innovative refinements to the tactical … refinements to the tactical carbine ... dis con nec tor...
TRANSCRIPT
www.USAmade-AR15parts.comINNOVATIVE REFINEMENTS TO THE TACTICAL CARBINE
USER MANUALAR15 STYLE RIFLES
7075 Forged Mil-spec CNC machined-hard anodized lower receiver with accurizing screw and detent set screw.
Barnes Precision Machine © Copyright 2013Patent Pending, All Rights Reserved
Picatinny Spec Free-Float Rail System. Available in 7, 9, 12.5, and 14.5 inch lengths, featuring our patent pending enhanced barrel nut to achieve unprecedented rigidity for the length of the rail. Each rail system features four steel reinforced interchangeable sling swivel inserts.
All Barnes Precision Machine rifles come standard with a stainless steel match grade barrel. Available in your choice of .223 Wylde or 5.56 NATO chambers and 11.5 to 18 inch lengths.
Barnes Precision Machine A2-Style muzzle device. Reduces muzzle blast and felt recoil, complete with breaching tip.
MADE IN THE USA
OPERATING INSTRUCTIONSFor safe operation instructions including Proper /Safe usage and /or maintenance, cleaning, repair, BPM Inc. recommends completion of a class by certified instructor (NRA/NSSF, etc.) for training /operational understanding-proper, safe use of weapon system for tactical/personal defense/target/hunting as well as all other applications requiring basic understanding of said product(s) for SAFE /RELIABLE use/application of a LETHAL WEAPON.
WARRANTYDue to the many different requirements imposed by federal and state laws on consumer warranties, no express warranty, either “full” or “limited” is offered with this product.
BPM Inc. Implied warranties, including the implied warranty of merchantability and fitness for a particular purpose, are limited in duration to one year from the date of purchase. BPM Inc. will not cover normal wear and tear or abuse. Some states do not allow limitations on how long implied warranty lasts, so this limitation may not apply to you. Decision on Parts replacement is up to BPM Inc. - after return of part / inspection of part/assembly. BPM Inc. reserves the right to disallow replacement of parts, based on neglect/abuse of said products by end user, pending review /inspection at our plant/facility. All parts/items/assemblies found after inspection to be defective /improperly manufactured will be replaced/returned at no cost to customer.
WARNING: Observe safe firearm handling practices at all times! Make sure the weapon is unloaded and the safety engaged!
IMPROPER INSTALLATION AND/OR IMPROPER USE OF THIS PRODUCT MAY CAUSE WEAPON MALFUNCTION. WEAPON MALFUNCTION MAY CAUSE SERIOUS INJURY, INCLUDING DEATH AND/OR BODILY HARM
Neither Barnes Precision Machine, Inc. nor its affiliates will be held responsible for improper use or improper installation of this product. Proper installation and use modifies the weapon and its operational procedures. Verify proper installation and practice use extensively before entering a tactical or other live fire situation. Failure to do so is legal recklessness on the part of the user.
REMEMBER: NEVER POINT THE BARREL OF YOUR WEAPON AT ANYTHING YOU DO NOT WANT TO DESTROY.
Congratulations, you have purchased one of the finest rifles in the industry.
Mil-spec machine tolerances. Manufactured on state of the art CNC machinery. Top quality materials-coating. All performed to ISO9001 standard. USA made craftsmanship and pride by skilled machinists in our North Carolina Facility. Innovative refinements to the tactical carbine
PICATINNY SPECQUAD RAIL
ENHANCEDBARREL NUT
STEEL REINFORCEDINTERCHANGEABLE
SLING SWIVEL INSERT
To install or remove correctly, user must be familiar with common Armorers tools used in assembly/disassembly of M-16/AR-15 weapon system and have the skills necessary to use them. Use of “Service removable Blue LocTite” on all fasteners is recommended.
UNLOAD WEAPON It is users responsibility to make sure weapon is unloaded and in safe condition!!! BPM INC will not be responsible for any loss, injury or death resulting
from the use or misuse of this product.
The patent pending design of the considerably longer length barrel nut over what has been conventionally available ,coupled with hand guard to barrel nut retention via QD sling swivel insert is remarkably one of the toughest/most rigid in existence. Length of barrel nut offers unequalled rigidity under leverage induced sling wrap up –strain-especially for longer /full length rail type hand guard designs, for effective/repeatable mounting of a variety of different optics/lasers/light accessories.
Barnes Precision Picatinny Spec Free Float Rail
1. Use vise /upper receiver Armorers block –barrel nut wrench to remove GI style barrel nut/delta ring assembly.
2. Install Barnes Precision Machine Inc. Barrel Nut with radial groove.
6. Install QD sling swivel disconnect inserts into threaded holes on each side of barrel nut area on hand guard. Torque QD sling swivel inserts on each side to 35 inch pounds.
7. Torque clamp screws to 25 inch pounds.
CAUTION: Do not distort/over tighten screws! Slot in clamp area on underside of hand guard should not “close up”.
