installation instructions fortina louvers > wall > direct...
TRANSCRIPT
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
1
2
3
1. Attaching the Back Rail: Measure and mark the position of your Louvers on the wall.Mark and drill pilot holes in the Back Rail in a diameter smaller than the screw you are using. Attach to wall at pre-marked locations. Attach Endcaps to the Louvers with screws provided before installing the Louvers.
2. Install the Louver by snapping into the Back Rail.
3. Secure the Louver to the Back Rail with a screw through the side.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Louvers > Wall > Direct Attachment > Interior/Exterior
Attachment screws by others
Secure Louver to Back Rail with screws provided
Back Rail
Louver with Endcaps installed
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
1
2
1. SCREW-ON Endcap For direct attachment TLKS Louvers and all THS Louvers
2. SNAP-ON EndcapFor THS Louvers only
On exterior vertical installation, drill two small weep holes on the bottom Endcaps. This will allow for any trapped moisture to drain.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Louvers > Wall > Direct Attachment > Interior/Exterior > Endcaps
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
1. Attaching the Back Rail: Measure and mark the position of your Louvers on the ceiling.Mark and drill pilot holes in the Back Rail in a diameter smaller than the screw you are using. Attach to ceiling at pre-marked locations.
Attach Endcaps to the Louvers with screws provided, as shown on the next page, before installing the Louvers.
2. Install the Louver by snapping into the Back Rail.
3. Secure the Louver to the Back Rail with a screw through the side.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Louvers > Ceiling > Direct Attachment > Interior Only
1
2
3
Attachment screw by others
Secure Louver to Back Rail with screws provided
Back Rail
Louver with Endcaps installed
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Louvers > Ceiling > Direct Attachment > Interior Only > Endcaps
1
2
1. SCREW-ON Endcap For direct attachment TLKS Louvers and all THS-Louvers
2. SNAP-ON EndcapFor THS Louvers only
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
1
2
3
Stringers come pre-notched for spacing specified.
1. Attach BTS Bracket to supporting structure.
2. Secure L-Stringer to BTS Brackets with the bolts provided.
3. Assemble the Louvers onto the Stringers with BTP Clips and tighten to fix them.
Attach Endcaps to the Louvers with screws provided, per instruction on next page.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Louvers > Wall > Stringer Mounted > Interior/Exterior
Support structure by others.
L-Stringer
BTS Bracket with attachment bolts provided
BTP Clip
Louver
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Louvers > Wall > Stringer Mounted > Interior/Exterior
Installation With Back Plate Visible
Back Rails require cutting a notch, as shown above.
Follow instructions mounting Louvers to Stringers.
Cut a 15 mm or larger notch at Back Rail to clear installed BTP clip.
Secure Back Rails to Louvers with screws through back or sides, as shown at left.
Attach Endcaps to the Louvers with screws provided, as shown on the next page.
Notch of 15mm or larger
Stringer
Back Panel
Louver
Back Panel
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Louvers > Wall > Stringer Mounted > Interior/Exterior > Endcaps
1
2
1. SCREW-ON Endcap For direct attachment TLKS Louvers and all THS-Louvers
2. SNAP-ON EndcapFor THS Louvers only
On exterior Vertical installation, drill two small weep holes on the bottom Endcaps. This will allow for any trapped moisture to drain.
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
1
2
3
STCL-1 Stringers are pre-notched per spacing specified. Top channel allows for on-site adjustment of hanging point.
1. Attach the BTS Bracket to your supporting structure. Secure it to the Stringer with bolts provided. The ceiling attachment point can be adjusted by moving bolt along channel before tightening.
2. Attach Endcaps to Louvers. Assemble Louvers to Stringer with BTP Clips provided and tighten to fix.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Louvers > Ceiling > Stringer Mounted > Interior Only
STCL-1 Stringer
Supports to structure by others
BTP Clips
Louver
BTS Bracket and bolt
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Louvers > Ceiling > Stringer Mounted > Interior Only > Endcaps
1
2
1. SCREW-ON Endcap For direct attachment TLKS Louvers and all THS-Louvers
2. SNAP-ON EndcapFor THS Louvers only
On exterior Vertical installation, drill two small weep holes on the bottom Endcaps. This will allow for any trapped moisture to drain.
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
Pro�les Needed
LOUVER COVERTLDU-40
LIGHTING LOUVERTLD-4080
40 33
80
15.5
Installation Cross Section
Lighting Duct Cover TLDU-40
End Cap
Track by others
Track by others
Tracklights by others
Tracklight by others
Lighting Duct LouverTLD-4080
Track light by others Lighting Duct Louver Cover where Track light
does not occur.
Screw-on End Cap is available
IMPORTANT:U-Clipsneeded to attach TLDU-40Lighting Duct Coverto Louver
IMPORTANT:Attaches with U Clips.
