katalog peek tecapeek ensinger
TRANSCRIPT
Semi-Finished Engineering Plastic Products.
TECAPEEK. The high-temperature plasticwith outstanding mechanical properties.
The hydrolysis resistance of TECAPEEKextends to over 200° C. TECAPEEK insulateselectrically even at high voltages.
Electrical engineering and medical technologyas well as mechanical engineering and aerospa-ce benefit from the outstanding load-bearingstrength of TECAPEEK
| Continuous operating temperature up to +260° C and briefly even up to + 300° C
| Outstanding mechanical properties even athigh temperatures
| Outstanding resistance to chemicals
| Hydrolysis resistance even above + 200° C
| Electrically insulating even with high volta-ges
| Excellent sliding properties
| Resistant to high-energy radiation
Gear wheelTECAPEEK:
Torque transmission,high-temperature
application, high sur-face loads.
Cam guideTECAPEEK PVX:
Automation and robo-tics, very good sliding
friction values, highresistance to chemi-
cals.
Transport pinionTECAPEEK MT:
Suitable for use withfoodstuffs, resistant to
sterilisation, dimensional-ly stable.
43
TECAPEEK
Continuous operating temperature
up to + 260° C. Outstanding mecha-
nical properties even at high tempe-
ratures.
TECAPEEK GF 30
Glassfibre-reinforced semi-finished
product with enhanced strength.
Excellent resistance to chemicals.
TECAPEEK CF 30 black
Very high strength values thanks to
the addition of carbon fibres. Enhan-
ced abrasion resistance.
TECAPEEK PVX black
Very good sliding and friction values.
Suitable for bearing parts subject to
high loads.
TECAPEEK MT black
Hydrolysis-resistant, autoclavable semi-
finished product with approvals for
medical technology.
TECAPEEK ELS
defined electrical conductivity, carbon
fibre reinforced providing high strength,
with approvals for use in semi-conductor
technology and the electronics industry.
TECAPEEK HT
very high abrasion and wear resistance,
high load-bearing capacity in static and
dynamic conditions, excellent chemical
resistance.
TECAPEEK TF 10
Very good sliding and friction propertics,
suitable for soft mating partners.
Electrically insulating.
TE
CA
PE
EK
44
TE
CA
PE
EK
*Also available in pigmented form.The specified kg/m weights are purely arithmetic figures.Weight on delivery will deviate from the figures givenabove. Stock lengths 3000 mm, other delivery lengthspossible, also available planed.All figures given without obligation.
= Stock item
= Non-stock item – special production
DIN-Abbreviation
Density (g/cm3)
Diameter
Ø mm
Tolerance TECAPEEK TECAPEEK TECAPEEK TECAPEEK TECAPEEK TECAPEEK TECAPEEK TECAPEEKto DIN GF 30 CF 30 PVX MT ELS TF 10 HTmm black black black* black
PEEK PEEK GF 30 PEEK CF 30 PEEK PEEK PEEK CF PEEK TF 10 PEK
1,32 1,49 1,44 1,48 1,32 1,44 1,35 1,32
kg/m kg/m kg/m kg/m kg/m kg/m kg/m kg/m
5
6
8
9
10
11
12
13
14
15
16
18
19
20
22
25
28
30
32
36
40
45
50
56
60
65
70
80
90
100
110
