imperial college safety unit - introduction to laser safety - 1 introduction to laser safety ian...
TRANSCRIPT
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 1
Introduction to laser safety
Ian GillettSafety Director
Imperial College
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 2
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 3
What is a laser? The word “laser” is an acronym which stands for Light
Amplification by Stimulated Emission of Radiation. Light energy is amplified to extremely high intensity by a
process called stimulated emission. The energy generated by the laser is in or near the
optical portion of the electromagnetic spectrum.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 4
How does a laser work? Electrons surrounding atoms are excited into higher
energy states to create a “population inversion”. The excited electrons release their energy in the form of
photons which can, in turn, collide with other excited electrons and cause them to release an identical photon - this is called stimulated emission.
As more energy is put in so more photons are released. By reflected the photons back and forth in a mirrored
system the amount of energy can be increased. Some of the energy is allowed to escape through a
partially coated mirror to create a “laser beam”.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 5
Types of laser Gas lasers
• including He-Ne and carbon dioxide lasers
Dye lasers Solid state lasers
• including neodymium-YAG (Nd:YAG) lasers
Semiconductor lasers• diode lasers
Chemical lasers
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 6
Laser light Laser light has the following properties:
• it is monochromatic• it is very intense• it has low divergence• it is coherent.
Lasers can have different types of beam output• continuous wave (CW), or• pulsed.
Laser “speckle” is caused by scattered laser radiation interfering with incident laser radiation.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 7
Beam hazards The laser produces an intense, highly directional beam
of light. This light will be absorbed by surfaces it is directed at, raising the temperature of that surface.
The eyes and skin of the body are vulnerable to this energy.
Of greatest concern is laser exposure in the retinal hazard region, but ultraviolet and infra-red light also have an effect.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 8
The Retinal Hazard Region
400-1400nmAffects the retina
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 9
UV-C (100-280nm)Cornea surface
UV-A (315-400nm)Affects the lens
UV-B (280-315nm)Absorbed by the cornea
Ultraviolet light
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 1
0
Far IRAffects cornea and aqueous humor
Near IR (< 1400nm)Affects the retina
Infra-red Region
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 1
1
Reflections There are two principle types of laser reflection:
• specular reflection - which occurs from mirror-like surfaces. The incident beam striking a specularly reflecting surface will leave it essentially unchanged.
• diffuse reflections - which occur from rough surfaces such as paper or matt-painted walls. These reflections bear no relation to the direction of the incident radiation.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 1
2
Non-beam hazards Non-beam hazards include:
• electrical hazards - especially from trailing cables and risk of water spillages
• fumes - from vaporised target material• laser dyes - many of these are carcinogenic• optical hazards - arising from the flash lamps used to “pump” the
lasers.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 1
3
Safety Standards There are two principle international laser safety
standards:• International Electrotechnical Commission (IEC) 60825 - this has
been adopted in the UK as British Standard BS EN 60825-1:1994 “Safety of laser products. Part 1. Equipment classification, requirements and user’s guide.”
• American National Standards Institute (ANSI) Z136
Both standards share a common classification system for lasers based on their power output, wavelength and pulse duration.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 1
4
British Standard BS EN 60825-1:1994 is divided
into three sections (General; Manufacturing Requirements; and User’s Guide)
The objectives of the Standard are to: • protect persons from laser radiation• lay down requirements for user and
manufacturer to establish procedures
• ensure adequate warning of hazards• reduce possibility of injury, and• protect persons from other hazards.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 1
5
Laser Hazard Classification Exposure limits have been set for nearly all types of
laser radiation. These limits are referred to as Maximum Permissible
Exposures (MPEs). MPEs are those levels of radiation to which persons may
be exposed without suffering adverse effects. MPEs depend upon the wavelength of the laser and the
duration of the exposure. Detailed tables are found in the British Standard.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 1
6
Class 1 MPE less than 7 microwatts of visible radiation. A Class 1 laser is considered “safe” under reasonably
foreseeable conditions of operation and they present no hazard to the eye or skin.
This Class also includes laser systems which cannot emit hazardous levels of laser radiation because of the inherent design of the product.
Note that there may be a more hazardous laser system embedded in the product and additional precautions would be necessary if the system is opened up.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 1
7
Exceed accessible emission limits for Class 1 but, because of the geometrical spread of the emitted radiation, the laser does not cause harmful levels of exposure to the unaided eye.
Safe limit can be exceeded, and injury can occur, if magnifying viewing instruments are used, eg binoculars, telescopes, magnifying glasses, microscopes.
Class 1M
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 1
8
Class 2 MPE less than 1 mW of visible radiation. A Class 2 laser or laser system must only emit a visible
laser beam. Momentary viewing of a Class 2 laser beam is not
considered hazardous since the upper limit for this type of device is less than the MPE for momentary exposures of 0.25 second or less - the so-called “blink reflex”.
Intentional extended viewing is considered hazardous.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 1
9
Class 2M
Laser products which exceed the permitted accessible limits for Class 2 but, because of the geometric spread of the emitted radiation, protection of the unaided eye is normally afforded by natural aversion responses to bright light.
