keep it clean wiring pro51d
TRANSCRIPT
©2004 The Hoffman Group L.L.C. All rights reserved. KICK/KICKD - 1 of 12 Revised 7/14/04
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
WIRE SYSTEM
WWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
1
2
3
KICK - Standard
ULTRA SMALL 20 PANEL 38 TERMINAL WIRE SYSTEM
KICKD - Deluxe
IMPORTANT: The below instructions are referring to a general installation.
Your vehicle may very from the vehicles described in these instructions use the
diagrams that best describe your vehicle.
ENGINE/FRONTSECTION
DASH SECTION
REAR SECTION
FUSE PANEL
STEERING SECTION
Please read the following instructions carefully.
Reading these instructions before starting this installation, will insure a complete and trouble free installation. These instructions were designed after installing this system in different applications and should make this an easy job for any type of make and model vehicle that you are working on.
To help you with the installation, we have provided basic instructions for Ford, GM and Mopar systems. Please remember that these are basic instructions for your installation. The specific vehicle you're working on may require some modification for your application, depending on what accessories you plan to use. Whenever using after-market equipment or accessories, always use the diagrams provided with that equipment.
When we reference a specific wire, it will be shown with its label then its color. The labeled wire in our instructions will match the label on the wire exactly. If a diagram or picture displays a wire that is not provided in the kit, then you will need to provide that wire. An example of this would be a ground wire. When installing ground wires, make sure the wire is connected directly to a solid chassis ground. We recommend that you use the color black for all ground wires during the installation.
Take good notes.
We have provided plenty of writing space throughout the instructions to make notes during the installation. Taking notes will help you with the install so you don't get lost along the way. In each section of the instructions, you will find a checklist that references the wires to be used. The checklists are labeled "Front", "Rear", "Dash" and "Steering". Here you will write down what wires you will use or not use. If you are using a wire from one section but routing it to a different section, make sure you write down the wire in the new checklist. An example of this could be the fuel pump wire. Go to the "Rear" Checklist, next to the fuel pump wire, write the words, "Front section" in the "Relocate" box. In some cases you might have some wires that you will not be using at all. Place a check mark or an "x" in the "Not Used" column pertaining to the checklist where that wire is located. Keep in mind that it's a good idea to leave this wire in the harness and it should also be routed to the proper location. An example of this would be the cruise control wire, since not all installations will have a cruise control system added to the vehicle. You should still route the wire to where a cruise control module would be installed, just in case a cruise control system is added at a later date. This will give you or your customer future options that can be added to the vehicle when needed.
Preparing the wire harness for installation.
You will need a large area to spread out the harness and prepare for the installation. The floor or a work bench would be a good location to get started. Your new wire harness kit will have four sections, "Front", "Rear", "Dash", "Steering", as described above. Begin with the "Front" section of wires. These are the wires that will be mounted through the fire wall. Unwrap or uncoil the wires and lay them out straight towards the front of the vehicle. The next section of wires will be the "Tail" section. Unwrap or uncoil the wires and lay them out straight towards the rear of the vehicle. The remaining sections of wires are the "Dash" and the "Steering" column sections. The "Steering" column section has the two main connectors that are black and white. The last section is the "Dash" section. Unwrap or uncoil the wires and lay them out straight near the fuse panel.
To insure correct wiring, start by removing all unused wires from the loom and work one section at a time. At this point of the installation it is important to remove each wire, one at a time, by pulling them through the cable ties in the harness.
Once all unused wires are removed from the harness, start to move the noted wires from one section to another by pulling them thought the cable ties and into the desired section. Please take caution to insure you insert the wire into all cable ties throughout the harness sections. Once completed you can now add any additional wires that are not provided in the system. To insure accuracy and easy upgrades, please take notes on any additional circuits that you add.
