hvr-mrc1 - espec

Revision HistoryRevision History

Sony EMCS Co.HVR-MRC1

SERVICE MANUAL

Link

DISASSEMBLY

BLOCK DIAGRAMS

SERVICE NOTE

SPECIFICATIONS

PRINTED WIRING BOARDS

SCHEMATIC DIAGRAMS

FRAME SCHEMATIC DIAGRAM

ADJUSTMENTS

INSTRUCTION MANUAL

REPAIR PARTS LIST

Link

Ver. 1.2 2009.03

2009C0500-1 © 2009.3

Published by Kohda TEC9-852-266-13

US ModelCanadian Model

AEP ModelE Model

Chinese ModelJapanese Model

The components identified bymark 0 or dotted line withmark 0 are critical for safety.Replace only with part num-ber specified.

Les composants identifiés par unemarque 0 sont critiques pour lasécurité.Ne les remplacer que par une pièceportant le numéro spécifié.

MEMORY RECORDING UNIT

HVR-MRC1

Revised-2Replacement of the previously issuedSERVICE MANUAL 9-852-266-12with this manual.

— 2 —HVR-MRC1

ENGLISH JAPANESEENGLISH JAPANESE

SPECIFICATIONS

SystemFile system FAT32CompactFlash 133x 2 GB or more

The capacity is the value when 1GB equals 1 billion bytes.The actual usable capacity maybe slightly less becauseadministrative files etc. areincluded.

File format HDV recording MPEG-2TS(.m2t)

DVCAM/DV recordingAVI-Type1(.AVI)RAW DV (.DV)

Input signalHDV recording/playback

Video: MPEG-2TS1080/60i, 30p, 24p1080/50i, 25p

Audio: 2 CH MPEG 1 AudioLayer2 Stereo (16 bit 48 kHz)(1/2 CH)4 CH MPEG 2 AudioLayer2 Stereo (16 bit 48 kHz)(3/4 CH)

DVCAM/DV recording/playbackVideo: DV embeddedAudio: PCM digital

(12/16 bit, 32k, 48k)Recordable time 2 GB Approx. 9 minutes

4 GB Approx. 18 minutes8 GB Approx. 36 minutes16 GB Approx. 72 minutes

GeneralPower requirement DC 7.2 V (battery pack)

DC 8.4 V (AC adaptor)Power consumption 2.2 WOperating temperature 0 °C to 40 °C (32 °F to 104 °F)Storage temperature –20 °C to +60 °C (–4 °F to +140 °F)Operating humidity 20 % (20 °C) to 90 % (35 °C)

(no condensation)Dimensions

HVR-MRC1 : Approx. 57 × 102 × 34 mm(2 1/4 × 4 × 1 3/8 in.)

HVR-MRC1+HVRA-CR1: Approx. 77 × 106 × 51 mm(3 × 4 1/8 × 2 in.)(including the projecting parts)(w/h/d)

MassHVR-MRC1 : Approx. 130 g (4.5 oz)HVR-MRC1+HVRA-CR1: Approx. 210 g (7.4 oz)

(excluding CompactFlash andbattery pack)

Input/output jack i.LINK(IEEE1394 6-pin connector S400)

Optional accessories AC adaptor/chargerAC-VQ1050BBattery packNP-F570/F770/F970

Design and specifications are subject to change withoutnotice.

— 3 —HVR-MRC1


概略仕様

システムファイルシステム FAT32コンパクトフラッシュ 133x 2 GB以上

容量は、 1 GBを 10億バイトで計算した場合の数値です。

また管理用ファイルなどを含むため、

実際使用できる容量は若干減少する場

合があります。

ファイルフォーマット HDV記録時 MPEG-2TS（ .ｍ 2ｔ） DVCAM/DV記録時

AVI-Type1（ .AVI） RAW DV（ .DV）

対応入力信号

HDV記録再生時ビデオ： MPEG-2TS1080/60i , 30p , 24p1080/50i , 25p

オーディオ： 2CH MPEG1 AudioLayer2 Stereo(16bit 48KHz)(1/2CH)4CH MPEG2 AudioLayer2 Stereo(16bit 48KHz)(3/4CH)

DVCAM/DV記録再生時ビデオ： DV embeddedオーディオ： PCMデジタル

（ 12/16 bit,32k,48k)

録画可能時間 2GB 約 9分 4GB 約 18分 8GB 約 36分 16GB 約 72分

電源部・その他電源電圧バッテリー端子入力 7.2 V

DC端子入力　 8.4 V　消費電力 2.2 W動作温度 0 °C～ 40 °C保存温度 -20 °C～ +60 °C動作湿度 20 ％（ 20 °C）～ 90 ％（ 35 °C）

（結露がないこと）

外形寸法 HVR-MRC1：約 57× 102× 34 ｍｍ HVR-MRC1+HVRA-CR1：約 77× 106× 51 ｍｍ（最大突起部を含む）

（幅／高さ／奥行き）

質量 HVR-MRC1：約 130ｇ HVR-MRC1+HVRA-CR1：約 210ｇ（コンパクトフラッシュ、バッテリー含ま

ず）

入力出力端子 i.LINK(IEEE1394 6ピンコネクター S400）

別売アクセサリー ACアダプター /チャージャー　 AC-VQ1050アクセサリーキット　 ACCKIT-D11Bバッテリーパック　 NP-F570/F770/F970

本機の仕様および外観は、改良のため予告なく変更すること

がありますが、ご了承ください。

— 4 —HVR-MRC1


SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITHMARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTSLIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESECOMPONENTS WITH SONY PARTS WHOSE PART NUMBERSAPPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTSPUBLISHED BY SONY.

1. Check the area of your repair for unsoldered or poorly-solderedconnections. Check the entire board surface for solder splashesand bridges.

2. Check the interboard wiring to ensure that no wires are"pinched" or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularlytransistors, that were installed during a previous repair. Pointthem out to the customer and recommend their replacement.

4. Look for parts which, through functioning, show obvious signsof deterioration. Point them out to the customer andrecommend their replacement.

5. Check the B+ voltage to see it is at the values specified.6. Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270˚Cduring repairing.

• Do not touch the soldering iron on the same conductor of thecircuit board (within 3 times).

• Be careful not to apply force on the conductor when solderingor unsoldering.

Unleaded solderBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed withthe lead free mark due to their particular size.)

: LEAD FREE MARKUnleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40°C higher than

ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350°C.Caution: The printed pattern (copper foil) may peel away if theheated tip is applied for too long, so be careful!

• Strong viscosityUnleaded solder is more viscous (sticky, less prone to flow) thanordinary solder so use caution not to let solder bridges occur suchas on IC pins, etc.

• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

ATTENTION AU COMPOSANT AYANT RAPPORTÀ LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LESDIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONTCRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NEREMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONYDONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OUDANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

— 5 —HVR-MRC1


1. 注意事項をお守りください。サービスのとき特に注意を要する個所については，キャビネット，シャーシ，部品などにラベルや捺印で注意事項を表示しています。これらの注意書き及び取扱説明書等の注意事項を必ずお守り下さい。

2. 指定部品のご使用をセットの部品は難燃性や耐電圧など安全上の特性を持ったものとなっています。従って交換部品は，使用されていたものと同じ特性の部品を使用して下さい。特に回路図，部品表に0印で指定されている安全上重要な部品は必ず指定のものをご使用下さい。

3. 部品の取付けや配線の引きまわしはもとどおりに安全上，チューブやテープなどの絶縁材料を使用したり，プリント基板から浮かして取付けた部品があります。また内部配線は引きまわしやクランパによって発熱部品や高圧部品に接近しないよう配慮されていますので，これらは必ずもとどおりにして下さい。

4. サービス後は安全点検をサービスのために取外したネジ，部品，配線がもとどおりになっているか，またサービスした個所の周辺を劣化させてしまったところがないかなどを点検し，安全性が確保されていることを確認して下さい。

5. チップ部品交換時の注意• 取外した部品は再使用しないで下さい。• タンタルコンデンサのマイナス側は熱に弱いため交換時は注意して下さい。

サービス，点検時には次のことにご注意下さい。

6. フレキシブルプリント基板の取扱いについて• コテ先温度を270前後にして行なって下さい。• 同一パターンに何度もコテ先を当てないで下さい。（3回以内）

• パターンに力が加わらないよう注意して下さい。7. 無鉛半田について無鉛半田を使用している基板には，無鉛（Lead Free）を意味するレッドフリーマークがプリントされています。（注意：基板サイズによっては，無鉛半田を使用して

いてもレッドフリーマークがプリントされていないものがあります）

：レッドフリーマーク無鉛半田には，以下の特性があります。• 融点が従来の半田よりも約40高い。従来の半田こてをそのまま使用することは可能ですが，少し長めにこてを当てる必要があります。温度調節機能のついた半田こてを使用する場合，約350に設定して下さい。注意：半田こてを長く当てすぎると，基板のパター

ン（銅箔）がはがれてしまうことがありますので，注意して下さい。

• 粘性が強い従来の半田よりも粘性が強いため，IC端子などが半田ブリッジしないように注意して下さい。

• 従来の半田と混ぜて使用可能無鉛半田には無鉛半田を追加するのが最適ですが，従来の半田を追加しても構いません。

1-1


HVR-MRC1

1. SERVICE NOTE

1-1. POWER SUPPLY DURING REPAIRSIn this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off sothat the unit cannot operate.These following method is available to prevent this.

Method:Use the DC input terminal. (AC power adaptor/changer (AC-VQ1050B) and DK cable).

Note: ** is arbitrary value.

X

A

A

A

A

I

P

P

P

M

M

F

F

F

F

F

F

F

F

F

X

X

Yy

12

12

12

19

12

12

21

21

12

21

11

11

12

20

21

22

29

91

92

91

99

ZZ

01

02

03

91

**

**

01

02

**

**

01

02

**

01

**

**

00

**

**

85

**

Cause

Cash overflow by transfer rate delay ofCompactFlash.

The selection clip is not found.

The filesystem of CompactFlash is broken.

CompactFlash recognition error

Error related to i.LINK

It is generated the error by the power supplycontrol from main CPU to sub CPU.

It is generated the error by the powersupply control from sub CUP to eachdevice.

It could not enter to the sleep mode.

The input video stream is abnormal.

The recording animation could notcorrectly treat.

Communication abnormality betweenCompactFlash and main CPU.

i.LINK error.

It abnormal is generated by the file system.

Reset failure of PHY (Physical Layer)

Main CPU cannot be communicated withsub CPU.

Sub CPU cannot control each device.

Sub CPU farm is not written.

Fatal error of originating hardware.

Fatal error of originating software.

Reception buffer overflow.

Error code of main CPU firmware.

Self-diagnosis Code Corrective Action

Be sure that the CompactFlash you are using is the recommended type.

Be sure that the CompactFlash you are using is the recommended type.

Reformat the CompactFlash using this unit again, after reformattingthe CompactFlash using personal computer.

Check the type you are using.

Turn this unit off and then back on.








Reformat the CompactFlash using this unit.

There is particularly no solution








Xi LINK I:

ATA A:

Power Supply P:

MPEG/AVI M:

Other X:

Fatal Error F:

YMain 1y

Sub 2y

Other 9y

yPhysical Y1

Logical Y2

Other Y9

ZZWhen error is definedin the devise, the errorcode of it is displayed.

ERRORA:12:01

Self-diagnosis display: X:Yy:ZZ

LCD screen

1-2. SELF-DIAGNOSIS FUNCTIONWhen an error occurs the following warning indicators may appear on the LCD screen.And this unit is sent error code to camera.

1-2E


HVR-MRC1

対処

使用のコンパクトフラッシュが推奨のカードか確認する。

使用のコンパクトフラッシュが推奨のカードか確認する。

パソコンでコンパクトフラッシュのフォーマットを行った後，本機で再度コンパクトフラッシュのフォーマットを行う。電源を切り，再度電源を入れ直す。電源を切り，再度電源を入れ直す。

電源を切り，再度電源を入れ直す。


電源を切り，再度電源を入れ直す。電源を切り，再度電源を入れ直す。電源を切り，再度電源を入れ直す。



本機でコンパクトフラッシュのフォーマットを行う。電源を切り，再度電源を入れ直す。



特になし

電源を切り，再度電源を入れ直す。電源を切り，再度電源を入れ直す。電源を切り，再度電源を入れ直す。


1-1. 修理時の電源供給について本機では，安定化電源（8.4Vdc）からバッテリ端子に電源を供給した場合，約10秒後にシャットオフし，動作しなくなります。これを避けるため，下記の方法を用いてください。

方法：DC入力端子を使用する。（ACアダプタ/チャージャ（AC-VQ1050）とDKケーブルを使用する。）

X

A

A

A

A

I

P

P

P

M

M

F

F

F

F

F

F

F

F

F

X

X

Yy

12

12

12

19

12

12

21

21

12

21

11

11

12

20

21

22

29

91

92

91

99

ZZ

01

02

03

91

**

**

01

02

**

**

01

02

**

01

**

**

00

**

**

85

**

原因

コンパクトフラッシュの転送速度遅延によるキャッシュオーバーフロー。

選択クリップが見つからない。

コンパクトフラッシュのファイルシステムが壊れている。

コンパクトフラッシュ認識エラー。i.LINK関連のエラー。

メインCPUからサブCPUへの電源制御でエラー発生。サブCUPから各デバイスへの電源制御でエラー発生。

スリープモードに入れなかった。入力ビデオストリーム異常。

記録動画を正しく処理できなかったコンパクトフラッシュ－メインCPU間通信異常。

i.LINKエラー。ファイルシステムで異常発生。 PHY（Physical Layer）のリセット失敗。メインCPUがサブCPUとの通信ができない。サブCPUが各デバイスを制御できない。

サブCPUファームが書き込まれていない。ハードウェア起因の致命的なエラー。ソフトウェア起因の致命的なエラー。受信バッファオーバーフロー。メインCPUファームウェアのエラーコード。

自己診断コード

注：** は任意の値。

1-2. 自己診断機能エラーが発生した場合は，エラー内容に合わせてLCD画面にエラーコードが表示されます。また，カメラ側にエラーコードが送信されます。

ERRORA:12:01

自己診断表示：X:Yy:ZZ

LCD画面

X

i.LINK I:ATA A:電源 P:MPEG/AVI M:その他 X:致命的なエラー F:

Y

メイン 1yサブ 2yその他 9y

y

フィジカル Y1ロジカル Y2その他 Y9

ZZ

デバイスにエラーの規定があれば，そのコードを表示する。

2-1HVR-MRC1

2. DISASSEMBLY

Cut and remove the part of gilt which comes off at the point.(Be careful or some pieces of gilt may be left inside)

NOTE FOR REPAIR

• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.Do not insert the cable insufficiently nor crookedly.

• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.

• When installing a connector, don’t press down at wire of connector.It is possible that a wire is snapped.

2-2HVR-MRC1

2-1. IDENTIFYING PARTS

CF Base Cabinet ⋅ FP-202 Flexible Board

2-2-1. BASE CABINET SECTION ⋅ CF Base Cabinet ⋅ TK-071 Board

2-2-2. MAIN CABINET SECTION ⋅ CF-110 Board ⋅ LCD Block ⋅ SW-525 Board

- DISASSEMBLY FLOW -

2-2-3. ADAPTOR SECTION ⋅ CR-090 Board ⋅ Cabinet (BATT)

- DISASSEMBLY FLOW -

i.LINK Cradle

Memory Recording Unit

CF Main Cabinet ⋅ CF-110 Board ⋅ FP-201 Flexible Board ⋅ LC-095 Board ⋅ TK-071 Board

CF Door ⋅ SW-525 Board

Cabinet (CF) ⋅ CR-090 Board

Cabinet (BATT)

2-3HVR-MRC1

2-2. DISASSEMBLY

2-2-1. BASE CABINET SECTIONFollow the disassembly in the numerical order given.1 CF Base Cabinet (1-1 to 1-4)2 TK-071 Board (2-1 to 2-5)

HELPHELP

EXPLODED VIEW HARDWARE LIST

1CF Base Cabinet

2-1 (#46)2-2

1-2 (Claw)

1-3 (Claw)

1-4

2TK-071 Board

Main Cabinet Section(See Page 2-4)

1-1 (#53)

2-3

2-42-5

2-4HVR-MRC1

2-2-2. MAIN CABINET SECTIONFollow the disassembly in the numerical order given.1 CF-110 Board (1-1 to 1-5)2 LCD Block (2-1 to 2-2)3 SW-525 Board (3-1 to 3-9)


SW-525

CF-110

1CF-110 Board

1-2 (#46)

1-4 (Open)

1-3 (#11)

1-5

1-1

2LCD Block

2-1

2-2

3SW-525 Board

3-3 (#11)

3-8

3-9

A

A

3-6 (#46)

3-7 (#11)

3-4(Boss)

3-2(#2)

3-5

3-1

Note: Don't touch grease.

Note: On installation of the SW-525 board,adjust the position of switch of CF doorand S7010 of SW-525 board.

2-5HVR-MRC1

2-2-3. ADAPTOR SECTIONFollow the disassembly in the numerical order given.1 CR-090 Board (1-1 to 1-10)2 Cabinet (BTT) (2-1 to 2-6)


1CR-090 Board

1-1 (#2)

1-3

1-2 (#12)

1-5 (#12)

1-7 (#12)

1-9 (#12)

1-6

1-8

1-10

2Cabinet (BTT)

2-1 (#12)2-4(#12)

2-6

2-5(Open)

2-2

2-3

1-4

HELP

HELP

HVR-MRC1HELP

HELPSheet attachment positions and procedures of processing the flexible boards/harnesses are shown.

Terminal Retainer

Battery Terminal Harness

Hook

DC-IN Connector Harness

DC-IN Connector/Battery Terminal Harness

HVR-MRC1

LinkLink

3. BLOCK DIAGRAMS

OVERALL BLOCK DIAGRAM POWER BLOCK DIAGRAM

3-1HVR-MRC1

3. BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SW-525 BOARD

16

12

10

17

CN7001

MENU

STOP

REW

CAM_LINKCAM LINK

S7001

.M

m

S7002

sSTOP

MENU

S7003

S7004

H

PLAY

S7005

REC

S7009 S7006

REPEATS7007

>

S7008

13

9

18

5

8

6

14FF

REPEAT

PLAY

REC_ON

SW_PWR

SW_OFF_CN

LED_ON

POWERS7010

ON

OFF

Q7001LED DRIVE

5

9

11

4

CN2001

MENU

STOP

REW

CAM_LINK

8

12

3

16

13

15

7FF

REPEAT

PLAY

REC_ON

SW_PWR

SW_OFF_CN

LED_ON

IC3001

512MSDRAM

(3/5)

DDQ[0] - DDQ[31]

DA[0] - DA[12]

HDV/DV i.LINKINTERFACE

(1/5)

RESET(5/5)

IC4003

MRESET MRESET_R

CNA

CARD_DETECTCF_NDASP

POR-S3.3V

M3.3VIC1004

DC CONTROL(5/5)

IC1001

IC2003

CN8001CN8002CN4001

xCS0

xCD1xCD2

xRESET

xCS1xIORD

xIORWINTRQ

xCS0#CS0#CS1#DIOR#DIOW

DMARQ#DMACK

#RESET

xCD

xRESET

xCS1xIORDxIORWINTRQ

A00 - A02

D00 - D15

DA0 - DA2 A00 - A02

1314182024

IORDYIORDY34

xINPACKxINPACKxREGxREG

xDASP

COVER_STAT COVER_STAT

xDASP

363840

39, 3

7, 3

5

CN9004CN9005 CN4002

FP-203 FLEXIBLE BOARD

CR-090BOARD

TK-071 BOARD FP-202 FLEXIBLE BOARD

591915

2 C6D7

53

14

RESET(5/5)

IC100514

#RESET

BUFFER(1/5)

IC4002

3 CNA

CTL0, CTL1

PCLKLREQLPS

LKON

42

SUB CPU(4/5)

IC2001

MAIN CPU(2/5)

IC5001

16

30

10

35

39

8

34

9

11

38

60

X400124.576MHz

X500127MHz

3.0VH3.3VM3.3VM3.3VAS3.3VP3.3V1.8VA1.8V

ACV_UNREG

SET_UNREG

LC-095 BOARD

CF-110 BOARD

ND6001

LCD

CN6002CN8003CN8004

SCLA0

SDA

CSRES

ENA

SCLA0

SDA

CSRES

LCD_SCLLCD_A0

LCD_SDA

LCD_CS1LCD_RESET

ENA

75

3

11139

CN2002

75

3

11139

2

3250

810

12

426

810

12

426

FP-201FLEXIBLE BOARD

D6001, D6002(BACKLIGHT)

Q6001, Q6002LED DRIVE

1

RESET

PWR_CF0

SUB_S_RESET

MAIN_TO_SUB

SUB_FLMOD

I2C_SDAI2C_SCL

ENACOVER_STATLCD_SCLLCD_SDA

40

12

155

42142221

37

2

21

4

2943

20

SO, SI, SCK

XCS, XWP, XRESET

IC5002

EEPROM(2/5)

8, 1

, 24,

5, 3

D20,

F18

, E20

E17,

D19

, C19

3 - 1

2, 4

1, 4

3 - 4

6, 4

8

LD[0] - LD[7] D00 - D15

INTRQIORDY

DD[1] - DD[15]

1

B12A12

V3

C1

D3G1

Y5Y4

L1

D7009REC LAMP,CF ACCESS

z

6 - 3

15, 1

4, 1

8, 1

7

15, 1

4, 1

8, 1

7

12, 1

1, 1

5, 1

4

12, 1

1, 1

5, 1

4

HDV/DV

HDV-i.LINK, DV-i.LINKTPA+, TPA-, TPB+, TPB-

HDV-i.LINK, DV-i.LINKTPA+, TPA-, TPB+, TPB-

6 - 1

34,

5

A5, B

6

37 -

34

C7, A

6,B7

, A7,

A10,

A11

,C1

1, B

11

W16

, V16

, T17

, U20

,T1

9, P

19, N

18, M

18N1

9, P

20, T

20, T

18,

V20,

W17

, Y17

, V15

W9,

Y10

, V9

U9Y8

C2B1F3E3E1

CLKDC9 J1

Y15V14Y11

V10

W14W15W11

393834322818161412

13, 1

5, 1

7

50

202

4, 6

- 9,

11

,40

- 49

73234353742434445

18 -

20

262541

2 - 6

, 21

- 23,

27

- 31,

47

- 49

S8001COVER

OPEN/CLOSE

COMPACTFLASH

2627384239

RESET SWITCH(4/5)

A : VIDEO/AUDIO SIGNAL05

CN903HOT

SHOE

CN902HOT

SHOE

i.LINK CRADLE MEMORY RECORDING UNIT

EXEC

POWERSWITCH

(4/5)

IC2004

1

7

2

SW_OFF

4

PWR_

CF

3-2EHVR-MRC1

3-2. POWER BLOCK DIAGRAM ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SW-525 BOARD

CN2001CN7001

CN9002

CN9001

123

ACV_UNREG

UNREG

ACV_UNREG

UNREG

CN9005

F9002

F9001

CN4002

FP-203 FLEXIBLE BOARD

CR-090 BOARD TK-071 BOARD FP-202 FLEXIBLE BOARD

1

2

3

4

F1002

F1001

SET_

UNRE

G

Q1009

Q1008

Q1012D1003

D100

4Q1016

Q1015

VIN

IC1001

2623

RUN/SS128

RUN/SS213

BG1

BG2

TG1

TG2

22

1814

SW1

SW2

253031

SENSE2+

SENSE1+

SENSE2-

SENSE1-

1Vosense1

SWITCHINGQ1004 L1002

R1025,R1026

R1023,R1024

1.8V

A1.8V

SWITCHINGQ1005 L1001

FB1004

FB1005

FB1006

FB1002

FB2001

FB40

05

FB40

04

FB40

06

1211

Vosense2 9

15

S3.3VS3.3V

3.3V

SW_OFF_CN

SW_PWR

P3.3V

H3.3V

M3.3V

M3.