The use of magnifying viewing instruments can give rise to higher levels of exposure and injury can occur. These instruments include: binoculars; telescopes; magnifying lenses; and microscopes.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 2
0
Class 3R Laser products having a level of accessible emission up
to five times the limits for Class 1 (if invisible) or Class 2 (if visible).
The maximum permissible exposure may be exceeded but the risk of injury is low.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 2
1
Class 3B Less than 500 mW of visible radiation
• note that Class 3B also covers pulsed lasers and invisible radiation. Reference should be made to the MPE limits contained in the British Standard in order to verify classification.
Direct intra-beam viewing is always hazardous. Viewing diffuse reflections from a distance is normally
safe provided the exposure duration is less than 10 seconds.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 2
2
Class 4 Over 500 mW visible radiation
• note that Class 4 also covers pulsed lasers and invisible radiation. Reference should be made to the MPE limits contained in the British Standard in order to verify classification.
These lasers are very powerful and may also be a fire hazard.
Exposure of the skin to the beam may cause injury. Even diffuse reflections are hazardous. Very stringent control measures are required.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 2
3
Engineering controls Engineering controls remove the dependence to follow
rigorous procedures and the possibility of failure of personal protective equipment.
Engineering controls all the safety features built into the design of the laser and its associated equipment.
Examples of Engineering Controls include:• key control;• remote interlock;• beam enclosures;• protective filter installations.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 2
4
Administrative controls Administrative and Procedural Controls are intended to
supplement Engineering Controls to ensure that laser personnel are fully protected from laser hazards.
Administrative/Procedural Controls include:• information, instruction and training;• signage;• protocols• arrangements for maintenance;• arrangements for servicing.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 2
5
SignageClass 1
CLASS 1 LASER PRODUCT
Class 2 LASER RADIATIONDO NOT STARE INTO BEAMCLASS 2 LASER PRODUCT
Class 2M LASER RADIATIONDO NOT STARE INTO BEAM OR VIEW
DIRECTLY WITH OPTICAL INSTRUMENTSCLASS 2M LASER PRODUCT
Class 3B LASER RADIATIONAVOID EXPOSURE TO BEAMCLASS 3B LASER PRODUCT
Class 4 LASER RADIATIONAVOID EYE OR SKIN EXPOSURE TODIRECT OR SCATTERED RADIATION
CLASS 4 LASER PRODUCT
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 2
6
Personal Protective Equipment Personal protective equipment should only be used
when the above measures do not provide sufficient control.
Personal protective equipment includes:• protective eyewear; and• protective clothing.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 2
7
Laser eye protection Selection of eyewear should
be based on:• wavelength(s) being used• radiant exposure;• maximum permissible exposure
(MPE);• optical density of eyewear;• visible light transmission
requirements;• adequate peripheral vision;
prescription lenses; and,• comfort.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 2
8
College Procedures The College’s High Power Laser Safety Policy requires
all work with Class 3B and Class 4 lasers to be subject to protocols approved by Heads of Department and to comply with British Standard BS EN 60825.
There is a supporting Code of Practice which describes the College’s requirements for:• preparation and approval of protocols;• registration of Designated Areas, users and equipment; and,• the need for the lowest class of laser to be used.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 2
9
Protocols Protocols should be developed and implemented before
any use of Class 3B and Class 4 lasers. Protocols should describe:
• the use of the laser;• the Designated Area being used• the laser(s) being used;• the training and competence of the user(s)• the use of personal protective equipment;• any departure from standard conditions.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 3
0
Designated Areas Areas where Class 3B and
Class 4 lasers are used must be registered with the College Safety Unit.
A sign must be affixed near to the entrance of each Designated Area and contain the details of the person responsible for the area, emergency contacts and the name of the Departmental Laser Safety Officer.
DESIGNATED AREACLASS 4 LASER HAZARDNO ENTRY WHEN WARNING LIGHT IS ON
Departmental Laser Safety Officer:
Emergency contact numbers:1)
2)
PERMIT-TO-WORK REQUIRED
Person Responsible for this area:
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 3
1
Laser equipment registration All lasers must be registered
with the Departmental Laser Safety Officer and the College Laser Safety Officer.
The form includes a checklist of the precautions required for each class of laser.
IMPERIAL COLLEGE OF SCIENCE, TECHNOLOGY & MEDICINE
REGISTRATION OF LASER EQUIPMENT
All lasers, except Class 1, must be registered with the Departmental Laser Supervisor and the College Laser Safety Officer.
Supervisor - it is your responsibility to complete this form, keep a copy for your records and return copies to:
(1) Safety Director, 14 Prince' s Gardens (2) Departmental Laser Supervisor (3) Technician Head of Section.
