impulse pluggable description...

MATERIALDESCRIPTION AND

CABLE

ORDERING

USES

GUIDELINES

Molded neoprene, some types available in polyurethane.

(LPIL/LPBH-12 has 16 AWG. contacts.)Up to 750 VDC.Up to 10,000 PSI.

Connectors in this series are molded on a standard 24" lengthof 16 AWG SO cable. IL-5, IL-12, LPIL-5 are molded on a

Light to heavy duty applications.Hazardous environments.

Lubricate mating surfaces with 3M Silicone Spray or equivalent,DO NOT grease! Connectors must be lubricated on a regular basis.

Align index pin prior to mating.Avoid nicks and cuts around contacts as these are the sealingsurfaces.Elastomers can be seriously degraded if exposed to direct sunlight or high ozone levels for extended periods of time.Do not over tighten bulkhead nuts.Do not pull on cable to disconnect.Avoid sharp bends at cable entry to connector.

Locking sleeves are optional, specify when ordering.Bulkhead connectors do not come with nuts and washers. Ifrequired, please specify when ordering.OM connectors do not come with overmolding boots. If required,please specify when ordering.

INFORMATION

NOTE For Mini Wet Pluggable see Technical Bulletin page 65 80

equivalent.Lubricate o-rings with Dow Corning #111 Valve Lubricant or

16878/4 18 AWG.Bulkhead connectors have 12" teflon leads, Type E per MIL

All mounting surfaces require a 32 finish.

Bulkhead connector design open face pressure rated to 5,000 PSI.Contacts gold plated per MIL-G-45204.

standard 24" length of 18 AWG SO cable. LPIL-12 is molded

Custom lengths and cable types are available on request.on a standard 24" length of 20 AWG cable.

Two to twelve contacts, 12 AWG.

For Micro Mini Wet Pluggable see Technical Bulletin page 65 109

Technical Bulletin 65 01 1-800-327-0971 © 2009 Teledyne Impulse rev 1112

WETPLUGGABLE

IMPULSETELEDYNE

PLUGGABLE


WETIL/BH/OM-2/3/4/5IMPULSETELEDYNE

~

IL- -FS*

*BH- -MP

IL- -MP*

BH- -FS*

~ ~

~

STAINLESS

NEOPRENE

NEOPRENE

1.11

.55

.78

1.00 DIA

1.11

.78

O-RING 2-014

12" TEFLONLEADS

7/16-20 UNF-2A

LEADS12" TEFLON

.20

.3

.75 .75

.3

.75 HEX

.20

.75 HEX

7/16-20 UNF-2A

2-014O-RING

2.9MATEDLENGTH

.28

.50

BRASS/STAINLESSSTEEL STEEL

BRASS/

1-800-327-0971

PLUGGABLE

Technical Bulletin 65 11 rev 0109 © 2009 Teledyne Impulse

WETIL/BH/OM-2/3/4/5IMPULSETELEDYNE

OM- -MP

BH-FS, IL-FS, OM-FS

~

~

MATED PRESSURE RATING (psi)

OM-

-FS

*

*

CONTACT~

CONFIGURATION(MP FACE VIEWS)

DUMMY PLUG FOR

FOR BH-FS/MP

BH-MP, IL-MP, OM-MPDUMMY PLUG FOR~

MOUNTING TORQUE

4

3

not to exceed

3 2

1

2

132

10,000

1

100 in lbs

DC- -FS

DC- -MP

14

2

5

GUIDE PIN

4.12

NEOPRENE

BRASS

GUIDE PIN

.25

.63

LEADS

.78

10.1

1.00 DIA

4.12

1.11

BOOT

FIELDINSTALLABLE

BOOTINSTALLABLE

FIELD

NEOPRENELENGTHMATED

GUIDE PIN

* Specify number of contacts.

GUIDE PIN

*

*

NOTE: Delrin locking sleeves available (DLSA-M or F).

NEOPRENE

NEOPRENE

3" TEFLON

.15 DIA

* Dummy Plugs found on page 65 32.

