issue 18 | 2020 health & safety news...hazards and the steps you can take to protect yourself....
TRANSCRIPT
Every day workers are
potentially exposed to
common and sometimes
unusual inhalation hazards.
At Roux, typical job sites
present airborne dust and
carbon monoxide hazards,
which can be monitored
and controlled efficiently.
However, certain projects can pose unique threats such as
airborne PCB dust particulates, silica dust, asbestos, mercury
vapors, and various volatile organic compounds (VOCs). It is
essential to understand both the dangers presented by these
hazards and the steps you can take to protect yourself.
· Air Monitoring – Use properly calibrated equipment
(e.g. dust meter, photoionization meter, multi-gas
meter) to monitor your work environment for dust,
VOCs, and other possibly harmful gases/vapors.
Silica dust can be a common airborne contaminant if not
properly controlled at the source. Typically, airborne silica is
present due to cutting, grinding, drilling, or disturbing
materials which contain crystalline silica such as concrete.
Silicosis is a common disease associated with silica dust
inhalation, and as a result causes the build-up of scar tissue
in the lungs from acute or chronic exposure to dust
containing silica. Silicosis can cause bronchitis-like
symptoms, difficulty breathing, chronic phlegm production,
and attribute to the development of cardiovascular
diseases.
Remember, PPE is a workers' last line of defense, it is
preferred proper engineering and administrative controls be
instituted prior to PPE implementation. Respiratory protection
should be instituted when airborne hazards cannot be
removed from the work environment. Depending on the
nature and severity of the hazard, half-face and full-face
respirators are commonly used to defend against airborne
contaminants. In particularly hazardous environments such
as those immediately dangerous to life and health or when
contaminants are unknown, SCBAs are required as they
supply a fresh source of breathable oxygen, instead of just
filtering out contaminants from the work atmosphere. As
always, you should consult with someone within your
organization who has proper PPE/respiration knowledge in
order to identify the correct respirator to protect yourself in
your unique environment. Remember, those who are required
to wear respiratory protection need to be medically cleared, fit
tested, and properly trained prior to using respiratory
protection.
How to Protect Yourself
Luckily, there are plentiful methods and options to protect
yourself from inhalation hazards.
· Respirator/Self Contained Breathing Apparatus
(SCBA) – Respirators and SCBAs can be used in
order to prevent inhalation; however, airborne
contaminants should be known. This is to ensure
proper selection of cartridges and changeout
schedules for filters in the case of air-purifying
respirators.
Dangers of Inhalation
We commonly deal with VOC contamination at sites, often
VOCs associated with petroleum hydrocarbons. Acute
VOC inhalation can cause shortness of breath, dizziness,
fatigue, and nose/lung irritation. Long-term exposure or
exposure to high concentrations can lead to various
cancers of the liver and kidneys, and can cause damage to
the central nervous system.The most important part of inhalation safety is to always be
mindful of the work taking place around you and the
different hazards that can be created. Stay vigilant, don't
get complacent, and be aware of the serious long-term
complications associated with potential inhalation
exposures.
· Air Filtration/Purification – Air purification systems
can be set up in your work environment to filter out
certain compounds, such as dust and other
construction debris. Filtration systems with
appropriate filters can also reduce potential VOCs
in air, as appropriate.
Another dust inhalation related condition, asbestosis, is a
chronic lung disease caused by long-term inhalation of
asbestos fibers, typically the result of construction/demolition
activities. Symptoms of asbestosis are similar to silicosis, but
long-term inhalation of asbestos can lead to mesothelioma,
an aggressive cancer that affects the lining of the lungs.
· Dust Prevention – Use wet methods during dust-
generating work activities. Water the site, if
necessary, to prevent airborne dust from becoming
an issue in the first place.
