ibox-whiskey lake/ryzen user manualdownload.asrock.com/ipc/manual/ibox-8365ue.pdf · ibox-whiskey...

iBOX-Whiskey Lake/Ryzen

User Manual

Version 1.0Published November 2019

Version 1.0 Published November 2019 Copyright©2019 ASRock Inc. All rights reserved.

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this documentation may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:

Specifications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance.“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock’s Website: www.ASRock.com

Replaceable batteries

CAUTIONRISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

Contact Information

If you need to contact ASRock or want to know more about ASRock, you’re welcome to visit ASRock’s website at www.ASRock.com; or you may contact your dealer for further information.

ASRock Incorporation6F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District,

Taipei City 112, Taiwan (R.O.C.)

The terms HDMI® and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Product Specifications 2

1.3 Block Diagram 4

Chapter 2 Product Overview 6

2.1 Front View 6

2.2 Rear View 7

2.3 Inside View 8

Chapter 3 Hardware Installation 9

3.1 How to Remove the Bottom Case 9

3.2 How to Install the WiFi Module 10

3.3 How to Install the M.2 SSD 11

3.4 How to Install the 2.5-inch Hard Drive 12

3.5 How to Install the Memory Modules (DDR4 Low Voltage (1.2V)) 14

Chapter 4 Motherboard 15

4.1.1 Motherboard Layout (IBOX-Whiskey Lake Series) 15

4.1.2 Motherboard Specifications 16

4.1.3 Jumpers Setup 18

4.1.4 Onboard Headers and Connectors 19

4.2.1 Motherboard Layout (IBOX-Ryzen Series) 22

4.2.2 Motherboard Specifications 23

4.2.3 Jumpers Setup 25

4.2.4 Onboard Headers and Connectors 26

4.3 Expansion Slots (M.2 Slots) 29

Chapter 5 Troubleshooting 30


PB 1

Engl

ish

Chapter 1 Introduction

1.1 Package Contents• iBOX-Whiskey Lake/Ryzen• NUC-8365UE/NUC-8665UE (pre-installed motherboard)• 1 x SATA 1 to 1 Power Cable• 4 x HDD Screws (M3x4)• 1 x WiFi Module Screw • 1 x Screw for M.2 slot• 1 x 96W Power Adapter• User Manual

Because the hardware specifications might be updated, the content of this documentation will be subject to change without notice.

If any items are missing or appear damaged, contact your authorized dealer.


PB 2

Engl

ish

1.2 Product Specifications


Barebone

CPU

Intel® 8th Gen (Whiskey lake-U) Core™ MCP ProcessorsI3-8145UE DC, 2.2GHz, 15 W (IBOX-8145UE) I5-8365UE QC 1.6GHz, 15 W (IBOX-8365UE) I7-8665UE QC 1.7GHz, 15 W (IBOX-8665UE)

AMD Ryzen™ Embedded R-SeriesR1505G, DC, 2.4GHz, 12-25W (IBOX-R1000V)R1606G, DC, 2.6GHz, 12-25W (IBOX-R1000M)

AMD Ryzen™ Embedded V-SeriesV1605B, QC, 2GHz, 12-25W (IBOX-V1000M)

OS N/A

Chipset Intel® I3-8145UE DC/I5-8365UE QC/I7-8665UE QC SoC AMD Ryzen™ R1505G DC/R1606G DC/V1605B QC SoC

Memory Supports Dual Channel DDR4 2400 MHz, 2 x SO-DIMM slots, Max. 32GB

HDD

N/A

Optional

Supports 1 x 2.5" SATA HDD*

LAN Gigabit LAN

WiFi Optional

Audio Realtek ALC233

eMMC

M.2 slot

2.5”HDD

3 4

English

* For iBOX-Whiskey Lake/Ryzen, it is not recommended to install 2.5” HDD. If you install the 2.5” HDD, please keep the iBOX-Whiskey Lake/Ryzen in a vertical position to ensure better cooling performance.

