installation manual for the application ihc-marf...thanks to ihc-marf (the "application"),...
TRANSCRIPT
Rev.:200214 Page 1 of 16
Installation Manual iHC-MARF
Installation Manual for the application iHC-MARF
Rev.:200214 Page 2 of 16
Installation Manual iHC-MARF
Contents 1. Introduction ............................................................................................................................................................................ 3
2. Installing the application on a mobile telephone with OS Android via the service Google Play ............. 3
3. Installing the application on a mobile telephone with OS Android from a file .............................................. 4
4. Settings ..................................................................................................................................................................................... 5
5. Control ..................................................................................................................................................................................... 13
Rev.:200214 Page 3 of 16
Installation Manual iHC-MARF
1. Introduction
The application iHC-MARF (for mobile phones with OS Android) is designed for comfortable control of the RF Control electrical installation using your mobile telephone. This is an RF Control system accessory, and as a part of the iNELS Smart Home Solution, its elegance blends perfectly with any modern home. The menu is divided into clearly structured sections in which the icons indicate individual functions. Here you will also find faster access to your favorite functions, and you will maintain a constant clear view of what's happening in and around your home.
Thanks to iHC-MARF (the "application"), you can perfectly control the function of your wireless RF Control electrical installation. You thus keep complete control over your home lights, appliance switching and heating.
The application only works with the device eLAN RF-003 or eLAN RF-Wi-003. This element must be used in your wireless installation.
It is designed for devices with OS Android 2.4 and higher.
It is optimized for devices with a resolution display of 800x480
The application language follows the language set in the OS Android
Implemented communication with Axis video cameras, thanks to which you can monitor what's going on around your home.
It also enables control for multiple users at once (by entering multiple IP addresses).
It does not enable creation of week-long programming or communicating with temperature actuators.
Downloading Download the current version at Google Play (under the name iHC-MARF). https://play.google.com/store/apps/details?id=cz.elkoep.ihc_marf&hl=cs Installing the application on the device
2. Installing the application on a mobile telephone with OS Android via the service Google Play
a) Connect to the Internet using the mobile telephone. b) Activate the service Play Store or Google Play. c) In the search bar, enter the password "iNELS" and press
"Search". d) Select the application "iNELS Home Control RF Mobile"
from the list and open the dialog field with information on this application.
e) Click on "Install". A message is displayed on permission to access the telephone services. These services are conditional for installing the application. Thus, tap "Accept".
f) On the display, first a downloading bar graph appears indicating that the application is downloading to the phone, followed by an installation notification.
Rev.:200214 Page 4 of 16
Installation Manual iHC-MARF
g) After the application is successfully installed in the phone,
instead of the button "Install", the buttons "Open" and "Uninstall" appear.
h) Installation is complete, go to the "Applications" tab where the
icon is located and open the application. hjadvf
3. Installing the application on a mobile telephone with OS Android from a file
a) The application can also be installed on a mobile telephone from a file. The application can be downloaded to the PC or the telephone into the given file system.
b) Using the mobile telephone and tool "File manager", search for the stored application iHC-MARF in the file system within the given directory.
c) By clicking on the file with the application iHC-MARF.apk, the operating system starts installing the application from the file.
d) Prior to the actual installation, the OS will ask about access to the provided services necessary for running the application, and displays the "Install" button.
e) Once the installation is complete, the OS indicates this and directly offers you to open the installed application iHC-MARF.
Rev.:200214 Page 5 of 16
Installation Manual iHC-MARF
4. Settings
Initial display upon running the application. by pressing the "Settings" button, you bring up the application's basic settings menu.
The aim of using the application for controlling the installation is so that after running, it immediately offers control of the electrical installation. To achieve this with the least amount of presses and so that everything required would be offered right from the home desktop, you must first set up and configure the application.
a) Tab "Settings"
Selection for the basic configuration of the
application and device, ELAN-RF(Wi)-003 device
settings. Configuration of the project of the
installation, assigning addresses, pairing
Setting the IP address of the communication interface,
by means of which the telephone communicates with the wireless elements
(ELAN-RF-003, or ELAN-RFF-.WI-003).
