Mipa Ziehspachtel PL10 Product Information

gb 2/0910

page 1 / 2

Product description

Description : Mipa Ziehspachtel PL10 is an elastic two-component long-term paste filler based on unsaturated polyester resins. To be used for iron, steel, aluminium and glass fibre reinforced materials. Due to its fine grain the putty is also suitable for application in very thin coats. Its long pot life allows spot-repair on very large areas. Temperature stability by short time exposure up to 180 °C.

Operational Sector : Mipa Ziehspachtel PL10 is particularly qualified for therepairment of larger body areas especially in commercial vehicle sector and to level out the unevenness on machine parts. Due to its resin formulation, this type of putty is also suitable for powder coating. Resistant to the high stoving temperatures. To be applied from thick to extreme thin (towards zero) coats.

Binder base : Unsaturated polyester resins

Colour : Grey

Storage : At least 1 year, if the original tins are kept closed.

VOC Legislation: EU limiting value for the product (cat. B/b): 250 g/l (2007) This product contains max. 15 g/l VOC [0.125 lbs/gal]

Application

Substrate Treatment : Clean, derust, degrease and sand roughly the surface. Old coats have to be totally removed only in case of thermoplastic coats, nitro-cellulose based paint as well as acid reacting coats; otherwise it will be enough to sand roughly the substrate to ensure that the key is adequate. Degrease and sand roughly theepoxy substrates. Same procedure for glass fibre reinforced plastics. After that mix well Mipa Ziehspachtel PL10 with hardener and apply in the desired coat thickness. Subsequently insulate with a groundcoat Mipa 1K or 2K-Grundierung.

Mixing ratio : Mix well Mipa Ziehspachtel PL10 with approx. 2 - 3% Härter P (by weight). An excess use (more than 3%) of hardener can result in a stained surface.

This data sheet is for information purpose only! To our knowledge the data provided complies with the latest standard and is based on years of experience in the manufacture of our products. However the data is not binding and without warranty. Please follow recommendations stated on the relevant safety data sheet and precautions stated on the product label. We reserve our

right to make additions, deletions, or modifications to the information at any time without prior notification.

MIPA AG · D-84051 Essenbach · Tel. 08703/922-0 · Telefax 08703/922-100

Mipa Ziehspachtel PL10

Product Information

gb 2/0910

page 2 / 2

Pot life : At 20 °C and an amount of 2 % hardener Mipa Härter P, the

paste remains workable for up to 10 - 15 minutes. Drying : At 20 °C full cure after about 60 minutes. The proc ess can be

accelerated by force drying at 50 - 60°C or by usin g IR-lamps. Attention: the polyester putty will not harden at under + 15 °C.

Sanding : Sand dry after approx. 1 hour.

Rough sanding with P80 - P120 grade paper Final sanding with P240 - P280 grade paper before the application of the groud coat.

Safety instructions

Keep away from children. Keep containers in well ventilated rooms. Keep away from food, drink and animal feeding stuffs. Do not breathe aerosol. Avoid contact with eyes. If swallowed, seek medical advice immediately and show this container or label.

Cleaning of tools

Tools should be cleaned immediately after use with an universal diluent Mipa Universalverdünnung. When set hard the putty cannot be removed.

This data sheet is for information purpose only. To our knowledge the data provided complies with the latest standard and is based on years of experience in the manufacture of our products.However the data is not binding and without warranty.

MIPA AG · D-84051 Essenbach · Tel. 08703/922-0 · Telefax 08703/922-100