2 CONTACT 3 CONTACT

4 CONTACT 5 CONTACT

Technical Bulletin 65 20 1-800-327-0971

PLUGGABLE

© 2009 Teledyne Impulse rev 0593

WETIL/BH/OM-6/8IMPULSETELEDYNE

~ ~

~

*

*

*

* ~

BH- -FS

IL- -MP

BH- -MP

IL- -FS

STEEL STEEL

.20

3.2MATEDLENGTH

NEOPRENE

NEOPRENE

O-RING 2-017

5/8-18 UNF-2A

1.00 HEX

12" TEFLONLEADS

.50

MATED2.9

LENGTH

1.11

.75

.3 .3

.75

.78

.83

.20

1.11.78

STAINLESS

1.23 DIA

1.00 HEX

5/8-18 UNF-2A

2-017O-RING

LEADS12" TEFLON

.28

.50

BRASS/STAINLESS

BRASS/

~

~

FOR BH-FS/MP


CONTACTCONFIGURATION(MP FACE VIEWS)

DUMMY PLUG FORBH-FS, IL-FS, OM-FS

BH-MP, IL-MP, OM-MPDUMMY PLUG FOR

~OM- -FS*

*OM- -MP~

MOUNTING TORQUE

10,000

DC- -FS

not to exceed

DC- -MP

100 in lbs

BOOT

8

INSTALLABLE

7


1

*

6

5

4 3

2

1 8

7

65

4

3

21

12.1

LENGTHMATED

5.12

1.11

*

FIELD

GUIDE PIN

NEOPRENE

1.23 DIA

BRASS

3" TEFLON

.78.27

.65

5.12

BOOTINSTALLABLE

FIELD

NEOPRENE

NOTE: Delrin locking sleeves available (DLSB-M or F).

NEOPRENE

NEOPRENE

.25 DIA

LEADS

GUIDE PIN

2

3

4

5

6


8 CONTACT

6 CONTACT 8 CONTACT

W/ GUIDE PIN (WH)


PLUGGABLE


WETIL/BH/OM-6/8IMPULSETELEDYNE

~

PLUGGABLE


WETIL/BH/OM-12IMPULSETELEDYNE

IL-12-MP

BH-12-MP

BH-12-FS

IL-12-FS

STAINLESS12" TEFLONLEADS

.3

.75

.20

O-RING 2-017

5/8-18 UNF-2A

1.00 HEX.75

.3

LEADS

1.00 HEX

5/8-18 UNF-2A

2-017O-RING

12" TEFLON

.20

LENGTH

3.2MATED

.36

.25

.50

.13.25

.38

.38

.25.13

1.06

.50

.25

.36

1.06

1.82 DIA

.28

.50


BRASS/

PLUGGABLE


WETIL/BH/OM-12IMPULSETELEDYNE


~

DUMMY PLUG FORBH-MP, IL-MP, OM-MP

BH-FS, IL-FS, OM-FSDUMMY PLUG FOR

(MP FACE VIEW)

MOUNTING TORQUE


CONTACT

~OM-12-MP

~

OM-12-FS

1.82 DIA

~

CONFIGURATION

FOR BH-FS/MP

DC-12-FS

DC-12-MP

not to exceed

10,000

100 in lbs

13.2

41

3

2

5

12

11

10

98 7 6

NEOPRENE

INSTALLABLEFIELD

BOOT

5.12

NEOPRENE

FIELDINSTALLABLE

BOOT

5.12

.65

.27

LEADS3" TEFLON

BRASS

MATEDLENGTH

NEOPRENE

NOTE: Delrin locking sleeve available (DLSC-M or F).