120
125
135
140
150
165
180
200
Rods
+0,5
+0,1
+0,4 0,029 0,032 0,031 0,032 0,029 0,031 0,029 0,029
+0,1 0,040 0,046 0,044 0,045 0,040 0,044 0,041 0,040
0,071 0,081 0,078 0,080 0,071 0,078 0,073 0,071+0,5
0,090 0,098 0,098 0,090+0,1
0,110 0,124 0,120 0,123 0,110 0,120 0,112 0,11
0,14 0,15 0,151 0,14
0,16 0,18 0,18 0,18 0,16 0,178 0,17 0,16
0,19 0,19
+0,9 0,22 0,22
+0,2 0,25 0,28 0,27 0,28 0,25 0,27 0,26 0,25
0,28 0,32 0,31 0,32 0,28 0,31 0,29 0,28
0,36 0,40 0,39 0,40 0,36 0,39 0,36 0,36
0,40 0,45 0,43 0,44 0,40 0,43 0,40
+1,1 +0,2 0,44 0,50 0,48 0,50 0,44 0,48 0,45 0,44
0,53 0,60 0,58 0,60 0,53 0,58 0,55 0,53
+1,2 0,68 0,77 0,75 0,77 0,68 0,75 0,70 0,68
+0,2 0,85 0,96 0,93 0,96 0,85 0,93 0,87 0,85
0,98 1,10 1,07 1,10 0,98 1,07 1,00 0,98
+1,3 1,11 1,26 1,21 1,25 1,11 1,21 1,14 1,11
+0,2 1,40 1,58 1,53 1,57 1,40 1,53 1,43 1,40
+1,5 +0,2 1,73 1,95 1,89 1,94 1,73 1,89 1,77 1,73
+1,7 2,19 2,39 2,46 2,19 2,39 2,19
+0,3 2,70 3,04 2,94 3,02 2,70 2,94 2,76 2,70
+2,0 +0,3 3,39 3,69 3,80 3,39 3,69 3,39
+2,3 3,90 4,40 4,25 4,37 3,90 4,25 3,98 3,90
+0,3 4,56 5,14 4,66 4,56
+2,5 +0,3 5,29 5,97 5,77 5,93 5,29 5,77 5,41 5,29
+3,0 +0,4 6,92 7,81 7,55 7,76 6,92 7,55 7,08 6,92
+3,4 +0,5 8,77 9,89 9,56 9,83 9,56 8,96 8,77
+3,8 +0,6 10,83 12,22 11,81 12,14 10,83 11,81 11,07 10,83
+4,2 +0,7 13,11 13,11 13,11
+4,6 15,61 15,61 15,61
+0,8 16,91 16,91 16,91
+5,4 19,79 19,79 19,79
+0,9 21,24 21,24
+5,8 +1,0 24,40 24,40 24,40
+6,3 +1,1 29,50
+7,4 +1,2 35,21
+8,5 +1,3 43,53
45
TE
CA
PE
EK
Plates
DIN-Abbreviation
Density (g/cm3)
Size
mm
Tolerance TECAPEEK TECAPEEK TECAPEEK TECAPEEK TECAPEEK TECAPEEK TECAPEEK TECAPEEKto DIN GF 30 CF 30 PVX MT ELS TF 10 HT(mm) black black black* black
PEEK PEEK GF 30 PEEK CF 30 PEEK PEEK PEEK CF PEEK TF 10 PEK
1,32 1,49 1,44 1,48 1,32 1,44 1,35 1,32
kg/m kg/m kg/m kg/m kg/m kg/m kg/m kg/m
*Also available in pigmented form.The specified kg/m weights are purely arithmetic figures.Weight on delivery will deviate from the figures givenabove. Stock lengths 3000 mm, other delivery lengthspossible, also available planed.All figures given without obligation.
= Stock item
= Non-stock item – special production
5 x 300
5 x 500
6 x 300
6 x 500
8 x 300
8 x 500
10 x 300
10 x 500
12 x 300
12 x 500
16 x 300
16 x 500
16 x 1000 **
18 x 500
20 x 300
20 x 500
20 x 1000 **
22 x 500
25 x 300
25 x 500
25 x 1000 **
30 x 300
30 x 500
30 x 1000 **
32 x 500
36 x 500
40 x 300
40 x 500
40 x 1000 **
45 x 500
50 x 300
50 x 500
60 x 300
60 x 500
70 x 300
80 x 300
80 x 500
100 x 300
2,27 2,54 2,27 2,27
+0,7 3,70
+0,2 2,68 3,03 3,01 2,68 2,74 3,70
- 4,38 4,95 4,78 4,92 4,38 4,78 4,48 2,68
3,56 4,01 3,99 3,56 3,64 4,38
+0,9 5,81 6,56 6,34 6,52 5,81 6,34 5,94 3,56
+0,2 4,39 4,95 4,92 4,39 4,49 5,81
7,17 8,10 7,82 8,04 7,17 7,82 7,33 4,39
5,36 6,05 6,01 5,36 5,49 7,17
8,77 9,90 9,57 9,83 8,77 9,57 8,97 5,36
7,03 7,93 7,88 7,03 7,19 8,77
11,49 12,97 12,53 12,88 11,49 12,53 11,75 7,03
