®

®

© MIS Corporation. All Rights Reserved.

Narrow Platform

The MIS self-tapping SEVEN implants are especially designed for implantation in a wide range of bone types and bone augmentation procedures. Their geometric design includes dual threads, two or three spiral channels stemming from the apex, micro rings on the implant neck and a changing thread thickness along the implant. All MIS SEVEN implants are supplied with a single use final drill for reducing the heat produced during drilling, resulting in an improved osseointegration.

All rights reserved. No part of this publication may be reproduced, transcribed, stored in an electronic retrieval system, translated into any language or computer language, or be transmitted in any form whatsoever, without the prior written consent of the publisher. Warning: Only a licensed dentist should use these products.

Introduction.

MIS is proud to introduce the new addition to our SEVEN

implant range: the SEVEN 3.30mm Narrow platform.

This new Seven 3.30mm implant will be supplied in

varying lengths of 10mm, 11.5mm, 13mm and 16mm.

MIS SEVEN Narrow implant is especially

designed for narrow ridges and tight

spaces and is accompanied by a

variety of prosthetic options specifically

designed for this platform. This propensity

provides many variations with an emphasis on

simplicity and convenience in restoration work.

“...MIS SEVEN Narrow implant is especially designed for narrow ridges and tight spaces...”

1

2

3

4

5

6

7

2

3

1

2.10mm

45

7

0.1mm

0.3mm

6

2mm

5.

Technical info.

2.10mm Int. hex. connection

Surface - sandblasted+acid etched

Conical body

Two spiral channels

Domed apex

Dual thread of 2mm

Micro-rings (0.1x0.3mm)

MF7-10330 MF7-11330 MF7-13330 MF7-16330

6.

1200-1500

Ø1.90

900-1200

Ø2 Ø2 Ø3.20

500-700

Ø2.40

15-25

Ø3.30

200-400

2/3/4mm

Ø 4mm

MC1-00330

MH-N2330MH-N3330MH-N4330

Ø 3.30mm Implant Range.

Ø 3.30mm Implant Procedure.

The procedure recommended by MIS cannot replace the judgment and experience of a surgeon.

Ø 3.30mm

Drill Speed (RPM)

Diameter

* all implants include the relevant cover screw and final drill

Implant’s cover screws and healing caps.Healing cap available in gingival heights: 2,3,4mm

Ø 2.40

Ø 3.30

2.10

Ø 3.30mm

Ø 3.30mm

Ø 3.30mm

Ø 3.30mm

MF7-10330

MF7-11330

MF7-13330

MF7-16330

length 10mm

length 11.50mm

length 16mm

length 13mm

Ø 2.20

Ø 3.20

DimensionsCatalog No. DescriptionMaterial

Final Drill A specially designed final drill for 10mm, 11.50mm, 13mm and 16mm implants is supplied with every implant, allowing a short and safe drilling procedure.

Screw type implant internal hex., NP

SEVEN screw type implants Ø 3.30mm Narrow Platform.

Titanium Alloy Ti 6Al-4V ELI

Sand Blasted Acid-Etched

The Narrow implants are packaged with a connector which is a removable part of the Narrow implant and is adapted to all MIS tools. This connector provides a safe, quick and simple extraction of the implant from the tube and allows an easy detachment from the implant in the end of the surgical procedure, due to an advanced snap system mechanism.

Packaging.

8.

1.

2.

Implant placing with a connector

Implant identificationmarking

Polystyrene tube with titanium sleeve

Connector

Connector detaching

5.

Tools.

Special Direct Tool for Narrow Platform Implants

Regular Delivery Tools for Int. Hex. Connection and Narrow Implant Connector

Long Ratchet Adapter for Int. Hex. Connection, NP

Hex. Ratchet Long Adapter forInt. Hex. Connection

Hand Key for Int. Hex.Connection

MT-MRH20

MT-HHK24

Hex. Ratchet Short Adapter for Int. Hex. Connection

MT-MRH10

Long Motor Adapter for Int. Hex. Connection

MT-MMH20

Short Motor Adapter for Int. Hex. Connection

MT-MMH10

MT-NRH20

9.

Prosthetic.

MIS offers a wide variety of prosthetic abutments

that provides many options, with an emphasis on

simplicity and convenience of restoration work.

12.

MaterialDimensions

Titanium

Plastic

length 8.8mm

length 8mm

Impression Coping for Open Tray, Int. Hex., NP

Impression Coping for Closed Tray, Int. Hex., NP

Stainless steel

length 13mm

Titaniumlength 21mm

Stainless steel

length 11mm

Titaniumlength 16.5mm

Titaniumlength 7.6mm

Closed tray impression coping, NP

Impression coping plastic cap, NP

Direct Impression coping, int. hex., NP

MN-I0330

Direct Impression coping guide pin

MN-G0160

Direct impression coping, int. hex., NP

MN-IT100

Direct impression coping guide pin

MN-GP100

Direct prosthetic screw, int. hex., NP

X 5

X 1

X 1

Direct Impression Coping Set for Closed Tray, Int. Hex., NP (MN-IT300)

i

Prosthetic.

Availability from January 2011

Prosthetic Options.

5.5.