NEOPRENE

.25 DIA

12 CONTACT

CONTACTS

~

*SPECIFY NUMBER OF CONTACTS

2/3/4/5

6/8CONTACTS


3.65

WET

1.11

.78-FS

3.43

1.00 DIA

DC-*

3.73

1.11-MP

NEOPRENE

-FS

-MP

1.23 DIA

DC-*

.78

NEOPRENE


PLUGGABLEDC-2/3/4/5/6/8

DC-*

DC-*

3.35

IMPULSETELEDYNE

1.1.76

1-800-327-0971Technical Bulletin 65 33 rev 0109 © 2009 Teledyne Impulse

DC-12-MP

DC-12-FS

PLUGGABLEDC-12

1.82 DIA

4.05

WET

3.70

IMPULSETELEDYNE

rev 0697Technical Bulletin 65 35 © 2009 Teledyne Impulse1-800-327-0971

DELRIN LOCKING SLEEVESIMPULSETELEDYNE

6,8, M12, 16,

DLSA-M DLSA-F

DLSB-M DLSB-F

2,3,4,5,7,9 contact

MALE FEMALE

12 contactDLSC-FDLSC-M

HD 2/4 contact

1.29

.94

.94

.76

1.39 DIA

1.62 DIA

2.39 DIA

1.13

1.29

1-800-327-0971 © 2009 Teledyne Impulse

IMPULSETELEDYNE

THIS PAGE INTENTIONALLY LEFT BLANK

1-800-327-0971

PLUGGABLE

Technical Bulletin 65 36 © 2009 Teledyne Impulse rev 0109

WETBH-2/3/4/5 EXTIMPULSETELEDYNE

GUIDE PIN

NEOPRENE

GUIDE PIN

.50

.78

7/16-20 UNF-2A

STAINLESS

GUIDE PIN

STEEL

BRASS/

2-014O-RING .75 HEX

12" TEFLON 12" TEFLON

GUIDE PIN

LEADS

STAINLESSSTEEL

7/16-20 UNF-2A

BRASS/

2-014O-RING .75 HEX

.30

.75

.50

.75

.30

LEADS

.47

.81

1.00 DIA

1.11

2

2

1

2

3

BH- -FS EXT

BH- -MP EXT

3

41

23

54

1

1

2 CONTACT

4 CONTACT

3 CONTACT

5 CONTACT

*

~


*~

CONTACT

For dummy connectors see page 65 32Delrin locking sleeves available (DLSA-M or F) see Page 65 35

NOTE: For mating connectors see page 65 10

For dummy connectors see page 65 32Delrin locking sleeves available (DLSB-M or F) see Page 65 35

O-RING

STEEL

NEOPRENE

5/8-18 UNF-2A

BRASS/STAINLESSSTEEL

1.00 HEX

STAINLESS

2-017

.78

BRASS/

2

5/8-18 UNF-2A

O-RING 2-017

1.00 HEX

12" TEFLONLEADS

12" TEFLONLEADS

.75

.30

.50

.75

.30

.50

.47.81

1.25 DIA

NOTE: For mating connectors see page 65 20

6

7

GUIDE PIN

8

4

5

3

1

2

GUIDE PIN

4

6

5

3

2

1

6

7

8

54

13

1.11BH- -MP EXT

BH- -FS EXT

W/ GUIDE PIN (WH)

6 CONTACT

8 CONTACT

8 CONTACT

**

(MP FACE VIEWS)

~ ~

CONFIGURATIONCONTACT

1-800-327-0971

PLUGGABLE

Technical Bulletin 65 37 rev 0109 © 2009 Teledyne Impulse

WETBH-6/8 EXTIMPULSETELEDYNE

2 CONTACT

.55

1.22

.87 DIA

NEOPRENE

12" TEFLONLEADS

BRASS

7/16-20 UNF-2A

2-014

21

GUIDE PIN

2-014

7/16-20 UNF-2A

BRASS

LEADS12" TEFLON

NEOPRENE

O-RING

1.22

.87 DIASURFACE

MOUNTING

.65

.50

.87

.50

.65

O-RING

.87

1.63

1.63

.87

NEOPRENE

NEOPRENE

.50.28

MOUNTINGSURFACE


MOUNTING TORQUE

DUMMY PLUG FORLPBH-2-MP, LPIL-2-MP

LPBH-2-FS, LPIL-2-FSDUMMY PLUG FOR

(MP FACE VIEW)CONFIGURATION


CONTACT

~LPBH-2-MP

LPBH-2-FS~

LPIL-2-FS

LPIL-2-MP

~

~

FOR LPBH-FS/MPnot to exceed

LPDC-2-FS

LPDC-2-MP

NOTE: Bulkhead body available in stainless steel.Standard 1/2" thread length.

10,000

100 in lbs

IMPULSETELEDYNE

PLUGGABLE SERIES


LOW PROFILE WETLPBH/LPIL-2

PLUGGABLE SERIES


LOW PROFILE WETLPBH/LPIL-3/4/5IMPULSETELEDYNE

~

~

~LPBH-3/4/5-FS

3 CONTACT

LPBH-3/4/5-MP~

MOUNTING TORQUE

CONTACT


4 CONTACT


DUMMY PLUG FORLPBH-3/4/5-FS, LPIL-3/4/5-FS

LPBH-3/4/5-MP, LPIL-3/4/5-MPDUMMY PLUG FOR

LPIL-3/4/5-FS

LPIL-3/4/5-MP

FOR LPBH-FS/MP

5 CONTACT

not to exceed

10,000

Standard 1" thread length.NOTE: Bulkhead body available in stainless steel.