Safety Tips for
Wetland
Delineations
Page 2
Understanding Inhalation Hazards and
How to Protect Yourself
www.rouxinc.com
ISSUE 18 | 2020
Health & Safety
News
1
By Patrick – New York RubenbauerPage 3 Dermal
Exposure in
the Workplace
Drilling
Safety
Page 4-5
www.rouxinc.com 2
Safety Tips for Wetland Delineations By Kristy Northrup – Logan Township, New Jersey
Biological and Weather-Related Hazards
Common Wetland Hazards
Wetland delinea�ons are conducted by specialists usually trained in biology and/or soil science. Depending on the loca�on of the site, wetland scien�sts follow one of two main procedures for delinea�ng wetlands. Both methods use a three criteria approach, where the wetland scien�st must evaluate the plants, soil, and hydrology to characterize the land as being either a wetland or an upland.
Thick vegeta�on also brings the risk of branches scratching or poking the field delineator in the eyes, so safety glasses must always be worn. If you can picture yourself in the middle of the woods for a delinea�on, do you think you have all your PPE? Gloves? Boots? Backpack for supplies? Safety glasses? You're off to a great start, but you may s�ll need a few more things...
Wetlands OverviewAs a subset of our Brownfields Prac�ce Area, some of our clients come to us when they suspect that wetlands might be on their property. Typically, our clients are trying to redevelop the land and they need to know if and where wetlands might be located before they start to build. We are also u�lized internally for remedia�on projects where wetlands were iden�fied during the receptor evalua�on. Whether you have impacted wetlands on or adjacent to your site could influence your remedial inves�ga�on (and poten�al ecological assessment). It is therefore cri�cal to have confidence in the exact loca�on of your wetland boundaries. While publicly available maps give us an ini�al idea of where wetlands might exist, nothing beats the “boots on the ground” approach to flagging the wetlands in situ.
Unfortunately, the plants in your wetland can be a biological hazard as well. Poison ivy is a faculta�ve species in many regions of the United States. That means that it can grow and thrive in both wetland and upland condi�ons. Wetland scien�st should be familiar with poison ivy (three almond-shaped leaves that range in color) and take precau�ons to avoid contact with the plant's oils. One easy trick is to wear long sleeves, even in the middle of the summer, or pack a Tyvek in your car just in case.
Last but not least, weather condi�ons should be kept in mind for scheduling wetland delinea�ons. As with all other sites, thunder and lightning can put a damper on the field work progress. Many wetland delinea�ons take place in the middle of a forest and it can be challenging to reach a safe place quickly. Furthermore, these events require the use of a hand auger to advance soil borings. The last thing you want to do is find yourself in the middle of a wetland with a metal auger in one hand when lightning strikes. Plan accordingly to avoid stormy field days.
In terms of temperature, it is common for our wetland delinea�ons to occur during the hot summer months. Wetland delineators should come prepared with plenty of water to drink (poten�ally in a backpack water bladder) and should take frequent breaks to avoid heat exhaus�on and overexer�on. Remember that if you're the only person at a site, you cannot rely on someone else to call for help. Instead, rest when necessary to maintain a healthy pace.
More o�en than not, the wetland scien�st must traipse through wooded areas with tree roots, branches, low lying shrubbery, thorns, and other t r i p p i n g h a za rd s . C u t- re s i s ta nt g l o ve s a re recommended for moving branches out of the walkway, but some�mes the best solu�on is to pick a different path through the woods. Inspec�ng the ground first before stepping one way or another can make all the difference in arriving at your des�na�on safely. Addi�onally, ponded water can make for a muddy and slippery mess. It is impera�ve to take slow, deliberate steps and to avoid carrying more equipment than necessary. Field supplies should be stored in a backpack while walking around the site; this
will keep items from catching on branches or vines and will keep hands free for balance and support.
Obviously, wetland delinea�ons require us to be out in the field. Whether it's at a peat bog or a salt marsh, the promise of a seasonally high water table means bugs galore. Insect repellent that contains DEET should be applied every few hours, and if there are known or suspected �cks at the site, it would be wise to treat your clothes with permethrin the day before your site visit. Regardless of how o�en or what kind of repellent is used, �ck checks should be conducted thoroughly during the field event, especially before ge�ng back into your vehicle, and once again when you get home.
