installation & owners manual hercules ii 750...hercules ii 750 vertical platform lift manual...
TRANSCRIPT
P/N: 630-00046 RevD 111518
This manual has been provided to assist you with lift installation and operation.For further assistance please contact your authorized AmeriGlide dealer orAmeriGlide’s Technical Support Department.Tel: 866-378-6648Fax: 816-537-0641
Installation &Owners ManualHERCULES II 750Vertical Platform Lift
Dealer:
Serial No:
MODELS:AMGHERC750-4 AMGHERC750-6 AMGHERC750-8
AMGHERC750-10 AMGHERC750-12 AMGHERC750-14
Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-66482 // 32
P/N: 630-00046 RevD 111518
TABLE OF CONTENT
Using the Manual _______________________________________ 3When You Receive the Lift Specifications ________________ 4Safety __________________________________________________ 4Code Requirements _____________________________________ 5Site Requirements ______________________________________ 5Required Tools__________________________________________ 5 Required Materials _____________________________________ 5Preparing to Install the Lift ______________________________ 6Controller Harness Connections _________________________ 6Installing the Platform __________________________________ 7Installing the Outer Guard Panel ________________________ 8Installing the Fixed Ramp _______________________________ 8Installing the Folding Ramp _____________________________ 9Anchoring the Lift ______________________________________ 10Setting the Limit Switches _____________________________ 11Verifying Operation of the Lift __________________________ 12Manual Override _______________________________________ 13Call-Sends (optional) _________________________________ 13Top Landing Gate (optional) ___________________________ 14EMI and Flush Strike (optional) ________________________ 15Platform Gate (optional) _______________________________ 16Fascia Panel (optional) ________________________________ 17Alarm __________________________________________________ 17Owner’s Section _______________________________________ 18Safety _________________________________________________ 19Controls _______________________________________________ 20Operating the Lift ______________________________________ 21Wiring _________________________________________________ 23Warranty ______________________________________________ 30
3 // 32Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
Using the ManualThis manual will provide step by step instructions on how to install and operate your lift. Read and understand the entire manual before beginning to install the lift.
If you have any questions, contact Technical Service at 1-866-378-6648.
INDICATIONS OF USE STATEMENTThe Hercules II 750 vertical platform lift assists with the transfer of patients or mobility impaired persons, up and down between levels of a residential or private facility.
Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-66484 // 32
P/N: 630-00046 RevD 111518
LIFT SPECIFICATIONS
WHEN YOU RECEIVE THE LIFT
• Check the lift for shipping damage. If you see any damage contact the freight carrier to file a damage claim.
• Verify that products match what’s described on the packing list attached to the exterior packaging.
SPECIFICATIONS
Payload Capacity 750 lbVertical Travel 53" - 171"Foot Print VariesPlatform Size 36" x 54" | 36" x 60" | 42" x 54" | 42" x 60"Input Voltage 115 VAC - 20 AControl Voltage 24 VAC or 24 VDCPlatform Speed 10' minMotor 1/ 3 HP - 90 VDC or 1/ 3 HP - 24 VDC
SAFETY
• Read all instructions in this manual before installing or operating the lift.• Do not exceed the maximum payload capacity of 750 lb.• Do not ride on the lift until it is anchored in place.• This product is designed only for lifting people and wheel chairs. Do not use it for
any other purpose.• Always wear eye protection while installing or servicing this product.• Always disconnect this product from the electrical source before servicing it.• Only use the fasteners supplied with this lift.• Do not wear loose clothing or jewelry when working on this product.• Do not disable any safety equipment or switches supplied with this lift.• Stay away from all drive train components while the lift is operating.
5 // 32Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
REQUIREMENTS
WHEN YOU RECEIVE THE LIFT
• Check the lift for shipping damage. If you see any damage contact the freight carrier to file a damage claim.
• Verify that products match what’s described on the packing list attached to the exterior packaging.
SPECIFICATIONS
Payload Capacity 750 lbVertical Travel 53" - 171"Foot Print VariesPlatform Size 36" x 54" | 36" x 60" | 42" x 54" | 42" x 60"Input Voltage 115 VAC - 20 AControl Voltage 24 VAC or 24 VDCPlatform Speed 10' minMotor 1/ 3 HP - 90 VDC or 1/ 3 HP - 24 VDC
SAFETY
• Read all instructions in this manual before installing or operating the lift.• Do not exceed the maximum payload capacity of 750 lb.• Do not ride on the lift until it is anchored in place.• This product is designed only for lifting people and wheel chairs. Do not use it for
any other purpose.• Always wear eye protection while installing or servicing this product.• Always disconnect this product from the electrical source before servicing it.• Only use the fasteners supplied with this lift.• Do not wear loose clothing or jewelry when working on this product.• Do not disable any safety equipment or switches supplied with this lift.• Stay away from all drive train components while the lift is operating.
CODE REQUIREMENTS
Your lift has been designed to meet ASME A18.1 section 2 and CSA B44.1/ASME A17.5, with the addition of certain options. Code requirements for Vertical Platform lifts vary depending on location. It is the installers responsibility to contact their local code enforcement office and determine all of the regulations they are subject to. You must do this before installing the Vertical Platform Lift.
SITE REQUIREMENTS
• The lift will require a 115 VAC 20 AMP grounded circuit.
• Outdoor Installations will require a GFI protected circuit. (check with jurisdiction)
• Only install the lift on a 4" thick, level 3,500 PSI reinforced concrete slab.
• Foot Print varies depending on platform size and options. REQUIRED TOOLS
• Screwdrivers• 1/ 2" Hammer Drill
• 3/ 8" Masonry Drill Bit
• Appliance Dolly
• Hammer
• Level
• Measuring Tape
• Socket Wrench Set
• Voltmeter
REQUIRED MATERIALS
• 4 Floor anchors
AmeriGlide recommends securing the lift using our Anchor Kit. If you purchase you own floor anchors they must use 3/ 8" bolts and have a minimum tensile strength of 6000 lb.