LPDC-3/4/5-MP

LPDC-3/4/5-FS

100 in lbs

.98

.65

.98

3

NEOPRENE

.98

1.63

1.63

.55

2-014O-RING

O-RING 2-014

1.25

12" TEFLONLEADS

BRASS

NEOPRENE

7/16-20 UNF-2A

112

MOUNTING

432

7/16-20 UNF-2A

NEOPRENE

BRASS

LEADS12" TEFLON

1.25

MOUNTINGSURFACE.87 DIA

NEOPRENE

.65

.28.50

1.00

1.00 .87 DIASURFACE

5

21 3

4



PLUGGABLE SERIES


LOW PROFILE WETLPBH/LPIL-7IMPULSETELEDYNE

~

DUMMY PLUG FORLPBH-7-MP, LPIL-7-MP

LPBH-7-FS, LPIL-7-FS

MOUNTING TORQUE



CONTACT

~

~LPBH-7-MP

LPBH-7-FS

DUMMY PLUG FOR

LPIL-7-

FSLPIL-7-

MP

~

FOR LPBH-FS/MPnot to exceed

LPDC-7-FS

LPDC-7-MP

10,000

100 in lbs


.98

NEOPRENE


1.22 NEOPRENE

LEADS12" TEFLON

BRASS

7/16-20 UNF-2A

2-014O-RING

.87

.98

17 6 5

432

O-RING 2-014

NEOPRENE1.72

1.00

2.15

MOUNTING

.73

1.72

NEOPRENE

.28.50

.87

12" TEFLONLEADS

7/16-20 UNF-2A

BRASS

1.00

.87 DIASURFACE1.00

7 CONTACT

PLUGGABLE SERIES


LOW PROFILE WETLPBH/LPIL-9/12IMPULSETELEDYNE

LPBH- -FS

~

~

LPIL- -

FSLPIL- -

MP

~*

LPBH- -MP

~

CONTACT


CONFIGURATION(MP FACE VIEW)

DUMMY PLUG FORLPBH-9-FS, LPIL-9-FS

LPBH-9-MP, LPIL-9-MPDUMMY PLUG FOR

FOR LPBH-FS/MPMOUNTING TORQUE

*

**

not to exceed

10,000

LPDC-9-MP

LPDC-9-FS

100 in lbs

SURFACE

NEOPRENE

NEOPRENE

1.66

2.16

1.25.84

1.25

.95

1.00

2-014O-RING

LEADS12" TEFLON

1.00

.95

1.25


1.73NEOPRENE

BRASS

12

54321

9 8 7 6

7/16-20 UNF-2A

BRASS12" TEFLONLEADS

NEOPRENE

O-RING 2-014

2

.87 DIA

1.22

MOUNTING


.28.50

9

7/16-20 UNF-2A

1 6

3 4 5

7 8

10 11


9 CONTACT 12 CONTACT

3.73

1.63

3.73

LPDC-2-FS

3.73

1.63

1.63

.55

LPDC-3/4/5-FS

.55 .98

3.73

1.63

LPDC-3/4/5-MP

.86

LPDC-2-MP

PLUGGABLE SERIESLPDC-2/3/4/5

1-800-327-0971 © 2009 Teledyne Impulse rev 0109

NEOPRENE

Technical Bulletin 65 71

LOW PROFILE WET

NEOPRENE

IMPULSETELEDYNE

1.72

LPDC-7-FS

LPDC-7-MP

.73

1.72

3.75

.98

2.152.15

4.25

NEOPRENE


LPDC-7

© 2009 Teledyne Impulse rev 01091-800-327-0971

PLUGGABLE SERIESLOW PROFILE WET

NEOPRENE

IMPULSETELEDYNE

1.66

9/12

LPDC- -MP9/12

.84 1.25

3.87

LPDC- -FS

2.16

4.25

NEOPRENE


LPDC-9/12


PLUGGABLE SERIESLOW PROFILE WET

NEOPRENE

IMPULSETELEDYNE


MINI WETPLUGGABLE

IMPULSETELEDYNE

Replace o-rings when re-using connectors.

DESCRIPTION ANDMATERIAL

CABLE

USES

GUIDELINES

Molded neoprene or polyurethane.Two to eighteen contacts, 16 AWG.

length of cable, #20 AWG, unless otherwise specified.

or high ozone levels for extended periods of time.

Inline connectors in this series are molded on a standard 24"

16878/4, 18 AWG.

Light to medium duty applications.

DO NOT grease! Connectors must be lubricated on a regular basis.Lubricate mating surface with 3M Silicone Spray or equivalent,

Do not pull on cable to disconnect.

Avoid nicks and cuts around contacts as these are the sealing

Up to 10,000 PSI, mated.

Elastomers can be seriously degraded if exposed to direct sunlight

Bulkhead connector design open face pressure rated to 5000 PSI.

Connectors should not be allowed to dry out. If this occurssoak in water before use.Do not over tighten bulkhead nuts.

INFORMATION

Avoid sharp bends at cable entry to connector.

ORDERING

surfaces.

Bulkhead connectors do not come with nuts and washers. Nutsand washers should be ordered separately.

Bulkhead connectors have 12" teflon leads, Type E per MIL

equivalent.Lubricate o-ring with Dow Corning #111 Valve Lubricant or

Hazardous environments.


Up to 750 VDC.

Contacts gold plated per MIL-G-45204.