3VA

3.0V

IC10033V REG

(5/5)FB1003

Q1017

Q1018

IC2001

P20/ANI0

PWR_

SUB_

33

SW_O

FF

P130

P27/ANI7

P26/ANI6

P75

P74

P124/XT2/EXCLKS

P140/PCL/INTP6

P33/TI51/TO51/INTP4

P15/TOH0P16/TOH1/INTP5

32

26

25

6

33

41

17

16

36

7

PWR_LCD

PWR_CF0CARD_DETECT

PWR_MAIN_33

PWR_LCD

PWR_CF0

CARD_DETECT

PWR_MAIN_33

PWR_P33

PWR_P33

5

RESET SWITCH(4/5)

IC2003

EEPROM(2/5)

IC5002

512MSDRAM

(3/5)

IC3001

HDV/DV i.LINK INTERFACE(1/5)

IC4003

FB40

02FB

4003

MAIN CPU(2/5)

IC5001

RESET(5/5)

IC1004

FB50

03FB

1010

FB30

01

FB40

01

FB50

02

FB50

04

FB50

06

FB50

01

VDD1-VDD6

3.0V3.0V

CN8001CN8002CN4001

xCD1xCD

VccVcc

Vcc(A06)

VCC

xCD2

LC-095 BOARD

CF-110 BOARD

CN6002CN8003CN8004

1

CN2002

1 14 14

FP-201FLEXIBLE BOARD



FB6001

IC2004

12

4

FB1009

FB1008

FB1007

3

8

6SW_PWR SW_PWR

DCIN_AD

BATT_AD

IB_ENABLE

SLEEP

SW_OFF_CN

Q7001LED DRIVE 18

13

15

3.3V

SUB CPU(4/5)

DC CONTROL(5/5)

Q1014

PLUSMINUS_AMINUS_B

DC INJ901

BATT(+)

SW

BATT(-)

SIG

+

−

BT901BATTERY

TERMINAL S8,

96,

7

5, 6

3, 4

5, 6

3, 4

8, 9

6, 7

POWERS7010

ON

OFF

D7009REC LAMP,CF ACCESS

FB1001

R1042

Q101

1

Q101

3

R1004

Q1002

Q1001

R1040

ND6001

LCD

2, 8

, 15,

25,

34,

40

2

252627

50

272625

1338

2625

COMPACTFLASH

POWER SWITCH(4/5)

CN903HOT

SHOE

CN902HOT

SHOE

05

BATTERYDETECT

FL40

01

FL40

02

FL40

03

i.LINK CRADLE MEMORY RECORDING UNIT

R7001

Q1003, Q1006

DC INDETECT

Q1007, Q1010

PWR_CF

3.3V

R6004,R6005

1 V34 M RESET RST-VDD VOUT

53

#RES

ET

BUFFER(1/5)

IC4002 42POR-

5 4VIN VOUT

1CONT

IC10023.3V REG

(5/5)

2 3VIN5 VIN

VOUT

RESET(5/5)

IC1005

14 VDD VOUT

4-1HVR-MRC1

4-1. FRAME SCHEMATIC DIAGRAM4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

FRAME

CN902HOT SHOE

CN903HOT SHOE

S

CN9004HDV/DV

20 1

CN2001

1

20

CN4002

2 501 51CN40011 14

CN2002

TK-071 BOARD (SIDE B)

TK-071 BOARD (SIDE A)

CR-090 BOARD (SIDE A)

1 20CN7001

SW-525 BOARD

FLEX

IBLE

FLA

T CA

BLE

(FFC

-157

)

Attaching

2

50

1

51

114

1

14

CN8003

CN8004

CN8002

20 1

16 1

1

20

1

16

1 4 1 3

120

CN9001 CN9002

CN9005

12

56 89

7

34

FP-203FLEXIBLEBOARD

FP-202FLEXIBLEBOARD

1 51

51 1

FP-201FLEXIBLEBOARD

ND6001LCD

1 49

CF-110 BOARD (SIDE B)

CF-110 BOARD (SIDE A)

LC-095 BOARD (SIDE A)

LC-095 BOARD (SIDE B)

126

2

2549

50

5153

5254

114

CN6002

CN8001COMPACT FLASH

CONNECTOR

(Compact Flash)

J901DC IN

BT901BATTERY

TERMINAL

05

FLEX

IBLE

FLA

T CA

BLE

(FFC

-159

)

FLEX

IBLE

FLA

T CA

BLE

(FFC

-159

)

IC5002(EEPROM)

(Not supplied)

i.LINK CRADLEMEMORY RECORDING UNIT

HVR-MRC1

LinkLink

COMMON NOTE FOR SCHEMATIC DIAGRAMS

4-2. SCHEMATIC DIAGRAMS

TK-071 BOARD (2/5) (MAIN CPU)

TK-071 BOARD (1/5) (HDV/DV i.LINK INTERFACE)

TK-071 BOARD (5/5) (DC/DC CONVERTER)

CF-110 BOARD (CF CONNECTOR)

TK-071 BOARD (3/5) (SDRAM)

TK-071 BOARD (4/5) (SUB CPU)

SW-525 BOARD (CONTROL SWITCH)

FP-202 FLEXIBLE BOARD (HOT SHOE (MEMORY RECORDING UNIT))FP-203 FLEXIBLE BOARD (HOT SHOE (i. LINK CRADLE))CR-090 BOARD (DC IN, HDV/DV CONNECTOR)

LC-095 BOARD (LCD)

4-2HVR-MRC1

4-2. SCHEMATIC DIAGRAMS4-2. SCHEMATIC DIAGRAMS ENGLISH JAPANESEENGLISH JAPANESE

4-2. SCHEMATIC DIAGRAMS(ENGLISH)

When indicating parts by reference number, pleaseinclude the board name.

(For schematic diagrams)• All capacitors are in µF unless otherwise noted. pF : µ

µF. 50 V or less are not indicated except for electrolyticsand tantalums.

• Chip resistors are 1/10 W unless otherwise noted.kΩ=1000 Ω, MΩ=1000 kΩ.

• Caution when replacing chip parts.New parts must be attached after removal of chip.Be careful not to heat the minus side of tantalumcapacitor, Because it is damaged by the heat.

• Some chip part will be indicated as follows.Example C541 L452

22U 10UHTA A 2520

• Constants of resistors, capacitors, ICs and etc with XXindicate that they are not used.In such cases, the unused circuits may be indicated.

• Parts with differ according to the model/destination.Refer to the mount table for each function.

• All variable and adjustable resistors have characteristiccurve B, unless otherwise noted.

• Signal nameXEDIT → EDIT PB/XREC → PB/REC

• 2: non flammable resistor• 5: fusible resistor• C : panel designation• A : B+ Line• B : B– Line• J : IN/OUT direction of (+,–) B LINE.• C : adjustment for repair.(Measuring conditions voltage and waveform)• Voltages and waveforms are measured between the

measurement points and ground. They are referencevalues and reference waveforms.(VOM of DC 10 MΩ input impedance is used)

• Voltage values change depending upon inputimpedance of VOM used.)

Kinds of capacitorCase size

External dimensions (mm)

THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS(In addition to this, the necessary note is printed in each block)

The components identified by mark 0 or dotted line withmark 0 are critical for safety.Replace only with part number specified.

Les composants identifiés par une marque 0 sontcritiques pour la sécurité.Ne les remplacer que par une pièce portant le numérospécifie.

4-3HVR-MRC1

(JAPANESE)回路図共通ノート（他に必要なノートは各ブロックに記載してあります）【回路図ノート】・ケミコン，タンタルを除くコンデンサで，耐圧50V以下のものはその耐圧を省略。単位はすべてμF（pはpF）。

・チップ抵抗で指示のないものは，1／10W以下。kΩ＝1000Ω，MΩ＝1000kΩ・チップ部品交換時の注意取り外した部品は再使用せず，未使用の部品をご使用ください。タンタルコンデンサのマイナス側は熱に弱いため注意してください。

・チップ部品には下記のように表示したものがあります。　例 C 541 L 452

22U 10UHTA A 2520↑ ↑ ↑種類ケースサイズ外形寸法（mm）

・抵抗，コンデンサ，ICなど定数にXXがあるものは，使用していない事を示しています。このため，使用していない回路が記載されている事があります。

・印のある部品は，機種などにより異なりますので機能別マウント一覧表を参照してください。

・可変抵抗と半固定抵抗で，B特性の表示を省略。・信号名表記について，下記のような場合があります。XEDIT　→　EDIT　　　　　PB/XREC　→　PB/REC・2は不燃性抵抗。・1はヒューズ抵抗。・Cはパネル表示名称。・AはB＋ライン。・BはB－ライン。・JはBライン（＋，－）の入出力方向を示す。・Cは調整名称。【電圧・波形測定条件ノート】・電圧値及び信号波形は測定点対アース間の参考値。（デジタルマルチメータ；入力インピーダンス　DC10MΩ使用）

・使用テスタの入力インピーダンスにより電圧値が多少異なります。

0印の部品，または0印付きの点線で囲まれた部品は，安全性を維持するために重要な部品です。従って交換時は，必ず指定の部品を使用して下さい。

お願い図面番号で部品を指定するときは基板名又はブロックを併せて指定して下さい。

4-2. SCHEMATIC DIAGRAMS4-2. SCHEMATIC DIAGRAMS ENGLISH JAPANESEENGLISH JAPANESE

4-4HVR-MRC1

TK-071 (1/5)

NO MARK:REC/PB MODE

3.3

3.3

3.3

3.3

0

1.6

R0/P3.3

1

0

0.4

0.4

0

0

0

0

0

0

0

3.2

0

3.3

3.3

3.3

3.3

3.3

3.3

3.3

0

R1.8/P0

R1.8/P0

R1.8/P3.2

R1.8/P3.2

R1.8/P3.2

0

1.2

3.3

0.2

0.2

3.3

3.3

3.3

3.3

01.3

1.5

1.5

3.3

3.3

R:REC MODE P:PB MODE

3

G

6 9

F

B

H

7 10

C

05

8 11

D

B

G

12

E E

H

1

A

4

D

A

2

C

5

F

SET_UNREG_CN

DD[10]

DD[0]

DD[14]

DD[5]

DD[9]

DD[1]

DD[15]

DD[13]

DD[6]

DD[7]

DD[2]

DD[8]

DD[12]

DD[3]

DD[11]

DD[4]

H3.

3VV

V

CARD_DETECT

P3.3VA

C40

13

0.1u

B

C4017

0.1uB

C40

10

0.1u

B

C4019220p

B

C40

12

0.1u

B

C40140.1uB

C40

090.

1uB

C4018

1u

C400812p

CH50V

C4011

12pCH

50V

C40150.1u

B

C40064.7u

B6.3V

C40164.7uB 6.3V

CTL0

LPS

CTL1

LREQ

LKON

P3.3V P3.3V

CNA

PCLK

LD[2]

LD[6]

LD[4]

LD[5]

LD[0]

LD[3]

LD[7]

LD[1]

FB4006

FB4004

FB40

03

FB4002 FB4005FL4001

FL40

03

FL4002

IC4003

TSB41AB2PAPRHDV/DV i.LINK

INTERFACE

1 LREQ

2 SYSCLK

3 CNA

4 CTL0

5 CTL1

6 D0

7 D1

8 D2

99 D3

10 D4

11 D5

12 D6

13 D7

14 PD

15 LPS

16 NC

17

DG

ND

1

18

DG

ND

2

19

C/L

KO

N

20

PC

0

21

PC

1

22

PC

2

23

#IS

O

24

CP

S

25

DV

DD

1

26

DV

DD

2

27

TES

TM

28

SE

29

SM

30

AV

DD

1

31

AV

DD

2

32

AG

ND

1

33AGND2

34TPB0-

35TPB0+

36TPA0-

37TPA0+

38TPBIAS0

39AGND3

40R0

41R1

42AVDD3

43TPB1-

44TPB1+

45TPA1-

46TPA1+

47TPBIAS1

48AGND4

49

AG

ND

5

50

AG

ND

6

51

AV

DD

4

52

AV

DD

5

53

#RES

ET

54

FILT

ER0

55

FILT

ER1

56

PLL

VD

D

57

PLL

GN

D1

58

PLL

GN

D2

59

XI

60

XO

61

DV

DD

3

62

DV

DD

4

63

DG

ND

3

64

DG

ND

4

65

NC

R40626200

R40

60

1k

R406556

R4052XX

R4053 XX

R4054 XX

R40

591k

R406756

R4063

150

R4051 1k

R40

56

0

R40

57

0

R4050 47

R4055 10k

R4048XX

R40

5833

k

R406856

R404233k

R40

61

1k

R406456

CL4004

R404710k

SET_UNREG

R4071

0

R404310k

IC4002

BUFFERTC7S08FU(TE85R)

12

3 45

R4046

XX

C40050.1u

B10V

SUB_TO_PHY

S3.3V

ACV_UNREG

R4069

0

R4070

0

R40

38

4700

R4018 82

CF_NDASPR4025 33

R4020 33

DD[5]

R4019 82

DMARQ

R4005 33

R4013 33

DD[4]

R40

39 10k

DD[7]

INTRQ

DA2

R4011 33

R4029 33

R4035 10k

R4030 33

R4009 33

R4012 33

R4023 22

R4034 10k

R40

40

100k

M3.3V

DD[11]

H3.3V

#DIOW

R4003 33

DD[12]

DD[13]

R4026 33

R4004 33

R4001 33

GND

DD[0]

DD[3]

CARD_DETECT

R4010 33

R4022 33

C4003

10uB 6.3V

C4002

0.1u

B10V

R4007 33

DA1

DD[14]

#CS1

R4015 22

R4021 82

DA0

#DIOR

DD[6]

R4032 33

R4036 5600

#DMACK

R4031 33

R4008 33

#PDTAG

DD[2]

R4016 22

COVER_STAT

#CS0

R4028 33

FB4001

R4006 33

R4033 33

DD[15]

R4027 XX

IORDY

DD[9]

R4002 33

DD[8]

R4024 33

DD[1]

DD[10]

X400124.576MHz

D001NSAD500H-T1-A

R4045XX

R4044XX

R4049

XX

CN4002 20P

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

R40665100

C4001

0.01u

B25V

C40070.01u B

25V

GND

R4037 10k

CN4001 51P

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

R4072

XX

R4073

XX

LF40011

2

3

4

5

6

7

8

D10

D01

xREG

GND(A03)

GND(xCSEL)

GND(A07)

xIORD

xCS0

D13

D03

GND(xCD2)

D08

A00

IORDY

GND(A05)

INTRQ

GND(A09)

xCS1

D06

D11

COVER_STAT

D02

xDASP

A02

GND(xVS2)

Vcc

xIORW

GND(A10)

D14

D04

GND

D09

D00

xINPACK

GND(A04)

Vcc

GND(A08)

GND(xVS1)

D07

D12

GND

GND(xIOIS16)

xPDIAG

A01

xRESET

Vcc(A06)

GND(xWE)

GND(xATA_SEL)

D15

D05

xCD

REG_GND

REG_GND

REG_GND

UNREG

UNREG

N.C

ACV_UNREG

ACV_UNREG

DETECT

N.C

REG_GND

TPB+

TPB-

TPA+

TPA-

REG_GND

REG_GND

REG_GND

REG_GND

REG_GND

XX MARK:NO MOUNT

HDV/DV i.LINK INTERFACETK-071 BOARD (1/5)

FP-201 Flexible

43

1 2

43

1 2

431 2

4

31

2

123

5

4

CF-110CN8002

(Page 4-9)

Through the

FP-202

(Page 4-12)

#RESET

FLEXIBLELND001 – LND020

POR-

4-5HVR-MRC1

TK-071 (2/5)

NO MARK:REC/PB MODE

0

0

3.2

3.2

0.8

3.2

0

Note:Two interchangeable kinds of ICare used for IC5002. It is includedin TK-071 complete board thoughneither of these are supplied.

XX MARK:NO MOUNT

MAIN CPUTK-071 BOARD (2/5)

3

G

6 9

F

B

H

7 10

C

05

8 11

D

B

G

12

E E

H

1

A

4

D

A

2

C

5

F

DD

Q[2

8]

DD

[14]

DD

Q[2

7]

DD

[13]

DD

Q[2

6]

DD

[12]

DD

Q[2

5]

DD

[11]

DD

Q[2

4]D

D[1

0]

DD

Q[2

3]

DD

[9]

DD

Q[2

2]

DD

[8]

DD

Q[2

1]

DD

[7]

DD

Q[2

0]

DD

[6]

DD

Q[1

9]

DD

[5]

DD

Q[1

8]

DD

[4]

DD

Q[1

7]

DD

Q[1

6]

DD

Q[1

5]

DD

[1]

DD

Q[1

4]

DD

[0]

DD

Q[1

3]

DD

Q[1

2]

DD

Q[1

1]

DD

Q[1

0]

DD

Q[9

]

DD

Q[8

]

LD[4

]

DD

Q[7

]

LD[7

]

DD

Q[6

]

LD[6

]

DD

Q[5

]

LD[5

]

DD

Q[4

]

LD[3

]

DD

Q[3

]

LD[2

]

DD

Q[2

]

DD

Q[3

1]

LD[1

]

DD

Q[1

]

DD

Q[3

0]

LD[0

]

DD

Q[0

]

DD

Q[2

9]

DD

[15]

DD

[2]

DD

[3]

C50180.1u

C50230.1u

C50

330.

001u

C50200.001u

C50240.01uB

25V

C50050.1u

C50044.7u B

6.3V

C50014.7u B

6.3V

C50254.7uB

6.3V

C5026 220pB50V

C5032

0.1uB10V

C50310.1u

B10V

C500310u B

6.3V

C500210u B

6.3V

C50170.1u

C50130.1u

C50100.1u

C50210.1u

C50150.1u

C50190.1u

C50220.1u

C5006

0.1u

C50080.1u

C50140.1u

C50110.1u

C50090.1u

C50340.1u

B10V

C50160.1u

C5027 XX

C50300.1u

B 10V

C50120.1u

C50070.1u

C5029 XX

CL5

010

CL5

014

CL5

013

CL5

012

CL5

011

CL5

015

CL5

008

CL5

009

CL5

016

CL5

007

CL5

005

CL5

001

CL5

004

CL5

006

CL5

003

CL5

018

CL5

017

CL5

019

CL5043

CL5

002

M3.3VA

DMARQ

IORDY

GND

INTRQ

A1.8V

#PDTAG

1.8V

M3.3V

PCLK

CLK

D

DA

[4]

DA

[10]

DQ

M3

#DIOR

LCD_SDA

#CS1

LKON

#WE

#DMACK

BA

0

DA

[3]

#DIOW

#CS0

LPS

LCD_CS1

#CA

S

BA

1

DA

[2]

CTL0

DA

[8]

LCD_A0

#CS

I2C_SCL

DQ

M1

DA2

LREQ

DA

[0]

DA

[6]

DA

[11]

#RA

S DA

[5]

I2C_SDA

DA

[12]

DQ

M0

CLK

E

DA

[1]

DA

[7]

DA0

DQ

M2

MAIN_TO_SUB

DA1

LCD_SCL

DA

[9]

CTL1

DD

Q[2

0]

LD[6

]

DD

Q[2

5]

DD

Q[1

3]

DD

Q[2

4]

DD

[0]

DD

[13]

DD

Q[4

]

DD

[4]

DD

Q[1

2]

DD

Q[2

2]

DD

Q[1

5]

LD[1

]

DD

Q[6

]

DD

Q[1

0]

LD[7

]

DD

Q[1

6]

DD

[14]LD

[2]

DD

Q[1

1]

DD

Q[2

]

DD

[5]

DD

Q[1

7]

DD

Q[7

]

DD

[9]

DD

Q[1

4]

LD[3

]

DD

[3]

DD

Q[1

]

DD

[10]

DD

Q[0

]

DD

[1]

DD

Q[3

0]

DD

[12]

DD

Q[2

9]

LD[5

]

DD

Q[1

8]

DD

Q[2

3]

DD

[7]

DD

Q[2

1]

LD[0

]

DD

Q[5

]

DD

Q[8

]

DD

[2]

DD

Q[2

7]

DD

Q[9

]

DD

[11]

DD

Q[1

9]

LD[4

]

DD

Q[3

1]

DD

Q[3

]

DD

[15]

DD

Q[2

6]

DD

[6]

DD

Q[2

8]

DD

[8]

FB5005

FB5003

FB5002

FB5001

FB5004

IC5001IND60C32AMAIN CPU

B16

AV

2_V

ALI

D

A16

AV

2_S

OP

C16

AV

2_S

OF

B13

AV

2_D

ATA

7

C13

AV

2_D

ATA

6

A14

AV

2_D

ATA

5

B14

AV

2_D

ATA

4

C14

AV

2_D

ATA

3

A15

AV

2_D

ATA

2

B15

AV

2_D

ATA

1

D14

AV

2_D

ATA

0

C15

AV

2_C

LK

L19

AV

1_V

ALI

D

L18

AV

1_S

OP

M20

AV

1_S

OF

K20

AV

1_D

ATA

7

K18

AV

1_D

ATA

6

J20

AV

1_D

ATA

5

J19

AV

1_D

ATA

4

J17

AV

1_D

ATA

3

H19

AV

1_D

ATA

2

G20

AV

1_D

ATA

1

F20

AV

1_D

ATA

0

L20

AV

1_C

LK

T3

AV

3_C

LK

P3

AV

3_D

ATA

0

N3

AV

3_D

ATA

1

N1

AV

3_D

ATA

2

K3

AV

3_D

ATA

3

K2

AV

3_D

ATA

4

J1

AV

3_D

ATA

5

J2

AV

3_D

ATA

6

J4

AV

3_D

ATA

7

U1

AV

3_S

OF

T4

AV

3_S

OP

U2

AV

3_V

ALI

D

Y17

DD

14

W17

DD

13

V20

DD

12

T18

DD

11

T20

DD

10

P20

DD

9

N19

DD

8

M18

DD

7

N18

DD

6

P19

DD

5

T19

DD

4

U20

DD

3

T17

DD

2

V16

DD

1

W16

DD

0

V14

DIO

W-

Y15

DIOR-

W11DMACK-

W9

DA0

Y10

DA1

V9DA2

U9CS0-

Y8CS1-

V10

RESET-

W15DMAREQ

Y11

INTRQ

W14IORDY

M19PDIAG-

Y18

ATAEN

C12

LCLK

B6CTL1

A5CTL0

D7LREQ

A12

LPS

C6PCLK

D12

PINT

B12

LINKON

V3RST-

G1GPIO7

C2GPIO6

B1GPIO5

F3GPIO4

E1GPIO3

E3GPIO2

C1GPIO1

D3GPIO0

Y4SCL

Y5SDA

C18

UART_TX

A20

UART_RX

W20XPRINT

V19

XPCS-

XPRD- W18

XPWR- V17

XPA2 V18

XPA1 W19

Y20

XPA0

M1

PLL1FILTER

M2

PLL2FILTER

A9PLL3FILTER

L1CLK

V5XPD0

W5

XPD1

W6

XPD2

Y6XPD3

V7XPD4

W7

XPD5

Y7XPD6

V8XPD7

W8

XPO8

V12

XPD9

U12

XPD10

Y13

XPD11

W13XPD12

V13

XPD13

Y14

XPD14

U16

XPD15

C19

SRESET-

E17

SCS-

D19

SWE-

D20

SD

F18SI

E20

SCLK

A2TRST

B2

TDO

B3

TDI

C4

TMS

B5

TCK

U19

DQ

31

U18

DQ

30

R19

DQ

29

R20

DQ

28

B11

LD7

V15

DD

15

U5

AV

4_V

ALI

D

C7

LD0

V4

AV

4_S

OP

A6

LD1

W4

AV

4_S

OF

B7

LD2

Y3

AV

4_D

ATA

A7

LD3

W3

AV

4_C

LK

A10

LD4

R3

AV

3_D

REQ

A11

LD5

H2

AV

3_IR

C

C11

LD6

K19

DQ

27

J18

DQ

26

H20

DQ

25

H18

DQ

24

G19

DQ

23

G18

DQ

22

G17

DQ

21

E19

DQ

20

E18

DQ

19

C20

DQ

18

D18

DQ

17

B20

DQ

16

B19

DQ

15

A19

DQ

14

B17

DQ

13

C17

DQ

12

D16

DQ

11

A18

DQ

10

C10

DQ

9

D9

DQ

8

A8

DQ

7

B8

DQ

6

C8

DQ

5

A4

DQ

4

C5

DQ

3

B4

DQ

2

A3

DQ

1

D5

DQ

0

C9

CLK

D

A17

CK

E

W2

A0

W1

A1

V2

A2

U3

A3

P4

A4

R2

A5

R1

A6

P2

A7

N2

A8

M4

A9

K1

A10

J3

A11

T2

A12

E4

BA

0

D2

BA

1

H1

DQ

M0

H3

DQ

M1

G3

DQ

M2

F1

DQ

M3

G4

WE-

F2

CA

S-

E2

RA

S-

D1

CS

-

U11

VS

SA

L3

VS

S_P

LL1

M3

VS

S_P

LL2

B9

VS

S_P

LL3

W10

VS

S1

U14

VS

S2

P17

VS

S3

M17 VSS4

A1 VSS5

D4 VSS6

D8 VSS7

D13

VSS8

D17

VSS9

H4 VSS10

H17

VSS11

J9 VSS12

J10 VSS13

J11 VSS14

J12 VSS15

K9 VSS16

K10 VSS17

K11 VSS18

K12 VSS19

L9 VSS20

L10 VSS21

L11 VSS22

L12 VSS23

M9

VSS24

M10 VSS25

M11 VSS26

M12 VSS27

N4 VSS28

N17

VSS29

U4 VSS30

U8 VSS31

U13

VSS32

U17

VSS33

D6 VDD181

D11

VDD182

D15

VDD183

F4 VDD184

F17 VDD185

K4 VDD186

L17 VDD187

R4 VDD188

R17

VDD189

U6 VDD1810

U10

VDD1811

U15

VDD1812

Y9 VDD331

Y1 VDD332

Y16 VDD333

R18

VDD334

N20

VDD335

G2 VDD336

P1 VDD337

V1 VDD338

Y2 VDD339

U7 VDD3310

W12 VDD3311

Y19 VDD3312

P18 VDD3313

K17 VDD3314

F19 VDD3315

B18 VDD3316

A13 VDD3317

B10 VDD3318

C3 VDD3319

T1 VDD3320

V6 VDD3321

L2 VDD18_PLL1

L4 VDD18_PLL2

D10

VDD18_PLL3

Y12 VDD18A

V11 VDD33A

JL5009

JL5008

JL5010

JL5004

JL5001

JL5005

JL5003

JL5006

JL5007

JL5002

JL5011

R5046100

R5036

10k

R50

2147

00

R50

1847

00

R50

13X

X

R50

14X

X

R50

09X

X

R50

06X

X

R50

05X

X

R50

02X

X

R5034 33k

R50

2347

00

R5029 XX

R5030 XX

R5031 XX

R5032 XX

R5033 XX

R50

19X

X

R5035 1k

R5041

10k

R50

17X

X

R50

04X

X

R5027 4700

R50

2233

R5038

10k

R50

2047

00

R50

26X

X

R50

16X

X

R50

12X

X

R50

10X

X

R50

07X

X

R50

03X

X

R50

11X

X

R50

25X

X

R50

08X

X

R50

01X

X

R5028 0

R50

15X

X

X500127MHz

143

2

R5040

10k

R5039

10k

R5037

10k

SUB_FLMOD

FB5006

C50280.01u

R50

2456

IC5002 (Note)AT45DB081B-CNUAT45DB081D-SU

EEPROM

1

SI

2

SCK

3

xRESET

4

xCS

5xWP

6VCC

7GND

8SO

TMS

TCK

TDI

TDO

TRST

VCC

GND

VCC

TXD

VSS

RXD

A1.8V

M3.3VA

1.8V

M3.3V

MRESET_R

#RESET

LCD_RESET

SUB_S_RESET

4-6HVR-MRC1

TK-071 (3/5)

