installation manual of spring recessed panel paduan aplikasi dengan … · 2018-01-17 · pastikan...
TRANSCRIPT
2015/01-1
1. Please check the fitting bag with components list
2. Mark the drilling holes on the ceiling according to the sketch
Make sure the holes in the correct positions
3. Fix the 4 Upper fixing base onto ceiling with expansion screws and screws
4. Assembling the Suspension accessory according to the pictureMake sure the steel wire rope hanging the same size
5. Connect the driver
Installation Steps
Harap diperiksa apakah komponen part yang ada dalam packing lengkap
Beri tanda pada lubang pengeboran di ceiling laingit sesuai yang diinginkanPastikan lubang-lubang di posisi yang benar
PADUAN APLIKASI DENGAN MENGGANTUNG Installation Manual of Suspension Led Panel Light
Pasang 4 siku hanging brackets di lampu panel dengan baut dan kencangkan
Rakit aksesoris gantung dan kawat sesuai contoh pada gambar Pastikan tali kawat baja di gantung sama ukurannya
Terakhir koneksikan dengan driver
Recessed In T-Bar Ceolong FramePADUAN APLIKASI DI CEILING
Installation Steps
1. Remove the gypsum board from the T-bar ceiling
2. Tilt the panel light up the T-bar frame and turn the panel into the right position
3. Put the panel front adown, and check if it is fixed into the ceiling channel
Installation Manual of Spring Recessed PanelPADUAN APLIKASI DENGAN BAUT
! ATTN: Before installation, the driver can be put aside the T-channel, It can not put at the backside of the panel light. Connect the driver according to wiring diagram.
! PERINGATAN: sebelum instalasi, driver bisa ditempatkan di dalam ceiling. Jangan menempatkan driver di atas lampu panel. Koneksikan driver sesuai dengan cable diagram.
1. Please check the fitting bag with components list.
2. According to the specification sheet as below, juding if the ceiling meets the installtion requirements of spring recessed.
persyaratan penggunaan aplikasi dengan clip.
SpecPanel Size (mm)
External Size of T-channel (mm)
N.W (KG)
! ATTN: Make sure the dimension of cut-out match the size of panel light. The thickness of ceiling should be 1-2 cm.
! ATTN: Make sure the ceiling is strong enough for load bearing, otherwise the panel may fall down. ! PERINGATAN: Pastikan ceiling langit cukup kuat untuk menahan beban lampu panel,
jika tidak panel akan jatuh.
3. Pull up the springs at one side of panel to fix inside the edge of T-channel.
4. Pull up the springs at another side and push up the panel to fix the springs inside the ceiling.
5. Check the panel light and adjust the panel position to cover the whole cut-out,and make sure it is in the central place.
! PERINGATAN: pastikandimensi cut-out sesuai dengan perbandingan ukuran lampu panel. Ketebalan langit–langit antara 1-2 CM.
3030
3060
30120
6060
60120
296±1(L)*296±1(W)
296±1(L)*596±1(W)
296±1(L)*1196±1(W)
596±1(L)*596±1(W)
596±1(L)*1196±1(W)
275±3(L)*275±3(W)
275±3(L)*575±3(W)
275±3(L)*1175±3(W)
575±3(L)*575±3(W)
575±3(L)*1175±3(W)
1.5
2.8
4
4
7.5
Pindahkan papan gipsum yang akan ditempatkan panel light dari T-bar langit-langit
Miringkan lampu panel atas T-bar frame dan mengubah panel ke posisi yang tepat
Letakkan sisi panel depan ke arah bawah, dan periksa apakah terpasang dengan tepat di ceiling langit-langit
Harap diperiksa apakah komponen part yang ada dalam packing lengkap.
Menurut lembar spesifikasi sebagai berikut, menilai apakah ceiling sesuai untuk
Tarik clip di satu sisi panel untuk masuk ke dalam ceiling.Tarik clip di satu sisi panel lainnya dan dorong lampu panel untukmasuk sesuai ke dalam ceiling.
Cek lampu panel dan adjust posisi lampu panel sesuai cut–out, pastikan posisi di tengah cut out.