Note:Lift must meet NFPA70 (National Electrical Code)
6 // 32 Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
INSTALLATION PROCEDURES
PREPARING TO INSTALL THE LIFT
Final Site Inspection
Verify the surface the lift will mount to is smooth and level. This surface must be made from 3,500 PSI reinforced concrete with a minimum thickness of 4".
• The horizontal gap between the edge of the platform and the upper landing must no less than 3/ 8" and no greater than 3/ 4".
• The horizontal gap between the guard panel and any wall or barrier must be no less than 2" and no greater than 3".
• Verify that sufficient head room exists above the lift. The lift will require 6' 8" of clearance above the platform floor when the lift is at the upper landing.
Connecting to Electricity
The lift will require a 115 VAC 20 AMP grounded electrical circuit. Depending on local codes, this connection may need to be routed in electrical conduit and hard-wired.
Controller Harness Connections
CautionVerify that the running clearance around the lift complies with ASME A18.1 codes for your area.
Warning:Do not ride on the lift until it has been anchored in place.
Warning:The area between the floor where the lift is mounted and the top landing must be covered by a smooth vertical fascia. This is to eliminate any pinch points between the platform and
High VoltageCicuit Break
(AC unit only)
Low VoltageCircuit Breaker
PlatformTraveling Cable
Safety Pan Jumper
Upper Landing Interlock
Upper & Lower Limit Switch
Bypass Switches(strikes only)Upper & Lower
Call-SendsLower Landing
Interlock3-Stop only
7 // 32Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
INSTALLATION PROCEDURES
Step 5: Install two (2) joint fasteners and firmly tighten with 3/16" Allen wrench. Then slide rack pieces down to cover joint.Step 6: Turn over joined rails and install the remaining two (2) joint fasteners and firmly tighten with 3/16" Allen wrench. Then slide rack pieces down to cover joint.Step 7: Install rail brackets by loosening the screws and snapping each bracket edge into the slot, or
slide the brackets on from the top of the rail.
When in final position, the nuts will be on the wall side.Step 8: ________________________ A. For double rails, tighten the first rail bracket
in place so that, _________________________________________ when turned over, the back of the bracket touches the rear of the _______________________ first step from the bottom landing. Place and tighten the second _______________________ and third brackets on the steps on each side of the rail joint, again _______________________ so the back of the bracket touches the rear of the step. Then _____ place the fourth and final bracket on
the last step before the top ________________ ______________________________________landing, again tightening it so it touches the front of the rear of the last step. ______________________________________B. For single rails, tighten the first rail bracket in place so that, ___________________
INSTALLING THE PLATFORM
Step 1: The mounting bolts, nuts and spacers that secure the platform to the lift carriage are packaged in the small parts box. Begin by locating these pieces and setting aside.
Step 2: Position the platform by aligning the support legs with the carriage flanges that protrude from the front cover.
Step 3: Align the four mounting holes with those on the carriage. Insert 1/ 2 x 3" hex head bolts into each of the (4) holes. Install the low profile nuts on the upper bolts and the standard ones on the lower bolts.
Step 4: Plug in the harness for the platform safety pan and unplug the safety pan jumper on the controller (ref pg 5). Secure the harnesses under the clip on top of the carriage flange.
8 // 32 Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
INSTALLATION PROCEDURES
INSTALLING THE PLATFORM GUARD PANELS
Step 1: Insert the guard panel posts in the pockets in the platform. The smooth side of the guard panel faces toward the center of the platform. Bolt each post in place with (2) 5/ 16 -18 x 2" and (1) 1/ 4 -20 x 2" hex head bolts.If you have a 90° exit platform, install the end guard panel using the provided bracket and bolt to inner guard panel.
Step 2: Install the platform control box on the rear guard panel using screws and nuts through the panel.
Step 3: Plug in the harness for the platform control box. Secure the harnesses under the clip on top of the carriage flange.
INSTALLING FIXED RAMP • Position the ramp after the lift is in its
final location.• Maintain a gap of 3/ 8" to 3/ 4" between
the ramp and platform.• Drill a pilot hole into the concrete and
fasten using supplied concrete lags through ramp flanges.
9 // 32Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
Step 4: Attach the ramp roller arm by bolting it to the underside of the ramp.
The ramp roller should align and make contact with the ramp roller guide.
Step 1: Install the ramp roller guide on the side of the lift tower using the screws already installed in the panels.
Step 2: Attach the two ramp pivot tabs to the lower landing sides of the platform. Reinsert the hex bolts, one of which will go through the guard panel post, and tighten.
Step 3: Attach the ramp to the pivot tabs using shoulder bolts and locking nuts. Tighten the nuts until they seat against the bolt shoulder.
INSTALLING AUTO-FOLDING RAMP (OPTIONAL)
Rave Stair Lift Manual | www.Ameriglide.com | 866-378-6648
INSTALLATION PROCEDURES
10 // 32 Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
ANCHORING THE LIFT
AnchorsAmeriGlide recommends securing the lift using the concrete anchors provided. If you purchase you own floor anchors they must be 3/ 8" minimum of sufficient length. All four floor anchors must be installed correctly in accordance to their instructions. Step 1:
• Position the lift in its final location.
• Verify that it is level and perpendicular to its surroundings and all running clearances are the proper dimension.
• Shim if necessary.Step 2: Use the lift’s base as a template. Drill 4 holes into the concrete making sure that the holes are deep enough to accept the anchors. Step 3: Secure the lift in place by tightening the floor anchor bolts.
Step 4: (800 or taller models)Taller lifts must have the top of the lift tower anchored into a solid surface to ensure running clearances remain constant.There are two options for anchoring the top of the tower: 1. For lifts going up to a landing such as a
deck or porch, the optional tower brace is the preferred method. Hardware is packed with tower brace.