3

G

6

F

B

H

C

05

D

B

G

E E

H

1

A

4

D

A

2

C

5

F

DA[0]

DA[1]

DA[2]

DA[3]

DA[4]

DA[5]

DA[6]

DA[7]

DA[8]

DA[9]

DA[10]

DDQ[0]

DDQ[9]

DDQ[1]

DDQ[12]

DDQ[8]

DDQ[6]

DDQ[5]

DDQ[7]

DDQ[11]

DDQ[13]

DDQ[14]

DDQ[3]

DDQ[4]

DDQ[10]

DDQ[2]

DDQ[15]

DDQ[23]

DDQ[26]

DDQ[20]

DDQ[22]

DDQ[19]

DDQ[21]

DDQ[27]

DDQ[25]

DDQ[28]

DDQ[17]

DDQ[18]

DDQ[16]

DDQ[24]

DDQ[29]

DDQ[30]

DDQ[31]

C30014.7u

B6.3V

C30150.1u

C30120.1u

C30090.1u

C30080.1u

C30100.1u

C30110.1u

C30070.1u

C30130.1u

C30050.1u

C30060.1u

C30040.1u

C30030.1u

C30020.1u

C30140.1u

DDQ[12]

DDQ[20]

DDQ[28]

DDQ[15]

DDQ[23]

DDQ[17]

DDQ[2]

DDQ[26]

DDQ[10]

DDQ[21]

DDQ[29]

DDQ[24]

DDQ[7]

DDQ[16]

DDQ[25]

DDQ[14]

DDQ[13]

DDQ[11]

DDQ[6]

DDQ[18]

DDQ[0]

DDQ[19]

DA[0]

DDQ[3]

DDQ[9]

DDQ[1]

DDQ[31]

DDQ[22]

DDQ[30]

DDQ[8]

DDQ[27]

DDQ[5]

#WE

BA1

CLKE

CLKD

DQM3

#CAS

BA0

DQM2

#CS

DQM1

#RAS

DQM0

M3.3V

DA[12]

DA[5]

DA[4]

DA[10]

DA[6]

DA[3]

DA[9]

DA[2]

DA[7]

DA[1]

DA[8]

DA[11]

DDQ[4]

FB3001

IC3001 512M SDRAM

K4M513233C-DN75T

G8 A0

G9 A1

F7 A2

F3 A3

G1 A4

G2 A5

G3 A6

H1 A7

H2 A8

J3 A9

G7 A10

J7 BA0

H8 BA1

R8 DQ0

N7 DQ1

R9 DQ2

N8 DQ3

P9 DQ4

M8

DQ5

M7

DQ6

L8 DQ7

L2 DQ8

M3

DQ9

M2

DQ10

P1 DQ11

N2 DQ12

R1 DQ13

N3 DQ14

R2 DQ15

E8 DQ16

D7 DQ17

D8 DQ18

B9 DQ19

C8 DQ20

A9 DQ21

DQ22C7

DQ23A8

DQ24A2

DQ25C3

DQ26A1

DQ27C2

DQ28B1

DQ29D2

DQ30D3

DQ31E2 DQM0 K9

DQM1 K1

DQM2 F8

DQM3 F2

CSN J8

WEN K8

RASN J9

CASN K7

CKE J2

CLK J1

NC E3

NC E7

A12 H3

NC H7

A11 H9

NC K2

NC K3

VDD A7

VDD F9

VDD L7

VDD R7

VDDQ B2

VDDQ B7

VDDQ C9

VDDQ D9

VDDQ E1

VDDQ L1

VDDQ M9

VDDQ N9

VDDQ P2

VDDQ P7

VSS A3

VSS F1

VSS L3

VSS R3

VSSQ B3

VSSQ B8

VSSQ C1

VSSQ D1

VSSQ E9

VSSQ L9

VSSQ M1

VSSQ N1

VSSQ P3

VSSQ P8

R300233

R300133

GND

CL3003

SDRAMTK-071 BOARD (3/5)

M3.3V

4-7HVR-MRC1

TK-071 (4/5)

NO MARK:REC/PB MODE

3.30

0

0

3.2

3.2

0

1.3

0

1.8

0

2.9

3.3

3.3

3.3

0

0 0 0 0 0

R1/

P0.

6

R1/

P0.

5

R0/

P3.

2

3.2

3.2

3.2

2

0.7

1

1

0

R0/P3.3

0

3.3

3.3

3.3

3.3

0

R0/

P3.

3

3.3

3.3

3.3

3.3

3.3

0102.5

3.3

0

3.23.3

3.3

R:REC MODE P:PB MODE

3

G

6 9

F

B

H

7 10

C

05

8 11

D

B

G

12

E E

H

1

A

4

D

A

2

C

5

F

SCL

SDA

#RES

A0

#CS_CN

ENA

C20170.1u

B10V

C20220.1u

B10V

C20

030.

01u

B

25V

C20184.7u

B6.3V

C20

070.

01u

B

25V

C2019XX

C20

100.

01u

B

25V

C20

020.

01u

B

25V

C20

050.

01u

B

25V

C2006

0.1uB

10V

C20

090.

01u

B25V

C2020XX

C2004

0.1uB

10V

C20

110.

01u

B

25VC

2008

0.01

uB

25V

LCD_CS1

LCD_A0

LCD_SCL

LCD_SDA

R20

04

33k

R20

02

33k

R20

01

33k

R20

06

33k

R20

08

33k

R2007220k

R20

05

33k

R20

03

33k

R2033

1k

R2039

XX

R2034

3300

R2038

3300

R2035

3300

R2036

3300

R2037

3300

R20

4033

k

R20

4333

k

R20

4133

k

R20111k

R20121k

R20131k

R20171k

R20161k

R20141k

R20151k

IC2001

UPD78F0513GA(S)-8EU-E2-A

1 P60/SCL0

2 P61/SDA0

3 P62/EXSCL0

4 P63

5 P33/TI51/TO51/INTP4

6 P75

7 P74

8 P73/KR3

9 P72/KR2

10 P71/KR1

11 P70/KR0

12

P32/INTP3/OCD1B

13

P31

/IN

TP2/

OC

D1A

14

P30

/IN

TP1

15

P17

/TI5

0/TO

50

16

P16

/TO

H1/

INTP

5

17

P15

/TO

H0

18

P14

/RxD

6

19

P13

/TxD

6

20

P12

/SO

10

21

P11

/SI1

0/R

xD0

22

P10

/xS

CK

1/Tx

DO

23

AV

REF

24

AV

SS

25P27/ANI7

26P26/ANI6

27P25/ANI5

28P24/ANI4

29P23/ANI3

30P22/ANI2

31P21/ANI1

32P20/ANI0

33P130

34P01/TI010/TO00

35P00/TI000

36P140/PCL/INTP6

37

P12

0/IN

TP0/

EXLV

I

38

P41

39

P40

40

RES

ET

41

P12

4/X

T2/E

XC

LKS

42

P12

3/X

T1

43

FLM

OD

44

P12

2/X

2/EX

CLK

/OC

D0B

45

P12

1/X

1/O

CD

0A

46

REG

C

47

VS

S

48

VD

D

SLEEP

PWR_MAIN_33

CF_NDASP

PWR_SUB_33

PWR_CF

CNA

PWR_LCD

C20

161u B

10V

DCIN_AD

SW_OFF

CL2012

CL2004

PWR_P33

CL2042

PWR_BATT

CL2041

CL2

026

R2026 10k

R2031

XX

R2047

XX

BATT_AD

IB_ENABLE

R20

4433

k

R20

4633

k

R20

4933

k

R204510k

R2048

0

MAIN_TO_SUB

LCD_SCL

LCD_SDA

SUB_TO_PHY

I2C_SCL

I2C_SDA

SUB_FLMOD

COVER_STAT

R20181k

R20191k

R20201k

R20

09

33k

R20

10

33k

GND

C20

120.

01u

B

25V

C20

130.

01u

B

25V

C20

010.

01u

B

25V

JL2006

JL2005

JL2002

JL2003

JL2001

JL2007

JL2004

JL2008

3.0V

R20

2133

00

R20

2233

00

R2050

XX

R2023 XX

R20

53

33k

S3.3V

FB2001

IC2003

SWITCH

SUB CPU

POWER SWITCH

RESETTC7S32FU(TE85R)

12

345

IC2004TC7S32FU(TE85R)

12

345

C20230.1u

B10V

R20

56 XX

R205510k

R20

57 XX

R2058 XX

CARD_DETECT

R20

63

XX

IC2005XX

12

3 45

R2062XX

R2061XX

R20

59

XX

C2024XX

R2064

0

R20

65

XX

CN2002 14P

1

2

3

4

5

6

7

8

9

10

11

12

13

14

R204233k

R20

3233

k

R20

28 10k

R20

2710

k

CN2001 20P

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

TXD

RXD

RESET

RXD

CLK

VCC

FLMOD

VSS

DATA

TXD

GND

3.3V

LED_ON

SW_PWR

SW_OFF_CN

REC_ON

STOP

REW

PLAY

FF

CAM_LINK

MENU

REPEAT

GND

GND

GND

GND

GND

GND

GND GND

SCL

GND

SDA

GND

A0

GND

CS

GND

RES

GND

ENA

GND

3.0V

XX MARK:NO MOUNT

SUB CPUTK-071 BOARD (4/5)

SW-525CN7001

Flexible Flat Cable(FFC-157)

Through the

(Page 4-11)

CF-110CN8004


Through the

(Page 4-9)

MRESET_RMRESET

LCD_RESET

SUB_S_RESET

4-8HVR-MRC1

TK-071 (5/5)

NO MARK:REC/PB MODE

0

6.1

0

6.1

8

1.8

1.8

2.9

3.5

3.3

7.9 3.3

2.8

5.1

8.2

2.8

5

0.7

3.5

7.8

6.8

1.8

2.9

1.5

1.8

1.76.1

0.8

5

0

0

1

3.3

0.6

0.8

3.3

3.3

6.1

5.1

3.3

3.3

0

0

2.3

2.3

2.8

0

0

7.2

2.7 8

7.2

2.72.3

7.2

88

0

0

0

2.3

3.3

8

8 8

3.3

3.3 3

3.3

3.3 3.3

0

3.3 3.3

0

3.3 3.3

1.8

3.3 3.3

0

1.8

0

3.3 1.8

3.3

3.2

3.3 1.9

3.3

3.3

3

G

6 9

F

B

H

7 10

C

05

8 11

D

B

G

12

E E

H

1

A

4

D

A

2

C

5

F

S3.3V

C10100.1uB

10V

C10440.1uB

C10040.01uB

C10294.7u

B

C10284.7u

B

C1003

10u

C

C10461u

C10411uB

C101210u

C10V

C10401uB

C10471u

C1048

1u

C10221u B

10V

C10491u

C10150.1u

B 10V

C1032

4.7uB

C1033

4.7uB

C10380.1u B

C10390.1u B

C10421u

B10V

C10060.01uB

C10340.1u

B 10V

C1025

1u B

10V

C10050.01uB

C1024100p

CH50V

C10080.1u

B 10V

C10070.01uB

C10191000p

50V

C

C10450.1u

B

C10210.001u

B50V

C1020100pCH50V

C10181000p

50V

C

C101310uC

C10091u B

10V

C10110.1uB

10V

C10140.1u

B10V

C102627p

CH50V

C103710u

B

C103610u

B

C103510u

B

CL1001

CL1002

D1003RSX101VA-30TR

D1001RB520CS-30T2R

D1004RSX101VA-30TR

D1002RB520CS-30T2R

IB_ENABLE

S3.3V

PWR_MAIN_33

PWR_LCD

M3.3V

PWR_BATT

PWR_P33

PWR_CF

GND

BATT_AD

DCIN_AD

FB1010

FB1001

FB10073V REG

3.3V REG

FB1006

FB1005

F1002

F1001 (1.4A/32V)

(1.4A/32V)

IC1005BU4325FVE-TR

12

345

IC1004BU4325FVE-TR

12

345

IC1003TK11130CSCL-G

1

CO

NT

2

GN

D

3

NC

4

VOUT

5VIN

IC1001LTC3728LXCUH#TR-R5

1Vosense1

2PLLFLTR

3PLLIN

4FCB

5ITH1

6SGND

733VOUT

8ITH2

Vos

ense

2

9

NC

10

SEN

SE2

-

11

SEN

SE2

+

12

RU

N/S

S2

13

TG2

14

SW

2

15

NC

16

17 BOOST2

18 BG2

19 PGND

20 INTVCC

21 EXTVCC

DCCONTROL

Q1003,Q1006BATTERY DETECT

22 BG1

23 VIN

24 BOOST1

SW

1

25

TG1

26

PG

OO

D

27

RU

N/S

S1

28

NC

29

SEN

SE1

+

30

SEN

SE1

-

31

NC

32 33

Q1016RTF015P02TL

Q1007LSK3541FS8T2L

Q1008RTQ035P02TR

1

3

4

256

Q1017RTQ035P02TR

1

3

4

256

Q1018RTQ035P02TR

1

3

4

256

Q1009RTQ035P02TR

1

3

4

256

Q1005FDS6986AS

87

2

1

65

4

3

Q1004FDS6986AS

87

2

1

65

4

3

Q1002DTC115TMT2L

Q1010DTC115TMT2L

Q1001DTC115TMT2L

Q1006DTA124EE-TL

Q1003

DTC144EMT2L

Q1014DTC144EMT2L

R103933k

R1035 1k

R10093600

R1004

10

R1019

1M

R1025 0.051

R1024 0.051

R1007120k

R1023 0.051

R10101800

R100618k

R100851k

R100556k

R100356k

R1026 0.051

R1020

XX

R100256k

R103633k

R1040

2.2

R103733k

R103833k

R1016

XX

R103116k

R1022

XX

R1011

XX

R103020k

R1012

270k

R1021

0

R1018

XX

R1015

0

R104147k

R1017

XX

R102810k

R102733k

SLEEP

R1001220k

Q1012RTQ035P02TR

1

3

4

256

R10341M

R1033

270k

Q1013

DTC115EETL

Q1011

DTC115EETL

SW_OFF

PWR_SUB_33

SET_UNREG

S3.3V

3.0V

H3.3V

M3.3V

M3.3VA

P3.3V

1.8V

A1.8V

ACV_UNREG

IC1002S-812C33BPI-C4NTFG

1

NC

2

VIN

3

VOUT

4 VSS

VIN5

ON/OFF6

S3.3V

C1002

1u B

10V

C1001

1u B

10V

R1042

0

D1006MAZS120008SO

D1005MAZS120008SO

C1017

0.01uB

25V

FB1003

FB1002

B+ SWITCH

INVERTER

DC IN DETECT

DC IN DETECT

NVERTER

INVERTER

SWITCHING

SWITCHING

INVERTER

B+ SWITCH

B+ SWITCH

B+ SWITCH

RESET

RESET

INVERTER

B+ SWITCH

B+ SWITCHB+ SWITCH

FB1008

FB1009

C10430.01uB

FB1004

R1029750

R1043

100k

R1044

100k

C10

161u

B10

V

R10451k

C103010u

B6.3V

C103110u

B6.3V

L1001

4.7uH

L1002

4.7uH

C10230.001uB50V

R10135600

R101410k

C102727pCH50V

R10321k

Q1015RTF015P02TL

SPWR

XX MARK:NO MOUNT

DC/DC CONVERTERTK-071 BOARD (5/5)

VDD

GNDVOUT

SUB

CT

VDD

GNDVOUT

SUB

CT

MRESET

POR-

• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.

4-9HVR-MRC1

CF-110

Note: CN8001 is not supplied, but this is included in CF-110 complete board.

C

3

G

6 9

F

B

H

7 10

C

05

8 11

D

B

G

12

E E

H

1

A

4

D

A

2

C

5

F

3.0V

C80010.01u

GND

R8009 XX

R8008 XX

R8036 XX

R8030 XX

R8033 XX

R8002 XX

R8027 XX

R8029 XX

R8013 XX

R8028 XX

R8007 XX

R8012 XX

R8003 XX

R8010 XX

R8032 XX

R8034 XX

R8006 XX

R8001XX

R8005 XX

R8004 XX

R8011 XX

R8031 XX

R8037

XX

R8026 XX

R8025 XX

R8024 XX

R8023 XX

R8022 XX

R8038 XX

R8021 XX

R8019 XX

R8016 XX

R8017 XX

R8015 XX

R8018 XX

GND

S8001

1 2

3 4

CL8002

CL8003

CL8001

CN8002 51P

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

D8001

EDZ-TE61-5.6B

CN8001

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51525354

36

CN800314P

1

2

3

4

5

6

7

8

9

10

11

12

13

14

CN8004 14P

1

2

3

4

5

6

7

8

9

10

11

12

13

14

xCD2

D10

D08

A00

IORDY

A05

INTRQ

A09

xCS1

D06

D11

GND

D02

xDASP

Vcc

A02

xVS2

A08

Vcc

xVS1

xIORW

D07

D12

A10

GND

D14

D04

xIOIS16

GND

xPDIAG

D09

A01

D00

xRESET

xINPACK

A06

A04

xWE

xATA_SEL

D15

D05

D01

xCD1

xREG

A03

xCSEL

A07

xIORD

xCS0

D13

D03

GND(xCD2)

D10

D08

A00

IORDY

GND(A05)

INTRQ

GND(A09)

xCS1

D06

D11

COVER_STAT

D02

xDASP

D05

Vcc

D01

A02

xCD

xREG

GND(xVS2)

GND(A03)

GND(A08)

GND(xCSEL)

Vcc

GND(A07)

GND(xVS1)

xIORD

xIORW

xCS0

D07

D13

D03

D12

GND(A10)

GND

D14

D04

GND(xIOIS16)

xPDIAG

D09

A01

D00

xRESET

xINPACK

Vcc(A06)

GND(A04)

GND(xWE)

xATA_SEL

D15

GND

SCL

GND

3.0V

GND

SDA

GND

A0

GND

CS

GND

RES

GND

ENA

GND

SCL

GND

3.0V

GND

SDA

GND

A0

GND

CS

GND

RES

GND

ENA

COVEROPEN/CLOSE

XX MARK:NO MOUNT

CF CONNECTORCF-110 BOARD

FLASHCOMPACT

(1/5)

(Page 4-4)

TK-071

LC-095CN6002


Through the

(Page 4-10)

TK-071(4/5)CN2002


Through the

(Page 4-7)

FP-201Flexible

Through theCN4001

4-10HVR-MRC1

LC-095

NO MARK:REC/PB MODE

3

0

0

3

3.3

3

G

6 9

F

B

H

7 10

C

05

8 11

D

B

G

12

E E

H

1

A

4

D

A

2

C

5

F

SCL

SDA

A0

#CS

#RES

ENA

C60031u C

16V

C601210u

C

C60111u C

C60070.1u B

C60060.1u B

C60130.1u

B

C60050.1u B

10V

C60040.1u B

10V

C60081u C

C60091u C

C60101u C

CL6005

CL6006

CL6002

CL6001

CL6004

CL6003

ND6001

2 VDD1

3 P/S

4 C86

5 VSS2

6 CLS

7 M/S

8 VDD2

9 VR

10 V5

11 V4

12 V3

13 V2

14 V1

15 VDD3

16 VSS3

17 C2+

18 C2-

19 C1+

20 C1-

21 C3-

22 VOUT

23 VSS4

24 VSS5

25 VDD4

26 D7

27 D6

28 D5

29 D4

30 D3

31 D2

32 D1

33 D0

34 VDD5

35 RD

36 WR

37 VSS6

38 A0

1 VSS

39 RES

40 VDD6

41 CS2

42 CS1

43 VSS7

44 DOF

45 CL

46 FR

47 FRS

48 OSC2

49 OSC1

R6014 33k

R6019 33k

R6020 33k

R6015 33k

R6013 33k

R6017 33k

R6022 33k

R6011 33k

R6012 33k

R6007300k

R6008390

R6009150k

R6010510k

R6016 33k

R6021 33k

R6018 33k

R6023 33k

Q6002RTF015P02TL

C6002

1u

C6001

0.1u B

R6001

XX

R6004

470

R6005

470

FB6001

R6003

XX

D6001CL-271TLY-C-TS

D6002CL-271TLY-C-TS

R602433k

Q6001DTC144EMT2L

CL6030

CN6002 14P

1

2

3

4

5

6

7

8

9

10

11

12

13

14

LCD

A0

GND

GND

CS

3.0V

SCL

GND

GND

GND

ENA

GND

GND

SDA

RES



XX MARK:NO MOUNT

LCDLC-095 BOARD

CF-110CN8003


Through the

(Page 4-9)

4-11HVR-MRC1

SW-525

NO MARK:REC/PB MODE R:REC MODE P:PB MODE

3.3

R0/P3.3

R3.3/P0

,

,

STOP

PLAY

EXEC

z

H >.

s

3

G

6 9

F

B

H

7 10

C

05

8 11

D

B

G

12

E E

H

1

A

4

D

A

2

C

5

F

C70

010.

01u

B25

V

C70

040.

01u

B25

V

C70

070.

01u

B25

V

C70

020.

01u

B25

V

C70

050.

01u

B25

V

C70

080.

01u

B25

V

C70

060.

01u

B25

V

C70

030.

01u

B25

V

R7001330

D7009CL-196HR-CD-T

CN7001 20P

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

Q7001DTA144EMT2L

S7010

D70

05ED

Z-TE

61-5

.6B

D70

01

EDZ-

TE61

-5.6

B

D70

07ED

Z-TE

61-5

.6B

D70

08ED

Z-TE

61-5

.6B

D70

06ED

Z-TE

61-5

.6B

D70

03

EDZ-

TE61

-5.6

B

D70

02

EDZ-

TE61

-5.6

B

D70

04ED

Z-TE

61-5

.6B

D70

11X

X

S70

03

S70

09

S70

02

S70

07

S70

06S

7005

S70

01

S70

04

S70

08

REPEAT

POWERLED DRIVE

FF

LED_ON

GND

REPEAT

GND

MENU

GND

GND

CAM_LINK

GND

GND

GND

3.3V

SW_OFF_CN

GND

REW

STOP

PLAY

REC_ON

SW_PWR

MENUCAM LINK

OFFON T

REC

XX MARK:NO MOUNT

CONTROL SWITCHSW-525 BOARD

REC LAMP,CF ACCESS

42

1 3

42

1 3

42

1 3

42

1 3

42

1 3

42

1 3

42

1 3

42

1 3

42

1 3

4 3 2 156

78

TK-071(4/5)CN2001


Through the

(Page 4-7)

4-12HVR-MRC1

FP-202, FP-203

(PRINTED WIRING BOARD is omitted)

Note: CN902 (HOT SHOE) is not included in FP-202 flexible board.

