hp-2 / hp-4 wall wash recessed spackle & visible flange
TRANSCRIPT
HP-2 / HP-4 Wall Wash Recessed Spackle & Visible Flange Installation InstructionsOverview
1 of 12Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.comThis is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary.
© 2021 FINELITE, INC. ALL RIGHTS RESERVED. Form
- 98551 V3 EFFECTIVE DATE: 09/21
Kicker
Wall
Wall Wash Orientation
Step 1Rough-Ins & Mounting OptionsPages 2-3
Step 3Opening Luminaires
Page 5
Step 4Mounting Starter to StructurePages 6-7
Step 2Identification & PreparationPage 4
Step 7Closing Luminaires Pages 10-12
Step 5Joining LuminairesPage 8
Ceiling
Step 6Securing Luminaire JointsPage 9
• All power connections should be installed according to local/national codes by a Certified Electrician.
• This installation requires proper support as each luminaire is being installed.
• DO NOT attempt to join luminaires together on the floor. Damage may result when lifted.
NOTES
0-10V Dimming
SimplePlug-Together
Wiring
Universal &Robust Joints
HELPFUL VIDEOS
Prot
ecte
d by
one
or m
ore
US
Pate
nts:
891
5613
; D70
2,39
1; D
702,
390;
D70
0,73
2
2 of 12
HP-2 / HP-4 Wall Wash Recessed Spackle & Visible Flange Installation Instructions©
2021 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98551 V3 EFFECTIVE DATE: 09/21
Step 1 - Rough-Ins & Mounting Options
Z = Mounting Hole Location(Does not include endcaps)
HP-2 5"
HP-4 6"
Rough-In Lengths Rough-In Widths
W
L
X = Luminaire section length (Does not include endcaps)Y = Total run length of luminaire (Includes 1/8" for BOTH endcaps)Z = Mounting hole locationEndcap = 1/16"
Refer to Record Drawings and building plans to determine exact mounting, suspension points, and power feed locations.
* Tolerance +/- 1/16"
Spackle Flange (SF)
W
Visible Flange (VF)
W
• Use rough-in Length & Width dimensions and Record Drawings to determine rough-in measurements.• Build wall/ceiling with rough-in according to rough-in dimensions.• CRITICAL: Drywall or weak paneling must be secured to blocking (studs) around rough-in opening in
the wall/ceiling.
CONTINUED
L = Total Run Rough-In Length*Spackle Flange Visible Flange
HP-2 & HP-4 Y + 3/4" Y + 1/2"
W = Rough-In Width*Spackle Flange Visible Flange
HP-2 3-1/8" 2-1/2"
HP-4 4-7/8" 4-1/4"
* Tolerance +/- 1/16"
Mount Starter to Structure
Z Z Z Z
X2X1 X3Endcap
Starter Joiner EnderID: 1 ID: 2 ID: 3
Wal
l
Wal
l
Y
3 of 12
HP-2 / HP-4 Wall Wash Recessed Spackle & Visible Flange Installation Instructions©
2021 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98551 V3 EFFECTIVE DATE: 09/21
Step 1 - Rough-Ins & Mounting Options
1/4" Washer(by others)
1/4"-20 Nut(by others)
Mounting Option 1
Threaded Rod(by others)
¹ Wall/ceiling surface = drywall, wood, concrete or masonry, metal panels, tile, etc.² Support blocking = Wooden beams/studs, sheet metal framing beams, steel beams, concrete beams, etc. Use hardware appropriate to the beam material.
Mounting Options
Option 1 - Mount to Threaded Rod Option 2 - Mount to Structure
1/4"-20 Nut (by others)
1/4" Washer (by others)
1/4" Threaded Rod (by others)
Drywall Ceiling/Wall Drywall Ceiling/Wall
Structure Support (by others)
SupportBlocking2
(by others)
SupportBlocking2
(by others)
1/4" Lag Bolt (by others)
• Luminaire mounting holes sized for 1/4"-20 threaded rod.• Distance from threaded rod to wall/ceiling surface1 must be a minimum of 3-1/2".• Refer to Record Drawings to determine mounting hole locations on luminaires and install threaded rods to structure.
