hvac boq r1- 29-08-2013 (2)

For Employer of 47 For Contractor

PROJECT: Construction of Expansion of Yashoda Hospital- Phase-1

GRAND SUMMARY

S No Item Supply Installation Total Remarks

1 CHILLED WATER AIR CONDITIONING SYSTEM

2 DX SYSTEM

3 VENTILATION SYSTEM

4 BASEMENT VENTILATION SYSTEM

TOTAL AMOUNT

In Words:


Project : Expansion of Yashoda Hospital- Phase-1

Client:Yashoda Hospitals

Architect: SMJ Design Inc

PMC: KP Management Associates

MEP Consultant: Synergy Infra Consultant Pvt Ltd BOQ

Interior Consultant: M/s. Prasad Badle Architects

Location: Somajiguda-Hyderabad Date: 30-Aug-2013 Rev: R0

S.No DESCRIPTION UNIT QTYRATE AMOUNT

Supply Installation Supply Installation

A CHILLED WATER AIR CONDITIONING SYSTEM

1.0

i

ii

iii

iv

v

1.0 a Nos. 3.00

Package: Supply,Installation,Testing and Commissioning of HVAC and Ventilation System

Installation of Water Cooled Turbo Chillers of below specified actual cooling capacity with following technical parameters complying with the technical specifications. Evaporator with 54°F inlet water and 44°F outlet water and fouling factor of 0.0001 FPS units. The chiller shall be with single / twin independent refrigerant circuits, having R-134a / R-407c / R-410A / Eco friendly refrigerant. The scope shall include the complete packaged chiller with hermetic / semi-hermetic compressor, condenser, chiller , refrigerant controls & valves, vibration isolators, refrigerant piping and wiring, accessories as required, automatic and safety controls mounted in central console panel and all mounted on a epoxy coated steel frame with spring isolators complete as per specifications, suitable for outdoor exposed duty conditions and complete assembly mounted on common base frame / skid, painted with anti corrosive paint. Motor shall be suitable for 415+/-10,50 cycles, 3 phase ac supply. Following accessories shall be also included in the scope of supply of chillers.

Factory Supplied Electrical starter panel with unit mounted power isolator and BMS ready Microprocessor Panel.

Chillers starters shall be close transition start delta if only as per manufacturer standard. However, the Chiller should be able to operate from 10 % capacity to 100 % in stepless / infinite steps and this factor should be able to be monitored / controllable from the End User's BMS System for User based HVAC Load Optimisation requirements

Counter flanges / victaulic couplings for cooler and condenser water piping connections.

Restrained spring type of Vibration isolators to be provided or as recommended by manufacturer for complete structurual isolation

Acoustic jacketing of the chiller to meet the noise level of less than 70 dB(A) at 3 m from unit

300 TR Capacity Turbocor as per above specifications.












1.0 b

Nos. 1.00

2.0

2.1 aNos. 3.00

2.2 aNos. 3.00

2.2 b

Lot 1.00

Chilled Water Secondary pumps VFD Compatible Panel Incoming : 160A 35KA TP MCCB with Neutral link- 1noBus bars : 160A TPN Aluminum Bus bars – 1SetOutgoings:

Metering :

SITC of Standalone Chiller Plant Manager with Visual Display Console and with complete connectivity to Client's BMS on OPEN protocol to be included(Prior Approval to be taken from BMS Vendor to suite the Protocol, preferably by MODBUS).

SITC and handing over of Split coupled Vertical inline type chilled water circulation pump set mechanical seal to deliver the following flow rate with flexible connection inlet & outlet including necessary Pressure Gauges with siphon & cock, insulation etc.,complete. As per Specifications. The pump motor shall suitable for 415± 10% volts, 50 cycles, 3 phase AC power supply.

Primary chilled water pumps of 720 USGPM at 15 MWC head (2Working+1Stand BY)

Secondary chilled water pumps of 720 USGPM at 25 MWC head (with motor suitable to operate on variable frequency drive). (2 Working+1Stand BY)

SITC of Stand alone Chilled Water Secondary Pumps logic controller, 2 DP transmitters, 3 nos. individual VFDs for all Secondary pumps with required software and hardware to connect to Client's BMS integration, in an IP 54 enclosure and all related control wiring of 400 RMT length from Controller Panel to DP Transmitters (2No's) in MS conduit along the Chilled Water pipeline and all related control wiring.

NOTE: The scope includes Electrical cabling(15 Rmt each ) from the VFD Panel to respective Secondary pumps.

Bypass star delta starter suitable for 25kw -3 No's for Secondary Pumps (VFD's considered in Secondary pumps)












i) 0 - 500V Digital Voltmeter with Selector switch -1setii) 0 – 160A Digital Ammeter with Resin cast Ctsand selector switch-1setiii) CT operated Multi function Meter with RS 485 connectivity-1setiv) LED type Phase indication lamps withindividual MCB control and toggle switches - 1set

2.3 a Condenser cooling water pumps of 1440 USGPM at 45 MWC head.Nos. 3.00

3.0

3.0 a Cooling Tower (Cap: 360 TR) & Flow rate of 1440 USGPM Nos. 3.004.0 Air Handling Units

SITC of Single or multiple cell Induced draft cooling towers to suit heat rejection of below specified Chiller heat rejection while working at 95.5 °F inlet water and 88 °F outlet water designed at an ambient wet bulb temperature of 80 °F taking a cooling water flow of 1440 usgpm as per technical specifications. The scope shall include complete FRP casing louvers for intake air with required internal structural supports in galvanized steel, internal piping distribution, axial flow propeller fan with FRP or die pressure die cast aluminum blades, driven by TEFC, IPFF, outdoor application Eff1 motor.












4.1

a. 3200 CFM / 6.0 TR (CT OT's) Nos. 2.00

SITC of Ceiling suspended Air Handling Units of below specified duty conditions with Full Face Cooling Coil, DIDW backward curved Fan with Eff1 TEFC IP 55 drive motor, in thermal break profile casing. The Air Handling Unit shall be in double skin casing of 50 mm thick insulated panels with 0.8 mm thick prepainted outer and GS inner skin, Fan & Motor assembly mounted on aluminum frame resting on spring isolators, sized with Full Face AHRI certified 8Row,12 FPI Chilled Water cooling coil with max. 1.50 M/s Coil Face Velocity, and having all round insulated drain pan of 1.0 mm thick SS-304, fire retardant flexible canvas, AHU outlet damper, safety door limit switches, internal belt guard, internal service light, UV light inside AHU etc, all as per specifications and with Noise level below 65 dB levels. The Fan Static shall be 150 MM WG at below specified CFM and the filteration level provided within the AHU shall be MERV 7 + MERV 13 + MERV 17. The AHU shall be designed for 24 Hours operation duty conditions and shall have suitable VFD for the motor.

The scope includes suitable Power & Control Cables of 10 RMT each from floor electrical panel to AHU starter panel then to the respective AHU motor.

The AHU shall be designed for 24 Hours operation duty conditions and the AHU Motor shall be VFD Compatible and the AHU shall have controls for the motor's VFD to be controlled through time dependent Air Velocity Settings including hardware & wiring and shall be possible to be monitored / controlled through Client's BMS System.












4.2

a. 1200 CFM / 6.0 TR Sets 1.00b. 1400 CFM / 7.0 TR Sets 1.00c. 1800 CFM / 9.0 TR Sets 1.00

5.0 Fan coil units & Chilled Water Cassette Units

SITC of Ceiling Suspended Treated Fresh AIr Units of below specified duty conditions with Full Face Cooling Coil, DIDW backward curved Fan with Eff1 TEFC IP 55 drive motor, in thermal break profile casing. The Air Handling Unit shall be in double skin casing of 25 mm thick insulated panels with 0.8 mm thick prepainted outer and GS inner skin, Fan & Motor assembly mounted on aluminum frame resting on spring isolators, sized with Full Face AHRI certified 8 Row 12 FPI Chilled Water cooling coil with max. 2.5 M/s Coil Face Velocity, and having all round insulated drain pan of 1.0 mm thick SS-304, fire retardant flexible canvas, AHU outlet damper, safety door limit switches, internal belt guard, internal service light, UV light inside AHU etc.all as per specifications and with Noise level below 65 dB levels. The Fan Static shall be 75 MM WG at below specified CFM and the filteration level provided within the AHU shall be MERV 7 + MERV 13 + MERV 17.

