Refer to picture 40.
Picture 40 Measure the height of cam
2.3 Lube oil clearance of camshaft axial diameter Measure camshaft journal with outside micrometer, measure inside diameter of camshaft hole with inside diameter lever meter; account the lube oil clearance. If the measured clearance exceeds the limitation valve, please change the camshaft. Refer to picture 41.
![Page 33: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/33.jpg)
Picture 41 Measure fitting clearance of camshaft aperture and axial diameter of oil supplying camshaft
KM2V80 Model Item Standard Service
limitationCamshaft aperture and
axial diameter of oil supplying camshaft
0.032~0.061
0.15
2.4 Valve tappet (1) Check the upper part of tappet. The tappet center line is supposed to be off-centering to the camshaft center, so that to avoid uneven wearing. Change the tappet if it wears severely. (2) Check the tappet surface. Change the tappet if it is damaged or worn. 3. Piston and piston pin 3.1 Piston (1) Check piston top surface, clear up the gathered carton on it, please be careful and don’t hurt the surface. (2) Check piston outside diameter, if damage of piston surface or ring groove exceeds the limitation value, please change for a new piston. (3) Check inside diameter of piston pin hole, if the value of it exceeds the limitation value, please change for a new piston. Refer to picture 42.
Picture 42 Check the inside diameter of piston pin hole
3.2 Piston ring (1) Use special tools to assemble or disassemble piston ring, don’t separate piston ring too hard. (2) Clear up the gathered carton in the ring groove; use thickness gauge or depth gauge to measure the clearance between piston ring and ring groove. If the measured value exceeds the limitation value, please replace piston ring or piston. If the clearance is too big, air leakage will be caused, and then result in leakage of lube oil. Refer to picture 43. Table 14 Clearance between piston ring and ring groove
KM2V80 Model
Item Standard Service
limitationHeight of ring groove and 0.05~ 0.15
![Page 34: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/34.jpg)
thickness of the 1st ring 0.08
Height of ring groove and thickness of the 2nd ring
0.03~0.06
0.15
Height of ring groove and thickness of the 3rd ring
0.02~0.065
0.15
Picture 43 Check clearance between piston ring and ring groove (3) Assemble piston ring to damage parts of cylinder cover, measure piston ring gap clearance with thickness gauge. If the measured value exceeds the limitation value, replace piston ring or cylinder cover. Refer to picture 44
Table 15 Gap clearance of piston ring KM2V80 Model
Item
Standard
Gap clearance of the 1st ring 0.25~0.35Gap clearance of the 2nd ring 0.20~0.35Gap clearance of the 3rd ring 0.15~0.30
Picture 44 Measure the gap clearance of piston ring 3.3 Piston pin Measure the outside diameter of piston pin, if the measured value exceeds the maintenance limitation, or has been grinded severely into echelon form, then you should replace the piston pin. Refer to picture 45. Table 16 Fitting clearance between piston pin hole diameter and piston pin diameter
KM2V80 Model Item Standard Service
limitation
![Page 35: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/35.jpg)
Piston pin hole diameter and piston pin diameter
0.004~0.008
0.025
Picture 45 Measure outside diameter of piston pin and diameter of connection rod bushing hole 3.4 Connecting rod (1) Check parallelism and torsion deformation of connection rod big head and small head. Clamp measurement in the big head hole and small head hole to check the its depth of parallelism and distortional deformation. If the depth of parallelism exceeds promised limitation, please replace connecting rod. Refer to picture 46. Table 17 Parallelism of connection rod big head hole and small head hole
KM2V80 Model Item Standard
Parallelism of connection rod big head and small head
0.04/100
Picture 46 Measure the parallelism of connecting rod big head and small head (2)Check the surface of connecting rod bushing to see whether there is any gaffing、melting or seizure, if there is gaffing or damage , please change the bushing. 3.5 Lube oil clearance between piston pin and connecting rod small head bushing Measure the outside diameter of piston pin which connects with connecting rod bushing with outside micrometer, measure inside diameter of connecting rod small head bushing with inside
![Page 36: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/36.jpg)
diameter lever meter; account the lube oil clearance. If the measured valuve exceeds the limitation value, please replace the piston pin and bushing. Table 18 Fitting clearance between connecting rod bushing hole diameter and piston pin diameter
KM2V80 Model Item Standard Service
limitationConnecting rod bushing hole diameter and piston
pin diameter
0.015~0.031
0.06
4. Crankshaft 4.1 Lube oil clearance of crankshaft、connecting rod big head hole and main bearing hole (1) Painting check of journal neck Clean crankshaft, check whether there is crack by painting infiltrating or magnetic inspection. If there is crack or severe damage, please replace the crankshaft. (2) Measure diameter of crankshaft crank pin (connecting rod journal) with outside micrometer; measure connecting rod big head hole diameter with inside lever meter, then account the lube oil clearance. If the measured value exceeds the limitation value, please replace crankshaft or connecting rod bushing. Refer to picture 47. Table 19 Fitting clearance of connecting rod bushing aperture and crankshaft connecting rod axial diameter.