~

~

~

~

PLUGGABLE


MINI WETLPMBH/LPMILIMPULSETELEDYNE

LPMBH-MP

LPMIL-MP LPMIL-FS

LPMBH-FS

.80

.50

SURFACE

1.00

.50

.80

1.18

.78 DIA.SURFACEMOUNTING

.63

.80

NEOPRENE

.50

7/16 X 20UNF 2A

NEOPRENE

BRASS

2-014

12" TEFLONLEADS

O-RING

.50.25

1.18

2-014

12" TEFLONLEADS

O-RING

BRASS

NEOPRENE

UNF 2A7/16 X 20

.50

.63

1.30

MOUNTING

.78 DIA.

PLUGGABLE


MINI WETLPMBH/LPMILIMPULSETELEDYNE

2#16

(MP FACE VIEWS)CONFIGURATION

LPMBH

CONTACT

3#16 4#16

5#16

6#16 7#16

8#16

DUMMY PLUG FORLPMBH-FS, LPMIL-FS

DUMMY PLUG FORLPMBH-MP, LPMIL-MP

MOUNTING TORQUEMATED PRESSURE RATING (psi)100 in lbs 10,000

LPMDC- -FS LPMDC- -MP

not to exceed

2

78

65

432

32

4

4

12

3

76

545

6

*

1

1 2 332

1

1

GUIDE PIN

53

2

41

NOTE: Standard 1/2" thread length.* Specify number of contacts.

*

1

* Dummy plugs found on page 65 83.

NEOPRENE

LPMDC

-*-

FS

LPMDC

-*-

MP

.80

1.501.18

2.402.40

LPMDC WITH 'T' HANDLE

1.00 .50 .50

1-800-327-0971

PLUGGABLE


MINI WETLPMDCIMPULSETELEDYNE


1-800-327-0971 © 2009 Teledyne Impulse

IMPULSETELEDYNE

THIS PAGE INTENTIONALLY LEFT BLANK

PLUGGABLE


WETMIL/MBH/MOM-7/9IMPULSETELEDYNE

~

~ ~

~

*MIL- -FS

MBH- -MP

MIL- -MP

MBH- -FS

**

*

LENGTH

NEOPRENE

NEOPRENE

1.11

.55

.78

1.00 DIA

1.11

.78

O-RING 2-014

12" TEFLONLEADS

7/16-20 UNF-2A

LEADS12" TEFLON

.20

.3

.75 .75

.3

.75 HEX

.20

.75 HEX

7/16-20 UNF-2A

2-014

STAINLESS

2.9MATED

.25

O-RING

.50


BRASS/


PLUGGABLE

rev 0109 © 2009 Teledyne Impulse


(MP FACE VIEW)

CONTACT

DUMMY PLUG FOR


~

MBH-MP, MIL-MP, MOM-MP

MOUNTING TORQUE

MBH-FS, MIL-FS, MOM-FS

FOR MBH-FS/MP

~

MOM- -MP

DUMMY PLUG FOR~

CONFIGURATION

~

*

63

92

*

MDC- -MP

100 in lbsnot to exceed

*

MOM

- -

FS

7

MDC- -FS

10,000

2

1

3

4

8

7

1

5 45

6

*

LENGTHMATED

FIELD

4.12NEOPRENE

NEOPRENE

NEOPRENE

BRASS

10.1

.25

.63

LEADS

.78

3" TEFLON

1.00 DIA

4.12

1.11

BOOT

FIELDINSTALLABLE

BOOTINSTALLABLE

NOTE: Delrin locking sleeves available (DLSA-M or F).

NEOPRENE

.15 DIA

9 CONTACT 7 CONTACT

* Dummy plugs found on page 65 97* Specify number of contacts.

PLUGGABLE



~

~ ~

~

*MBH- -FS

MIL- -MP

MBH- -MP

MIL- -FS*

*

*

.20

3.22.9

12" TEFLON

NEOPRENE/

O-RING 2-017

5/8-18 UNF-2A

1.00 HEX

12" TEFLONLEADS

LENGTHMATED

LENGTH

.50

1.11

.75

.3 .3

.75

.78

.83

MATED

1.11.78

POLYURETHANE

1.23 DIA

1.00 HEX

5/8-18 UNF-2A

2-017O-RING

LEADS

.20

.25

.50


STAINLESSBRASS/

POLYURETHANE

NEOPRENE/

PLUGGABLE

Technical Bulletin 65 91 1-800-327-0971 rev 0109 © 2009 Teledyne Impulse


~

DUMMY PLUG FOR

FOR MBH-FS/MP

~


CONTACTCONFIGURATION

~ (MP FACE VIEW)

