immediate loading implant systemtechnical reasons hc2 2.9 mmd is not available with expanded apical...

TP

GH

C2 • Secure anit-rotation through high-precision internal hexagon

• Apical expanded bone thread with No-Itis® surface

• Excellent stability in all bone qualities: double condensation

• Universal application for fixed and removable prosthodontics

• Surface blasted, etched and anodised

• Abutment alignment and 100% tightness by the taper

IMMEDIATE LOADING IMPLANT SYSTEM TPG®

TWO PART IMPLANT SYSTEM HC2

2

HC2 IMPLANTS AND PROSTHETIC COMPONENTS

1. Ask your laboratory to prepare a drill template with the determined bore-

holes for the pilot drills. To be on the safe side, you can ask the laboratory

to insert guide sleeves (REF BFH) into the boreholes, which specify the

exact drill direction. Please use a 2.0 / 2.2 mm Ø drill for the pilot drilling.

2. For the following drill sequences you can use drill stops, which

can be attached and tightened to the drill according to the length of drill-

ing channel. Mucous membrane thickness and template height are taken

into account as needed. Thanks to the extremely high cutting efficiency of

our drills, no ascending drilling sequences will usually be required. Recom-

mended RPM: 2000-5000. Apply sufficient cooling and allow the cooling

to reach the working blades of the drills.

Contra-angle handpiece 2.0 /mm Ø

Drillstop

Holes with guide sleeve

Template

Muscosa

Jaw bone

(Example)

PRELIMINIARY WORK FOR TEMPLATE APPLICATION

DFN 2.9 13 DFN 2.9 15

DS 2

(Pilot drill)

(DFN 3.4 ) / DFN 3.7 DFN 4.2-4.5 (C-Drill 4.2 - 4.5)

(Corticalis drill)

DS 2

(Pilot drill)

DFN 3.0 (DFN 3.4) (C-Drill 3.7)

(Corticalis drill)

1.1 Drill for contra-angle handpiece

Typical sequence of the drills:

Step drill

Bone

Bone

Boneor

The use of DHC is done without previous pilot drill.

Max. torque during insertion of HC 2.9: 35 Ncm.

DS 2

(Pilot drill)

DFN 3.7 DFN 5.5 (C-Drill 5.5)

(Corticalis drill)

Bone

DS 2

(Pilot drill)

DS 2.8

(Pilot drill)

Bone

(hard bone: DFN/DFLN 3.4)

Max. torque during insertion of HC 3.3: 40 Ncm.

General note - HC2 implants are used as compression screws. In order to acchieve a good bone condensation and implant stability, the drilling should be carried out thin-

ner than the core diameter of the implant. The minimal diameter of the drill depends on the bone density. It is therefore not possible to advise drill-sequences which fit all

bone-qualities. Typically in the soft maxillary bone only small drill-diameters are used (e.g. the usage of DOS1 only, for HC2 implants with 3.3 - 5.5 mm diameter), whereas in

the highly mineralized lower jaw a specific drill sequence with respect to the mineralisation of the bone is necessary. For insertion under pressure use the handgrip. Due to

technical reasons HC2 2.9 mmd is not available with expanded apical thread.

HC2 2.9

(head diameter 3.2 mm)

HC2 3.7

HC2 3.3

HC2 5.5 mm

HC2 5.5 mm, 6+2

HC2 4.5 mm

HC2 4.5 mm 6+2

3

1. SURGERY

1.2 Implant packaging

1. Open the lid. The implant is connected

to the lid with a break joint.

2. Remove the implant without touching

the inner walls of the tube.

Original packaging Open packaging using the flap

Remove the label and stick

it intoyour patient’s file.

1.7

Result: a correctly inserted

implant

HC2 implant

Jaw

1.4

After you have attached the insertion

tool, firmly hold the lid in your hand and break

the implant off the top along the break joint.

1.3

Attach the insertion tool to the implant by hol-

ding the top, to which the implant is secured,

with your other hand.

Alternative: Firmly attach the assembled con-

tra-angle handpiece instrument IT 2.5 M to the

implant. For ratchets ITL 2.5 can be used as well.

1.5

Using the ratchet screw the implant clockwise

into the cavity.

The enossal part of the implant must be com-

pletely covered by the bone.

After insertion the implant can be turned by a

1/4 rotation backwards in order to relieve the

bone and allow blood access to the implant site.

TW 2

Jaw

1.6

Disengage the insertion tool

from the implant.

Jaw

TW2

IT 1 or IT 2

Make sure that the

hexagon is in the correct

position

HC2 Implant

Break joint

Lid with

implant mount

Break jointjoint

Lid

1.8

Close the implant with the

suitable cover screw

HT 1.25

CSTI

HC2 implant

Jaw

1.9

After healing period:

Remove cover screw

HT 1.25

CSTI

HC2 implant

Jaw

4

Impression tray

Impression post HLT

HC2 implant

Jaw

Hex-instrument HT 1.25

Thightening of the

impression post HLT

HC2 implant

Jaw

Arrow: Top view.

Direction of rotation:

clockwise.

1.10

Usage of the handgrip and HC2

adapter

1.11

Break off the holder

1.12

Insertion of the implant with axial pressure while turning

IT HC

2.1 PICK-UP IMPRESSIONS

2.1.1 Impression taking using the pick up method

Impression taking using an individual impression tray

2.1.2 Prior to the impression

Impression taking with an A-silicone such as Safeprint by

Dr. Ihde Dental. The use of open and closed impression

tray is possible.

The impression post HLT must not necessarily be unscre-

wed from the implant in order to remove the impression

tray. It can be repositioned later as well.