©2004 The Hoffman Group L.L.C. All rights reserved. KICK/KICKD - 2 of 12 Revised 7/14/04
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
5
4
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
ENGINE/FRONT CHECKLIST
Spec.No. Color
A1
B2
D3
14AWG
8AWG
14AWG
Brown
Red
TanD1 14AWG Blk/Red
H3
H4
H5
H6
16AWG
16AWG
16AWG
14AWG
Drk Blue
Blue/Wht
White
Green
ALT EXC
BATT
CHOKE
TACH
TEMP
REV.SWITCH
HI BEAM
16AWGA4 Lgt Green
RF TURN
FAN PWR
H30 14AWG Green
RELOCATE NOT USED
BlueH7
H8
H10
H11
H12 12AWG Pink
14AWG
12AWG
16AWG
16AWGViolet
Lgt Green
Tan
HORN
H19 16AWG Brown REV.LIGHT
H28 16AWG Blue OIL
COIL
STARTER
F PARK LIGHT
LO BEAM
LF TURN REAR CHECKLIST
ColorNo. Spec.
A8 16AWG Orange
D3 14AWG Brown/Wht
H16 Lgt Green
H19 Brown
H20 Tan
H22 White
H23 Yellow
H24 Green
16AWG
16AWG
16AWG
16AWG
16AWG
16AWG
DOME LIGHT PWR
FUEL PUMP
R PARK LIGHTS
REV.LIGHT
FUEL GAUGE
LR TURN
RR TURN
BRAKE LIGHT
RELOCATE NOT USED
Mounting the fuse panel.
The best place to mount the fuse panel is in a flat dry location away from any heat source near the steering column. It is important to note that you should avoid running or mounting wire away from any moving parts such as: brake pedal, gas pedal, linkage controls, and steering controls. Once mounted, find a location on the firewall and drill a 1 1/4" hole to run all needed wires into the engine compartment of the vehicle.
Routing the wires.
The final step is to clean up your installation by grouping all the wires together and securing them with the cable ties that came in the kit. It is important to take your time and go section by section of your vehicle starting at the tail section and finishing at the dash section.
Engine & Front Section:Start by separating all the engine wires from the other wires in this section. At this point please reference the Front & TRear diagram(pg 5) to finish wiring your lights and accessories. To wire your engine please choose the best diagram that fits your vehicle from the Ford, Mopar, or GM sections. It is important to remember that you must use a fusible link on the red 8 gauge BATT wire. In the event you are using an AMP meter please reference the dash diagram's AMP meter section to insure correct installation.
Rear Section:Run all the wires to the back of the vehicle along your vehicles floor pan into the trunk area avoiding all moving parts. Use tape or cables ties to secure the wires to your vehicle. Once all the wires have been routed to the tail section you will need to hook up all appropriate wires including but not limited to your fuel gauge sender, tail lights, fuel pump, and dome light.
FUSE PANEL
ColorSpec.No. NOT USED
A1A2
A3
A4A5
A6
A7
A8A9
A10
B1B2C1
14AWG
14AWG
14AWG
16AWG
12AWG
Brown
Red/BlueRed/Green
PinkOrange
YellowOrange/Blk
Orange
Green/Red
14AWG
14AWG
16AWG
14AWG
10AWG Orange/Blk
10AWG8AWG
Brown
Red10AWG Orange
ALT EXC
ACC 1
ACC 2
CRUISE/REV
HEATER
WIPER
IGNITION
CIG LIGHTER
DOME LIGHT PWR
KEYLESS
SHAVED DOORS
KEY ACC
BATT
D7
D10
D9
D8
D6
D5
D4
D3
D2
D1 14AWG Blk/Red
Violet
Gray
Blue
Orange
Orange
Orange
Pink
Brown/White
Red16AWG
14AWG
12AWG
12AWG
16AWG
16AWG
16AWG
16AWG
12AWG
FAN PWR
GAUGES
CHOKE/FUEL
PWR WIN
PWR SEAT
RADIO ACC
BRAKE SWITCH
HORN/FLASHER
12V PORT
HEAD LIGHT
©2004 The Hoffman Group L.L.C. All rights reserved. KICK/KICKD - 3 of 12 Revised 7/14/04
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
6
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
DASH CHECKLIST
ColorSpec.No.
