STANDARDCutting tubes and solids on manualand (semi-)automatic sawing machines

HSS SERIES

Suggested cutting speed: 80 - 140 m/min.Feed: 0,04 - 0,09 mm/tooth.

For more information:

www.kinkelder.com

Cutting tubes and solids on manual sawing machines

The steam treated Alpha saw blade has a blue Oxide surface layer for a longer blade life compared to the uncoated saw blade. It is mainly being used for cutting steel on manual and semi-automatic sawing machines.

Due to the higher oxidation temperature, this TiN coated Solar saw blade is able to cut applications with high tensile strengths.

APPLICATIONS

APPLICATIONS

PARAMETERS

PARAMETERS

MACHINES

MACHINES

All applications like tubes, profiles and solids. All structural steels and non-alloy tool steel with a tensile strength up to 700 N / mm2

All applications like tubes, profiles and solids with a tensile strength up to 750 N / mm2

Suggested cutting speed: 30 - 60 m/min.

Manual, semi-automatic

Manual, semi-automatic, automatic

160175200225250275300315325350370400425450

1,2 / 1,6 / 2,01,6 / 2,01,2 / 1,6 / 1,8 / 2,01,2 / 1,6 / 2,0 / 2,51,2 / 1,6 / 2,0 / 2,51,2 / 1,6 / 2,0 / 2,5 / 3,01,6 / 2,0 / 2,5 / 3,02,0 / 2,5 / 3,02,0 / 2,5 / 3,02,0 / 2,5 / 3,0 / 3,52,0 / 2,5 / 3,0 / 3,52,5 / 3,0 / 3,5 / 4,0 / 4,52,5 / 3,0 / 3,5 / 4,02,5 / 3,0 / 3,5 / 4,0

32323232 / 4032 / 4032 / 4032 / 38 / 4032 / 4032 / 4032 / 40 / 5040 / 5040 / 5032 / 40 / 5040 / 50

TeethDiameter(mm)

Kerf(mm)

Bore hole(mm)

80 / 100 / 120 / 16064 / 90 / 110 / 140 / 18072 / 100 / 128 / 160 / 20064 / 80 / 90 / 120 / 150 / 180 / 22064 / 80 / 100 / 110 / 128 / 160 / 200 / 24072 / 78 / 84 / 96 / 110 / 120 / 144 / 180 / 220 / 28080 / 90 / 100 / 110 / 120 / 140 / 160 / 200 / 240 / 32072 / 80 / 90 / 100 / 110 / 120 / 140 / 160 / 200 / 250 / 32090 / 100 / 110 / 130 / 150 / 170 / 200 / 250 / 32080 / 90 / 110 / 120 / 140 / 160 / 180 / 220 / 280 / 35070 / 80 / 90 / 100 / 110 / 120 / 140 / 160 / 190 / 220 / 30070 / 80 / 90 / 100 / 128 / 140 / 160 / 180 / 200 / 250 / 32070 / 80 / 100 / 110 / 120 / 130 / 140 / 160 / 180 / 220 / 260 / 35080 / 90 / 100 / 120 / 140 / 180 / 240 / 280

TYPICAL AVAILABE HSS ALPHA SAW BLADES

Due to a sophisticated PVD coating for wear protection which achieves a very low friction coefficient, the Eclipse saw blade is a cost efficient solution for cutting structural and non-alloy tool steel thin walled tubes.

When cutting tubes and profiles on manual and semi-automatic sawing machines, Eclipse allows a higher cutting speed than a steam treated saw blade. It can even be used for cutting thin walled tubes on automatic machines. Eclipse is also very suitable for cutting stainless steel tubes and profiles.

Advantages compared with steam treated• Higher blade life • Higher production output• Increased uptime • Ideal for cutting both structural steel• Lower cost per cut and stainless• Little or no side pick-up

60 - 120 m/min 30 - 50 m/min220 - 260 m/min 60 - 120 m/min

160175200225250275300315325350370400425450

1,2 / 1,6 / 2,01,6 / 2,01,2 / 1,6 / 1,8 / 2,01,2 / 1,6 / 2,0 / 2,51,2 / 1,6 / 2,0 / 2,51,2 / 1,6 / 2,0 / 2,5 / 3,01,6 / 2,0 / 2,5 / 3,02,0 / 2,5 / 3,02,0 / 2,5 / 3,02,0 / 2,5 / 3,0 / 3,52,0 / 2,5 / 3,0 / 3,52,5 / 3,0 / 3,5 / 4,0 / 4,52,5 / 3,0 / 3,5 / 4,02,5 / 3,0 / 3,5 / 4,0

