installation rÉguliÈre g-key (80-bit) page 1 / 5 rev ... · release insert the required remaining...
TRANSCRIPT
ONE REV.: 20170112
ADDENDUM - SUGGESTED WIRING CONFIGURATION ADDENDA - SCHÉMA DE BRANCHEMENT SUGGÉRÉ
ADDENDUM - SUGGESTED WIRING CONFIGURATION
SCHÉMA DE BRANCHEMENT SUGGÉRÉG-KEY (80-BIT)
SCION / TOYOTA
OBD-II connectorConnecteur OBD-II
NOTE : functional if equipped with a factory hood switch. fonctionnel si équipé d'un commutateur de capot d'origine.
Hood Status
Page 1 / 5 Rev.20120408 GUIDE # BETA
Au
toLi
ght
iQ 2012-2013G Key (80-BIT)
Main body ECU
Copyright © 2012, Fortin Auto Radio Inc
Doorlock DATA
tC 2011-2013G Key (80-BIT)4Runner 2010-2013G Key (80-BIT)Yaris Hatchback 2012-2013G Key (80-BIT)
HARDWARE VERSIONVERSION DU MATÉRIEL Date: xx-xx
HARDWARE VERSION : 3 FIRMWARE VERSION : 4.0+
Service No : 000 102 04 2536
INTERFACE MODULE
Made in Canada
PATENTS PENDING US: 2007-228827-A1
www.fortinbypass.com
EVO
3Minimum
FIRMWARE VERSIONVERSION DU LOGICIEL
[ ]Minimum0379.
Toyota/Lexus
1
9 10
2 3 4
11 12
5
13
7 8
15 16
6 7
14
CAN HIGH Pin 6
CAN LOW Pin 14
IMMO DATAPin 7
Ignition connectorConnecteur Ignition
Copyright © 2012, Fortin Auto Radio Inc
Copyright © 2010, Fortin Auto Radio Inc
Parking Light switch harnessHarnais feux de stationnement
Copyright © 2012, Fortin Auto Radio Inc
(-)Parking Lights(-)AutoLight
Au
toLi
ght
Co
ntr
ol
This manual may change without notice. www.fortinbypass.com for latest version.
Ce Guide peut faire l'objet de changement sans préavis.www.fortinbypass.com pour la récente version.
G
80-bitADDENDUM - SUGGESTED WIRING CONFIGURATION
SCHÉMA DE BRANCHEMENT SUGGÉRÉG-KEY (80-BIT)
SCION / TOYOTA
OBD-II connectorConnecteur OBD-II
NOTE : functional if equipped with a factory hood switch. fonctionnel si équipé d'un commutateur de capot d'origine.
Hood Status
Page 1 / 5 Rev.20120408 GUIDE # BETA
Au
toLi
ght
iQ 2012-2013G Key (80-BIT)
Main body ECU
Copyright © 2012, Fortin Auto Radio Inc
Doorlock DATA
tC 2011-2013G Key (80-BIT)4Runner 2010-2013G Key (80-BIT)Yaris Hatchback 2012-2013G Key (80-BIT)
HARDWARE VERSIONVERSION DU MATÉRIEL Date: xx-xx
HARDWARE VERSION : 3 FIRMWARE VERSION : 4.0+
Service No : 000 102 04 2536
INTERFACE MODULE
Made in Canada
PATENTS PENDING US: 2007-228827-A1
www.fortinbypass.com
EVO
3Minimum
FIRMWARE VERSIONVERSION DU LOGICIEL
[ ]Minimum0379.
Toyota/Lexus
1
9 10
2 3 4
11 12
5
13
7 8
15 16
6 7
14
CAN HIGH Pin 6
CAN LOW Pin 14
IMMO DATAPin 7
Ignition connectorConnecteur Ignition
Copyright © 2012, Fortin Auto Radio Inc
Copyright © 2010, Fortin Auto Radio Inc
Parking Light switch harnessHarnais feux de stationnement
Copyright © 2012, Fortin Auto Radio Inc
(-)Parking Lights(-)AutoLight
Au
toLi
ght
Co
ntr
ol
This manual may change without notice. www.fortinbypass.com for latest version.
Ce Guide peut faire l'objet de changement sans préavis.www.fortinbypass.com pour la récente version.
G
80-bitVehicle functions supported in this diagram (functional if equipped) | Fonctions du véhicule
supportées dans ce diagramme (fonctionnelles si équipé)
VEHICLEVEHICULES
YEARS ANNÉES Im
mob
ilize
r byp
ass
Con
tour
nem
ent
d’im
mob
ilisa
teur
T-H
arne
ss a
vaila
ble
(sol
d se
para
tely
)H
arna
is e
n T
disp
onib
le
(ven
du s
épar
émen
t)
Lock
Unl
ock
Arm
Dis
arm
Trun
k (o
pen)
Tach
omet
er
Doo
r Sta
tus
Trun
k S
tatu
s
Hoo
d S
tatu
s
Han
d-B
rake
Sta
tus
Foot
-Bra
ke S
tatu
s
Auto
-ligh
t Con
trol
SCIONiQ G-Key (80-BIT) 2012-2015 • • • • • • • • • • • • • •TOYOTA4Runner G-Key (80-BIT) 2010-2016 • • • • • • • • • • • • • •Yaris Hatchback G-Key (80-BIT) 2012-2015 • • • • • • • • • • • • • •
Guide # 29791
Program remote starter option:
Programmez l’option démarreur à distance:
FUNCTIONFONCTION MODE DESCRIPTION
2 4(+) Start 2 (E1)
(+) Ignition 2 (E2)
(+) Démarreur 2 (E1)
(+) Ignition 2 (E2)
This manual may change without notice www.fortinbypass.com for latest version.Ce Guide peut faire l’objet de changement sans préavis. www.fortinbypass.com pour la récente version.