Front I/O 2 x USB 3.0 (Type A), 1 x HDMI, 2 x DP, 2 x LAN, DC-IN, 1 x Kensington lock

Rear I/O 1 x COM Port, 2 x USB 2.0 (Type A), 1 x USB 3.0 (Type A), 1 x Audio-out with MIC-In

Power Unit 96W Adapter

Dimension 171.8mm (W) x 150mm (D) x 71.5mm (H)

VESA Bracket included , supports 75 x 75 and 100 x 100 mm

Volume (Liters)

0.6L

Operating Temperature

0°C~50°C


3 4

Engl

ish

1.3 Block Diagram55

44

33

22

11

DD

CC

BB

AA

Gb LAN

RJ45

DIS

PL

AY

1DDI1

Gb LAN

RJ45

LA

N2 +

US

B3.0

HDMI 1.4b

DP 2

DP 1

RTL8111G

PAGE:28

480Mbp/s

PCIe 8

5Gb/s

SPI

LPC1

3.3V LPC

FA

NX

11x CPU FAN(4-pin)

12V only

Serial Port * 1

- Internal Header *1(RS-232/422/485)

5Gb/s

SP

I FL

AS

H3

.3V

/12

8M

b

NUC-8365U

E

Au

dio

EDP

Co

mb

o D

P+

HD

MI

Headset

(combo jack)

eD

P T

O H

DM

I

CHRONTEL CH7525A-BF

M.2

M-K

EY

slot

(224

2/2

260/2

28

0 b

y b

rack

et)

HDA/I2S

DDI2

DD

R4

SO

-DIM

M 2

40

0DDR4 - CH1

M.2

E-K

EY

(223

0)

PCIe 9

USB2.0

LA

N1

+ U

SB

3.0

1 F

ro

nt U

SB

3.0

po

rt T

yp

e A

1 P

OR

T

SATA Port 0

Gen3 x1 port

SATA Port 1

Gen3 x1 port

NUC Form Factor

Inte

rn

al U

SB

2.0

Hea

der

2 P

OR

T

C.S ALC233-VB2 MQFN-48

REALTEK/COPPER MATERIAL

I219LM

NCT5567D(C)

SPI TPM SLB9670VQ2.0

TP

M

PCIe*1+USB

WH

L-U

LT

RA

Inte

l

SP

I

SA

TA

3_

1

PAGE:36

PAGE:27

PAGE:20,21

SIO

128-bit Dual-Channel Memory x 2 Slots

DD

R4

SO

-DIM

M 2

40

0DDR4 - CH0

PCIe 7

5Gb/s

PAGE:20,21

PAGE:29

PAGE:22

PAGE:25

PAGE:25

PAGE:29

PAGE:35

PAGE:15

PAGE:23

PAGE:24

PAGE:31

PAGE:33

PAGE:33

PAGE:26

PCIe 13,14,15,16

PCIe*4/SATA

5 6

English

5 5

4 4

3 3

2 2

1 1

DD

CC

BB

AA

SIO

Nuvoton NCT6627UD

DDR4 SO-DIMM 2400MT/S (W/ECC)

Dual Channel

AM

DR

yzen

R10

00/V

1000

UA

RT

*1

DP++ Connector

DP3

DP1

LPC

Hea

der

LPC BUS

HW Monitor

FANx1

4X4-R1000/V1000

DDR4 SO-DIMM 2400MT/S (W/ECC)

DP++ Connector

DP0

HDMI2.0 Con

TiSN75DP159RSBR

Retimer

USB 3.1 G2 port 1/2

USB

3.1

G2

con

(Rea

r I/

O)

BIO

SSPI

Rea

ltek

ALC

233

Line

_Out

Mic

_In

com

bo ja

ckHD AUDIO

PCIE#4

RTL

8111

G

PCIE#5

RTL

8111

G

Gb LAN

RJ45

Gb LAN

RJ45

Switc

hGFX#0

SATA#0

SATA

3_1

M.2 M Key

2242/2260

SATA/PCIe

PCIE#0

M.2

E K

eyUSB 2.0 port 0/5

USB

2.0

con

. (in

tern

al)

COM port (RS232/422/485)

PCIE#1

HUB1 port 2

USB 3.1 G2 port 3

USB

3.1

G2

con

(Fro

nt I/

O)

GFX[1:3]


5 6

Engl

ish

Chapter 2 Product OverviewThis chapter provides diagrams showing the location of important components of the iBOX-Whiskey Lake/Ryzen.

2.1 Front View

No. Description

1 Antenna Port2 Power Button3 DC Jack (DC IN)4 HDMI Port5 2 x USB 3.0 Ports (Type A)6 HDD LED7 Power LED8 2 x Display Ports9 2 x RJ-45 Ports10 Kensington Lock Slot

1 2 3 4 5

6 7 8 9 10

7 8

English

2.2 Rear View

No. Description

1 COM Port2 2 x USB 2.0 Ports (Type A)3 USB3.0 Port (Type A)4 Audio(Mic-in, Line-out)

* There are two LEDs on the LAN port. Please refer to the table below for the LAN port LED indications.