• Distance from support block to wall/ceiling surface1 must be a minimum of 4-1/8".• Refer to Record Drawings to determine mounting hole locations on luminaires and install support blocking² to structure.
3-1/2" min.4-1/8" min.
1/4"-20 Lag Bolt(by others)
Mounting Option 2
4 of 12
HP-2 / HP-4 Wall Wash Recessed Spackle & Visible Flange Installation Instructions©
2021 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98551 V3 EFFECTIVE DATE: 09/21
CAUTION
Arrange luminaires in order according to ID# at their install locations.
#10 x 1/2" ScrewPart# 92081Closing Luminairesp. 10, Step 7
1/4" WasherPart# 94082Opening Luminairesp. 5, Step 3Closing Luminairesp. 10, Step 7
#8-18 x 1/4" ScrewPart# 69026Opening Luminairesp. 5, Step 3Closing Luminairesp. 10, Step 7
Yoke BracketPart# 45042
#10-32 x 5/8" ScrewPart# 94144Securing Luminaire Jointsp. 9, Step 6
A. Identify Luminaires B. Remove Diffuser
Kitted Hardware
• Identify all luminaires by their ID label that can be found on the box, on the diffuser, and inside the luminaire. • NOTE: Exact location of labels in these areas may vary. • Remove all luminaires from their box.• Refer to Record Drawings that can be found in the hardware kit.
HP-6 VF - 8'
ABC Corporation - A12345HP-6-VF - 32' - S - 835 - F - 120V - SC - C1 - OBO
STARTER ID: 1 HP-6 VF - 16'
ABC Corporation - A12345HP-6-VF - 32' - S - 835 - F - 120V - SC - C1 - OBO
JOINER ID: 2 HP-6 VF - 23'
ABC Corporation - A12345HP-6-VF - 32' - S - 835 - F - 120V - SC - C1 - OBO
ENDER ID: 3
ABC Corporation - A12345
HP-4 WW-R - K - 32' - S - 835 - 120V - SC - C1
HP-4 WW-R - VF - X'ID: 1
STARTER
Lorem ipsumFactory Order NumberJob Name
Unique LuminaireID Number
Full Catalog Order ID
Luminaire Section Type
Luminaire Type and/or Run Length
• Finelite has provided items listed here, with their Finelite part numbers. These items can be found in separate boxes shipped with the luminaire.
• Account for all parts and set aside until they are needed.
• All other hardware needed for this installation will be by others.
Mud Guard
Diffuser
ID Label
HP-2
Kicker
Diffuser
1
2
Backplate
Putty Knife
• 1. Slide putty knife between the backplate and diffuser. • 2. Carefully separate diffuser from the backplate, keeping it inside its protective bag.• Set aside all diffusers to prevent from getting dirty or damaged.• Ensure diffuser can be clearly identified back to its corresponding luminaire.• CAUTION (Spackle Flange Only): Carefully remove Mud Guards and keep them as
they will be reinstalled in Step 7C.
• 1. Push bottom edge of the diffuser into backplate. • 2. Slide diffuser out of backplate.• Carefully remove and set aside all diffusers to prevent from getting dirty
or damaged.• Ensure diffuser can be clearly identified back to its corresponding luminaire.• CAUTION (Spackle Flange Only): Carefully remove Mud Guards and keep
them as they will be reinstalled in Step 7C.
