igt bartop game conversion kit - welcome to jcm...
TRANSCRIPT
IGT Bartop Game C 2008
Par
tallation Guide
e Conversion Kit BV Installation converting an IGT Bartop Game Validator. The kit contains the necessary l Validator housing onto the four (4) rovided within the individual Bartop
T Bartop Game Conversion Kit contains bly hardware kits: ponents that can be used for both the . In addition, each kit contains parts that nding the age and style of the game.
– 1 - Drill Template (Part No: 200-101005R1)
– 1 - Adaptor Plate (Part No: 200-101006R1)
• 1 - Minor Hardware Parts Kit containing: – 6 - M3 Kep-lock Nuts (Part No. 140-
021033R) – 6 - 4-40 Kep-lock Nuts (Part No. 490-
001768R) – 1- M4x8 Pan Head Screw (Part No.
490-001108R) – 4 - M3x8 Counter-sink Screw (Part No.
173-300008R) – 3 - 6-32 Nuts (Part No. 490-001811R) – 3 - M3 Washer (Part No. 490-
PERSONAL NWrite any pertihere. allation Guide
onversion Kit Installation Guide April, 2008 April,
Ins
IGT Bartop GamFor WBA/UBA
This document contains information forConsole to accept a WBA or UBA Bill hardware to mount a WBA or UBA Bilexisting Bill Validator mounting studs pGame Machine being modified. The IGthe following equipment and sub-assem
NOTE: The parts kits contain comUBA and WBA Bill Validator Unitsmay or may not be needed, depe
• 1 - Installation Guide (Part No: 960-000154R)
• 1 - Gold Bartop Game Conversion Kit (Part No. 701-100035R)
• 1 - Chrome Bartop Game Conversion Kit (Part No. 701-100036R)
• 1 - Brushed Satin Bartop Game Conversion Kit (Part No. 701-100037R)
• 1 - Hammered Graytone Bartop Game Conversion Kit (Part No. 701-100038R)
• 1 - Cover Parts Kit containing: – 1 - Gold Bar Top Cover (Part No: 200-
200279R) – 1 - Chrome Bar Top Cover (Part No:
200-200280R)
OTES AND COMMENT AREAnent notes or comments regarding your particular installation Inst
o. 960-000154R_Rev. 1 © 2008, JCM American, Corporation1
– 1 - Brushed Satin Bar Top Cover (Part No: 200-200281R)
– 1 - Regular Bar Top Cover (Part No: 200-200282R)
Major Hardware Parts Kit containing: – 1 - WBA Entry Bezel (Part No: 900-
100452R) – 1 - WBA Plaque (Part No: 900-
101120RA) – 1 - Yellow LED PCB (Part No: 300-
100282R) – 1 - Enclosure Housing (Part No: 200-
100748R) – 1 - Cash Box Guide (Part No: 200-
200273R) – 1 - Stop Bracket (Part No: 200-
200274R) – 1 - Barrier (Part No: 200-200276R) – 1 - Light Box Cover (Part No: 200-
200277R) – 1 - BA Plaque Mount (Part No: 200-
200278R)
001813R) – 3 - M4 Washer (Part No. 192-
400001R) – 2 - M3x8 Pan Head Screw (Part No.
186-300508R) – 2 - M4X6 Screws (186-300107RA) – 1 - M4x10 Pan Head Screw (Part No.
181-400010R)
Tool Requirements – 4 - 1/8" Twist Drill Bits – 1 - Variable Speed Drill – 1 - Machine Cutting Oil – 1 - Phillips Screwdriver (Small and
Large Tip) – 1 - Flat Head Screwdriver (Small and
Large Tip) – 1 - Wire Cutters – 1 - Pliers or Vice Grips – 1 - Metal File (Large and Small Rip) – 1 - Hack Saw & Blades
© 2008, JCM American, Corporation Part N8t No. 960-000154R_Rev. 1
925 Pilot Road, Las Vegas, Nevada 89119Office & Technical Support: (800) 683-7248 (option 5 after hours), FAX: (702) 651-0214
E-mail: [email protected] http://www.jcm-american.com
JCM is a registered trademark of JCM American Corporation. All other product names mentioned herein may be registered trademarks or trademarks of their respective companies. Furthermore, ™, ® and © are not always mentioned in each case throughout this publication.
• 1 -
P © 2008, JCM American, Corporation7
IG tion Guide April, 2008
PF
or UBA) into the Bar Top DBV Cover
nto the Bar Top Cover above the Window k Nuts provided in the kit (See Figure 20 ).
onitor to the game. the new bezel properly aligns with the stalled. omplete.
Figure 19 Drilling Template Holes
Drill Six 1/8Inch HolesAt TemplateHoles
Bezel Template
BV Bezel Installed
Six 4-40Kep-LockNuts
SecureWithSix 4-40Kep-LockNuts
SecureWith
art No. 960-000154R_Rev. 1 2
Typical UBA
Standard Hammered Graytone Validator Cover
Typical 701-100171R Parts Kit Contents
Typical Cover Parts Kit Contents (1 of 4)
Figure 1 Primary IGT Bartop Conversion Kit Component Parts
20. Reinstall and reconnect the video m21. Close the Bar Top Cover and ensure
associated UBA/WBA Unit when inInstallation of JCM equipment is now c
Figure 20 New D
T Bartop Game Conversion Kit Installation Guide Installa
RIMARY IGT BARTOP CONVERSION KIT COMPONENTSigure 1 illustrates the primary components of an IGT Bartop Conversion Kit.
