infinity - kell
TRANSCRIPT
PRODUCT MANU-Revision 2.2Nov. 2014
INFI
NIT
YINTERNAL PARTITIONSYSTEM
PRODUCT MANUAL(Draft)REV. 0Feb. 2015
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
ii
Index ................................................................................................................................................................. ii
Legal Disclaimer ...............................................................................................................................................1
Overview...........................................................................................................................................................2
Profile Identification ............................................................................................................................................
Curtain Wall System Profiles ........................................................................................................................................... 3-4
Hardware Components.......................................................................................................................................
Recommended CW Hardware components ....................................................................................................................... 5
Machining ...........................................................................................................................................................
Infin Comp Channel............................................................................................................................................................ 6
Infin Sill ............................................................................................................................................................................... 7
Infin Sill Cover .................................................................................................................................................................... 8
Infin Frame .................................................................................................................................................................... 9-10
Infin Single Bead ...............................................................................................................................................................11
Infin Double Bead ............................................................................................................................................................. 12
Infin Clips.......................................................................................................................................................................... 13
Glass Cutting Formula................................................................................................................................................. 14-15
Gasket & Glass Chart....................................................................................................................................................... 16
Bead Cutting Formula ................................................................................................................................................. 17-18
Vertical Clip-on profiles cutting sizes ................................................................................................................................ 19
Assembly ............................................................................................................................................................
Sill Cover .......................................................................................................................................................................... 20
Typical Sections..................................................................................................................................................
Door Jamb Details ....................................................................................................................................................... 21-22
Door Head Detail .............................................................................................................................................................. 23
Vertical Detail ................................................................................................................................................................... 24
Corner Detail .................................................................................................................................................................... 25
Radius Corner Detail ........................................................................................................................................................ 26
INTE
RN
AL
PAR
TITI
ON
SYS
TEM
INFI
NIT
YINDEX
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
1
By continuing to use this documentation you acknowledge that you understand and accept the legal disclaimer.
General Documentation DisclaimerThis manual is intended as a manufacturing and installation advisory document. For correct specifications, sizing of profiles and structural information please consult the Starfront Application. If the information you require is not available through the Starfornt Application, please contact your stockist before proceeding. It is advisable to have all sizing and performance criteria checked by a qualified structural engineer to ensure that all perfomance and compliance will be met.
All information, recommendations or advice contained in this documentation is given in good faith to the best of Wispeco’s knowledge and is based on current procedures in effect.
Since the actual use of this documentation by the user is beyond the control of Wispeco, such use is within the exclusive responsibility of the user. Wispeco cannot be held responsible for any loss incurred through incorrect or faulty use of this documentation. Training of Wispeco systems is important for ensuring correct procuderes in the manufacturing of products.
Great care has been taken to ensure that the information provided is correct.
Ensure that you have the latest available manual. The revision number and date can be checked on the latest Starfront version.
Wispeco will accept no responsibility for any errors and/or omissions, which may have inadvertently occurred.
This Guide may be reproduced in whole or in part in any form or by any means provided the reproduction or transmission acknowledges the origin, revision number and copyright date.
Specifications concerning products and applications
This manual is based on standard configurations only. As there are many configurations not covered in this manual, contact your stockist with regard to a configuration not represented herein.
AutoDesk drawings (CAD Symbol Library) are available on request and can be issued with the consent of the Wispeco Technical Department.
All mechanical joints must be sealed with a Wispeco approved joint sealer. Failure to correctly seal the joints can affect the performance of the system. Information on joint sealing can be found in the Cleaning & Mainanace Manual available for download from the Wispeco website.
All drawings in the Wispeco Documentation are shown NOT to scale and are used for illustative purposes only. For correct sizing and machining of system profiles refer to the Wispeco Starfront Application.
Wispeco cannot accept responsibility for the use of standard products since Wispeco does not know where these products are being installed.
The hardware recommended in this documentation is suitable for use in most atmospheric environments. When hardware is used in severe coastal environments the manufacturer of the hardware must be consulted.