MBH-FS, MIL-FS, MOM-FS

MBH-MP, MIL-MP, MOM-MPDUMMY PLUG FOR

~

MOUNTING TORQUE100 in lbs

not to exceed

MOM-12-MP

*

10,000

MDC- -MP

MDC- -FS

MOM-12-FS

*

8

INSTALLABLE

10

BOOT

12.1

LENGTHMATED

5.12 INSTALLABLE

1.11

FIELD

16

NEOPRENE

1.23 DIA

BRASS

3" TEFLON

.78.27

.65

5.12

12

9

FIELD

NEOPRENE


NEOPRENE

NEOPRENE

.25 DIA

LEADS

1

2

3

4

5

6

7

8

910

11

11 1

2

3

4

12

6

15

13

14

BOOT

57


12 CONTACT

16 CONTACT(MOM NOT AVAILABLE)

* Dummy plugs found on page 65 97

~

~

~

MIL-18-MP

MBH-18-MP

MIL-18-FS

DUMMY PLUG FORMBH-MP, MIL-MP

MBH-FS, MIL-FSDUMMY PLUG FOR


18 CONTACT


CONTACT

MOUNTING TORQUEFOR BH-FS/MP

MBH-18-FS

not to exceed

MDC-18-FS

MDC-18-MP

10,000

100 in lbs

1

12" TEFLONLEADS

O-RING 2-017

5/8-18 UNF-2A

1.00 HEX

BRASS/STAINLESSSTEEL

POLYURETHANE

Dummy plugs found on page 65 98

2

3

45

678

9

10

1112

13

14

1516

17

.75

.30

1.88

MATED4.9

LENGTH 1.81 DIA

.50

.25

.88

3.0POLYURETHANE

NOTE: Delrin locking sleeve available (DLSD-M or F).

PLUGGABLE


WETMIL/MBH-18IMPULSETELEDYNE

1.23 DIA

1.00 DIA

MDC-*-MP

1-800-327-0971 rev 0109

3.72

12/16CONTACT

PLUGGABLEMDC-7/9/12/16

MDC-*-FS1.11

3.75

NEOPRENE/


POLYURETHANE

MDC-*-MP

MDC-*-FS1.11

WET

© 2009 Teledyne Impulse

NEOPRENE

.78

.78

CONTACT

3.42

3.38

7/9

*Specify number of contacts

IMPULSETELEDYNE

5.31

MDC-18-FS

1.81 DIA

MDC-18-MP

5.31

MDC-18


PLUGGABLE


WET

POLYURETHANE

IMPULSETELEDYNE

2.462.46

1.31 1.38

2.0 HEX 2.0 HEX

FEMALE

DLSD-F

MALE

DLSD-M

LOCKING SLEEVES FOR:MBH/MIL-18-FS/MP


DELRIN LOCKING SLEEVES IMPULSETELEDYNE

1-800-327-0971

CONNECTORS


GEOPHYSICALHDBH-2/4IMPULSETELEDYNE

~

*

*

~

*

~

HDBH- -FS

MULTI-LAM

.3

.75

TEFLON LEADS

STEEL

BRASS/

LENGTH

BRASS/

2.50

O-RING 2-017

5/8-18 UNF-2A

1.00 HEX

24" 14 AWGTEFLON LEADS

HD- -FS

2-017

.3

NEOPRENE

.75

.20

1.11

.78

.20

1.23 DIA

1.00 HEX

5/8-18 UNF-2A

O-RING

NEOPRENE

CONTACT

STAINLESSSTEEL

HDBH- -MP

STAINLESS

1.11

NEOPRENE

CONTACT SIZE AND STRAIN RELIEFDESIGNED FOR THE MOST DEMANDINGAPPLICATIONS.

SHOCK IMPACT.NO RIGID PARTS TO BREAK ON

24" 14 AWG

4.90MATED

1.00 DIA

DUMMY PLUG FOR


CONTACTCONFIGURATION(MP FACE VIEWS)

DUMMY PLUG FORHDBH-FS, HD-FS

HDBH-MP, HD-MP

FIB

~HD- -FS FIB

*HD- -MP~

~

FOR HDBH-FS/MPMOUNTING TORQUE

*

FIELD

GUIDE PIN


*

*

2 112.1

LENGTHMATED

5.12

1.11

POLYURETHANE

NEOPRENE

1.23 DIA

3

.60

.30

5.12

BOOTINSTALLABLE

.77

NEOPRENE


NEOPRENE BOOT

NEOPRENE

2 1

4

POTTING COMPOUND

not to exceed

10,000

4 #102 #10

HDDC- -MP

HDDC- -FS

100 in lbs


CONNECTORS


GEOPHYSICALHD-2/4-FIBIMPULSETELEDYNE

1.23 DIA

**1.1.78


3.403.80

CONNECTORSHDDC-2/4

HDDC- -MPHDDC- -FS

NEOPRENE

GEOPHYSICAL

*Specify number of contacts

IMPULSETELEDYNE

DESCRIPTION ANDMATERIAL

CABLE

USES

GUIDELINES

Molded neoprene or polyurethane.Two to eight contacts.Up to 750 VDC.Up to 10,000 PSI, mated.