Stringers
Tracklight
Stringer
U-Clips
U-Clips
LightingLouverCover
Lighting Louver TLD-4080
1
2
3
Stringers come pre-notched for spacing specified.
1. Install Stringers and Louvers per instructions.
2. Assemble Louvers to Stringer with BTP clips provided and tighten to fix.
3. Locate and attach Track light (by others) into the Louver. Have your Electrician connect to power source.
4.Attach Lighting Duct Cover (TLDU-40) to the Louver using U-Clips provided.
5. Attach Endcaps to Louvers.
6. Connect spot lights to track.Note: Coordinating track is Lytespan by Phillips.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Louvers > Lighting Louvers > Ceiling > Stringer Mounted > Interior Only
Pro�les Needed
LOUVER COVERTLDU-40
LIGHTING LOUVERTLD-4080
40 33
80
15.5
Installation Cross Section
Lighting Duct Cover TLDU-40
End Cap
Track by others
Track by others
Tracklights by others
Tracklight by others
Lighting Duct LouverTLD-4080
Track light by others Lighting Duct Louver Cover where Track light
does not occur.
Screw-on End Cap is available
IMPORTANT:U-Clipsneeded to attach TLDU-40Lighting Duct Coverto Louver
IMPORTANT:Attaches with U Clips.
Stringers
Tracklight
Stringer
U-Clips
U-Clips
LightingLouverCover
Lighting Louver TLD-4080
Pro�les Needed
LOUVER COVERTLDU-40
LIGHTING LOUVERTLD-4080
40 33
80
15.5
Installation Cross Section
Lighting Duct Cover TLDU-40
End Cap
Track by others
Track by others
Tracklights by others
Tracklight by others
Lighting Duct LouverTLD-4080
Track light by others Lighting Duct Louver Cover where Track light
does not occur.
Screw-on End Cap is available
IMPORTANT:U-Clipsneeded to attach TLDU-40Lighting Duct Coverto Louver
IMPORTANT:Attaches with U Clips.
Stringers
Tracklight
Stringer
U-Clips
U-Clips
LightingLouverCover
Lighting Louver TLD-4080
Suspended With Rods
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Louvers > Lighting Louver > Interior Only > Endcaps
1
2
1. SCREW-ON Endcap For direct attachment TLKS Louvers and all THS-Louvers
2. SNAP-ON EndcapFor THS Louvers only
On exterior Vertical installation, drill two small weep holes on the bottom Endcaps. This will allow for any trapped moisture to drain.
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
1
2
3
1. Attach LED rail TLFB-19 to Louver TLF-4080 with screws provided.
2. Peel off protective tape cover of LED-tube and place securely in LED rail.
3. Clip in Louver Cover Units where needed.
4. Mount Louvers to Stringer per their installation instructions.Transformer and installation of lights by a licensed Electrician.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Louvers > Led Light Louver > Stringers > Interior Only
LED Tube
TFLB-19
Louver TLF-4080
TLFU-40 Louver Cover
STCL-1 Stringer
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Louvers > Led Light Louver > Interior Only > Endcap
1
2
1. SCREW-ON Endcap For direct attachment TLKS Louvers and all THS-Louvers
2. SNAP-ON EndcapFor THS Louvers only
On exterior Vertical installation, drill two small weep holes on the bottom Endcaps. This will allow for any trapped moisture to drain.
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
1
2
3
1. Mount L-Brackets to floor and ceiling structure.
2. Take Louver and slide open side into top and bottom brackets and attach with screws provided. (Louver may need to be cut for perfect fit).