2. For lifts that are placed with the back of the tower against a solid wall such as inside of a hoistway, drilling two holes through the top tower cross brace and anchoring is preferred.
TipConcrete dust may have settled into the holes you just drilled. Use a shop vacuum to clean out these holes. This will ensure the floor anchors set correctly.
Anchor two locations
11 // 32Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
SETTING LIMIT SWITCHES
SETTING THE LIMIT SWITCHES
Your lift is equipped with upper and lower limit switches. The vertical location of these switches may be adjusted to fit your application. Typically the upper limit switch will need to be adjusted so the platform will stop level with the upper landing. The lower limit will typically not need adjusting.
Step 1: Verify the emergency switch is in the ON position. Run the lift in the up direction until the platform floor is level with the upper landing. Disconnect the lift’s power (at the building’s circuit breaker for AC units, at the battery box for DC units) before going to the next step.
Step 2: Remove the screws at the top of the lift that attach the front cover.
Step 3: Remove the front cover by tilting it forward and lifting upwards. The bottom of the front cover sits on a pin on either side of the lift frame. Set the cover aside in a safe location where it will not get damaged.
WarningMoving components can cut and crush. Do not operate the lift if you are in close proximity to any drive components. Be aware that loose clothing or jewelry may catch on moving parts.
Step 4: Loosen the bolts that attaches the upper limit switch assembly. Slide the assembly down the track until the lower switch in the assembly comes in contact with the lift’s car. You should hear the limit switch click as contact is made. Retighten the set screw fastening the limit switch assembly in place.
Step 5: Replace the front cover and secure it with the screws from step 2.Step 6: Re-connect the lifts electricial power at the circuit breaker. Verify that the emergency switch is in the on position.Step 7: Run the lift in the down direction for several inches. Next, run the lift in the up direction. Continue to press the up button until the upper limit switch has caused the lift to stop. Verify that the platform has stopped level with the upper landing. If it has not, readjust the limit until it is level.
12 // 32 Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
VERIFYING OPERATION OF LIFT
VERIFYING OPERATION OF THE LIFT
Step 1: Run the lift up and down for 5 complete cycles. Hold the direction button down and allow the limit switches to stop the lift. At the top, verify that the platform stops level with the upper landing. At the bottom, verify the access ramp (if equipped) unfolds and rests on the ground. Step 2: Verify the operation of the Emergency stop switch. When this switch is pushed in the lift should not run in either direction. When this switch is turned and pulled back out, the lift should operate normally.
Step 3: Verify the operation of the sensor pan underneath the platform. Start with the lift at the top landing. Press up on the sensor pan. While holding the pan in this location, press the down switch on the platform. The lift should not run.
CautionComplete the following section before training the customer to use the lift.
WarningDo not run the lift if anyone is under the platform.
13 // 32Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
MANUAL OVERRIDE
Your lift is equipped with a manual handcrank, to be used in the case of a power failure.Before using the manual handcrank verify that it’s use is required. Check that the emergency stop switch is pulled out. Check that the electrical cord is connected to the supply. Also check that the buildings circuit breaker has not tripped. Try to run the lift by pushing both the up and down buttons. If the lift still will not run, complete the following steps:
Step 1: Disconnect the power from the lift.
Step 2: Remove the screws and remove the top cap at the top of the tower.
Step 3: Insert the manual handcrank into the opening on the top of the brake assembly. It may be neccesary to slightly rotate the handcrank until it fully seats down on the hex portion of the brake. Rotate the crank to raise or lower the platform.
CALL-SENDS (OPTIONAL)
The optional Call-Send controls are to be used at the upper and/or lower landings to call the platform to you or send it to the other landing.
They should be mounted on the wall at each landing. ASME A18.1 code is 15" to 48" from floor.
A length of multi‐conductor wire will need to be ran from the bottom of the lift tower up to the landing Call‐Sends. Consult local codes for type and mounting requirements. After wiring is completed, the wiring harness must be plugged into it appropriate receptacle on the controller (ref pg 6).
Wiring Connections
Call-Send Lift HarnessBlue Blue
White WhiteRed Red
WarningDo not service or operate the manual handcrank while the lift is connected to electricity.
WarningNever operate the lift while the manual override crank is inserted into the lift.
14 // 32 Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
TOP LANDING GATE (OPTIONAL)
The optional top landing gate is provided with a combination mechanical lock and electric contact (interlock).
The interlock:
• Prevents the lift from running if the gate is not closed.
• Prevents the gate from being opened if the platform is not at the top landing.
• Unlocks when the lift is on the upper limit switch.
A crescent shaped key is provided to manually unlock the gate during installation. The key is inserted from the back side to lift up on the solenoid that holds the gated locked. Mount the gate by placing onto the upper landing making sure to align the gate opening with the platform (outer guard rail not shown for clearity). There are a number of attachment holes provided in the threshold portion of the gate for mounting using wood lag screws or concrete anchors as appropriate. Remove the latch post cover and connect the call-send and interlock wire harnesses.
The vertical posts of the gate must be attached to a supporting structure, (the gate is not designed to be freestanding).A length of multi‐conductor wire will need to be ran from the bottom of the lift tower up to the landing gate. Consult local codes for type and mounting requirements. After wiring is completed, the wiring harness must be plugged into it appropriate receptacle on the controller (ref pg 6).
Wiring ConnectionsInterlock_Harness Lift Harness
Black BlackBlack GreenYellow WhiteYellow Orange
* Blue* Brown
* Must be tied together
Call/Send Harness Lift HarnessBlue Blue
Yellow WhiteRed Red
15 // 32Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
EMI AND FLUSH STRIKE INTERLOCKS (OPTIONAL)
For Optional DC powered liftsFolger/Adams Strike Wires Lift Harness Wires
Black BlackPurple GreenWhite White
Orange OrangeYellow BlueBrown Brown
NOTE: Blue and Green from strike not used.
