installation instructions for trilock omni...
TRANSCRIPT
Step 3.• Mark and chisel latch faceplate to a recess of 3mm.
Use latch carrier as a template.• Insert lock body into 60mm (2 3/8") slot.• Insert latch carrier through 22mm
(7/8") hole into lock body assembly and tighten with 2 screws.
Ensure T-shaped hole at rear of latch carrier is upright!
Step 4a.Trilock latch bolt re-handing.• Check that tapered side of the
latch bolt faces towards the door jamb.• It may be necessary to unclip
the rear arm & rotate bolt 180̊.• This is achieved by following steps:
Step 4.• Insert the latch through the slot in the carrier until it can go no further.• Insert the key and turn to retract the latch bolt.• Pre-drill wood screw holes with suitable drill size.• Install plastic faceplate shim and faceplate, then screw into position.
Step 2.• Mark vertical lines between
two holes as per illustration.• Cut along marked lines.
Mark vertical lines between holes as shown. Cut along vertical lines.
NOTE: • carefully follow these instructions when installing. • do not overtighten screws. • use of power driver is not recommended. • fully remove the Trilock prior to painting the door to avoid harming the product's finish.
PAIT 147JAN ‘15
Patent Pending
B
T-Shaped hole
Rear viewof latch
Latchcarrier
1. Remove latch bolt assembly from carrier
4. Rotate bolt 180˚ 5. Re-attach arm to latch bolt 6. Rotate arm upwards & fit back into carrier
2. Rotate arm downwards 3. Unclip arm from latch bolt
Lock body
Arm
Rotate Bolt 180˚
Installation Instructions for Trilock Omni BBTwin Pull Handle Version - Suits 35mm to 45mm door thickness
Step 1.• Fold template where indicated.• Position template on door edge at
desired lock / latch height.• Firmly hold template and mark latch
height and 2 60mm holes centres.• Measure door thickness and mark
centre on 'latch height' marking.• Drill 22mm (7/8") latch hole. Note: it is important to drill this
hole squarely.• Drill pilot holes [suggested size
3mm (1/8")]. Then enlarge holes to 60mm, drilling from both sides of the door. In particular, ensure the 60mm dia. holes through door face are drilled only to this size, otherwise correct functioning may be impeded – refer template.
Please note: Ensure the template position and orientation is as shown, incorrect installation voids warranty.
template
Step 7.• Install 2 posts to Trilock external faceplate
(this is the faceplate without the rectangular snib push-button).
Step 8.• Mount the inside faceplate so that
mark on large gear engages with mark on lock bodygear.
NOTE: • carefully follow these instructions when installing. • do not overtighten screws. • use of power driver is not recommended. • fully remove the Trilock prior to painting the door to avoid harming the product's finish.
Step 6.To re-hand external lever & set lever operation (if required).• If re-handing is required remove the stop
screw from SS1 & fit to SS2, to allow lever to operate away from door edge.
NOTE: There is no need to re-hand the internal lever.
NOTE: These steps are applicable to leverset only.
Step 9.• Insert spring and snib rotor in the square hole
of the internal lever.• Position snib rotor so one notch faces up and
the other notch points to the latch side.• Mount outside furniture plate to outside of the
door, and align the two making sure the snib rotor engages with the external lever.
• Fit mounting screws (2 of) from inside and tighten into threaded posts.
• Fit wood screws (3 of) to inside furniture plate (recommend pilot drilling before fitting screws).
NOTE: Test all functions for smooth operation.
SS2
SS1
Note: Position snib rotor so one notch facesup & the other notch points to the latch side.
Note: Assemble spring with plastic insert to snib rotor as shown.
Mounting screws (2 of)
Snib RotorSpring
Plastic Insert
Wood screws (3 of)
Installation Instructions for Trilock Omni BBTwin Pull Handle Version - Suits 35mm to 45mm door thickness
Step 5.• Remove perforated cut-out from
cardboard template and place over lock body, making sure template is square to door edge.
• While holding template firmly in position, mark remaining 4 holes, as indicated on both sides of the door (reversing template as required).
• Drill pilot holes from both sides of the door [suggested size 3mm (1/8")] then enlarge, again from both sides of the door, to sizes indicated on template, otherwise correct functioning may be impeded – refer template.