KM2V80 Model
Item Standard Service
limitationConnecting rod bushing aperture
and crankshaft connecting rod axial diameter
0.025~0.062
0.15
Picture 47 Check the connecting rod axial diameter (3) Check crankshaft main journal diameter with outside micrometer, measure main bearing hole diameter with inside lever meter, then account the lube oil clearance. If the measured value exceeds limitation value, please replace crankshaft or main bushing. Refer to picture 48. Table 20 Fitting clearance of main bearing hole and main axial diameter
KM2V80 Model
Item Standard Service
limitationMain bearing hole and main axial
diameter 0.040~0.071
0.15
![Page 37: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/37.jpg)
Picture 57 Measure main bearing hole and main axial diameter 5. Cylinder block and cylinder cover Measure the inner diameter of cylinder cover. If the measured value exceeds the limitation value, please bore the cylinder again and use the bigger size piston. Refer to picture 49
Table 21 Cylinder cover diameter KM2V80 Model
Item Standard Cylinder cover diameter
80.00~80.03
Picture 49 6. Lubricating system 6.1 Clearance between outer rotor hole and outer rotor Measure the axial diameter of outer rotor with outside micrometer, and measure the oil pump outer rotor hole on the crankcase cover with inner level meter, account the lube oil clearance. If the measured value exceeds the limitation value, please change the oil pump parts. Refer to picture 50.
Table 22 Clearance between outer rotor hole and outer rotor KM2V80
Model Item Standard Maintenance
limitation
![Page 38: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/38.jpg)
Clearance between outer rotor hole and
outer rotor
0.075~0.14 0.20
Picture 50 Clearance between outer rotor hole and outer rotor 6.2 Clearance between rotor pump shaft hold and rotor pump shaft Measure the rotor pump shaft diameter with outside micrometer and measure the rotor pump shaft hole diameter with level meter, account the lube oil clearance. If the measured value exceeds the limitation value, please change the oil pump rotor parts. Refer to picture 51.
Table 23 Clearance between rotor pump shaft hole and rotor pump shaft KM2V80 Model
Item Standard Maintenance limitation
Clearance between rotor pump shaft hole and rotor pump shaft
0.016~0.045 0.10
Picture 51 Measure the clearance between rotor pump shaft hole and rotor pump shaft 6.3 Axial clearance of oil pump (1) Measure the depth of oil pump hole on the crankcase cover with depth meter. (2) Measure the axial thickness of inner/outer rotor with outside micrometer. (3) Account the axial clearance. If the measured value exceeds the limitation value, please change the oil pump rotor parts. Refer to picture 52.
Table 24 Axial clearance of oil pump Model KM2V80
![Page 39: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/39.jpg)
Item Standard Maintenance limitation
Axial clearance of oil pump
0.04~0.10 0.15
Picture 52 Axial clearance of oil pump
7. Cooling system 7.1 Opening temperature of thermostat Add a piece of line between valves of thermostat, put thermostat and a temperature gauge into a barrel. Heat the water in barrel gradually, hold on the line and hang thermostat in air. Thermostat will open as the water temperature increases, please read the temperature. Go on heating, when the thermostat opens for about 6mm, then read again the temperature. If the temperature is not in the leaving factory range, you should replace thermostat. Refer to picture 53.
Table 25 Temperature of thermostat KM2V80 Model
Item Standard Opening temperature
of thermostat 69.5℃~72.5℃
Complete opening temperature of
thermostat
85℃
Picture 53 Measure the temperature of thermostat
![Page 40: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/40.jpg)
7.2 Check water leakage of radiator Fill some water into radiator, install radiator tester, and increase water pressure to 137kPa. Check the water leakage of radiator, if the water leakage is too much, please replace radiator. If the water leak hole is small, please adjust with radiator filling agent. Refer to picture 54.
