1

Lee Household Flour MillMODEL S-700

INTELLIGENT HEALTHFUL LIVING®

M150701302 Rev H1

3

PARTS & FEATURESMill shown may di� er in color from your appliance.

Th ank you for purchasing your Lee Household Flour Mill, model S-700. Lee Engineering has been helping households stone grind grains for over 70 years and has become synonymous with quality and durability. You and your family will appreciate the nutritional and full fl avored benefi ts of stone milled fl our.

Housing

Hopper

Inlet

Bowl

Cleaning Brush (not shown)

Hopper Cover Control Lever with nine settings

On/Off Switch

Power Cord

Parts & Features............................................................................................................ 3Important Safeguards .................................................................................................. 43 Prong Plug................................................................................................................... 5Before Using the First Time ......................................................................................... 5How to Use .................................................................................................................... 5-9 Grain Grinding.......................................................................................................... 10 Disassembly.............................................................................................................. 10-11 Cleaning .................................................................................................................... 12Specifi cations................................................................................................................ 13Warranty........................................................................................................................ 13Returns.......................................................................................................................... 13Contact .......................................................................................................................... 13Troubleshooting .......................................................................................................... 14-15

TABLE OF CONTENTS

Lee Household Flour MillMODEL S-700

Bowl CoverDisassembly

Tool

4

Basic safety precautions should always be followed when using this appliance. 1. Read these instructions thoroughly before use.

2. This appliance should not be used by children. Close supervision is necessary when using this appliance near children.

3. Do NOT leave mill unattended when in use.

4. Do NOT use in damp or wet conditions.

5. For indoor use only.

6. To protect against electrical shock, do not place cord, plug or appliance in water or other liquid.

7. Unplug from outlet when not in use or when moving or disassembling. Always unplug using the plug and not by pulling on the cord.

8. Never connect or disconnect plug with wet hands.

9. Do NOT operate flour mill with a damaged cord or plug, or if the appliance is damaged or malfunctions in any way. Call our toll-free customer service number for information regarding returning or replacing the mill. There are no user serviceable parts in this appliance.

10. Do NOT allow the cord to hang over the edge of the table or counter or come in contact with hot surfaces.

11. Only use mill on a solid, level surface.

12. Do NOT allow appliance to rest on the power cord.

13. Maintain a ventilation clearance of four inches on all sides of the mill.

14. If mill stops, or if there is excessive noise, turn power off, unplug from electrical outlet, disassemble, clean all components then reassemble machine. Discontinue use and call our toll-free customer service number if cleaning does not resolve these issues.

15. Keep fingers and other objects away from chute.

16. Do NOT push grains into chute.

17. Do NOT store your mill if any part of it is wet or damp.

18. Do NOT grind damp grains.

19. Only grind approved grains, for more information on compatible grains, visit organicsbylee.com. Grinding unapproved grains may impact the performance of your mill and/or void the warranty.

20. Clean grains before milling to remove stones or other small foreign objects.

21. Only use flour mill for its intended use.

22. For household use only. This appliance is not intended or approved for commercial use.

23. Avoid contacting moving parts.

24. The use of attachments not recommended or sold by the manufacturer may casue fire, electric shock or injury.

25. Check hopper for presence of foreign objects before using.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFEGUARDS!WARNING: ALWAYS REMOVE THE PLUG FROM THE ELECTRICAL OUTLET BEFORE

DISASSEMBLING THE MILL TO AVOID PERSONAL INJURY.

5

BEFORE USING THE FIRST TIME

1. Remove all parts from the box.2. Purge the mill by grinding 2 cups of grain or rice and discarding.3. Disassemble and brush out the mill following the instructions in the Disassembly and

Cleaning section of this manual.

WARNING: KEEP FINGERS AND OTHER OBJECTS AWAY FROM INLET TO AVOID PERSONAL INJURY OR DAMAGE TO MILL.

CAUTION: RISK OF SUFFOCATION - KEEP ALL PACKAGING AND PLASTIC BAGS OUT OF THE REACH OF CHILDREN.

HOW TO USEYour Lee Flour Mill is a gravity fed mill with a nine position control lever to change the consistency of the grind from coarse to fine. The dust cover reduces air-borne particles of your newly ground flour. The mill is equipped with a safety feature to automatically cut the motor in the event that overheating occurs. If this happens, switch the power to OFF, unplug the mill and give the motor 15 minutes to cool down before resuming use.