A2
A3
A9
14AWG
14AWG
14AWG
Red/BlueRed/Green
Green/Red
A4A5
A6
A7
A7
A8
A10D2
D4
D5
D6
Pink
Orange16AWG
12AWG
14AWG
16AWG
14AWG
16AWG
10AWG
16AWG
12AWG
12AWG
16AWG
Yellow
Orange
Red
Orange/Blk
Orange/Bed
Red
Pink
Orange
Orange
CRUISE
HEATER
WIPER
RADIO BATT
CIG.LIGHTER
UNDER DASH LT
SHAVED DOORS
PWR WINDOW
PWR SEATS
RADIO ACC
GAUGES PWR
ACC 1
ACC 2
KEYLESS
D7D9
H13
H14
H6
H4
H3
H1
14AWG
16AWG
16AWG
Blue/Wht
Green
White16AWG Gray
H18
12AWG
16AWG
16AWG
H20
H21
16AWG
16AWG
16AWG
16AWG
Orange
Gray
Blue
White
Drk BlueTan
Drk Blue
H28 16AWG Blue
BRAKE SW PWR
12V PORT
DASH LIGHTS
TACH
OIL
DIMMER SWITCH
FUEL GAUGE
RF TURN IND.
BRAKE SWITCH
LF TURN IND.
TEMP
HI BEAM
H8 14AWG Tan LO BEAM
RELOCATE NOT USED
STEERING CHECKLIST
Spec.No. Color RELOCATE NOT USED
B1 10AWG Brown
B2 Red
C1 12AWG Orange
12AWG
H5 16AWG Drk Blue16AWG
16AWG
12AWG
12AWG
H7
H10
H11
H12
Blue
Lgt Green
Violet
Pink
DASH LIGHTSGray16AWGH1
COIL
STARTER
F PARK LIGHTS
LF TURN
RF TURN
IGNITION
BATT
KEY ACC
16AWG
16AWG
16AWG
12AWG
H13
H14
H15
H18
H21
H22
H23
H24 16AWG
16AWG
16AWG
16AWGBlack
Blue
White
Drk Blue
Drk Blue
White
Yellow
Green
D10
H16
H2912AWG Blue
16AWG
16AWG
Lgt Green
Drk Blue
LF TURN IND.
BRAKE SWITCH
HORN
DIMMER SW
BRAKE LIGHT
LR TURN
RR TURN
HI BEAM IND.
HEAD LGT PWR
RF TURN IND.
R PARK LIGHTS
Steering Section:The steering column section has all the necessary wires for your vehicles steering column including your ignition switch, turn signals, dimmer switch, and more. Keep It Cleans™ wire panel systems come prewired with two clear and black connectors for a GM steering column with a column mounted ignition switch. These connectors will plug in directly into your column mount ignition switch. In the event you use a different style of switch you may need to rewire the connectors. Please reference your switch diagram(pg 4) to insure correct wiring. Keep It Clean's™ dimmer switch plug will fit GM floor mounted dimmer switches. Please reference the GM wiring section to choose the correct column plug and wire order for your vehicle. All column plug wires are terminated and all plugs are letter coded. Please note that many styles of column connectors and wires have different colors and configurations. If your colors do not match or you are using a switch that is not mentioned then you will need to use a digital volt ohm meter and test for the correct wires. To save time most ignition switch wires are marked on the back. In the event you are using late model GM van column you will need to reference the dash section's ignition switch diagram(pg 4). In most cases late model GM van column turn signals will work correctly on all Keep It Clean™ wire kits. Please test plug for compatibility.
Dash Section:To save time and to insure easy installation start wiring the dash from the drivers side to the passengers side. Please keep in mind that the dash section contains several wires including, but no limited to: heater, headlight switch, gauges, wiper, cooling fan, and more. Once all wires are connected use cable ties to group and secure the wires together. Make sure not to route or secure the wires to any moving parts.
Final Installation:
By this time all wires should be connected or terminated and secured to your vehicle. To start your vehicle for the first time follow these easy steps:
A.Turn off all accessories.B. Close all doors, hood, and trunks.C. Place the ignition switch in the "OFF" position.D. Check to insure there is a fuse on the starter wire.E. Connect the negative battery cable to the battery.F. Check for current draw by connecting one side of a test light to the positive cable, and the other end to the positive side of the battery. If the light goes on you have a either a short or an accessory drawing power. To find the short remove each wire until the light goes out. If you have a dim or no light then it's safe to hook up the positive cable. G. Test the system and all accessories.