Picture 54 Check water leakage of radiator
8 Fuel system 8.1 Check fuel injection pressure Install fuel injector on fuel injector tester, remove test handle of fuel injector slowly, and check the instant pressure when fuel is ejected out. If the measured valve is not within the limitation range, please replace fuel injection gasket. 8.2 Check spray of fuel injector Install fuel injector on fuel injector tester, and check the spray of fuel injector. If the quality of spray is not good, please replace fuel injector parts. Refer to picture 55.
Picture 55 Check the spray of fuel injector
8.3 Check the sealing of fuel injector seat Install fuel injector on fuel injector tester, raise the fuel pressure, and keep it at 12.7MPa for 10s. If there is oil leakage, please replace fuel injector parts. Refer to picture 56.
![Page 41: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/41.jpg)
Picture 56 Check the sealing of fuel injector seat
![Page 42: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/42.jpg)
Starting System 1. Starter motor 1.1Check starter motor Refer to Fig 57 (1)Remove the motor excitation & armature winding outlet line from starter motor C wiring terminal (2)Connecting the motor case to battery anode with conducting wire. (3)When connecting the motor case to battery cathode with conducting wire, the motor should revolve, if not, please check the two windings of the motor.
Fig 57
1.2 Check electromagnetic switch Refer to Fig 58 (1)Disassemble the starter motor from the base-frame of starter motor, and prepare a 6V battery. (2)Connect the electromagnetic switch case and C wiring terminal to battery cathode with two conducting wires. (3)Connect the battery anode and receptacle S with another conducting wire, now the gear shaft breaks cover suddenly. If coming away the C wiring terminal, the gear shaft should be on the position protruding, this means the electromagnetic switch is in working order. (4)While testing, please pay special attention that the turn-on time should be only 3 to 5 seconds, if not, the windings will be burnt out.
Fig 58
![Page 43: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/43.jpg)
1.3 Motor disassembly Refer to Fig 59 (1)Disassemble the leading-out wire terminal from the electromagnetic switch wiring terminal. (2)Loose the transfixion screw and the setscrew of carbon brush holder (3)Take off the rear shield, stator, carbon brush holder, and armature in turn. (4)Assembly sequence and disassembly sequence are opposite, smear some lubricant grease on the end B of armature spline while assembling.
Fig 59
1 magnet switch 2.armature 3.leading-out wire terminal of winding 4.stator 5. carbon brush holder 6.rear shield 7.transfixion screw 8. setscrew of carbon brush holder
1.4 Electromagnetic switch dismounting Refer to Fig 60 (1)Loose the three screws of end cover (2)Take off end cover 1 and magnet iron core.
Fig 60
1.5 Decelerating clutch dismounting Refer to Fig 61 (1)Loose three bolts which tighten the driving shell ,(two are outside of motor, one is inside of motor), (2)Take off driving shell, clutch subassembly, steel ball, return spring and drive gear in turn. (3)When assembling, please smear some fresh lube oil.
![Page 44: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/44.jpg)
1. driving shell 2.decelerating clutch 3.steel ball 4. return spring
5. electromagnetic switch 6.driving gear 7.idler gear 8. drive gear Fig 61
1.6 Starter motor inspection and maintenance 1.6.1Commutator inspection and maintenance (1)Check wearing of the commutator, if slightly worn, burnishing and polishing with fine rubber(Refer to Fig 62),
Fig 62 Fig 63 (2)Measure diameter of commutator with outside micrometer, if the measured value is smaller than the limitation size, please change armature. (Refer Fig 63) (3)If there is much difference between excircle wire harness of commutator and axes parallelism, while the minimum size limitation of axial diameter is in the allowable range. Please modify to the specified value on the lathe. Refer to Fig 64 ,
Fig (a) is good, Fig (b) is bad.
Fig 64
1.6.2 Check the electric brush wear Refer to Fig 65
![Page 45: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/45.jpg)
(1)If there is soil and dust on the wearing surface, please burnish with abrasive cloth. (2)Measure the electric brush height with slide gauge. If A is abrasive (means A’s size is smaller), please replace the electric brush.