EMI Interlock1. Position interlock to
door jamb and mark mounting holes.
2. Fasten Interlock to door jamb with #8 wood screws.
3. Route 4-conductor Interlock cable thru hole in top of interlock and make wire connections.
4. Attach door keeper and emergency key plates to hoistway door.
EMI Interlock Wiring Connections
EMI Lift Harness WiresBlack (A) BlackBlack (B) GreenYellow (C) WhiteYellow (D) Orange
— Blue*— Brown*— Red
* Must be tied together when using an EMI Interlock.
The optional EMI or Flush Strike Interlocks are provided with a combination mechanical lock and electric contact. They are to be used with existing doors.
The interlock: • Prevents the lift from running if the gate
is not closed.• Prevents the door from being opened if
the platform is not at the landing.
A length of multi-conductor wire will need to be ran from the bottom of the lift tower to each interlock. Consult local codes for type and mounting requirements. After wiring is completed, the wiring harness must be plugged into it appropriate receptacle on the controller (ref pg 6).
Flush Strike InterlockRefer to the instructions inside the strike box for mounting requirements.
Flush Strike Interlock Wiring Connections
For AC powered liftsFolger/Adams Strike Wires Rectifier Wires Lift Harness Wires
Purple Red —
Purple Black —
— Yellow Black
— Yellow Green
White — White
Orange — Orange
Yellow — Blue
Brown — Brown
NOTE: Blue and Green from strike not used.
Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
16 // 32 Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
PLATFORM GATE
PLATFORM GATE (OPTIONAL)
The optional platform gate is provided with a combination mechanical lock and electric contact (interlock). The interlock:
• Prevents the lift from running if the gate is not closed.• Prevents the gate from being opened if the platform is not at the bottom landing.• Unlocks when the lift is on the lower limit switch.
A crescent shaped key is provided to manually unlock the gate during installation. The key is inserted from the back side to lift up on the solenoid that holds the gated locked. Mount the gate by placing onto the lower landing side of the platform. There are a number of attachment holes along the bottom and up the sides of the gate frame to attach to the platform and guard panels.
A wiring harness included on the gate will need to be routed along the gate frame, behind the rear guard panel and connected to its adjoining harness plug on the lift carriage. After wiring connection is made, the wiring harness must be plugged into its appropriate receptacle on the contoller (ref pg 6).
17 // 32Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
FASCIA PANEL
FASCIA PANEL (OPTIONAL)
A fascia panel provides a smooth surface for the platform edge to run against to prevent any shear or obstruction hazards and must be utilized.A running clearance of no more than 3/ 4" and no less than 3/ 8" must be maintained between the edge of the platform and the fascia panel.
PLATFORM CONTROL WITH OPTIONAL E-STOP ALARM
If equipped, the e-stop button on the platform lights up and sounds an alarm when pressed. You will need to obtain a 6 VOLT lantern battery like the example below.
The battery can sit under the top cap to the right of the motor pulley. There is a wire harness for the battery located here. Wire #1 connects to the positive terminal and wire #2 to the negative terminal.
18 // 32 Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
COMMERCIAL PLATFORM LIFTOWNERS SECTION
READ THE MANUAL THOROUGHLY BEFORE OPERATING THE LIFT.
19 // 32Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
Congratulations on the purchase of your AmeriGlide Vertical Platform Lift. This lift has been engineered to provide trouble free service for many, many years. Please read this manual completely before operating your lift.
SAFETY
• Do not exceed the maximum payload capacity of 750 lb
• Do not ride on the lift until it is anchored in place.
• This product is designed only for lifting people and wheel chairs. Do not use it for any other purpose.
• Make sure any obstructions are cleared from underneath the platform area before use.
• Make sure both the passenger and wheelchair are completely on to the platform before using.
• Do not disable any safety equipment or switches supplied with this lift.
• Do not attempt to service the lift yourself. Contact your AmeriGlide dealer for assistance.
• Do not allow children to operate or play around the lift.
• Read all instructions in this manual before installing or operation the lift.
20 // 32 Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
CONTROLS
Emergency Stop
In an emergency push this red button to stop the lift. Turn the button clockwise to run.
Up
Controls upward movement of lift platform. To move platform up, depress and hold the upper half of the rocker switch. To cease movement, release switch.
Down
Controls downward movement of lift platform. To move platform down, depress and hold the lower half of the rocker switch. To cease movement, release switch.
Keylock (optional)
Disables controls from operating when keylock is turned off.
21 // 32
GLOSSARY
Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
OPERATING THE LIFT
Step 1 - Up: Drive onto and stop in the middle of the platform. Apply the brakes of your chair or scooter.
Step 2: Verify that the emergency stop button is not activated by giving it a quick pull on the stop button.
Step 3: Press and hold the UP rocker. The lift will move in the up direction and stop when it reaches the upper landing.
Step 4: Release the brakes on your chair or scooter and drive off the platform.
WarningAlways verify the lift’s platform has stopped level with the upper landing. If not contact your AmeriGlide Dealer for assistance.
22 // 32 Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
Step 1 - Down: Drive onto and stop in the middle of the platform. Apply the brakes of your chair or scooter.
Step 2: Verify that the emergency stop button is not activated by giving it a quick pull on the stop button.
Step 3: Press and hold the DOWN rocker. The lift will move in the down direction and stop when it reaches the lower landing.
Step 4: Release the brakes on your chair or scooter and drive off the platform.
WarningAlways verify the lift’s platform has stopped level with the upper landing. If not contact your AmeriGlide Dealer for assistance.
23 // 32Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
90 V
DC
Mot
orU
pTo
p Lm
t
UP
A1
A2
Dow
n
DN
A1
A2
VA
CV
AC
24
Top
Inte
rlock
Sol
enoi
d
Fina
l Lm
tCN
C
110
Key
Sw
itch
SA
FA
1A
2
Em
erge
ncy
Sto
pS
AF 2
1
Saf
ety
Pan
Sw
itche
s
CN
CC
NC
CN
CC
NC
110 VAC
2
3
8
4
10
11
1
12
13
DN
2221
UP
2221
15 A
mp
C.B
.3
Am
pC
.B.