The use of non-specified hardware or incorrect mechanisal fasteners can adversly affect the mechanical and weathering performance of the system and we strongly advise against deviations. A Wispeco Consultant can advise you of any hardware issues and limitations with regard to this system.
The use of anti-magnetic stainless steel screws and aluminium pop rivets is recommended to reduce galvanic corrosion in harsh environments.
Fixing lugs on frames must be positioned as per the user manual and used in accordance to the AAAMSA specifications. When profiles are screwed together the screw centers must also be according to the user manual or as specified by an engineer.
All glass used within Wispeco products must comply with SAGGA regulations. Laminated glass must not stand in water.
LEGAL DISCAIMER
INTE
RN
AL
PAR
TITI
ON
SYS
TEM
INFI
NIT
Y
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
2
OVERVIEW
The Crealco Infinity glass partition system has been uniquely designed for easy manufacturing & installation of office glass partitions. The partition system is able to be installed with iether single or double glass panels with the option of fitting venetian blinds for privacy. The system is also able to accommodate 16 mm wood panels.
The Crealco Infinity glass partition system has been designed for internal applications only & may not be used for external purposes as the system has not been tested for water penetration.
The Infinity system has a specially designed sill which is able to house both networking & electrical cabling seperatly & accommodate an electrical plug & cover.
Clip 44 aluminium doors can be incorporated into the system along side the glass partitions. There are also options for corner detail applications to suit various angles.
The partition system does not require any punch tooling, all straight cuts & the profiles all clip on together for quick & easy installation while been able to use 6 or 8 mm thick glass.
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
3
PROFILE IDENTIFICATIONINFINITY SYSTEM PROFILES
DIE No. W57357 Infin FrameDIE No. W35297 Infin Frame Clip
DIE No. W35291 Infin Double Bead DIE No. W35290 Infin Single Bead
DIE No. W35298 Infin Sill DIE No. W35292 Infin Sill Cover
DIE No. W35295Infin Frame
Single Clip
DIE No. W35296Infin Frame
Double Clip
DIE No. W35373Infin Frame
DoorDIE No. W35362
Infin 90 DEG.
Clip-on
DIE No. Not Avail Infin Comp Channel
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
4
PROFILE IDENTIFICATIONINFINITY SYSTEM PROFILES
DIE No. W Infin Corner Profile
DIE No. W Infin Bullnose
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
5
HARDWARE IDENTIFICATIONINFINITY HARDWARE
GSN-IIPInfinity Internal
Partition
1
1
2
2
3
3
4
4
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
Kenny 2014/11/06
DWG NO
TITLE
SIZE
CSCALE
REV
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Kenny 2015/01/15Designed by Checked by Approved by Date
1 / 1 Edition Sheet
Date
1
1
2
2
3
3
4
4
5
5
6
6
AA
BB
CC
DD
Kenny2015/01/15Designed byChecked byApproved byDate
1 / 1 EditionSheet
Date
1
1
2
2
3
3
4
4
5
5
6
6
A
A
B
B
C
C
D
D
Kenny
2015/01/15
Designed by
Checked byApproved by
Date
1 / 1
EditionSheet
Date
1
1
2
2
3
3
4
4
5
5
6
6
A
A
B
B
C
C
D
D
Kenny
2015/01/15
Designed by
Checked byApproved by
Date
1 / 1 Edition
SheetD
ate
GASKETS & SETTING BLOCKS
GSN-GSBSG100GLASS SETTING BLOCKS 100X6
F60-PIG Push-in Gasket
GSL-AL-H602 Y-Seal Gasket
GSL-48EPDMBubble Seal 4.8mm
EPDM
FRC-4812 4.8x12 Pop Rivets
SPIGOTS ETC.
FIXINGS
XXX Infin Spigot
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
6
NOTE: This profile is optional.
MACHINING DETAILSFRAME PROFILES
DIE No. Not Avail. Infin Comp ChannelDrawing not to scale.
