installation instructions vanity top
TRANSCRIPT
ALEUTIAN
INSTALLATION INSTRUCTIONS
VANITY TOPK-2746T-1/8
-1-, 2013
Copyright Kohler China Ltd., 2013
�
�
�
Observe all local plumbing and building codes.
Prior to installation, unpack the new lavatory and inspect itfor damage. Return the lavatory to its protective cartonuntil you are ready to install it.
All information in these instructions are based the latestproduct information available at the time of publication.Kohler China reserves the right to make changes inproduct characteristics, packaging, or availability at anytime without notice.
Make sure that the wall and floor are squareand plumb to ensure proper installation.IMPORTANT:
�
�
�
ORDERING INFORMATION
Aleutian Vanity Top...............................................K-2746T-1/8 .................................................K-2746T-1/8
REQUIRED MATERIALS/
(NOT SUPPLIED)
TOOLS
�
�
�
�
�
�
�
Level
Drill with bit6mm
14mm wrench
Framing square
Channel lock pliers
Tape measure
Pencil
�
�
�
�
�
�
�
6mm
14mm
ROUGHING-IN
UNIT: mm:
35
45
Reference Value
50
123
90 100
220
335
909
300
70
219
525
541
K-2746T-1
1196536-T01-A
Kohler reserves the right to change marked dimensions without prior notice.
Fig.#11
50
123
90 100
220
K-2746T-8
-2-
Install the Basin
NOTE! The lavatory tops must be installed on a cabinet or
matching metal stand (refer to Installation and User Guide
packed with the cabinet or stand for installation details).
Recommend Kohler metal square leg or Kohler bathroom
furniture for support or decoration.
�
(
)
�
�
76mm
� Rough-in the supplies and the drain piping.
The supply stop handles cannot extend more than
76mm from the finish wall when in the open position.
NOTE:
�
�
10mm
( )
65-
75mm
1. 2
2.
�
�
Drill two 10mm hanger bolt holes at the marks on the wall.
The nylon anchors is needed for concrete wall (supplied).
Mount hanger bolts to the wall so approximately 65-75mm
of each bolt remains exposed.
1. Height dimensions marked in fig. 2 could be
adjusted per your the vanity height or the actual
height of the console leg.
2. Other fastening devices of sufficient size and
strength may also be used.
NOTE:
Fig.#22
300mm
AttachmentBolt (x2)
Wall Plug
550m
m WasteOutlet
Waste
630m
m 805m
m
80mm
35 101.6101.6
335
909300
541
70
219
525
45
3X
1196536-T01-A
-3-
�� Install the faucet and drain to the lavatory according to the
manufacture's instructions.
�
�
�
�
� Carefully place the lavatory against the wall, so the
hanger bolts extend through the lavatory holes.
�
�
�
Level the lavatory.
Install the cap nuts and washers, and tighten until snug.
Do not
overtighten the cap nuts.Overtightening may cause
damage to the product.
Clean the lavatory top.
CAUTION: Risk of product damage.
�� Put the sealant around the back wall attached surface of
the lav evenly.
Apply Silicone sealantalong this face
WasherNut
Offset Nut
Fig.#33
1.
2.
3.
4.
Install the Plumbing
1. Install the drain in accordance with the manufacturer sinstructions.
Make sure a watertight seal exists on allbasin drain connections.
Provide access to the plumbingconnections for future plumbing maintenance.
2. Connect the hot and cold water supplies.
3. Open the hot and cold water valves, and check the supplyconnections for leaks.
4. Run water into the basin, and check the drain connectionsfor leaks.
CAUTION!
CAUTION!
,
Fig.#44
1196536-T01-A
-4-
IMPORTANT CONSUMER INFORMATIONIMPORTANT CONSUMER INFORMATION
CARE AND CLEANING
To keep your lavatory looking new, make sure you rinse it out
thoroughly after each use. on thisproduct, as they will scratch and ruin the surface. Stubbornstains, paint, or tar can be removed with turpentine or paintthinner.
Please do not use hard materials (likescouring pad) to clean product surface, especially theproduct logo.
DO NOT USE ABRASIVES
CAUTION:
CAUTION! Risk of product damage.
Many cleaners contain abrasive and chemical substances,and should not be used for cleaning stainless steel, enamel,plated or plastic fittings.
These finishes should be cleaned using a mild washing updetergent or soap solution, rinsed and then wiped dry with asoft clean cloth.
Do not use the product in the water below 0 C.o 0 C
o
SERVICE PARTSSERVICE PARTS
1034692Assy. Pack
Fig.#55
1196536-T01-A