A

D

3

F

C

2

E

B

1

E

B

D

F

A

C

05

4

ACV_UNREG

N.C

DETECT

REG_GND

N.C

REG_GND

TPB+

TPB-

REG_GND

TPA+

TPA-

N.C

UNREG

N.C

REG_GND

REG_GND

REG_GND

REG_GND

REG_GND

UNREG

UNREG

ACV_UNREG

LND106

LND107

LND108

LND109

LND110

LND116

LND115

LND114

LND113

LND112

LND111

LND101

LND102

LND103

LND104

LND105

TPA-

TPA+

REG_GND

TPB-

TPB+

REG_GND

REG_GND

ACV_UNREG

REG_GND

REG_GND

REG_GND

UNREG

ACV_UNREG

DETECT

LND010

LND007

LND005

LND013

LND012

LND004

LND014

LND015

LND016

LND017

LND018

LND019

LND020

LND008

LND003

LND002

LND001

LND006

LND009

LND011

HOT SHOE (MEMORY RECORDING UNIT)FP-202 FLEXIBLE BOARD

HOTSHOE

CN902

1Pin1Pin

20Pin

16Pin

TK-071(1/5)CN4002

(Page 4-4)

(PRINTED WIRING BOARD is omitted)

Note: CN903 (HOT SHOE) is not included in FP-203 flexible board.

A

D

3

F

C

2

E

B

1

E

B

D

F

A

C

05

4

ACV_UNREG

N.C

DETECT

REG_GND

N.C

REG_GND

TPB+

TPB-

REG_GND

TPA+

TPA-

N.C

UNREG

N.C

REG_GND

REG_GND

REG_GND

REG_GND

REG_GND

UNREG

UNREG

ACV_UNREG

LND026

LND027

LND028

LND029

LND030

LND036

LND035

LND034

LND033

LND032

LND031

LND021

LND022

LND023

LND024

LND025

TPA-

TPA+

REG_GND

TPB-

TPB+

REG_GND

REG_GND

ACV_UNREG

REG_GND

REG_GND

REG_GND

UNREG

ACV_UNREG

DETECT

LND010

LND007

LND005

LND013

LND012

LND004

LND014

LND015

LND016

LND017

LND018

LND019

LND020

LND008

LND003

LND002

LND001

LND006

LND009

LND011

HOT SHOE (i.LINK CRADLE)FP-203 FLEXIBLE BOARD

HOTSHOE

CN903

1Pin1Pin

20Pin

16Pin

CR-090CN9005

(Page 4-13)

4-13HVR-MRC1

CR-090

Note:BT901 and J901 are not includedin CR-090 complete board.

265 1 HDV/DV

3

G

6 9

F

B

H

7 10

C

05

8 11

D

B

G

12

E E

H

1

A

4

D

A

2

C

5

F

RB900101 2

3 45 67 8

TH9001

TH9002

TH9003

TH9004

LD9001

LD9002R9002

0

R90030

C90040.01uB

C90030.01uB

FB9001

C9002

1u B

10V

C9001

1u B

10V C90050.01uB

F9001

F9002 (1.4A/32V)

(1.4A/32V)

C90060.01uB

CL9002

CL9001

C9007XX

CN9004

1

2

3

4

5

6

7

89

CN9001 4P

1BATT(+)

2SW

3SIG

4BATT(-)

CN9002 3P

1PLUS

2MINUS_A

3MINUS_B

LF900112

3 4

D9002MAZS120008SO

D9001MAZS120008SO

CN

9005

20P

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

VP

VG

TPB-

TPB+

TPA-

TPA+

CHASSIS_GND

CHASSIS_GND

REG

_GN

D

REG

_GN

D

REG

_GN

D

REG

_GN

D

N.C

UN

REG

UN

REG

AC

V_U

NR

EG

AC

V_U

NR

EG

N.C

DET

ECT

REG

_GN

D

REG

_GN

D

TPB

+

TPB

-

TPA

-

TPA

+

REG

_GN

D

REG

_GN

D

REG

_GN

D

−

+

BT901BATTERY

TERMINAL

DC INJ901

S

XX MARK:NO MOUNT

DC IN, HDV/DV CONNECTORCR-090 BOARD

FLEXIBLE

(Page 4-12)

FP-203

LND001 – LND020

• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.

4-3. PRINTED WIRING BOARDS

HVR-MRC1

LinkLink

CF-110 BOARD

TK-071 BOARD

LC-095 BOARD

CR-090 BOARD

SW-525 BOARD

COMMON NOTE FOR PRINTED WIRING BOARDS

4-14HVR-MRC1

4-3. PRINTED WIRING BOARDS4-3. PRINTED WIRING BOARDS

• : Uses unleaded solder.• : Circuit board

: Flexible boardPattern from the side which enables seeing.

: pattern of the rear side(The other layers’ patterns are not indicated)

• Through hole is omitted.• There are a few cases that the part printed on diagram

isn’t mounted in this model.• C: panel designation

(ENGLISH)THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS

4-3. PRINTED WIRING BOARDS

(JAPANESE)

2 1

3

2 1

3

2 1

3

345

21

123

654

EB

C

31

5

2

46

123

654

31

5

2

46

123

54

4 3

1 2

31 2

45

53 4

12

14

23

46

2

5

31

12

43

14

23

• Chip parts.Transistor Diode

プリント図共通ノート【プリント図ノート】・：無鉛半田を使用しています。・：基板

：フレキシブル配線板見ている面側のパターン。

：裏側のパターン（他のパターンについては表示されていません）

・スルーホールは省略。・プリント図には，本機で使用していない部品が記載されている場合があります。

・Cはパネル表示名称。

4-15HVR-MRC1

TK-071 (6 layers)

: Uses unleaded solder.

TK-071

15 4

3

58

5 8

20

1

48

112

13

37

36

24

25

120

18

45

FB10

01

FB1004

FB1005

C400

5

CL50

01

CL5002

CL5003

CL5004

CL5005

CL5006CL5007

CL5008CL5009CL5010CL5011 CL

5012

CL50

13

CL50

14

CL50

15CL

5016

CL50

17

CL50

18CL

5019

L1001

L1002

JL50

01JL

5002

JL50

03JL

5004

JL50

05

JL50

06

IC4002

JL50

07

JL50

08JL

5009

JL50

10JL

5011

CL50

43C500

4C500

3

R4042

R40

43

R40

44 R4045

R40

46

R4048

C501

0

R40

49

C5011

C5013

C5016

C501

8

C501

9

D00

1

C502

0

C502

1

C5024

C502

5

C5026

C502

7

C5028

C502

9

R5001

R5002

R5003

R5004

R5005

R50

06R

5007

C503

0

R50

08

R4069

C5031

R50

09

IC5001

C503

2

C5033

C5034

R40

70

R50

10

R40

71

R50

11R

5012

R50

13

R50

14R

5015

R50

16

R50

17

R50

18

R50

19

R50

20

R50

21

R50

22

R50

23

R50

25

R50

26

R5027

R5028

R50

29

R50

30

R50

31

R50

32

R50

33

R50

34

R5035

R5036

R5037

R5038

R5039

R5040

R5041

R50

46

C100

1C1

002

C100

4C1

005

C100

6

C101

3

C100

7

Q1004

Q1005

CL2012

C1028

C1030

C1031

C1029

D10

05

JL20

02

JL20

03JL

2004

JL20

05

C1032

JL20

06

C1033

JL20

08

R1023

R1024

R1025

R1026

CN20

01

C2001

C2002

C2003

C200

4

C2005

C200

6

C2007

C2008

C2009

R1042

F1001

F1002

C2010

C2011

C2012

C2013

C2016

C2017

C2018

C201

9

C202

0

R2001

R2002

R2003

R2004

R2005

X5001

R2006

R2007

R2008

R2009

IC2001

R2010

R2011

R2012

R2013

R2014

R2015

R2016

R2017

R2018

R2019

R2020 R20

21

R20

22

FB50

02

FB50

03

FB5004

FB5005

LF40

01

FB50

06

R2026

R2028

R2031

R2053

CN4002

IC5002

14

1 4

A1 B1 C1 D1 E1 F1 G1 H1 J1 K1 L1 M1 N1 P1 R1 T1 U1 V1 W1 Y1




A5 B5 C5 D5 U5 V5 W5 Y5

A6 B6 C6 D6 U6 V6 W6 Y6

A7 B7 C7 D7 U7 V7 W7 Y7

A8 B8 C8 D8 U8 V8 W8 Y8

A9 B9 C9 D9 J9 K9 L9 M9 U9 V9 W9 Y9

A10 B10 C10 D10 J10 K10 L10 M10 U10 V10 W10Y10

A11 B11 C11 D11 J11 K11 L11 M11 U11 V11 W11Y11

A12 B12 C12 D12 J12 K12 L12 M12 U12 V12 W12Y12

A13 B13 C13 D13 U13 V13 W13Y13

A14 B14 C14 D14 U14 V14 W14Y14

A15 B15 C15 D15 U15 V15 W15Y15

A16 B16 C16 D16 U16 V16 W16Y16

A17 B17 C17 D17 E17 F17 G17 H17 J17 K17 L17 M17 N17 P17 R17 T17 U17 V17 W17Y17




13 4

5

1 584

TK-071 BOARD (SIDE A)

12

34

11

05

1-874-877-

M3.3VA

A1.8V

M_3.3V

64 17

161

49 32

3348

65

C

BE

C

BE

CC

BB

EE

D

GS

C

CC

B

BB

E

EE

C

B E

8 1

24172516

329

33

1 2 345

13 4

5

13 4

5

114

154

3

1 543

154

3

25

0

15

1

FB1002

FB10

03

C4001

FB1006

C400

2

C400

3

FB10

07

FB1008

FB10

09

C400

6

C4007

C4008

C400

9

FB1010

C4010

C4011

C401

2

C4013

C401

4

C401

5

C401

6

C4017 C401

8

C401

9

R4001

R4002 R4003

R4004 R4005

R4006 R4007

R4008 R4009

IC4003

R4010 R4011

R4012 R4013

R4015

R4016R4018

R4019

R4020

R4021

R4022

R4023

R4024

R4025

R4026

R4027

R4028

R4029R4030

R4031 R4032

R4033

R4034

R4035

FB2001

R4036

R4037

R4038

R4039

C500

1

C500

2

C500

5

C5006

C5007

R4040

C5008

C500

9

R4047

C501

2

C501

4

C501

5

C5017

R4050

R4051

R4052

R4053

R4054

R4055

R4056

R4057R4058

R4059

CL10

01

C502

2

CL10

02

C502

3

R4060

R4061

R40

62

R40

63

R4064

R4065

R40

66

R4067

R4068

FL40

01

FL40

02

FL4003 R40

72

R40

73

R5024

FB30

01

Q10

01Q

1002

Q10

03

C1008C1009

Q10

06

Q10

07

Q10

08Q

1009

C1010

CL2004

C1011

C101

4

Q10

10

C101

5

Q10

11

C101

6

Q10

12

C1017

Q10

13

C1018

Q1014

C1019

Q1015

D

D

G

G

S

S

Q10

16

Q1017

Q1018

C102

0C1

021

C1022

C102

3

C102

4C1

025

D1001

C1026

D1002

C1027

D10

03A

AK KA

AK

KD

1004

R1001

R1002

R1045

D1006

R1003

R1004

R10

05

JL20

01

X400

1

R10

06

R10

07

R10

08

R10

09

IC1001

CL2026

IC1002

JL2007

IC1003

C1034

IC10

04IC

1005

C1038

R1010

C1039

C1036

R1011

R1012

R10

13

R10

14

R10

15R

1016

R10

17

C104

0

R10

18

C104

1

R1019

C104

2

C104

3C1

044

C1045

C104

6

R10

44

R10

43

C103

5

C100

3

C101

2

C103

7

C1047

C104

8

R10

20

C1049

R10

21

FB40

01

R1022

FB40

02

FB4003

FB40

04

CL2041

FB4005

CL2042

FB40

06

R1027

R1028

R1029

CN20

02

R1030

R1031

R1032

R10

33

R10

34

R1035

R1036

R1037

R1038 R1039

R10

40

R1041

CL3003

C2022

C202

3

C2024

IC2003

IC20

04

IC2005

FB50

01R2023

R20

27

R2032

R2033

R2034

R2035

R20

36R

2037

R20

38

R2039

C3001

C3002C3003

C3004

C300

5

C300

6C3

007

R2040

C300

8

R2041

C3009

R20

42

R2043

R2044

R20

45

R2046

R20

47

R20

48

C301

0

CL40

04

R2049

C3011

C3012

C301

3C3

014

C3015

R20

50

R20

55

R20

56

R2057R2058

R2059

R3001

R20

61

R3002

R20

62

R20

63

R20

64

R2065

IC30

01

CN40

01

13 4

6

13 4

6

13 4

6

111-874-877-

A1

A2

A3

B1

B2

B3

C1

C2

C3

D1

D2

D3

E1

E2

E3

F1 F2 F3

G1

G2

G3

H1

H2

H3

J1 J2 J3

K1

K2

K3

L1

L2

L3

M1

M2

M3

N1

N2

N3

P1

P2

P3

R1

R2

R3

A7

A8

A9

B7

B8

B9

C7

C8

C9

D7

D8

D9

E7

E8

E9

F7 F8 F9

G7

G8

G9

H7

H8

H9

J7 J8 J9

K7

K8

K9

L7

L8

L9

M7

M8

M9

N7

N8

N9

P7

P8

P9

R7

R8

R9

13

42

31

6 42

4

3

1

2

4 3

1

2

4 3

1

TK-071 BOARD (SIDE B)

05

31

6 4

31

6 4

M3.3V

1.8V

4-16HVR-MRC1

CF-110 (6 layers)


CF-110

S8001

CF-110 BOARD (SIDE A)

11

05

1-874-878-

1

2

3

4 COVEROPEN/CLOSE

250

151

114

114

CL8001

CL8002

CL8003

CN8003

CN80

04CN

8002

C8001

D8001

R8001R8002

R8003R8004

R8005R8006

R8007R8008

R8009R8010

R8011R8012

R8013

R8015R8016

R8017

R8018

R8019

R8021

R8022R8023

R8024R8025

R8026R8027

R8028R8029

R8030R8031

R8032R8033

R8034

R8036R8037

R8038

1

26

225 4

950

51

53

54

CN80

01

52

1105 1-874-878-

CF-110 BOARD (SIDE B)

COMPACTFLASH

Note: CN8001 is not supplied, but this is included in CF-110 complete board.

4-17HVR-MRC1

LC-095 (6 layers), SW-525 (6 layers)


LC-095, SW-525

D60

01D

6002

KA

KA

LC-095 BOARD(SIDE A)

1105 1-874-879-

ND6001LCD

1 49D6001, D6002(BACKLIGHT)

1 14

C G

S

D

BE

CL6001

CL6002

CL6003

CL6004

CL6005

CL6006

CL6030

CN6002

C6001

C6002

C6003

C600

4

Q6001

C600

5

C600

6

Q60

02

C600

7

C600

8

C600

9

C601

0

C601

1

C6013

C6012

R6001

R6003 R6004

R6005

R60

07R

6008

R60

09R

6010

R60

11

R60

12

R60

13

R60

14

R6015

R6016

R6017

R6018

R6019

R6020

R6021

R6022

R6023

R60

24

FB6001

LC-095 BOARD (SIDE B)

1105 1-874-879-

120

C

BE

CN70

01

C7001

C7002

C7003

C7004

Q7001

C7005

C7006

C7007

C7008

D7001

D7002

D7003

D7004

R700

1

D7005

D7006

D7007

D7008

D7011

S7001

S7002

S7003

S7004

S7005

S7006

S7007

S7008

S7009

S7010

4 2

13

4 2

13

4 2

13

4 2

13

4 2

13

4 2

13

4

A

05

K

2

13

4 2

13

4 2

13

1 45

6

7

8

CAM LINK MENU REPEAT

SW-525 BOARD

111-874-880-

POWER

OFF ONT

D7009

STOPs

z

REC

,

>PLAYEXEC

H

,

>

REC LAMP,CF ACCESS

HVR-MRC14-18E

CR-090 (6 layers)


CR-090

1 4 1 3

120

D9001

D9002 F9002

TH90

01

TH90

02

TH90

03

TH90

04

RB9001

FB90

01

F900

1

LF9001

CL9001 CL9002

CN9001CN9002

C9001 C9002

C9003 C9004

C9005 C9006

CN9005

CR-090 BOARD (SIDE A)

1105 1-874-881-

1 72 8

1 4

32

R9002

R9003

LD9001

LD9002

C9007

1 2

5 68 9

7

3 4

CN9004

HDV/DV

1105 1-874-881-

CR-090 BOARD (SIDE B)

5. REPAIR PARTS LIST

NOTE

HVR-MRC1

NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.

BASE CABINET SECTION MAIN CABINET SECTION ADAPTOR SECTION

A B C

ACCESSORIESLinkLink ELECTRICAL PARTS LISTELECTRICAL PARTS LIST

CR-090 BOARD

CF-110 BOARD

SW-525 BOARD

LC-095 BOARD TK-071 BOARD

C

B

B

B A

LinkLink EXPLODED VIEWSEXPLODED VIEWS

5. REPAIR PARTS LIST

5-1

5. REPAIR PARTS LIST5. REPAIR PARTS LIST

HVR-MRC1

(ENGLISH)NOTE:• -XX, -X mean standardized parts, so they may have some differences from

the original one.• Items marked “*” are not stocked since they are seldom required for routine

service. Some delay should be anticipated when ordering these items.• The mechanical parts with no reference number in the exploded views are not

supplied.• Due to standardization, replacements in the parts list may be different from

the parts specified in the diagrams or the components used on the set.• CAPACITORS:

uF: µF• COILS

uH: µH• RESISTORS

All resistors are in ohms.METAL: metal-film resistorMETAL OXIDE: Metal Oxide-film resistorF: nonflammable

• SEMICONDUCTORSIn each case, u: µ, for example:uA...: µA... , uPA... , µPA... ,uPB... , µPB... , uPC... , µPC... ,uPD..., µPD...

When indicating parts by reference number,please include the board name.

(JAPANESE)

The components identified by mark 0 ordotted line with mark 0 are critical for safety.Replace only with part number specified.

Les composants identifiés par une marque0 sont critiques pour la sécurité.Ne les remplacer que par une pièce portantle numéro spécifié.

【使用上の注意】• ここに記載されている部品は, 補修用部品であるため, 回路図及びセットに付いている部品と異なる場合があります。

• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合があります。

• *印の部品は常備在庫しておりません。• コンデンサの単位でuFはμFを示します。• 抵抗の単位Ωは省略してあります。金　　被：金属被膜抵抗。サンキン：酸化金属被膜抵抗。

• インダクタの単位でuHはμHを示します。• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμA..., μPA..., μPB..., μPC..., μPD...を示します。

0印の部品，または0印付の点線で囲まれた部品は，安全性を維持するために，重要な部品です。従って交換時は，必ず指定の部品を使用してください。

図面番号で部品を指定するときは基板名又はブロックを併せて指定してください。

お願い

• Color Indication of Appearance PartsExample:(SILVER) : Cabinet’s Color(Silver) : Parts Color

• 外装部品色表示例：(SILVER):セットの色を表す。(Silver) : 部品の色を表す。

• AbbreviationAR : Argentine modelAUS : Australian modelBR : Brazilian modelCH : Chinese modelCND : Canadian modelEE : East European modelHK : Hong Kong modelJ : Japanese modelJE : Tourist modelKR : Korea modelNE : North European model

5-2


HVR-MRC1

DISASSEMBLY HARDWARE LIST

Ref. No. Part No. Description Ref. No. Part No. Description

* 1 3-295-565-01 LABEL (J), CF CAUTION (J)* 1 3-295-566-01 LABEL (U), CF CAUTION (US, CND, AEP, E)* 1 3-295-567-01 LABEL (CN), CF CAUTION (CH)

2 1-965-666-11 FP-201 FLEXIBLE BOARD3 1-835-017-11 FLEXIBLE FLAT CABLE (FFC-159)

4 A-1498-040-A TK-071 BOARD, COMPLETE (SERVICE)5 3-290-970-01 SHEET, RADIATION6 X-2188-921-1 HEAT SINK ASSY, CF

* 7 3-290-971-01 SHEET (FP202)

8 1-965-667-11 FP-202 FLEXIBLE BOARD

9 X-2188-922-1 CABINET ASSY, CF BASE* 10 3-290-945-01 LABEL, FUSE REPLACEMENT* 11 (Note) SERVICE (HVR-MRC1 MAIN)

CN902 1-818-891-31 CONNECTOR, EXTERNAL (HOT SHOE)#46 2-660-401-11 SCREW (M1.7), NEW TRU-STAR, P2 (Red)

#53 3-080-206-21 SCREW, TAPPING, P2 (Black)

5-1-1. BASE CABINET SECTION

ns: not supplied

5-1. EXPLODED VIEWS

#46

ns

#53

#53

CN902

Main Cabinet Section(See page 5-3)

ns

2 3

45

6

7

89

1

11(Note)

10

Ver. 1.2 2009.03The changed portions fromVer. 1.1 are shown in blue.

Note: There are differences in the label indication ineach country/area.Use the correct part for the each camera or model.(See the chart below)

Note: 仕向によりラベル表示に相違があります。下表を参照してカメラ本体の機種名・仕向に合った部品を使用してください。

Main ModelPart No.Description

HVR-Z7J* A-1700-861-AHVR-S270JSERVICE (HVR-MRC1 MAIN J)HVR-MRC1K (J)

HVR-Z7U* A-1700-862-AHVR-S270USERVICE (HVR-MRC1 MAIN U)HVR-MRC1K (US, CND)

HVR-Z7N * A-1700-863-AHVR-S270N SERVICE (HVR-MRC1 MAIN N)

HVR-Z7PHVR-S270P * A-1700-864-A

HVR-Z7E SERVICE (HVR-MRC1 MAIN EP)HVR-S270E

HVR-MRC1K (AEP)* A-1700-865-ASERVICE (HVR-MRC1 MAIN KCE)

HVR-Z7C* A-1700-866-AHVR-S270CSERVICE (HVR-MRC1 MAIN C)HVR-MRC1K (CH)

5-3


HVR-MRC1

HARDWARE LIST


51 X-2188-920-1 DOOR ASSY, CF52 X-2188-919-1 LOCK ASSY, DOOR53 A-1490-529-A SW-525 BOARD, COMPLETE54 1-835-016-11 FLEXIBLE FLAT CABLE (FFC-157)55 X-2188-918-1 FRAME ASSY, DOOR

56 X-2188-823-1 FRAME ASSY, CF MAIN57 A-1490-526-A CF-110 BOARD, COMPLETE58 1-835-017-11 FLEXIBLE FLAT CABLE (FFC-159)59 A-1544-473-A LC-095 BOARD, COMPLETE (SERVICE)60 3-290-930-01 HOLDER, LCD

* 61 3-290-929-01 SHEET, CF REFLECTION* 62 3-290-927-01 LIGHT, GUIDE

* 63 3-290-928-01 SHEET, CF DIFFUSION* 64 3-290-926-01 FRAME, CF LCD GROUND

65 3-288-253-01 CABINET, CF MAIN

66 3-290-968-01 WINDOW, LCD67 3-295-564-01 LABEL, CF

* 68 2-891-483-01 TAPE, LCD69 3-296-530-01 SHEET (H)

* 70 3-290-969-01 FRAME (UPPER), CF DOOR GROUND

* 71 2-697-881-01 DAMPER, LCD#2 2-635-562-31 SCREW (M1.7) (Black)#11 3-078-890-11 SCREW, TAPPING (Silver)#46 2-660-401-11 SCREW (M1.7), NEW TRU-STAR, P2 (Red)

5-1-2. MAIN CABINET SECTION

ns: not supplied

SW-525

CF-110

A

A

ns

#11

#11 #11

#11#11

#46

#46

ns

51

5354

55

56

57

58

59

70

6068

61

62

63

64

7165

6667

52

#2

69

DISASSEMBLY


5-4


HVR-MRC1

5-1-3. ADAPTOR SECTION

ns: not supplied

DISASSEMBLY HARDWARE LIST


101 3-288-257-01 CABINET (CF)102 A-1490-527-A CR-090 BOARD, COMPLETE103 1-965-668-11 FP-203 FLEXIBLE BOARD

* 104 3-290-984-01 PLATE, SHOE RETAINER* 105 3-290-981-01 RETAINER, TERMINAL

106 3-290-980-01 HOLDER, DC-IN* 107 3-290-985-01 PLATE, TRIPOD RETAINER

108 3-290-986-01 GUIDE, TRIPOD109 2-664-982-01 SCREW, TRIPOD110 X-2188-923-1 CABINET (BATT) ASSY

111 2-697-897-01 COVER, DC-IN

112 2-890-916-01 CLAMP, CABLE* 113 3-290-982-01 PLATE (L), GROUND* 114 3-290-983-01 PLATE (R), GROUND0BT901 1-694-411-31 TERMINAL BOARD, BATTERY

CN903 1-818-890-21 CONNECTOR, EXTERNAL (HOT SHOE)0J901 1-785-247-31 CONNECTOR, DC-IN

#1 2-635-562-11 SCREW (M1.7) (Black)#2 2-635-562-31 SCREW (M1.7) (Black)#12 3-080-204-21 SCREW, TAPPING, P2 (Black)

#53 3-080-206-21 SCREW, TAPPING, P2 (Black)

ns

BT901

J901

CN903

#12

#2#2

#53

#12

#1

#1

#12

#12#12

#12

101

102

103

104

105106

114

113

107

108 109

111

112

110

• Refer to page 5-1 for mark 0.