22,31
+1,5 12,85 14,50 14,02 14,41 12,85 14,02 13,14 11,49
+0,3 8,69 9,81 9,74 8,69 8,89 12,85
14,21 16,04 15,50 15,93 14,21 15,50 14,53 8,69
27,59
15,57 17,57 16,98 17,45 15,57 16,98 15,92 14,21
10,77 12,16 12,07 10,77 11,01 15,57
17,61 19,87 19,21 19,74 17,61 19,21 18,01 10,77
34,19
13,10 14,78 14,69 13,10 13,40 17,61
21,41 24,17 23,36 24,01 21,41 23,36 21,90 13,10
41,38
22,77 25,71 25,53 22,77 23,29 21,41
25,49 22,77
+2,5 17,26 19,48 18,82 19,35 17,26 18,82 17,65 25,49
+0,5 28,21 31,85 30,78 31,63 28,21 28,85 17,26
54,78
31,61 35,68 35,44 31,61 30,78 32,33 28,21
21,41 24,17 23,36 24,01 21,41 23,36 21,90 31,61
35,01 39,52 38,19 39,25 35,01 38,19 35,81 21,41
+3,525,78 29,10 25,78 26,37 35,01
+0,542,15 47,26 42,15 25,78
29,94 33,79 30,62 42,15
+5,034,41 38,84 35,19
+0,554,62
42,72
46
TE
CA
PE
EK
= Outside
= Inside
The specified kg/m weights are purely arithmetic figures. Weight on delivery will deviate fromthe figures given above. Stock lengths 3000 mm, other delivery lengths possible, also availableground. All figures given without obligation.
= Stock item
= Non-stock item – special production
Tubes TECAPEEK
PEEK
1,32
DIN-Abbreviation
Density (g/cm3)
Tolerance to DINmm
DiameterØ (mm)
-0,3-3,0
-0,3-3,9
-0,3-5,0
-0,5-5,0
40
45
50
56
60
65
70
75
80
85
90
100
110
120
125
130
135
140
150
165
180
200
210
230
250
280
300
360
+2,5
+0,8
+3,6
+1,2
+4,5
+1,5
+5,4
+1,8
+3,0
+0,8
+6,0
+2,0
25 30 36 40 45 50 54 60 70 75
1,17
1,62
2,13 1,85 1,44
2,81 2,53 2,12 1,81
3,31 3,03 2,62 2,31
3,97 3,69 3,28 2,97 2,53
4,73 4,44 4,04 3,73 3,29 2,80
5,50 5,22 4,81 4,50 4,06 3,57 3,14
6,04 5,30 4,98 4,88 4,39 3,96 3,26
5,63 5,32 5,76 5,27 4,84 4,13
6,51 6,19 6,78 6,29 5,16 3,84
7,53 7,22 8,80 8,31 7,88 7,18 5,86 5,12
9,55 9,24 11,03 10,54 10,11 9,40 8,09 7,34
12,97 11,84 10,52 9,78
14,91 14,42 14,00 13,29 11,98 11,23 10,43
15,78 14,64 13,33 12,58
17,18 16,75 16,05 14,74
18,64 18,21 17,51 16,19
21,90 21,47 20,76 19,45
25 30 36 40 45 50 54 60 70 75
47
TE
CA
PE
EK
DiameterØ mm
Tolerance-2,5-8,5
-0,5-8,5
80 90 100 110 125 130 150 175 180 200 290
4,32
6,55 4,79
8,98 7,23 5,27
10,43 8,68 6,72
11,79 10,03 8,07
13,19 11,44 9,48 7,31
14,65 12,90 10,94 8,77
17,91 16,15 14,20 12,03 8,39 7,07 11,78
22,92 21,17 19,21 17,04 13,40 12,08 19,80
28,39 26,64 24,68 22,52 18,88 17,56 24,31
36,42 34,67 32,71 30,54 26,91 25,59 33,60 12,13
37,21 35,05 31,41 30,09 43,71 16,63
46,50 44,34 40,70 60,45 24,1 16,33
56,62 54,45 50,82 72,64 34,22 26,45
50,95 43,18
63,15 55,37
51,67
80 90 100 110 125 130 150 175 180 200 290
40
45
50
56
60
65
70
75
80
85
90
100
110
120
125
130
135
140
150
165
180
200
210
230
250
280
300
360
48
TE
CA
PE
EK = Outside
= Inside
The specified kg/m weights are purely arithmetic figures. Weight on delivery will deviate fromthe figures given above. Stock lengths 3000 mm, other delivery lengths possible, also availableground. All figures given without obligation.