1. SURGERY AND PICK-UP IMPRESSIONS

Handgrip

5

2.1.3 Take impression

Disengage HLT from the implant: HLT remains in the im-

pression

After the impression is taken, the implant is closed with a

healing abutment (Gingiva former - straight or anatomic)

and the impression is sent to the laboratory.

2.2.1 Impression taking with a closed impression tray

Impression taking using an individual impression tray

2.2.2 Prior to the impression

Impression taking with an A silicone such as Safeprint® IM

by Dr. Ihde Dental.

When applying the closed-tray method, the impression

post TS/TSL HC is not located in the impression tray after

the impression is removed, but in the implant.

2.2.3 Remove impression

When the closed-tray method is applied, the impression

post TS/TSL HC remains on the implant after the impres-

sion tray is removed.

After removal of the impression tray the impression post

will be unscrewed and repositioned in the impression.

After the impression is taken, the implant is closed with a

healing abutment (Gingiva former - straight or anatomic)

and the impression is sent to the laboratory.

Loosen screws with HT 1.25

Window in impression tray

HLT

HC2 implant

Jaw

Tighten the impression post

manualy with the top screw

TS/TSL HC

HC2 implant

Jaw

Arrow: Top view.


clockwise.

Impression post

TS/TSL HC

HC2 implant

Jaw

TS/TSL HC

HC2 implant

Jaw

2.2 CLOSED TRAY IMPRESSION TAKING

2.2 CLOSED TRAY IMPRESSION TAKING

6

3. PROCEDURES IN THE LABORATORY

3.1 Preparation of the impression tray for the

model generation

Pick up method:

Screw analog or M-analog against the impression

post.

3.2 Closed-tray method:

Screw analog IA or M-analog IA HC M to the transfer

post TS HC. �

Subsequently the impression post is repositioned in

the impression. �

The impression can now be casted. In M analogs (IA

HC M) block the lower access to the lock screw out prior

to casting.

3.3

The impression is poured. Then the impression

posts (HLT or TS/TSL HC) are unscrewed from the

laboratory analog.

3.4

The laboratory analog is now in the proper position

and orientation in the gipsum.

3.5

Positioning of the screwable abutments

TLA15 HC, thereby the optimal position and

adequate angulation must be determined.

NOTE The hexagon must be completely inserted

into the analog.

Fasten the laboratory

analog in the impression

using HT 1.25

HLT

IA or M-analog

Tighten the impression post onto

the laboratory analog using the

knurled screw

TS HC

IA or IA HC M

�

�

Gipsum

HT 1.25

screw eindrehen

TLA 15Achten Sie auf die korrekte

Stellung des Hexagons

IA or IA HC M

Gipsum

IA or IA HC M

Laboratory analog

Pour gipsum in

Arrow: Top view.


clockwise.

Arrow: Top view.


counterclockwise.

Arrow: Top view.


clockwise.

7

The problem:

Implants, which are inserted with directional

divergences, cause the technician increased

difficulties

Advantages at a glance:

3. PROCEDURES IN THE LABORATORY

TLA 15 HC

Pattern Resin

Bone

3.6

Ensure proper position of the abutment when

transferring into the mouth.

Tightening torque of the screw during fastening on

the implant: 20 Ncm

3.7

If more than one angled abutment is used, your

laboratory will prepare a detachable synthetic bar (e.g.

from Pattern Resin) in order to facilitate the correct

positioning in the mouth.

TLA 15 HC

Bone

Access to

safety screw

Gingival region

Retention area

Jacket

Safety

screw

APPLICATION IA HC M ANALOGUE

Please note:

For HC2 implants with internal dual-hex (12 corners, HC2) the implant analogs IA 12 (REF 418177) or IA12 M (REF 418178) are

used.

The solution:

IA HC M tapered analog with jacket and TS HC or TSL HC impression

post (right)

The lock screw is firmly tightened against the analog using the hexagon wrench HT

1.77. Thereby the jacket is affixed. Now the M analog can be secured in the impres-

sion. Depending on the implant type this is done by attaching or tightening of the

M analog.

M analogs for HC2: Code: IA HC M

Pack with 1 analog, 1 lock screw and 5 sleeves (REF 418115)

• each M analog can be removed from the model at any time.

• no saw-cut model is necessary any more

• the 8 degree cone angle compensates for angulations between the implants

• all M analogs are equipped with rotation protection.

• damaged analogs can be easily replaced on the same model.

• adjustments can be made directly on the analog. The analog can be easily removed

from the model

• disturbing analogs can be temporarily removed

• these analogs do not need to be “deflasked” from previous models. Leave the jacket,

use the analogs right again

• the analogs can be reused. You save money

8

The surface is sandblasted and acid etched (high temperature), the apical thread has a No-Itis® surface. HC2 implants feature an internal 6-edge, an internal

marginal taper and a US standard internal thread.

NEW HC2 implant is now available with aggressive apical

thread and No-Itis® surface

As a result of many years of clinical observation of products, Dr. Ihde Dental AG has revised the design of the

famous HC2 implant: the broadened apical thread is fully self-cutting and carries the yellow No-Itis® surface.

Thanks to the new thread portion, the implant is more stable even in weak bone and high insertion torque

can be reached.

If the implant is anchored in the 2nd cortical, it may be used in immediate load protocols.

Especially in the upper jaw the usage of the new handgrip (REF311431, with Adapter IT HC REF418196, see

page 15) for inserting the implant is advisable. This tool allows to apply vertical insertion forces and will en-

hance the anchorage.

The drill sequence remains unchanged compared to the former design of the HC2 implant. And of course all

abutments and tools remain the same also if the new implant is applied.

IMPLANTS

Dimensions HC2 4.5 + 13

a) thread Ø basal 4.3 mm

b) hight of the wide thread part

c) micro thread length 2.5 mm

d) nominal Ø 3.7 mm

HEXACONE® IMPLANTS

Description enossal Ø enossal length Code REF Price cat.

