installation training manual wipro „all in one“ fiat ... · installation training manual wipro...

Installation training manual

WiPro „all in one“

Fiat Ducato 250 Evo (Euro 5) Release 07/11

Tools

Dismounting/Mounting place

Connection to CAN, hazard lights,

power supply, horn, LED

Activation/Function test

Tips and tricks

Disclaimer:

When the existing circumstances differ from the pictured, please contact the manufacturer or

alternatively our technical support.

Thitronik disclaims liability for partial or wrong installation and damages which can result from this.

Please take care of the installation instructions in the WiPro installation manual.

Insulate unused in- and outputs. Ungenutzte Ein- und Ausgänge sind zu isolieren.

Installation training manual WiPro „all in one“ - Fiat Ducato X250

Accessories / Tools / Material

-WiPro for Fiat Ducato (THS-1-00007)

-Combination pliers / Pipe wrench

-Phillips screwdriver (size 2)

-Socket wrench 10mm

-Allen key (size 3)

-Electric- or battery drill

-Drill 8mm for status LED


Programming of wireless magnetic contacts/accessories (!! Before installation !!) - Open the housing of the main unit

- Supply power to the unit

-Push and hold the button on the right of the 4 position DIP-switch, until LED

2 lights up red and the unit sounds a beep. WiPro is in programming mode now. Programmed contacts stay memorized even on power breakdown.

- Trigger every contact you wish to program into the system for several times (2 to 3 times). Successful programming will be acknowledged by a short beep.

Configuration of the CAN bus interface to vehicle type “Ducato “ - Remove power from the unit

- On the 4 position DIP-switch set position 2 to “on”. - Close the housing and continue with the installation process.

Due to the software WiPro recognizes Euro 4 and Euro 5 body computers

in the same position.


Removal of dashboard cover

Removal of body computer

Remove the three Phillips screws, as shown on the pictures. Black cover on Euro 5, grey on Euro 4. Pull cover, remove oddment tray.

Visible body computer: Remove the three screws (10mm nut), pull body computer. Future fuse of WiPro (10A).


Mounting place

Connection to CAN and hazard lights

Connection to power supply and ignition

Fiat WiPro Function Pin 9, black/orange white/orange CAN high

Pin 24, white/orange violet/orange CAN low

Pin 55, violet/orange red/pink Hazard lights

Fiat WiPro Function Pin 18, red/green red +12V (10A fuse)

Pin 17, blue/black yellow Ignition

Remove the grey plug with dark blue clamp on the back side of the body computer. Take out insert of the grey plug. Establish connections according to the table:

Remove the grey plug with light blue clamp. Take out insert of the grey plug. Establish connections according to the table:

Remove nut and Fiat ground, insert mounting plate, connect ring terminal of WiPro ground (black), reconnect Fiat ground and tighten the nut! The flat washer is for cars with Euro 4 motor.

Refit insert, reassemble plug. Put it back into the body computer.

Refit insert, reassemble plug. Put it back into the body computer.


Connection to horn

LED installation

8mm

Remove steering column cover (4 socket head screws, size 3). Make the cable harness beneath the steering wheel accessible. Connect brown/green (pin 8) cable of the harness to the pink cable of WiPro (using blue scotch lock).

Drill a hole for the status LED and bring the LED in place. Connect the red/black cable of the LED accordingly to the LED cable of the WiPro

Hint: Differing possible cable color is solid green or green/brown. Carries ground, when horn knob is pushed.


Function test Pushing the “lock” button will activate the system. In some cases it is necessary to lock and unlock the vehicle several times, before the system will react, because the CAN Bus Data needs to be synchronized at first. The activation will be acknowledged by one beep and blinking turning lights. As from now the status LED is blinking. In the case one or more cabin doors are opened, the car doesn’t lock the doors and the WiPro will not be activated. The Ducato indicator lights flash several times.

Alarm period

The alarm will sound for approx. 30 seconds. The visual alarm will stop after approx. 180 seconds. Pushing the unlock button will deactivate the system or stop the alarm.

Signals on activation

In case of a row of short beeps upon locking, one of the programmed contacts is open. The system will be activated anyways.

Troubleshooting The system is not reacting to the remote key, but sounds a beep when connecting the power supply: Check the CAN connection (pink white and pink black) Short pushing of the button on the main unit activates the diagnostic mode. The green LED flashes on traffic at the CAN bus. You can create traffic by pushing the remote key of the car. In the case no traffic is indicated, the bus is inactive or the CAN bus connection is broken. The system is not reacting to the remote key, and does not beep when connecting the power supply. Check the power supply. Did you connect the correct pin at the front side connector? Crimping connections established successfully? Fuse F39 in place and not blown? Ignition on? While ignition is on, the WiPro is disabled. Even all contacts are closed, an opened contact is signalised when activating the system. Check the distance between the transmitter and the magnet. Open and close all contacts several times > activate again. Still an open contact is signalised > Disconnect the power supply or take out F39 (all contacts closed) > re-establish the power supply.

installation training manual wipro „all in one“ fiat ... · installation training manual wipro...

Documents