12
34
PAIT 147JAN ‘15
NOTE: • carefully follow these instructions when installing. • do not overtighten screws. • use of power driver is not recommended. • fully remove the Trilock prior to painting the door to avoid harming the product's finish.
Step 12.Fixing of double pull handleNote: Suitable for solid doors only.• Check and make sure that the inside & outside faceplates are lined up straight
and square with the door. • Once the desired position of the inside & outside faceplate has been confirmed,
mark the centre of the hole at the top of the faceplate and proceed to drill a suitable hole. Note: When drilling the hole drill hole from both sides of the door with a 9mm drill bit.
• Hold the unthreaded bush onto the inside faceplate, ensuring the chamfered hole of the bush, is facing away from the door.
• Then, from the same side, install the suitable M8 screw through the bush and through the door.
• Then, from the outside faceplate fit the threaded bush ensuring chamfered hole of the bush, is facing away from the door.
• Tighten M8 screw securely with suitable screwdriver.• Place the pull handle over top of 2 mounting bushes. • Line up the pull handle so that it is lined up straight and square. Insert the grub
screws and tighten with allen key provided.• Repeat for 2nd pull handle.
Step 10.• For single cylinder applications install internal
turnbutton now by tightening grub-screw onto protruding shaft.
allen key
grub-screw
Installation Instructions for Trilock Omni BBTwin Pull Handle Version - Suits 35mm to 45mm door thickness
M8 x 82mm bolt un-threadedbush
timberdoor
grub screwgrub screw
singlepull handle
threadedbush
pull handlesupport
outside faceplateinside faceplate
Note: Ensure the chamfered holeof the bush, is facing away from the door.
singlepull handle
doorframe
• Mark and drill a 25mm (1") hole to a depth of 25mm (1"), at a corresponding height to the bolt.
• Mark and chisel recesses for strike plate.• Screw into position using 2 wood screws as supplied.Door Adjustment Check1 When door is closed using finger pressure, ensure
bolt is latching into strike plate.2 If door is rattling when in latched position. Open door,
remove strike plate & adjust anti-rattle tab & refit strike plate to door frame. Repeat check 1.
Step 11.All door seals must be fitted prior to fitting strike plate.• Position the door so that the centrepoint of the
strike plate can be marked on door frame.
anti-rattle tab
PAIT 147JAN ‘15
PAIT 147JAN ‘15
Patent Pending
Designed in Australia by Gainsborough Hardware Industries Limited, Melbourne, Australia. A.B.N. 25 004 792 269
www.gainsboroughhardware.com.au
Exploded Diagram
snib rotor
spring
plasticinsert
strike plate
ORI
GIN
ATIO
N C
RM G
SH 9
54 0
115
faceplatelatch
latchcarrier
2 x mounting screws
plasticfaceplateshim
insidefurniture
3 x wood screws
cylinderlock body
outsidefurniture
Installation Instructions for Trilock Omni BBTwin Pull Handle Version - Suits 35mm to 45mm door thickness
Step 1.• Fold template where indicated.• Position template on door edge at
desired height align with operating Omni on opposite door.
• Firmly hold template and mark 4 10mm holes centres & 1 19mm hole centre.
Note: it is important to drill these holes squarely.
• Drill pilot holes [suggested size 3mm (1/8")].
• Then enlarge holes as per template, drilling from both sides of the door.
Step 2.• Install 2 of M4 threaded posts to
Omni external faceplate.
Please note: Ensure the template position and orientation is as shown, incorrect installation voids warranty.
NOTE: • carefully follow these instructions when installing. • do not overtighten screws. • use of power driver is not recommended. • fully remove the Trilock prior to painting the door to avoid harming the product's finish.
MSC1DOC02UM1AUG ‘14
Patent Pending
Installation Instructions for Trilock Omni BB DummyTwin Pull Handle Version – Suits 35mm to 45mm door thickness
Step 3.• Fit 2 of mounting screws from inside and
tighten into threaded posts.• Fit 3 of wood screws to inside furniture
plate.• Install pull handle as per instructions
below.