HC2 2.9 13 2.9 mm 13 mm HC2 2.9 13 13-413200 G

HC2 2.9 15 2.9 mm 15 mm HC2 2.9 15 13-413201 G

HC2 3.3 8 3.3 mm 8 mm HC2 3.3 8 13-413220 G

HC2 3.3 10 3.3 mm 10 mm HC2 3.3 10 13-413221 G

HC2 3.3 11.5 3.3 mm 11.5 mm HC2 3.3 11.5 13-413222 G

HC2 3.3 13 3.3 mm 13 mm HC2 3.3 13 13-413223 G

HC2 3.3 15 3.3 mm 15 mm HC2 3.3 15 13-413224 G

HC2 3.7 8 3.7 mm 8 mm HC2 3.7 8 13-413202 G

HC2 3.7 10 3.7 mm 10 mm HC2 3.7 10 13-413203 G

HC2 3.7 11.5 3.7 mm 11.5 mm HC2 3.7 11.5 13-413210 G

HC2 3.7 13 3.7 mm 13 mm HC2 3.7 13 13-413204 G

HC2 3.7 15 3.7 mm 15 mm HC2 3.7 15 13-413205 G

HC2 4.5 8 4.5 mm 8 mm HC2 4.5 8 13-413206 G

HC2 4.5 10 4.5 mm 10 mm HC2 4.5 10 13-413207 G

HC2 4.5 11.5 4.5 mm 11.5 mm HC2 4.5 11.5 13-413208 G

HC2 4.5 13 4.5 mm 13 mm HC2 4.5 13 13-413209 G

HC2 5.5 8 5.5 mm 8 mm HC2 5.5 8 13-413211 G

HC2 5.5 10 5.5 mm 10 mm HC2 5.5 10 13-413212 G

HC2 5.5 11.5 5.5 mm 11.5 mm HC2 5.5 11.5 13-413213 G

HC2 5.5 13 5.5 mm 13 mm HC2 5.5 13 13-413214 G

HC2 2.9, 3.3, 4.5 and 5.5 implants will be converted from Dualhex to Hex.

HC2 2.9 must only be used in the load reduced area and not as single tooth implant.

c

b

a

d

9

IMPLANTS AND SURGICAL ACCESSORIES

HC2 6+2 was developed specially for the area of the 1st and 2nd molars in the upper and lower jaw. It is possible and recommendable to use it as a com-

pression screw implant in the upper jaw. Enossal length 6 mm. The upper edge of the polished 75° reverse cone can end at bone level or slightly above

it. The surface is sandblasted and acid etched in a high-temperature process.

Application limitations: HC2 2.9 mm implants may not be placed in a heavily loaded area, especially not in the molar area. Likewise these implants may

not be used where diagonal loading occurs, i.e. not for upper anteriors. Under no circumstances may HC2 2.9 mm implants be used for work that involves

unsupported occlusal surfaces (consoles). If used in immediate load protocols, the prosthetic construction must be inserted on the 2nd postoperative

day, and it should not be removed within the first 6 months.

SURGICAL ACCESSORIES

Each implant is supplied with this surgical screw (CSTI - REF 418101).

HEXACONE® 6+2 IMPLANTS

Description enossal Ø enossal length Code REF Price cat.

HC2 4.5 6+2 4.5 mm 6-8 mm HC2 4.5 6+2 13-413217 G

HC2 5.5 6+2 5.5 mm 6-8 mm HC2 5.5 6+2 13-413218 G

HC2 4.5 6+2 and 5.5 6+2 implants will be converted from Dualhex to Hex.

HC2 6+2 can be countersinked in the bone.

75 ° conus

b

a

c

a) enossal Ø: 4.5 - 5.5 mm

b) enossal length: 6 - 8 mm

c) reverse conus: 2 mm

4.6 mm 4.6 mm

6 mm 6 mm

Description Code REF Price cat.

Gingivaformer

for 3 mm

mucous membrane heightHSI 3 13-418111 B

for 5 mm

mucous membrane heightHSI 5 13-418112 B

Wide

gingivaformer

for 3 mm

mucous membrane heightHSIW 3 13-418191 B

for 5 mm

mucous membrane heightHSIW 5 13-418192 B

Anatomic

gingivaformer

3 mm hight, 4.5 mm widthHSI 3-4.5

13-418268 B

3 mm hight, 5.5 mm widthHSI 3-5.5

13-418269 B

5 mm hight, 6.7 mm width HSI 5-6.7 13-418270 B

Gingivaformer 3 mm hight, 3.3 mm width HSIS 3-3.3 13-418277 B

Gingivaformer MU for HC MU GF MU 13-418302 B

No-Itis® The innovative implant surface

Implants with the new No-Itis®-surface are double-sandblasted and then etched under heat. As final step an electro-chemical staining will be applied

and this last step of the surface preparation smoothens small wells (up to around 5 Micrometers) in the surface. Smooth implants (e.g. systems BCS, BOI)

receive the final surface treatment without any prior sandblasting or etching.

This surface, which is new in dental implantology, is extremely clean and keeps bacteria off the the implant. This surface has been proven successful in

traumatology for a long time. The reduction of roughness on the surface helps preventing peri-implantitis.

During the insertion of the implants the smoother surface reduces heat and thereby less torques is necessary and less heat develops. All other parameters

like the drilling sequence etc. remain unchanged.

10

ABUTMENTS FOR CEMENTED PROSTHETICS

HC SET 1

Screw Description Code REF Price cat.

Screwable abutment without anti-rotation protection for cemented

bridges. Trimmable down and abradable is possible. Height above

implant 8.5 mm, screw in with HT 1.25 Hex key.