3. Attach Back Rail to Louvers and secure with screws provided.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Louvers > Floor To Ceiling > Interior Only
Before Installation of Back Plates
TBF Brackets
Louver
Back Rail
Attachment fasteners by others
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
TP1W30
TP2W40
TP3W50
TBF-8L5/50/75
USE WITH LOUVERS:THS-5010THS-50125THS-5015THS-6012
TBF-4L5/50/75
USE WITH LOUVERS:THS-3075THS-3080THS-3010THS-3015
TBF-7L3/20/50
USE WITH LOUVERS:THS-5050THS-5060
TBF-3L3/30/50
USE WITH LOUVERS:THS-3050THS-3060
TBF-1L3/20/50
USE WITH LOUVERS:THS-2040THS-2060
TBF-5L3/20/50
USE WITH LOUVERS:THS-4040THS-4050
TBF-2L5/50/75
USE WITH LOUVERS:THS-2080THS-2010THS-2015THS-2570THS-2580
TBF-6L5/50/75
USE WITH LOUVER:THS-4080
TP4W60
20 mm
3 mm 12 mm
3 mm
16 mm
Ø 3 mm
Ø 6 mm
50 mm
50 mm
30 mm
5 mm 15 mm
5 mm
20 mm
Ø 3 mm
Ø 6 mm
12 mm3 mm
20 mm
5 mm
30 mm
Ø 6 mm
Ø 3 mm
20 mm
3 mm
5 mm
40 mm
12 mm
20 mm
15 mm
8 mm
10 mm
Ø 6 mm
Ø 3 mm
50 mm
50 mm
75 mm
10 mm
20 mm
50 mm
10 mm 15 mm
Ø 6 mm Ø 6 mm
40 mm
28 mm
16 mm
Ø 5 mm
Ø 5 mm15 m
m10 m
m
8 mm
20 mm
16 mm
Ø 5 mm
Ø 5 mm
10 mm
15 mm
25 mm
8 mm
Ø 5 mm25 m
m
16 mm
30 mm
10 mm
15 mm
8 mm
8 mm
20 mm
15 mm
35 mm
25 mm Ø 5 mm
Ø 5 mm
75 mm
75 mm
15 mm
30 mm
20 mm
40 mm
50 mm
10 mm 15 mm
10 mm 15 mm
50 mm
Ø 6 mmØ 6 mmØ 6 mm Ø 6 mm
16 mm
35 mm
Ø 5 mm
Ø 5 mm
14 mm
28 mm
40 mm
15 mm
35 mm
25 mm
Ø 5 mm
Ø 5 mm
53.5 mm2.5 mm
56 mm
23.9 mm2.5 mm
35 mm2 mm
43.3 mm3 mm
15 mm
10 mm
20 mm
26.4 mm
7.5 mm
7.5 mm
15 mm
10 mm
20 mm
Ø 3.9 mm
Ø 3.9 mm
Ø 3.9 mm
Ø 3.9 mm
45.8 mm
75 mm
8 mm
16 mm
50 mm
10 mm 15 mm
Ø 6 mm Ø 6 mm
8 mm
16 mm
15 mm
35 mm
25 mm Ø 5 mm
Ø 5 mm
16 mm
37 mm
25 mm
15 mm
10 mm
14 mm
Ø 5 mm
25 mm
8 mm
16 mm
30 mm
15 mm
25 mm
2 mm2 mm
7 mm7 mm 6 mm 6 mm
Ø 5 mmØ 5 mm
2 mm 2 mm
6 mm 6 mm7 mm7 mm
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Louvers > Floor To Ceiling > Interior Only > L-Brackets
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Louvers > Floor To Ceiling> Interior Only > L-Brackets