= Stock item
= Non-stock item – special production
Tubes TECAPEEKPVXblack
PEEK
1,48
DIN-Abbreviation
Density (g/cm3)
Tolerance to DINmm
DiameterØ (mm)
-0,3-3,0
-0,3-3,9
-0,3-5,0
-0,5-5,0
-0,5-5,0
40
45
50
56
60
65
70
75
78
80
85
90
100
110
120
125
130
135
140
150
165
180
185
200
210
230
250
+2,5
+0,8
+3,6
+1,2
+4,5
+1,5
+5,4
+1,8
+3,0
+0,8
+6,0
+2,0
25 30 32 36 40 45 50 54 60 70
1,37
1,88
2,45 2,17 1,73
3,22 2,93 2,49
3,77 3,48 3,35 3,05 2,71
4,23 3,79 3,45 3,02
5,07 4,94 4,64 4,3 3,87 3,4
5,8 5,5 5,16 4,73 4,27 3,81
6,05 5,71 5,28 4,81
6,43 6,09 5,66 5,19 4,73 3,97
7,07 6,64 6,17 5,71 4,95
7,78 7,32 6,1 4,67
9,58 9,12 8,37 6,93
12,08 11,62 10,86 9,43
14,81 13,59 12,16
16,44 15,98 15,22 13,79
25 30 32 36 40 45 50 54 60 70
49
TE
CA
PE
EK
DiameterØ (mm)
Tolerance-2,5-8,5
-0,5-5,0
-0,5-5,8
-0,5-5,8
75 80 90 100 110 125 130 150 175 180 200
6,12 5,25
8,62 7,75 5,84
11,35 10,48 8,57 6,51
12,98 12,11 10,2 8,14
14,49 13,62 11,71 9,66
15,2 13,29 11,23 9,2
16,83 14,92 12,87 10,83
20,33 18,41 16,36 14,33 10,39 8,96
22,14 20,1 16,16 14,73
28,28 26,25 22,3 20,88 14,57
16,91
35,44 31,5 30,07 23,77 14,98
34,92 28,62
39,04 28,25 19,67
50,38 39,6 31,02
75 80 90 100 110 125 130 150 175 180 200
40
45
50
56
60
65
70
75
78
80
85
90
100
110
120
125
130
135
140
150
165
180
185
200
210
230
250
75
TE
CH
NIC
AL
DA
TA
TECAN
YL
TECARA
NA
BS
TECAFIN
EPE
TECAFIN
EPP
TECAFO
RMA
D
TECAFO
RMA
H
TECAD
UR
PET, PBT
TECAFIN
EPM
P
TECAN
AT
TECARIM
TECAM
ID11, 12
TECAM
ID46, 66
TECAM
ID6
TECAFLO
NPCTFE
TECAFLO
NPVD
F
TECAFLO
NETFE
TECAFLO
NPTFE
TECASO
NS
TECASO
NP
TECASO
NE
TECATRON
TECAPEI
TECAPEEK
TECAPEEK
HT
SINTIM
ID
VESPEL®
SP1
+ = Resistant (+) = Limited resistance - = Not resistant (also dependent on concentration, time and temperature)
Cupric sulphate 10% + + + + + + + + + + + + - + + + +
Linseed oil + + + + + + + + + + + + + + + + +
Methanol + + + (+) + + + + + + (+) + - + + + + + + (+) +
Methyl ethyl ketone + + + + + - (+) - + + (+) (+) + + + + - (+) + (+) + + + - -
Methylene chloride + - - - + + + (+) (+) (+) - - + - (+) (+) - (+) -
Milk + + + + + + + + + + + + + + + +
Lactic acid, aqueous solution 90% + + (+) + + - - (+) + + - + + - -
Lactic acid, aqueous solution 10% + + + + + + + + + + + + (+) + + + +
Sodium bisulphite, aqueous solution 10% + + + + + + + + + + + + + - - + + +
Sodium carbonate, aqueous solution 10% (+) + + + + + + + + + + + + + (+) + + + +
Sodium chloride, aqueous solution 10% + + + + + + + + + + + + + + + + + + + + + + + +
Sodium nitrate, aqueous solution 10% + + + + + + + + + + + + + +
Sodium thiosulphate 10% + + + + + + + + + + + +
Soda Iye, aqueous 50% - + + - + + + + + + + + - + - + - + + + +
Soda Iye, aqueous 5% (+) + + + + + + + + + + - + + - + + +
Nitrobenzene + - + + (+) (+) (+) - + (+) (+) + + -
Oxalic acid, aqueous solution 10% (+) + + + + + + + + (+) (+) + + + - (+) + + + +
Ozone 2) (+) + + + - - - - - - (+)
Paraffin oil + + + + + + + + + + + + + + + + + +
Perchlorethylene + - - + + (+) (+) - (+) (+) + + - - (+)