Fig 65
1.6.3 Check electric brush holder Refer to Fig 66 Check the insulating property between the insulating electric brush holder and supporting plate, if it is current conducting, please replace the electric brush holder.
Fig 66
1.6.4 Check armature Refer to Fig 67 Check the electric conductivity with ohmmeter between the commutator copper sheet and the armature core or armature winding: (1)If the commutator copper sheet and armature core are current conducting, please replace armature. (2)If commutator copper sheet and armature winding are not current conducting, please replace armature.
(3)If the commutator copper sheet is current conducting each other, please replace armature.(Refer to Fig 68)
Fig 67 Fig 68
![Page 46: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/46.jpg)
Engine electrical system 1.6.5 Check stator winding (1) Test electricity of stator winding outgoing line with an ohmmeter, if no conductivity, please replace stator. Refer to Fig. 69 (2) Test insulatibity between stator winding and stator shell with an ohmmeter, if it is conductive, please replace stator. Refer to Fig.70.
Fig. 69 Fig. 70 1.6.6 Check armature roll bearing Small radial and axial clearance, smooth running of roll bearing. If big vibration, clagging or damages happen, please replace the roll bearing. 1.6.7 Check retarder clutch. Refer to Fig.71 (1) Check all gears of retarder clutch, if severe aging or damage happens, please replace retarder clutch or related gear. (2) Check flexibility of retarder clutch. Smooth radial operation and rotation must be secured. No skid when given a force, normal performance maintained, otherwise please replace.
Fig.71 1.6.8 Check electromagnetic switch. Refer to Fig.72 Test electricity conductivity of contact disc in electromagnetic switch. Hold magnetic core with your thumb (Refer to Fig.68), test electricity conductivity between wire holder C and B. If no conductivity, please check contact and fastening between two wire holders and inner copper sheet.
Fig.72
![Page 47: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/47.jpg)
2. Glow plug (1) Check the resistance between center screw and installation thread, resistance of 0.9~1.2Ωindicates good performance of glow plug. Refer to picture 73 (2) Resistance of 0Ωindicates short circuit between center screw and outer shell. Please change the glow plug. (3) If the measured value is not the standard value, please change the glow plug.
Picture 73
![Page 48: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/48.jpg)
Engine Troubleshooting (see Table26~Table33) Table 26 Fault of Alarm System
Table 27 Fault Starting
Fault sympt
om Cause Remedy
Fault Fuel supply system
1.No fuel in fuel tank
2 .Air existed in the fuel supply
system
3 . Electron magnetic stop valve
does not work
4.Unqualified fuel
5.Dirty air filter
6.Low environmental temperature
7.Fuel filter is blocked
8.Incorrect fuel supply timing
9.Blocked nozzle
10. Incorrect air intake and outlet
valve clearance
Add fuel
Eliminate air
Check the function of electron magnetic stop valve
with electricity, then repair or replace
Replace fuel with correct specification
Replace air filter element
Use air heater
Replace fuel filter element
Check and adjust fuel supply advanced angle
Check or replace nozzle
Check and adjust valve clearance
Fault symptom Cause Remedy
Oil Alarm 1.Low oil level
2.Oil filter is blocked
Add oil
Replace oil filter element
Temperature indicator lamp of cooling water
1 .Low cooling water level in
radiator
2.Dirty radiator element
3.Cooling water leak, cooling
water pipe is polluted
4. Fan, Water pump
transmission V belt is loosening.