Step 4.Fixing of double pull handleNote: Suitable for solid doors only.• Check and make sure that the inside & outside faceplates are lined up straight and
square with the door. • Once the desired position of the inside & outside faceplate has been confirmed, mark
the centre of the hole at the top of the faceplate and proceed to drill a suitable hole. Note: When drilling the hole drill hole from both sides of the door with a 9mm drill bit.
• Hold the unthreaded bush onto the inside faceplate, ensuring the chamfered hole of the bush, is facing away from the door.
• Then, from the same side, install the suitable M8 screw through the bush and through the door.
• Then, from the outside faceplate fit the threaded bush ensuring the chamfered hole of the bush, is facing away from the door.
• Tighten M8 screw securely with suitable screwdriver.• Place the pull handle over top of 2 mounting bushes. • Line up the pull handle so that it is lined up straight and square.
Insert the grub screws and tighten with allen key provided.• Repeat for 2nd pull handle.
M8 x 82mm bolt un-threadedbush
timberdoor
grub screwgrub screw
singlepull handle
threadedbush
pull handlesupport
outside faceplateinside faceplate
Note: Ensure the chamfered holeof the bush, is facing away from the door.
singlepull handle
MSC1DOC02UM1AUG ‘14
Patent Pending
Installation Instructions for Trilock Omni BB DummyTwin Pull Handle Version – Suits 35mm to 45mm door thickness
Designed in Australia by Gainsborough Hardware Industries Limited, Melbourne, Australia. A.B.N. 25 004 792 269
www.gainsboroughhardware.com.au
Exploded Diagram
insidefurniture
outsidefurniture
pullhandle
threaded bush
bolt
post
mounting screws
ORI
GIN
ATIO
N C
RM G
SH 9
54 0
814
10mm (3/8") hole
10mm (3/8") hole
FO
LD
HE
RE
PAIT 158
SEP ‘12
Patent Pending
Inst
alla
tion
te
mp
late
fo
r G
ain
sbo
rou
gh
Trilo
ck O
mn
i Du
mm
y S
ing
le P
ull
Ha
nd
leS
uits
35m
m to
45m
m d
oor
thic
knes
ses
Fit here on door edge
Fit here on door edge
Fit here on door edge
BACKSET 60mm (2 3/8")
19mm (3/4") hole
54mm (2 1/8") hole
PAIT 158
SEP ‘12
Patent Pending
Inst
alla
tion
te
mp
late
fo
r G
ain
sbo
rou
gh
Trilo
ck O
mn
i Du
mm
y S
ing
le P
ull
Ha
nd
leS
uits
35m
m to
45m
m d
oor
thic
knes
ses
Fit here on door edge
OR
IGIN
AT
ION
CR
M G
SH
853 0
912
10mm (3/8") hole
10mm (3/8") hole
Fit here on door edge
Fit here on door edge
BACKSET 60mm (2 3/8")
19mm (3/4") hole
54mm (2 1/8") hole
PAIT 161OCT ‘14
Patent Pending
Inst
alla
tion
tem
plat
e fo
r Gai
nsbo
roug
h Tr
ilock
Om
ni B
ack
to B
ack
Pull
Han
dle
Suits
35m
m to
45m
m d
oor t
hick
ness
es
LATCH HEIGHT
22mm (7/8")
Fit here on door edge
60mm(2 3/8") hole
60mm(2 3/8") hole
3mm (1/8")
Important NoteMake sure you follow the step by step instructions carefully
BACKSET 60mm (2 3/8")
Fit here on door edge
Fit here on door edge
FOLD
HER
E
10mm (3/8") hole
10mm (3/8") hole
PAIT 161OCT ‘14Patent Pending
Inst
alla
tion
tem
plat
e fo
r Gai
nsbo
roug
h Tr
ilock
Om
ni B
ack
to B
ack
Pull
Han
dle
Suits
35m
m to
45m
m d
oor t
hick
ness
es
LATCH HEIGHT
22mm (7/8")
Fit here on door edge
3mm (1/8")
Important NoteMake sure you follow the step by step instructions carefully
BACKSET 60mm (2 3/8")
Fit here on door edge
Fit here on door edge
FOLD
HER
E
60mm(2 3/8") hole
60mm(2 3/8") hole
10mm (3/8") hole
10mm (3/8") hole
OR
IGIN
ATIO
N C
RM
GS
H 9
54 0
814