The impression is made directly on the TCA, with tool TZ HC.

TCA 13-418129 B

Screwable abutment without anti-rotation protection for cemented

bridges. Trimmable down and abradable is possible. Screw in with HT

1.25 Hex key. The impression is made directly on the TCA.

TCA W 13-418173 B

Superstructure with hex and screw, straight, for cemented bridges.

Can be shortened and trimmed.

Height above implant 8.5 mm. Fasten with HT 1.25.

TLA HC 13-418133 D

Abutment narrow to HC 2.9

Fasten with HT 1.25.TLAS 13-418134 D

Abutment TLA HC 2 (GH) TLA HC2 13-418170 D

Abutment TLA HC 4 (GH) TLA HC4 13-418171 D

Abutment TLA W TLA W 13-418193 D

TLA, 15º angled, 1 mm gingival height (GH), including screw TLA 15 HC1 13-418135 F



TLA, 25ºangled, 1 mm gingival height (GH), including screw TLA 25 HC1 13-418139 F



Anatomic Abutment ANAB 13-418276 E

Recommended insertion torque: 20 Ncm

SF 21

SF 21

GH

GH

Impression taking and laboratory accessories

Code/REF TLA HC REF 13-418133 TZ HC REF 13-418179 PA HC REF 13-418181 IA 12 REF 13-418177**

Straight abutment Impression utility Castable cap Implant analogue

with 12-edge

REF 13-418182 for the complete SET

Price category for the SET F


Temporary cap, for TCA W HC, TLA W HC TPB W 13-418194 A

TEMPORARY CAP

** Note: For the HC2-implant with 12-edge, the implant analogue IA12 (REF 13-418177) or IA12 M (REF 13-418178) is used.


Code

REF

TSL HC

13-418110

TS HC

13-418109

HLT

13-418108

HLTC

13-418107

SF HLT long

13-418185

IA HC / IA 12 HC 2

13-418113/13-418177**

IA HC M / IA 12 M HC 2

13-418115/13-418178**

PA HC

13-418181

PA TLA HC

13-418172

Impression

post for HC.

Hight:

15.5 mm

Impression

post

for HC,

Hight:

10.6 mm

Impression

post for TLA,

TLA 15,

TLA 25

Transfer

post. Sui-

table for

6-edge and

12-edge.

Click on.

Pickup-

screw for

418108/HLT

impression

post

418113 = Implant

analogue for Hex

418177 = for Dual Hex

Implant analogue

with 5 sleeves,

intern. Hex

Castable

abutment

for TCA, TLA

Castable

abutment

for TLA

HC2/4

Price cat. C C C C B B C A A

11

ABUTMENTS FOR SCREW-IN PROSTHETICS



CodeREF

TST13-418147

SFL BTT13-418100

PSTR (grey)

13-418124 (pack of 5)

PSTA

13-418123 (pack of 5)

SF13-418151

Transfer post Long screw TCT-analogue

Castable

abutment,

12 mm high, round

inside

Castable

abutment,

12 mm high, edged

inside

Fastening

screw

Price cat. B A B B B B

In this approach the position of the TCT hex is assigned.


Screwable abutments for bridges and bars,

deliverable for mucogingival levels of 3, 4, 5, 6 mm.

Screw in with HT 1.77.

TSA 3 13-418143 B

TSA 4 13-418144 B

TSA 5 13-418145 B

TSA 6 13-418146 B


Screwable mesostructure for bridges and bars,

screw in with HT 1.77 hex key. For mucogingival

levels of 0.5 mm, 1.5 mm and 2.5 mm.

TCT HC 0.5 13-418130 B

TCT HC 1.5 13-418131 B

TCT HC 2.5 13-418132 B



CodeREF

TS13-418142

BTS13-418152

PSS (white) SF13-418151

Impression post TSA-analogue Castable abutment, 10.5 mm high

5 per pack

Fastening screw for

PSS on BTS/TSA

Price cat. B B B B


Code

REF

IA HC / IA 12 HC 2

13-418113 / 13-418177**

HLT

13-418108

PSTR

13-418124 (5 pieces)

Implant analogue for HC2�

IA HC = 6 -edges, IA 12 HC = 12-edges

Transfer post for

HC and HC 2, with Hex.

Alternative: Castable abutment,

round inside 12 mm high

Price cat. B C B

IA HC IA 12 HC


Screw for PSTA SF TCTL 418165 A

Castable abutment,12 mm high, edged inside PSTA 418123 B

Screw-on mesio structure for bridges and bases TCTL 0.5 13-418138 D

TCT Set (TCTL 0.5, PSTA, SF TCTL) 13-418263 F

Hex

TCT-SET

SF TCTL

PSTA

TCTL 0.5

12

ABUTMENTS FOR REMOVABLE PROSTHETICS

CASTABLE ABUTMENTS


Castable abutments with hex, incl. metal basis (Ti6Al4V)

and screw for crown 10 mm high, white (not for casting-on)PLAB 13-418120 B

Castable abutments with hex, incl. metal basis (CoCrMo)

and screw for crown 10 mm high, white (for direct casting-on)PLAB 2 13-418183 G

Castable abutment including screw for bridges

(UCLA technique) 10 mm, red PLA 13-418158 B



ABUTMENTS

Description Material Code REF Price cat.

HEX-reverse-abutment,

incl. screw SF 275 (REF 418275)Ti6Al4V HRA HC 13-418273 D

Tempbase for HRA HC TPB E 13-418274 C

This abutment turns the internal hexagon of the HC2-implant into an external standard-hexagon. The prosthetic screw is

screwed through. It tightens the prosthetic and the abutment at the same time.