Inline connectors in this series are molded on a standard 24"length of cable, 20 AWG, unless otherwise specified.

Light to medium duty applications.Hazardous environments.

Lubricate mating surface with 3M Silicone Spray or equivalent,DO NOT grease! Connectors must be lubricated on a regular basis.

Avoid nicks and cuts around contacts as these are the sealingsurfaces.Elastomers can be seriously degraded if exposed to direct sunlightor high ozone levels for extended periods of time.Do not over tighten bulkhead nuts.

Do not pull on cable to disconnect.Avoid sharp bends at cable entry to connector.

ORDERINGINFORMATION

Bulkhead connectors do not come with nuts and washers. Nutsand washers should be ordered separately.

Bulkhead connectors have 12" teflon leads, Type E per MIL

equivalent.Lubricate o-ring with Dow Corning #111 Valve Lubricant or

16878/4, 20 AWG, (2-4, 9-18 contact) or 22 AWG (5-8 contact).


Replace o-rings when re-using connectors.

Bulkhead connector design open face pressure rated to 5000 PSI.Contacts gold plated per MIL-G-45204.

Grip main body of connector during mating or unmating.

MCOM connectors have 12" teflon leads, Type E per MIL 16878/4,20 AWG (2-4 contact) or 22 AWG (5-8 contact)


MICRO MINI WETPLUGGABLE

IMPULSETELEDYNE

MCIL- -FS*

MCBH- -MP*

MCIL- -MP*

MCBH- -FS*

NEOPRENE

NEOPRENE

7/16-20 UNF-2A

12" TEFLONLEADS

.50

LENGTHMATED2.9

.99

1.10

.62 DIA.

ALUMINUM/TITANIUM

BRASS/

2-014O-RING

.75 HEX.31 .37

.15

LEADS12" TEFLON

.50

.31

BRASS/

ALUMINUM/TITANIUMSTAINLESS STEEL/

.75 HEX

O-RING 2-014

7/16-20 UNF-2A

.37

.41

LENGTHMATED2.9

.75

1.10

.25

.25

STAINLESS STEEL/


MICRO MINI WETPLUGGABLEMCIL/BH/OM-2/3/4 IMPULSE

TELEDYNE


MOUNTING TORQUEFOR MCBH-FS/MP

DUMMY PLUG FOR

MCIL/BH-FSDUMMY PLUG FOR



MCDC- -FS

MCDC- -MP

10,000

*

*


CONTACT

FEMALEMALE

MCDLS-M MCDLS-F

.87

.50 1.62

MCIL/BH-MP

NOTE: Bulkhead body available in Titanium.Standard 3/4" thread length.

1.25.75

.70

Ø.62

2.50"

BRASSNEOPRENE

#20 AWGTEFLON LEADS

1.48

.99

.70

Ø.62

BRASSNEOPRENE

2.50"

#20 AWGTEFLON LEADS

MCOM-*-MP

MCOM-*-FS

W/ GUIDE PIN4 #12

GUIDE PIN

1

2

4

3

GUIDE PIN

3 #12W/ GUIDE PIN

2

13

W/ GUIDE PIN2 #12

GUIDE PIN

12



TELEDYNE

MCIL- -FS*

MCBH- -MP*

MCIL- -MP*

MCBH- -FS*

NEOPRENE

NEOPRENE

7/16-20 UNF-2A

12" TEFLONLEADS

.50

LENGTHMATED2.9

.99

1.10

.62 DIA.

STAINLESS STEEL/ALUMINUM/TITANIUM

BRASS/

2-014O-RING

.75 HEX.31 .37

.15

LEADS12" TEFLON

.50

.31

BRASS/

ALUMINUM/TITANIUM STAINLESS STEEL/

.75 HEX

O-RING 2-014

7/16-20 UNF-2A

.37

.41

LENGTHMATED2.9

.75

1.10

.37

.20



TELEDYNE


MOUNTING TORQUEFOR MCBH-FS/MP

DUMMY PLUG FOR

MCIL/BH-FSDUMMY PLUG FOR



MCDC- -FS

MCDC- -MP

10,000

*

*5 #15


CONTACT

FEMALEMALE

MCDLS-M MCDLS-F

.87

.50 1.62

MCIL/BH-MP

2

3

1

4 5

6

7

5

4

6 1

5

2

3

3

4

18 2

6 #15 8 #15


1.25.75

.70

Ø.62

2.50"