©2004 The Hoffman Group L.L.C. All rights reserved. KICK/KICKD - 4 of 12 Revised 7/14/04
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
HEA
DLIG
HT PW
R [b
lue]
DO
ME &
INTER
IOR LG
T RETU
RN
DA
SH LIG
HTS [g
ray]
F PARK
LGTS [lig
ht green]
LATE STY
LE GM
PARK
LGTS
DIM
MER
SW [d
ark
blue ]
R PA
RK
LGTS [lig
ht green]
HI B
EAM
[blue/w
hite]
LO B
EAM
[tan]
KEY
ACC [b
rown]
STARTER
[violet]
COIL [p
ink]
IGN
ITION
[orang
e]
BA
TTERY
[red]
BA
TIGN
ACC
ST
FUEL
METER
TEMP
METER
OIL
METER
VO
LTM
ETER
TACH
OM
ETERSPEED
OM
ETER
LFT TURN IND [blue]
RT TURN IND [dark blue]
GAUGE POWER [red]
FUEL GAUGE [tan]
TEMP GAUGE [green]
TACHOMETER [white]
OIL PRESS. GAUGE [blue]
DASH LIGHTS [gray]
HIGH BEAM IND [dark blue]
DASH S
ECTIO
NUSER GUIDE AND INSTALLATION MANUAL
WWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
©2004 The Hoffman Group L.L.C. All rights reserved. KICK/KICKD - 5 of 12 Revised 7/14/04
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
DOM
E LIGH
T [orange]
REV LIGH
T SW [lgt green]
REV LIGH
T [brown]
BRAKE LIG
HT [w
hite]
FUEL PU
MP [brow
n/white]
R PARK [light green]
LR TURN
[yellow ]
RR TURN
SIGN
AL [green]
DOM
E LIGH
T
THIRD BRA
KE LIGH
T
TRUN
K LIGH
T
FUEL PU
MP
LICENSE PLA
TE LIGH
T
LR PARK
LR BRAKE
REV LIGH
T
REV LIGH
T
LR TURN
RR PARK
RR BRAKE
RR TURN
RR TURN
SIGN
AL [green]
FAN
[black/red]
RF TURN
[dark blue]
LF TURN
[blue]
PARK [light green]
LOW
BEAM
[tan]
HIG
H BEA
M [ blue/w
hite]
HO
RN [green]
HO
RN
LF HEA
DLIGH
T
LF PARK
LF TURN
RF HEA
DLIGH
T
FAN
RF PARK
RF TURN
Rear
Front
FRO
NT &
REA
R D
IAG
RAM
S
NO
TICE: Most early m
odel vehicles brake
and turn
signals are
isolated through the turn signal sw
itch.
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
©2004 The Hoffman Group L.L.C. All rights reserved. KICK/KICKD - 6 of 12 Revised 7/14/04
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
F234A
LT EXCITOR [chocolate]
ALT-STA
RTER [red/wht]
Charg
ing S
yste
ms
EARLY
LATE
HIG
H O
UTP
UT W
IRE
STARTER
+–
GM
SPEC
IFIC D
IAG
RAM
S
COIL PO
S [pink]
TACH
OM
ETER [white]
DIST
COIL
RESISTOR
STARTER
RS
+-
GM
Sta
ndard
Ignitio
n (P
OIN
TS TY
PE)
Engin
e C
onnectio
ns
+–
HEI
OIL SENDING [blue]
COIL POS [pink]TACHOMETER [white]
CHOKE [tan]
TEMP SENDING [green]
STARTER [violet]
STARTER
FRON
T
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
©2004 The Hoffman Group L.L.C. All rights reserved. KICK/KICKD - 7 of 12 Revised 7/14/04
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
MO
PAR S
PEC
IFIC D
IAG
RAM
S 1
OF 2
Charg
ing S
yste
ms
HIG
H O
UTP
UT W
IRE
STARTER
+–
BAT
FLD
FLDIG
N
EARLY
LATE
ALT EXCITO
R [brown]
ALT PO
WER [red]
BAT
FLD
FLD
ELECTRO
NIC
REG
ULA
TOR
ELECTRO
NIC
REG