MaterialDimensions

Prosthetic Abutments, Int. Hex., NP

Titanium

Plastic

Plastic

length 13mm

length 8mm

length 8mm

Titanium

Titanium

length 6.80mmlength 7.80mmlength 8.80mmlength 9.80mm

length 8.80mmlength 9.80mmlength 10.80mmlength 11.80mm

Cementing post, int. hex., NP

Burn out anti-rotation plastic cup, NP

Burn out plastic cup, NP

MN-MAC10

MN-ICH40

MN-IC040

Anatomic transgingival abutment, int. hex., NP, h=1,2,3,4mm, c=4mm

Anatomic transgingival abutment, int. hex., NP h=1,2,3,4mm, c=6mm

MN-CPK41*MN-CPK42*MN-CPK43*MN-CPK44*

MN-CPK61*MN-CPK62*MN-CPK63*MN-CPK64*

Analogs

Stainless steel

length 12mmImplant analog, int. hex., NP

MN-RSM10

Stainless steel

lenght 15.1mmBall attachment analog

MB-RS375

Ø4mm

All impression copings and abutments include the relevant screw.i

* Includes Burn out anti-rotation plastic cup MN-ICH40

Availability from January 2011

Plastic Cylinders

Angulated Abutments, Int. Hex., NP

Prosthetic Screw

Titanium

Titanium

length 7.6mm

length 10mm

Direct prosthetic screw, int. hex., NP

20° Angulated abutment int. hex., NP

MN-S0160

MN-AN020

Burn-out plastic

length 13mm

Burn-out plastic

length 13mm

Direct plastic cylinder, int. hex., NP

MN-CPH13

Direct plastic cylinder, without int. hex., NP

MN-CP013

MaterialDimensions

14.

Prosthetic.

X 2

X 2

X 2

MaterialDimensions

Plastic

Plastic

height 2.6mm

diameter 15mm

Titaniumlenght 9.60mmlenght 10.60mmlenght 11.60mm

Ball attachment anchor, NP, h=2,3,4mm

MB-N2330MB-N3330MB-N4330

Gold - e

Gold - e

height 2.4mm

height 2.4mm

Gold ball cap

Gold ball cap

MB-GPS10

MB-TTP10

Stainless steel

height 3.2mm

Soft plastic cap for metal housing

Disc for ball attachment to prevent undercut

Metal HousingMB-DMH10

MB-PPR10

MB-DB235

MB-MH100

Ball Attachmentsh

Ø4mm

2.5mm

Plasticheight 2.6mmPlastic ball capMB-SF200

All impression copings and abutments include the relevant screw.i

MIS introduces the Narrow Prosthetic Kit (NPK), a comprehensive set designed for the full restoration of parallel inserted implants. The NPK features ready-made components for an easy impression and transfer, and provides a wide variety of esthetic options for the restorative process.

Availability from January 2011

16.

Narrow Prosthetic Kit.

Crown height 4mm

MK-NPK41MK-NPK42MK-NPK43MK-NPK44

Gingival height 1mmGingival height 2mmGingival height 3mmGingival height 4mm

Crown height 6mm

MK-NPK61MK-NPK62MK-NPK63MK-NPK64

Gingival height 1mmGingival height 2mmGingival height 3mmGingival height 4mm

Kit Options:

Crown height 6mm

Crown height 4mm h

Ø

Titanium

Anatomic cementing transgingival abutment

MN-CPK41

Plastic

Impression coping plastic cap

Material:

Material:

Dimensions:

MN-IC600

Stainless steel

Implant analog internal hex. Narrow platform

MN-RSM40

Titanium

Direct prosthetic screw

MN-S0160

Height 1mm, Ø4

Plastic

Plastic healing cap

Titanium

Anatomic cementing transgingival abutment

MN-CPK42

MN-CHC40

Height 2mm, Ø4

Burn out plastic

Burn out anti-rotation plastic cap

Titanium

Anatomic cementing transgingival abutment

MN-CPK43

MN-ICH40

Height 3mm, Ø4

Burn out plastic

Burn out plastic cap

Titanium

Anatomic cementing transgingival abutment

MN-CPK44

MN-IC040

Height 4mm, Ø4

h

Ø

Titanium

Anatomic cementing transgingival abutment

MN-CPK61

Plastic

Impression coping plastic cap

Material:

Material:

Dimensions:

MN-IC600

Stainless steel

Implant analog internal hex. Narrow platform

MN-RSM60

Titanium

Direct prosthetic screw

MN-S0160

Height 1mm, Ø4

Plastic

Plastic healing cap

Titanium

Anatomic cementing transgingival abutment

MN-CPK62

MN-CHC60

Height 2mm, Ø4

Burn out plastic

Burn out anti-rotation plastic cap

Titanium

Anatomic cementing transgingival abutment

MN-CPK63

MN-ICH40

Height 3mm, Ø4

Burn out plastic

Burn out plastic cap

Titanium

Anatomic cementing transgingival abutment

MN-CPK64

MN-IC040

Height 4mm, Ø4

Kit Contents.

All rights reserved. No part of this publication may be reproduced, transcribed, stored in an electronic retrieval system, translated into any language or computer language, or be transmitted in any form whatsoever, without the prior written consent of the publisher. Warning: Only a licensed dentist should use these products.

MC-SNLEN Rev.1

MIS Implants Technologies Ltdwww.mis-implants.com

MIS’s Quality System complies with international quality standards: ISO 13485:2003 - Quality Management System for Medical Devices, ISO 9001: 2008 – Quality Management System and CE Directive for Medical Devices 93/42/EEC. MIS’s products are cleared for marketing in the USA and CE approved.

®