5-5

Ref. No. Part No. Description Ref. No. Part No. Description5-2. ELECTRICAL PARTS LIST

HVR-MRC1

A-1490-526-A CF-110 BOARD, COMPLETE**********************

(CN8001 is not supplied, but this is included inCF-110 complete board.)

< CAPACITOR >

C8001 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V

< CONNECTOR >

CN8001 (Not supplied) CONNECTOR, CF CARD* CN8002 1-820-857-81 CONNECTOR, FPC (ZIF) 51P* CN8003 1-820-336-71 CONNECTOR, FFC/FPC (ZIF) 14P* CN8004 1-820-336-71 CONNECTOR, FFC/FPC (ZIF) 14P

< DIODE >

D8001 8-719-074-67 DIODE EDZ-TE61-5.6B

< SWITCH >

S8001 1-786-148-11 SWITCH, PUSH (1 KEY) (COVER OPEN/CLOSE)

A-1490-527-A CR-090 BOARD, COMPLETE**********************

< CAPACITOR >

C9001 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC9002 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC9003 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC9004 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC9005 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V

C9006 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V

< CONNECTOR >

CN9001 1-580-057-11 PIN, CONNECTOR (SMD) 4PCN9002 1-580-056-21 PIN, CONNECTOR (SMD) 3PCN9004 1-817-382-11 CONNECTOR, I-LINK (6P) (HDV/DV)CN9005 1-816-648-61 FFC/FPC CONNECTOR (LIF) 20P

< DIODE >

* D9001 6-501-961-01 DIODE MAZS120G08S0* D9002 6-501-961-01 DIODE MAZS120G08S0

< FUSE >

0F9001 1-576-406-11 FUSE, MICRO (1608) (1.4A/32V)0F9002 1-576-406-11 FUSE, MICRO (1608) (1.4A/32V)

< FERRITE BEAD >

* FB9001 1-481-196-21 FERRITE, EMI (SMD) (3216)

< LINE FILTER >

* LF9001 1-457-217-21 COMMON MODE CHOKE COIL

< RESISTOR >

R9002 1-216-864-11 SHORT CHIP 0R9003 1-216-864-11 SHORT CHIP 0

< COMPOSITION CIRCUIT BLOCK >

RB9001 1-234-400-21 CONDUCTOR, NETWORK (1005X4)

< THERMISTOR >

TH9001 1-805-726-11 THERMISTOR, POSITIVETH9002 1-805-726-11 THERMISTOR, POSITIVETH9003 1-805-726-11 THERMISTOR, POSITIVETH9004 1-805-726-11 THERMISTOR, POSITIVE

A-1544-473-A LC-095 BOARD, COMPLETE (SERVICE)**********************

< CAPACITOR >

C6001 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC6002 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3VC6003 1-100-352-91 CERAMIC CHIP 1uF 20% 16VC6004 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC6005 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V

C6006 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC6007 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC6008 1-100-352-91 CERAMIC CHIP 1uF 20% 16VC6009 1-100-352-91 CERAMIC CHIP 1uF 20% 16VC6010 1-100-352-91 CERAMIC CHIP 1uF 20% 16V

C6011 1-100-352-91 CERAMIC CHIP 1uF 20% 16VC6012 1-100-966-91 CERAMIC CHIP 10uF 20% 10VC6013 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V

< CONNECTOR >

* CN6002 1-820-336-71 CONNECTOR, FFC/FPC (ZIF) 14P

< DIODE >

* D6001 6-501-573-01 DIODE CL-271TLY-C-TS (BACKLIGHT)* D6002 6-501-573-01 DIODE CL-271TLY-C-TS (BACKLIGHT)

< FERRITE BEAD >

FB6001 1-400-794-21 EMI FERRITE (SMD) (1608)

< LIQUID CRYSTAL DISPLAY >

ND6001 1-805-549-11 DISPLAY PANEL, LIQUID CRYSTAL

< TRANSISTOR >

Q6001 6-550-119-01 TRANSISTOR DTC144EMFS6T2LQ6002 6-551-067-01 TRANSISTOR RTF015P02TL

< RESISTOR >

R6004 1-218-839-11 METAL CHIP 470 0.5% 1/10WR6005 1-218-839-11 METAL CHIP 470 0.5% 1/10WR6007 1-208-946-81 METAL CHIP 300K 0.5% 1/16WR6008 1-218-948-11 RES-CHIP 390 5% 1/16WR6009 1-208-939-11 METAL CHIP 150K 0.5% 1/16W

R6010 1-208-952-81 METAL CHIP 510K 0.5% 1/16WR6011 1-218-971-11 RES-CHIP 33K 5% 1/16WR6012 1-218-971-11 RES-CHIP 33K 5% 1/16WR6013 1-218-971-11 RES-CHIP 33K 5% 1/16W

CF-110 CR-090 LC-095



5-6


HVR-MRC1

R6014 1-218-971-11 RES-CHIP 33K 5% 1/16W

R6015 1-218-971-11 RES-CHIP 33K 5% 1/16WR6016 1-218-971-11 RES-CHIP 33K 5% 1/16WR6017 1-218-971-11 RES-CHIP 33K 5% 1/16WR6018 1-218-971-11 RES-CHIP 33K 5% 1/16WR6019 1-218-971-11 RES-CHIP 33K 5% 1/16W

R6020 1-218-971-11 RES-CHIP 33K 5% 1/16WR6021 1-218-971-11 RES-CHIP 33K 5% 1/16WR6022 1-218-971-11 RES-CHIP 33K 5% 1/16WR6023 1-218-971-11 RES-CHIP 33K 5% 1/16WR6024 1-208-923-11 METAL CHIP 33K 0.5% 1/16W

A-1490-529-A SW-525 BOARD, COMPLETE***********************

< CAPACITOR >

C7001 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC7002 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC7003 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC7004 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC7005 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V

C7006 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC7007 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC7008 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V

< CONNECTOR >

CN7001 1-816-648-61 FFC/FPC CONNECTOR (LIF) 20P

< DIODE >

D7001 8-719-074-67 DIODE EDZ-TE61-5.6BD7002 8-719-074-67 DIODE EDZ-TE61-5.6BD7003 8-719-074-67 DIODE EDZ-TE61-5.6BD7004 8-719-074-67 DIODE EDZ-TE61-5.6BD7005 8-719-074-67 DIODE EDZ-TE61-5.6B

D7006 8-719-074-67 DIODE EDZ-TE61-5.6BD7007 8-719-074-67 DIODE EDZ-TE61-5.6BD7008 8-719-074-67 DIODE EDZ-TE61-5.6BD7009 8-719-077-09 DIODE CL-196HR-CD-T

(REC LAMP, CF ACCESS)

< TRANSISTOR >

Q7001 6-550-239-01 TRANSISTOR DTA144EMFS6T2L

< RESISTOR >

R7001 1-208-671-11 METAL CHIP 330 0.5% 1/16W

< SWITCH >

S7001 1-771-844-21 SWITCH, TACTILE (CAM LINK)S7002 1-771-844-21 SWITCH, TACTILE (., EXEC M)S7003 1-771-844-21 SWITCH, TACTILE (s STOP)S7004 1-771-844-21 SWITCH, TACTILE (MENU)S7005 1-771-844-21 SWITCH, TACTILE (H PLAY, EXEC)

S7006 1-771-844-21 SWITCH, TACTILE (REC z)S7007 1-771-844-21 SWITCH, TACTILE (REPEAT)S7008 1-771-844-21 SWITCH, TACTILE (>, EXEC m)S7009 1-771-844-21 SWITCH, TACTILE (REC)

S7010 1-771-731-21 SWITCH, SLIDE (POWER (ON/OFF))

A-1498-040-A TK-071 BOARD, COMPLETE (SERVICE)**********************

(IC5002 is not supplied, but this is included inTK-071 complete board.)

< CAPACITOR >

C1001 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC1002 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC1003 1-100-966-91 CERAMIC CHIP 10uF 20% 10VC1004 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC1005 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V

C1006 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC1007 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC1008 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC1009 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC1010 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V

C1011 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC1012 1-100-966-91 CERAMIC CHIP 10uF 20% 10VC1013 1-100-966-91 CERAMIC CHIP 10uF 20% 10VC1014 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC1015 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V

C1016 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC1017 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V

* C1018 1-112-692-11 CERAMIC CHIP 1000PF 5% 50V* C1019 1-112-692-11 CERAMIC CHIP 1000PF 5% 50V

C1020 1-164-874-11 CERAMIC CHIP 100PF 5% 50V

C1021 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC1022 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC1023 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC1024 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC1025 1-165-908-11 CERAMIC CHIP 1uF 10% 10V

C1026 1-164-860-11 CERAMIC CHIP 27PF 5% 50VC1027 1-164-860-11 CERAMIC CHIP 27PF 5% 50V

* C1028 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V* C1029 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V

C1030 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V

C1031 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V* C1032 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V* C1033 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V

C1034 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC1035 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V

C1036 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3VC1037 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3VC1038 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC1039 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC1040 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V

C1041 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3VC1042 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC1043 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC1044 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC1045 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V

C1046 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3VC1047 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3VC1048 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3VC1049 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3VC2001 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V

LC-095 SW-525 TK-071Ver. 1.1 2008.06The changed portions fromVer. 1.0 are shown in blue.

5-7


HVR-MRC1



C2012 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC2013 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC2016 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC2017 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V

* C2018 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V

C2022 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC2023 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V

* C3001 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3VC3002 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC3003 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V



C3014 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC3015 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4001 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC4002 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4003 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V

C4005 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V* C4006 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V

C4007 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC4008 1-164-852-11 CERAMIC CHIP 12PF 5% 50VC4009 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V

C4010 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4011 1-164-852-11 CERAMIC CHIP 12PF 5% 50VC4012 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4013 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4014 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V

C4015 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V* C4016 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V

C4017 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4018 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3VC4019 1-164-933-11 CERAMIC CHIP 220PF 10% 50V

* C5001 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3VC5002 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3VC5003 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V

* C5004 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3VC5005 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V


C5008 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5009 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5010 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V



C5021 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5022 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5023 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5024 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V

* C5025 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V

C5026 1-164-933-11 CERAMIC CHIP 220PF 10% 50VC5028 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25VC5030 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5031 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5032 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V


< CONNECTOR >

* CN2001 1-818-516-71 CONNECTOR, FFC/FPC (ZIF) 20PCN2002 1-816-645-61 FFC/FPC CONNECTOR (LIF) 14P

* CN4001 1-820-857-81 CONNECTOR, FPC (ZIF) 51PCN4002 1-816-648-61 FFC/FPC CONNECTOR (LIF) 20P

< DIODE >

D001 6-500-750-01 DIODE NSAD500H-T1-A0D1001 6-501-272-01 DIODE RB520CS-30T2R0D1002 6-501-272-01 DIODE RB520CS-30T2R

D1003 6-501-124-01 DIODE RSX101VA-30TRD1004 6-501-124-01 DIODE RSX101VA-30TR

* D1005 6-501-961-01 DIODE MAZS120G08S0* D1006 6-501-961-01 DIODE MAZS120G08S0

< FUSE >

0F1001 1-576-406-11 FUSE, MICRO (1608) (1.4A/32V)0F1002 1-576-406-11 FUSE, MICRO (1608) (1.4A/32V)

< FERRITE BEAD >

* FB1001 1-481-196-21 FERRITE, EMI (SMD) (3216)FB1002 1-400-915-21 INDUCTOR (EMI FERRITE) (2012)FB1003 1-400-915-21 INDUCTOR (EMI FERRITE) (2012)FB1004 1-400-915-21 INDUCTOR (EMI FERRITE) (2012)FB1005 1-400-619-11 BEAD, FERRITE (CHIP) (1608)

FB1006 1-400-619-11 BEAD, FERRITE (CHIP) (1608)FB1007 1-400-619-11 BEAD, FERRITE (CHIP) (1608)FB1008 1-400-619-11 BEAD, FERRITE (CHIP) (1608)FB1009 1-400-331-11 FERRITE, EMI (SMD) (1005)FB1010 1-400-619-11 BEAD, FERRITE (CHIP) (1608)

FB2001 1-400-915-21 INDUCTOR (EMI FERRITE) (2012)

TK-071



5-8


HVR-MRC1

FB3001 1-400-915-21 INDUCTOR (EMI FERRITE) (2012)FB4001 1-400-915-21 INDUCTOR (EMI FERRITE) (2012)FB4002 1-400-915-21 INDUCTOR (EMI FERRITE) (2012)FB4003 1-400-331-11 FERRITE, EMI (SMD) (1005)

FB4004 1-400-619-11 BEAD, FERRITE (CHIP) (1608)FB4005 1-400-331-11 FERRITE, EMI (SMD) (1005)FB4006 1-400-915-21 INDUCTOR (EMI FERRITE) (2012)FB5001 1-400-915-21 INDUCTOR (EMI FERRITE) (2012)FB5002 1-400-915-21 INDUCTOR (EMI FERRITE) (2012)

FB5003 1-400-915-21 INDUCTOR (EMI FERRITE) (2012)FB5004 1-400-331-11 FERRITE, EMI (SMD) (1005)FB5005 1-400-331-11 FERRITE, EMI (SMD) (1005)FB5006 1-400-915-21 INDUCTOR (EMI FERRITE) (2012)

< FILTER >

FL4001 1-234-939-21 FILTER, EMI REMOVAL (SMD)FL4002 1-234-939-21 FILTER, EMI REMOVAL (SMD)FL4003 1-234-939-21 FILTER, EMI REMOVAL (SMD)

< IC >

0 IC1001 6-707-357-01 IC LTC3728LXCUH#TR-R5* IC1002 6-709-667-01 IC S-812C33BPI-C4NTFG

IC1003 6-704-257-01 IC TK11130CSCL-G* IC1004 6-710-663-01 IC BU4325FVE-TR* IC1005 6-710-663-01 IC BU4325FVE-TR

* IC2001 6-712-221-01 IC uPD78F0513GA (S)-8EU-E2-AIC2003 8-759-058-64 IC TC7S32FU (TE85R)IC2004 8-759-058-64 IC TC7S32FU (TE85R)

* IC3001 6-710-662-01 IC K4M513233C-DN75TIC4002 8-759-058-62 IC TC7S08FU (TE85R)

* IC4003 6-710-683-01 IC TSB41AB2PAPR* IC5001 6-712-220-01 IC IND60C32A

IC5002 (Not supplied) IC AT45DB081B-CNU (Note)IC5002 (Not supplied) IC AT45DB081D-SU (Note)

< COIL >

L1001 1-456-019-11 INDUCTOR 4.7uHL1002 1-456-019-11 INDUCTOR 4.7uH

< LINE FILTER >

LF4001 1-457-064-13 COMMON MODE CHOKE COIL

< TRANSISTOR >

Q1001 6-550-566-01 TRANSISTOR DTC115TMFS6T2LQ1002 6-550-566-01 TRANSISTOR DTC115TMFS6T2LQ1003 6-550-119-01 TRANSISTOR DTC144EMFS6T2L

0Q1004 6-709-438-01 TRANSISTOR FDS6986AS0Q1005 6-709-438-01 TRANSISTOR FDS6986AS

Q1006 8-729-928-34 TRANSISTOR DTA124EE-TLQ1007 6-551-346-01 TRANSISTOR LSK3541FS8T2LQ1008 6-550-354-01 TRANSISTOR RTQ035P02TRQ1009 6-550-354-01 TRANSISTOR RTQ035P02TRQ1010 6-550-566-01 TRANSISTOR DTC115TMFS6T2L

* Q1011 6-551-600-01 TRANSISTOR DTC115EETLQ1012 6-550-354-01 TRANSISTOR RTQ035P02TR

* Q1013 6-551-600-01 TRANSISTOR DTC115EETLQ1014 6-550-119-01 TRANSISTOR DTC144EMFS6T2LQ1015 6-551-067-01 TRANSISTOR RTF015P02TL

Q1016 6-551-067-01 TRANSISTOR RTF015P02TLQ1017 6-550-354-01 TRANSISTOR RTQ035P02TRQ1018 6-550-354-01 TRANSISTOR RTQ035P02TR

< RESISTOR >

R1001 1-218-981-91 RES-CHIP 220K 5% 1/16WR1002 1-218-974-11 RES-CHIP 56K 5% 1/16WR1003 1-218-974-11 RES-CHIP 56K 5% 1/16WR1004 1-208-635-11 METAL CHIP 10 0.5% 1/16WR1005 1-218-974-11 RES-CHIP 56K 5% 1/16W

R1006 1-208-713-11 METAL CHIP 18K 0.5% 1/16WR1007 1-218-978-11 RES-CHIP 120K 5% 1/16WR1008 1-208-928-11 METAL CHIP 51K 0.5% 1/16WR1009 1-208-696-11 METAL CHIP 3.6K 0.5% 1/16WR1010 1-208-893-11 METAL CHIP 1.8K 0.5% 1/16W

R1012 1-218-982-11 RES-CHIP 270K 5% 1/16WR1013 1-208-905-11 METAL CHIP 5.6K 0.5% 1/16WR1014 1-208-911-11 METAL CHIP 10K 0.5% 1/16WR1015 1-218-990-81 SHORT CHIP 0R1019 1-218-989-11 RES-CHIP 1M 5% 1/16W

R1021 1-218-990-81 SHORT CHIP 0* R1023 1-245-685-21 RES-CHIP 0.051 5% 1/8W* R1024 1-245-685-21 RES-CHIP 0.051 5% 1/8W* R1025 1-245-685-21 RES-CHIP 0.051 5% 1/8W* R1026 1-245-685-21 RES-CHIP 0.051 5% 1/8W

R1027 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR1028 1-208-911-11 METAL CHIP 10K 0.5% 1/16WR1029 1-208-884-81 METAL CHIP 750 0.5% 1/16WR1030 1-208-918-11 METAL CHIP 20K 0.5% 1/16WR1031 1-208-712-11 METAL CHIP 16K 0.5% 1/16W

R1032 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR1033 1-218-982-11 RES-CHIP 270K 5% 1/16WR1034 1-218-989-11 RES-CHIP 1M 5% 1/16WR1035 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR1036 1-208-923-11 METAL CHIP 33K 0.5% 1/16W

R1037 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR1038 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR1039 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR1040 1-216-789-11 METAL CHIP 2.2 5% 1/10WR1041 1-208-927-11 METAL CHIP 47K 0.5% 1/16W

R1042 1-216-864-11 SHORT CHIP 0R1043 1-218-977-11 RES-CHIP 100K 5% 1/16WR1044 1-218-977-11 RES-CHIP 100K 5% 1/16WR1045 1-218-953-11 RES-CHIP 1K 5% 1/16WR2001 1-208-923-11 METAL CHIP 33K 0.5% 1/16W

R2002 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR2003 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR2004 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR2005 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR2006 1-208-923-11 METAL CHIP 33K 0.5% 1/16W

R2007 1-208-943-11 METAL CHIP 220K 0.5% 1/16W

TK-071

Note: Two interchangeable kinds of IC are used forIC5002. It is included in TK-071 complete boardthough neither of these are supplied.

Note: IC5002には互換性のある2種類のICが使用されています。これらはいずれも供給されませんが，マウント済みTK-071基板に含まれます。


5-9


HVR-MRC1

R2008 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR2009 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR2010 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR2011 1-208-683-11 METAL CHIP 1K 0.5% 1/16W


R2017 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR2018 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR2019 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR2020 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR2021 1-208-695-11 METAL CHIP 3.3K 0.5% 1/16W

R2022 1-208-695-11 METAL CHIP 3.3K 0.5% 1/16WR2026 1-208-911-11 METAL CHIP 10K 0.5% 1/16WR2027 1-208-911-11 METAL CHIP 10K 0.5% 1/16WR2028 1-208-911-11 METAL CHIP 10K 0.5% 1/16WR2032 1-208-923-11 METAL CHIP 33K 0.5% 1/16W

R2033 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR2034 1-208-695-11 METAL CHIP 3.3K 0.5% 1/16WR2035 1-208-695-11 METAL CHIP 3.3K 0.5% 1/16WR2036 1-208-695-11 METAL CHIP 3.3K 0.5% 1/16WR2037 1-208-695-11 METAL CHIP 3.3K 0.5% 1/16W

R2038 1-208-695-11 METAL CHIP 3.3K 0.5% 1/16WR2040 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR2041 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR2042 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR2043 1-208-923-11 METAL CHIP 33K 0.5% 1/16W

R2044 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR2045 1-208-911-11 METAL CHIP 10K 0.5% 1/16WR2046 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR2048 1-218-990-81 SHORT CHIP 0R2049 1-208-923-11 METAL CHIP 33K 0.5% 1/16W

R2053 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR2055 1-208-911-11 METAL CHIP 10K 0.5% 1/16WR2064 1-218-990-81 SHORT CHIP 0R3001 1-208-647-11 METAL CHIP 33 0.5% 1/16WR3002 1-208-647-11 METAL CHIP 33 0.5% 1/16W

R4001 1-218-935-11 RES-CHIP 33 5% 1/16WR4002 1-218-935-11 RES-CHIP 33 5% 1/16WR4003 1-218-935-11 RES-CHIP 33 5% 1/16WR4004 1-218-935-11 RES-CHIP 33 5% 1/16WR4005 1-218-935-11 RES-CHIP 33 5% 1/16W



R4018 1-208-861-81 METAL CHIP 82 0.5% 1/16WR4019 1-208-861-81 METAL CHIP 82 0.5% 1/16WR4020 1-218-935-11 RES-CHIP 33 5% 1/16WR4021 1-208-861-81 METAL CHIP 82 0.5% 1/16W

R4022 1-218-935-11 RES-CHIP 33 5% 1/16W



R4034 1-208-911-11 METAL CHIP 10K 0.5% 1/16WR4035 1-208-911-11 METAL CHIP 10K 0.5% 1/16WR4036 1-218-962-11 RES-CHIP 5.6K 5% 1/16WR4037 1-208-911-11 METAL CHIP 10K 0.5% 1/16WR4038 1-218-961-11 RES-CHIP 4.7K 5% 1/16W

R4039 1-208-911-11 METAL CHIP 10K 0.5% 1/16WR4040 1-218-977-11 RES-CHIP 100K 5% 1/16WR4042 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR4043 1-208-911-11 METAL CHIP 10K 0.5% 1/16WR4047 1-208-911-11 METAL CHIP 10K 0.5% 1/16W

R4050 1-208-855-81 METAL CHIP 47 0.5% 1/16WR4051 1-218-953-11 RES-CHIP 1K 5% 1/16WR4055 1-208-911-11 METAL CHIP 10K 0.5% 1/16WR4056 1-218-990-81 SHORT CHIP 0R4057 1-218-990-81 SHORT CHIP 0

R4058 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR4059 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR4060 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR4061 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR4062 1-208-906-81 METAL CHIP 6.2K 0.5% 1/16W

R4063 1-208-663-11 METAL CHIP 150 0.5% 1/16WR4064 1-218-938-11 RES-CHIP 56 5% 1/16WR4065 1-218-938-11 RES-CHIP 56 5% 1/16WR4066 1-218-864-11 METAL CHIP 5.1K 0.5% 1/10WR4067 1-218-938-11 RES-CHIP 56 5% 1/16W

R4068 1-218-938-11 RES-CHIP 56 5% 1/16WR4069 1-216-864-11 SHORT CHIP 0R4070 1-216-864-11 SHORT CHIP 0R4071 1-216-864-11 SHORT CHIP 0R5018 1-218-961-11 RES-CHIP 4.7K 5% 1/16W

R5020 1-218-961-11 RES-CHIP 4.7K 5% 1/16WR5021 1-218-961-11 RES-CHIP 4.7K 5% 1/16WR5022 1-218-935-11 RES-CHIP 33 5% 1/16WR5023 1-218-961-11 RES-CHIP 4.7K 5% 1/16WR5024 1-218-938-11 RES-CHIP 56 5% 1/16W

R5027 1-218-961-11 RES-CHIP 4.7K 5% 1/16WR5028 1-218-990-81 SHORT CHIP 0R5034 1-208-923-11 METAL CHIP 33K 0.5% 1/16WR5035 1-218-953-11 RES-CHIP 1K 5% 1/16WR5036 1-208-911-11 METAL CHIP 10K 0.5% 1/16W


R5046 1-218-941-81 RES-CHIP 100 5% 1/16W

TK-071

5-10


HVR-MRC1

< VIBRATOR >

X4001 1-781-045-21 VIBRATOR, CRYSTAL (24.576MHz)* X5001 1-813-856-11 OSCILLATOR, CRYSTAL (27MHz)

TK-071

5-11EHVR-MRC1

• EXCEPT J MODELChecking supplied accessories.