ULA
TOR
ALTER
NATO
R
ALTER
NATO
R
Mopar Ignition (START/RUN)
IG
BAT
ST SGL
COIL POS [pink]
STARTER [violet]
TACHOMETER [white]
DIST
COIL
RESISTOR
STARTER
SB
+ -
+ –
NEUTRALSAFETY SWITCH
STARTERRELAY
DIODE
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
©2004 The Hoffman Group L.L.C. All rights reserved. KICK/KICKD - 8 of 12 Revised 7/14/04
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
MO
PAR S
PEC
IFIC D
IAG
RAM
S 2
OF 2
Engin
e C
onnectio
ns
IG
BAT
ST SGL
+-
COIL POS [pink]
TACHOMETER [white]
CHOKE [tan]
STARTER [violet]
TEMP SENDING [green]
OIL SENDING [blue]
DIST
NEU
TRAL
SAFETY
SW
ITCH
STA
RTER
RELA
Y
STARTER
SB
+–
COIL
FRON
T
Mopar Ig
nitio
n (ELEC
TRO
NIC
)
IGN
ITION
RESISTOR
DIST
COIL
+-
COIL PO
S [pink]
TACH
OM
ETER [white]
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
©2004 The Hoffman Group L.L.C. All rights reserved. KICK/KICKD - 9 of 12 Revised 7/14/04
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
FORD S
PEC
IFIC D
IAG
RAM
S 1
OF 2
Charg
ing S
yste
ms
ALT EXCITO
R [brown]
ALT-STA
RTER [red/wht]
ALTER
NATO
R
REG
ULA
TOR
STAN
DARD W
IRE
I A S F
S
F BA
T
HIG
H O
UTP
UT W
IRE
STARTER
RELA
Y
ALTER
NATO
R
+
–
STARTER
Ford
Ignitio
n
FROM
NEU
TRAL
SAFETY SW
ITCH
STARTER
RELA
Y
ALTER
NATO
R
+
–
STARTER
SI
COIL PO
S [pink]
TACH
OM
ETER [white]
DIST
COIL
RESISTOR
+-
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
©2004 The Hoffman Group L.L.C. All rights reserved. KICK/KICKD - 10 of 12 Revised 7/14/04
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
FORD S
PEC
IFIC D
IAG
RAM
S 2
OF 2
Ford
Ignitio
n (ELEC
TRO
NIC
) STARTER
RELA
YSI
COIL PO
S [pink]
[white]
[red]
[green][orange][purple][black]
TACH
OM
ETER [white]
DIST
COIL
+-
ELECTRO
NIC
IGN
ITION
MO
DULE
Engin
e C
onnectio
ns
STARTER
RELA
Y
SI
+
–
COIL
+-
DIST
COIL POS [pink]TACHOMETER [white]
CHOKE [tan]
STARTER [violet]
TEMP SENDING [green]
OIL SENDING [blue]
FRON
T
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
©2004 The Hoffman Group L.L.C. All rights reserved. KICK/KICKD - 11 of 12 Revised 7/14/04
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
USER GUIDE AND INSTALLATION MANUALWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
H6
H8
H21
CH
OK
E/FUEL
PUM
P
POW
ER WIN
DO
W
POW
ER SEATS
RAD
IO A
CC
BRA
KE SW
ITCH
POW
ER
HO
RN/FLA
SHER
POW
ER
12V PO
RT
HEA
DLIG
HT
POW
ER
FAN
POW
ER
GA
UG
ES
ALTERN
ATO
REX
CITER
AC
CESSO
RY 1
AC
CESSO
RY 2
CRU
ISE/BA
CK
UP
SWITC
H
HEW
TER/AC
WIPER M
OTO
RPO
WER
CIG
LIGH
TERRA
DIO
BA
TTERY
DO
ME LIG
HT
POW
ER
KEY
LESS ENTRY
SHA
VED
DO
OR
MO
TORS
30A 15A 20A 20A 15A 30A 30A 20A 20A 30A
20A 30A 20A40A 15A20A 30A15A30A20A
WW
W.A
UTO
LOC
.CO
M
Co
lor
H27
No
.
8AW
G
Spec.