3-PRONG PLUG

This appliance has a 3-prong (grounding) plug for use in a 3-prong (grounding) outlet to minimize the possibility of electric shock. This appliance should only be used with a 120V, 60Hz grounded outlet. Failure to follow these instructions could result in fire, electrical shock, serious injury, or death.

If the plug does not fit fully in the outlet, contact a qualified electrician to install a 3-prong (grounding) outlet. Do not attempt to modify the plug in any way. Do not use an adapter or an extension cord. Failure to follow these instructions could result in fire, electrical shock, serious injury, or death.

66

1 PLACE THE HOPPER ON TOP OF THE CHUTE.

7

IMPORTANT: DUE TO OIL CONTENT, IT IS NOT RECOMMENDED TO GRIND SOYBEANS, NUTS OR SEEDS.

FILL HOPPER WITH APPROVED GRAINS UP TO THE DESIRED LEVEL.2

3 PLACE COVER ON HOPPER.

8

BOWL COVER

3 PRONG PLUG3 PRONG OUTLET

CHUTE

4 FIT DUST COVER ON BOWL AND CHUTE.

5 PLUG MILL INTO AN APPROVED ELECTRICAL OUTLET.

6

IMPORTANT: DO NOT OPERATE MILL WITHOUT THE BOWL AND BOWL COVER IN PLACE.

9

7 SWITCH POWER TO ON.

ON OFF

SET THE CONTROL LEVER TO DESIRED CONSISTENCY: COARSE (TOP) OR FINE (BOTTOM) OR ANY OF

THE SETTINGS IN BETWEEN.6

10

DISASSEMBLY AND CLEANING

Your Lee Household Flour Mill will provide your family with fresh flour from most dry grains such as wheat and buckwheat. For more information on compatible grains, visit organicsbylee.com

It is important to clean the mill after every usage in order to keep the mill in good working order and to avoid rancidity. Refer to the diagram on the following page to become familiar with the parts of the mill and then follow the step-by-step instructions for disassembly.

DISASSEMBLY

GRAIN GRINDING

IMPORTANT: NEVER MILL GRAINS THAT HAVE A HIGH OIL OR MOISTURE CONTENT. DO NOT ATTEMPT TO MILL WET OR DAMP PRODUCTS. DO NOT REGRIND FLOUR. HARD VARIETIES OF GRAIN MAY CAUSE THE MILL HOUSING TO BECOME VERY WARM DURING NORMAL USE.

1. Using the disassembly tool or flathead screwdriver, remove the two screws that hold the front cover on the mill housing.

2. Remove the front cover and plate.3. Grasp the quick coupler and pull straight out. 4. Pull out the governor and disk assembly.

WARNING: TO AVOID PERSONAL INJURY, ALWAYS SWITCH THE UNIT TO OFF AND REMOVE THE PLUG FROM THE ELECTRICAL OUTLET BEFORE DISASSEMBLING THE MILL.

WARNING: ANY OTHER SERVICING SHOULD BE PERFORMED BY AN AUTHORIZED SERVICE REPRESENTATIVE.

11

GRAIN GRINDING

1

2

3

4

5

6

7

8

9

10

11

12

Screws

Front Cover

Front Plate

Quick Coupler

Governor & Disk Assembly

Grinding Stone

Control Lever

Adjustable Ring

Spacer

Mill Housing

Governor Valve

Motor Shaft

PARTS

DISASSEMBLY CONT’D

Figure 1

Manually depress governor by pushing down on valve.

12

CAUTION: WHEN INSTALLING THE QUICK COUPLER, LISTEN FOR A CLICK, INDICATING THAT THE COUPLER IS FULLY SEATED ON THE MOTOR SHAFT. WHEN SEATED, THE COUPLER SHOULD ENGAGE AS FOLLOWS.

NOT SEATEDSEATED

IMPORTANT: YOU MAY NEED TO ROTATE GOVERNOR AND DISK ASSEMBLY WHILE HOLDING THE MOTOR SHAFT TO MAKE SURE IT IS PROPERLY SEATED ON THE SHAFT.

IMPORTANT: GENTLY ROTATE THE STONE WHILE INSERTING IT INTO THE MILL HOUSING TO AVOID LODGING IT.