The scope includes suitable Power & Control Cables of 10 RMT each from floor electrical panel to AHU starter panel then to the respective AHU motor.

The AHU shall be designed for 12 - 16 Hours operation duty conditions and the AHU Motor shall be VFD Compatible and the AHU shall have controls for the motor's VFD to be controlled through time dependent Air Velocity Settings including hardware & wiring and shall be possible to be monitored / controlled through Client's BMS System.












5.1

a) 1.0 TR / 400 CFM Nos. R/ob) 1.5 TR / 600 CFM Nos. 48.00c) 2.0 TR / 800 CFM Nos. 6.00d) 3.0TR / 1200 CFM Nos. R/o

5.2

a) 1.0 TR / 400 CFM Nos. R/ob) 1.5 TR / 600 CFM Nos. 106.00c) 2.0 TR / 800 CFM Nos. 39.00d) 3.0TR / 1200 CFM Nos. 17.00d) 4.0TR / 1600 CFM Nos. R/o

6.0 Pressure Monitoring System

Nos 10.00

7.0 Chilled water piping

SITC of Hide Away Chilled Water Fan Coil Units with inlet & outlet SS Shut off Ball valves,Strainer, Proportional Control Solenoid Valve, 3 speed Fan controller, Wall Mounted Electronic Digital Display Thermostat with BMS connectivity, Canvas connection, Required Control wiring, required power & control cables etc. with Max 40 dB sound level & with cordless remote.

SITC of Hide Away Chilled Water Ceiling Cassettes with inlet & outlet SS Shut off Ball valves,Strainer, Proportional Control Solenoid Valve, 3 speed Fan controller, Wall Mounted Electronic Digital Display Thermostat with BMS connectivity,Required Control wiring, required power & control cables etc. with Max 40 dB sound level & with cordless remote.

SITC of Wall Mountable / Standalone Magnehelic Gauges for displaying room differential pressure 0-10 mm with wall mounted / stand alone Gauge Panel in SS & with related sensors and accessories and BMS Compatibility for remote pressure monitoring.












7.1

a) 300mm dia (minimum 6mm thick ) Rmt 150.00b) 250mm dia (minimum 6mm thick ) Rmt R/oc) 200mm dia (minimum 6mm thick ) Rmt 150.00d) 150mm dia Rmt 40.00e) 125mm dia Rmt 10.00f) 100mm dia Rmt 15.00g) 80mm dia Rmt 150.00h) 65mm dia Rmt 470.00i) 50mm dia Rmt 400.00j) 40mm dia Rmt 640.00k) 32mm dia Rmt 860.00l) 25mm dia Rmt 2200.00

m) 20mm dia Rmt R/o8.0 Condenser water piping

a) 350mm dia Rmt 140.00b) 300mm dia Rmt R/o

SITC of the following heavy Class "C" MS Pipes and fittings confirmed to IS 1239 & IS 3589 as specifications,cut to required lengths and installed with all welded joints, providing and fixing in position neccessary fittings like bends, elbows, tees, reducers, mating flanges & sockets and insulation with 50 mm thick, 18 kg/cum density TF quality expanded polystyrene pre-formed pipe sections upto 80 mm dia pipes and 75 mm thick insulation for above 80 mm dia pipes finished with air-tight leak-proof alkathene vapour barrier, 22 G GI chicken wire mesh wrapping and 26 G Alm sheet cladding.

SITC of the following heavy Class "C" MS Pipes and fittings confirmed to IS 1239 & IS 3589 as specifications, cut to required lengths and installed with all welded joints, providing and fixing in position neccessary with fittings like bends, elbows, tees, reducers, mating flanges & sockets and approved color 2 coat painting.












c) 250mm dia Rmt 200.00d) 200mm dia Rmt R/oe) 150mm dia Rmt 20.00f) 125mm dia Rmt R/og) 100mm dia Rmt 20.00h) 80mm dia Rmt R/oi) 50mm dia Rmt 40.00

9.0

a) 300mm dia (gear operated) Nos. 3.00b) 250mm dia (gear operated) Nos. 18.00c) 200mm dia (gear operated) Nos. 23.00d) 150mm dia Nos. R/oe) 125mm dia Nos. R/of) 100mm dia Nos. 3.00g) 80mm dia Nos. 8.00h) 65mm dia Nos. 10.00

SITC of Extended stem Butterfly valves of following sizes with extended stem, wafer type / lug type construction, bolts, supports etc as per specifications suitable for 16 Kg/cm2 pressure. (The valves used in the chilled water pipeline shall be insulated with loose TF quality thermocole for a layer of 50 mm thickness and finished as per similar specifications of chilled water piping insulation).












i) 50mm dia Nos. 7.00j) 40mm dia (ball valve) Nos. 10.00k) 32mm dia (ball valve) Nos. 3.00l) 25mm dia (ball valve) Nos. R/o

m) 20mm dia (ball valve) Nos. R/o10.0

a) 300mm dia Nos. R/ob) 250mm dia Nos. 6.00c) 200mm dia Nos. 4.00d) 150mm dia Nos. R/oe) 125mm dia Nos. R/of) 100mm dia Nos. R/og) 80mm dia Nos. 4.00h) 65mm dia Nos. 5.00i) 50mm dia Nos. R/oj) 40mm dia Nos. 5.00k) 32mm dia Nos. R/ol) 25mm dia Nos. R/o

m) 20mm dia Nos. R/o

SITC of Manual Balancing valves for following sizes with flanged type construction, bolts, supports etc. as per specifications suitable for 16 Kg/cm2 pressure. The valves shall be insulated with loose TF quality thermocole for a layer of 50mm thickness. The insulation to be covered by 24 G aluminum sheet box.












11.0

a) 100mm dia line Nos. R/ob) 80mm dia line Nos. R/oc) 65mm dia line Nos. R/od) 50mm dia line Nos. R/oe) 40mm dia line Nos. 5.00f) 32mm dia line Nos. R/og) 25mm dia line Nos. R/o

12.0

a) 250mm dia Nos. R/ob) 200mm dia Nos. 6.00c) 150mm dia Nos. 3.00d) 125mm dia Nos. R/o

SITC of 2-way Modulating Valve with Spring-Return Actuator with Open / Close Feedback signal & BMS connectivity option on Open / MODBus / BACnet protocol & local Wall Mounted Digital Display Thermostats for Mixing Valve Temperature Control and Extended Bracket to clear insulation for Actuator and related control cabling in flexible PVC conduit. (The AHU Starter Panel shall have a 24 V AC/DC supply available for this purpose) for the following line sizes. The valves shall be insulated with loose TF quality thermocole for a layer of 50mm thickness and finished as per chilled water insulation specifications. The scope includes suitable Power cable & control cable of each 10 RMT from AHU starter panel to actuator and BMS connectivity for remote monitoring / controlling.

SITC of Dual plate wafer type Check valves for following sizes with SS / Bronze plate, bolts, supports etc. as per specifications suitable for 16 Kg/cm2 pressure. The valves shall be insulated with loose TF quality thermocole for a layer of 50mm thickness and finished as per chilled water insulation specifications.












13.0

a) 250mm dia Nos. 3.00b) 200mm dia Nos. 6.00c) 150mm dia Nos. R/od) 100mm dia Nos. R/oe) 80mm dia Nos. R/of) 65mm dia Nos. R/og) 50mm dia Nos. R/oh) 40mm dia Nos. 5.00i) 32mm dia Nos. R/oj) 25mm dia Nos. R/ok) 20mm dia Nos. R/o

14.0

a) 250mm dia Nos. 6.00b) 200mm dia Nos. 3.00b) 150mm dia Nos. R/oc) 125mm dia Nos. R/o

15.0 SITC of Automatic Air Vents on extended nipples with isolation valves.a) 1/2 " dia. Nos. 50.00

SITC of Y type strainers with SS Mesh for following sizes with matching flanges, bolts, supports etc. The strainers shall be insulated with loose TF quality thermocole for a layer of 50mm thickness and finished as per chilled water insulation.