Top
Gat
eC
lose
d
6
7
CN
O
Btm
Gat
eC
lose
d
CN
O
CN
C Btm
Lm
t
Btm
Inte
rlock
Sol
enoi
d9
Btm
Doo
rLo
cked
Byp
ass
Top
Doo
rLo
cked
Byp
ass
5
+ -6V
DC
UP 3
4
RED
BLK
Bel
t Mon
itor
CN
O
CN
C
NO
NO
14 15 16
L1L2
G
4Te
rmin
al S
trip
Con
nect
ion
Sw
itch
- N.C
.
Sw
itch
- N.O
. hel
d cl
osed
Pus
h B
utto
n
Con
tact
- N
.O.
Con
tact
- N
.C.
Circ
uit B
reak
er
Lege
nd:
Opt
iona
l Equ
ipm
ent
Cal
l Sen
d
NO
NO
NO
NO
C C
C C
UP 2
1
DN 1
2
-15VSig+15V
L2 L1
90V
DC
Out
put
12A
Reg
en D
rive
TachComEN
DN 3
4
+ -~
~
17 6 1213
Opt
iona
l Wire
less
Cal
l-Sen
ds
98
NO
CO
M
A1
A2
NO
C
NO
C
NO
CO
M
A1
A2
Opt
iona
l Aut
o D
oor
Ope
ner R
elay
s
Top
Btm
Land
ing
Sw
itch
Land
ing
Sw
itch
To D
oor
Ope
ner
To D
oor
Ope
ner
12 13
CN
CC
NC
Pit
Sw
itchC
NC (O
ptio
nal)
Opt
. Flo
wS
witc
h
1
BB
AA
44
33
22
11
4423
1 RE
V F
SCH
EMAT
IC, C
PL A
C, 2
-STO
P
24 // 32 Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
VA
CV
AC
2411
0
15 A
mp
C.B
.
3 A
mp
C.B
.
90 V
DC
Mot
or
BR
AK
E
Cal
l Sen
d
NC
NCNO
NC
Em
erge
ncy
Sto
p
Pla
tform
Con
trol
CN
CC
NC
CN
CC
NC
Saf
ety
Pan
LowerLimit
UpperLimit
FinalLimit
Trav
el C
able
#44
042
/ 43
/ 44
Saf
ety
Nut
HR
NS
#44
011
Cal
l Sen
d #4
9300
NO
C
NO
SO
L
Gat
eC
lose
d
C
NO
SO
L
Gat
eC
lose
d
Opt
iona
lP
hone
Jack
Opt
iona
lP
latfo
rmG
ate
Opt
iona
lTo
p La
ndin
gG
ate
Opt
iona
lLi
ghte
dA
larm
Cal
l Sen
d
NC NO
NC
LowerBypass
UpperBypass
NO
Opt
iona
l Top
or B
otto
mE
lect
ric D
oor S
trike
Opt
iona
l Top
or B
otto
mE
lect
ric D
oor S
trike
1 2 3 4 6 7 8 95 1 2 1 2 3 4 65 1 2 3 4 65 1 2 3 4 6 7 8 95
1 2 3 4 65
1 2 3 1 2 3 1 2 3 4
1 2
12 3 46 5 1 2 3 1 2
-15V
Sig
+15V
L2
L1
90VDC Output
12A
Regen Drive
Tach
ComEN
NO
Bel
tM
onito
r
C
NC
SO
L
Doo
rC
lose
d
Doo
rLo
cked
C
NC
Pow
erM
odul
e1
AC AC
DC
+
DC
-
AC AC
DC
-
DC
+
1 1
Ele
ctric
Stri
ke P
ower
Opt
. Flo
atS
witc
h
BB
AA
44
33
22
11
4423
1 RE
V F
WIR
ING
DIA
GRA
M, C
PL A
C, 2
-STO
P
25 // 32Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
90
VD
CM
oto
r
Up
To
p L
mt
UP
A1
A2
Do
wn
DN
A1
A2
VA
CV
AC
24
Top I
nte
rlock
Sole
noid
Fin
al L
mt
CN
C
11
0
Ke
yS
witch
SA
FA
1A
2
Em
erg
en
cyS
top
SA
F 21
Sa
fety
Pa
n S
witch
es
CN
CC
NC
CN
C
CN
C
110 VAC
2
3
8
4
10
11
1
12
13
DN
22
21 U
P
22
21
15
Am
pC
.B.
3 A
mp
C.B
.
To
pG
ate
Clo
sed
6
7
CN
O
Btm
Ga
teC
lose
d
CN
O
CN
C Btm
Lm
t
Btm
Inte
rlock
Sole
noid
9
Btm
Do
or
Lo
cke
d
Byp
ass
- 3
, 4
To
p D
oo
rL
ocke
d
Byp
ass
- 1
, 2
5
+ -6V
DC
UP
34
RED
BLK
Be
lt M
on
itor
CN
O
CN
C
NO
NO
L1
L2
G
4T
erm
inal S
trip
Connection
Sw
itch -
N.C
.
Sw
itch -
N.O
. held
clo
sed
Pu
sh B
utton
Conta
ct -
N.O
.
Conta
ct -
N.C
.