CD-ROM (Note)“Manuals for Digital HD Video Camera Recorder”

Note:HVR-MRC1 is the accessory of HDR-Z7J/Z7U/Z7N/Z7E/Z7P/Z7C and HDR-S270J/S270U/S270N/S270E/S270P/S270C.Please refer to following CD-ROM that is those accessory for the Operating Instructions.・ 3-280-845-01 (for HDR-Z7J/Z7U/Z7N/Z7E/Z7P/Z7C)・ 3-280-849-01 (for HDR-S270J/S270U/S270N/S270E/

S270P/S270C)

* 3-290-149-01 (JAPANESE)* 3-290-149-11 (ENGLISH)* 3-290-149-21 (FRENCH)* 3-290-149-31 (SPANISH)* 3-290-149-41 (ITALIAN)* 3-290-149-51 (GERMAN)* 3-290-149-61 (SIMPLIFIED CHINESE)

Operating Instructions (PDF)

The CD-ROM supplied contains all of language version ofthe Operating Instructions (PDF) for printing.・ The printed matter is not supplied. If required, please

order it with the part number below.・ (Only for destination Japanese model) 日本国内については日本語のみが印刷での部品供給可能です。

• J MODEL付属品

CD-ROM (Note)「Manuals for Digital HD Video Camera Recorder」

Note:HVR-MRC1はHDR-Z7J/Z7U/Z7N/Z7E/Z7P/Z7C及びHDR-S270J/S270U/S270N/S270E/S270P/S270Cの付属品です。取扱説明書についてはそちらに付属の下記CD-ROMを参照

してください。・ 3-280-845-01 (HDR-Z7J/Z7U/Z7N/Z7E/Z7P/Z7C用)・ 3-280-849-01 (HDR-S270J/S270U/S270N/S270E/

S270P/S270C用)* 3-290-149-01 (日本語)

取扱説明書 (PDF)

印刷用の取扱説明書（PDF）は全ての言語が付属品の CD-ROMに含まれています。・印刷物は付属されておりません。必要な場合は下記部品番号にて注文となります。

6-1HVR-MRC1

6. ADJUSTMENTS

6-1. Reading/Clearing of History InformationThe history information recorded in this set can be read and cleared by connecting the set to the PC with the i.LINK cable and using batchfiles.

• Kind of history informationThis set records the following history information:1 Error codes (latest 10 codes)2 Accumulated POWER ON time (in minute)3 Accumulated recording time (in minute)4 Accumulated playback time (in minute)5 Accumulated files created6 Accumulated CF card detection count

1-1. Connection and Power ON Method

• Connection Diagram

Fig. 6-1-1

Procedures1) Attach the iLINK cradle (HVRA-CR1) to the set.2) Connect the set to the PC with the i.LINK cable.

Note: Remove the Compact Flash card if it has been inserted in the set.3) Slide the POWER switch of this set to ON.4) Check that the LCD screen of the set changes from “Welcome” to a blinking state of CF icon as shown below.

Fig. 6-1-2

Icon is blinking

AC Adapter/Charger

(Connecting cord)(DK-215)

HVR-MRC1

i.LINK cablePC withIEEE1394 terminal

6-2HVR-MRC1

1-2. List of Service Tools

• Files used

Folder Name File Name Remarks

Uploader 1394API.dll For installation of exclusive driver

1394DIAG.sys

1394vdev.inf

1394vdev.sys

port95nt.exe

CMD1394.exe

tnf.exe

batch_e HISTORY_E.bat Reading of history information

(English version) ERROR_E.bat Clearing of error code history

POWER_E.bat Clearing of accumulated POWER ON time

REC_E.bat Clearing of accumulated recording time

PB_E.bat Clearing of accumulated playback time

FILE_E.bat Clearing of accumulated files created

CFDET_E.bat Clearing of accumulated CF detection count

batch_j HISTORY.bat Reading of history information

(Japanese version) ERROR.bat Clearing of error code history

POWER.bat Clearing of accumulated POWER ON time

REC.bat Clearing of accumulated recording time

PB.bat Clearing of accumulated playback time

FILE.bat Clearing of accumulated files created

CFDET.bat Clearing of accumulated CF detection count

Note 1: OS: Windows XP HomeEdition (Service Pack2 or later)Windows XP Professional (Service Pack2 or later)Standard installation is required.Operation is not assured if rhe above OS has been upgraded.

CPU: MMX Pentium 200 MHz or fasterIEEE1394 terminal (DV connector)

Note 2: Retrieve the batch file etc. used from the item of “ESI Jig & Software” of “ESI homepage” by the following conditionsModel Name: HVR-MRC1Category: MPU/ROM/Software

Personal computer(Note 1)

J-1iLINK cable(Commercial item)

J-2 J-3

AC Adaptor/Charger(AC-VQ1050)1-479-580-11

Connecting cord(DK-215)1-783-710-24

J-4

6-3HVR-MRC1

1-3. Installation of Driver

Install the driver exclusive for confirmation of HVR-MRC1.Install the driver in the following procedures. Once this work isperformed, further installation is not required later on.Note: If the PC restarts after the driver installation completes,

starts from the procedure No. 15.

1. Double-click “Port95nt.exe” in the Uploader folder.2. According to the installation wizard, begin the installation.3. After the installation completes, restart the PC.4. After restarted, open “Control Panel” → “Add Hardware”, and

click “Next”.

Fig. 6-1-3

5. Select “Yes, I have already connected the hardware” and click“Next’.

Fig. 6-1-4

6. Select “Add a new hardware device” and click “Next”.

Fig. 6-1-5

7. Select “Install the hardware that I manually selected from alist” and click “Next”.

Fig. 6-1-6

8. Select “Show All Devices” and click “Next”.

Fig. 6-1-7

6-4HVR-MRC1

9. Click “Have Disk”.

Fig. 6-1-8

10. Click “Browse”.

Fig. 6-1-9

11. Select “1394vdev.inf” copied to the PC and click “Open”.

Fig. 6-1-10

12. Click “OK”.

Fig. 6-1-11

13. Select “1394 Virtual Device” and click “Next”.

Fig. 6-1-12

14. Click “Next”. Then, the installation starts.

Fig. 6-1-13

Note: When driver is installed, personaol computer might be re-set.In this case, please proceed work from procedure 15 afterstarting the personal computer.

6-5HVR-MRC1

15. Confirm the result of driver installation.Open “System Properties” → “Device Manager”.

Fig. 6-1-14

16. If “1394 Virtual device” is displayed below “1394 Test De-vices”, the installation is normally finished.

Fig. 6-1-15

17. If “Unknown device” is displayed below “1394 Test Devices”,update the driver in the procedures below.

Fig. 6-1-16

18. Right-click “Unknown devices” and select “Update Driver”.

Fig. 6-1-17

19. Select “Install from a list or specific location” and click “Next”.

Fig. 6-1-18

6-6HVR-MRC1

20. Click “Browse”.

Fig. 6-1-19

21. Specify the location (Uploader) where the driver is saved andclick “OK”.The installation starts.

Fig. 6-1-20

22. After the installation completes, click “Finish”.23. Open “Device Manager”. If “1384 Virtual Devices” is displayed

below “1394 Test Devices”, the installation is normally fin-ished.

Fig. 6-1-21

6-7HVR-MRC1

1-4. Reading of History InformationNote: The following shows a case that uses the batch file of En-

glish version.For Japanese version, use “HISTORY.bat”.

Procedures1. Double-click “HISTORY_E.bat” copied to the PC.2. The command prompt starts up. Following the message, press

the [ENTER] key of PC.

Fig. 6-1-22

3. The Notepad will open automatically and display the historyinformation.

Fig. 6-1-23

4. Close the Notepad. The command prompt window will closeautomatically.

5. The history information file “HISTORY.TXT” is created inthe same folder as HISTORY_E.bat, and accordingly you cansee the history information by opening the file with the texteditor, etc.If you execute HISTORY_E.bat with the HISTORY.TXT al-ready created, new history information will be added to theHISTORY.TXT with previously read history information re-mained unchanged.

1-5. Clearing of Error Code HistoryNote: The following shows a case that uses the batch file of En-

glish version.For Japanese version, use “ERROR.bat”.

Procedures1. Double-click “ERROR_E.bat” copied to the PC.2. The command prompt starts up.

Fig. 6-1-24

• To execute, press the [ENTER] key of PC. The clearing of errorcode history will be executed.

• To cancel, click “x” mark at the upper right of the commandprompt window to close the command prompt window.

3. When the clearing of error code history finished, the follow-ing message will be displayed in the command prompt win-dow.

Fig. 6-1-25

4. Press the [ENTER] key of PC to close the command promptwindow.

6-8HVR-MRC1

1-6. Clearing of Accumulated POWER ON TimeNote: The following shows a case that uses the batch file of En-

glish version.For Japanese version, use “POWER.bat”.

Procedures1. Double-click “POWER_E.bat” copied to the PC.2. The command prompt starts up.

Fig. 6-1-26

• To execute, press the [ENTER] key of PC. The clearing of accu-mulated POWER ON time will be executed.


3. When the clearing of accumulated POWER ON time finished,the following message will be displayed in the commandprompt window.

Fig. 6-1-27


1-7. Clearing of Accumulated Recording TimeNote: The following shows a case that uses the batch file of En-

glish version.For Japanese version, use “REC.bat”.

Procedures1. Double-click “REC_E.bat” copied to the PC.2. The command prompt starts up.

Fig. 6-1-28

• To execute, press the [ENTER] key of PC. The clearing of accu-mulated recording time will be executed.


3. When the clearing of accumulated recording time finished, thefollowing message will be displayed in the command promptwindow.

Fig. 6-1-29


6-9HVR-MRC1

1-8. Clearing of Accumulated Playback TimeNote: The following shows a case that uses the batch file of En-

glish version.For Japanese version, use “PB.bat”.

Procedures1. Double-click “PB_E.bat” copied to the PC.2. The command prompt starts up.

Fig. 6-1-30

• To execute, press the [ENTER] key of PC. The clearing of accu-mulated playback time will be executed.


3. When the clearing of accumulated playback time finished, thefollowing message will be displayed in the command promptwindow.

Fig. 6-1-31


1-9. Clearing of Accumulated Files CreatedNote: The following shows a case that uses the batch file of En-

glish version.For Japanese version, use “FILE.bat”.

Procedures1. Double-click “FILE_E.bat” copied to the PC.2. The command prompt starts up.

Fig. 6-1-32

• To execute, press the [ENTER] key of PC. The clearing of accu-mulated files created will be executed.


3. When the clearing of accumulated files created finished, thefollowing message will be displayed in the command promptwindow.

Fig. 6-1-33


6-10EHVR-MRC1

1-10. Clearing of Accumulated CF Detection CountNote: The following shows a case that uses the batch file of En-

glish version.For Japanese version, use “CFDET.bat”.

Procedures1. Double-click “CFDET_E.bat” copied to the PC.2. The command prompt starts up.

Fig. 6-1-34

• To execute, press the [ENTER] key of PC. The clearing of accu-mulated CF detection count will be executed.


3. When the clearing of accumulated CF detection count finished,the following message will be displayed in the commandprompt window.

Fig. 6-1-35


2008 Sony Corporation

3-290-149-11(1)

Memory RecordingUnit

HVR-MRC1

Owner’s record

The model number and the serial number are located at the name plate on the left of theunit. Record the serial number in the space provided below. Refer to these numberswhenever you call upon your Sony dealer regarding this product.

Model No. HVR- Serial No. ______________________

Operating Instructions

2

Table of contentsOn trademarks• “InfoLITHIUM” is a trademark of Sony Corporation.• i.LINK and are trademarks of Sony Corporation.• HDV and the HDV logo are trademarks of Sony

Corporation and Victor Company of Japan, Ltd.• Microsoft, Windows, Windows Vista and Windows Media

are either registered trademarks or trademarks of MicrosoftCorporation in the United States and/or other countries.

• Macintosh and Mac OS are registered trademarks of AppleInc. in the U.S. and other countries.

• CompactFlash is the registered trademark of SanDiskCorporation.

All other product names mentioned herein may be thetrademarks or registered trademarks of their respectivecompanies. Furthermore, ™ and “®” are not mentioned ineach case in this manual.

Notes on the LicenseANY USE OF THIS PRODUCT OTHER THAN CONSUMERPERSONAL USE IN ANY MANNER THAT COMPLIESWITH THE MPEG-2 STANDARD FOR ENCODING VIDEOINFORMATION FOR PACKAGED MEDIA IS EXPRESSLYPROHIBITED WITHOUT A LICENSE UNDER APPLICABLEPATENTS IN THE MPEG-2 PATENT PORTFOLIO, WHICHLICENSE IS AVAILABLE FROM MPEG LA, L.L.C., 250STEELE STREET, SUITE 300, DENVER, COLORADO 80206.

Overview ........................................................ 3

Names of parts ............................................... 4Memory Recording Unit / i.LINK Cradle ...................... 4LCD screen display ............................................................. 5

Using in VIDEO mode .................................... 6Connecting this unit to a camcorder ................................ 6Inserting/removing optional memory media ................ 6Menu settings ...................................................................... 6

Menu organization (VIDEO mode) ............... 7

Recording images from the camcorder to thisunit ................................................................. 9

Recording images(POWER switch at the ON side) ....................................... 9

Playback the image recorded on aCompactFlash in this unit ............................ 12

Playback (POWER switch to ON) .................................. 12Useful functions in combination with HVR-Z7/S270............................................................................................. 13

Using in COMPUTER mode.......................... 16Connecting to a computer ............................................... 16

Menu organization (COMPUTER mode)..... 17

Folder saving format ................................... 18Folder organization .......................................................... 18Notes regarding COMPUTER mode .............................. 19

Power supply ............................................... 20Preparing the power supply ........................................... 20

Trouble shooting.......................................... 22Power sources .................................................................... 22Recording ........................................................................... 22Connecting a computer .................................................... 23

Warning indicators ...................................... 24Self-diagnosis display ...................................................... 24Caution message ............................................................... 25

About i.LINK ................................................. 26

Optional CompactFlash ............................... 27CompactFlash .................................................................... 27

Specifications ............................................... 28

Precautions ................................................... 29

Getting the best performance from thebattery pack ................................................. 30

3

Integrated architecture to the camcorder• The body is small and light with a weight of about 130 g

and connects directly to a camcorder without a cable toprovide camcorder mobility. Power is supplied from thecamcorder so no additional battery is required; weight andsize have thus been minimized. The power-saving designalso enables longer recording time.

• The operational status such as operating mode, remainingCompactFlash capacity or recording format, etc. can bechecked on the LCD screen of the camcorder. Not having tocheck the unit itself means you can concentrate more onwhat you are shooting.

• The camcorder used with this unit can output a recordcommand without a tape inserted. This synchronizes theunit to the REC/STOP operation of the camcorder and soaudio and video can be recorded on the CompactFlash unitonly. A loop recording mode is also available whichenables you to record repeatedly.

Recording on small, light and highly versatileCompactFlash• CompactFlash used as recording media• CompactFlash is less subject to strong vibration or high

altitude and are highly resistant to impact such as beingdropped. This enables recording in a wide range ofenvironments.

• A highly versatile CompactFlash media (16GB) enablesabout 1 hour and 12 minutes of recording of an HDV/DVCAM/DV stream.

• Connecting the unit to a computer via a commercialCompactFlash reader allows faster data transfer to thecomputer than when using a tape. The data transfer timedepends on the specifications of the CompactFlash mediaand CompactFlash reader.

Can also connect to the HVRA-CR1 i.LINKcradle• The unit can be connected to a computer or camcorder via

the HVRA-CR1 i.LINK cradle.• The unit operates with a battery or AC adaptor via the

HVRA-CR1 i.LINK cradle, which enables you to record in awide range of environments.

• This unit has two operating modes, VIDEO mode andCOMPUTER mode. The mode is automatically selecteddepending on which device is connected. The unitindependently outputs playback video to the i.LINKinterface.

• VIDEO mode is for recording and playback an HDV/DVCAM/DV stream via the i.LINK terminal of thecamcorder.

• COMPUTER mode enables the unit to be recognized as anexternal drive when connected to a computer via an i.LINKterminal. This mode enables high-speed data transfer.

Overview

Supported models• This unit can be connected to a camcorder via a special

interface.• Refer to the supplied “Guide to supported models and

their functions” for details on supported models whenconnecting via an i.LINK terminal.

4

Names of parts

1 RELEASE buttonPress this button to remove this unit.

2 CAM LINK buttonPress this button to switch to CAM LINK [ON](FOLLOW/SYNCHRO) to record video in conjunctionwith the recording operation of the camcorder, or to CAMLINK [OFF] to record with this unit alone.* Default setting is CAM LINK [ON].

3 PREVIOUS/REW buttonPress this button during standby to go back to theprevious clip.Press this button during playback to stop playback andrestart playback from the beginning of the current clip.Keep this button pressed down during playback to playthe current clip backwards at triple the normal speed.When the menu screen is displayed on the LCD screen,press this button to move the cursor.

4 CompactFlash slot door OPEN latchSlide the button to open the CompactFlash slot door. Ifthe CompactFlash door is opened while the CompactFlashis being accessed, such as when recording or duringplayback, operations will stop.

5 LCD screen

6 MENU/LCD BACK LIGHT buttonPress this button to display the menu screen on the LCDscreen.Press the MENU/LCD BACK LIGHT button long enoughfor the backlight of the LCD screen to come on or off.

7 REPEAT buttonPress this button to change the auto repeat mode.Each time you press the button, the mode cycles througheach of the following changes.REPEAT1 (Repeatedly plays back the selected clip only)/ALL REPEAT (Repeatedly plays back all clips)/OFF

8 NEXT/FF buttonPress this button during standby to go to the next clip.Press this button during playback to stop playback andrestart playback from the beginning of the next clip.Keep this button pressed down during playback to playthe current clip forwards at triple the normal speed.When the menu screen is displayed on the LCD screen,press this button to move the cursor.

Memory Recording Unit / i.LINK Cradle

9 PLAY/EXEC buttonPress this button to play recorded files.Press this button during playback to pause playback.When the menu screen is displayed on the LCD screen,press this button to execute the selected menu item.

q; REC buttonPress two buttons together to start recording.

qa STOP buttonPress this button to return to the VIDEO mode screen.Press this button to stop recording or playback.When a menu is selected, press this button to cancel it.

qs POWER switchPress this button to turn the power of this unit on or off.The VIDEO mode and COMPUTER mode switchautomatically.

qd REC lamp/Access lampREC lamp/Access lamp comes on during recording inVIDEO mode.REC lamp/Access lamp blinks while accessing thecomputer in COMPUTER mode.

qf HDV/DV terminalConnect to a camcorder or computer with an i.LINKcable.

qg CompactFlash slot door

qh Eject leverPress this lever to eject the CompactFlash.

qj DC IN (DC power input) terminalConnect the AC adaptor etc. to supply power to this unit.

qk Attachment screw holeThis unit enables mounting to the camcorder equipped acold shoe or to directly mount to a tripod using theoptional shoe adaptor.Use a tripod with 5.5 mm or shorter screws.

67

5

89q;

qa

qs

qd

4

3

2

1

qfqh

qg

qj qk

Attaching to the i.LINK cradleAttach this unit to the i.LINK cradle by slidingthe unit in the direction of the arrow.

5

LCD screen display

1 Power supply displayThis icon is not displayed when this unit is connecteddirectly to the camcorder.Displays the power supply icons when connected to a PCor camcorder using the i.LINK cradle.

Battery pack in useDisplay the remaining battery capacity.

AC adapter connected

2 CAM LINK mode displayWhen the CAM LINK is set to ON, this icon is on.When the CAM LINK is set to OFF, this icon is off.

3 CompactFlash displayRemains on under normal conditions.Starts blinking in the following situations.• When the remaining recording time is less than 5

minutes• When the CompactFlash slot door is open• When the clip number is 9999

4 Clip number displayDisplays the selected clip number or recording/playbackclip number.

5 Remaining CompactFlash capacity displayDisplays the remaining recording time (in minutes).

6 Format type displayDisplays the recording/playback clip format.

7 TC (time code) displayDisplays the time code.

VIDEO mode

During recording During playback

8 Status displayDisplays the status with an icon.x Power is on and playback/recording is stoppedz RecordingN Playbacku Pausing playbackM Fast-forwardm Rewind

9 REC mode displayDisplays REC mode setting in the menu.NORMAL Not displayed.

Cache recording mode

Interval recording mode

Loop recording mode

q; Repeat mode displayDisplays the repeat status during playback.

REPEAT 1

REPEAT ALL

qa Loop recording displayTime display of 5 is the total time recorded by looprecording.Displays [L] to the left of the time display.

1

9 6

8 7

2 3 4 qa5

q;

6

Connecting this unit to a camcorder

Refer to the operating instructions of the camcorder.Connecting the shoe connector of the unit enables thecamcorder to supply power and a stream signal.

Inserting/removing optionalmemory media

• Although this unit has been tested with CompactFlash,Sony does not guarantee its operation with allCompactFlash.The operation of this unit with Sony CompactFlash hasbeen checked.

• CompactFlash with 133x 2GB or more specifications arerecommended for this unit. (A speed of less than 133x isnot guaranteed; space less than 2GB is not guaranteed.)

• Always format a new CompactFlash with this unitbefore use.

• Do not remove the CompactFlash while the access lampis blinking.

Inserting the CompactFlash

1 Open the CompactFlash slot door while sliding theOPEN latch.

2 Push the CompactFlash in the correct direction until itclicks into place.

3 Close the CompactFlash slot door.

Using in VIDEO mode

1

3

2

1 1

Removing the CompactFlash

1 Open the CompactFlash slot door and push the ejectlever 1 to remove the CompactFlash.

2 Close the CompactFlash slot door.

CompactFlash capacity and availablerecording time

CompactFlash available recording time

2GB Approx. 9 min.

4GB Approx. 18 min.

8GB Approx. 36 min.

16GB Approx. 72 min.

Notes

Do not repeatedly insert or remove the CompactFlash over ashort amount of time. Doing so may cause mis-recognition ofthe CompactFlash and memory malfunction. If you open theCompactFlash slot door while the unit is recording or inplayback, operations will stop. If that occurs, be sure that thestatus on the LCD screen changes to x (playback/recordingis stopped) before removing the CompactFlash.When ejecting the CompactFlash, forcefully pressing the ejectlever and allowing the CompactFlash to be pointeddownward when ejected will cause the CompactFlash to fall.

Menu settings

Check the individual settings and change them if necessary.For details, see page 7.

1 Display the menu screen on the LCD screen bypressing the MENU button.

2 Select the desired setting by pressing the PREVIOUS/REW button or the NEXT/FF button and press thePLAY/EXEC button.

3 Select the desired item by pressing the PREVIOUS/REWbutton or the NEXT/FF button and press the PLAY/EXEC button.

4 Return to the VIDEO mode screen by pressing theSTOP button. Press the MENU button to close themenu screen.

Notes

You cannot record or play back movies while the menuscreen is displayed on the LCD screen. Also, you cannotchange to the menu screen on the LCD screen duringrecording or playback.

7

CLIP SELECTYou can select the clip number directly.Press the PREVIOUS/REW (previous clip/rewind) or NEXT/FF (next clip/fast-forward) button to select the number andpress the PLAY/EXEC (playback/execute) button.Select the digits one by one. The display returns to the menuafter four digits are selected.If there is no clip number, the previous clip number isselected.

DELETEDeletes the recorded data or formats the CompactFlash.• CLIPDisplays the three clip numbers from those displayed on thenormal screen.Selects and deletes clips.• ALLDeletes all the recorded clips.• FORMATFormats the CompactFlash.

Menu organization (VIDEO mode)

REC MODE• NORMALSets the normal recording mode.• CACHESets the cache recording mode.• INTERVALSets the interval recording mode. Only DVCAM/DV formatis valid.• LOOPSets the loop recording mode.

Notes

When inputting the stream signal from the i.LINK,INTERVAL and LOOP is valid.

i.LINK MODE• AUTO ....... Automatically switches to the camcorder

recording/playback format.• HDV .......... Plays back HDV format only.• DV ............. Plays back DVCAM (DV) format only.

If there is no clip, you cannot make a selection.

root CLIP SELECT

DELETE

REC MODE

i.LINK MODE

SETTING

ALL RESET

CLIP

ALL

FORMAT

NORMAL

CACHE

INTERVAL

LOOP

AUTO

HDV

DV

TC FORMAT

DV FILETYPE

INTERVAL

CAMLINK SEL

SLEEP MODE

CAMERA NO

AUTO

NDF

DF

AVI

RAW DV

REC TIME

INT.TIME

FOLLOW

SYNCHRO

OFF

1min

5min

0.5sec

1sec

1.5sec

2sec

30sec

1min

5min

10min

* Boldface settings are default settings.

8

SETTING

TC FORMATFollows the DF/NDF of the time code from the camcorderconnected to this unit.• AUTO ....... Follows the time code format of the camcorder.• NDF ........... Records the time code in NDF format.• DF .............. Records the time code in DF format.

Notes

The default [AUTO] setting is NDF. If time code informationfrom the camcorder is not obtained, this unit is set to the mostrecent recording setting.

DV FILE TYPEChanges the DV recording format.• AVI ............ Records video in AVI format.• RAW DV... Records video in DV format.

INTERVAL• REC TIMESelects the interval recording time.You can select [0.5sec], [1sec], [1.5sec] or [2sec].• INT.TIMESelects the interval time between recordings.You can select [30 sec], [1 min], [5 min], or [10 min].