SITC of Motorized ON/OFF butterfly valves with Actuators with ON / OFF Feedback for following sizes with Extended Stem, matching bolts, supports etc. complete with required 240 / 12 V transformers, control wiring from chillers etc. as per specifications. The valves shall be suitable for BMS integration on Open / MODBus BACnet protocol. The valves shall be insulated with loose TF quality thermocole for a layer of 50mm thickness and finished as per chilled water insulation specifications.












16.0

a) 250mm dia Sets 12.00b) 200mm dia Sets 18.00c) 150mm dia Sets R/od) 125mm dia Sets R/o

17.0 SITC of Dial type Pressure gauges with siphon and ball valveSets 456.00

18.0Sets 444.00

19.0 SITC of Paddle type water flow switches for chiller side Sets 6.0020.0 DRAIN PIPING:

a) 25mm dia. Rmt 950.00b) 32mm dia Rmt 350.00c) 40mm dia Rmt 250.00d) 50mm dia Rmt 180.00e) 65mm dia Rmt 90.00

21.0Set 1.00

22.0

Nos 1.00

SITC of Rubber expansion joints for following sizes with double bellows, tie rods and MS flanges. The REJs shall be insulated with flexible nitrile rubber insulation of 32 mm thickness in two layers.

SITC of Dial type Thermometers with required length of thermowells & immersion stems

SITC of Condensate drain piping for following sizes of class B GI pipes from AHU drain connections to nearest floor drain complete with fittings, U-traps etc. The insulation shall be similar to that of the chilled water piping.

SITC of insulated 1000 LTRS HDPE Expansion tank with all required connections & valves

SITC of digital display Water flow meter suitable for BMS connectivity with necessary accessories in chilled Water Main header












23.0

Sets 1.00

24.0

Sets 1.00

25.0 AIR DISTRIBUTION25.1

a) 24 G Ducting (upto 750 mm) 1300.00b) 22 G Ducting (751 mm to 1500 mm) 150.00c) 20 G Ducting (1501 mm to 2200 mm) 20.00

25.2 18 G Plenum 30.0025.3 SITC of Round Flexible duct

a) 100 mm Dia R/ob) 150 mm Dia R/o

SITC of Air separator on the return water header located at the primary pump suction and suitable for 1440 US GPM water flow, 300 mm dia inlet & outlet. The separator should be complete with high capacity air vent, service valve, non return valve, valve connection for makeup water inlet, flanges etc.

SITC of Chemical Dosing Sets & Softner to meet the water quality requirements for Cooling tower Water including a dosing pump, with interconnecting tubing and foot valve, chemical storage tank of 25 liters, ionization sensor and required controls.

SITC of Factory fabricated GSS ducting complete with splitters, turning vanes, access doors, supports etc. as per specifications. Factory fabricated ducting to be as per SMACNA standards for the sheet metal thicknesses as given below.

m2

m2

m2

m2

m2

m2












c) 200 mm Dia 80.0025.4

a) 18 G ducting R/ob) 20 G ducting R/o

25.510.00

25.6

a) Bare fire damper 10.00b)

Nos. 30.00

25.7R/o

25.8R/o

25.95.00

25.10 SMT 20.00

25.11 SMT 15.00

25.12 SITC of Al. Powder coated Continuous Grill of following sizes

a. 4" Continuous Grill RMT R/ob. 6" Continuous Grill RMT 350.00

m2

SITC of Aluminum ducting complete with splitters, turning vanes, access doors, supports etc. as per specifications.

m2

m2

SITC of Multi blade volume control dampers of opposed blade type in GSS construction with suitable links, levers and quadrants for proper balancing of the air distribution system.

m2

SITC of Motorized fire and smoke dampers with minimum 90 min fire rating UL 555 listed with fire and smoke sensor and factory wired control panel, having extended sleeve of 450 mm. The damper actuator and total wiring for actuator and control panel shall be rated to withstand 250 deg C for 2 hours.

m2

Motorized actuator of suitable power rating and torque rating for above dampers along with connectivity for BMS.

SITC of 4 way supply air square ceiling diffusers in extruded aluminum construction having powder coated finish with integral black painted opposed blade dampers

m2

SITC of 4 way return air square ceiling diffusers in extruded aluminum construction without dampers m2

SITC of Fresh air intake louvers of powder coated extruded aluminum construction with all side flanges having integral insect screen. m2

SITC of Supply Air Grill to suit gyp and grid false ceiling with AL extruded black colored collar damper

SITC of Return Air / Exhaust Air Grill to suit gyp and grid false ceiling with AL extruded black colored collar damper












c. 8" Continuous Grill RMT R/o25.13 No's 100.00

26.0 Insulation26.1

650.00

26.2

R/o

26.3R/o

26.4

250.00

26.5

R/o

26.6

560.00

27.0Lot 1.00

28.0

SITC of Exhaust Air Grill(Round type) to suit gyp and grid false ceiling with AL extruded black colored collar damper for toilets

SITC of Duct thermal insulation with 25 mm thick blanket type fiberglass with factory laminated aluminum foil with density 24 kg/m3 and edges covered with al tape and then covered with 22 G GI chicken wire mesh as per technical specifications.

m2

SITC of Duct thermal insulation with 50 mm thick blanket type fiberglass with factory laminated aluminum foil with density 24 kg/m3 and edges covered with Al Tape and covered with 22 G GI Chicken wire mesh as per technical specifications m2

SITC of Duct Thermal Insulation applied outside of the duct work with Alm. backed Closed cell nitrile/ Cross linked foam duly fixed with adhesive, 22 G chicken wire mesh. (25 mm Thickness)

m2

SITC of Duct acoustic insulation with 12 mm thick rigid board fiberglass of 48 kg/m3 density, and completely covered with RP tissue and 26 G aluminum perforated sheet mechanically bonded with 6 mm fasteners. m2

SITC of Duct Accoustic Insulation applied inside of the duct work with Alm. backed OPEN cell nitrile/ Cross linked foam duly fixed with adhesive and GI nuts & bolts.(19 mm thickness) m2

SITC of Under deck insulation with 50mm thick TF quality expanded polystyrene rigid boards, and bottom completely covered with AL Foil covering and then cross binding with 22 G GI chicken wire mesh, for fixing and brass screws and washers as required. m2

SITC of MS Support structures for chilled water piping, condenser water piping, on terrace, floors, etc.

AMC (material & labour) year wise (for 5 years) after the standard 24 month from commissioning warranty period.












SUB TOTLA FOR CHILLED WATER BASED AIR SYSTEMB DX SYSTEM

1.0 Air Handling Units1.1

a. 3800 CFM / 8.5 TR (FOR MRI) Nos. 1.00b. 1600 CFM / 4.0 TR (FOR CTSCAN) Nos. 1.00

SITC of Ceiling suspended Air Handling Units of below specified duty conditions with Full Face Cooling Coil, DIDW backward curved Fan with Eff1 TEFC IP 55 drive motor, in thermal break profile casing. The Air Handling Unit shall be in double skin casing of 50 mm thick insulated panels with 0.8 mm thick prepainted outer and GS inner skin, Fan & Motor assembly mounted on aluminum frame resting on spring isolators, sized with Full Face AHRI certified 6 Row 12 FPI Direct expansion cooling coil with max. 2.5 M/s Coil Face Velocity, and having all round insulated drain pan of 1.0 mm thick SS-304, fire retardant flexible canvas, AHU outlet damper, safety door limit switches, internal belt guard, internal service light, UV light inside AHU etc, all as per specifications and with Noise level below 65 dB levels. The Fan Static shall be 75 MM WG at below specified CFM and the filteration level provided within the AHU shall be MERV 7 + MERV 13.

The scope includes suitable Starter Panel with VFD & Power & Control Cables of 10 RMT each from floor electrical panel to AHU starter panel then to the respective AHU motor.

The AHU shall be designed for 12 - 16 Hours operation duty conditions and the AHU Motor shall be VFD Compatible and the AHU shall have controls for the motor's VFD to be controlled through time dependent Air Velocity Settings including hardware & wiring and shall be possible to be monitored / controlled through Client's BMS System.