Petroleum + + + + + + + - + + + + + (+) +
Phenol, aqueous solution + + + + + - - - - + - - - + + (+)
Phosphoric acid, concentrated (+) + + + + + + + - - - - + + + +
Phosphoric acid, aqueous solution 10% - (+) + + + + + - - - - + + (+) - + +
Propanol + + + + + - + + + + + + + +
Pyridine - - - + + + + + + - (+) + (+) (+) (+) -
Pyridine 3 solution, aqueous solution + + + + - + -
Salicylc acid + + + + + + + + (+) +
Nitric acid, aqueous solution 2% + + + - + + + + + + + + - - - - - + + - - + + + -
Hydrochloric acid, aqueous solution 36% - + + + + (+) + + + - - - - + + - - - + + + +
Hydrochloric acid, aqueous solution 2% + + + + + + + + + + + - - (+) + + + - - + + + +
Sulphur dioxide + (+) + + + + + + - + + + + (+) -
Sulphuric acid, concentrated 98% - - - - - - + + (+) + - - - - - + - - - + (+) - -
Sulphuric acid, aqueous solution 2% + + + + + + + + + + + + - - - + + - + - + + + +
Hydrogen sulphide, saturated + + + + + + + (+) + - + + - +
Soap solution, aqueous solution - (+) + + + + + + + + + + + + + + +
Silicone oils + + + + + + + + + + + + + + + + +
Soda solution, aqueous solution 10% (+) + + + + + + + + + + + +
Edible fats, Edible oils + + + + + + + + + + + + + +
Styrene + + + + + + - + (+) (+) -
Tar + + + + + (+) (+) (+) + +
Carbon tetrachloride + + (+) + + + + + - + - + + (+) - - - -
Tetrahydrofurane + + + - + + + + + + + - - - (+) - (+) (+) -
Tetralin + + + + + - + + + - (+) -
Ink + + + + + + + + + + + +
Toluene + + + + (+) - (+) - + + + (+) + + + + - - (+) + + + (+) -
Transformer oil + + + + + + + + + + + (+) + + + (+) + +
Triethanolamine - + + + + + - + - + + +
Trichlorethylene + + + - - + + - (+) (+) (+) - - - - - (+) - - -
Trilon B, aqueous solution 10% + + + + +
Vaseline + + + + + + + + + + + + + + + (+) +
Wax, molten + + + + + + + + + + + + + + + + (+) (+) +
Water, cold + + + + + + + + + + + + + + + + + + + + + + + + +
Water, warm - + + - (+) (+) (+) + + + (+) (+) (+) (+) (+) + - (+) - + + + +
Hydrogen peroxide, aqueous solution 30% - (+) (+) + (+) + + + + - - - - + + - - + + +
Hydrogen peroxide, aqueous solution 0,5% + + + + + + + - - - - + + + (+) + + + +
Wine, Brandy + + + + + + + + + + + + + + + +
Tartaric acid + + + + + + + + + + (+) (+) + + + +
Xylene + + + + + (+) + - + + (+) + + (+) - - (+) + + - - - -
Zink chloride, aqueous solution 10% + + + + + + + + + + (+) (+) (+) + + - + + + +
TE
CH
NIC
AL
DA
TA
76
ENSINGER High-temperature plastics.Material standard values.
The information corresponds with current knowledge, and indicates our pro-ducts and possible applications. We cannot give you a legally binding guaran-tee of the physical properties or the suitability for a specific application. Existing commercial patents are to be taken into account. A definite qualityguarantee is given in our general conditions of sale.
Tests are carried out in a standard atmosphere of 23° C 50 RH according to DIN50 014.We reserve the right to make technical alterations.