32323232 / 4032 / 4032 / 4032 / 38 / 4032 / 4032 / 4032 / 40 / 5040 / 5040 / 5032 / 40 / 5040 / 50

TeethDiameter(mm)

Kerf(mm)

Bore hole(mm)

80 / 100 / 120 / 16064 / 90 / 110 / 140 / 18072 / 100 / 128 / 160 / 20064 / 80 / 90 / 120 / 150 / 180 / 22064 / 80 / 100 / 110 / 128 / 160 / 200 / 24072 / 78 / 84 / 96 / 110 / 120 / 144 / 180 / 220 / 28080 / 90 / 100 / 110 / 120 / 140 / 160 / 200 / 240 / 32072 / 80 / 90 / 100 / 110 / 120 / 140 / 160 / 200 / 250 / 32090 / 100 / 110 / 130 / 150 / 170 / 200 / 250 / 32080 / 90 / 110 / 120 / 140 / 160 / 180 / 220 / 280 / 35070 / 80 / 90 / 100 / 110 / 120 / 140 / 160 / 190 / 220 / 30070 / 80 / 90 / 100 / 128 / 140 / 160 / 180 / 200 / 250 / 32070 / 80 / 100 / 110 / 120 / 130 / 140 / 160 / 180 / 220 / 260 / 35080 / 90 / 100 / 120 / 140 / 180 / 240 / 280

TYPICAL AVAILABE HSS SOLAR & ECLIPSE SAW BLADES

The allround HSS solution

APPLICATIONS

PARAMETERS

MACHINES

All structural steel , non-alloy tool steel and stainless steel thin walled tubes. Tensile strength up to 600 N /mm2

Manual, automatic, flying cut-off applications

SteelAustenitic stainless steel (300 series)Ferritic without Ti (409 & 412) Ferritic with Ti (441)

Suggested cutting speed

Kinkelder BVCorporate Headquarters

Nijverheidsstraat 2(Industrial Area Zuidspoor)NL-6905 DL ZevenaarP.O. Box 242NL-6900 AE ZevenaarThe Netherlands

T: +31 (0)316 58 22 00F: +31 (0)316 58 22 17info@kinkelder.nlwww.kinkelder.com

Kinkelder USA SouthPell City (AL), USAT: +1 (205) 884 49 71info@kinkelderusa.comwww.kinkelderusa.com

Kinkelder FranceMessein, FranceT: +33 (383) 539713info@kinkelder.frwww.kinkelder.fr

Kinkelder Cutting Technology Co., Ltd.Suzhou City, ChinaT: +86 (0)512 693 68 780info@kinkelderchina.cnwww.kinkelder.com.cn

Kinkelder CuttingSolutions Inc.Louisville (KY), USAT: +1 (502) 329 8244cridge@kinkelderusa.comwww.kinkelderusa.com

AMV Service Le Chambon Feugerolles FranceT: +33 (477) 405229info@amvservice.comwww.amvservice.com

KTS Sägetechnik GmbHZülpich, GermanyT: +49 2252-835178-0info@kts-saegetechnik.dewww.kts-saegetechnik.de

Saws InternationalUSA HeadquartersMachesney Park (IL), USAT: +1 (815) 965 6900info@kinkelderusa.comwww.kinkelderusa.com

Kinkelder Belgium N.V./S.A.Sint-Pieters-Leeuw, BelgiumT: +32 (0)2 465 64 42info@kinkelder.bewww.kinkelder.be

KR SawsCoventry, United KingdomT: +44 (0)24 7661 0907sales@krsaws.co.ukwww.krsaws.co.uk

Kinkelder France SAOrchies, FranceT: +33 (320) 71 02 12sales@kinkelder.frwww.kinkelder.fr

Kinkelder Saw Inc. Canton (MI), USAT: +1 (734) 453 1199info@kinkelderusa.comwww.kinkelderusa.com

Sepio spol s.r.o.Zborovice, Czech RepublicT: +420 (0)57 366 91 35sepio@sepio.czwww.sepio.cz

or scan

D WNLOAD OURFREE APP NOW

Made in Holland www.kinkelder.com V 18.01 - HSS Standard Series