Activity / Link LED Speed LED

Status Description Status DescriptionOff No Link Off 10Mbps connectionBlinking Data Activity Orange 100Mbps connectionOn Link Green 1Gbps connection

ACT/LINK LED

SPEED LED

LAN Port

1 2

3 4


7 8

Engl

ish

2.3 Inside View

No. Description

1 Mini PCIe Slot2 M.2 Slot 3 SATA 3.0 Connectors4 SO-DIMM Slot5 Hard disk drive tray (compatible with 2.5" SATA HDD)

SO-DIMM memory, hard drive and mSATA SSD are not included with this system.

4

32

1 5


PB 9

Engl

ish

Chapter 3 Hardware InstallationThis chapter helps you install or remove important components.

3.1 How to Remove the Bottom Case1. Remove the four screws on the bottom case.2. Then lift up and remove the bottom panel..

2

1

10 11

English

3.2 How to Install the WiFi Module1. Locate the WiFi Module slot on the motherboard.

2. Carefully insert the WiFi Module into the slot.

3. Tighten the screw to secure the WiFi Module to the motherboard.


10 11

Engl

ish

3.3 How to Install the M.2 SSD1. Locate the M.2 slot on the motherboard.

2. Carefully insert the M.2 SSD into the slot.

3. Tighten the screw to secure the M.2 SSD to the motherboard.

12 13

English

3.4 How to Install the 2.5-inch Hard Drive1. Remove the four screws on the bottom case. Then lift up and remove the bottom panel.

2. Attach the HDD cage to the bottom panel and secure it using the four screws. Then connect the SATA cable to the HDD.


12 13

Engl

ish

3. Connect the SATA Data and Power Cable to the motherboard.

4. Then reinstall the bottom panel.

14 15

English

3.5 How to Install the Memory Modules (DDR4 Low Voltage (1.2V))

1. Carefully insert the SO-DIMM memory modules into the slot at a 30-degree angle.

2. Push down until the modules snap into place.

1. The iBOX-Whiskey Lake/Ryzen requires DDR4 SO-DIMM (1.2V).2. For dual channel configuration, you always need to install identical (the same brand,

speed, size and chip-type) DDR4 SO-DIMM pairs.

The SO-DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.


14 15

Engl

ish

Chapter 4 Motherboard 4.1.1 Motherboard Layout (IBOX-Whiskey Lake Series)

M2

_2

AUDIO1

HD

MI1

USB 3.1:USB3_3

DC_IN1

M.2

SS

D(M

2_

1)

DP

2

DIS

PL

AY

1

SATA3_1

DDR4_B1 (Support DDR4L Only)

DDR4_A1 (Support DDR4L Only)

SATA_PWR1

1

NUC-8365U

Industrial

LA

N1

US

B3

.1:

US

B3

_1

LA

N2

US

B3

.1:

US

B3

_2

BIOSROM

M2_SEL2

1

CLRMOS1

1

1

LP

C1

RESET HDLED

PWRBTN PLED

PANEL1

1

PW

R_

JP

1

1

USB2_3_4

1

COM1

1

1 : M.2 Key-M Socket (M2_1)2 : M.2 Key-E Socket (M2_2)3 : USB2.0 Connector (USB2_3_4)4 : COM Port Header (RS232/422/485)5 : System Panel Header (PANEL1)6 : LPC Debug Header (LPC1)7 : ATX/AT Mode Jumper (PWR_JP1)8 : SATA Power Output Connector (SATA_PWR1)9 : SATA3 Connector (SATA3_1) 10 : M.2 Select (M2_SEL1)11 : Clear CMOS Headers (CLRMOS1)

Back Side :Power Button (PWR_BTN1)Fan Connector (FAN1)

16 17

English

4.1.2 Motherboard Specifications

Form Factor Dimensions NUC 4.09" x 4.02" (104 x 102mm)

Processor System

CPU

Intel® 8th Gen (Whiskey lake-U) Core™ MCP Processors I3-8145UE DC, 2.2GHz, 15 W (NUC-8145UE) I5-8365UE QC 1.6GHz, 15 W (NUC-8365UE) I7-8665UE QC 1.7GHz, 15 W (NUC-8665UE)