Ti6Al4V CoCrMo

SF 275

TPB E

HRA HC


Code HLT HLTC SF HLT long IA HC / IA 12 HC 2

REF 13-418108 13-418107 13-418185 13-418113 / 13-418177**

Transfer post for

HC and HC 2, with Hex.

Transfer post for snap-

ping onto the HC2 im-

plant. Suitable for 6-edge

and 12-edge. Click on.

Pickup-screw for

418108 / HLT

impression post

Implant analogue for

HC2�

IA HC = 6 -edges

IA 12 HC = 12-edges

Preiskat. C C B B

IA HC IA 12 HC


Localicer® for HC2 hight 2 mm LOC HC 2 13-418116 C

Localicer® for HC2 hight 4 mm LOC HC 4 13-418117 C

Adequate tool: HT 1.77. We recommend to use minimally 6 implants per jaw and to use a single denture as splinting.

LOCALICER®

ACCESSORIES FOR LOCALICER®


instrument for mounting and de-mounting Localicer Caps LOC Tool 13-462335 C

Analog + impression cap set AA LOC 13-462337 C

Set with 4 nylon caps + 1 housing NCS 13-462338 D

Set of two, yellow, with increased friction strength R-Cap 13-462336 B

Pull-off force: *black 125 g, red 350 g, blue 500 g, pink 1000 g // *Black cap is for temporary solutions up to one month.

13

ABUTMENTS FOR REMOVABLE PROSTHETICS AND ACCESSORIES

MULTI - UNIT ABUTMENTS

ACCESSORIES FOR MULTI - UNIT ABUTMENTS


Temporary base, Ti6Al4V (SF MU2 has to be ordered separately) TC MU2 13-418290 D

Transfer straight, Ti6Al4V, incl. screw SFL MU2 TS MU2 13-418291 C

Castable for multiunit, incl. screw PA MU2 13-418292 A

Screw for TC MU, Ti6Al4V SF MU2 13-418293 A

Lab analogue for multiunit, Ti6Al4V IA MU2 13-418295 B

Hex-instrument, long HT 1.25 13-425100 C

Hex-instrument, long HT 1.77 13-425103 C

Screw


MU2 17 HC, angled, Ti6Al4V, incl. SF 20 MU2 17 HC 13-418281 L

MU2 35 HC, angled, Ti6Al4V, incl. SF 20 MU2 35 HC 13-418282 L

MU2S 0.5 HC, straight, Ti6Al4V MU2S 0.5 HC 13-418283 G



GF MU2 gingivaformer, Ti6Al4V. Incl. SF MU2 H above abutment shoulder 6 mm 13-418286 C

MU2 localicer, Ti6Al4V. Incl. SF MU2 Hight above abutment shoulder 6.7 mm 13-418287 C

Prosthetic screw for MU2 SF 20 13-420943 A

Insertion of the angled MU2-abutments with HT 1.25 // Insertion of the straight MU2S-abutments with HT 1.77

h = 3 mm

h = 4 mm

6 mm

6.7 mm


Ball abutments for fitting prostheses, head diameter 2.5 mm, for fit-

ting to TSA 3 - 6 abutments, application on TSA 3 - 6 abutmentsSB 13-418153 B

ACCESSORIES


Pu

ll-o

ff f

orc

es

Nylon cap NC Nylon cap R-NC

with increased friction strength

(for usage with worn-out Localicer)

for poly-

merization

directly into

the denture

Code TSA 3 to 6 TS BTS NC NC 1 NC 2 R-NC R-NC 1 R-NC 2 H

REF 13-418143 / -46 13-418142 13-418152 13-465028 13-465029 13-465030 13-465034 13-465033 13-465032 13-465031

Hight above

implant

3-6 mm

Impression post

for TSA and TCA

TSA-

analogue

ca. 1200 g

white

ca. 800 g

pink

ca. 500 g

yellow

green, strong pink,

medium

orange,

soft

Metal sleeve

for

all NC

Price cat. B B B A A A A A A B

Description Hight h Code REF Price cat.

Ball abutment, head - 0 2.5mm

Use with HT 1.25

Use with

NC-caps

0.5 mm TB 0.5 13-418126 B

2.0 mm TB 2 13-418127 B

4.0 mm TB 4 13-418128 B

hh

h


Bur cylinder, rverse, 20°. Incl. screw SF 20 FZ 20 HC 13-418262 D

REVERSE CONE CYLINDER

14

INSTRUMENTS AND TOOLS

Description Type Code REF Price cat.

IT 2.5 Short, 8 mm, click-on, 6-edges IT 2.5 13-418174 B

ITL 2.5 Long, 22 mm, click-on, 6-edges ITL 2.5 13-418175 B

ITM 2.5 Medium, 20 mm, click-on, 6-edges ITM 2.5 13-418176 B

IT 2.5 M Insertion tool for contra-angle handp. IT 2.5 M 13-418150 B

IT 2.5 M 12Insertion tool contra-angle, 12-edges

Insertion torque with max. 40 NcmIT 2.5 M 12 13-418200 B

ITWH 2.5 M Insertion tool contra-angle for HC ITWH 2.5 M 13-418184 C

IT1 12 Insertion tool short,12-edges IT1 12 13-418197 B

IT2 12 Insertion tool long, 12-edges IT2 12 13-418198 B

IT3 12 Insertion tool medium,12-edges IT3 12 13-418199 B

INSERTION TOOLS

Ø working rangeMax. working

depth

Total

lengthColor Code REF Price cat.

