TALL CABINET

To find all Klëarvūe Cabinetry® installation instructions and installation videos, visit www.klearvuecabinetry.com

KIT INCLUDES:

A- Bottom B- Shelf C- Top D- Backers

E- Nailers (H1) Cam Lockx4

(H2) Cam Lock Screwx4

(H3) Dowelx16

(H4) Confirmat Screwx12

Finishing Nailsx24

Cabinet Legsx4

(H6) Glue Bottlex1

STEP 1:• Press cam lock (H1) into shelf (B). A rubber mallet may be used for assistance. • Install cam lock screws (H2) into the tall cabinet side wall using a Phillips head screwdriver. Screws should line

up with the cam lock. Note: Place cam lock screw in the center of the upright for accurate assembly. Once unit is assembled completely, this shelf can be moved to accommodate the configuration. Use 32nd hole for 80” height and 36 hole for 90” height.

• Press shelf onto cam lock screws and secure into place with a quarter turn using a Phillips head screwdriver

Note: Raw end of shelf faces upward. Finish side faces downward towards floor.

STEP 2:• Place glue (H6) into pre-drilled dowel holes of the cabinet side wall (sold separately).• Insert wooden dowels (H3) into glued holes. Note: Roughly half the dowel should fit into the hole. • Apply glue (H6) onto exposed end of inserted wooden dowels (H6).• Connect bottom piece (A) to dowels on cabinet side wall. A rubber mallet may be used to ensure a tight fit.• Secure bottom piece (A) into place using 3 confirmat screws (H4).

(B)

(B)

(A)(A)

STEP 3:• Repeat Step 2 for (C) top piece.• Place glue (H6) into pre-drilled dowel holes of the cabinet side wall (sold separately).• Insert wooden dowels (H3) into glued holes. Note: Roughly half the dowel should fit into hole.• Apply glue (H6) onto exposed end of inserted wooden dowels (H6).• Connect top piece (C) to dowels on cabinet side wall. A rubber mallet may be used to ensure a tight fit.• Secure top piece (C) into place using 3 confirmat screws (H4).

STEP 4:• Place glue (H6) into pre-drilled dowel holes of top piece (C) and bottom piece (A).• Insert wooden dowels (H3) into glued holes. Note: Roughly half the dowel should fit into the hole. • Apply glue (H6) onto exposed end of inserted wooden dowels (H6).• Connect the second side wall (sold separately) to dowels on top piece (C) and bottom piece (A). A rubber mallet

may be used to ensure a tight fit. • Secure the second side wall into place using 3 confirmat screws (H4) on each end.• Repeat step 1 to the second side wall to secure cam lock shelf (B) into place.

Note: Raw end of shelf faces upward. Finish side faces downward towards floor.

(B)

(A)

(C)

(C)

(A)

(C)

(B)

Note: Before moving onto the next step, place a spacer under the cabinet so it will be easier to lift off of the floor.

STEP 5:• Begin to insert back panels. The below solutions are for a full back. If assembling for a built-in appliance, follow

cut outs on page XX.• Slide the two 30”H backers (D) into place on the assembled cabinet first.• Next slide the 19.5”H backer (D).• If you are assembling a 90” tall cabinet, insert the 10”H backer (D) last. If you are assembling an 80” tall cabinet,

you will not need this piece.

STEP 6:• Confirm that the cabinet is square by measuring opposite corner to opposite corner. Adjust as needed.• Place nailers (E) over the seams of the backers (D) and one nailer flush to the top of the cabinet.• Secure nailers (E) with provided finishing nails (H5) using a hammer.

(D)

Note: As you attach nailers, make sure backers (D) are tight against each other to avoid a visible seam inside of the cabinet.

(D)

(D)

(C)

(E)(E)

(E)

(E)(E)

STEP 7:• With two adults, lift the cabinet upright.• While rocking the cabinet toward the front, adjust the 2 back legs. • Once back legs are adjusted, rock the cabinet toward the back and adjust the front legs.• Secure cabinet to wall into stud, through the nailers.

Note: Cabinet legs should be set approximately 4-3/4” from finished floor.

FOR BUILT IN APPLIANCES:• Determine the opening required behind the built in appliance. This information is found in the owners manual of

the appliance. See below for opening sizes per configuration.• When assembling your tall cabinet, you will need to accommodate your backers (D) to account for the opening

required for the appliance.• A reinforced shelf will be required to support the weight of your appliance.• Install fillers and/or trim pieces prior to installing built-in appliance. Note: if appliance has a contoured edge

that would allow for unintentional sight lines into the cabinet, an appliance filler (478-3660) can be installed to conceal view into cabinet. If a gap will appear between the top of your appliance and the bottom of a door, a a drawer from may be cut down and installed as a filler.

1

1

2

3

4

5

5

6

78

9

1110

PICTURED:1. Cabinet side wall2. Top Piece3. Bottom Piece4. Shelf 5. Backer6. Door7. Drawer8. Reinforced shelf9. Filler10. Appliance filler11. Major appliance