Cir
cuit
Bre
aker
Legend:
Op
tion
al E
quip
ment
NO
NO
NO
NOC C
C C
UP
21
DN
12
-15V
Sig+15V
L2
L1
90
VD
C O
utp
ut
12
A
Re
ge
n D
rive
TachComEN
DN
34
+
-~
~
Mid
14
Mid
Inte
rlock
15
Byp
ass
NO
C
Mid
Ga
teC
lose
d
CN
O
164 3 2 1
8 7 6 5
Mid
Lm
t
CN
CC
NC
CN
C
Pit S
witch
(Op
tio
na
l)
Op
t. F
loa
tS
witch
BB
AA
44
33
22
11
SCALE
~±
1±
0.0
10
± 0
.02
± 0
.1
FRO
M D
RAW
ING
.-
DO
NO
T M
EASU
RE
AN
GLE
S
-
.X
XX
.X
XD
ECIM
ALS
.X
TO
LERAN
CES A
RE:
DIM
EN
SIO
NS A
RE I
N I
NCH
ES.
UN
LESS O
TH
ERW
ISE S
PECIF
IED
PER
ASM
E Y
14.5
- 2
009
INTER
PR
ET D
RAW
ING
AN
D T
OL
WIT
HO
UT W
RIT
TEN
CO
NSEN
TN
OT T
O B
E C
OPIE
D O
R U
SED
CO
NFID
EN
TIA
L IN
FO
RM
ATIO
N
REV E
2 O
F1
SH
EET
BSIZ
E
5/1
0/2
010
DF
DATE
DRAW
N B
Y
DESCRIP
TIO
N
44331
DW
G N
O.
SCH
EM
ATIC
, CPL A
C, 3-S
TO
P
20-A
pr-
15
MN
REF E
CO
-001149
AD
DED
OPTIO
NAL F
LOAT S
WIT
CH
;
E29/M
AR/1
8BK
INFO
RM
ATIO
N. R
EF E
CO
-003048
CO
RRECTIO
NS A
ND
AD
D C
ON
NECTO
R
D
DATE
CH
KBY
DESCRIP
TIO
NR
EV
REVIS
ION
HIS
TO
RY
1 2 3
TO
P C
ALL
MID
CALL
BO
TTO
M C
ALL
Ca
ll S
tatio
n
1 2 3
Ca
ll S
tatio
n
13
1 2 3
Ca
ll S
tatio
nT
BD
LS
-2T
RA
VE
L-4
,L
S-1
Mid
Inte
rlock
A1
A2
Inte
rlo
ckS
ole
no
id
WH
ITE
Do
or
Lo
cke
d
Do
or
Clo
sed
DN
51
52
UP
51
52M
id I
nte
rlo
ck
- 2
Mid
In
terlo
ck -
1
To
UP
- 5
2
Byp
ass
NO
C
Top
Inte
rlock
A1
A2
Inte
rlo
ckS
ole
no
id
WH
ITE
Do
or
Lo
cke
d
Do
or
Clo
sed
1 2 3 41223 5
4
8 7 35
Byp
ass
NO
C
Btm
Inte
rlock
A1
A2
Inte
rlo
ckS
ole
no
id
WH
ITE
Do
or
Lo
cked
Do
or
Clo
sed
8 7 212
BYPASS S
EE T
OP A
ND
BTM
INTERLO
CKS
Fie
ld W
irin
g
1 2 3 4 65
Tra
velin
gC
ab
le
12 6 713
7 98
5 14
15
16
LS-1
Bla
ck
Wh
ite
Gre
en
Blu
e
Re
d
Se
e In
terl
ock
Co
nn
ect
ors
7
To
Mid
Inte
rlo
ck -
4F
rom
Top
Inte
rlo
ck -
3
To
Btm
Inte
rlo
ck -
46
Fro
m M
idIn
terl
ock
- 3
SM
SCHM
ATIC
, CPL
AC
3-ST
OP44
331
REV
E
26 // 32 Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518BB
AA
44
33
22
11
SCALE
~±
1±
0.0
10
± 0
.02
± 0
.1
FRO
M D
RAW
ING
.-
DO
NO
T M
EASU
RE
AN
GLE
S
-
.X
XX
.X
XD
ECIM
ALS
.X
TO
LERAN
CES A
RE:
DIM
EN
SIO
NS A
RE I
N I
NCH
ES.
UN
LESS O
TH
ERW
ISE S
PECIF
IED
PER
ASM
E Y
14.5
- 2
009
INTER
PR
ET D
RAW
ING
AN
D T
OL
WIT
HO
UT W
RIT
TEN
CO
NSEN
TN
OT T
O B
E C
OPIE
D O
R U
SED
CO
NFID
EN
TIA
L IN
FO
RM
ATIO
N
REV E
2 O
F2
SH
EET
BSIZ
E
5/1
0/2
010
DF
DATE
DRAW
N B
Y
DESCRIP
TIO
N
44331
DW
G N
O. SCH
EM
ATIC
DIA
GR
AM
, CPL
AC, 3-S
TO
PFIE
LD
IN
STALLED
EQ
UIP
MEN
T
98
1
NO
CO
M
A1
A2
NO
C
NO
C
NO
C
Mid
Call
Sta
tion
NO
CO
M
A1
A2
NO
CO
M
A1
A2
Do
or
Op
en
er
Re
lays To
p
BtmMid
La
nd
ing
Sw
itch
La
nd
ing
Sw
itch
La
nd
ing
Sw
itch
To
Do
or
Op
en
er
To
Do
or
Op
en
er
12
13
UP
62
61
DN
62
61
5
Mid
Inte
rlock
Inte
rlock
Sole
noid
ELE
CTRIC
STRIK
E W
IRIN
G46067, 46068 B
lack
Bla
ck
White
White
NO
C
NC
DO
OR O
PEN
ER
WIR
ING
Von D
uprin
Folg
er
Adam
s
Mid
Inte
rlock
Inte