When we are sent to a site to conduct a wetland delinea�on, the environmental quality of the site may be poor due to exis�ng site development and poten�al contamina�on. This can pose a risk to the wetland scien�st who needs to collect soil borings for evalua�on. At select loca�ons throughout the site, an open-faced auger is used to extract a soil core and then texture is assessed by feel. In accordance with the job loss analysis (JLA) form, the most appropriate personal protec�ve equipment (PPE) should be worn at all �mes to minimize skin contact with poten�al contaminants in the soil. If the delineator needs to wade through shallow water, muck boots or waders are also required to prevent contact with the water.
Recognizing Contact Derma��s
In my case, the concentrated cleaning product created a drama�c concentra�on gradient when it met my skin, allowing for rapid diffusion. In many cases, skin
absorp�on has been the primary source of internalized doses of polycyclic aroma�c hydrocarbons (PAHs). Mercury and polychlorinated biphenyls (PCBs) can also be readily absorbed, and precau�ons should be taken when working with these chemicals.
· Another skin-harming force is the sun. Alwaysprotect your skin with a high SPF sunscreenand light layers.
· Shower and wash hands thoroughly a�er beingin the field and protect your hands withp e t r o l e u m j e l l y,lo�on, or cream.
Chemical Absorp�on
Skin Hazards
· Communicate withyour office Healthand Safety Manager ifyou no�ce any skinirrita�on or changesin skin condi�on.
Protec�ve Measures
When I was 15, I worked at a busy childcare center. At the end of the evening, a�er the last child was picked up by their parents, the staff would get to cleaning. One night, while dilu�ng a concentrated cleaning solu�on, I spilled a bit onto my hand. I washed it off quickly, thinking nothing of it. However, a week later I found myself combing the internet to iden�fy what was happening to my skin. I didn't even make the connec�on that it was from the chemical exposure at work. My lack of knowledge about the chemicals we used and a lack of training on how to protect myself contributed to an easily avoidable workplace dermal exposure injury.
Chemicals can migrate from the surface of the skin into the body without entering through a break in the skin. This process is called dermal absorp�on and it is controlled by diffusion. When a chemical is present on the outer layer of skin, it creates a concentra�on gradient between the outer and inner layer, which ini�ates mass transfer across the cell membranes. In this way, the concentra�on of the chemical that comes in contact with skin is the key factor in determining the rate of absorp�on.
Contact derma��s cons�tutes 90-95% of all OSD in the United States, therefore it is important to understand the signs and symptoms. It is defined as inflamma�on of the skin resul�ng from contact with a hazardous agent. Symptoms include swelling, itchiness, dry skin that may develop cracks, pain, redness, and the development of small blisters with a white center. Contact derma��s can be triggered by an irritant source or by an allergic reac�on that was triggered by dermal contact. At-home treatments include moisturizing, applying a cool wet compress, and taking an an�histamine such as Benadryl to help reduce itching. If home treatments do not ease symptoms, doctors can prescribe steroid creams and oral medica�ons.
Unfortunately, these types of injuries are common: 3.4 skin-related injuries are reported to the Bureau of Labor per every 10,000 employees yearly, compared to 1.9 respiratory illnesses per 10,000 employees. Occupa�onal skin diseases (OSD) are the second most common type of occupa�onal diseases. OSDs include irritant contact derma��s, allergic contact derma��s, skin infec�ons, skin injuries, skin cancers, and other skin diseases.
OSDs can be caused by chemical, physical, and biological agents, and by mechanical trauma. Chemical agents are the most common and can be divided into two subcategories: sensi�zers and primary irritants. Repeated exposure from sensi�zers can cause an allergic reac�on, while primary irritants cause a direct chemical reac�on with the skin.
· Have an OSHA-required safety data sheet (SDS)for each known chemical you may be workingwith on the jobsite. These include informa�onabout risks for skin irrita�on, cancer, andallergies.