Red
H31
8AW
GRed
/Wh
t
BA
TT TO STA
RTER
ALT TO
STARTER
OFF
ON
3020
30 20
2030
30303030
202020
1515
20 20
1515
40
12V
30/
40A
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
B1
B1
B2
B1
C1
B2
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
E1
E2
F1
E2
D8
H30
D8 H15
16AW
GB
r
H26
H25
16AW
GV
Co
lor
D8
No
.
16AW
G
Spec.
VH
ORN
/FLASH
ER
HA
ZA
RD
F1
E2E1
F1D8
F1
H25
B1B
2 H11
H12
B2
C1
DASH S
ECTIO
NColorSp
ec.N
o.
A2
A3
A9
14AW
G
14AW
G
14AW
G
Red/BlueRed/G
reen
Green/Red
A4
A5
A6
A7
A7
A8
A10
D2
D4
D5
D6
Pink
Orange
16AW
G
12AW
G
14AW
G
16AW
G
14AW
G
16AW
G
10AW
G
16AW
G
12AW
G
12AW
G
16AW
G
Yellow
Orange
Re d
Orange/Blk
Orange/Bed
Red
Pink
Orange
Orange
CRU
ISE
HEA
TER
WIPER
RAD
IO BA
TT
CIG
.LIGH
TER
UN
DER D
ASH
LT
SHA
VED D
OO
R S
PWR W
IND
OW
PWR SEA
TS
RAD
IO A
CC
GA
UG
ES PWR
AC
C 1
AC
C 2
KEYLESS
D7
D9
H13
H14
H6
H4
H3
H1
14AW
G
16AW
G
16AW
G
Blue/Wht
Green
White
16AW
GG
ray
H18
12AW
G
16AW
G
16AW
G
H20
H2 1
16AW
G
16AW
G
16AW
G
16AW
G
Orange
Gray
Blue
White
Drk BlueTan
Drk Blue
H28
16AW
GBlue
BRAKE SW
PWR
12V PORT
DA
SH LIG
HTS
TAC
H
OIL
DIM
MER SW
ITCH
FUEL G
AU
GE
RF TURN
IND
.
BRAKE SW
ITCH
LF TURN
IND
.
TEMP
HI BEA
M
H8
14AW
GTan
LO BEA
M
RELO
CATE
NO
T USED
ENG
INE/
FRO
NT S
ECTIO
N
Spec.
No.
Color
A1
B2D3
14AW
G
8AW
G
14AW
G
Brown
Red
TanD
114A
WG
Blk/Red
H3
H4
H5
H6
16AW
G
16AW
G
16AW
G
14AW
G
Drk Blue
Blue/Wht
White
Green
ALT EXC
BATT
CH
OKE
TAC
H
TEMP
REV.SWITC
H
HI BEA
M
16AW
GA
4Lgt G
reen
RF TURN
FAN
PWR
H30
14AW
GG
reen
RELO
CATE
NO
T USED
BlueH
7
H8
H10
H11
H12
12AW
GPink
14AW
G
12AW
G
16AW
G
16AW
GViolet
Lgt Green
Tan
HO
RN
H19
16AW
GBrow
nREV.LIG
HT
H28
16AW
GBlue
OIL
CO
IL
STARTER
F PARK LIG
HT
LO BEA
M
LF TURN
REA
R S
ECTIO
N
ColorN
o.Sp
ec.