rlock
Sole
noid
NO
C
NC
Bla
ck
Bla
ck /
White
White
Blu
eN
O
C
NC
Trine
Ora
nge
Bro
wn
Blu
e
Bla
ck /
White
Gre
en
Yello
w
Gre
y
Ora
nge
NC
Mid
Inte
rlock
Inte
rlock
Sole
noid
NO
C
NC
Bla
ck
Bla
ck /
White
White
NO
C
NC
Ora
nge
Bro
wn Blu
e
Bla
ck /
White
Bro
wn
Gre
y
Ora
nge
NC
White
Vio
let
NO
C
NC
Mid
Inte
rlock
Inte
rlock
Sole
noid
C
NC
Bla
ck
Door
Clo
sed
White
C
NC
Ora
nge
Bro
wn
Blu
e
SO
LE
NO
ID C
ON
TR
OL
NO
C
C
NC
EM
I In
terlock
Door
Lock
ed4621, 4622
A B C D
NC
Yello
w
SCHE
MAT
IC D
IAGR
AM, C
PL A
C3-
STOP
4433
1 RE
V E
27 // 32Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
1 1
2 2
3 3
4 4
AA
BB
NC
C
C
CH
AR
GE
RBA
TTER
Y
MO
TOR
SPEE
D
NO
C
CC
ON
TRO
L
NO
CN
OC
NO
-C
NO
NC
12 V
DC
24 V
DC
NC
C
G
PWM
NC
+
+12V
+M
C
NC
C
NC
C
12 V
DC
NO
NC
CC
CN
CC
NC
NC
NC
NC
-
+
NO
CC
-M
Brak
e
Mot
or
15 16
REDBLK
24VD
C
Bel
t Mon
itor
Cal
l Sen
d
24VD
C
Up
Top
Lmt
Dow
n
Fina
l Lm
t
Key
Sw
itch
(OPT
ION
AL)
Emer
genc
yS
top
4
Key
Sw
itch
(OP
TIO
NAL
)
Term
inal
Stri
p C
onne
ctio
n
Safe
ty P
an S
witc
hes
2
3
8
4
10
11
1
Sw
itch
- N.C
.
Sw
itch
- N.O
. hel
d cl
osed
Push
But
ton
Con
tact
- N
.O.
Con
tact
- N
.C.
7
7 7
Circ
uit B
reak
er
Lege
nd:
30 A
mp
3 A
mp
Top
Gat
eC
lose
d
6
7
(Opt
iona
l)Pi
t Sw
itch
Btm
Gat
eC
lose
d
Btm
Lm
t
9
Btm
Doo
rLo
cked
Byp
ass
Braking Resistor
Top
Doo
rLo
cked
Byp
ass
5
+ -6V
DC
Opt
iona
l Equ
ipm
ent
14
12
13
34
8
68
3
4
DN
U2
UP
DN
UPDN
Top
Inte
rlock
Btm
Inte
rlock
A1
A2
Sole
noid
A1
A1
D2
A1
DN
A2
A2
U2
UP
SAF
SAF
Sole
noid
U2
D2
D2
A2
A1
6
UP
SCHE
MAT
IC, C
LP D
C2-
STOP
4414
1 RE
V F
28 // 32 Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
1 1
2 2
3 3
4 4
AA
BB
24 V
DC
Mot
or
50W-3Ω
Opt
iona
l Top
or B
otto
mE
lect
ric D
oor S
trike
BR
AKE
NC
NO
Belt
Mon
itor
Cal
l Sen
d
NC
NCNO
NC
Em
erge
ncy
Sto
p
Pla
tform
Con
trol
CN
CSa
fety
Pan
X6
LowerLimit
UpperLimit
FinalLimit
Trav
el C
able
#44
042
/ 43
/ 44
Plat
form
Con
trol
#49
218
Cal
l Sen
d #4
9300Gat
e C
all
Sen
d H
RN
S#4
4012
Limit Sw
itch HR
NS #44007
NO
C
NO
SO
L
Gat
eC
lose
d
C
NO
SO
L
Gat
eC
lose
d
Opt
iona
lP
hone
Jack
Opt
iona
lP
latfo
rmG
ate
Opt
iona
lTo
p La
ndin
gG
ate
Opt
iona
lLi
ghte
dA
larm
Cal
l Sen
d
NC NO
NC
LowerBypass
UpperBypass
NO
Opt
iona
l Top
or B
otto
mE
lect
ric D
oor S
trike
1 2 3 4 6 7 8 95 1 2 1 2 3 4 65 1 2 3 4 65 1 2 3 4 6 7 8 951 2 3 1 2 3 1 2 3 4
1 2
12 3 46 5 1 2 3 1 2
SO
L
Doo
rC
lose
d
Doo
rLo
cked
1 2 3 4 65
WIR
ING
DIAG
RAM
, CPL
DC
2-ST
OP44
141
REV
F
29 // 32Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
1 1
2 2
3 3
4 4
AA
BB
Up
Top
Lmt
UP
A1A
2
Dow
nD
NA1
A2
Top
Inte
rlock
Sol
enoi
d
Fina
l Lm
t
NC
Key
Sw
itch
SAF
Em
erge
ncy
Stop
4Te
rmin
al S
trip
Con
nect
ion
Saf
ety
Pan
Sw
itche
sN
CN
CN
CN
C
2
3
8
4
10 11
1
12
13
Switc
h - N
.C.
Switc
h - N
.O. h
eld
clos
ed
Push
But
ton
Con
tact
- N
.O.
Con
tact
- N
.C.