SINTIMIDPI black 300 1,34 116 9 4000 4000 75 12 0,8
SINTIMID
PUR HT PUR HT
SINTIMIDPI CS 15 15% graphite, black 300 1,42 97 2,8 4000 4000 88(d) 26(i) 0,27
SINTIMID
15G 15G
SINTIMIDPI CS 40 40% graphite, black 300 1,57 65 2,2 80(d)
SINTIMID
40G 40G
SINTIMIDPI CS 15 TF 10
15% graphite, 10%300 1,48 77 2,9 85(d)
SINTIMID
PVX PTFE, black PVX
SINTIMIDPI PTFE 30 30% PTFE 260 1,51 82 4,1 84(d)
SINTIMID
30P 30P
SINTIMIDPTFE + PI Polyimid P84, brown 260 1,85 15 200 65(d)
SINTIMID
8000 8000
TECAPEEKPEK 260 1,3 2110 20 3800 4100 108(r) .
TECAPEEK
HT HT
TECAPEEK PEEK also in black** 260 1,32 95 25 3000 4100 M99 o. Br. 0,30-0,38 TECAPEEK
TECAPEEKPEEK GF 30 30% glass fibre 260 1,49 180 2,5 9500 10000 M103 60 36 0,38-0,46
TECAPEEK
GF 30 GF 30
TECAPEEKPEEK CF 30
30% carbon fibre,260 1,40 215 1,5 18500 20000 255 35
TECAPEEK
CF 30 black CF 30
TECAPEEKPEEK
10% carbon fibre,260 1,48 130 1,5 9500 8100 208 30 0,11
TECAPEEK
PVX PTFE, graphite, black PVX
TECAPEEKPEEK coloured 260 1,32 95 20 3000 4100 M99(r) o. Br. 0,30-0,38
TECAPEEK
MT MT
TECAPEEKPEEK black 260 1,32 95 20 3000 4100 M99(r) o. Br. 0,30-0,38
TECAPEEK
MT sw MT sw
TECAPEEKPEEK CF carbon fibre, black 260 1,44 175 1 15500 M105 30
TECAPEEK
ELS ELS
TECAPEEKPEEK TF 10 PTFE 260 1,35 80 15 3000 n. b.
TECAPEEK
TF 10 TF 10
TECAFLONPTFE 260 2,18 25 > 50 700 30 o. Br. 5 1,58 0,08-0,10 21
TECAFLON
PTFE PTFE
TECATRON PPS 230 1,35 75 4 3700 3600 190 50 TECATRON
TECATRONPPS black 230 1,35 75 4 3700 3600 190 50
TECATRON
MT sw MT sw
TECATRONPPS GF 40 40% glass fibre 230 1,65 185 1,9 14000 13000 320 45
TECATRON
GF 40 GF 40
TECATRONPPS
10% carbon fibre,230 1,54 115 1,5 10000 203 20 0,21 0,69
TECATRON
PVX PTFE, graphite, black PVX
TECASONPES translucent 180 1,37 90 40 2700 148 o. Br. 20
TECASON
E E
TECASONPPSU black 170 1,29 70 > 50 2350 2600 31 o.Br.(k)
TECASON
P P
TECASONPPSU black 170 1,29 70 > 50 2350 2600 31 o. Br.
TECASON
P MT sw P MT sw
TECAPEI PEI translucent 170 1,27 105 > 50 3200 3300 140 4 TECAPEI
TECAPEIPEI GF 30 30% glass fibre 170 1,51 165 2 9500 9000 165 40
TECAPEI
GF 30 GF 30
TECAPEIPEI coloured 170 1,27 105 3200 3300 140 4
TECAPEI
MT MT
TECASONPSU translucent 160 1,24 80 > 50 2600 147 o. Br. 42 22 0,4
TECASON
S S
TECAFLONE/TFE 150 1,73 45 40 800 60(d) o. Br. 0,4
TECAFLON
ETFE ETFE
TECAFLONPVDF 150 1,77 50 > 30 2000 2000 80 o. Br. 34 3 0,3
TECAFLON
PVDF PVDF
TECAFLONPVDF CF 8
8% carbon fibre,150 1,78 93 1 6000 6000 0,23
TECAFLON
PVDF CF 8 black PVDF CF 8
Servicetemperature°C long term
Works-nomenclature
Works-nomenclature
DIN-abbreviation
additivesand/orcolour
Mechanical properties
Den
sity
(ASTM
D 7
92, D
IN 5
3 47
9)
Tensi
le s
tren
gth a
t yi
eld
(ASTM
D 6
38, D
IN E
N IS
O 5
27)
Tensi
le s
tren
gth a
t bre
ak (A
STM
D 6
38,
DIN
EN
ISO
527