TP1W30
TP2W40
TP3W50
TBF-8L5/50/75
USE WITH LOUVERS:THS-5010THS-50125THS-5015THS-6012
TBF-4L5/50/75
USE WITH LOUVERS:THS-3075THS-3080THS-3010THS-3015
TBF-7L3/20/50
USE WITH LOUVERS:THS-5050THS-5060
TBF-3L3/30/50
USE WITH LOUVERS:THS-3050THS-3060
TBF-1L3/20/50
USE WITH LOUVERS:THS-2040THS-2060
TBF-5L3/20/50
USE WITH LOUVERS:THS-4040THS-4050
TBF-2L5/50/75
USE WITH LOUVERS:THS-2080THS-2010THS-2015THS-2570THS-2580
TBF-6L5/50/75
USE WITH LOUVER:THS-4080
TP4W60
20 mm
3 mm 12 mm
3 mm
16 mm
Ø 3 mm
Ø 6 mm
50 mm
50 mm
30 mm
5 mm 15 mm
5 mm
20 mm
Ø 3 mm
Ø 6 mm
12 mm3 mm
20 mm
5 mm
30 mm
Ø 6 mm
Ø 3 mm
20 mm
3 mm
5 mm
40 mm
12 mm
20 mm
15 mm
8 mm
10 mm
Ø 6 mm
Ø 3 mm
50 mm
50 mm
75 mm
10 mm
20 mm
50 mm
10 mm 15 mm
Ø 6 mm Ø 6 mm
40 mm
28 mm
16 mm
Ø 5 mm
Ø 5 mm
15 mm
10 mm
8 mm
20 mm
16 mm
Ø 5 mm
Ø 5 mm
10 mm
15 mm
25 mm
8 mm
Ø 5 mm
25 mm
16 mm
30 mm
10 mm
15 mm
8 mm
8 mm
20 mm
15 mm
35 mm
25 mm Ø 5 mm
Ø 5 mm
75 mm
75 mm
15 mm
30 mm
20 mm
40 mm
50 mm
10 mm 15 mm
10 mm 15 mm
50 mm
Ø 6 mmØ 6 mmØ 6 mm Ø 6 mm
16 mm
35 mm
Ø 5 mm
Ø 5 mm
14 mm
28 mm
40 mm
15 mm
35 mm
25 mm
Ø 5 mm
Ø 5 mm
53.5 mm2.5 mm
56 mm
23.9 mm2.5 mm
35 mm2 mm
43.3 mm3 mm
15 mm
10 mm
20 mm
26.4 mm
7.5 mm
7.5 mm
15 mm
10 mm
20 mm
Ø 3.9 mm
Ø 3.9 mm
Ø 3.9 mm
Ø 3.9 mm
45.8 mm
75 mm
8 mm
16 mm
50 mm
10 mm 15 mm
Ø 6 mm Ø 6 mm
8 mm
16 mm
15 mm
35 mm
25 mm Ø 5 mm
Ø 5 mm
16 mm
37 mm
25 mm
15 mm
10 mm
14 mm
Ø 5 mm
25 mm
8 mm
16 mm
30 mm
15 mm
25 mm
2 mm2 mm
7 mm7 mm 6 mm 6 mm
Ø 5 mmØ 5 mm
2 mm 2 mm
6 mm 6 mm7 mm7 mm
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
1
2
3
1. Install trim piece (if used) to one side of layout.
2. Starting from the other side, attach (tongue and groove) Slats to surface.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Slats > Ceiling > Interior/Exterior
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Slats > Ceiling > Interior/Exterior
LONGITUDINAL SECTION USING M-16 LONGITUDINAL SECTION USING M-19-1
150
M-16
M-16
SLAT15
900
SLAT
SLAT
SLAT
SLATM-19-1
M64
30
CROSS SECTION USING M-16
JOINT DETAIL USING M-64
CROSS SECTION USING M-19-1
M-19-1
15 15
5
5
15
3819
13
13
SLAT
M-71SLAT
SLAT
DROP CEILING DETAIL USING M-71・78
M-78153153
5
25
27
5
1319
38
131938 1319
38
(25)20
338
19
M-16 t=1.2
M-64 t=1.2
M-19-1 t=1.2 M-70 t=1.2
M-6 t=1.5 M-68 t=1.2
M-71 t=1.3
M-78 t=1.2
40
19
18
15
6014
579
27
25
14 5
4.7
145
1530 45
15 15
10
145
20
40
143
50.233.2
50.2
33.2
143
15
143
15
14 3
143 25
50
2550
M-67 t=1.2
M68
25
5 10
19
M-69 t=1.5
R75
155
1510
0
100
M68
Trims /Edge Treatment
H Joints
Corner Trims
Exterior Corner Trim Interior Corner Trim
13mm
13mm/23mm
Slat > Installation Examples
Slat > Acessories
INSIDE AND OUTSIDE CORNER USING M-70・78
25
25
3
3
M-78 M-70SLATS
133010
1330
10
133010
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
1. Attach trim piece at top of installation location on wall.
2. Insert Slat into trim piece and attach Slat to wall with screws.
3. Continue mounting the tongue and groove Slats by inserting into the Slat above, so it lodges in place. Install bottom trim piece to wall with screws at correct location to allow the last Slat to be inserted.
4. Install the last slat by sliding it in, up, and down so it rests in bottom trim piece. No need to screws on the bottom Slat.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Slats > Wall > Interior/Exterior
1
2
3
4
Fortina For B+N
B+N Industries
1409 Chapin Avenue, Burlingame, California 94010
Tel: (800) 350-4127
Web: Fortina.bnind.com
Email: [email protected]© B
+N
Indu
strie
s, In
c.
I N S T A L L A T I O N I N S T R U C T I O N S
Fortina Slats > Wall > Interior/Exterior
LONGITUDINAL SECTION USING M-16 LONGITUDINAL SECTION USING M-19-1
150
M-16
M-16
SLAT15
900
SLAT
SLAT
SLAT
SLATM-19-1
M64
30
CROSS SECTION USING M-16
JOINT DETAIL USING M-64
CROSS SECTION USING M-19-1
M-19-1
15 15
5
5
15
3819
13
13
SLAT
M-71SLAT
SLAT
DROP CEILING DETAIL USING M-71・78
M-78153153
5
25
27
5
1319
38
131938 1319
38
(25)20
338
19
M-16 t=1.2
M-64 t=1.2
M-19-1 t=1.2 M-70 t=1.2
M-6 t=1.5 M-68 t=1.2
M-71 t=1.3
M-78 t=1.2
40
19
18
15
6014
579
27
25
14 5
4.7
145
1530 45
15 15
10
145
20
40
143
50.233.2
50.2
33.2
143
15
143
15
14 3
143 25
50
2550
M-67 t=1.2
M68
25
5 10
19
M-69 t=1.5
R75
155
1510
0
100
M68
Trims /Edge Treatment
H Joints
Corner Trims
Exterior Corner Trim Interior Corner Trim
13mm
13mm/23mm
Slat > Installation Examples
Slat > Acessories
INSIDE AND OUTSIDE CORNER USING M-70・78
25
25
3
3
M-78 M-70SLATS
133010
1330
10
133010