ip-10 quick startup guide

FibeAir® IP-10 Quick Startup Guide

Aug 2008

IP-10 Quick Startup Guide Doc Rev0.1 2

PROPRIETARY

Contents 1. DOCUMENT PURPOSE ............................................................................................................... 3

2. DOCUMENT SCOPE .................................................................................................................... 3

3. STARTUP CONFIGURATION STEPS ....................................................................................... 3 3.1. LAUNCHING WEB-MANAGEMENT ............................................................................................ 4 3.2. IDU SOFTWARE UPGRADE ....................................................................................................... 5 3.3. LOADING LICENSE KEY .......................................................................................................... 10 3.4 SAVING UNIT INFORMATION………………………………………………………………….11


PROPRIETARY

1. Document Purpose

The purpose of this document is to describe the basic configuration steps of IP-10 radio link.

Refer to the IP-10 installation and management user guides for full configuration options.

2. Document Scope

This document describes the recommended initial steps in order to connect and manage IP-10 radio link. It includes the configuration steps of the following main sections:

• Connecting to IDU using default factory setup

• Launching the web management

• SW Upgrade

• License key activation

• Basic parameters configuration

3. Startup Configuration Steps

Basic configuration includes the following basic steps:

1. Complete physical HW installation of IDU, IF coax cable, RFU and antenna as per installation instructions.

2. Connect PC to IDU and launch web management.

3. Upgrade IDU SW.

4. Load license key.

5. Configure radio link parameters.

6. Complete link commissioning.


PROPRIETARY

3.1. Launching Web-Management 3.1.1 IDU factory Default Configuration

• IP Address: 192.168.1.1, IP Mask 255.255.255.0.

• Active management port: port #7 (far right RJ45 port), out-of band management.

• License: Basic – capacity 10Mbps, no ACM, Smart Pipe (only GbE ports, ports #1 or #2)

• SW package: Basic – 1.x

• Protection: Disabled. 1+0 configuration

3.1.2 Connecting to IDU

1. Verify no Ethernet traffic (cables or fibers) connected.

2. Power up IDU.

3. Connect PC to IDU management port (port #7, far right RJ45 port).

4. PC configuration: IP Address: 192.168.1.240, IP Mask 255.255.255.0, no default gateway.

5. Verify connectivity to IDU (ping 192.168.1.1). If no connectivity, verify IDU IP management configuration using Command Line Interface (refer to Appendix).

3.1.3 Launching Web-Management

1. Open Internet Explorer.

2. Type IDU's IP address (192.168.1.1) on address field. IP-10 login screen will be displayed.

3. User: admin. Password: admin.


PROPRIETARY

3.2. IDU Software Upgrade

IDUs sent from production are loaded with basic SW version (1.1.1) that requires SW upgrade (via SW download) in order to support all system's features.

SW download is based on FTP. The IDU functions as an FTP-Client and external FTP-Server software has to be installed and running on the PC storing the SW download files.

Customers may use Windows FTP-Server or any other FTP-Server freeware available.

3.2.1 Storing Download Files on PC

IDU SW files are Linux RPM files (14 files or more). The SW files are available for download from Ceragon's FTP site (zipped together as one SW package).

1. Download zipped SW package (for example, aidu-1.4.5.zip) from FTP and save it under C:\updates.

2. Extract the aidu-1.4.5.zip to C:\updates.

3. Remove the aidu-1.4.5.zip file and store it in another location (for example, C:\IP-10).

4. Add to C:\updates folder any ODU/RFU file you may want to upgrade as well.

3.2.2 Installing FTP-Server Software

You may install and use any FTP-Server software for SW download. Ceragon recommends using FileZilla_Server-0_9_26 software that can be downloaded from the web (freeware) or from Ceragon's FTP site.

1. Download zipped FileZilla_Server-0_9_26.zip from the internet or Ceragon's FTP site and store it on the PC (for example, C:\IP-10).

2. Extract the file and run the installation setup. Follow installation process until finished (do not change any of the installation default settings).


PROPRIETARY

3.2.3 Initial Configuration of FTP-Server Software

After installing the FileZilla, it has to be configured to allow the SW download using FTP.

Stopping Windows FTP services

In order to use FileZilla, Windows default FTP services have to be stopped.