Circ
uit B
reak
er
Legend
:
30 A
mp
Top
Gat
eC
lose
d
6
7
NO
Btm
Gat
eC
lose
dNO
NC B
tm L
mt
Btm
Inte
rlock
Sol
enoi
d9
Btm
Doo
rLo
cked
Bypa
ss
Top
Doo
rLo
cked B
ypas
s
5
+ -6V
DC
Bel
t Mon
itor
NO
Opt
iona
l Equ
ipm
ent
NC
NO
NO
14 15 16
U2
A1A
2 D2
A1A
2
SAF
D2
D2 + +
12 V
DC
BATT
ERY
CH
ARG
ER
24 V
DC
--
12 V
DC
24V
DC
BR
AK
E
NO
NO
NO
NO
Mid
4 3 2 1
8 7 6 5M
id L
mt
Mid
Inte
rlock
Sol
enoi
d
Cal
l Sta
tion
Up
Mid
Dow
n1312
6 6 6
Mid
Gat
eC
lose
dNO
24VD
CM
otor
3 A
mp
DN
UP
DN
UP
RED
DN
UP
BLK
7
7 7 7A1
NC
Pit
Sw
itch
NC
NC
A2
Mid
Doo
rLo
cked
Byp
ass
NO
NO
1312
1
NO
CO
M
A1A2
NO
C
NO
C
NO
CM
id C
all
Sta
tion
NO
CO
M
A1A2
NO
CO
M
A1
A2
Doo
r Ope
ner
Rel
ays
Top
Btm
Mid
Land
ing
Switc
h
Land
ing
Switc
h
Land
ing
Switc
h
To D
oor
Ope
ner
To D
oor
Ope
ner
To D
oor
Ope
ner
8 9
4
3
86
U2
U2
4
3
86
WIR
ING
SCHE
MAT
IC, C
PL D
C3-
STOP
640-
0000
5 RE
V A
30 // 32 Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
• Parts used that are not approved by AmeriGlide • Labor fees for installation work, repair or service calls are not covered• Outdoor installation within 1 mile of a coastline reduces warranty
to 180 days and expressly excludes rust after 30 days. Warranty is extended to 2 years with Premium Protection Option.
• Due to the nature of steel construction being permanently placed in an outdoor environment and its inherent unpredictability, minor paint defects and cosmetic rust are not covered after 30 days by AmeriGlide’s Limited Warranty.
• AmeriGlide enclosures, when used, are designed to protect a CPL and its users from being directly affected by the elements.It is NOT intended nor designed to be completely water proof.
Effective August 1, 2017 TEC 2006 P/N: CSVF-000016 Rev B
Phone: Email:
Hercules II CPL– TWO YEAR WARRANTY CERTIFICATE
LIMITED WARRANTY CERTIFICATEProducts Covered: HERCULES II
PLEASE FILL OUT ALL FIELDS AND RETURN WITHIN TEN (10) DAYS OF PRODUCT INSTALLATION. Mail to AmeriGlide, 2075 47th Street, Sarasota, FL 34234. AmeriGlide warrants to the original purchaser of a Hercules Commercial Vertical Platform Lift (CPL) manufactured by us to be free from defects in material, mechanical and electrical components (parts) for a period of two (2) years, provided that the products have been installed, maintained and operated properly according to the AmeriGlide Installation and Owner’s Manuals.
EXCEPTIONS TO THIS LIMITED WARRANTY ARE: PLEASE READ CAREFULLY
• AmeriGlide CPL’s and EPL’s installed outdoors must include the Premium Protection Package to maintain 2-year warranty; otherwise warranty is limited to one (1) year.
• Batteries are limited to one (1) year with a AmeriGlide supplied/approved charger.
• Damage resulting from improper installation or operation• Additional parts/labor related to code compliance that were not
identified on the original order• Negligence, alterations, abuse or misuse of the equipment • Fire, flood, acts of God • Shipping damage
This warranty starts on the date of initial product installation (not to exceed 90 days from the date of manufacture), provided the warranty certificate is completely filled out and returned to AmeriGlide within ten (10) days of installation. AmeriGlide and its dealers shall not be liable for any consequential, special or incidental damages arising out of the purchase or use of the unit or resulting from the breach of this Limited Warranty, or any implied warranty. The limit of liability of AmeriGlide and its dealer hereunder shall be the unit’s purchase price. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, or legal remedies, so these above limitations may not apply to you. All warranty claims must be reported to the dealer from whom the lift was purchased as they have responsibility for handling your warranty claim. The dealer is to contact the Technical Services Department of AmeriGlide and provide the serial number of the product along with a description and evidence of the defect(s) supporting a warranty claim. Dealers may charge for labor, service, travel, or other associated costs to make repairs, and such charges are not covered by this Limited Warranty. It is permissible to have any repairs or replacement work done as a result of any defects in material and workmanship by someone other than the Dealer under this Limited Warranty. However, the Limited Warranty does not cover any charges or expenses assessed by any such other person or company performing such repairs or replacement work. All parts used to replace defective materials must be genuine AmeriGlide parts to be covered by this Limited Warranty. This Limited Warranty gives you specific legal rights, and you may have other rights which vary from state to state. AmeriGlide will not be charged for labor, consequential damage or repair expenses. AmeriGlide will not, under any circumstances, be liable for the loss of the use of its products or loss of time. Defective parts must be returned, if requested, prepaid, to AmeriGlide for inspection prior to credit or replacement. At AmeriGlide’s discretion, any part found to have been modified, over-stressed, damaged by accident, or misused is not covered by this warranty. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, INCLUDING ALL IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION OF THE LIMITED WARRANTY DESCRIBED HEREIN.
PRODUCT INFORMATION: PURCHASER INFORMATION:Model: Name: Premium Protection Package: Yes No Mailing Address:Serial Number: Installation Address (if different):Date of Installation: Type of Installation: Indoor Outdoor
Residential CommercialDEALER/INSTALLER INFORMATION ADDITIONAL INFORMATION:Company Name: How did you hear about AmeriGlide?Installer Name: Dealer Internet Magazine Friend/Family OtherAddress:
Phone: Style Dealer Own Other AmeriGlide Product Ease UseE-Mail: Recommendation Price/Value Key Feature
I selected AmeriGlide due to its (select all that apply):
31 // 32Hercules II 750 Vertical Platform Lift Manual | www.Ameriglide.com | 866-378-6648
P/N: 630-00046 RevD 111518
NOTES:
P/N: 630-00046 RevD 111518