AMD Ryzen™ Embedded R-SeriesR1505G, DC, 2.4GHz, 12-25W (4X4-R1000V)R1606G, DC, 2.6GHz, 12-25W (4X4-R1000M)

AMD Ryzen™ Embedded V-SeriesV1605B, QC, 2GHz, 12-25W (4X4-V1000M)

Chipset SoC

Expansion Slot

PCIe N/AMini-PCIe N/AmSATA N/A

M.2

1 x Key M (2242/2260/2280 by BRACKET) with PCIe x4 and SATA3 for SSD1 x Key E (2230) with PCIe x1 and USB 2.0 for Wireless

MemoryTechnology Dual Channel DDR4 2400 MHzMax. 32GBSocket 2 x SO-DIMM

Graphics

Controller N/ADVI N/ALVDS N/A

HDMIHDMI 1 : Supports max resolution up to 4Kx2K@30Hz

DisplayPortSupports max resolution up to 3840 x 2160@60Hz

Multi Display Triple DisplayeDP N/A

Ethernet Ethernet 10/100/1000 MbpsController 1 x Intel® I219LM, 1 x Realtek RTL8111G)


16 17

Engl

ish

Internal Connector

USB 2 x USB 2.0LVDS/inverter

N/A

eDP N/AVGA N/ASerial 1 x COM (RS-232/422/485)SATA 1 x SATA3 ( 6.0Gb/s)Parallel N/AGPIO N/ASATA PWR Output

1

Speaker Header

N/A

TPM N/AWatchdog Timer

Output N/AInterval N/A

Power Requirements

Input PWR 12V / 96W DC-In (DC Jack)

Power OnATX SupportedATX: Press Button to PWR on after Power input ready

Environment

Operating Temp

0ºC – 60ºC

Storage Temp

-40ºC – 85°C

Rear I/O

VGA N/ADVI N/AHDMI 1DisplayPort 2Ethernet 2USB 3 x USB 3.1Audio 1 (Mic-in, Line-out)Serial N/AeSATA N/APS2 N/A

18 19

English

4.1.3 Jumpers SetupThe illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins.

Clear CMOS Jumper (3-pin CLRMOS1)

(see p.15, No. 11)

Note: CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug

the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, user default profile and MAC address will be cleared only if the CMOS battery is removed.

Clear CMOSDefault

ATX/AT Mode Jumper 1-2: AT Mode(3-pin PWR_JP1) 2-3: ATX Mode(see p.15, No. 7)

M.2 Select Open: M.2(2-pin M2_SEL1) Short: SATA3_1(see p.15, No. 10)

1


18 19

Engl

ish

4.1.4 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!

SATA Power Output Connector Please connect a SATA (SATA_PWR1) power cable to this connector.(see p.15, No. 8)

SATA3 Connector This Serial ATA3 (SATA3) (SATA3_1: see p.15, No. 9) connector supports SATA data cables for internal storage devices. The current SATA3 interface allows up to 6.0 Gb/s data transfer rate.

USB 2.0 Connector There is one USB 2.0 (9-pin USB2_3_4) connector on this (see p.15, No. 3) motherboard.

DUMMY

GND GND

+B

-B

+A

-A

USB_PWR USB_PWR

1

_ DUMMY

1

System Panel Header This header accommodates(9-pin PANEL1) several system front panel (see p.15, No. 5) functions.

Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

PWRBTN (Power Switch): Connect to the power switch on the chassis front panel. You may configure

the way to turn off your system using the power switch.

GN

DR

ES

ET

#

PW

RB

TN

#

PL

ED

-

PL

ED

+

GN

D

HD

LE

D-

HD

LE

D+

1

GN

D

20 21

English

LPC Debug Header This connector supports a (13-pin LPC1) Trusted Platform Module (TPM) (see p.15, No. 6) system, which can securely store keys, digital certificates, passwords, and data. A TPM system also helps enhance network security, protects digital identities, and ensures platform integrity.

RESET (Reset Switch): Connect to the reset switch on the chassis front panel. Press the reset

switch to restart the computer if the computer freezes and fails to perform a normal restart.

PLED (System Power LED): Connect to the power status indicator on the chassis front panel. The LED

is on when the system is operating. The LED keeps blinking when the sys-tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).