1. Go to Control Panel > Administrative Tools Internet Information Services, if the Internal Information Services don’t appear its means that the Windows FTP wasn’t install and you may have to proceed without doing so.

2. Use Right-Click to stop the Default FTP Site under FTP Sites.

Configuration of the FTP-Server software

User and files path have to be defined on the FTP-Server.

1. Launch the FileZilla Server Interface (go to Files Programs FileZilla Server FileZilla Server Interface).

2. Click OK on the Connect to Server window. The FileZilla Server window will be

displayed.


PROPRIETARY

3. Select Edit Users Shared Folders. The Users window will be displayed.

4. Select Add on the Users section and enter anonymous in the Add user Account

window.

5. Select Add on the Shared Folders section and select local drive C:\ in the Browse

for Folder.

6. Select (check) Read, Write and Delete in the Files section.

7. Verify your configuration is identical to the displayed in the following window:


PROPRIETARY

8. Select OK and close the FileZilla server.

Launching of the FTP-Server software

User and files path have to be defined on the FTP-Server.

1. Launch the FileZilla Server Interface (go to Files Programs FileZilla Server FileZilla Server Interface).

2. Click OK on the Connect to Server window. The FileZilla Server window will be

displayed.

3. Verify server is running (yellow lightning Bolt on top-left corner highlighted and

status is Logged On.


PROPRIETARY

3.2.4 SW Download Procedure

Once FTP-Server was configured and running, new SW package will be downloaded using the web-management

1. Verify SW files stored at C:\updates.

2. Verify FTP-Server configured and running.

3. Verify Windows Firewall is disabled!!!

4. Connect to IDU and launch web-management.

5. Go to General Versions and check the currently running aidu version to determine if SW upgrade is necessary.

6. Go to Diagnostics & Maintenance Software Management. The Software Management screen will be displayed:

7. In the Remote Server Parameters enter the remote FTP-Server details as per

configuration above:

a. Remote SW Update server URL: ftp://xxx.xxx.xxx.xxx/updates/ the IP should be the host’s IP. meaning the Lap Top that the SW is being download from

b. Remote server login: anonymous

c. Remote server password: leave blank

8. Select Download to start the SW downloads. This may take few minutes until completed (this operation will download all files under C:\updates to the IDU but will not activate them).

9. Select Upgrade to install the newly downloaded files. This may take few minutes until completed.

10. Restart the IDU once SW download and upgrade successfully completed.


PROPRIETARY

3.3. Loading License Key IDUs sent from production are loaded with basic license:

• License: Basic – capacity 10Mbps, no ACM, Smart Pipe (only GbE ports, ports #1 or #2)

Upgrading capacity of feature-set is done by manual entry of license key based on the IDU's Serial number. Contact Ceragon in order to obtain your license key. 1. Verify you have the license key matching the IDU Serial Number.

2. Connect to IDU and launch web-management.

3. Go to General Unit parameters and verify the IDU's Serial number matches the license key.

4. Go to General Licensing and enter the license key in the License Code field.

5. Restart the IDU.

6. Go to General Licensing and verify the correct license parameters were updated.

7. You may use the Demo license (60 days) to have full capacity and feature-set.


PROPRIETARY

3.4 Save Unit Information

3.4.2 Open the IDU and go to: /Diagnostic & management/Configuration management.

3.4.3 Go to Configuration management Parameters: and fill in as follows:

Host IP - your computer IP Host Path - // User name – anonymous User Password - enter your laptop windows user name and apply.

3.4.4 Lunch FileZilla FTP Server and make sure it’s running (yellow Bolt)

3.4.5 Under “Unit Information” click on the “Create Archive” tab and wait till the browser will disconnect you from the IDU.

3.4.6 Re-Connect to IDU and go again to: /Diagnostic & management/Configuration management.

3.4.7 Under “Unit Information” click on the “Upload Archive” tab and watch the FilleZilla FTP server screen and verify that all the files were sent to the path you have specified on the /FilleZilla/Edit/Users/Shared Folder.


PROPRIETARY

3.4.8 Go to /My Computer/C and look for a file name of xxx xxx.tar.tz and extract it to where ever you choose.

3.4.9 After extracting it go to /Var/Lib/Aidc and the file name is

“dmae_tech.log”

ip-10 quick startup guide

Documents