Selection for setting the tab "Scenes"
Selection for setting the tab "Video cameras"
Selection for setting the tab "Favorites"
Tab "Scenes"
The home application desktop.
After configuring, the basic "tiles" of the control system
are displayed.
"Help" button
Basic upper bar of the telephone Tab "Video cameras"
Tab "Favorites"
Tab "Settings"
Rev.:200214 Page 6 of 16
Installation Manual iHC-MARF
b) Tab "IP settings"
Upon initial configuration, select the "Add" button displayed on the screen. After clicking, you will see the display IP Settings as shown below.
After clicking on save, the application moves to a list of set devices. For the application to run, it is necessary to check the given eLAN, with which the application is to communicate primarily. In this device list, you can have several devices and IP addresses configured. Here you can have one and the same eLAN, but with e.g. two IP addresses, with an internal IP address in a home network, and with a public address for remote communication from anywhere on earth.
c) Configuration - floor plan
Button for adding a floor plan
Field for the selectable name "Naming" the eLAN device in the installation
Field for setting the communication port of the eLAN device: default port
80.
Field for entering the IP address of the device eLAN-
RF-003 address
Rev.:200214 Page 7 of 16
Installation Manual iHC-MARF
After clicking on "Add", you can add any image you like from your telephone that you later want to have displayed e.g. in the TV application.
Though the floor plan that you select upon creating the room will not be displayed in your telephone application, it is necessary to enter it when creating the room.
Rooms
You can name the rooms as you like by entering your chosen name into the room name field. Choose the type of room based on which icon best fits your needs for the room.
If you only create one room, the device is displayed directly on the desktop.
Window for entering the room name
Window for entering the room icon
Window for adding a previously saved
floor plan
Window for displaying the
selected floor plan
Button for saving the selected room
Rev.:200214 Page 8 of 16
Installation Manual iHC-MARF
d) Devices - adding RF actuators
To add a device that you want to control via the application, just fill in the four fields based on the image and save.
Then after clicking on the device icon, the added device will be displayed.
If you want to remove the device, press and hold it until the device disappears. If you only want to rename the device or perform any other modification, tap on it shortly to open its settings.
Button for saving the added device
Here you enter any name of the device you are controlling
Window for writing in the address of the added actuator (e.g.001a2b)
Window for selecting the type of actuator
Window for selecting the type of device
Added device that can be modified
Rev.:200214 Page 9 of 16
Installation Manual iHC-MARF
After adding rooms and all devices, you must still assign the devices to the rooms in which they are found, which of course is not a condition, and you can add devices anywhere, e.g. in all rooms. You can do this by clicking on the "Assign" button, where you select the room into which you want to assign the device. Then by tapping the confirmation buttons, you select which elements will be in the given room.
If you've selected a device for a desired room, continue by pressing the "Next" button in the lower right corner for displaying the confirmation screens, where you will confirm the added device by pressing "Save". Do the same to change added devices, with the difference that you are only changing the status of the confirmation buttons when selecting the device.
Selection of the room for adding
the device
Confirmation button upon selecting the
device
Next button for continuing and consequent saving
Rev.:200214 Page 10 of 16
Installation Manual iHC-MARF
e) Tab "Favorites" After pressing, the application desktop appears with the buttons "Next" and "Add". After pressing "Add", a list of configured devices opens, which by checking the selection automatically, then after pressing Save, it is assigned automatically to the list in the "Favorites" tab.
f) Tab "Scenes" The list of scenes is used to activate the user's predefined scenes, such as all off, all on, all blinds up, all blinds down, etc. Upon initial configuration, select the "Add" button displayed on the screen. After clicking, you will see the display IP Settings as shown below.
List of all devices configured in eLAN RF-003. Checkbox for
selecting the device in the
"Favorites" tab
Button for saving the "Favorites" tab
configuration
Checkbox for selecting from all used devices for
configuration in the "Scenes" tab
"Next" button for selecting the device,
switches to the display for setting the
action on selected devices.