0.1 mm - 1.5 mm 15 mm 31.7 mm yellow BCD 1 13-900240 C

0.1 mm - 1.5 mm 15 mm 42 mm yellow BCDX 1 13-900243 C

2.0 mm / 3.6 mm 13 mm 30 mm DFN 2.9 13 13-418102 E

2.0 mm / 3.6 mm 15 mm 32 mm DFN 2.9 15 13-418103 E

2.0 mm 17 mm 36.5 mm DS 2 13-425001 D

2.8 mm 17 mm 36.5 mm DS 2.8 13-425005 D

2.7 mm 18 mm 36 mm DFN 3.0 13-425030 E

3.0 mm 18 mm 36 mm DFN 3.4 13-425031 E

3.4 mm 18 mm 36 mm DFN 3.7 13-425032 E

4.05 mm 18 mm 36 mm DFN 4.2 - 4.5 13-425033 E

4.4 mm 18 mm 36 mm DFN 5.5 13-425034 E

2.7 mm 18 mm 39 mm DFLN 3.0 13-425035 E

3.0 mm 18 mm 39 mm DFLN 3.4 13-425036 E

3.4 mm 18 mm 39 mm DFLN 3.7 13-425037 E

4.05 mm 18 mm 39 mm DFLN 4.2 - 4.5 13-425038 E

3.4 mm 11.5 mm 30 mm DFSN 3.7 13-425039 D

3.9 mm 11.5 mm 30 mm DFSN 4.2 - 4.5 13-425040 D

max. 3.4 mm 5 mm 27 mm C Drill 3.7 13-425043 D

max. 4.05 mm 5 mm 27 mm C Drill 4.2 - 4.5 13-425044 D

max. 5.8 mm 5 mm 27 mm C Drill 5.5 13-425045 D

It has been scientifically proven that HEATLESS® drills generate 55% less heat than traditional bone drills from other

manufacturers. This makes it possible to use higher rotational speeds: between 3,000 and 5,000 rpm are recommended

with good external cooling and intermittent drill technique.

Namely for the implant system HC2

HEATLESS® - DRILL DFN / DFLN FOR IMPLANTS WITH CONICAL CORE

TITAN BASE

Description Type Material Code REF Price cat.

Titan base

incl. screwAbutment basefor zirkonium Ti6Al4V MB HC 13-418267 D

Titan base

incl. screwTi6Al4V MBR HC 13-418272 D

Base for TPB 3 HC

incl. screw SF 20For scanner to HC implants BioPEEK® TPB 3 HC 13-418280 B

15

TOOLS

TOOLS

Description Type Length Code REF Price cat.

Hex-Tool 1.25 long 21 mm HT 1.25 13-425100 C

Torx-Tool 1.25 long 21 mm TT 1.25 13-425105 C

Hex-Tool for contra-angle, extra-long 45 mm HTW 1.25 13-425111 B

Hex-Tool 1.25 kurz 14 mm HTS 1.25 13-425101 C

Hex-Tool 1.77 for all suprastructures 19 mm HT 1.77 13-425103 C

Hex-Tool 1.25 M for contra-angle, long 26.1 mm HT 1.25 M 13-425112 B

Hex-Tool 1.77 M for contra-angle, long 28.6 mm HT 1.77 M 13-425113 B

Hex-Tool, extra-long 45 mm HTX 1.25 13-425102 C

Hex-Tool for contra-angle, extra-long 45 mm HTX 1.77 13-425104 C

Punch, 4.9 mm 0 for contra-angle PUW 1 13-425404 C

Punch, 3.9 mm 0 for contra-angle PUW 2 13-425405 C

Punch, 5.2 mm 0 manual PU 13-425406 C

standardized

probe

Scale 1 mm for X-ray

measurements22 mm PDG 13-425400 A

DX2Drill extension contra angle

handpiece, extends by 19 mmDX2 13-500704 D

DX2 H

Drill extention contra angle handpiece, extends

by 19 mm, W&H-hexagon on shank and in front

section

DX2 H 13-500708 D

Guide sleeveTitanium, for pilot drill,

5 pieces / unit10 mm BFH 13-425401 A

X-ray measuring

sphere

Surgical steel

5 pieces / unit, 0.5 mm 0RM 13-425403 A

Adapter for handgrip Adapter IT HC 13-418196 C

Handgrip, self-locking ** 13-311431 V

Handgrip for adapter, screwable 13-311430 V

Adapter for all contra angle handpiece

instruments, compatible to handle110 mm 13-310530 C

Ratchet For all Hex-instruments and applicators RAT 2 13-425051 K

RatchetAngled, for all Hex-instruments and

applicatorsRAT 3 13-425052 S

TW 2 * Torque Wrench (heavy duty), 10 - 70 Ncm TW 2 13-425402 S

UAW***

Universal ratchet adapter for all contra angle

handpiece instruments, for TW2

and RAT2. Max. 30 Ncm

UAW 13-425107 E

* It is recommended to have the torque ratchets recalibrated by us once a year.

** for cleaning this instrument an ultrasonic cleaning device and a thermo-desinfector (i.e. Miele TD-series) are required. If these devices

are not available in the dental office the handle with REF311430 should be purchased instead.

*** Do not use UAW in combination with RAT2 with Heatless® bone drills. The maximum insertion torque for UAW and Heatless® bone drills

is 35 Ncm. UAW may therefore be used only with TW2.

TOOLS

HANDGRIP-TRAY (empty)

REF 13-60043

EUR 69,90

Size of closed tray: B = 90 mm / L = 195 mm / H = 45 mm

For safe storage and sterilisation

of handgrips (max. 3 pieces) and

adapters (max. 8 pieces). Plastic,

autoclavable up to 134°C, not sui-

table for dry heat sterilizers.

16HC216

Autoclavable up to 134 °C, not suitable for dry heat sterilizers

This surgical kit contains all drills and tools for first works with the HC2 system.