A8
16AW
GO
rang
e
D3
14AW
GB
row
n/W
ht
H16
Lgt G
reen
H19
Bro
wn
H20
Tan
H22
Wh
ite
H23
Yello
w
H24
Green
16AW
G
16AW
G
16AW
G
16AW
G
16AW
G
16AW
G
DO
ME LIG
HT PW
R
FUEL PU
MP
R PARK
LIGH
TS
REV.LIG
HT
FUEL G
AU
GE
LR TURN
RR TURN
BRA
KE LIG
HT
RELO
CATE
NO
T USED
Back
Vie
w
Front V
iew
FUSE P
AN
EL
ColorSp
ec.N
o.N
OT U
SED
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
B1B2C1
14AW
G
14AW
G
14AW
G
16AW
G
12AW
G
Brown
Red/BlueRed/G
ree n
PinkO
range
Yello wO
range/Blk
Orange
Green/Red
14AW
G
14AW
G
16AW
G
14AW
G
10AW
GO
range/Bl k
10AW
G8A
WG
Brown
Red10A
WG
Orange
ALT EXC
AC
C 1
AC
C 2
CRU
ISE/REV
HEA
TER
WIPE R
IGN
ITION
CIG
LIGH
TER
DO
ME LIG
HT PW
R
KEYLESS
SHA
VED D
OO
R S
KEY AC
C
BAT T
D7
D10
D9
D8
D6
D5
D4
D3
D2
D1
14AW
GBlk/Re d
Violet
Gray
Blue
Orange
Orange
Orange
Pink
Brown/W
hite
Red16A
WG
14AW
G
12AW
G
12AW
G
16AW
G
16AW
G
16AW
G
16AW
G
12AW
G
FAN
PWR
GA
UG
ES
CH
OKE/FU
EL
PWR W
IN
PWR SEA
T
RAD
IO A
CC
BRAKE SW
ITCH
HO
RN/FLA
SHER
12V PORT
HEA
D LIG
HT
STEER
ING
CHEC
KLIS
T
Spec.
No.
ColorRELO
CATE
NO
T USED
B110A
WG
Brown
B2Red
C1
12AW
GO
range
12AW
G
H5
16AW
GD
rk Blue16A
WG
16AW
G
12AW
G
12AW
G
H7
H10
H11
H12
Blue
Lgt Green
Violet
Pink
DA
SH LIG
HTS
Gray
16AW
GH
1
CO
IL
STARTER
F PARK LIG
HTS
LF TURN
RF TURN
IGN
ITION
BATT
KEY AC
C
16AW
G
16AW
G
16AW
G
12AW
G
H13
H14
H15
H18
H21
H22
H23
H24
16AW
G
16AW
G
16AW
G
16AW
GBlack
Blue
White
Drk Blue
Drk Blue
White
Yellow
Green
D10
H16
H29
12AW
GBlue
16AW
G
16AW
G
Lgt Green
Drk Blue
LF TURN
IND
.
BRAKE SW
ITCH
HO
RN
DIM
MER SW
BRAKE LIG
HT
LR TURN
RR TURN
HI BEA
M IN
D.
HEA
D LG
T PWR
RF TURN
IND
.
R PARK LIG
HTS
©2004 The Hoffman Group L.L.C. All rights reserved. KICK/KICKD - 12 of 12 Revised 7/14/04
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
OPTIONAL ACCESSORIESWWW.KEEPITCLEANWIRING.COMTECH SUPPORT: 503.693.1918
USE THESE EXCELLENT ADD-ON ACCESSORIES TO ENHANCE YOURWIRE PANEL SYSTEM
• SIMPLE INSTALLATION• LONG LIFE AND RELIABLE OPERATION• BACKED BY A LIMITED LIFETIME WARRANTY
IGNITION SWITCH DIMMER SWITCH
BATTERY KILLHEADLIGHT SWITCH
RELAYS
Keep It Clean's headlight switch offersCAD design engerneering that provides smooth operation! Keep It Clean'sunique screw on design offers a cleansmooth look and makes installation asnap
eep It Clean's battery kill switch offersaximum performance and easyperation. The CAD design offers ang life of smooth operation. Backedy a limited lifetime warranty.
Keep It Clean's heavy duty 40-amp relays are the best choice for any type of 12-volt wiring project. The Single pole/Double throw relay will never get stuck or short out on you. Combine our heavy duty relays with our relay sockets, and you've just saved yourself hours of wiring time!
FLEX LOOM
Give your install the ultimate professional appearance. Keep It Clean's Split Loom Tubing keeps all your wires in place and protected from the elements. This product will give any wiring job that final touch.
Keep it Clean's dimmer switch offersCAD design engineering that provides smooth operation! Keep It Clean'sunique floor mounting design offers aclean smooth look and makesinstallation a snap
Keep It Cleans ignition switch offers CAD design engineering that provides smooth operation! Keep It Clean's unique screw on design offers a clean smooth look and makes installation a snap. Each switch comes with 4 heavy duty copper terminals and 4 locking nuts for Ignition, Accessory, Battery, & Starter.