5.Fault cooling water pump
Add cooling water
Clean radiator element
Check the leakage part of cooling water,
clean or replace cooling water pipe
Tighten or replace
Repair or replace water pump
Charging indicator lamp
1.Fault battery
2.Fault wiring
3.Fault AC alternator
Check electrolyte, and recharge or
replace battery
Check, repair or replace
Repair or replace alternator Low air intake pressure indicator lamp
Dirty air filter element Clean the filter element through
compressive air or replace
![Page 49: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/49.jpg)
11. Poor inside compress of Cylinder
(1)Leakage of air valve
(2)Cylinder, piston, piston rings
are worn out
12.Starting fuel supply is not enough
for fuel pump
Check the cylinder inside compress pressure
standard value 3.1Mpa, with lowest value 2.2Mpa
Check or skive air valve
Repair by professional technician
Check and adjust the fuel pump on the test table
Fault circuit
1. Battery without enough electricity
or loosen connector
2. Starter does not work properly,
only run idle
3. Hard meshing for starter
4.Low running speed of starter
Check the wiring connector or the electrolyte level and
proportion in the battery and recharge the battery
Adjust the joggle position between starter and
flywheel gear ring surface
Battery pressure is heavy in winter or the battery
cable is slightness
Table 28 Abnormal smoke of exhaust air Fault symptom Cause Remedy
Black smoke
1.Overload for diesel engine 2.Blocked air filter 3.Unqualified fuel 4.Large air valve clearance 5.Blocked nozzle or leaked nozzle 6.Incorrect fuel supply timing 7.Air valve without good seal 8. Cylinder, piston, piston rings are worn
Reduce the load Clean or replace air filter element Use fuel with correct specification Check and adjust air valve clearance Check the injected fuel pressure and injected frog quality Check and adjust fuel supply advance angle Check the seal ring, repair and rubbingReplace or repair
![Page 50: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/50.jpg)
Blue smoke
1.High oil level 2.Breather with too much oil frog 3.Ineffective air valve oil seal, large clearance of air valve rod 4.Opposite position of the second ring
Check the oil level in the oil base pan by oil dip stick, and release oil Check seal of the breather valve plate and check if the oil return hole is smooth Replace air valve oil seal or repair air valve and conduit Check and modify (Oil fleecing part is undersurface)
White smoke
1. For it is cold in winter, it is normal to exhaust white smoke at the beginning. As the temperature becomes higher, the white smoke will disappear. 2. The fuel is mixed with water, and there is water steam exhausted 3. The injected fuel is not atomized, and the fuel steam is exhausted. 4. The fuel injection advance angle is too late, the fuel gas is exhausted. 5. There is leakage in cylinder, cylinder head and cylinder gasket.
Drain the water by the fuel drain plug of the fuel tank Check fuel injection pressure and injection frog quality Check and adjust fuel supply advance angle Find the reason that cooling water flow into the cylinder and repair the problem
Table 29 Insufficient Power of Engine
Fault symptom Cause Remedy
Insufficient power of engine
1. Air filter element is too dirty, and the
air intake is not smooth
2. Fuel filter element is too dirty, and
the Fuel supply is unsmooth
3. Fuel pipe is blocked, the fuel supply
is unsmooth.
4. There is leakage of fuel suction pipe
connector, and air goes into the pipe.
5. The timing spring is softening, and
the running speed lower down.
6. The fuel supply limit is too low, no
inefficient fuel volume
7. Fuel supply is not enough in the fuel
pump
8.Fuel supply advance angle is
incorrect
Clean or replace air filter element
Clean or replace fuel filter element
Check and clean or replace fuel pipe
Check the leakage and air exhaust
Check and adjust the running speed of
engine
Make the fuel volume limit larger
Check the fuel supply in the fuel pump
Check and adjust
Check and adjust
![Page 51: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/51.jpg)
9.Fuel injection pressure and injection
frog is unqualified.
10.Incorrect air valve clearance
11.Fuel with poor quality
12. The vent hole on the fuel tank cap
is blocked
13. Insufficient compress pressure in
cylinder
(1)Air valve leak
(2)Cylinder gasket leak
(3)Cylinder, piston, piston ring are
worn and tear
(4)Installation hole of fuel injector
leak
Check and adjust
Use the qualified fuel
Check and dredge
The compress pressure in cylinder
should be around 3.1Mpa
Check, rubbing air valve or replace air
valve, air valve seat ring
Tighten the cylinder head bolt or
replace cylinder gasket
Replace relative parts
Tighten or replace fuel injector washer
Table 30 Unstable operation
Table 31 Overheat of Engine
Fault symptom Cause Remedy
Unstable operation
1. There is air in fuel system
2 . Accelerograph pull rod is not
flexible or the clearance is too large
3.Timing is not flexible
4. The fuel supply of fuel injection
pump to each cylinder is not balanced
