improving efficiency of dewatering alternatives to ... dewatering... · belt press centrifuge screw...
TRANSCRIPT
Improving Efficiency of DewateringAlternatives to Conventional Dewatering
Technologies
Robert Gillette, PE, BCEESteve Swanback, PE
Rebecca Overacre, PE
2009 PNCWA Webinar Recent Developments In
Biosolids Management Processes
sgs809pncwa.ppt/2
Outline
1. Screw press technologya. Performance survey resultsb. Pilot testing resultsc. Lifecycle cost evaluation (Class A and Class B)d. Design considerations
2. Rotary fan press technologya. Performance survey resultsb. Pilot testing resultsc. Lifecycle cost evaluation (Class A and Class B)d. Design considerations
3. Overview of R&D Technologies
sgs809pncwa.ppt/3
Screw Press Technology
sgs809pncwa.ppt/4
Screw Press Manufacturers
• Huber (inclined)
• FKC (horizontal)
Screw Press General Description
Dewatering by Volume Reduction
Screw Press Expanded View
Screw Press Expanded ViewClass A Option
sgs809pncwa.ppt/9
Flow Schematic
sgs809pncwa.ppt/10
Tallahassee, FL, FKC InstallationTallahassee, FL, FKC Installation
FKC Screw Press
sgs809pncwa.ppt/11
FKC Screw Press
Petaluma, CA, FKC InstallationPetaluma, CA, FKC Installation
sgs809pncwa.ppt/12
Huber Press
Magna, UT, Huber InstallationMagna, UT, Huber Installation
sgs809pncwa.ppt/13
Huber Press
Maine, Huber InstallationMaine, Huber Installation
sgs809pncwa.ppt/14
Performance Survey
sgs809pncwa.ppt/15
Survey of 22 Full Scale Installations –The Cake Solids Concentration Depends on Type of Sludge
Type of Sludge Screw Press Cake (% solids)FKC 15 – 20
FKC (with steam and lime) 20 – 45Huber 12 – 20FKC 21 – 28
WAS
Huber 22 – 25Raw Huber 18 – 40
PS+WASFKC > 18
Huber 19 – 24Aerobically Digested
Anaerobically Digested
FKC 17 – 25Anaerobically Digested Huber 13 – 16
Raw
sgs809pncwa.ppt/16
Survey of 22 Full Scale Installations –The Median Cleaning Schedule is Once Per Week
Manual Cleaning Schedule(times per month)
0
5
10
15
20
25
30
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22Facility Number
sgs809pncwa.ppt/17
Case Study –St Petersburg, FL
sgs809pncwa.ppt/18
Pilot Results - Projected Full Performance – St. Petersburg
Manufacturers Recommendations
Screw PressBelt Press CentrifugeClass B Class A
Minimum Cake Solids Concentration (% solids)
18 21 16 33
Maximum Polymer Dosage (lb/DT)
19 25 30 33
Minimum Solids Capture (%)
95 95 90 90
Parameter
sgs809pncwa.ppt/19
“Relative” Cost Comparison
BFP Centrifuge Screw Press
Capital Cost $ $$$ $$
Building Modifications $ $$ $$
Odor Control $$$ $ $
Power $ $$$ $
Maintenance $$ $$ $
Chemical $$ $$$ $$
Hauling $$ $ $$
Disposal $$ $ $$
sgs809pncwa.ppt/20
Performance Comparison
Will Vary Depending on Conditions!!!Will Vary Depending on Conditions!!!
BFP Centrifuge Screw Press
% Solids Produced ++ +++ +
Filtrate/Centrate Quality ++ ++ +
Reliability ++ ++ +++
Operator Attention Required + ++ +++
Ease of startup and shutdown ++ + ++
sgs809pncwa.ppt/21
Design Considerations
sgs809pncwa.ppt/22
Design Considerations
• Lead time (from Japan or Germany): prepurchase?
