hướng dẫn cài đặt sip trunking với tổng đài siemens hipath 3000
DESCRIPTION
Tổng đài nội bộ hiện hữu thì đòi hỏi việc chọn lựa những giải pháp tương ứng cho việc tối ưu hoá chi phí đầu tư và hiệu quả sử dụng. Công nghệ VoIP phát triển từng ngày từng giờ, do đó bài toán đặt ra là chi phí đầu tư phải mang lại hiệu quả lợi ích công việc, đi đôi với khấu hao thiết bị phù hợp với xu thế phát triển công nghệ. Chúng tôi cũng đưa ra một giải pháp tham khảo về việc Xây dựng một hệ thống tổng đài IP-PBX dựa trên việc tận dụng các tiện ích dịch vụ sẳn có của các Nhà cung cấp Dịch vụ SIP, phần nào tiết kiệm chi phí đầu tư, cũng như hiểu thêm một số mô hình hệ thống VoIP có thể áp dụng phù hợp cho hiện trạng của hệ thống.TRANSCRIPT
![Page 1: Hướng dẫn cài đặt SIP Trunking với tổng đài Siemens Hipath 3000](https://reader035.vdocuments.site/reader035/viewer/2022081800/5475563fb4af9f9d0a8b5a5a/html5/thumbnails/1.jpg)
Setting up a SIP provider on a Siemens HiPath 3000 PBX
Pre requirements:
- HiPath 3000 V6.0 / V7.0 / V8.0 PBX
- HXG 1500 card
- Broadband Internet Access
- A sip provider account (sipgate, qsc...)
- HiPath 3000 Manager E
- About 10 minutes time to set it up
First logon to the HXG 1500 and authenticate.
![Page 2: Hướng dẫn cài đặt SIP Trunking với tổng đài Siemens Hipath 3000](https://reader035.vdocuments.site/reader035/viewer/2022081800/5475563fb4af9f9d0a8b5a5a/html5/thumbnails/2.jpg)
Now select the Explorers tab, hit Voice Gateway and Internet Telephony Service Provider.
Rightclick your Provider and hit Edit Internet Telephony Service Provider.
![Page 3: Hướng dẫn cài đặt SIP Trunking với tổng đài Siemens Hipath 3000](https://reader035.vdocuments.site/reader035/viewer/2022081800/5475563fb4af9f9d0a8b5a5a/html5/thumbnails/3.jpg)
Tick the Enable Provider check box and select the Provider Identifier (Provider 1) and verify that all those settings are
correct.
![Page 4: Hướng dẫn cài đặt SIP Trunking với tổng đài Siemens Hipath 3000](https://reader035.vdocuments.site/reader035/viewer/2022081800/5475563fb4af9f9d0a8b5a5a/html5/thumbnails/4.jpg)
Now you have to setup your SIP logon, right click your created provider and hit Add Internet Telephony Station.
Enter your account details and press Apply.
![Page 5: Hướng dẫn cài đặt SIP Trunking với tổng đài Siemens Hipath 3000](https://reader035.vdocuments.site/reader035/viewer/2022081800/5475563fb4af9f9d0a8b5a5a/html5/thumbnails/5.jpg)
Next you have to add an MSN which is the number that is sent out to your provider as caller number and used for
inbound calls.
Right click MSN and hit Add MSN. Insert your number the destination that will ring when this number is dialled and
press Apply.
![Page 6: Hướng dẫn cài đặt SIP Trunking với tổng đài Siemens Hipath 3000](https://reader035.vdocuments.site/reader035/viewer/2022081800/5475563fb4af9f9d0a8b5a5a/html5/thumbnails/6.jpg)
Next right click Sip Parameters and select Edit Sip Parameters and change the maximum possible provider calls to a
valid number (calculate about 80kbit/s for one SIP call).
This is the HXG part finished press the Save button on the bottom of the window and close the explorer.
![Page 7: Hướng dẫn cài đặt SIP Trunking với tổng đài Siemens Hipath 3000](https://reader035.vdocuments.site/reader035/viewer/2022081800/5475563fb4af9f9d0a8b5a5a/html5/thumbnails/7.jpg)
On the Manager E, select Lines/Networking and hit IP Trunks. In there create the same amount of B-Channels that
you have selected on the HXG card and select the same provider as in the network card and hit Add.
Under Routes rename the Trk Group 12 to your provider name.
![Page 8: Hướng dẫn cài đặt SIP Trunking với tổng đài Siemens Hipath 3000](https://reader035.vdocuments.site/reader035/viewer/2022081800/5475563fb4af9f9d0a8b5a5a/html5/thumbnails/8.jpg)
Select the Routing Parameters tab and change the settings according to the picture.
Browse to least cost routing and activate it and set it to en-bloc sending.
![Page 9: Hướng dẫn cài đặt SIP Trunking với tổng đài Siemens Hipath 3000](https://reader035.vdocuments.site/reader035/viewer/2022081800/5475563fb4af9f9d0a8b5a5a/html5/thumbnails/9.jpg)
Enter into the dial plan the sipgate testnumber as an extension -1XXXX and chose an available routing table (in my
case 4) and create another rule for example for mobile calls starting with 01 to use that trunk enter 0C01Z and select
a different routing table.
In the configured routing tables setup the route Sipgate (Your provider name) and create a Dial rule with the
following settings for the internal destination starting with the dash (-)
![Page 10: Hướng dẫn cài đặt SIP Trunking với tổng đài Siemens Hipath 3000](https://reader035.vdocuments.site/reader035/viewer/2022081800/5475563fb4af9f9d0a8b5a5a/html5/thumbnails/10.jpg)
For the mobile calls (external numbers) simply set the Dial rule format to A because it should send out every
information you dial
That’s it happy testing and phoning ;)