Page 1 / 5
REGULAR INSTALLATION INSTALLATION RÉGULIÈRE
Yellow In A1 Purple Out A2
Purple/White Out A3 Green Out A4 White Out A5
Orange Out A6 Orange/Black Out A7
Dk.Blue Out A8 Red/Blue In A9
Lt.Blue/Black In/ Out A10 Black In A11 Pink Out A12
Yellow/Black Out A13 Brown/White In A14
Pink/Black In A15 Purple/Yellow In /Out A16 Green/White In /Out A17
Green/Red In /Out A18 White/Black Out A19
Lt.Blue In /Out A20
C5 Brown C4 Gray/Black C3 Gray C2 Orange/Brown C1 Orange/Green
D6 White/Red D5 White/Blue D4 White/Green D3 Yellow/Red D2 Yellow/Blue D1 Yellow/Green
White Out E1 Orange Out E2
Red In E3 Black In E4 Pink In/ Out E5
Yellow Out E6
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
WIRING CONNECTION | GUIDE DE BRANCHEMENTS
Violet White4Runner GreenRed RedPin8 Black Pin6Green Pin7 Black Pin1Purple Pin4PinkGray WhiteYaris BlackLt.Blue GreenPin7 Pink Pin6White Pin5 Blue Pin7Lt.Blue Pin1Pink
C4C3CAN High CAN LowViolet WhiteiQ
(+)Ignition1(+)Starter1 (+)12V (+)Starter2
OBDIIFront viewVue de face
Back view -White connector Ignition harnessVue de dos - Connecteur BlancHarnais Ignition
1
9 10
2 3 4 5
11 12 13
A10IMMO DATARed
(-)Parking LightsYellow
1234
5678
LtGreenPin1 Brown Pin6Blue Pin7 Red Pin8(+)Ignition2Lt.Blue Pin4
65
151413
242322
121110
212019
987
321
Back view - 30-Pin White connectorMain body ECU
Vue de dos - 30-Pins Connecteur BlancMain body ECU
25
A20Doorlock DATABrown
876
14 15 1614
4
181716
2726 302928
CU
T
Back view White connector Light switchharnessVue de dosConnecteur BlancHarnais feux de stationnement
(-)AutoLightGreenGreenGreen
12345678910
14151617181920 13 1112
D3
D1
A12 E6E5E2E1 E3
GroundMasse
( - )A u to L ig h t
( - )A u to L ig h t
CUT LOOP FOR AUTOMATIC TRANSMISSION MODE.COUPEZ LA BOUCLE POUR LE MODE TRANSMISSION AUTOMATIQUE.
CAN HIGHCAN LOW
(+)Starter(+)Ignition(-)Ground
(+)12V(+) Ignition2
(+)Start2(-) Data Door Lock
(-)Parking Lights
(~) IMMO DATA
(+)Ignition
Yellow/Blue
White/GreenWhite/BlueWhite/Red
Orange/GreenOrange/Brown
Brown
White/BlackGreen/Red
Green/WhitePurple/Yellow
Pink/BlackBrown/WhiteYellow/Black
Black
Red/BlueDk.Blue
Orange/BlackOrange
WhiteGreen
Purple/WhitePurple
Page 2 / 5
A EFGJ I
H B C D
FLASH 10XIGNITION ON
FLASH 10X
FLASH
A
E
F
G
J
I
H
B
C
D
ON
PRESS X2
KIA RIO - PUSH-TO-START
This Guide may change without notice. www.ifar.ca for latest version. Ce Guide peut faire l'objet de changement sans préavis. www.ifar.ca pour la récente version.
PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION
1
Press and hold the programming button:Insert the 6-Pin Main connector.
Appuyez et maintenir le bouton de programmation enfoncé: Insérez le connecteur Principal à 6-broches.� The LED will alternate
between BLUE, YELLOW, RED, BLUE, YELLOW and RED flashes.
� Les DELS alternent entre un flash BLEU, JAUNE, ROUGE et BLEU et ROUGE.
Release the programming button when the LED are BLUE & RED.
Si le DEL ne sont pas BLEU et ROUGE débranchez le connecteur 6 pins (Connecteur principal) et allez au début de l'étape 1.
2
Relâchez le bouton de programmation quand les DELs sont BLEU et ROUGE.
If the LED are not solid BLUE and RED disconnect the 6-Pin connector (Main-Harness) and go back to step 1.