Major Boxed Parts Kit Packages
Minor Parts Kit PackageTypical WBA
18. Mount the appreciate Bezel (WBA Window (See Figure 20 ).
19. Mount the new DBV Bezel Cover oHole using the six (6) 4-40 Kep-Loc
Figure 18 Removing Old BV Bezel
Remove ExistingBV Bezel
New DBVBezel inWindow
New DBVBezel inWindow
IG ion Guide April, 2008
Pa © 2008, JCM American, Corporation3
Figure 17 Removing Old BV Cover Figure 16 Mounting WBA/UBA Frame
EDUREoceed as follows: Game being converted.ve the original Bill Validator from the
igure 3).
ousing frame from the enclosure ed original BV frame.n remove the original enclosure from the nting hardware from original enclosure.
ed from the game, remove the Door Switch ure 6), including the three nuts that hold the e 7).
Figure 3 Existing BV Removed
Existing Bill ValidatorRemoved
Figure 5 Removing Enclosure
Remove ExistingEnclosure
rt No. 960-000154R_Rev. 1 6
16. Remove the original Bill Validator Window Bezel Plate from the Bar Top Table Game and discard it (See Figure 18).
17. Place the Drill Template onto the rectangular Bill Validator Window opening, and drill six (6) 1/8 inch holes in the Bar Top Cover at the template drill hole locations (See Figure 19).NOTE: Drilling through the Bar Top can be difficult. Set the drill to a low speed (600-700 RPM) and cool the drill bit with machine oil while drilling.
6. Once the original enclosure is removHousing from its back side (See FigCash Box Cover in place (See Figur
Figure 4 Removing BV Frame
Existing Bill ValidatorFrame
T Bartop Game Conversion Kit Installation Guide Installat
15. Remove the retaining bar that holds the original Bill Validator Window Cover in place (See Figure 17).
Figure 15 Installing Stop Bracket
Stop Bracket
Kit SuppliedM4x6 Screws
Figure 14 Installing Cash Box Guide
Cash BoxGuideM4x10Screw
Cash BoxGuideM4x10Screw
Remove
Bill ValidatorWindow Cover
Existing
Discard Cover
New WBAor UBAFrame
Mount with4 - M4x8Nuts
IGT BARTOP CONVERSION PROCTo begin the IGT Bartop Conversion pr
1. Remove power from the IGT Bartop2. Open the game’s top cover and remo
cabinet housing (See Figure 2 and F
3. Discard the removed Bill Validator.4. Remove the original Bill Validator h
(See Figure 4) and discard the remov5. Temporarily remove the monitor, the
game (See Figure 5). Retain all mou
Figure 2 Removing Existing BV
Existing Bill Validator
Game FrameEnclosure
P
IG April, 2008
g to the Switch Bracket Assembly (See Fig-
re into the game using the three kit supplied ware retained during Step 7 (See Figure 13).
Figure 11 Later Version Switch Bracket Assembly
New BillValidatorEnclosure
FlangeRemoved
ounted in Step 9 has been purposely w hardware placement.
Kit Supplied New Bill ValidatorEnclosure
6-32 MountingNuts
T Bartop Game Conversion Kit Installation Guide
7. Discard the original enclosure, but retain the Cash Box Cover and all of the mounting hardware removed during this process.
8. Install the Adaptor Plate (See Figure 8 ) onto the side of the game using the two kit supplied M3 screws with washers and one kit supplied M4 screw with washer. Place the two M3 screws into positions A and B (See Figure 8 ), and put the M4 screw into position C (See Figure 8 ).
Figure 7 Removing Cover Nuts
Remove &Retain the3 Nuts
Cash Box Cover
Existing Enclosure
Figure 6 Removing Switch Housing
Remove Door SwitchHousing
Existing Enclosure
Attach With3 RetainedNuts
Adaptor Plate
10. Reconnect the Switch Connector Pluure 12 ).
11. Install the newly assembled enclosu(3) 6-32 Nuts and the mounting hard
Figure 10 Early Version Switch Bracket Assembly
Old BillValidatorEnclosure
Cut OffFlangeHere
NOTE: The Cash Box Door mremoved in Figure 13 to sho
Reconnect Door SwitchPlug
Reconnect Door SwitchPlug
© 2008, JCM American, Corporation5
New Original
ure 14 ) into the newly installed enclosure ead Screw (See Figure 14 ).R) onto the DBV frame using the two (2)
See Figure 14).e Figure 17 ) into the newly installed ounter Sink Screws provided with the kit
Figure 13 Installing New Enclosure
Cash Box Cover Mounts(Door Removed)
art No. 960-000154R_Rev. 1 4
9. Remount the Cash Box Door (See Figure 9) and Switch Bracket Assembly (See Figure 12 ) removed in Step 7 onto the new Bill Validator Enclosure.
Re-use the mounting hardware retained during Step 7 to re-attach the Cash Box Door and Switch Bracket Assembly.
Figure 9 Remounting Cash Box Door
Bill ValidatorEnclosure
Cash BoxCover
Figure 8 Attaching Adaptor Plate
NOTE: An early and later version of the new Bill Validator Enclosure exists (See Figure 10 & Figure 11). If the early version is in your kit, the flange containing a Spring Loaded Pin must first be removed as indicated at the Red circled area in Figure 11.
12. Install the Cash Box Guide (See Figusing the kit supplied M4x10 Pan H
13. Install the Stop Bracket (200-200274M4x6 screws supplied with the kit (
14. Install the UBA or WBA Frame (Seenclosure using the four (4) M3x8 C(See Figure 17 ).
Figure 12 Remounting the Switch Bracket Assembly
Re-Attach Door SwitchHousing