Material: autoclavable plastic

Description Code REF Price €

Insertion tool IT 2.5 13-418174

Insertion tool ITL 2.5 13-418175

Insertion tool

for contra angle handpieceIT 2.5M 13-418150

Hex-instrument, long HT 1.25 13-425100

Spiraldrill DS 2 13-425001

Formdrill DFN 3.0 13-425030



Formdrill DFN 4.2 - 4.5 13-425033

Corticalis drill 3.7 C Drill 3.7 13-425043

Torque wrench TW2 13-425402

Starter-Tray for HC2 (with content)* 13-S60021-K 678,80

* tray without content upon request

Cortic

rqu

art

y w

Cor

Tor

Sta

* tray

HC2 STARTER - TRAY

17TP

GGGIMMEDIATE LOADING IMPLANT SYSTEM TPG®

18

enossal

length

1.8 mm

4.8 mm

Implant with Strauman® compatible

internal cone connection.

TPG® implants provide a sharp and cutting crestal thread, which

engages in to the corticals of the extraction sockets. The apical

compression thread provides perfect stability both in com-

pressed spongious and in cortical bone. TPG® implants may

be used both in extraction sockets and in healed bone areals.

TPG® implants are used for circular bridges and segments with

at least 3 implants. Under adequate loading conditions and if

enough implants are splinted, the treatment will be performed

in an immediate load protocol. Due to their polished surface

with No-Itis®-protection, TPG® implants are extremely resistant

agains bacterial colonialization and peri-implantitis.

TPG® implants may be inserted into fresh

extraction sockets with lateral and bi-corti-

cal engagement.

View from top: TPG® implants may be in-

serted into fresh extraction. The voids in the

extraction sockes may receive augmentati-

on or fill with woven bone.

TPG® implant engaged in the distal maxilla

and the pterygoid plate of the shenoid

bone. In this indication this implant may be

used for circular bridges and segments with

at least 3 implants.

TPG® IMPLANTS

EXAMPLES FOR THE USE OF TPG® IMPLANTS

Description enossal Ø enossal length H above bone Surface Material REF Pricecat.

TPG 4.1 8 4.8 mm 8 mm 1.8 mm Polished, No-Itis® Ti6Al4V 13-420106 H








Minimal differences to the displayed No-Itis® implant-colour has no influence on the quality of the surface.

All TPG® implants are being delivered incl. OF5 STI (REF 13-420426)

TPG 4.1 8

TPG 4.1 10

19

Description Neck Code REF Price cat.

Plattform offset abutment. Tool: IT K (REF 462320) * 1.5 mm OF 4 STI 13-420424 * E

Plattform offset abutment, large head. 1.3 mm OF 5 STI 13-420426 E

Plattform offset abutment, large head. 15° bendable. 4 mm OF 5L STI 13-420427 E

Insertion tool, length 20 mm. Tool: RAT, RAT2, TW2 IT K 13-462320 C

Insertion tool for large head IT2 BCS 13-900030 E

* Laboratory accessories can be found in the Simpladent KOC® BECES® system application (REF13-0003-09)

Description Code REF Pricecat.

Straight, screw-in abutment with pre-assembled screw for

cemented crowns or bridges. Fasten with TT 1.25.TLA STI 13-425110 D

15°angled, screw-in abutment with pre-assembled screw for

cemented crowns or bridges. Fasten with TT 1.25. TLA 15 STI 13-425111 E

20°angled, screw-in abutment with pre-assembled

screw for cemented crowns or bridges. Fasten with TT 1.25.TLA 20 STI 13-425112 E

25°angled, screw-in abutment with pre-assembled

screw for cemented crowns or bridges. Fasten with TT 1.25. TLA 25 STI 13-425113 E

One-piece abutment with solid thread, for cemented crowns or bridges,

height above implant 6.5 mm, 8°incline. Can be shortened or trimmed.

Flat on one side. Direct impression or transfer to lab

analogue IA STI. Fasten with HT 1.25.

TCA STI 13-420313 D

Single-piece and anti-rotational octagonal screw-in abutment;

for crowns, bridges and bar connectors. Height above implant: 1.5 mm.

Fasten with HT 1.77 / HTX 1.77

OSA STI 13-420338 D

CoCrMo bar coping for all S implants with SF 350 or SF 365,

height above implant: 5.5 mm. Screw directly onto implant.SKC STI 13-420366 E

With conus (without anti-rotation)


Castable abutment incl. SF 215 replacement screw, 10.5 mm high.

For ULCA. Fasten with HT 1.25.PA STI 13-420358 C

Use with impression post TSX STI (REF13-420411) and analogue IA STI (REF13-420347)

TPG® ABUTMENTS

ABUTMENTS FOR CEMENTED PROSTHETICS

ABUTMENTS FOR SCREW-IN PROSTHETICS

PLATTFORM OFFSET ABUTMENTS

External

octagon

20

TPG® DRILLS AND TOOLS


Adapter TPG, Engages in the internal tri-lobe inside the conus. Adapter TPG 13-425106 D

Adapter short, for large head AA5 15° 13-462052 C

Adapter short, for large head AA5 25° 13-462053 C

Handgrip, not dismountable. Cleaning in ultrasonic bath at 45°,

with alkaline cleansing medium. For adapters, self-locking.Handgrip 13-311431 V

Handgrip, dismountable, can be cleaned manually.

For adapters, can be disassembled.Handgrip 13-311430 V

* must be used with max. 60 Ncm only. If the bone is harder, IT1-3 TPG has to be used with RAT 2 or TW2.

AA5 15°

AA5 25°

°

255°

Surgical steel, color coded, depth coded and autoclavable. The drill is marked with laser depth markings.