HDLED (Hard Drive Activity LED): Connect to the hard drive activity LED on the chassis front panel. The LED

is on when the hard drive is reading or writing data.

The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assign-ments are matched correctly.

PCIRST#

FRAME

PCICLK

* This motherboard supports RS232/422/485 on COM1 port. Please refer to below table for the pin definition. In addition, COM1 port (RS232/422/485) can be adjusted in BIOS setup utility > Advanced Screen > Super IO Configuration.

PIN RS232 RS422 RS4851 DCD, Data Carrier Detect TX- RTX-2 RXD, Receive Data TX+ RTX+3 TXD, Transmit Data RX+ N/A4 DTR, Data Terminal Ready RX- N/A5 GND GND GND6 DSR, Data Set Ready N/A N/A7 RTS, Request To Send N/A N/A8 CTS, Clear To Send N/A N/A9 N/A N/A N/A

COM1 Port Pin Definition

COM Port Header (RS232/422/485) (9-pin COM1: see p.15, No. 4)


20 21

Engl

ish

Back Side:Power Button Header(PWR_BTN1)

Fan Connector(FAN1)

1

FAN_SPEED_CONTROL

FAN_SPEED

+12VGND

22 23

English

4.2.1 Motherboard Layout (IBOX-Ryzen Series)

M2

E_

1

AUDIO1

HD

MI1

USB 3.1:USB3_3

DC_IN1

M.2

SS

D(M

2M

_1

)

DP

2

DIS

PL

AY

1SATA3_1

DDR4_B1 (Support DDR4 Only)

DDR4_A1 (Support DDR4 Only)

SATA_PWR1

1

Industrial

LA

N1

US

B3

.1:

US

B3

_1

LA

N2

US

B3

.1:

US

B3

_2

BIOSROM

1

LP

C1

1

CL

RC

MO

S1

1

COM1

1

USB2_0_5

1

HDLED RESET

PLED PWRBTN

PANEL1

1 : M.2 Key-M Socket (M2M_1)2 : M.2 Key-E Socket (M2E_1)3 : COM Port Header (RS232/422/485)4 : System Panel Header (PANEL1)5 : USB2.0 Connector (USB2_0_5)6 : LPC Debug Header (LPC1)7 : Clear CMOS Headers (CLRCMOS1) 8 : SATA Power Output Connector (SATA_PWR1)9 : SATA3 Connector (SATA3_1)

Back Side :Power Button (PWR_BTN3)Fan Connector (FAN1)


22 23

Engl

ish

4.2.2 Motherboard Specifications

Form Factor Dimensions NUC 4.09" x 4.02" (104 x 102mm)

Processor System

CPU

AMD Ryzen™ Embedded R-Series(R1606G, DC, 2.6GHz, 12-25W) (4X4-R1000M)(R1505G, DC, 2.4GHz, 12-25W) (4X4-R1000V)AMD Ryzen™ Embedded V-Series (V1605B, QC, 2GHz, 12-25W) (4X4-V1000M)

Chipset SoC

Expansion Slot M.2

1 x Key M (2242/2260/2280 by BRACKET) with PCIe x4 and SATA3 for SSD1 x Key E (2230) with PCIe x1 and USB 2.0 for Wireless

Memory

Technology Dual Channel DDR4 2400MHzMax. 32GBSocket 2 x SO-DIMMECC Support

Yes

Graphics

ControllerAMD Radeon™ Vega 3 Graphics (4X4-R1000M / 4X4-R1000V)AMD Radeon™ Vega 8 Graphics (4X4-V1000M)

HDMISupports HDMI 2.0, max resolution up to 4096x2160@ 60Hz

DisplayPortDisplayPort 1.4 with max resolution up to 4096 x 2160@ 60Hz

Multi Display Triple Display

Ethernet Ethernet 10/100/1000 MbpsController 2 x Realtek RTL8111G

Front I/O Front USB 1 x USB 3.1Front Audio 1 (Mic-in, Line-out)

Rear I/O

HDMI 1DisplayPort 2Ethernet 2USB 2 x USB 3.1

24 25

English

Internal Connector

USB 2 x USB 2.0Serial 1 x COM (RS-232/422/485)SATA 1 x SATA3 (6.0Gb/s)SATA PWR Output

1

TPM 1 x HeaderWatchdog Timer

Output From Super I/O to drag RESETCON#Interval 256 segments, 0,1,2…255sec

Power Requirements

Input PWR 12V only (DC Jack)

Power On

AT/ATX SupportedAT: Directly PWR on as Power input readyEnvironment ATX: Press Button to PWR on after Power input ready

Environment

Operating Temp

0ºC – 60ºC

Storage Temp

-40ºC – 85°C


24 25

Engl

ish

4.2.3 Jumpers SetupThe illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins.

Clear CMOS Jumper (3-pin CLRMOS1)

(see p.22, No. 7)

Note: CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug

the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, user default profile and MAC address will be cleared only if the CMOS battery is removed.