Supervisor Name (Block Capitals): ________________________________________________________________ Phone No: ________________________________
Laser Details (tick or complete entries, as appropriate):
Department: Laser identification number (issued by the Department):
Precise Location (building, room number, location):
Equipment Make: Model: Specification:
Class 2 up to 1mW continuous (visible) Visible or UV or IR
Class 3A up to 5mW continuous (visible) and 25Wm-2 Portable or Fixed
Class 3B* up to 5mW (visible) Continuous or Pulsed
Class 3B** up to 500mW Name of key holder - Classes 3B**, 4 and 1E
Class 4 above 500mW
Class 1E fully enclosed
Brief description of work:
The table below indicates the precautions required for each class of laser and is taken from CVCP Notes of Guidance Part 2:1 Lasers (1992). It will be used by the DepartmentalLaser Supervisor to monitor laser safety. An unshaded block denotes that action is required.
Precautions Class 2 Class 3A Class 3B* Class 3B** Class 4 Class 1 (E)
Remote Interlock
Key Control
Emission Indicator
Beam Shutter
Beam Stop
Beam Level
Beam Enclosure
Eye Protection
Protective Clothing
Eye Examinations
Training
Laser Labels
Door Signs
Signature of Supervisor: _______________________________________________________________________________ Date: ____/____/_____
Signature of Departmental Laser Supervisor: _____________________________________________________________ Date: ____/____/_____
May 94
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 3
2
Laser user registration All laser users must be
authorised and must be registered with the College Laser Safety Officer.
Before a user is registered they should have had an eye test and attended the “Introduction to Laser Safety” course.
IMPERIAL COLLEGE OF SCIENCE, TECHNOLOGY AND MEDICINE
REGISTRATION OF LASER USER
All laser users must be authorised by the Head of Department or the Departmental Laser Supervisor.
Supervisor - it is your responsibility to ensure completion of this form, keep a copy for your records and return copies to:
(1) Safety Director, 14 Prince' s Gardens (2) Departmental Laser Supervisor (3) Technician Head of Section.
Name of Laser User (Block Capitals): _________________________________________ Phone No: ____________________
Department: ______________________________________________________________________________________________
Supervisor Name (Block Capitals): ________________________________________________________________Phone No: ________________________________
User is (please circle): A. Undergraduate C. Research Assistant E. Academic
B. Postgraduate D. Technician
Details of laser(s) User is authorised to use:
Laser Number Class and Type Laser Number Class and Type
To be completed by the User
Have you attended the College Laser Safety Officer' s lecture on laser safety (see Note 2 below)? YES / NO
If "No", have you spoken to the Departmental Laser Supervisor about laser safety? YES / NO
Have you had an eye test - Users of Class 3B** and Class 4 lasers only (see Note 3 below)? YES / NO
Have you read the College Laser Safety Policy and Code of Practice (see Note 4 below)? YES / NO
Notes:
1. Specify Laser Identification Number (issued by the Department), Class and Type (e.g. He - Ne).
2. All new laser users should attend the lecture given by the College Laser Safety Officer. This takes place annually inNovember. If you wish to start using a laser before that date, or miss the lecture, then you must talk to the DepartmentalLaser Supervisor about laser safety training before starting work with lasers.
3. All users of lasers classified as 3B** or 4 must have an eye test before starting work with the lasers and on itscompletion. Long term users should have an eye test every three years. Eye tests must be carried out by an AppointedOptician arranged through the College Health Centre.
4. Copies of the Policy and Code of Practice have been sent to all supervisors of laser work.
Signature of User: ___________________________________________________________________ Date: ____/____/____
Signature of Supervisor: ______________________________________________________________ Date: ____/____/____
Signature of Departmental Laser Supervisor: ____________________________________________ Date: ____/____/____
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 3
3
Eye test Current arrangements at the College
require all users of Class 3B and Class 4 lasers to have a “laser eye test” before starting work with lasers.
A medical examination by a qualified specialist should be carried out immediately after an apparent or suspected injurious ocular exposure.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 3
4
College Laser Safety Officer The College Laser Safety Officer monitors departmental
arrangements and assists departments by:• providing expert advice;• reviewing protocols• maintaining central registers of Designated Areas, users and
laser equipment;• providing training; and,• investigating accidents.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 3
5
Accident Reporting Procedures All incidents or accidents involving the use of lasers must
be reported to the Safety Unit as soon as possible. Any individual who may have been exposed to damaging
laser radiation must be referred for assessment of any damage, preferably within 24 hours of the incident.
Certain accidents may be reportable to the Health and Safety Executive, including:• an accident involving a student which results in them being
taken to hospital for treatment;• an accident which causes a “specified major injury”, which
includes temporary or permanent loss of sight.
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 3
6
Legislation There is no specific legislation in the UK regarding the
use of lasers. However, the following regulations do have to be
complied with:• Management of Health and Safety at Work Regulations 1999• Provision and Use of Work Equipment Regulations 1998• Personal Protective Equipment Regulations 1992• Control of Substances Hazardous to Health Regulations 2002• Electricity at Work Regulations 1989• Reporting of Injuries, Diseases and Dangerous Occurrences
Regulations 1995• Health and Safety (Safety Signs and Signals) Regulations 1996
Impe
rial C
olle
ge S
afet
y U
nit
- In
trod
uctio
n to
lase
r sa
fety
- 3
7
Further training and supervision
Please remember this course has only been an “Introduction to Laser Safety”.
Further information, instruction, training and supervision needs to be given by your supervisor.