installation instructions – integrated cd filter bag
TRANSCRIPT
Rev.1 / 09.2019
INSTALLATION INSTRUCTIONS – INTEGRATED CD FILTER BAG STORAGING CONDITIONS • The warehouse temperature should be max. 30° C (85° F), in this way premature shrinking is avoided
and installation becomes easier • Disc filter bags are made of polypropylene; material have to be covered from sunlight
DELIVERY INCLUDES: • Filter bag • Rubber sealing • Top hat • Acid proof staples
DELIVERY DOES NOT INCLUDE: • Stapler • Tightening clamp
F C85 30
MAX
Page: 1 (total 7)
Rev.1 / 09.2019
1. Place the bag on top of support wire
• Install Filter Bag on the sector carefully • Check that the side seam of the bag is in line with the sector edge – not twisted • Pull the filter bag downwards onto the sector and smooth out wrinkles and twist (this makes easier
the installation of the rubber sealing in the next step)
2. Install the rubber sealing and bag corner flaps carefully
• Install the rubber sealing on the upper edge of sector, ensuring that rubber goes evenly along the sector edge
• Fold the small fabric flap on top of the sealing rubber • Close the zipper about 100mm
Rev.1 / 09.2019
• Check that the rubber sealing has not slipped from its place • Ensure the rubber sealing under the zipper is smooth and straight • Fold the fabric flap at the corner underneath the zipper before closing it – pay attention to avoid
folds at the corner
3. Close the zipper
• When closing the zipper make sure the zipper closes straight and evenly • Finally check that rubber sealing lays properly in both ends and ensure that it has not slipped
aside when closing the zipper • Pull off the zipper tab completely
Rev.1 / 09.2019
4. The zipper ending
• Secure the zipper end with staples • Secure the zipper end with acid-proof staples; staples should be in X-form in order to get the best
locking • Make sure that staples do not cause holes in the bag material
5. Tighten the bag by pulling all the loose fabric downwards
• Carefully tighten all extra cloth to the lower part of the bag • This ensures a tighter bag after shrinking
Rev.1 / 09.2019
6. Attach the tightening clamp to sector root part
• Install the tightening clamp around the neck ensuring the bag is not wrinkled nor doubled underneath of the tightening clamp
• Extra cloth can be folded backwards over the tightening clamp
7. Install the top hat on top of the zipper
• Pull the protective top hat over the zipper • Install the top hat over the sector ensuring the zipper is not outside the hat at any point • If the zipper is too long and outside the hat, cut it shorter so that it fits under the hat • Be careful – do not damage the bag during the installation
Rev.1 / 09.2019
8. Shrink the bags 20 min in hot water 93 – 99 C ( 200 -210 F )
• Put the sectors in the hot water • Water in the shrink tank must be kept at 93°-99°C (200 – 210 F) during the shrinking • Make sure that the whole bag is submerged. Keep sectors in hot water for approx. 20 min
9. Final checking
• After the shrinking, check that sector bags are tight and there are no holes in the cloth • Ensure top hat and tightening clamp are tight and properly installed • Store the sectors clean and out of heat and sunlight
Rev.1 / 09.2019
ANDRITZ SPARE PARTS CONTACTS
ANDRITZ INC. 5405 Windward Parkway, Suite 100W Alpharetta, GA 30004-3894 Matt Nolin p: +1 770 640 2435 email: [email protected] Alison Sims p: +1 770 640 2425 email: [email protected] Marcus Dorsey p: +1 770 640 2478 email: [email protected] Julie Pao p: +1 770 640 2564 email: [email protected] Becky Saenz p: +1 770 640 2452 email: [email protected] Fax number f: +1 770 640 2496