1.2

a. 3200 CFM / 7.0 TR Nos. 3.00b. 3800 CFM / 8.0 TR Nos. 4.00

SITC of Ceiling suspended Air Handling Units of below specified duty conditions with Full Face Cooling Coil, DIDW backward curved Fan with Eff1 TEFC IP 55 drive motor, in thermal break profile casing. The Air Handling Unit shall be in double skin casing of 50 mm thick insulated panels with 0.8 mm thick prepainted outer and GS inner skin, Fan & Motor assembly mounted on aluminum frame resting on spring isolators, sized with Full Face AHRI certified 8Row,12 FPI Direct expansion cooling coil with max. 1.50 M/s Coil Face Velocity, and having all round insulated drain pan of 1.0 mm thick SS-304, fire retardant flexible canvas, AHU outlet damper, safety door limit switches, internal belt guard, internal service light, UV light inside AHU etc, all as per specifications and with Noise level below 65 dB levels. The Fan Static shall be 150 MM WG at below specified CFM and the filteration level provided within the AHU shall be MERV 7 + MERV 13 + MERV 17. The AHU shall be designed for 24 Hours operation duty conditions and shall have suitable VFD for the motor.

The scope includes suitable Power & Control Cables of 10 RMT each from floor electrical panel to AHU starter panel then to the respective AHU motor & to the Strip heaters and humidifier.

The AHU shall be designed for 24 Hours operation duty conditions and the AHU Motor shall be VFD Compatible and the AHU shall have controls for the motor's VFD to be controlled through time dependent Air Velocity Settings including hardware & wiring and shall be possible to be monitored / controlled through Client's BMS System.












2.0

a. 8.5 TR Nos 8.00b. 5.5 TR Nos 1.00

3.0

a. 1.0 TR / 400 CFM Nos. 1.00b. 1.5 TR / 600 CFM Nos. 3.00c. 2.0 TR / 800 CFM Nos. 3.00d. 3.0TR / 1200 CFM Nos. 2.00e. 4.0TR / 1600 CFM Nos. R/o

4.0 REFRIGERANT PIPING4.1

a. 3/8" dia(9.375) RMT 150.00b. 5/8" dia(15.8) RMT 350.00c. 7/8" dia(22.2) RMT 20.00d. 1 1/8” dia(28.6 mm) RMT 180.00

SUB TOTAL FOR DX SYSTEMc) VENTILATION SYSTEM

1.0

a) 900 CFM / 25 mmWC Sets 6.00b) 1000 CFM / 25mmWC Sets 4.00

SITC of following capacity Condensing Units including refrigerant connections with expansion valves & necessary valves etc., complete

SITC of the following capacities of 4Way cassette with complete with compressor, condenser, evaporator, Remote, Control cable & Power Cable, supports, etc. as per the specifications.

SITC of 16 SWG hard drawn copper piping for ductable split units of the following sizes including 19mm thick nitrile tube insulation, supports, clamping, fittings, etc.

SITC of Cabinet type Fresh Air Fan of double single skin insulated casing, DIDW centrifugal backward curved fan, Eff 1 TEFC drive motor, drive set, base frame, vibration isolators, flexible connection following capacities.












c) 3000 CFM / 25 mmWC Sets 1.002.0

a) 100 CFM / 25 mmWC Sets 6.00b) 200 CFM / 25 mmWC Sets 1.00c) 300 CFM / 25 mmWC Sets 6.00d) 500 CFM / 25 mmWC Sets 5.00e) 600 CFM / 25 mmWC Sets 4.00

3.0 a

a) 50 CFM, 6.5 mm WG Nos 56.00b) 100 CFM, 6.5 mm WG Nos 2.00c) 200 CFM, 6.5 mm WG Nos R/od) 250 CFM, 6.5 mm WG Nos R/o

SUB TOTAL FOR VENTILATION SYSTEMD) BASEMENT VENTILATION SYSTEM1 JET FANS

1.1 No's 40.00

2 SMOKESPILL TUBE AXIAL FANS FOR EXHAUST & FRESH AIR

SITC of Cabinet type Exhaust Air fan of double single skin insulated casing, DIDW centrifugal backward curved fan, Eff 1 TEFC drive motor, drive set, base frame, vibration isolators, flexible connections.for following capacities.

SITC of Exhaust Fans (Wall Mounted with Mounting Frame & Insect barrier SS mesh) (Max 60 Db) of following capacities for Patient Rooms Toilets.

Supply,Installation,Testing & Commissioning of Induction 300mm Dia JETVENT fans with as per Technical specifications

Supply erection testing and commissioning & handing over of Long Cased Axial fans for exhaust air of the following capacities, containing DIDW blower along with suitable size motor mounted on a M.S frame fan pulley, motor pulley.with all required supports etc.,complete












2.1 No's 4.00

2.2 No's 8.00

2.3 LS 1.00

2.4 No's 20.00

2.5 No's 4.00

2.6

2.7 18 gauge galvanized sheet steel Sqm 450.00

2.8 Sqm 25.00

2.9 Sqm 25.00

3 MV PANELS

9.43 Cum/Sec or 20,000 CFM @ 25 MM TOTAL STATIC, Motor : 7.5KW, 4pole (FOR FRESH AIR)

11.79 Cum/Sec or 25,000 CFM @ 25 MM TOTAL STATIC, Motor : 7.5KW, 4pole (FOR EXHAUST AIR)

Conducting the CFD ( Computerized Fluid Dynamic analysis and submission of Reports and adjusting the Location of Fans as required

Supply installation testing and Commissioning of Carbon Monoxide Detector as per the specifications

PLC based control panel for CO detectors and control of JET Fans for demand ventilation with a logic Should also enable auto on/off of fans for power saving BASED ON SENSING OF CO LEVEL.

Supply,fabrication,installation & testing of sheet metal smoke extraction cum ventilation ducts with 90 mins Fire rated spray Coating / Paint in accordance with the approved shop drawings complete with all accessories like vanes flanges suspension rods anchor bolts GI bolts and nuts,canvas connections etc,complete.

Supply,installation,testing and balancing of MS Fire Rated (for 90 mins operation) Backdraught dampers with Fire rated BMS compatible actuaters for Exhasut air duct with all Fire rated Cabling accessories etc,complete.

Supply,Installation, Testing & commissioning of Heavy duct Flexible 2mm thick fabric Fire Rated canvas (for 90 mins operation) connection with inspection zip to connect GI Duct












3.1 Blower Room 1 MCCs ( TYPICAL)

No's 4.00

Incoming : 100A 25KA TP MCCB with Neutral link- 1noBus bars : 100A 25KA TPN Aluminium Bus bars – 1Set

Supply, installation, Testing and Commissioning of 3 phase and Neutral 415V 4 wire Free Standing Floor mounted MCC made out of 2mm thick CRCA sheet after seven tank process and painting with Epoxy powder coating.

The panel shall consist of suitable rating TPN Aluminium bus bar (at the rating of 0.8A/Sq.mm) supported with DMC/ SMC barriers and color coded with Heat shrinkable sleeves. The Metering shall be provided as specified.

The panel shall have Short circuit withstanding capacity of minimum 50KA and consist of the switchgear as mentioned below. The panel shall be got fabricated from manufacturers with CPRI Test certificate only.

The MCC shall have at least two spare cubicles of the maximum rating. The size of all Panel Mounting Meters shall be 96X96mm.

The Panels shall be mounted on U channels including supply and fixing of the same. Every ACB shall be provided with ON/OFF /Trip Indication lamps of LED type.

All MCCBs shall be with Electronic releases for Overload, Short Circuit and inbuilt earth fault relay.

Every motor in MCC shall be provided with required Contactors, Overload relay, On/Off Push buttons, On/Off/trip indications in manual mode and Auto/ manual selector switch. The MCC shall be provided with PLC with suitable Inputs/ outputs, power supply, Relays and fully wired in Auto mode including software and other accessories. The PLC shall also be wired to CO sensors for operation as per specifications












Outgoings:

No's 4.00

63A 25KA TP MCCB for 7.5 kw Blower , 4 No's.