5. The injected frog of fuel injector is
in poor quality with fuel drop
Exhaust air, check the leak of fuel
suction pipe connector
Check on the fuel pump test table
Check on the fuel pump test table
Check on the fuel pump test table
Check on the fuel pump test table
Fault symptom Cause Remedy
![Page 52: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/52.jpg)
Table 32 Sudden Stop
High temperature of supplied water
1. Insufficient cooling water in water
tank
2. Air existed in the cooling water
tank
3.Overload of engine
4. Fan belt is loosen to make the
running speed lower
5.Blocked cooling water pipe
6.Too late to inject fuel
7.Combustion is abnormal
8.Dirty water tank surface
9. There is begrime in the cooling
system
10. Damaged thermostat
11.Water pump does not work
properly
12.Water temperature meter does not
work
Add cooling water
Add cooling water or exhaust air
Deduce the load
Tighten or replace the belt
Check or replace
Adjust fuel supply advance angle
Check the injected frog quality
Clean the water tank radiator element
Clean the furring and rust in
professional way
Replace thermostat
Check or replace water pump
Replace
High oil temperature
1.Higher or lower oil level
2.Poor oil quality
3. Air leak in the piston ring
4.High temperature of cooling water
5.Overload of diesel engine
6.Fault water temperature meter
Check the oil level by oil dip stick
Use the oil with correct specification
Check if cylinder, piston ring are worn,
clip and the connecting rod of cylinder
Check as showed above
Deduce the load
Replace
Fault symptom
Cause Remedy
Sudden stop
1. No fuel in the fuel tank
2. There is leak in the fuel pipe, and air
goes into the fuel pipe
3. Blocked fuel filter element
4 .No electricity of fuel pump electron
magnetic stop valve, and cut the fuel
Add fuel
Check the leak, and exhaust air
Replace fuel filter element
Check circuit and electron magnetic stop
valve
![Page 53: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/53.jpg)
Table 33 Abnormal noise in engine while running
supply
5. Fuel pump does not work properly
6. Damaged fuel injection pump
7.No rotation of crankshaft
( 1 ) Broken plain journal bearing of
piston, blocked cylinder
(2)Low oil pressure or broken bearing
and plain journal bearing
(3)Fault oil pump
(4)Air valve head missed, broken piston,
cylinder cover, cylinder head
Replace fuel pump
Replace fuel injection pump
Disassemble and check the engine
Check and repair by professional
technician
Check and repair by professional
technician
Check and repair by professional
technician
Check and repair by professional
technician
Fault symptom
Cause Remedy
Abnormal noise in engine while
running
1. Large air valve clearance, with knock
2.Large clearance between piston and
cylinder, with knock noise
3.Large radial clearance between main
bearing and connecting rod bearing, with
knock noise
4 .Large clearance between piston pin
and head bushing hole of connecting rod
5.Large clearance between piston ring
and ring slot
6 .Large clearance of crankshaft axial
direction, crankshaft is loosen in portrait
direction
7. Air valve touches piston
8 . Large gear clearance, with knock
noise
Check and adjust air valve clearance
Check and replace worn out parts, keep
regular clearance
Check the crankshaft, and replace
bearing
Check and replace connecting rod
bushing and piston pin
Replace piston and piston ring
Replace thrust plate
Check the air valve clearance and valve
timing and cylinder compress
Replace gear
![Page 54: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/54.jpg)
9 . Fuel injection is too early, and the
noise of hitting cylinder
10.Blocked nozzle
Check and adjust fuel supply timing
Clean or replace nozzle
![Page 55: KM2V80 Service Manual](https://reader030.vdocuments.site/reader030/viewer/2022033005/55cf9353550346f57b9d48d8/html5/thumbnails/55.jpg)
Preliminary operation Both new engine and repaired engine have to do preliminary operation. 1.1 Preparing work before starting Check all the bolts and nuts to make sure they are tightened. 1.2 Check and add fuel Check the left fuel level in the fuel tank, and add fuel if necessary. 1.3 Check and add oil Check the oil level in the oil base pan by oil dip stick, and add the same grade oil to the up limit if necessary. Pay attention not to overfill the oil more than up limit. 1.4. Check and add cooling water Check the cooling water level in the radiator and overflow bucket. Add soft water if the cooling water level is too low. Daily check and adding cooling water can only be operated in the overflow bucket. If the cooling water level is lower than the lower limit in the overflow bucket, then check the cooling water in radiator. 1.5 Check the flexibility of governing handle. The governing handle should be flexible and easy to operate. If there is any block, please eliminate the problem. If operate each pivot remotely, please add oil. Please adjust the clearance if it is large. 1.6 Check the alarm system Make sure the alarms of cooling water, oil pressure are in normal condition. It will cause severe result if alarm system does not work properly.