TIP: IF YOUR STONE BECOMES WET, BE SURE TO AIR DRY FOR 48 HOURS PRIOR TO USE.

TIP: CLEAN ALL RESIDUE FROM WITHIN THE GOVENOR AND DISK ASSEMBLY.

1. Use the cleaning brush to clean the chute, both from the top and bottom.

2. Use the cleaning brush to whisk fl our dust from all parts, including the grinding stone.

3. Wash coupler and disk assembly in warm soapy water or in dishwasher.

4. Rinse or hand-wash the bowl cover and hopper in cold water and air dry.

5. Th oroughly dry all parts before reassembling the mill.

Reassemble the mill following the disassembly instructions in reverse order.

IMPORTANT: THE HOPPER IS NOT DISHWASHER SAFE.

IMPORTANT: DO NOT ATTEMPT TO CLEAN THE BOWL COVER IN A WASHING MACHINE.

WARNING: KEEP FINGERS AND OTHER OBJECTS AWAY FROM CHUTE TO AVOID PERSONAL INJURY OR DAMAGE TO MILL.

CLEANING

13

SPECIFICATIONS

Hopper Capacity

Controls

8 cups

On/off switch, nine texture set-tings (coarse to fine)

Stone Type

Electrical

Food grade stationary millstone

120 volts AC, 60 hertz, 746 watts, 7 amperes

Available Colors

Accessories

Red, black, white, green

Bowl cover, glass mixing bowl, cleaning brush, tool for

disassembling

Dimensions

9.3” W x 13.8”D x 17.6” H

RETURNS

Please refer to our website for the lateset warranty at organicsbylee.com/homemillmachine/warranty.

Prior to returning your Lee Flour Mill, please contact our toll-free Customer Service line at 1-844-781-5080 to obtain a Return Merchandise Authorization (RMA).

Send returns to:Lee Engineering, LLC1000 W. Royal Lee Dr.

Palmyra, WI 53156

WHEN RETURNING AN ITEM: • Use the original packaging and pack it securely. • Adequately insure the package in case you need to make a claim

with the carrier you choose for returning your item. • Include your order number and reason for return.

WARRANTY

SPECIFICATIONS

TROUBLESHOOTING

ISSUE CAUSE

Mill chamber clogs, mill becomes warm and flour does not come out of outlet.

High gluten grains milled on fine setting.

Governor not opening because it is clogged with flour.

Bowl is full.Bowl cover clogged (air must be able to pass through the mesh).Mill reassembled when wet.

Quick coupler not engaging on shaft. Governor is clogged with flour.

Residual grain in chute after milling.

Mill housing difficult to clean (flour paste inside of mill housing).

Rotating disk does not insert fully on motor shaft.

Mill is warm to the touch.

Excessive flour dust after milling.

This is normal.

Humidity, moisture or high gluten.

Humidity, moisture or high gluten.

High humidity.

Moist grains.High gluten grains milled on fine setting.

Disks are not aligned.

This is normal.

This is normal.

14

RESOLUTION

Adjust mill to a coarser texture.

Clean the governor thoroughly. You can test the governor by manually depressing valve (see Figure 1). Valve should move freely with finger pressure and return with spring pressure. Empty collection bowl.Clean bowl cover by brushing off any caked flour on the inside, or any blockage on top of the cover.Thoroughly air dry all parts prior to use.

Test governor by manually depressing valve and clean thoroughly (see Figure 1).

Remove bowl before removing front cover; this will help avoid mixing un-milled grains with flour.Freeze grains prior to milling.Utilize accessory flour bag, part # M150701055 instead of the Pyrex bowl and cover.Reduce ambient humidity to 50% or lower with a dehumidifier or air-conditioning.Air or oven dry grains.

Adjust mill to a coarser texture.

Rotate disk slightly until it slides on shaft completely.

To keep temperatures low, increase coarseness, mill smaller batches or freeze grain prior to milling.To reduce dust, wait for the motor to stop before removing bowl cover – you’ll see the cover decompress. You can also tap the bowl cover to remove any flour that may be caked on the underside of it.

15

16

Lee Engineering, LLC • 1000 W. Royal Lee Dr., Palmyra, WI 53156 • 844-781-5080

INTELLIGENT HEALTHFUL LIVING®

PERSONAL NOTES:

Lee Household Flour MillMODEL S-700

®