Clear CMOSDefault

26 27

English

4.2.4 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!

SATA Power Output Connector Please connect a SATA (SATA_PWR1) power cable to this connector.(see p.22, No. 8)

SATA3 Connector This Serial ATA3 (SATA3) (SATA3_1: see p.22, No. 9) connector supports SATA data cables for internal storage devices. The current SATA3 interface allows up to 6.0 Gb/s data transfer rate.

USB 2.0 Connector There is one USB 2.0 (9-pin USB2_0_5) connector on this (see p.22, No. 5) motherboard.

1

System Panel Header This header accommodates(9-pin PANEL1) several system front panel (see p.22, No. 4) functions.

Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

PWRBTN (Power Switch): Connect to the power switch on the chassis front panel. You may configure

the way to turn off your system using the power switch.

DUMMY

GND

RESET#

PWRBTN#PLED-

PLED+

GNDHDLED-

HDLED+

1

GND


26 27

Engl

ish

LPC Debug Header This connector supports a (13-pin LPC1) Trusted Platform Module (TPM) (see p.22, No. 6) system, which can securely store keys, digital certificates, passwords, and data. A TPM system also helps enhance network security, protects digital identities, and ensures platform integrity.

RESET (Reset Switch): Connect to the reset switch on the chassis front panel. Press the reset

switch to restart the computer if the computer freezes and fails to perform a normal restart.

PLED (System Power LED): Connect to the power status indicator on the chassis front panel. The LED

is on when the system is operating. The LED keeps blinking when the sys-tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).

HDLED (Hard Drive Activity LED): Connect to the hard drive activity LED on the chassis front panel. The LED

is on when the hard drive is reading or writing data.

The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assign-ments are matched correctly.

PCIRST#

FRAME

PCICLK

* This motherboard supports RS232/422/485 on COM1 port. Please refer to below table for the pin definition. In addition, COM1 port (RS232/422/485) can be adjusted in BIOS setup utility > Advanced Screen > Super IO Configuration.

COM1 Port Pin Definition

COM Port Header (RS232/422/485) (9-pin COM1: see p.22, No. 3) CCTS#1

RRTS#1

DDSR#1DDTR#1

RRXD1

GNDTTXD1

DDCD#1

1

RRI#1

PIN RS232 RS422 RS4851 DCD, Data Carrier Detect TX- RTX-2 RXD, Receive Data TX+ RTX+3 TXD, Transmit Data RX+ N/A4 DTR, Data Terminal Ready RX- N/A5 GND GND GND6 DSR, Data Set Ready N/A N/A7 RTS, Request To Send N/A N/A8 CTS, Clear To Send N/A N/A9 N/A N/A N/A

28 29

English

Back Side:Power Button Header(PWR_BTN3)

Fan Connector(FAN1)

1

FAN_SPEED_CONTROL

FAN_SPEED

+12VGND


28 29

Engl

ish

4.3 Expansion Slots (M.2 Slots)There are 2 M.2 slots on this motherboard.

M.2 for SSD: Key M (M2_1) (2242/2260/2280 by BRACKET) supports PCIe x4 and SATA3 for SSD.

M.2 for Wi-Fi: Key E (M2_2) (2230) supports PCIe x1 and USB 2.0 for Wireless.

M.2 Key-M Socket (M2_1) M.2 Key-E Socket (M2_2)

30 31

English

Chapter 5 Troubleshooting

A. If you find a loud noise from Audio line out, please click on the playback button to turn it off.


30 31

Engl

ish

B. If there is no sound from your Audio Mic, make sure your select the correct audio device.

1. Click on the Audio Manager shortcut on your desktop.2. Click the Front Panel button.3. Select the device you plug in and click OK to save the settings.

1

2

3

ibox-whiskey lake/ryzen user manualdownload.asrock.com/ipc/manual/ibox-8365ue.pdf · ibox-whiskey...

Documents