, ASTM
D 1
708
(a))
Elongat
ion a
t bre
ak (A
STM
D 6
38,
DIN
EN
ISO
527
, ASTM
D 1
708
(a))
Modulu
s of e
last
icity
afte
r te
nsile
tes
t
(ASTM
D 6
38, D
IN E
N IS
O 5
27)
Modulu
s of e
last
icity
afte
r fle
xura
l tes
t
(ASTM
D 7
90, D
IN E
N IS
O 1
78)
Cre
ep ruptu
re s
tren
gth a
fter
100
0 h
with s
tatic
load
Tim
e yi
eld li
mit fo
r 1%
elongat
ion a
fter
100
0 h
Coef
ficie
nt of f
rict
ion p
= 0
,05N
/mm
2 v =
0,6
m/s
on s
teel
, har
dend a
nd gro
und
Wea
r
(condit
ions
as p
revi
ous)
«1/1000MPa
Har
dness
(bal
l inden
tation: I
SO
203
9/1,
Shore
D: A
STM
D 2
240,
DIN
53
505
(d),
Rock
wel
l: ASTM
D 7
85 ,
ISO
203
9/2
(r),
other
s: A
STM
D 7
85 (a
), DIN
43
456
(s))
Impac
t re
sist
ance
(DIN
EN
ISO
179
, Izo
d: ASTM
D 2
56,
DIN
EN
ISO
180
(i),
Char
py: D
IN E
N IS
O 1
79 2
1 ,
notch im
pact st
rength
: DIN
53
456
(k))
«B/1000MPa
ankJ/m2
HKMPa
EBMPa
EZMPa
µ–
V
µ/km
ßR%
«RMPa
«SMPa
ªg/cm3
TE
CH
NIC
AL
DA
TA
77
Works-nomenclature
Works-nomenclature
Thermal properties Electrical properties** Miscellaneous data
Mel
ting p
oint
(DIN
53
736)
Gla
ss tra
nsition t
emper
ature
(DIN
53
736)
Hea
t dis
tort
ion t
emper
ature
after
ISO
-R 7
5, m
ethod A
(DIN
53
461)
Hea
t dis
tort
ion t
emper
ature
after
ISO
-R 7
5, m
ethod B
(DIN
53
461)
Max
imum
ser
vice
tem
perat
ure s
hort ter
m
Therm
al c
onductiv
ity
(23°
C)
Spec
ific
heat
(23°
C)
Coef
ficie
nt of l
inea
r th
erm
al e
xpan
sion
(23°
C, A
STM
D 6
96, D
IN 5
3 75
2, A
STM
E 8
31)
Die
lect
ric
const
ant (1
06 H
z,
ASTM
D 1
50, D
IN 5
3 48
3, IE
-250
)
Die
lect
ric
loss
fact
or (1
06 H
z,
ASTM
D 1
50, D
IN 5
3 48
3, IE
-250
)
Volu
me
resi
stan
ce
(ASTM
D 2
57, E
C 9
3, D
IN IE
C 6
0093
)
Surf
ace
resi
stan
ce
(ASTM
D 2
57, E
C 9
3, D
IN IE
C 6
0093
)
Die
lect
ric
stre
ngth (A
STM
D 1
49,
IEC-2
43, V
DE 0
303
part 2)
Res
ista
nce to t
rack
ing (D
IN 5
3 48
0,
VDE 0
303
part 1)
Mois
ture
abso
rption t
o equili
brium
23 °C/5
0% rel
ativ
e hum
idity
(DIN
EN
ISO
62)
Wat
er a
bsorp
tion a
t sa
tura
tion
(DIN
EN
ISO
62)
Res
ista
nce to h
ot w
ater
,
was
hing s
oda
Flam
mab
ility
acc
. to U
L
stan
dard 9
4
Res
ista
nce
to w
eath
erin
g**
Tm°C
Tg°C
HDT/A
°C
HDT/B
°C °C
¦W/(K·m)
c
J/(g·K)
|10-5 1/K
RON
ßr–
tan –
ªDN · cm
EdkV/mm
Grade – – –W(H2O)
%
WS%
For VESPEL® see page 54.
Test specimen to DIN 53 455
** For materials where also in black is detailed under "additives and/orcolour” the electrical values do not apply to the black type.Additionally, the black variants are resistant to weathering.
+ = Resistant (+) = Limited resistance – = Not resistant(depending on concentration, time and temperature)
These values represents the average of a number of individual measurements.Unless otherwise stated the test results apply to injection moulded samples.