Field for basic naming of
configured scene
Rev.:200214 Page 11 of 16
Installation Manual iHC-MARF
g) Tab "Video cameras"
If you wish to have video cameras closer "at hand", you can add video cameras to the quick display - Tiles. In the iHC application, you can also view the current image (stream) from home security Axis IP video cameras. Upon initial configuration, select the "Add" button displayed on the screen. After clicking, you will see the display with Axis IC camera settings as shown below. The application allows full screen video camera display, and bringing up the PTZ panel for its control is performed by pressing and holding the relevant video camera view
Defined naming of the configured scene
Scroll bar of selected devices in the created
scene. Primarily, the devices is selected at the middle position of the scroll bar - under the scene
name. Setting the event for a dimming actuator,
where you set the required brightness, which is set on the
actuator if a scene is brought up.
Field indicating the selectable "name" of the IP
video camera
Video camera type field, here with the selection field from the Axis manufacturer
default menu
Field for displaying the IP address of the installed
video camera
Field for entering the log-in password to the added IP
video camera.
Field for entering the log-in name to the added IP video
camera.
Rev.:200214 Page 12 of 16
Installation Manual iHC-MARF
After filling in all the required fields on the display, press Save. The application saves the settings and automatically adds the video camera to the list of devices in the "Video cameras" tab If you want to permanently delete the camera from the list, press and hold the given list item.
"Video cameras" tab with defined video cameras and video
camera view in the tile position on the desktop.
PTZ control elements
Clicked tile of the defined IP video camera in the iHC application.
The video image (stream) from the
security camera now automatically reverses
according to the telephone's approved
Rev.:200214 Page 13 of 16
Installation Manual iHC-MARF
5. Control
a) Tiles The main display in the iHC application is formed of so-called "Tiles". This is a general overview of elements, where you can see at first glance according to the icons, either backlit or not, the active icons in the iNELS Home Control intelligent electrical installation. Based on the previous step "configuration and settings", the initial display shows the application's default tiles, so that they are assigned according to elements in rooms (such as "Kitchen") or in groups (as seen on the display e.g. "Lights or All"). If you wish to go from displaying Tiles to displaying List, just click on the name of the tile, e.g. Lights, and a pop-up menu appears in the given tile ("rooms").
Tile "Kitchen"
Basic overview of configured tiles in the
Applications menu.
Button for configuring the system and settings from
the application
Tiles - if the configuration is set up that there are more than six tiles on the default display, moving between
them is performed by using your finger to drag the
display left or right
Rev.:200214 Page 14 of 16
Installation Manual iHC-MARF
If you press and hold your finger on individual devices, e.g. for a dimmed light, a bar graph appears for setting the brightness of the dimmed light. Two icons are displayed underneath it - brightness increase and decrease, enabling smooth dimming and brightening of your light. Using the arrows, you can open a menu where you can set the precise time of these functions, which you confirm by clicking on the settings icon. For switching actuators, you can run delayed on/off, and you can tap the arrows to adjust their times. The blinds actuators can be programmed the same way. The setting of one time for both directions applies to blinds actuators.
Status bar of monitored rooms or groups, - by using
your finger to drag and scroll left or right, you can switch between individual
groups, rooms, and thus see individual devices located
within each.
Tiles for individual devices in rooms, or a group
By dragging your finger on the display, you can scroll
up and down through tiles Actuator output status
indicator, or device switched on, off
Actuator output status indicator, or device
switched on - brightness at 50%. To bring up the
brightness setting, the slider must be held on the
actuator tile
Arrows for switching between rooms or groups
Symbol, icon assigned to the given actuator, device
Rev.:200214 Page 15 of 16
Installation Manual iHC-MARF
The time setting for shutter actuators works in both directions
Brightness setting
By pressing the button, you initiate Brightness increase
Setting the time of Brightness increase/decrease
Buttons for menu, time setting for the given
function
By pressing the button, you initiate Brightness increase
By pressing the button, you
initiate Brightness
Setting the time of Delayed off/on
By pressing the button, you
initiate Delayed
Rev.:200214 Page 16 of 16
Installation Manual iHC-MARF
By pressing and holding the RGB actuator, you will see the menu displayed for setting color, brightness and the brightening mode.
Setting the light RGB color
Setting the light RGB brightness
Switching off/on the RGB light
Currently selected color
"Circus" mode - automatic color
change
Setting duration for dragging the
blinds
Stopping movement of the
blinds
Open the blinds
Close the blinds