Metering :

Suitable rating MPCB with Dual speed Controller suitable for 1.1KW Impulse fan Motor along with PLC for control of impulse fans based on co level - 12Nos .












i) 0 - 500V Digital Voltmeter with Selector switch -1set

No's 4.00

ii) 0 – 100A Digital Ammeter with Resin cast Ctsand selector switch-1setiii) CT operated Electronic Energy Meter with RS 485 connectivity-1setiv) LED type Phase indication lamps withindividual MCB control and toggle switches - 1set

4 MV CABLES

a. 4C X 2.5 Sq.mm Copper. ( from Blower Panel to 7.5 kw Motor) RMT 350.00b. 2Cx1.5sq.mm ( Control Cable for CO Sensors) RMT 700.00c. 6Cx1.5sq.mm ( Power Cable for Jet Fans) RMT 850.005 Cable End Terminations

a. 4C x 2.5 Sq.mm copper No's 24.00b. 2C x 1.5sq.mm No's 40.00c. 6C x 1.5sq.mm No's 80.006 Earthing

a. 25 X 6mm GI Strip RMT 600.00b. 1C x 6 Sq.mm copper wire RMT 600.00

SUB TOTAL FOR BASEMENT VENTILATION

Supply and laying dressing and clamping of 1.1KV grade, PVC insulated Aluminium/Copper conductor armoured Underground cables including all fixing accessories such as clamps for fixing the cable or laid in ground including excavation and refilling of earth and providing protection with sand and bricks as per drawing.

Providing end terminations for following size cables including supply of Double Compression type cable gland, lugs, insulation tape and identification tags complete with end termination and earthing of gland.

Supply and laying of following size strips including including all necessary interconnections with earth station and equipments.












GRAND TOTAL

FIRE FIGHTING WORKS

SYNERGY infra CONSULTANTS PVT.LTD 1

S.NO DESCRIPTION UNIT QTY Supply Instalation1

Rmt 15 6200 300

2

a) )750mm wide x 400mm deep x 600mm Nos 15 3400 200

3

Nos 30 3000 200

4 Nos 15 2000 100

5

Nos 14 6300 300

6 1200

a) 25 mm dia Nos 14 1200 100

7

Nos 15 1200 200

8

a) 150mm dia Rmt 175 1150 450

b) 100mm dia Rmt 75 900 300

c) 80mm dia Rmt 50 750 250

d) 50mm dia Rmt 75 400 150

e) 25mm dia Rmt 50 275 75

9

17500

a) 100mm dia Nos 1 17500 500

Providing and fixing 63 mm dia (2.1/2”) N.B. hydrant Single headed oblique landing Valve in SS Morris Pattern instanteous coupling type ISI certified heavy type hydraulically tested to 250 psi working pressure with necessary nuts, bolts Gaskets, GI chain twist release type plug. including fabricated tee connection, as per IS 5290

Supplying & fixing fire hydrant MS cabinet type shutter enclosure of following size made up of 16 guage MS plate continuously welded on all edges or fabricated with bends at all edges using single plate capable of accommodating the 2 nos. 15 m fire hose And 1 nos.SS branch pipe. Including railway coach lock up arrangement & lever for opening the door after breaking the glass. Each hose box is to be fitted with front glass door painted "FIRE" with red luminous paint. Hinges should be sturdy to bear the weight of fully open door without sagging. Cabinet should be powder coated by standard process on all sides with red paint of approved make suitable for fixing to wall as directed by Architect (flush/surface mounted) etc. complete. Contractor to get sample approved for workmanship from Architect.

Supplying and fixing 63mm dia Hose pipe Reinforced Rubber lined as per IS:636 type-A respectively with 15 M standard length including SS metal male and female Coupling duely bound with GI wire,etc. Complete As directed by Architect in charge.

Supply and fixing of S.S. branch pipe with 63mm dia female inlet and male threaded outlet with hexagonal based nozzle as per IS 903Supplying & fixing first aid fire hosereel of Synthetic rubber suitably reinforced Dunlop/NEWAGE/EQV make 20mm /25 MMsize & 30m standard length with PVC nozzle with cut off valve attachment. Hose to be swinging type wall mounted drum & recessing into hose cabinet to suit location including fixing with lead anchor fasteners & bolts ( Incluiding drum and swivel arrangment ) etc complete.

Providing and fixing ball VALVE heavy quality fullway valves for isolation at inlet to hose reels (ISI certified make) etc. complete.

Supplying and fixing specially designed SS orifice plates on hydrant outlets of landing valves including distant pieces of suitable size for adjustment of delivery pressure of 3.5 kg/ sq.cm as required by LPA complete with necessary companion flanges, nuts, bolts, gaskets etc. complete.

Supplying, installation testing and commissioning of the following (Class 'B') MS pipes and fittings confirming to IS 1239 PI & II, with flanges welded /welded joints) as required including pipe of shorter lengths, tapering connecting pieces, short or long bends, specials like sockets, union nuts, elbows, reducers, plugs, Tees etc.Complete to make the system operative as required by local fire authorities. including welding, cutting, fixing in / on walls, under ground etc., the pipes will have to be laid and fixed in trenches on walls, ceilings, into brick walls or RCC with lead anchor fastners.The work includes excavation in all types of soils and back filling and making holes in brick or RCC walls, slabs/ roofs and making good the damages by bringing to the original condition to the satisfaction of the Architect and painting two coats of approved shade of enamel paint over a coat of approved primer.

Supplying, installation testing and commissioning Cast Iron Body Sluice valve PN 1.6 Non-rising stem type conforming to IS:780, with flanged ends

FIRE FIGHTING WORKS



a) 100mm dia Nos 1 17500 500

11

a) 150mm dia Nos 2 7000 500

12 Nos 2 2300 200

13

a)80mm dia Nos 14 5300 200

14

a) 3C x 1.5.sqmm Rmt 2500 55 10

15 NOS 1 24000 1000

TOTAL RATE

II FIRE HYDRANT INSTALLATION (EXTERNAL)

1

Nos 6 6300 200

2

a) )750mm wide x 250mm deep x 600mm Nos 6 3400 200

3

Nos 12 3000 200

4 Nos 6 2000 100

Supplying, installation testing and commissioning C.I. Non-return valve conforming to IS : 5312 with flanged ends (heavy) tested to 250 psi hydraulic pressure with necessary companion flanges, bolts, nuts, gasket packing and any other spares, including indicator for open ands hut position as per fire practice etc complete.

Supply and installation of CI Butterfly valves (heavy) tested to 250 psi hydraulic pressure with Vertical/horizontal gear unit with appropriate handle conforming to IS:13039 with necessary companion flanges, neoprene gaskets with necessary companion flanges, bolts, nuts, gasket packing and any other spares, including indicator for open and Shut position as per fire practice etc complete.

Supply, installation, testing & commissioning of Gun metal Air release valve with ball valve - 25mm dia

Supply installation and fixing of flow switches in the following Pipe line with 1NO+1NC Contacts

Supply and installation, and fixing of 1.1KV PVC XLPE insulated cables of copper conductor with double compression type cable gland and heavy duty tinned copper cable sockets as per the relevant IS standards. Rate shall be inclusive of all sundry materials like adhesive tape , PVC sleeves , bolts and nuts, washers etc. including plugging unused holes.

Supply, installation, testing & commissioning of 16 WINDOW ANNUNCIATION PANEL FOR FIRE INDICATION from flow switch

Providing and fixing 63 mm dia (2.1/2”) N.B. hydrant single headed oblique landing Valve in SS Morris Pattern instanteous coupling type ISI certified heavy type hydraulically tested to 250 psi working pressure with necessary nuts, bolts Gaskets, GI chain twist release type plug. including fabricated tee connection, as per IS 908

Supplying & fixing fire hydrant MS cabinet type shutter enclosure of following size made up of 16 guage MS plate continuously welded on all edges or fabricated with bends at all edges using single plate capable of accomodating the 2 nos. 15 m fire hose And 1 nos SS branch pipe. Including railway coach lock up arrangement & lever for opening the door after breaking the glass. Each hose box is to be fitted with front glass door painted "FIRE" with red luminous paint. Hinges should be sturdy to bear the weight of fully open door without sagging. Cabinet should be powder coated by standard process on all sides with red paint of approved make suitable for fixing to wall as directed by Architect (flush/surface mounted) etc. complete. Contractor to get sample approved for workmanship from Architect.

Supplying and fixing 63mm dia Hose pipe Reinforced Rubber lined as per IS:636 Part-A respectively with 15 M standard length including SS metal male and female Coupling duely bound with GI wire,etc. Complete As directed by Architect in charge.