SINTIMID360-375 368 350 0,22 1,04 4,9 3,1 0,003 1017 1015 20 2,6 3,6 (+) V0 (+)
SINTIMID
PUR HT PUR HT
SINTIMID330 300 350 0,53 1,13 3,8 107 2,3 (+) V0 +
SINTIMID
15G 15G
SINTIMID330 350 3,1 V0
SINTIMID
40G 40G
SINTIMID330 350 2,5 4x1011
SINTIMID
PVX PVX
SINTIMID330 350 5 V0
SINTIMID
30P 30P
SINTIMID327 -20 327 0,25 1 2,3 1018
SINTIMID
8000 8000
TECAPEEK374 157 165 5,7 3,3 0,0035 1016 V0 -
TECAPEEK
HT HT
TECAPEEK 343 143 140 182 300 0,25 0,32 5,0 3,2-3,30,001-
1016 1015 20 0,1 0,5 + V0 - TECAPEEK0,004
TECAPEEK343 143 315 300 0,43 2,0 0,004 7x105 3x106 24,5 0,1 0,1 + V0 -
TECAPEEK
GF 30 GF 30
TECAPEEK343 143 315 300 0,92 1,5 1015 1015 0,1 0,1 + V0 +
TECAPEEK
CF 30 CF 30
TECAPEEK343 143 277 300 0,24 2,2 3x105 5x106 0,1 0,1 + V0 +
TECAPEEK
PVX PVX
TECAPEEK343 143 140 182 300 0,25 0,32 5,0 3,2-3,3
0,001-1016 1015 20 0,1 0,5 + V0 -
TECAPEEK
MT 0,004 MT
TECAPEEK343 143 140 182 300 0,25 0,32 5,0 3,2-3,3
0,001-3x105 5x106 20 0,1 0,5 + V0 -
TECAPEEK
MT sw 0,004 MT sw
TECAPEEK343 143 300 0,29 1,5 103 102 0,1 0,2 + V0 -
TECAPEEK
ELS ELS
TECAPEEK300 143 300 0,1 + V0 -
TECAPEEK
TF 10 TF 10
TECAFLON327 -20 55 121 260 0,25 1 12 2,1 0,0002 1016 1016 48
KA 3c< 0,05 + V0 +
TECAFLON
PTFE KB>600 PTFE
TECATRON 280 90 110 260 0,25 5 1013 1015 0,01 + V0 - TECATRON
TECATRON280 90 110 260 0,25 5 1013 1015 0,01 + V0 +
TECATRON
MT sw MT sw
TECATRON280 90 260 260 0,25 1,18 ca. 3 4 0,004 1013 1015 20 KC 175 0,02 1 + V0 -
TECATRON
GF 40 GF 40
TECATRON280 90 260 3-4 4x105 1x106 0,02 + V0 +
TECATRON
PVX PVX
TECASON225 204 214 220 0,18 1,12 5,5 3,5 0,005 1016 1014 40 0,7 2,1 + V0 -
TECASON
E E
TECASON220 207 214 190 0,35 5,6 3,45 1015 1013 15 0,37 1,1 + V0 -
TECASON
P P
TECASON220 207 214 190 0,35 5,6 3,45 1015 1015 15 0,37 1,1 + V0 -
TECASON
P MT sw P MT sw
TECAPEI 217 180 200 200 0,22 5 3,15 0,001 1015 1015 33 0,27 1,25 + V0 - TECAPEI
TECAPEI217 210 215 200 0,23 2 3,7 0,007 1015 1015 30 0,5 0,9 + V0 -
TECAPEI
GF 30 GF 30
TECAPEI217 180 200 200 0,22 5 3,15 0,001 1015 1015 33 0,7 1,25 + V0 -
TECAPEI
MT MT
TECASON188 180 169 181 180 0,25 1 5,5 3,1 0,005 1016 1014 42
KA1KB 0,2 0,8 + V0 -
TECASON
S 175 S
TECAFLON267 -100 71 105 150 0,24 0,9 13 2,6 0,001 >1016 > 1016 <0,05 0,03 + V0 +
TECAFLON
ETFE ETFE
TECAFLON172 -18 95 140 150 0,11 1,2 13 8 0,06 1014 1013 17*/150 KA 1 <0,05 <0,05 + V0 +
TECAFLON
PVDF PVDF
TECAFLON172 -18 150 3,6 0,04 + V0 +
TECAFLON
PVDF CF 8 PVDF CF 8