• Custom design – varying dimensions until shop drawing
• Performance guarantee and penalty for non-compliance
• Basis of design– Loading & capacity: pilot test– Run time, unattended operation
• Effect of rising steel costs – units all SST
sgs809pncwa.ppt/23
Design Considerations, Continued
• Need headroom if RST on mezzanine• Monorail/overhead crane• Building considerations – footprint
requirement – or outside• Provision for Class A in future• Cake conveyance options affects layout
sgs809pncwa.ppt/24
Design Parameters
• Range of Capacity: Up to 8.5 DT/day– At “nominal” speed
• RST output (% Solids): around 4%• Screw Press output (% Solids): 15 – 28%• Polymer consumption: 20 – 40 lb/DT• Detention time: approximately 4 hours• Motor speed: as low as 0.3 rpm• Motor HP – largest unit is 7.5 HP
sgs809pncwa.ppt/25
Rotary Press Technology
sgs809pncwa.ppt/26
Rotary Press Manufacturers
Fournier
Prime Solutions
sgs809pncwa.ppt/27
Rotary Press Schematic
sgs809pncwa.ppt/28
Process Cutaway
sgs809pncwa.ppt/29
Design Parameters
• Range of Capacity: 7-250 gpm• Cake % Solids: 12 – 28%• Detention time: N/A• Motor speed: as low as 1-3 rpm• Motor HP: 5-20 HP
sgs809pncwa.ppt/30
Fournier Rotary Press
sgs809pncwa.ppt/31
• Size Compared to Other Technologies
sgs809pncwa.ppt/32
Multiple Channels on Single Drive
sgs809pncwa.ppt/33
Fournier Rotary Press Pilot Test
sgs809pncwa.ppt/34
Prime Solutions Rotary Fan Press
sgs809pncwa.ppt/35
Performance Survey
sgs809pncwa.ppt/36
Survey Results
Facility EquipmentFacility
Size (mgd)
Solids Type Incoming % TS
Discharge % TS
Raiford, FL Prison WWTP
Rotary fan press 1.1 Extended aeration
1.6-2.5 19-22
Front Royal, VAMunicipal WWTP
Rotary fan press 3.3 Thermophilic Anaerobic Digestion
3.5 25
Fairfield, CAMunicipal WWTP
Rotary fan press 15.5 Conventional Anaerobic Digestion
2 17
Lafayette, TNMunicipal WWTP
Rotary press 0.5 Conventional Anaerobic Digestion
1.0-1.5 25
Portland, MEMunicipal WWTP
Rotary press 19.8 Thickened PS/WAS
3-6 19-25
Hampton, NHMunicipal WWTP
Rotary press 2.5 Septage/PS/WAS
6-8 26-28
Murfreesboro, TNMunicipal WWTP
Rotary press 15 PS/WAS 0.8-1 12-14
Scarborough, MEMunicipal WWTP
Rotary press 1.4 Thickened PS/WAS
3 28
sgs809pncwa.ppt/37
Rotary Dewatering Features
• Low speed, low vibration, low shear• Uses less energy than centrifuges or BFPs• Modular• Small footprint• Minimal start-up and shutdown time• Minimal moving parts• Odors contained
sgs809pncwa.ppt/39
R&D Technologies
sgs809pncwa.ppt/40
EKG Technologies
• Electrokinetic Geosynthetics (EKG) Technology– Theory – Electro-osmotic principle
sgs809pncwa.ppt/41
Uses of EKG Technology
• Ashbrook Product– Anaerobically/Aerobically Digested
Sludge• Fresno• England
– Alternative to conventional dewatering
• Siemen’s Product– Secondary dewatering process– Alternative to sludge drying
sgs809pncwa.ppt/42
Siemen’s ELODE Technology
sgs809pncwa.ppt/43
Siemen’s ELODE Technology
sgs809pncwa.ppt/44
Siemen’s ELODE Technology