· Always wear appropriate PPE, which mayinclude gloves, aprons, hats, or masks. Nitrilegloves are useful in protec�ng againstchemicals and infec�ous agents. Nitrile glovesshould be layered under cut-resistant gloves.
Physical agents include extreme temperature condi�ons or radia�on exposure. Biological agents include plants, animals, and microorganisms. Parasites, insect bites, and poison oak and ivy are considered biological agents of OSD. Mechanical trauma can occur through abrasions, cuts, and lacera�ons, and even pressure or fric�on. Cut-resistant gloves are necessary for many tasks on the worksite and help prevent mechanical trauma.
· Do not eat, drink, or smoke in your work area.This can introduce addi�onal pathways forchemicals to enter the body.
To avoid dermal chemical exposure, employ these protec�ve measures on the job:
· Don't bring contamina�on home with you.Dispose of used nitrile gloves into a trash bagseparate from field supplies and properly cleanyour boots, clothes, and backpack.
www.rouxinc.com 3
Dermal Exposure in the Workplace: How to Protect Yourself By Lauren Mitchell – Oakland, California
Drill Rig Hazards
Pre-drilling Safety
In addi�on to these shared hazards, there are drill rig-specific hazards, which may vary depending on the rig and type of drilling method (e.g., direct push, air/mud rotary, sonic, hollow stem). A common misconcep�on is that the larger the machinery, the more dangerous it will be. However, a smaller rig like a direct push Geoprobe can s�ll be just as dangerous as a larger truck-mounted air rotary rig. Larger equipment used by subcontractors, like truck-mounted sonic drill rigs, are among the safest of the drilling methods Roux personnel encounter due to minimal physical contact with drilling equipment and the encapsula�on of drilling materials within the drill rod. (Cont. on Page 5)
While physical hazards (i.e. line of fire, rota�ng augers) associated with drill rigs may seem like the most dangerous aspects during drilling, the first few feet of your drill hole can pose a significant risk from both a personal injury as well as to poten�al infrastructure. Taking the ini�al steps to preclear a proposed drilling loca�on will go a long way in preven�ng poten�al contact with subsurface u�li�es.
The process of preclearing the proposed drill loca�on serves as a precau�on to poten�al hazards that may arise from the physical subsurface. This provides visual confirma�on of the subsurface through the use of hand tools (e.g. hand auger), a pressurized air knife, or vacuum. These tools are much less aggressive than a drill rig boring through the ground, allowing for careful visual inspec�ons of the subsurface.
There are various types of drill rigs, all of which can pose significant physical hazards. Common hazards that are consistent amongst all types of drill rigs are: pinch points, pressurized hydraulic lines, and overhead booms under stress. The material (e.g., soil) being drilled into is also a common hazard, notably if the material is contaminated. Regardless of size/power generated by the drill rig, it is always important to work to eliminate poten�al contact hazards by keeping a safe distance away from equipment and any moving pieces. For all drill rigs, it is important to properly inspect the equipment prior to beginning work—especially inspec�ng all emergency stop bu�ons. If any part of the equipment is not func�oning properly, work should not begin un�l the equipment has been repaired appropriately.
Drilling ac�vi�es account for some of the most hazardous tasks we oversee at Roux. Being in close proximity to large machinery with moving components requires spa�al awareness and alertness in order to minimize poten�al losses. For Roux, it starts with preplanning work ac�vi�es and requirements which aid in mi�ga�ng poten�al hazards in the field. This can include, but is not limited to, public/private u�lity mark outs; establishment of preclearing requirements/protocol; development of heavy equipment exclusion zones, as well as outlining specific personal protec�ve equipment (PPE) which can vary depending on the work environment; contaminants of concern; and more. Addi�onally, various drilling methods can pose equipment-specific hazards which need to be considered when developing the overall scope of work and development of an equipment-specific job hazard analysis. Proper pre-planning allows for both Roux and its contractors to be aligned when it comes to implemen�ng an effec�ve health and safety plan.
