JCB WHEEL LOADER | 406

A

B

C

D

E

F

STATIC DIMENSIONS

ft-in (mm)

A Overall Length with Standard Bucket 16-10 (5133)

B Wheel Base 6-11 (2100)

C Min Ground Clearance 1-1 (330)

D Height Over Cab 8-2 (2500)

E Max Bucket Width 6-3 (1900)

F Wheel Track 4-7 (1390)

Front Axle Weight* lb (kg) 3161 (1434)

Rear Axle Weight* lb (kg) 7716 (3500)

Operating Weight (includes standard bucket) lb (kg) 10,877 (4934)

Inside Radius ft-in (mm) 6-7 (2010)

Maximum Radius Over Standard Bucket ft-in (mm) 15-8 (4160)

Maximum Radius Over Tires ft-in (mm) 12-6 (3800)

Articulation Angle degrees ±40°

Max Width Across Tires ft-in (mm) 5-9 (1761)

Note: Dimensions assume fitment of standard JCB 12.5x18 wheel and tires. *Axle weights based on unloaded bucket in carry position.

1.0yd3 (0.8m3) bucket

MAX ENGINE POWER: 62 hp (46kW) MAX OPERATING WEIGHT: 11,204 lb (5,082 kg) MAX LOADER CAPACITY: 1.8 yd3 (1.4 m3)

JCB WHEEL LOADER | 406

ENGINE

Type Hydrostatic

Make Rexroth

Model A6VM

Low Range mph (km/h) 3.8 (6)

High Range mph (km/h) 12.5 (20)

TRANSMISSION

Type Straight Beam

Make Dana Spicer

Model 111

Overall Axle Ratio / Drop Box Ratio 19.3 / 2.1

Chassis Angle Oscillation degrees ±10°

AXLES

Pump Type Gear

Pump Max Flow gal/min (l/min) 16 (60)

Pump Max Pressure psi (bar) 3335 (230)

Hydraulic Cycle Times at Full Engine Revs: Seconds

Arms Raise (full bucket) 4.9

Bucket Dump (full bucket) 3.5

Arms Lower (empty bucket) 3.1

Total Cycle 11.5

Max Auxiliary Flow gal/min (l/min) 16 (60)

LOADER HYDRAULICS

gal (liters)

Hydraulic and Transmission System 18.5 (70)

Fuel Tank 21 (80)

Engine Oil Sump 3.1 (12)

Axle Oil (front) Including Hubs 1.16 (4.4)

Axle Oil (rear) Including Hubs and Drop Box 1.6 (6.05)

SERVICE FILL CAPACITIES

System Voltage V 12

Alternator Output Ah 80

Battery Capacity Ah 105

Cold Cranking Capacity CCA 870

ELECTRICAL SYSTEM

Loader: Parallel lift geometry; Quickhitch with hydraulic pin locking.

Engine: 4 cylinder oil cooled diesel engine; dual stage cyclonic engine air filter; Single bowl fuel filter; Fan guards.

Transmission: Two position electric switch; Neutral start; Disconnect on footbrake (inching capability).

Axles: Straight beam axles.

Brakes: In board oil immersed brakes with combined handbrake.

Electrical: Road lights front and rear; Reverse lights; 80 amp alternator; battery isolator switch.

Hydraulics: Gear pump with priority steer; Emergency steer back up; 3 spool loader circuit.

Cab: ROPS/FOPS safety structure; Fully adjustable seat; Interior light; Safety glass; Electronic monitoring with warning panel; Front and rear screen wash/wipe; 3 speed heater fan with replaceable filters; LH opening door; Up and over handbrake with catch; Laminated screen; Loader control isolator; Door lock back system; Storage tray.

Bodywork: Front and rear fenders; Side and rear access panels; Fixed bottom steps; Full width rear counterweight; Recovery hitch; Lifting lugs; Engine sump kit, 12.5 R18 JCB tires.

STANDARD EQUIPMENT

Limited slip differential axles front/rear; 3 HBCV; Epoxy coated cooling pack; Smooth ride system; Air suspension seat; Creep speed; 4th spool auxiliary circuit; High spec cab; Front and rear working lights; Fire extinguisher; Face level fan; Radio installation kit; Reverse alarm; Rotating beacon; Adjustable steering column analogue gauges; Reversing lights and rear fog lights; Sun visor; Biodegradable oil; Sliding window; 407/409 adapter plate; Single level joystick control; Foward/reverse switch on joystick control lever, air conditioning, canopy.

OPTIONAL EQUIPMENT

12.5/80 R18 SGL, 335/80 R18 XM27, 335/80 R18 XZSL.

TIRES

Type 4 Cylinder Diesel

Make Deutz

Model D2011 L04i

Capacity in3 (l) 220.9 (3.62)

Bore in (mm) 3.7 (96)

Stroke in (mm) 4.9 (125)

Aspiration Naturally Aspirated

Cylinders 4

Power Rating

Gross Power to SAE J1995/ISO 14396 hp (kW) @ 2500 rpm 62 (46)

Net Power to J1349/EEC 80/1269 hp (kW) @ 2500 rpm 58 (43.5)

Torque Rating

Gross Torque lbf ft (Nm) @ 1700 rpm 140 (190)

Emission Certification EPA T3 (EU Stg 3)

JCB WHEEL LOADER | 406

LOADER DIMENSIONS PALLET FORK DIMENSIONS

Loader Dimensions: Assumes Fitment of 12.5x18 Tires.