Supply and fixing of S.S. branch pipe with 63mm dia female inlet and male threaded outlet with hexagonal based nozzle as per IS 903

FIRE FIGHTING WORKS



Nos 6 1200 200

6

a) 150mm dia Rmt 150 1150 450

b) 100mm dia Rmt 35 900 300

c) 80mm dia Rmt 15 750 250

7

Nos 1 21500 500

8

Nos 1 27500 500

9

Nos 3 12500 1500

10

a) 150mm dia Nos 3 21500 500

11

Supplying and fixing specially designed SS orifice plates on hydrant outlets of landing valves including distant pieces of suitable size for adjustment of delivery pressure of 3.5 kg/ sq.cm as required by LPA complete with necessary companion flanges, nuts, bolts, gaskets etc. complete.

Supplying, installation testing and commissioning of the following (Class 'B') MS pipes and fittings confirming to IS 1239 PI & II, with flanges welded /welded joints) as required including pipe of shorter lengths, tapering connecting pieces, short or long bends, specials like sockets, union nuts, elbows, reducers, plugs, Tees etc.Complete to make the system operative as required by local fire authorities. including welding, cutting, fixing in / on walls, under ground etc., Underground piping with necessary flanges & fittings such as elbows,tees and providing and fixing anchor blocks in PCC 1:2:4 at all bends, tees, alongwith pipe coating and wrapping of underground pipes with `PYPKOTE' 4mm thick conforming to IS : 10221. It includes providing and fixing pypkote (corrosion protection tape) including supply and application of pipe coating and spiral Wrapping (wrapping should have overlap of 15 to 20 mm) etc. complete as per ASTM standards for corrosion protection of pipes that will be laid under the ground]

Supplying, installing and commissioning of fire brigade inlet connection conforming to IS 5290 comprising of 2nos.SS 63mm dia instantaneous couplings complete with CI non-return valve, CI butterfly valve, connected to 150 mm dia Fire TANK FILLINGand fire hydrant wet riser pipe.

Supplying, installing and commissioning of fire brigade inlet connection conforming to IS 5290 comprising of 4nos.SS 63mm dia instantaneous couplings complete with CI non-return valve, CI butterfly valve, connected to 150 mm dia forRING MAIN

Constructing masonry Chamber 1200x1200x1000 mm, inside with 75 class designation brick work in cement mortar 1:6 ( 1 cement : 6 fine sand ) for sluice valve, with C.I.surface box 100mm top diameter, 160mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand ) 12mm thick finished with a floating coat of neat cement complete as per standard design including curing, back filling of the chamber sides with the excavated soil, disposing of the surplus earth after back filling with initial lead of 30 meters. Providing medium duty cast iron frame and cover etc., complete. ( weight: 110kgs.) as per specification.

Supply, installation, testing & commissioning of Cast Iron Body Sluice valve PN 1.6 Non-rising stem type conforming to IS:14846, with flanged ends

Supply, installation, testing & commissioning of R.C.C NP2 class Hume pipe laid to the required level and grade with collars jointed with in CM1:3. Including encasing the pipe around a depth of not less than 15cm thick with selected earth (fine aggregate) available from the excavation as per specification and direction of the engineer. The excavated soil shall be deposited on banks with all lead, lift, including necessary wooden/steel form work where ever required. Depositing of the surplus earth after backfilling to a initial lead of 30 meters. Refilling of the pipe line trenches and foundation with selected earth available from the trench excavation including watering consolidation in layers of 15cm thickness complete as per specifications. The back fill soil shall be graded soil free from stones, pebbles, clay lumps and vegetation etc., complete as per the specifications, and drawings.

FIRE FIGHTING WORKS


S.NO DESCRIPTION UNIT QTY Supply Instalationa) 300mm dia Rmt 20 1200 200

12 Nos 3 2300 200

13

a) 150mm dia Nos 3 7000 500

TOTAL RATE

III FIRE PUMP HOUSE

1

Nos 2 15000

2

Nos 1 455000 20000

3

Nos 1 95000 5000

4

RO 1 45000 5000

Supply, installation, testing & commissioning of Gun metal Air release valve with ball valve - 25mm dia

Supply and installation of CI Butterfly valves (heavy) tested to 250 psi hydraulic pressure with Vertical/horizontal gear unit with appropriate handle conforming to IS:13039 with necessary companion flanges, neoprene gaskets with necessary companion flanges, bolts, nuts, gasket packing and any other spares, including indicator for open and Shut position as per fire practice etc complete.

Supplying & installing completely testing & commissioning of electrically Driven End suction and back pull out pump with cast iron casing & bronze or phosphor bronze internal parts, for fire duty, complete with coupling guard necessary RCC foundation,capable of discharging 2850 lt/min against 88 metre head at 8.8 bar against all losses complete electrically operated TEFC 3-ph, 440-V, 50 Hz, 2900 RPM motor of ‘F’ class winding, make as approved by TAC with automatic direct on line starter complete with single phasing preventor & No volt release as per LPA requirements common base plate, foundation bolts, suitable cable entry gland box for A-AL cable (95 sq.mm) pressure guages & wired for automatic start of the water pump on drop of pressure in the wet riser/ hydrant and sprinkler system. The motor starter and pump should confirm to LPA / BSES & and IE Regulations. The pump shall be capable of giving not less than 150% discharge at a head not less than 65% of the rated head.(Main Hydrant Pump and sprinkler)

Supplying & installation, testing & commissioning of End suction and back pull out diesel engine driven pump of capacity 2850 Litr/Min, 88 Mtrs head Common Standby pumpset for wetriser & sprinkler system at 8.8 Bar and 2900 rpm with all necessary accessories like bronze impeller, stainless steel shaft and mechanical seal along with anti-vibration mounting, coupling, gear box, base plate for pump, fabricated mild steel channel with foundation bolts etc., It includes providing and fixing fuel oil tank (capacity as perTAC requirements) with supports and necessary pipe works for diesel engine, battery and battery charger to be connected to control panel of diesel engine and exhaust silencer including necessary pipe work insulation and cladding, etc., and shall be automatic in operation with diesel engine control diesel engine control panel with 24V DC storage battery & its battery charger. (diesel engine)

Supplying, installing, testing and commissioning of electrical motor Driven jockey pump for hydrant system with discharge 180 lpm against head 88 mtrs at 8.8 bar with M.S. frame and clamps as necessary for fixing the pumps on the foundation slab as per site conditions

Supplying, installing, testing and commissioning of electrical motor Driven Booster pump for hydrant system with discharge 900 lpm against head 35 m with M.S. frame and clamps as necessary for fixing the pumps on tthe foundation of slab as per site conditions

FIRE FIGHTING WORKS



Incoming – 400A,50KA FP MCCB -1set(with Mechanical interlocking between incommers and Bus couplers)Busbars : 400A TPN aluminium BUSBARS- 1SET

(2) DOL starter same as above for 15HP motor - 1set

(3) 63A , TPN MCCB for terrace booster pump - 1 Set

(4) 32A, TPN MCB feeder for Engine control panel-1 Set

Nos 1 220000 5000

6

RO 1 13000 2000

7

Supply, Installation, Testing and Commissioning of Indoor / outdoor, weatherproof 3 phase 415V 4 wire Free Standing Floor mounted MV panel made out of 14 SWG CRCA sheet after seven tank process and painting with Epoxy powder coating including all switchgear as detailed below. The panel shall consist of suitable rating TPN Aluminium/Copper busbar (at the rating of 0.8A/Sq.mm/1.6A/sq.mm) supported with DMC/ SMC barriers and colour coded with Heat shrinkable sleeves.The Metering shall be provided as specified. The panel shall have Short circuit with standing capacity of minimum 50KA and consist of the switchgear as mentioned below. The panel shall be mounted on channels grouted to the existing floor including all materials. The panel shall be got fabricated from manufacturers with CPRI Test certificate only. All the PCC/ Panels shall have at least two spare cubicles of the maximum rating. All feeders shall be earthed with 2 GI flats of adequate size to the main earth bus of 50x6mm GI flat. The size of all Panel Mounting Meters shall be 96X96mm.The Panels shall be mounted on U channels including supply and fixing of the same.All MCCBs shall have 80-100% thermal setting plug. MCBs shall be provided for Control purposes.

Supply, installation, testing and commissioning of electrical control panel diesel engine main motor and jockey pump, comprising of following. All contactors shall have status feed back provision to BMS.