BRASSNEOPRENE

#22 AWGTEFLON LEADS

1.48

.99

.70

Ø.62

BRASSNEOPRENE

2.50"

#22 AWGTEFLON LEADS

MCOM-*-MP

MCOM-*-FS


MICRO MINI WETPLUGGABEMCIL/BH/OM-5/6/8 IMPULSE

TELEDYNE

*

*

*.5

*MCIL- -FS

MCBH- -MP MCBH- -FS

MCIL- -MP

.75

LEADS12" TEFLON

LEADS12" TEFLON

1/2-20 UNF-2A

BRASS/STAINLESS STEEL

O-RING 2-015

.81 HEX .81 HEX

1/2-20 UNF-2A

2-015O-RING

STAINLESS STEELBRASS/

.75

LENGTH

.75

.5

1.10

NEOPRENE

NEOPRENE

.20

.37

.75

.90

1.12

.90

1.00 DIA

3.2MATEDLENGTH

MATED3.2

PLUGGABLE


MICRO MINI WETMCIL/BH-10/12/16/18IMPULSETELEDYNE

CONFIGURATION

10,000

MCDC- -MP

MCDC- -FS

not to exceed100 in lbs

*MCIL/BH-FS


MCIL/BH-MPDUMMY PLUG FOR

*


FOR MCBH-FS/MPMOUNTING TORQUE

DUMMY PLUG FOR

(MP FACE VIEW)

CONTACT

MALE

DLSA-M

.94

1.39 DIA

FEMALE

DLSA-F

1.29

10 #15

10

7

9

8

65

4

12

310

9

8

11

76

5

4

121

23

12

13

14 4

3

1516

9

1110

2

1 8

56

7

12 #15 16 #15


12

35

67

4

89

1817

16

15

1413

12

11

10

18 #15



MICRO MINI WETPLUGGABLEMCIL/BH-10/12/16/18 IMPULSE

TELEDYNE

CONFIGURATION(MP FACE VIEW)

CONTACT

12" TEFLONLEADS

2

89

1 3 4

7 6

5

10,000

MCLPDC- -MP

MCLPDC- -FS

not to exceed100 in/lbs

MCLPIL/BH-MP *

NOTE: Bulkhead body available in Stainless Steel.

Dummy plugs found on page 65 127


DUMMY PLUG FORMCLPIL/BH-FS

DUMMY PLUG FOR

*

FOR MCLPBH-FS/MPMOUNTING TORQUE

MCLPIL-9-MP

MCLPIL-9-FS

MCLPBH-9-MP

MCLPBH-9-FS

.99

O-RING2-014

O-RING2-014

12" TEFLONLEADS

BRASS

7/16-20 UNF-2A

MOUNTING SURFACE.87 DIA

MOUNTING SURFACE.87 DIA

7/16-20 UNF-2A

BRASS

.50

.61

1.36

.50

.61

.99

1.10 NEOPRENE

NEOPRENE

1.691.69

.99.55 .99

1.441.44

NEOPRENE

NEOPRENE

Standard 1/2" thread length.


MICRO MINI WETPLUGGABLEMCLPBH/MCLPIL-9 IMPULSE

TELEDYNE

.62 DIA

CONTACT


2/3/4


PLUGGABLEMCDC-2/3/4/5/6/8

.62 DIA

3.35

MICRO MINI WET

-FS

.99

3.15

MCD

C-* -

MP

.75

MCD

C-*

-FS

.99

3.35

NEOPRENE

MCD

C-* -MP

.75

3.15

NEOPRENE

MCD

C-*

CONTACT

5/6/8

* Specify number of contacts

IMPULSETELEDYNE

3.65


-MP


PLUGGABLEMCDC-10/12/16/18

1.00 DIA

4.02

1.12.75

* Specify number of contacts

MICRO MINI WET

-FS

MCD

C-*

MCD

C-*

NEOPRENE

IMPULSETELEDYNE

IMPULSETELEDYNE


PLUGGABLE


MICRO MINI WETMCLPDC

1.501.75

.55.99 .55.99

1.75

NEOPRENE

MCLPDC-9-MPMCLPDC-9-FS

.29 .29


DUMMY PLUG FOR

.50.50

1.00

RMH-2-FS/MP

1.00

10,000

RMHDC-2-FS/MP

RMHDC-2-FS/MP

.28

NEOPRENE

IN2T CABLE

.50

RMH-2-FS/MP

NEOPRENE

PLUGGABLE


WETRMH-2-FS/MPIMPULSETELEDYNE

6501B.PDFSheet1Drawing View1

6599A.pdfSheet1



65111B.pdfSheet1Drawing View2








impulse pluggable description...

Documents