8. Re-Check alignment of Picatinny spec rail on hand guard with Picatinny spec rail on upper receiver.
9. Congratulations, you have successfully completed installation of hand guard!
5. While upper is still in Armorers block, Install jack screw (10-32 cap head screw) in bottom of hand guard to open up clamp area to make it easier to slide hand guard onto barrel nut. With 2 rear sling swivel inserts removed from BPM Inc. Free Float Rail, slide rail system on to barrel nut ,maintaining alignment of lug/ recess area on bottom and on top of rail –this lug/ recess area on upper receiver end of hand guard, should fit around upper receiver. Picatinny spec rail on upper receiver and hand guard should align with each other as they come together .This lug/recess area is what keeps hand guard from rotating or loosening barrel nut once in place and tightened up against upper receiver. Once in place remove 10-32 jack screw. Install 10-32 allen head cross bolts and allen nuts thru holes over clamp/slot area on bottom of hand guard– tighten both screws finger tight.
3. Torque barrel nut with BPM Inc. barrel nut wrench to 85ft. lbs.
4. Reinstall gas tube assembly/gas block.
HAND GUARDSNAP RING
WELD SPRING
DELTA RING
BARREL INDEXING PIN
BARREL EXTENSION
BARREL NUT
THERMOSET HANDGUARD
THERMOSET HANDGUARD
FRONT SIGHT POST
FRONT SIGHT DETENT SPRING
FRONT SIGHT DETENT
FRONT SLING SWIVEL
FRONT SLING SWIVEL RIVET
BARREL SUBASSEMBLY
CRUSH WASHER
FLASH SUPPRESSOR
HANDGUARD CAP
GAS TUBE ROLL PIN
FRONT SIGHT BASE WITH BAYONET LUG
CARBINE GAS TUBE
FRONT SIGHTTAPER PINS (2)
BOLT CARRIER KEY SCREW (2)
BOLT CARRIER KEY
FIRING PIN RETAINING PIN
CAM PIN
FIRING PIN
BOLT CARRIER
BOLT GAS RINGS (3)BOLT
EXTRACTOR SPRINGEXTRACTOR SPRING INSERT
EXTRACTOR
EXTRACTOR PIN
EJECTOR ROLL PIN
EJECTORSPRING
EJECTOR
F I R E
S A F E
BOLT CATCH
BOLT CATCH ROLL PIN
BOLT CATCH PLUNGER
MAGAZINECATCH
BOLT CATCH SPRING
BUFFER RETAINER
BUFFER RETAINER
TAKEDOWN PIN SPRING
TAKEDOWN PIN
TAKEDOWN PIN DETENT
SAFETY DETENT SPRING
LOCK WASHER
PISTOL GRIP SCREW
PISTOL GRIP
SAFETY DETENT
HAMMER ANDTRIGGER PINS
MAGAZINERELEASEBUTTON
TRIGGER GUARD PIVOT ROLL PIN
TRIGGERGUARDASSEMBLY
DISCONNECTOR SPRING
DISCONNECTOR
TRIGGER SPRING
PIVOT PIN
PIVOT PINSPRING
PIVOT PINDETENT
MAGAZINECATCHSPRING
BUFFER ASSEMBLY
CAR. BUFFER SPRING
PIN, BUTTSTOCKSLIDE LOCK
LOCKPIN SPRING
TELESTOCKLATCH
6 POSITION CARBINE RECEIVER EXTENSION
RECEIVEREXTENSION
NUT
COLLAR,BUTTSTOCK TUBE LOCK
LOCKPIN NUTROLL PIN
HAMMER WITH J PIN
TRIGGER
HAMMER SPRING
SAFETY SELECTOR LEVER
CHARGINGHANDLE
LATCHROLL PIN
CHARGING HANDLELATCH SPRING
CHARGING HANDLELATCH
CHARGING HANDLE
FORWARD ASSISTSPRING PIN
EJECTION PORT COVER SPRING
EJECTION PORT COVER
EJECTION PORTCOVER PIN
RING,RETAINING COVER
UPPERRECEIVER
FORWARD ASSISTSPRING
PAWL DETENT
FORWARD ASSISTPAWL
PAWL SPRING
PAWL SPRING PIN
FORWARD ASSISTPLUNGER
BARNES PRECISION AR15 PARTS DIAGRAM
WARNING: Observe safe firearm handling practices at all times! Make sure the weapon is unloaded and the safety engaged!
IMPROPER INSTALLATION AND/OR IMPROPER USE OF THIS PRODUCT MAY CAUSE WEAPON MALFUNCTION. WEAPON MALFUNCTION MAY CAUSE SERIOUS INJURY, INCLUDING DEATH AND/OR BODILY HARM
Neither Barnes Precision Machine, Inc. nor its affiliates will be held responsible for improper use or improper installation of this product. Proper installation and use modifies the weapon and its operational procedures. Verify proper installation and practice use extensively before entering a tactical or other live fire situation. Failure to do so is legal recklessness on the part of the user.
REMEMBER: NEVER POINT THE BARREL OF YOUR WEAPON AT ANYTHING YOU DO NOT WANT TO DESTROY.
www.BarnesPrecision.com
INNOVATIVE REFINEMENTS TO THE TACTICAL CARBINE
1434 FARRINGTON ROAD, APEX, NC [email protected]
919-362-6805
DESIGNATED MARKSMAN RIFLE
CQB PATROLMAN’S CARBINE
TACTICAL MATCH CARBINE
BPMUM223