Preclearing prior to drilling can help iden�fy u�lity lines that were missed by public mark outs or private geophysical inves�ga�ons. This greatly reduces the risk of damaging gas, water, electric, or fiberop�c u�li�es.
While not included in a public/private u�lity mark out, iden�fying overhead u�li�es is s�ll necessary prior to subsurface drilling ac�vi�es to ensure the drill rig has a sufficient and safe amount of space to drill.
While preclearing your drill loca�on, always make sure to wear appropriate PPE outlined within a job hazard analysis. As men�oned above, understanding what exists in the first few feet of the subsurface and the u�li�es that may reside in this zone prior to drilling, isessen�al to mi�ga�ng poten�al hazards such as u�litystrikes.
www.rouxinc.com 4
Drilling Safety By Dan Heilemann – Logan Township, New Jersey
Best prac�ces advise that exclusion zones should be set
at greater than the swing/�p radius of the specific
heavy equipment. This is to keep unnecessary
personnel outside of the work zone from wandering
too close to the drill rig and to provide a safe distance
from the drill rig in case failure occurs. Roux's standard
prac�ce is to set an exclusion zone at least 15 feet
around the drill rig or greater than the swing/�p/reach
radius of any moving part on heavy equipment. This is
done in order to eliminate the poten�al for line of fire,
contact, and other unique hazards which heavy
equipment may pose. Use of effec�ve barriers will aid
in preven�ng unauthorized personnel from ge�ng too
close to the opera�ng machinery. Addi�onally, no one,
including authorized operators, should be within 3 feet
of the opera�ng equipment (e.g. rota�ng augers) as
pressurized drilling rods and hydraulics could cause
bodily harm while in use. Exclusion zones serve as a
barrier between outside forces and the work being
performed at hand to minimize the poten�al for a
significant loss.
Hollow Stem Auger Drilling
Exclusion Zones
Hollow stem auger drilling uses either a track-mounted
Geoprobe® or a slightly larger truck mounted auger
and boom. This is typically the smallest of the drilling
rigs Roux personnel encounter, but this also means it is
the most “hands on” rig used by subcontractors. Since
the drilling equipment is so small, it requires
subcontractors to manually and physically move auger
heads constantly on and off the rigs in order to drill
downhole. Due to this direct interac�on with the
equipment, pinch points and drilling contaminants are
of par�cular concern with this drilling technique.
A truck-mounted air rotary uses compressed air to help
the drill bit advance downward. In order to keep the
borehole clean and accessible for the drill bit,
compressed air is periodically blown down the hole by
the operator to clear out unnecessary debris. This
means dirt, dust, mud, or water can be expelled from
the drill hole at high pressures, leading to airborne
debris. Depending on the consistency of the debris and
proximity to the borehole, addi�onal engineering
controls or PPE, such as dusk masks or Tyvek suits may
be required.
Mud Rotary DrillingSimilar PPE from that of air rotary drilling may also be
required for truck-mounted mud rotary rigs, which
circulates drilling fluid down the borehole and back
into a slurry tank next to the rig. Mud slurry collected
from downhole may splash as it is being brought up
from the borehole, which is why it is important to
always remain a safe distance from the borehole, away
from the drillers opera�ng the machinery.
Air Rotary Drilling
Nevertheless, it is s�ll important to be mindful of
poten�al hazards. Below are some of the method-
specific hazards for each drilling type.
Sonic DrillingSonic drill rigs use sonic vibra�ons and differing
frequencies to penetrate the subsurface. The drilling is
performed by going through the center of a steel casing
that is a�ached to the rig. This keeps all the drilling
material encapsulated within the system, preven�ng
material from spraying out from the drill hole. While
sonic drilling is a large piece of equipment that requires
proper exclusion zones, the hazards associated with
drilling ac�vi�es are generally safer than comparable
drilling methods.
www.rouxinc.com 5
Drilling Safety (Continued By Dan Heilemann – Logan Township, New Jersey