HEATLESS® DRILLS «DOS» FOR TPG® IMPLANTS

TOOLS FOR MANUAL INSERTION


Insertion tool, short 12 mm IT1 TPG 13-425116 C

Insertion tool, medium 16 mm IT2 TPG 13-425117 C

Insertion tool, long 20 mm IT3 TPG 13-425118 C

Insertion tool for contra-angle, 30 mm ITM TPG 13-425119 B

Ratchet, for all Hex-instruments and insertion tools 13-RAT 2 K

Description max. working length Code REF Price cat.

BCD 1 15 mm 13-900240 C

BCDX 1 15 mm 13-900243 C

DOS 2, black 17 mm DOS 2 13-455312 D

DOS 4, blue 21 mm DOS 4 13-455314 D

DOS 5, green 17 mm DOS 5 13-455315 D

Twist Drill 2.0 / 21, Ø 2.0 mm 21 mm 13-90022 D

Countersink head, for implant-Ø 4.1 mm DRA 4.1 CS 13-425047 D

D

INSERTION TOOLS FOR RATCHET

21TPG21

TPG® ACCESSORIES


Lab analogue, with cone IA STI 13-420347 B

Transfer post, engages on the outer cone, 9 mm high

Tighten with HT 1.25TS STI 13-420345 B

Transfer post, engages on the outer cone, 13 mm high

Tighten with HT 1.25TSX STI 13-420411 B

Hex-instrument. Length 21 mm, Ø 1.25 mm HT 1.25 13-HT 1.25 C

Hex-instrument extralong. Length 45 mm, Ø 1.25 mm HTX 1.25 13-425102 C

Torx-instrument. Length 21 mm, Ø 1.25 mm TT 1.25 13-TT 1.25 C

Synthetic base castable, 7.4 mm high. For TLA STI and TCA STI PS 13-420354 A

Synthetic base castable, 4 mm high. For TLA15 STI PS 15 13-420355 A



IMPRESSION AND LABORATORY ACCESSORIES

22

TPG® SMALL TRAY

Description Code REF Price € / cat.

Insertion tool IT2 BECES 13-900030

Insertion tool IT K 13-462320

Hex instrument, long HT 1.25 13-425100

Pathfinder drill BCD 1 13-900240

Pathfinder drill BCDX 1 13-900243

Heatless drill for implants with conical core DOS 2 13-455312



Countersink heads DRA 4.1 CS 13-425047

Standardized probe PDG 13-425400

Twist drill Twist Drill 2.0 / 21 13-90022

Insertion tool, short 12 mm IT1 TPG 13-425116

Insertion tool, medium 16 mm IT2 TPG 13-425117

Insertion tool, long 20 mm IT3 TPG 13-425118

Insertion tool for contra-angle, 30 mm ITM TPG 13-425119

Ratchet for all Hex-instruments and insertion tools RAT 2 13-425051

Small tray with content 13-S60047-K 729,90

Small tray empty 13-60047-K 149,90

optional Adapter TPG 13-425106 D

optional Handgrip for adapters, self-locking 13-311431 V

23

IMPLANT SURFACE AND MATERIAL

NO-ITIS® - THE INNOVATIVE IMPLANT SURFACE

Implants with the new No-Itis®-surface are double-sandblasted and then etched ander heat. As final step

an electro-chemical staining will be applied and this last step of the surface preparation smoothens small

wells (up to aroand 5 Micrometers) in the surface. Smooth implants (e.g. systems BECES®, COI) receive the

final surface treatment without any prior sandblasting or etching. This surface, which is new in dental

implantology, is extremely clean and keeps bacteria off the the implant. This surface has been proven

successful in traumatology for a long time. The reduction of roughness on the surface helps preventing

peri-implantitis. During the insertion of the implants the smoother surface reduces heat and thereby less

torques is necessary and less heat develops. All other parameters like the drilling sequence etc. remain

unchanged.

Ti6AL4V ELI

Ti6AL4V ELI also called „Grade 5“, is a purified version of the conventional 6/4 Ti-Alloy. It is used for more

than 50% of all human metallic implants. The material features superb mechanical and chemical pro-

perties, and it is very resistent against corrosion. Also regarding biocompatibility and the support of cell-

growth this specific titanium-alloy shows advantages compared to pure titanium. For these reasons the

material is used so widespread. Ti6AL4V ELI provides a 25% higher stability compared to pure titanium.

0029REF 13-0005-09_TPG-HC2_SAP_EN_V001_05/15

Simpladent GmbH Phone +41 (0)55 293 23 70

Dorfplatz 11 [email protected]

CH - 8737 Gommiswald / SG www.simpladent-implants.com

PLEASE CHECK THE VALID PRICE LIST OF YOUR LOCAL COORDINATOR

Symbols on the packs

Production

No.

Sterilized by

gamma radiation

Sterilization

Ethylene oxide

Single-

use

product

Instruction

for use

Expiry date Store

in a dry

place

Temperature

range from

-5 °C to 35 °C

Store tightly

keep closed

Do not use if

packing is

damaged

Do not

resterilize

Manu-

facturer

-5 °C

35 °C

Rx ONLYNon-

sterile

Intended for use by

dentists or surgeons

only

Production

date

We are certified DIN EN ISO 13485, and annex II of EEC Directive 93/42 EWG (2007).

Due to technical reasons the product dimensions shown in this brochure might deviate from reality. HC2 and TPG® are registered trademarks.

HC2 implants are patent-protected.

In case that implants would be reprocessed (cleaned, resterilized) infections could occur, because no validated procedures for reprocessing are available.

dent GmbH

tz 11

37 Gommiswa

CHECK THE VA

hone +41 (0)55 2

SG w

Sim

Do

CH

PLE

23 70

ent.ch

s.com

ATOR

immediate loading implant systemtechnical reasons hc2 2.9 mmd is not available with expanded apical...

Documents