RELEASE
Insert the required remaining connectors.
3
4
Insérez les connecteurs requis restants.
Press and release the programming button twice (2x).
x2PRESS
Appuyez et relâchez 2 fois le bouton de programmation.
ON
5
LO
CK
ACC ON
PUSH
STA
RT
IGN
TURNON/RUN
6
Turn the Ignition to the ON/RUN position.
Tournez la clé en position ignition (ON).
� The RED and BLUE LEDs will flash rapidly 10x times. Key bypass programmed.
� La DEL ROUGE et BLEU clignoteront 10x fois rapidement. Contournement de clé programmé.
Turn the Ignition to the OFF position.
LO
CK
ACC ON
PUSH
STA
RT
OFF Tournez la clé à OFF.
� The BLUE LED will turn off. � La DEL BLEU s'éteint.
TURNOFF
The module is now programmed.
Le module est programmé.
Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.
Testez toutes les fonctions supportées sur le véhicule avec la télécommande du démarreur à distance ou du système de sécurité.
WAIT � The BLUE LED will flash rapidly. CAN-Bus programmed.
� La DEL BLEU clignotera rapidement: Réseau CAN programmé.
Wait Attendre
Page 4 / 5
� The RED and BLUE LED will flash.
� Les DELs ROUGE ET BLEU clignotent.
OFF ON OFF ON
Page 4 / 6
CETTE PROGRAMMATION EST POUR LES TOYOTA LEXUS SCION GKEY 80BITS
x1HOLD
A
E
F
G
J
I
H
B
C
D
LED may differ depending on the module casing.L’apparence des DELS peut différer selon le boîtier du module.
A
E
F
G
J
I
H
B
C
D
ONBLUE BLEU
ONREDROUGE
A
E
F
G
J
I
H
B
C
D
A
E
F
G
J
I
H
B
C
D
A
E
F
G
J
I
H
B
C
D
A
E
F
G
J
I
H
B
C
D
A EFGJ I
H B C D
IGNITION ON IGNITION OFF
OFF
A
E
F
G
J
I
H
B
C
D
FLASH 10X
Ne pas utiliser la clé grise.Do not use the grey key.
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
KEY BYPASS PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ
Page 3 / 5
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
REMOTE STARTER PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION DU DÉMARREUR À DISTANCE
REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.
RÉFÉREZ-VOUS AU GUIDE D’INSTALLATION RAPIDE INCLUS AVEC LE MODULE POUR LA PROGRAMMATION DU DÉMARREUR À DISTANCE.
VEHICLE EQUIPPED WITH OEM ALARM | VÉHICULE ÉQUIPPÉS D’UNE ALARME D’ORIGINE
Some vehicles must be UNLOCKED to disarm the OEM alarm before remote start. Enable option D2 using the FlashLink Manager. When this option is enabled the module will automatically UNLOCK before remote start and LOCK after the vehicle has remote started.
Certains véhicules doivent être DÉVERROUILLÉS avant le démarrage à distance pour désarmer l’alarme d’origine. Activez l’option D2 avec le FlashLink Manager. Lorsque cette option est activée, le module déverrouille automatiquement avant le démarrage à distance et reverrouille après que le véhicule a démarré à distance.
Page 4 / 5
Service No : 000 102 04 2536
Date: xx-xx
INTERFACE MODULE
Made in CanadaPATENTS PENDING US: 2007-228827-A1
www.fortinbypass.com
HARDWARE VERSION FIRMWARE VERSION
Module label | Étiquette sur le module
Notice: Updated Firmware and Installation GuidesUpdated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
Notice: Mise à jour microprogramme et Guides d’installationsDes mises à jour du Firmware (microprogramme) et des guides d’installation sont mis en ligne régulièrement. Vérifi ez que vous avez bien la dernière version logiciel et le dernier guide d’installation avant l’installation de ce produit.
WARNINGThe information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.
MISE EN GARDE L’information de ce guide est fournie sur la base de représentation (telle quelle) sans aucune garantie de précision et d’exactitude. Il est de la seule responsabilité de l’installateur de vérifi er tous les fi ls et circuits avant d’effectuer les connexions. Seuls une sonde logique ou un multimètre digital doivent être utilisés. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité de l’exactitude de l’information fournie. L’installation (dans chaque cas) est la responsabilité de l’installateur effectuant le travail. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité suite à l’installation, que celle-ci soit bonne, mauvaise ou de n’importe autre type. Ni le manufacturier, ni le distributeur ne se considèrent responsables des dommages causés ou ayant pu être causés, indirectement ou directement, par ce module, excepté le remplacement de ce module en cas de défectuosité de fabrication. Ce module doit être installé par un technicien qualifi é. L’information fournie dans ce guide est une suggestion. Ce guide d’instruction peut faire l’objet de changement sans préavis. Consultez le www.fortinbypass.com pour voir la plus récente version.
Copyright © 2006-2014, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORTTél: 514-255-HELP (4357) 1-877-336-7797
ADDENDUM GUIDEWEB UPDATE | MISE À JOUR INTERNET
www.fortinbypass.com
ONE
Page 5 / 5