Holes to suit fixings
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
7
MACHINING DETAILSFRAME PROFILES
DIE No.W35298 Infin Sill
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
8
MACHINING DETAILSCOVER PROFILES
DIE No. W35292 Infin Comp ChannelDrawing not to scale.
NOTE: The ‘V’ groove is to be close to the topend as this serves as a guide line to machine for electrical plug covers.
Drawing not to scale.
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
9
MACHINING DETAILSFRAME PROFILES
DIE No. W57357 InfinFrameDrawing not to scale.
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
10
MACHINING DETAILSFRAME PROFILES
DIE No. W57357 InfinFrameDrawing not to scale.
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
11
MACHINING DETAILSBEAD PROFILES
DIE No.W35290 Infin Single BeadDrawing not to scale.
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
12
MACHINING DETAILSBEAD PROFILES
DIE No.W35291 Infin Double BeadDrawing not to scale.
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
13
MACHINING DETAILSCLIP-ON PROFILES
DIE No.W35296 Infin Frame
Double Clip
Drawing not to scale.
DIE No.W35295 Infin Frame
Single Clip
DIE No.W35297 Infin Frame
Clip
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
14
FORMULASHORIZONTAL GLASS CUTTING SIZES
Drawing not to scale.
MACHINING DETAILS
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
15
MACHINING DETAILS
Drawing not to scale.
VERTICAL GLASS CUTTING SIZES
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
16
MACHINING DETAILS
Drawing not to scale.
GASKET & GLASS CHART
Push-in Gasket Infinity Internal Gasket Bubble Seal
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Kenny 2015/02/12Designed by Checked by Approved by Date
1 / 1 Edition Sheet
Date
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
17
MACHINING DETAILSHORIZONTAL BEAD CUTTING SIZES
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
18
MACHINING DETAILSVERTICAL BEAD CUTTING SIZES
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
19
MACHINING DETAILSVERTICAL CLIP-ON PROFILES CUTTING SIZES
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
20
MACHINING DETAILS
NOTE: The ‘V’ groove on the inside of the coveridentifies the max. height to machine for plugswithout interfering with the sill.
Drawing not to scale.
SILL COVER
NOTE: When joining 2 sill covers together,insert 38 x 1.5 x 97 flat bar as shown(Die No. W28905)
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
21
TYPICAL DETAILS
Drawing not to scale.
DOOR JAMB DETAIL
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Kenny 2015/02/11Designed by Checked by Approved by Date
1 / 1 Edition Sheet
Date
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
22
TYPICAL DETAILS
Drawing not to scale.
DOOR JAMB DETAIL
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Kenny 2015/02/11Designed by Checked by Approved by Date
1 / 1 Edition Sheet
Date
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Kenny 2015/02/11Designed by Checked by Approved by Date
1 / 1 Edition Sheet
Date
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
23
TYPICAL DETAILS
Drawing not to scale.
DOOR HEAD DETAIL
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Kenny 2015/02/11Designed by Checked by Approved by Date
1 / 1 Edition Sheet
Date
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
24
TYPICAL DETAILS
Drawing not to scale.
VERTICAL DETAIL
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Kenny 2015/02/12Designed by Checked by Approved by Date
1 / 1 Edition Sheet
Date
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
25
TYPICAL DETAILS
Drawing not to scale.
CORNER DETAIL
1
1
2
2
3
3
4
4
5
5
6
6
AA
BB
CC
DD
Kenny2015/02/16Designed byChecked byApproved byDate
1 / 1 EditionSheet
Date
This manual must be read in conjunction with the Installation, Cleaning & Maintenance Document and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront.
Disclaimer: The right to make alterations is reserved© 2013 Wispeco (Pty) Ltd, All Rights Reserved
INFINITYInternal Partition System
crealco
PRODUCT MANUAL
26
TYPICAL DETAILS
NOTE: In order for the 2 profiles to rotate to15 degress, both profiles need to be trimmedon the ‘V’ groove as shown.
RADIUS CORNER DETAIL