CAM LINK SELWhen CAM LINK is set to [ON], select the type of camcorder-linked operation.• FOLLOW ...... Uses this setting when connecting to a

camcorder that has no “external RECcontrol” function. The unit follows thecamcorder operation.

• SYNCHRO ... Uses this setting when connecting to acamcorder that has an “external RECcontrol” function. The unit operatessimultaneously with the camcorder.

SLEEP MODESwitches the sleep mode ON/OFF.• OFFSleep mode is set to OFF.• 1minIf the i.LINK cable is disconnected and no operation is donefor more than one minute, this unit automatically switches toSLEEP status.• 5minIf the i.LINK cable is disconnected and no operation is donefor more than five minutes, this unit automatically switchesto SLEEP status.To return to normal status, reconnect the i.LINK cable to thisunit or turn the POWER switch off and back on.

Notes

In SLEEP MODE, this unit is not completely switched off butcontinues to run using low power consumption.

CAMERA NOYou can assign a number to the data clip name whenrecording.Use this mode to assign non-overlapping numbers to clipnames recorded simultaneously on more than one camcorder,or to manage clip data by assigning numbers.Press the PREVIOUS/REW (previous clip/rewind) or NEXT/FF (next clip/fast-forward) button to select the number andpress the PLAY/EXEC (playback/execute) button.Select the digits one by one. The display returns to the menuafter two digits are selected.The factory default setting is [00].

ALL RESETRestores all default settings.

9

Recording images from the camcorder to this unit

x Recording video simultaneously on this unit anda camcorder

– Connecting to a camcorder with an “external RECcontrol” function (SYNCHRO mode)When connected to a camcorder that has an external RECcontrol function, this unit can be controlled by thecamcorder to record video data simultaneously to thecamcorder recording on tape.• Clips recorded by this unit include several frames after

the recording stopping point on the tape.

1 Press the CAM LINK button of this unit and set it toON.

2 Set the [CAM LINK SEL] setting of this unit to[SYNCHRO].

3 Set the [EXT REC CTRL] setting of the camcorder to[SYNCHRONOUS].

4 Connect the camcorder to this unit via an i.LINK cable.

5 Press the REC START/STOP button of the camcorder tostart recording.

• The above Step 3 is for the HVR-Z7/S270 series. For detailson another camcorder you want to connect to this unit,refer to the operating instructions supplied with thatcamcorder.

• For details on the types of camcorder that have an “externalREC control” function and on motion detection, refer to the“Guide to supported models and their functions” suppliedwith this unit.

– Connecting to a camcorder without an “externalREC control” function (FOLLOW mode)When connected to a camcorder that has no external RECcontrol function, this unit regularly checks the status ofthe camcorder and follows its recording operation.


2 Set the [CAM LINK SEL] setting of this unit to[FOLLOW].



Notes

• This unit may lag up to two seconds behind the taperecording/stopping point of the camcorder.

• For details on camcorders that have been tested inFOLLOW mode, refer to “Guide to supported modelsand their functions” supplied with this unit.

Camcorder STANDBY R E C STANDBY

This unit STANDBY R E C STANDBY

REC

Camcorder

STOP

STANDBY REC STANDBY

This unit STANDBY REC STANDBY

Images recorded by the camcorder can be recorded onto thisunit.

Recording images(POWER switch at the ON side)

The different methods of recording are as follows:

x Recording video simultaneously on this unit anda camcorder

x Recording on this unit during camcorder tapereplacement

x Recording video from this unitx Operating cache recordingx Operating interval recordingx Operating loop recording

Notes

• A 0 KB file may be created, but the file cannot be openedbecause it does not have video data. Do not delete the 0 KBfile on your computer. If you do, this clip cannot be playedback.

• When changing the tape, the audio may mute on somecamcorder models. At the recorded part, only video isrecorded.

• When HDV recording with this unit, if you start the taperecording with the camcorder, the i.LINK output stream iscut for about 0.5 seconds, so when that video is recordedonto this unit, it is the cut form. In this case, the file will beseparated before and after changing the tape recordingstarted.

• The file will be separated automatically every time therecording time of one clip over about 20 minutes but thisclip is operated as a same clip.

• If the i.LINK cable is disconnected or the power of theconnecting device turned off during recording, recordingstops but the data recorded until that point is recorded.

• If the power of this unit is turned off by battery exhaustionor mistakenly sliding the POWER switch, the data recordeduntil the power off is detected is recorded on aCompactFlash in this unit.

• If the battery pack is removed or the jack of the AC adaptordisconnected during recording, the folder information atthe moment the power goes off may not be writtencorrectly.

• The interval recording operation of the camcorder is nottimed, so operations are not guaranteed.

• Do not switch the audio mode of the camcorder whilerecording. Depending on the PC application, there may notbe any audio.

10

x Recording on this unit during camcorder tapereplacementWhen connected to a camcorder that has an external RECcontrol function, you can record video on this unit onlywhile changing the tape of the camcorder.


2 Set the [CAM LINK SEL] setting of this unit to[SYNCHRO].

3 Set the [EXT REC CTRL] setting of the camcorder to[RELAY].



• When the remaining time of the tape is less than 5 minutes,the camcorder sends a command to this unit to startrecording.

• The recording by this unit can be stopped from thecamcorder after changing the tape or by pressing the STOPbutton of this unit.

• The noise of the tape change is recorded.• The above Step 3 is for the HVR-Z7/S270 series. For details

on another camcorder you want to connect to this unit,refer to the operating instructions supplied with thatcamcorder.

• For details on camcorders that have an “external RECcontrol” function and on motion detection, refer to the“Guide to supported models and their functions” suppliedwith this unit.

Notes

• During RELAY recording, the cache recording cannot beoperated.

x Recording video from this unitYou can use this unit to start or stop recording a videoinput signal from an i.LINK without linked operation to adevice connected via i.LINK.

1 Press the CAM LINK button of this unit and set it toOFF.

2 Slide the REC button to start recording.

REC

Camcorder

STOP

REC Changing the tape

5 minutes before end of tape

STANDBY

This unit STANDBY REC STANDBY

REC

Camcorder STANDBY REC STANDBY

This unit STANDBYREC REC REC STANDBYSTANDBY

Cache recording modeThe most recent approximately maximum 14 seconds ofvideo and audio captured by the camcorder are held in abuffer memory and automatically recorded when therecording button is pressed.

To set cache recordingSelect [CACHE] from [REC MODE] on the menu screen.

Notes

• After cache recording, it may take about 30 seconds to writedata of the cache part.

Interval recording modeRecords a series of videos at regular intervals.This function is useful to observe things like cloudmovements or daylight changes. Only DVCAM/DV format isvalid.

Selecting an interval recording timeSelect [SETTING] t [INTERVAL] t [REC TIME] on themenu screen to set the time.You can select [0.5sec], [1sec], [1.5sec] or [2sec].

Setting the interval timeSelect [SETTING] t [INTERVAL] t [INT TIME] on themenu screen to set the time.You can select [30sec], [1min], [5min] or [10min].

Setting interval recordingSelect [INTERVAL] from [REC MODE] on the menu screen.

LCD screen display in interval recording mode

Remains on duringrecording and blinksduring standby

11

Remains on during recording

Notes

• The speed will slow according to the volume of data beingwritten because of limitations of the CompactFlashcapacity. For that reason, the following usages arerecommended when operating loop recording;– Use a new CompactFlash (more than 300x).– Format a CompactFlash before starting loop recording.

• CAM LINK is turned OFF automatically while in theinterval and loop recording modes. Press the REC button tostarting recording.

• The data recorded by loop recording mode is updated atregular intervals. When updating the data, the wholerecording time may be shortened.

• Updates the data regardless of update intervals whenstarting recording by a camcorder during loop recordingmode in HDV.

Loop recording modeRepeats overwrite-recording using the available space on theCompactFlash.You cannot select this mode if the remaining recording timeis less than 5 minutes (CompactFlash icon is flashing).

Setting loop recording modeSelect [LOOP] from [REC MODE] on the menu screen.

LCD screen display in loop recording mode

12

Playback the image recorded on aCompactFlash in this unit

To play back video clip recorded on a CompactFlash in thisunit, you need to connect this unit to a playback device via ani.LINK cable.

Playback (POWER switch to ON)

The playback method is as follows.• Standard playback• Trick playback• Repeat playback

To select the playback formatSelect i.LINK MODE on the menu screen and select thedesired setting, AUTO, HDV or DV.For details on selecting the menu, see page 6.

– AUTOAutomatically switch the HDV/DV format signal duringplayback.

– HDVOnly play back the part recorded in HDV format.

– DVOnly play back the part recorded in DVCAM (DV) format.

Standard playbackIn this mode, the recorded clip in this unit is output to thei.LINK depending on the type of format.

To play back normally

Select the clip number in CLIP SELECT of the menu, ordisplay the desired clip number on the LCD screen bypressing . or >.

Play back the image by pressing the H button on thisunit.• When you pause during playback with this unit, no stream

is output.• During playback, the screen may become momentarily blue

or frozen for about 0.5 second at the transition betweenscenes (when switching clips).

Trick playbackWhen the playback image is output to i.LINK, the clip isplayed at 3x, 6x, and 9x the normal speed.

To play back at the changed speedKeep pressing . or > button during playback to startplayback at the changed speed.• The sequence of change is 3x, 6x, 9x and then back to 3x.• It takes a few seconds for playback to start at the changed

speed.• The screen may not be displayed correctly during trick

playback or playback. If that situation occurs, stop theplayback once and try to replay.

Repeat playbackThis unit can automatically repeat playback of all or one clipin this unit.

To set repeat modeDisplay or on the LCD screen by pressing theREPEAT button on this unit.

– REPEAT 1The recorded image in the desired clip is repeatedlyplayback.

– ALL REPEATALL REPEAT plays back all recorded images in this unitto the last clip then goes back to the first clip and repeatsplayback.

– OFFStart playback from the desired clip and stop it afterplayback of the last clip.

Clip Clip number OFF REPEAT 1

REPEAT mode

REPEAT ALL

Clip A File A-1

File A-2

File A-3

Clip B File B-1

File B-2

File B-3

Clip C File C-1

File C-2

File C-3

13

You can record the time code of the HVR-Z7/S270 without atape in the HVR-Z7/S270.

If you want to record video using the time code ofthe HVR-Z7/S270, set the time code setting of theHVR-Z7/S270 as follows.

Time code value always advances.• TC MAKE ........ PRESET• TC RUN ........... FREE RUN

Time code value only advances during recording.• TC MAKE ........ PRESET• TC RUN ........... REC RUN

In combination with the time code settings of the HVR-Z7/S270, this unit operates as follows.

Useful functions in combinationwith HVR-Z7/S270

Tapeless external REC controlEven if there is no tape in the HVR-Z7/S270, you can start orstop recording the image on this unit.

Set the EXT REC CTRL setting of the HVR-Z7/S270 asfollows.• REC CTRL MODE ..... EXT ONLY

You can start or stop recording the image on aCompactFlash in this unit with START/STOP button only.(If there is a tape in the HVR-Z7/S270, you can startrecording video data with REC button of the video cameraoperation part, stop recording video data with STOP buttonof the video camera operation part on the tape.)

TipsIf there is no tape in the SYNCHRONUS or RELAY settings,you can start or stop recording the image on a CompactFlashin this unit.

• STBY COMMAND..... Desired setting* For details, refer to the operating instructions for the

external REC control of the HVR-Z7/S270.

Set this unit as follows.• CAM LINK SEL.......... SYNCHRO• Press the CAM LINK button to set to CAM LINK [ON].

TC MAKE

REGENERATE

PRESET

TC RUN

–

REC RUN

FREE RUN

Time code of thisunit with a tape inthe HVR-Z7/S270

When startingrecording on a tape,video is recordedusing the time codeof the tape base.If the time code ofthe tape base cannotbe read, the timecode starts from00:00:00:01.

When startingrecording on a tapeor CompactFlash inthis unit, the timecode value advancesfrom the preset timecode of the HVR-Z7/S270.

The preset time codevalue advancesconstantly and datais recorded using thedata code.

Time code of thisunit without a tapein the HVR-Z7/S270

The internal timecode of this unitruns automatically.

When startingrecording onCompactFlash inthis unit, the timecode valueadvances from thepreset time code ofthe HVR-Z7/S270.

The preset timecode valueadvances constantlyand data is recordedusing the data code.

• If you want to use REC RUN with a tape in the HVR-Z7/S270, set REC CTL MODE of the HVR-Z7/S270 to[SYNCHRONOUS] and set CAM LINK SEL of this unit to[SYNCHRO].

14

– Indicators• The following information can be displayed on the LCD

screen of the HVR-Z7/S270.

1 CompactFlash connecting statusThis icon blinks when the remaining recording time of theCompactFlash is low or an error has occurred in this unit.

2 CompactFlash modeThe same icon as the mode icon of this unit is displayed.

Display the operational status of this unit on the HVR-Z7/S270 LCD screen

CAMERA mode

CompactFlash mode Mode icon

STANDBY x

REC z

12

– Status check indicator• The following information can be displayed on the status

check indicator (CAMERA mode) of the HVR-Z7/S270.

REC FORMATDisplays the recording format of this unit.

STATUSDisplays the status (recording, playback etc.)

TIME CODEDisplays the time code during recording.

CLIPDisplays the clip number during recording.

CAM LINKDisplays the CAM LINK status of this unit.(When CAM LINK [OFF] is set, you cannot record from theHVR-Z7/S270.)

REMAINDisplays the CompactFlash remaining recording time.

REMAINDisplays the battery level.(When connected to an AC adaptor/charger, “AC” isdisplayed.)Not displayed when this unit is connected to the camcorder.It is displayed when the unit is connected to the i.LINKcradle.

15

– Indicators• The following information can be displayed on the LCD

screen of the HVR-Z7/S270.

1 CompactFlash connecting statusThis icon blinks when the remaining recording time of theCompactFlash is low or an error has occurred in this unit.

2 CompactFlash modeThe same icon as the mode icon of this unit is displayed.

3 Time code of the playback signal of this unitThis time code is displayed during playback of a videorecorded by this unit.

4 Data codeThis data code is displayed during playback of a videorecorded by this unit.

VCR mode

2

1

4

CompactFlash mode Mode icon

STANDBY x

PLAY N

FF M

REW m

PLAY PAUSE u

REC z

– Status check indicator• The following information can be displayed on the status

check indicator (VCR mode) of the HVR-Z7/S270.

PB FORMATDisplays the playback format of this unit.

STATUSDisplays the status (recording, playback etc.)

CLIPDisplays the clip number during playback.

REPEAT MODEDisplays the playback mode. (“1” means “repeat 1 clip,”“ALL” means “repeat all clips.”)

REMAINDisplays the CompactFlash remaining recording time.

REMAINDisplays the battery level.(When this unit is connected to an AC adaptor/charger,“AC” is displayed.)Not displayed when this unit is connected to the camcorder.It is displayed when the unit is connected to the i.LINKcradle.

3

16

Using in COMPUTER mode

Connecting to a computer

You can transfer recorded images on this unit as a file inHDV or DV format to a nonlinear editing system orcomputer.

1 Attach the HVRA-CR1 i.LINK cradle and optional ACadaptor to this unit.For extended use, the AC adaptor is recommended.This unit can still be operated with the battery packattached.

2 Connect this unit to the computer via the optionali.LINK cable.

3 Slide the POWER switch of this unit to ON.

Note

This unit cannot receive power from the computer.

Computer requirements

For Windows users• OS: Windows 2000 Professional (Service Pack 4 or later)/

Windows XP Home Edition (Service Pack 2 or later)/Windows XP Professional (Service Pack 2 or later) /Windows VistaStandard installation is required.Operation is not assured if the above OS has beenupgraded.

For Macintosh users• OS: Mac OS X (v10.3 or later)

When this unit is set to COMPUTER mode, the followingscreen is displayed on the LCD screen.

1

3

2

17

HDVOperate in the VIDEO mode. Set this mode when reading orwriting HDV stream data on a CompactFlash in this unitusing editing software.

DV-NTSCOperate in the VIDEO mode. Set this mode when reading orwriting DV (NTSC format) stream data on a CompactFlash inthis unit using the editing software.

DV-PALOperate in the VIDEO mode. Set this mode when reading orwriting DV (PAL format) stream data on a CompactFlash inthis unit using the editing software.

DRIVEOperate as an external removable media of the computer.(Default setting)

SETTINGYou can set this when in VIDEO mode.Settings are reflected in setting in the VIDEO mode operationwhen connecting to a camcorder.For details about setting, refer to “Menu organization(VIDEO mode).”

Menu organization (COMPUTER mode)

root HDV

DV-NTSC

DV-PAL

DRIVE

SETTING TC FORMAT

DV FILETYPE

CAMERA NO

AUTO

NDF

DF

AVI

RAW DV

*Boldface settings are default settings.

Notes

• For the following cases, operate “Safety remove Device (forWindows)” or “Remove by putting the media icon into thetrash (for Mac OS)” etc., and check that the access lampturns off.– When switching the each modes DRIVE, HDV or DV-

NTSC, DV-PAL– When disconnecting the i.LINK cable from the computer– When turning off the power of this unitTo recognize this unit again after these operations,disconnect i.LINK cable from the computer once, thenreconnect it.

• Depending on the video editing software, this unit may notbe recognized without switching the mode before startingthe software.

• If you change the operation mode frequently, the computerand this unit may not communicate correctly. Switch themode of this unit at intervals about 5 seconds or more.

• HDV, DV-NTSC, and DV-PAL mode may not berecognized because of a limitation of the computer whenswitching them directly.If that situation occurs, disconnect this unit from thecomputer, then select the mode.

• If the combination of the settings of the editing software(HDV/DV-NTSC, DV-PAL) and this unit are incorrect,images may be distorted or recognized incorrectly.

18

Folder saving format

XX_CCCC_YYYY-MM-DD_hhmmss.M2TData recorded in HDV formatWhen playback, HDV compatible playback software isneeded.

XX_CCCC_YYYY-MM-DD_hhmmss.AVIDV format data recorded when DV FILE TYPE is set toAVI

When not setting the clock set, file name will be “xx_cccc_0000-00-00_000000.extension.”When the file is separated, the bottom number of the file name will be counted up.When cache recording in HDV format, the cache part may be separated as a 14-second file (maximum).

FilesThe maximum file size is 4 GB. If a file size exceeds 4 GB, that file is automatically divided.

Folder organization

The file/folder organization of this unit is as follows.

XX_CCCC_YYYY-MM-DD_hhmmss.DVDV format data recorded when DV FILE TYPE is set toRAW DVFor playback on Windows, Raw DV compatible playbacksoftware is needed.

XX_CCCC_YYYY-MM-DD_hhmmss.IDX and Tracks.dat

Information files of recording data in folders(number of files, number of frames, starting time code,etc.)Used with a connection tool. Do not delete this file.

Notes

• During HDV recording, a new file will be created at the recording starting point of the tape.• Segmented files recorded from HDV stream

Some computer applications cannot play back the transitions between segmented files properly. If this happens, join the filesusing the “Sony Recording Unit Utility” or “M2T File Connection Tool” (*).* Available from the Sony support page

Media ROOT VIDEO HVR XX_CCCC_YYYY-MM-DD_hhmmss.M2TXX_CCCC_YYYY-MM-DD_hhmmss.IDX

XX_CCCC_YYYY-MM-DD_hhmmss.M2TXX_CCCC_YYYY-MM-DD_hhmmss.IDX

XX_CCCC_YYYY-MM-DD_hhmmss.AVIXX_CCCC_YYYY-MM-DD_hhmmss.IDX

XX_CCCC_YYYY-MM-DD_hhmmss.AVIXX_CCCC_YYYY-MM-DD_hhmmss.IDX

XX_CCCC_YYYY-MM-DD_hhmmss.DVXX_CCCC_YYYY-MM-DD_hhmmss.IDX

XX_CCCC_YYYY-MM-DD_hhmmss.DVXX_CCCC_YYYY-MM-DD_hhmmss.IDX

Tracks.dat

• XX : Camera No. (00 to 99)

• CCCC : Clip No. (0001 to 9999)

• YYYY : Year (1995 to 2094)

• MM : Month (01 to 12)

• DD : Day (01 to 31)

• hh : Hour (00 to 23)

• mm : Minute (00 to 59)

• ss : Second (00 to 59)

• M2T/AVI/DV : Extension

An actual file name has numbers as thefollowing information.

19

Notes regarding COMPUTER mode

• Do not save other data files in the HVR folder.• Do not transfer data from a computer to this unit in COMPUTER mode.

Write back data from a computer to this unit by streaming.Write back data after selecting HDV or DV-NTSC, DV-PAL format in PC MODE in the menu.

• Do not change folder or file names on your computer.Delete data or format a CompactFlash on this unit to increase the capacity of the CompactFlash.

• When removing the CompactFlash media by OS operation from a computer, do not disconnect i.LINK cable or switch themode of this unit.

• Do not use defragmentation on your computer.• Due to the limitations of Windows, this unit may not be detected when normal computer operation is restored after standby

or hibernation. For this reason, hibernation is not supported by this unit.• Due to the specifications of Mac OS X, to disconnect this unit from a Mac with Mac OS X and connect it again, perform the

following steps.

To reuse this unit

1 To use this unit, restart the computer or use Disk Utility. To use Disk Utility, follow the steps.

2 Start Disk Utility (/Applications/Utilities/).

3 Click the triangle mark on the left of the CompactFlash icon to display the CompactFlash volume and partitionname.

4 Select grayed out partition name (“VIDEO”) from Disk Utility window.

5 Select [Mount] from the [Option] menu. The selected name “VIDEO” is displayed on the desktop again.(If it is still unmounted, select [Unmount] and then select [Mount] again.)

6 Exit Disk Utility.

20

Preparing the power supply

The following will explain the optional AC-VQ1050 ACadaptor/charger.

To charge the battery packWhen using an “InfoLITHIUM” battery pack (L-series,optional) as the power supply for this unit, charge the batteryback as follows before use.

When charging the battery pack, refer to the operatinginstructions supplied with the AC adaptor/charger(optional).

1 Set the mode change switch of the AC adaptor/charger to CHARGE.

Notes

You cannot charge when the mode change switch is set toVCR/CAMERA.

2 Connect the AC power cord to the AC adaptor/charger.

3 Connect the AC power cord to a wall outlet.

4 When installing the battery pack, press it down whilesliding it in the direction of the arrow.Charging begins and the CHARGE lamp on the ACadaptor/charger comes on.When charging is completed, all of the segments of thebattery life indicator appear in the display window(normal charge).The CHARGE lamp goes off, but if you continue charginguntil the “FULL” battery life indicator appears, the batterycapacity will be slightly longer (full charge).

5 When charging is completed, remove the battery packfrom the AC adaptor/charger.

Notes

• This unit can be used with an “InfoLITHIUM” battery pack(L-series), but does not support the battery info function.

• This unit cannot be used to charge the battery packinstalled.

Power supply

Remaining battery time indication in the ACadaptor/charger display windowThis indication is provided by data communications betweenthe AC adaptor/charger and the “InfoLITHIUM” batterypack.This unit does not have a data communications function, sothe displayed time may differ from the actual remaining time.This is not a malfunction.

Charging timeCharging times for a completely exhausted “InfoLITHIUM”battery pack (NP-F570, NP-F770, NP-F970) are as follows.

Battery pack Time for full (Time for normalcharge charge)

NP-F570 Approx. 145 minutes (Approx. 85 minutes)



Operating times for continuous recordingOperating times for continuous recording using an“InfoLITHIUM” battery pack (NP-F570, NP-F770, NP-F970)are as follows.

Battery pack Operating time (Operating timefrom full charge from normal charge)



NP-F970 Approx. 1,320 minutes (Approx. 1,180 minutes)

Battery packBefore changing the battery pack, slide the POWER switch toOFF (CHG).

Charging/recording/playback time• Times measured with the camcorder at 25°C (77°F)

(Recommended range is 10°C to 30°C (50°F to 86°F)).• Recording and playback times are shorter at lower

temperatures.• Recording and playback times are shorter depending on

the conditions of use of this unit.• Except for the NP-F570/F770/F970, operating time is not

ensured.

2

344

1AC adaptor/charger AC-VQ1050B(optional)

Mode changeswitch

Battery pack

CHARGE lamp

21

AC adaptor/chargerDo not short-circuit the DC plug of the AC adaptor/chargeror battery terminal with any metallic objects. This may causea malfunction.

To install the battery pack to this unitSlide the battery pack in the direction of the b mark onthe battery pack.

To remove the battery pack from this unitPress the BATT RELEASE button of this unit and slide thebattery pack in the direction of the arrow.

To connect this unit to a wall outletFor prolonged operation, such as playing the recordedimages, you can operate this unit from a domestic wall outletwithout worrying about battery life.

1 Set the mode change switch of the AC adaptor/charger to VCR/CAMERA.

Notes

When the mode change switch is set to CHARGE, there isno power supply.

2 Connect the DK cable to the DC IN jack on this unit.

3 Connect the DK cable to the AC adaptor/charger.

4 With the power cord, connect the AC adaptor/chargerto a wall outlet.

Notes

You can leave the battery pack installed while operating fromAC power. The power supply to the DC IN jack has priority.