Outgoings : (1) DOL starter with MCCB and contactor, over load relay,single phasing preventor and ON/OFF/TRIPindication lamps for motor -2sets

Metering ; Voltmeter, Ammeter, LED phase Indication lamps, Ammeters for both outgoings The Rate shall include supply and fixing of all The Rate shall include supply and fixing control devices for auto operation of pump of all motors

Supply, installation, testing and commissioning of weather proof type starter consisting of following and made of 2mm thick CRCA sheet including painting with epoxy powder coating for 15HP Booster pump motor. The box shall be suitable for terminating AYFY cable of 3core 6sq.mm size. The box shall be mounted on suitable angle frame work of 450mm height on a PCC pedestal including all materials. The stater shall have status feed back provision to BMS

DOL starter suitable for 15HP with MPCB and contactor, over load relay, single phasing preventor and ON/OFF/TRIP indication A/M selection switch & push button for manual operations and with volt meter,Ammeter with selector switches

Supplying, installation testing and commissioning of the following (Class 'B') MS pipes and fittings confirming to IS 1239 PI & II. The pipes complete with necessary specials such as tees, bends, flanges, reducers, etc. Rate quoted shall include for painting of pipe with a coat of primer and two coats of synthetic enamel paint of approved colour / make for aboveground piping and coating & wrapping for under ground piping as per the TAC / IS standards and Local fire service department requirement complete including supply and installation of pipe supports, fasteners etc.,

Above ground piping with necessary flanges & fittings such as elbows, tees and Painting, supports and Orifice plates if any necessary for the fire protection system complete as per the requirement of Local fire service department.

FIRE FIGHTING WORKS


S.NO DESCRIPTION UNIT QTY Supply Instalationa) 200mm dia Rmt 30 1400 600

b) 150mm dia Rmt 20 1150 450

c) 100 mm dia Rmt 15 900 300

d) 80 mm dia Rmt 15 750 250

e) 50 mm dia Rmt 25 400 150

f) 25 mm dia Rmt 30 275 75

8

a) 200mm dia Nos 4 27500 500

b) 150 mm dia Nos 4 21500 500

c) 100mm dia Nos 1 17500 500

d) 80mm dia Nos 1 14500 500

9

a) 200mm dia Nos 1 27500 500

b) 150mm dia Nos 3 21500 500

c) 80mm dia Nos 1 17500 500

10

a) 200mm dia Nos 3 31500 500

b) 100mm dia Nos 1 17500 500

11

a) 25 mm dia Nos 5 2400 100

12

a) 25mm dia Nos 5 2400 100

13

Nos 1 12500 1500

14Nos 10 2200 100

15 Nos 5 4500 200

16 Supply fabrication and erection of MS angle supports for Pipe lines Ton 1 60000 5000

17

a) 3C x 120.sqmm AYFY cable ( to main pump ) Rmt 60

b) 4C x .16sqmm AYFY cable ( for jockey pump & booster pumps) Rmt 25

c) 3C x 1.5.sqmm copper control cable ( To Pressure switches controllers) Rmt 75

Supplying, installation testing and commissioning Cast Iron Body Sluice valve PN 1.6 Non-rising stem type conforming to IS:780, with flanged ends

Supplying, installation testing and commissioning C.I. Non-return valve conforming to IS : 5312 with flanged ends (heavy) tested to 250 psi hydraulic pressure with necessary companion flanges, bolts, nuts, gasket packing and any other spares, including indicator for open ands hut position as per fire practice etc complete.

Supplying, installation testing and commissioning Foot valve/strainer with Flanged ends.

Supplying, installation testing and commissioning of G.M. gate valves conforming to IS 778

Supplying, installation testing and commissioning of G.M. Non-return valves conforming to IS 778

Supplying and fixing MS fabricated air vessel at pump room about 250mm dia and 1500mm high on MS stand with necessary cut off drain and air release arrangements and leading the drain pipe to the sump at pump room with painting with red oxide primer and finished with fire red enamel paint. It shall be inclusive of all relevant pipes, valves, specials upto pump header and other accessories as per Local fire service department standard / requirement. including TAC approved pressure gauge with cork and of suitable range as for Providing required pressure etc. complete.

Supplying, installation testing and commissioning of Pressure gauge (0-14 Kg./sqcm) of 100 mm dia Dial size with required fittings and accessories

Supplying, installation testing and commissioning of Pressure switch (0-15 Kg./sqcm) with required fittings and accessories

Supplying, installation testing and commissioning of End termination for 1.1KV cables with double compression type cable gland and heavy duty tinned copper cable sockets as per the relevant IS standards. Rate shall be inclusive of all sundry materials like adhesive tape , PVC sleeves , bolts and nuts, washers etc. including plugging unused holes.

FIRE FIGHTING WORKS



a) 150mm dia Set 1

19

a)300mmX50mm Rmt 60

20

a)50X6mm GI strip Rmt 30b)25X3mm GI strip Rmt 30c) 8SWG GI Wire Rmt 10

21

Nos 1

TOTAL

IV AUTOMATIC SPRINKLER SYSTEM.

1

Nos 700

2

Nos 100

3 Nos 250

4

a) 100mm dia Nos 10

b) 80mm dia Nos 4

c) 50mm dia Nos 4

5

a) 150 mm dia

Supply, fixing, testing and commissioning & installation of alarm gong valve assemble contains of 1-no. Alarm valve, 1 no. Main stop valve, 1 no. water meter with alarm gong, Pressure guage drain valve and drain piping etc.,

Supply and installation of GI Perforated cable trays of following sizes made out of 2mm thick GI sheet including all supports as required

Supply and laying of following size hot dip galvanized GI strips to run along with cable trays for erathing of all motors

Supplying, installation testing and commissioning priming HDPE tank (Sintex) of 500Ltrs capacity at required level including MS angle supports, with inlet,outlet,overflow & drain pipes including controlling valves,welding of supports bolts and nuts etc., complete accessories

Supply and installation, Providing and fixing approved make 15mm orifice quartzoid bulb type sprinklers, 68°C rating, recessed pendent type with roset plate (adjustable) off white finish wherever required and all accessories, supports and painting etc.

Supply and installation, Providing and fixing approved make 15mm orifice quartzoid bulb type sprinklers, 68°C rating, recessed wall mounted type with roset plate (SINGLE ) off white finish wherever required and all accessories, supports and painting etc.

Supply and installation, testing and commissioning of Sprinkler flexible Pipe required length of 1.5M including angles and supports Supply and installation of CI Butterfly valves (heavy) tested to 250 psi hydraulic pressure with Vertical/horizontal gear unit with appropriate handle conforming to IS:13039 with necessary companion flanges, neoprene gaskets with necessary companion flanges, bolts, nuts, gasket packing and any other spares, including indicator for open ands hut position as per fire practice etc complete.

Supplying, installation testing and commissioning of the following (Class 'B') MS pipes and fittings confirming to IS 1239 PI & II, The pipes complete with necessary specials such as tees, bends, flanges, reducers, etc. Rate quoted shall include for painting of pipe with a coat of primer and two coats of synthetic enamel paint of approved colour / make for aboveground piping and coating & wrapping for under ground piping as per the TAC / IS standards and Local fire service department requirement complete including supply and installation of pipe supports from column/wall or suspenders from roof slab to suit various dia of pipes made out of GI adjustable rods threaded for a sufficient length to adjust the height of support along with clamping arrangement for holding pipes of anchor fastening arrangement design of hanger and should confirm to specification as indicated NFPA 13. etc.,


FIRE FIGHTING WORKS


S.NO DESCRIPTION UNIT QTY Supply InstalationSupply Rmt

installation Rmt

b) 100mm diaSupply Rmt

installation Rmt

c) 80mm diaSupply Rmt

installation Rmt

d) 65mm diaSupply Rmt

installation Rmt

e) 50 mm diaSupply Rmt

installation Rmt

f) 40 mm dia.Supply Rmt

installation Rmt

g) 32 mm diaSupply Rmt

installation Rmt

h) 25 mm diaSupply Rmt

installation Rmt

6

a)50 mm dia Rmt 60

b)40 mm dia Rmt 30

c)25 mm dia Rmt 120

7

a)100mm dia Nos 10b)80mm dia Nos 4

8

a) 50 mm dia No 14

a) 25 mm dia No 4

9

a) 3C x 1.5.sqmm Rmt 2500

10 NOS 1

TOTALV WATER CURTAIN SYSTEM.