ft-in (mm)

Fork Carriage Width 4-5 (1345)

Length of Tines 3-11 (1200)

AF Reach at Ground Level 2-4 (710)

BF Max Reach Arms Horizontal 4-1 (1232)

CF Below Ground Level 0-3 (84)

DF Height Arms Horizontal 4-8 (1426)

EF Max Height 9-11 (3012)

FF Reach at Max Height 1-8 (506)

Full Turn Tipping Load (500 mm load centers) lb (kg) 5688 (2580)

Operating Load (60%) lb (kg) 3412 (1548)

Operating Load (80%) lb (kg) 4550 (2064)

PALLET FORK DIMENSIONS

L

K JH

G

O

P

NM

R

S

AB

C

D

E

EF

DF

CF

AF

BF

FF

LOADER DIMENSIONS

Bucket General General Light Light 6-in-1 Clam

Purpose Purpose Duty Duty Shovel

Capacity Heaped yd3 (m3) 1.0 (0.8) 1.3 (1.0) 1.6 (1.2) 1.8 (1.4) 1.0 (0.75)

Material Density lb/yd3 (kg/m3) 3400 (2050) 2688 (1620) 2190 (1320) 1858 (1120) 3484 (2100)

Empty Bucket Weight lb (kg) 633 (287) 710 (322) 778 (353) 846 (384) 959 (435)

Bucket Equipment Teeth or Teeth or Teeth or Teeth or Teeth or

Toeplate Toeplate Toeplate Toeplate Toeplate

Static Tipping Load, Straight (EN) lb (kg) 9458 (4290) 9268 (4212) 9079 (4118) 8986 (4076) 9028 (4095)

Static Tipping Load, Full Turn 40° (ISO) lb (kg) 7275 (3300) 7143 (3240) 6984 (3168) 6914 (3136) 6945 (3150)

Payload 50% lb (kg) 3638 (1650) 3571 (1620) 3492 (1584) 3456 (1568) 3472 (1575)

Max Tearout Force lbf (kN) 9420 (41.9) 8205 (36.5) 7238 (32.2) 6676 (29.7) 9420 (41.9)

Bucket Width ft-in (mm) 6-3 (1900) 6-3 (1900) 6-3 (1900) 6-3 (1900) 6-3 (1900)

Outside Turning Circle Radius ft-in (mm) 13-8 (4160) 13-9 (4185) 13-10 (4210) 13-10 (4229) 13-8 (4160)

A Total Length (bucket flat on ground) ft-in (mm) 16-10 (5133) 17-2 (5233) 17-9 (5333) 18-9 (5408) 16-10 (5133)

L Lift Height Max ft-in (mm) 13-7 (4140) 13-1 (4246) 14-6 (4333) 14-7 (4438) 13-8 (4157)

E Digging Depth ft-in (mm) 0-4 (105) 0-4 (105) 0-4 (105) 0-4 (105) 0-4 (105)

H Dump Height ft-in (mm) 8-2 (2489) 7-11 (2418) 7-8 (2348) 7-6 (2295) 8-2 (2489)

M Reach at Max Height @ 45° Dump ft-in (mm) 2-6 (764) 2-9 (835) 3-0 (905) 3-2 (958.5) 2-6 (764)

N Max Reach @ 45° Dump ft-in (mm) 4-11 (1494) 4-10 (1465) 5-2 (1635) 5-6 (1689) 4-11 (1494)

Operating Weight lb (kg) 10,870 (4934) 10,950 (4969) 11,020 (5000) 11,090 (5031) 11,200 (5082)

B Length to Loader Pin ft-in (mm) 14-4 (4369)

C Wheel Base ft-in (mm) 6-11 (2100)

D Minimum Ground Clearance ft-in (mm) 1-1 (330)

F Height Over Cab ft-in (mm) 8-2 (2500)

J Load Over Height ft-in (mm) 8-10 (2991)

K Hinge Pin Height ft-in (mm) 10-3 (3131)

O Roll Back at Full Height degrees 56°

P Dump at Full Height degrees 45°

R Rollback at Carry degrees 54°

S Dump at Minimum Height degrees 67°

LOADER DIMENSIONS

JCB WHEEL LOADER | 406

JCB Headquarters Savannah, 2000 Bamford Blvd, Savannah, GA 31322 Tel: (912) 447-2000 Fax: (912) 447-2299 www.jcb.com

JCB reserves the right to change design, materials and/or specifications without notice. Specifications are applicable to units sold in the United States and Canada. The JCB logo is a registered trademark of J C Bamford Excavators Ltd.

A GLOBAL COMMITMENT TO QUALITY

JCB’s total commitment to its products and customers has helped it grow from a one-man

business into one of the world’s largest manufacturers of backhoe loaders, crawler

excavators, wheeled excavators, telescopic handlers, wheeled loaders, dump trucks,

rough terrain fork lifts, industrial fork lifts, mini/midi excavators, skid steer loaders and tractors.

By making constant and massive investments in the latest production technology, the

JCB factories have become some of the most advanced in the world.

By leading the field in innovative research and design, extensive testing and stringent quality control,

JCB machines have become renowned all over the world for performance, value and reliability.

And with an extensive dealer sales and service network in over 150 countries,

we aim to deliver the best customer support in the industry.

Through setting the standards by which others are judged, JCB has

become one of the world’s most impressive success stories.

DWUSA 2979 12/11