To use the AC adaptor/charger from a vehiclepower supplyFor details, refer to the operating instructions supplied withthe AC adaptor/charger.

Notes on battery pack/AC adaptor• Avoid the following while the ACCESS lamp is lit. Failure

to do so may cause malfunction.– Removing the battery pack– Removing the AC adaptor (while charging with the AC

adaptor)• Always turn off the POWER switch before removing the

battery pack or the AC adaptor.

22

Symptom Cause/Remedy

Pressing the REC switch does notstart recording.

The ACCESS lamp remains on evenwhen you stop recording.

Recording stops.

Trouble shooting

Please check the following before contacting your Sony dealer.

Note in case of repairs• Some kinds of repair work may require that the CompactFlash be formatted or replaced. In either case, all data on the

CompactFlash will be deleted. Back-up your data from the CompactFlash before sending it for repairs. Sony does notguarantee against data being deleted during repair work.

• During repair work, Sony may perform a minimal check of the data on a CompactFlash in order to verify improvements orthe occurrence of defective symptoms. However, Sony never copies or saves the data.

Power sources


This unit gets warm.

The remaining battery time indicatordoes not indicate the correct time.

The battery pack discharges tooquickly.

Recording

• This unit is writing the video you just shot to the CompactFlash.t Wait for a while and then slide the REC switch.

• The CompactFlash of the unit is full.t Delete unnecessary images.t Format this unit by selecting DELETE and then FORMAT.

• This unit is recording the image you just shot.t Do not remove the AC adaptor or the battery pack while the lamp is turned on.

• Fragmentation has occurred.t Format this unit by selecting DELETE and then FORMAT.

• This unit may get warmer while you use it. This is not a malfunction.

• The ambient temperature is too high or too low, or the battery pack has not beencharged enough. This is not a malfunction.t Fully charge the battery pack again. If the problem persists, the battery pack

may be worn out. Replace it with a new one (p. 20).• The indicated time may not be correct in certain circumstances.

• The ambient temperature is too high or too low, or the battery pack has not beencharged enough. This is not a malfunction.t Fully charge the battery pack again. If the problem persists, the battery pack

may be worn out. Replace it with a new one (p. 20).

23


An error message appears when youplace the supplied CD-ROM in yourcomputer.

The image or sound on this unitcannot be played back correctly.

The extension of a file is notdisplayed on your computer.

Connecting a computer

t Set the computer display as follows:– 1024 × 768 dots or more, high color (16 bits, 65,000 colors) or more.

• Depending on the computer you are using, the played back image or sound maystop temporarily, but this does not affect the images or sound copied to yourcomputer.

• Playback software is not installed on your computer.t Install playback software on your computer.

t To display the extension, follow the steps below.1 In the window folder, click [Tools] t [Folder option...] t [View] tab.2Under Advanced Settings, uncheck [Hide file extensions for known file types].3Click [OK].

24

Message Cause/Corrective Action

A:ss:ss/I:ss:ss/P:ss:ss/M:ss:ss/F:ss:ss/X:ss:ss

(Self-diagnosis display)

Self-diagnosis display

When an error occurs the following warning indicators may appear on the LCD screen.

If an error recurs after you repeat corrective action several times, contact SonyCustomer Service or the place of purchase.

A:12:s• CompactFlash-related error has occurred.

t Transfer speed of the CompactFlash may be slow. Be sure that theCompactFlash you are using is the recommended type.

A:19:s• The CompactFlash you are using is not recognized.

t Check the type you are using.I:12:s• Internal error has occurred.

t Turn this unit off and then back on.P:12:s• Internal error has occurred.

t Turn this unit off and then back on.P:21:s• Internal error has occurred.

t Turn this unit off and then back on.M:21:s• Recorded image was not processed correctly.

t Turn this unit off and then back on.F:11:s• Internal error has occurred.

t Turn this unit off and then back on.F:12:s• There is a conflict in the CompactFlash logic structure.

t Move the required data to the computer and reformat the CompactFlash usingthis unit.

F:21:s• Internal error has occurred.


t Turn this unit off and then back on.F:29:s• Firmware is not recorded.F:91:s• Internal error has occurred.


t Turn this unit off and then back on.X:91:s• Internal error has occurred.

t Turn this unit off and then back on.X:99:s• Internal error has occurred.

t Turn this unit off and then back on.

Warning indicators

25

Message Cause/Corrective Action

Caution message

• Displays when inserting an incompatible CompactFlash into this unit.t Use the recommended type of CompactFlash.

• Displays when not formatting a CompactFlash with this unit etc.t Format the CompactFlash using this unit.* When this message is displayed, press the STOP button on this unit to display

the screen for formatting a CompactFlash.

• The CompactFlash you are using may be damaged.t Check the type you are using.

If the above symptoms do not improve, try with a differentCompactFlash.If the above symptoms still do not improve even severalattempts are made, contact your Sony dealer.

• Displays 9999 at the clip number when no more recording is possible.t Delete all of the clips recorded by this unit or format the CompactFlash after

copying clips recorded in the CompactFlash to a computer or other suitablemedia.

26

About i.LINK

The HDV/DV jack provided on this unit is an i.LINK-compliant jack. This section describes the i.LINK standardand its features.

What is i.LINK?i.LINK is a digital serial interface for sending and receivingdigital video, digital audio, and other data between this unitand other equipment equipped with an i.LINK terminal. Youcan also control other equipment using i.LINK.i.LINK-compatible equipment can be connected using ani.LINK cable. Possible applications are operations and dataexchange with various digital AV equipment.When two or more i.LINK-compatible equipment areconnected to this unit, operations and data exchange arepossible with equipment directly connected to this unit andalso with equipment connected to this unit via otherequipment.Note, however, that the method of operation may varydepending on the characteristics and specifications of theequipment to be connected. Also, there are cases whereoperations and data exchange may not be possible even if theconnection is made.

Notes

• Normally, only one device can be connected to this unitusing i.LINK cable. When you connect this unit to HDV/DVCAM (DV)-compliant equipment that allows multipleconnections, refer to the operating instructions of theequipment to be connected.

• i.LINK is an easy-to-remember term for the IEEE 1394proposed by Sony, and is a trademark approved by manycorporations in Japan and overseas.

• IEEE 1394 is an international standard standardized by theInstitute of Electrical and Electronics Engineers.

About the i.LINK baud rateThe maximum baud rate of i.LINK varies depending on theequipment. There are three types.S100 (Approximately 100 Mbps*)S200 (Approximately 200 Mbps)S400 (Approximately 400 Mbps)The baud rate is listed under “Specifications” in the operatinginstructions of individual equipment. It may be indicatednear the i.LINK interface on some equipment.The baud rate may vary from the indicated value when thisunit is connected to equipment with a different maximumbaud rate.

* What is Mbps?Mbps stands for “megabits per second.” It is the volume ofdata that can be sent or received in 1 second. For example, abaud rate of 100 Mbps means that 100 megabits of data canbe sent in 1 second.

To use i.LINK functions of this unitThis unit can be connected to Sony i.LINK-compatibledevices other than camcorders (e.g. VAIO computers).This unit may not be compatible with certain i.LINK videodevices such as digital televisions, DVD recorders/playersand MICROMV recorders/players even if they are equippedwith an i.LINK jack. Before connecting to another device,confirm whether it is HDV/DVCAM (DV) compatible.For precautions on connecting and the availability ofcompatible software applications, refer to the operatinginstructions of the device to be connected.

Notes

• When connecting an i.LINK cable to this unit or acomputer, check the direction of the jack. Forcibly insertingthe jack may damage the terminal or cause a malfunction.

• Always connect the i.LINK cable to the computer first andthen to this unit. Connecting the i.LINK cable to this unitfirst may cause this unit to malfunction because of staticelectricity.

• When using an i.LINK cable to connect this unit to a deviceequipped with an i.LINK jack, switch off the device andremove the power cord from the AC outlet beforeconnecting or disconnecting the i.LINK cable. If the i.LINKcable is connected or disconnected while the power cord ofthe device is connected to the AC outlet, a high-voltagecurrent (8 to 40 V) output from the i.LINK jack of the devicewill flow into this unit and damage it.

• Before changing the HDV/DV format etc. of the camcorder,disconnect the i.LINK cable. Changing the format afterconnecting the i.LINK cable, the video signal may not berecognized correctly.

Required i.LINK cableUse a Sony i.LINK cable.

i.LINK and are trademarks of Sony Corporation.

27

CompactFlash

• A CompactFlash 133x 2 GB or higher is recommended foruse with this unit. (A speed of less than 133x is notguaranteed; space less than 2GB is not guaranteed.)

• When using a CompactFlash for the first time, be sure toformat it with this unit.

• Data may be corrupted or the CompactFlash may not workin the following cases.– If you remove the CompactFlash during data reading/

writing.– If you move the CompactFlash close to a strong magnetic

field.• The CompactFlash may become hot just after use. Handle

with care.• Do not peel the label off the CompactFlash or attach

another label to it.• When storing or carrying the CompactFlash, put it in the

protective case supplied.• Do not get water on the CompactFlash.• Do not apply excessive force on the label surface of the

CompactFlash.• Do not touch the terminal of the CompactFlash with your

hand or any metal object.

Optional CompactFlash

28

Specifications

SystemFile system FAT32CompactFlash 133x 2 GB or more

The capacity is the value when 1GB equals 1 billion bytes.The actual usable capacity maybe slightly less becauseadministrative files etc. areincluded.

File format HDV recording MPEG-2TS(.m2t)

DVCAM/DV recordingAVI-Type1(.AVI)RAW DV (.DV)

Input signalHDV recording/playback

Video: MPEG-2TS1080/60i, 30p, 24p1080/50i, 25p

Audio: 2 CH MPEG 1 AudioLayer2 Stereo (16 bit 48 kHz)(1/2 CH)4 CH MPEG 2 AudioLayer2 Stereo (16 bit 48 kHz)(3/4 CH)

DVCAM/DV recording/playbackVideo: DV embeddedAudio: PCM digital

(12/16 bit, 32k, 48k)Recordable time 2 GB Approx. 9 minutes

4 GB Approx. 18 minutes8 GB Approx. 36 minutes16 GB Approx. 72 minutes

GeneralPower requirement DC 7.2 V (battery pack)

DC 8.4 V (AC adaptor)Power consumption 2.2 WOperating temperature 0 °C to 40 °C (32 °F to 104 °F)Storage temperature –20 °C to +60 °C (–4 °F to +140 °F)Operating humidity 20 % (20 °C) to 90 % (35 °C)

(no condensation)Dimensions

HVR-MRC1 : Approx. 57 × 102 × 34 mm(2 1/4 × 4 1/8 × 1 3/8 in.)

HVR-MRC1+HVRA-CR1: Approx. 77 × 106 × 51 mm(3 1/8 × 4 1/4 × 2 1/8 in.)(including the projecting parts)(w/h/d)

MassHVR-MRC1 : Approx. 130 g (4 oz)HVR-MRC1+HVRA-CR1: Approx. 210 g (7 oz)

(excluding CompactFlash andbattery pack)

Input/output jack i.LINK(IEEE1394 6-pin connector S400)

Optional accessories AC adaptor/chargerAC-VQ1050BBattery packNP-F570/F770/F970

Design and specifications are subject to change withoutnotice.

29

Precautions

On use and care• Do not use or store this unit and accessories in the

following locations.– Anywhere excessively hot or cold. Never leave them

exposed to temperatures above 60 °C (140 °F), such asunder direct sunlight, near heaters or in a car parked inthe sun. They may cause malfunction or becomedeformed.

– Near strong magnetic fields or mechanical vibration. Thisunit may cause malfunction.

– Near strong radio waves or radiation. This unit may notbe able to record properly.

– Near AM receivers and video equipment. Noise mayoccur.

– On a sandy beach or anywhere dusty. If sand or dust getsin this unit, the unit may permanently cause malfunction.

– Near windows or outdoors, where the LCD screen maybe exposed to direct sunlight. This damages the LCDscreen.

– Anywhere very humid.• Operate this unit on DC 7.2 V (battery pack) or DC 8.4 V

(AC Adaptor).• For DC or AC operation, use the accessories recommended

in these operating instructions.• Do not let this unit get wet, for example, from rain or sea

water. If this unit gets wet, it may permanently causemalfunction.

• If any solid object or liquid gets inside the casing, unplugthis unit and have it checked by a Sony dealer beforeoperating it any further.

• Avoid rough handling, disassembling, modifying, physicalshock, or impact such as hammering, dropping or steppingon this unit.

• Keep the POWER switch setting to OFF when you are notusing this unit.

• Do not wrap this unit with a towel, for example, andoperate it. Doing so might cause heat to build up inside.

• When disconnecting the mains lead, pull it by the plug andnot the lead.

• Do not damage the mains lead such as by placing anythingheavy on it.

• Keep metal contacts clean.• If the battery electrolytic liquid has leaked,

– consult your local authorized Sony service facility.– wash off any liquid that may have contacted your skin.– if any liquid gets in your eyes, wash with plenty of water

and consult a doctor.

x When not using this unit for a long time• Use up the battery pack completely before storing it.

LCD screen• Do not exert excessive pressure on the LCD screen, as it

may cause damage.• If this unit is used in a cold place, a residual image may

appear on the LCD screen. This is not a malfunction.• While using this unit, the back of the LCD screen may heat

up. This is not a malfunction.

x To clean the LCD screenIf fingerprints or dust make the LCD screen dirty, it isrecommended you use the LCD Cleaning Cloth (optional) toclean it. When you use the LCD Cleaning Kit (optional), donot apply the cleaning liquid directly to the LCD screen. Usecleaning paper moistened with the liquid.

On handling the casing• If the casing is soiled, clean this unit body with a soft cloth

lightly moistened with water, and then wipe the casingwith a dry soft cloth.

• Avoid the following to avoid damage to the finish.– Using chemicals such as thinner, benzine, alcohol,

chemical cloths, repellent, insecticide and sunscreen.– Handling with above substances on your hands.– Leaving the casing in contact with rubber or vinyl objects

for a long period of time.

30

Getting the best performance from the battery pack

• If the ambient temperature is low, the battery packperformance deteriorates, reducing the operating time. Tomaximize the operating time, the following techniques arerecommended.– Keep the battery pack warm in a pocket, and load it into

the unit immediately before shooting.• The battery is depleted when this unit is in recording

standby or playback pause. Always switch off the powersupply to save energy.

• Have enough battery packs ready to last two or three timesthe expected shooting duration, and test shoot with thembefore the session.

• The battery packs are not waterproof. Be careful not toallow them to get wet.

Indication of remaining battery pack capacityIf the battery pack fails even though the indication suggeststhere is adequate capacity, fully recharge the battery pack.This will correct the remaining capacity indication. However,if the battery pack is used for a long time at high temperature,is left fully charged, or has been very heavily used, theindication may not be correctly restored. In this case, use theindication time as a rough guideline to estimate theremaining capacity.

Battery pack storage• If the battery pack is not used for a long time, to maintain

its performance, it should be fully charged and then fullydischarged with this unit about once a year. Remove thebattery pack from this unit, and store in a cool dry place.

• To fully discharge the battery pack with this unit, leave itpowered on until the battery pack is exhausted.

Battery pack lifetime• The battery pack has a limited lifetime. As it is repeatedly

used over a long time interval, the capacity graduallyreduces. When the operating time is much less than theoriginal value, it is time to replace the battery pack.

• The lifetime varies from one individual battery pack toanother, depending on the pattern of use, and how it hasbeen stored.

Additional information on this product and answers tofrequently asked questions can be found at our CustomerSupport Website.

#1: M1.7 X 2.5 (Black)2-635-562-11

2.5

1.7

#10: M1.7 X 4.0 (Silver)2-599-475-31

1.6

1.7

#6: M1.4 X 1.7 (Silver)2-598-474-01

1.7

1.4

#7: M1.7 X 1.6 (Black)7-627-552-18

#3: M1.7 X 2.5 (Red)2-660-401-01

2.5

1.7

#2: M1.7 X 4.0 (Black)2-635-562-31

4.0

1.7

4.0

1.7

#5: M1.7 X 3.5 (Tapping)(Black)3-080-204-01

3.5

1.7

#4: M1.4 X 2.5 (Tapping)(Dark Silver)3-348-998-81

2.5

1.4

#12: M1.7 X 5.0 (Tapping)(Black)3-080-204-21

1.7

#9: M1.7 X 5.0 (Tapping)(Silver)3-078-890-21

5.0

1.7

#14: M1.7 X 2.5 (Silver)2-599-475-11


2.5

1.7



3.5

1.7

4.0

1.7

5.0

2.5

#17: M1.7 X 1.5 (Silver)2-586-389-01

2.5

1.7

#15: M1.4 X 1.5 (Silver)3-062-214-01

1.5

1.4 1.4

#16: M1.4 X 2.5 (Silver)2-586-337-01

1.5

3.5

1.7 2.2

#18: M1.4 X 2.5 (Silver)2-635-591-21

2.5

1.4

#19: M1.2 X 4.0 (Tapping)(Red)3-086-156-21

4.0

1.2

#20: M1.4 X 3.0 (Silver)2-635-591-31

3.0

1.4

HARDWARE LIST (1/7)

HARDWARE LIST (2/7)

#21: M1.4 X 3.0 (Black)2-662-396-21

3.0

1.4


1.7

5.0

1.7

5.5

#23: M1.7 X 4.0 (Tapping)(Black)3-080-204-11

4.0

1.7

#24: B1.7 X 5.5 (Tapping)(Black)4-679-805-11

#25: M1.7 X 3.0 (Black)2-635-562-21

3.0

1.7

#26: M1.4 X 2.0 (Silver)2-635-591-11

2.0

1.4

#27: M1.4 X 2.0 (Black)2-662-396-11

2.0

1.4


1.4

4.0

#29: M1.4 X 2.5 (Black)2-662-396-01

#31: M3.0 X 4.0(Silver)2-102-434-01

2.5

1.4

#30: M1.2 X 3.5 (Tapping)(White)3-086-156-11

3.5

1.2


#33: M3.0 X 6.0 (Silver)3-077-331-21


#34: M3.0 X 8.0 (Black)3-077-331-41

#36: M3.0 X 6.0 (Silver)4-886-821-11

#37: M2.0 X 6.0 (Tapping)(Black)3-080-206-31



#39: M2.6 X 5.0 (Tapping)(Black)7-685-791-09

4.0

3.0

4.5

2.0

6.0

3.0

8.0

3.0 4.0

6.0 6.0

3.0

6.0

2.0

20.0

3.0

4.0

2.0

5.0

2.6

HARDWARE LIST (3/7)


8.0

3.0


2.0

4.0

#43: M1.7 X 4.0 (Red)2-660-401-31

4.0

1.7

#46: M1.7 X 3.0 (Red)2-660-401-11

#45: M1.4 X 2.5 (Silver)2-587-151-01


3.0

1.4


3.0

1.7

3.0

1.7

2.5

1.4

#48: M1.7 X 2.5(Silver)3-973-497-91

2.5

1.7

#49: M2.0 X 4.0(Black)2-630-005-31

#50: M2.0 X 3.0(Red)2-891-494-11

#51: M2.0 X 2.5 (Silver)3-073-686-01

#54: M1.75 X 6.0 (Tapping)(Black)3-318-203-11

#53: M2.0 X 5.0 (Tapping)(Black)3-080-206-21

#55: M2.0 X 4.0(Silver)2-655-582-11

#52: M2.0 X 4.0 (Tapping)(Black)3-080-206-11

#56: M2.0 X 3.5(Silver)3-067-187-11

4.0

2.0

3.0

2.0

2.5

2.0

5.0

2.0

4.0

2.0

6.0

1.75

4.0

2.0

3.5

2.0

#57: M1.7 X 4.0(Black)7-627-852-18

4.0

1.7


6.0

2.0


#60: M2.6 X 5.0(Black)3-061-062-11

5.0

2.0

5.0

2.6

HARDWARE LIST (4/7)

#61: M3.0 X 10.0(Black)7-682-549-09

10.0

3.0

#62: M2.0 X 3.0(Silver)3-080-202-21

3.0

2.0

#63: M5.0 X 12.5(Black)3-060-811-21

12.5

5.0


5.0

1.7

#65: M1.4 X 3.5 (Silver)2-635-591-01

3.5

1.4

#66: M1.4 X 1.4 (Silver)2-635-591-41

1.4

1.4

#71: M1.4 X 2.0 (Red)3-208-537-01

2.0

1.4

2.0

1.4

2.0

1.4

#67: M1.4 X 2.0 (Silver)3-389-523-16

2.0

1.4

#68: M1.7 X 4.0 (Silver)2-655-581-01

4.0

1.7

#72: M1.4 X 2.0 (Silver)4-663-621-41

2.0

1.4

#69: M1.7 X 3.0 (Silver)2-599-475-21

3.0

1.7

#70: M1.7 X 5.0 (Silver)2-599-475-41

5.0

1.7

#75: M1.7 X 3.5 (Tapping) (Silver)2-666-551-01


#73: M1.2 X 4.0 (Tapping) (Black)3-086-156-61


#78: M1.4 X 3.5 (Red)3-208-537-11

#79: M1.4X 2.0(Silver)2-587-151-11

#80: M1.4X 2.0 (Black)3-279-411-01

6.0

1.7

3.5

1.7

4.0

1.7

4.0

1.2


5.0

1.2

3.5

1.4

HARDWARE LIST (5/7)

#81: M1.7 X 2.5 (Silver)2-515-756-01

2.5

1.7

#82: M1.4 X 1.4 (Silver)3-272-251-01

1.4

1.4

#83: M1.7 X 7.0 (Tapping) (Black)3-080-204-41

#84: M2.0 X 3.0 (Silver)3-072-453-11

#85: M1.7 X 2.5 (Black)2-515-483-11


4.0

1.7

#87: M1.6 X 5.3 (Black)2-689-328-01

5.3

1.6


5.9

1.6


5.0

2.0

#90: M1.7 X 3.0 (Silver)3-271-395-01

3.0

1.7


#92: M2.0 X 3.9 (Black)3-268-954-01

3.9

2.0


#94: M1.7 X 4.0 (Black)2-515-483-31

1.7

7.0 3.0

2.0

2.5

1.7

4.0

1.7

3.5

1.7

3.5

1.7

#95: M3.0 X 8.0 (Tapping) (Black)7-685-646-79

8.0

3.0


6.0

2.5

#96: M1.4 X 2.5 (Silver)2-587-151-21

2.5

1.4

#97: M1.4 X 2.5 (Black)2-662-396-31

2.5

1.4

#98: M3.0 X 8.0 (Silver)3-077-331-01

8.0

3.8

#100: M2.0 X 6.0 (Black)3-080-203-51

6.0

2.0

HARDWARE LIST (6/7)

#101: M2.0 X 5.0 (Silver)7-621-555-39

5.0

2.0

#107: M2.0 X 5.0 (Silver)3-032-750-01

5.0

2.0

#108: M1.7 X 3.0 (Tapping) (Black)2-695-430-01

#111: M1.7 X 4.0 (Tapping) (Black)2-887-124-01

#102: M2.6 X 8.0 (Black)7-621-284-30

8.0

2.6

#105: M2.0 X 4.0 (Red)2-891-494-31

#106: M2.0 X 6.0 (Black)3-713-786-11

#103: M2.6 X 10.0 (Silver)7-685-794-09

10.0

2.6

#104: M3.0 X 8.0 (Black)7-682-548-09

8.0

3.0

6.0

2.6

4.0

2.0

6.0

2.0

3.0

1.7

#109: M1.7 X 3.0 (Black)2-515-483-21

3.0

1.7

3.0

2.0

#110: M2.0 X 3.0(Black)2-630-005-21

4.0

1.7


5.5

2.0

#112: M1.4 X 5.0 (Black)2-178-410-11

5.0

1.4

#113: M1.7 X 5.0 (Black)2-635-562-41

5.0

1.7


1.4

3.5


3.5

2.0


#118: M1.4 X 2.0 (Black)2-655-580-01

4.5

1.7

2.0

1.4

#119: M2.6 X 5.0 (Black)7-627-556-58

5.0

2.6

#120: M2.6 X 6.0 (Silver)7-621-770-67

HARDWARE LIST (7/7)


#123: M4.0 X 8.0 (Black)7-682-561-09

8.0

4.0

6.0

3.0

#122: M3.0 X 6.0 (Black)7-682-547-09

4.0

2.0

2.0

1.7

#124: M1.7 X 2.0 (Silver)2-599-475-01

Revision History

Reverse

HVR-MRC1

Ver.

1.0

1.1

1.2

Date

2008.01

2008.06

2009.03

History

Official Release

Revised-1(A1 DI08-162)

Revised-2(A2 DI08-386)

Contents

—

• Change of Repair PartsS.M. revised: Page 5-5, Page 5-6, Page 5-7

• Change of Repair PartsS.M. revised: Page 5-2, Page 5-3, Page 5-4,

Page 5-5, Page 5-7

S.M. Rev.issued

—

Yes

Yes

985226613.pdf

hvr-mrc1 - espec

Documents