Supplying, installation testing and commissioning of the CPVC pipes as per IS:16088Above ground piping with necessary flanges & fittings such as elbows, tees and supports and Orifice plates if any necessary for the fire protection system complete as per the requirement of Local fire service department.

Supply installation and fixing of flow switches in the following Pipe line with 1NO+1NC Contacts

Supplying, fixing and testing approved make gun metal ball valve conforming to IS 778 with unions etc., complete as per specifications.

Supply and installation, and fixing of 1.1KV PVC XLPE insulated cables of copper conductor with double compression type cable gland and heavy duty tinned copper cable sockets as per the relevant IS standards. Rate shall be inclusive of all sundry materials like adhesive tape , PVC sleeves , bolts and nuts, washers etc. including plugging unused holes.

Supply, installation, testing & commissioning of 16 WINDOW ANNUNCIATION PANEL FOR FIRE INDICATION from flow switch

FIRE FIGHTING WORKS



a) 80mm dia Rmt 300

2

a) 80mm dia Nos 5

3

Nos 5

4 Nos 120

5

Rmt 1500

TOTAL

Supplying, installation testing and commissioning of the following (Class 'C') GI pipes and fittings confirming to IS 1239 PI & II, for water curtain system . The pipes complete with necessary specials such as tees, bends, flanges, reducers, etc. Rate quoted shall include for painting of pipe with a coat of primer and two coats of synthetic enamel paint of approved colour / make for aboveground piping and coating & wrapping for under ground piping as per the TAC / IS standards and Local fire service department requirement complete including supply and installation of pipe supports from column/wall or suspenders from roof slab to suit various dia of pipes made out of GI adjustable rods threaded for a sufficient length to adjust the height of support along with clamping arrangement for holding pipes of anchor fastening arrangement design of hanger and should confirm to specification as indicated NFPA 13. etc.,


Supply,installation,testing and commissioning of Motorized Butterfly valve with actuator for Water curtains with electrical motors suitable for 220V, Single Phase 50Hz AC supply operation

Supply and installation, of control panel for water curtain motor consisting of suitable relay MPCB ,DOL starter with contactor , over load relay, auto/manual switch ,push buttons in manual mode and ON/OFF trip indicators all prewired

Supply,installation,testing and commissioning of 15mm Dia open type water curtain nozzles with k-factor of 25-32.Supplying, installation testing and commissioning of End termination for 1.1KV cables with double compression type cable gland and heavy duty tinned copper cable sockets as per the relevant IS standards. Rate shall be inclusive of all sundry materials like adhesive tape , PVC sleeves , bolts and nuts, washers etc. including plugging unused holes.

c) 3C x 2.5.sqmm copper control cable ( To motorized butterfly valve to panel)

FIRE FIGHTING WORKS


S.NO DESCRIPTION UNIT QTY Supply Instalation

VI ADDRESSABLE FIRE ALARM SYSTEM

1

1.1 6 Loop fire alarm panel (with each loop supporting 125 Detectors & Devices). No 1

2 Mtr 4500

3 No 325

4 No 325

5 No 325

6 No 18

7 No 18

9 Supply and fixing of Exit Light fixtures with 1.5hrs battery backup No 22

10 No 30

11 No 20

12 Supply and fixing of duct detectors for AHU's at different levels. No 20

13 No 1

14

c) Establishing two way communication with master panel and slave panels. No 1

15 RO 1

TOTAL

VII PUBLIC ADDRESS SYSTEMS.NO DESCRIPTION

Supply, fixing, testing and commissioning of the following number of Loops Microprocessor based analogue addressable type Fire Control panel with Zonal Indications , The system should have BMS compatibility, The system shall have a built-in relay & Hooter to initiate failure of FACP.

Supply testing and laying of PVC insulated, 1.5sq.mm shielded armoured twisted pair copper cable including all fixing accessories when laid inside the building including complete with end terminations at both sides.

Supply installation testing and commissioning of analogue addressable type Multi (smoke& Heat ) photo electric detectors with LED indication lamp and with in built fault isolator.(Below false ceiling) with complete fixing accessories.

Supply installation testing and commissioning of analogue addressable type Multi (smoke& Heat ) photo electric detectors with LED indication lamp and with in built fault isolator.(Above false ceiling) with complete fixing accessories.

Supply installation testing and commissioning of response indicators with all fixing accessories Supply installation testing and commissioning of Loop sounders with all fixing materials. Supply and installation of analogue addressable type Manual call points with Glass, hammer and monitor module and fixing accessories

Supply installation testing and commissioning of analogue addressable type monitor modules for monitoring the sprinkler flow switches

Supply installation testing and commissioning of analogue addressable type control relay / control modules for AHUS, Electrical circuit tripping, and PA amplifier activation in case of fire alarm.

Supply, installation, testing and commissioning of intelligent Addressable network control Active Repeater panel on FACP network configuration to monitor and control all local fire alarm control panels with RS 485 port on CPU board with optional network software connectivity, fire/ fault indicators, audio visual signals, battery, battery charger, central processing unit 80 character display unit complete in all respects.

Supply, installation, testing and commissioning of Fire alarm management software system and graphical display interface to network the installed fire alarm panels using a network manager program and the following shall be pre-equipped with :

a) Preparation of graphics compatible to fire alarm monitoring software of buildings and connected with slave panels including layout of the building and wiring diagram of the fire alarm system

b) Interconnecting the same with fire alarm software located at master panel testing the parameters and operations of individual detectors and slave panels

A server based PC with 21” LCD monitor with 4 GB RAM loaded, 500GB HDD , with per-loaded software's shall include UPS with 15 min backup and along with all fixing accessories. ( The above said item shall be in client scope )

FIRE FIGHTING WORKS



Nos 45

3 Mtr 3000

4 Mtr 3500

5 Nos 1

6 Nos 1

TOTALVIII FIRE EXTINGUISHERS1

Nos 78

2

Nos 78

3

Nos 10

4 Nos 18

5

Sq.ft 50 0

21943TOTAL Rs.

Supply and installation testing and commissioning of 6Watt 180mm dia recessed/ surface mounted white color speakers (along with junction boxes to be used in no false ceiling area).

Supply and surface laying of 25mm dia heavy guage PVC conduits including all fixing accessories like saddles etc ( Shall be on actuals ).Supply and laying of shielded twin twisted pair 1.0 sqmm cable in existing conduit ( Shall be on actuals ).Supply installation testing and commissioning of 480 watts amplifiers complete with accessoriesSupply installation and testing of GOOSE NECK MICROPHONE for announcement purpose.

Supply installation testing and commissioning of Water CO2 type Fire Extinguisher of 9lit capacity, fitted with discharge control valve ( squeeze grip type ) , inside STORED PRESSURE with ISI mark, with discharge hase and open nozzel overall conforming to IS: 15683 with ISI mark along with wall bracket and initial refilling at site . Fire Rating 2A.

Supply installation testing and commissioning of CO2 type Fire Extinguisher of 4.5 kgs capacity made from brand new seamless drawn steel cylinder as per IS : 7285 with ISI mark and Chief of controller of explosives approval, fitted with wheel valve as per IS: 3224 with ISI mark, with discharge hose and horn and supplied complete with initial charge overall conforming to IS: 15683 with ISI mark and wall bracket. Fire Rating 21B

Supply installation testing and commissioning of ABC Dry Chemical Powder 6.0 kg capacity fitted with discharge control valve ( squeeze grip type ), inside STORED PRESSURE with ISI mark and ABC powder as per IS: 14609 ( for ABC class ) with ISI mark packed in 6kgs HDPE bags, with discharge hose and open nozzel and supplied complete with initial charge overall conforming to ISI: 15683 ISI mark and wall bracket . Fire Rating 3A.34B.

Supply installation testing and commissioning of Clean Agent Fire Extinguishers, 2.0 kg capacitySealing of Fire shafts at all floor levels by using M.S. angle Iron frame around the shaft M.S. chequered plate and PCC of 1:2:4 (100mm thick) on the plate for whole shaft area as per drawings and engineer- in - charge.

FIRE FIGHTING WORKS


AMOUNT

FIRE FIGHTING WORKS


AMOUNT

AMOUNT

FIRE FIGHTING WORKS


AMOUNT

hvac boq r1- 29-08-2013 (2)

Documents