Kicker
Diffuser
1
2
HP-4
Step 2 - Identification & Preparation
5 of 12
HP-2 / HP-4 Wall Wash Recessed Spackle & Visible Flange Installation Instructions©
2021 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98551 V3 EFFECTIVE DATE: 09/21
Step 3 - Opening Luminaires
#8-18 x 1/4" Screw(provided)
A. Release Backplates B. Remove Backplates
Backplate
1/4" Washer(provided)
• NOTE: If installing an independent, leave backplate installed and PROCEED TO STEP 4.• Release backplate from luminaire body by removing the #8-18 x 1/4" screw and
1/4" washer from both ends of the luminaire.• CAUTION: Set these screws and washers aside. Do not lose.
• NOTE: If installing an independent, leave backplate installed and PROCEED TO STEP 4.• Release backplate from luminaire body by removing the #8-18 x 1/4" screw from both
ends of the luminaire.• CAUTION: Set these screws aside. Do not lose.
#8-18 x 1/4" Screw (provided)
HP-4HP-2
#8-18 x 1/4" Screw (provided) 1/4" Washer (provided)
• Remove backplates by rotating then lifting up and out of the luminaire body.
• Keep backplate hanging with safety cables connected.
• Remove backplates by rotating then lifting up and out of the luminaire body.
• Keep backplate hanging with safety cables connected.
Backplate
HP-4HP-2
WALL SIDE
6 of 12
HP-2 / HP-4 Wall Wash Recessed Spackle & Visible Flange Installation Instructions©
2021 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98551 V3 EFFECTIVE DATE: 09/21
Step 4 - Mounting Starter to Structure
Jam Nut
Jam Nut
Splice Box
Conduit Plate
#8 Screw
Conduit Plate#8 Screw
Jam Nut
Conduit Plate
Starter
Conduit
CONTINUED
CONDUIT PLATE - ENDCAP (Standard)• Remove two screws holding conduit plate.• Install conduit and jam nut onto conduit plate.• Wire-nut electrical connections. See wiring legend above.• Reinstall conduit plate and screws. Do not damage any wires.
CONDUIT PLATE - TOP (Optional: HP-4 Only)• Remove screw holding conduit plate.• Install conduit and nut onto conduit plate.• Wire-nut electrical connections. See wiring legend above.• Reinstall conduit plate and screw. Do not damage any wires.
SPLICE BOX (Optional)• Lift tab to unsnap and remove splice box cover.• Install conduit and nut onto splice box cover.• Wire-nut electrical connections. See wiring legend above.• Reinstall splice box cover. Do not damage any wires.
Wire-nut electrical connections.
(Typical for all options.)WIRING LEGEND
Black Hot Line Voltage
White Neutral Line Voltage
Green Ground
Pink Dimming 0-10V DC
Purple Dimming 0-10V DC
A. Make Electrical Connections Electrical Connection Options
Flex Conduit(by others)
0-10V Dimming
• While properly supporting luminaire, maneuver luminaire near wall/ceiling opening.
• Make electrical connections at ENDCAP, at TOP or with a SPLICE BOX.
7 of 12
HP-2 / HP-4 Wall Wash Recessed Spackle & Visible Flange Installation Instructions©
2021 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98551 V3 EFFECTIVE DATE: 09/21
1/4" Washer(by others)
1/4"-20 Nut(by others)
Threaded Rod(by others)
Option 1 (Shown) - Mount to Threaded Rod• Align threaded rods with mounting holes and slide luminaire into wall/ceiling.• Install 1/4"-20 nut and 1/4" washer onto 1/4"-20 threaded rod.• CRITICAL: If installing a joiner luminaire in the next step, leave the nut loose,
allowing the luminaire to hang out of ceiling at an angle.• If there is no joiner/ender, then tighten nuts fully. PROCEED TO STEP 7.
Option 2 - Mount to Structure• Slide luminaire into wall/ceiling and mount to structure support with hardware
appropriate for the structure type.• CRITICAL: If installing a joiner luminaire in the next step, leave the bolt/screw
loose, allowing luminaire to hang out of ceiling at an angle.• If there is no joiner/ender, then tighten nuts fully. PROCEED TO STEP 7.
B. Mount Starter to Structure
Ceiling
Starter
1/4"-20 Threaded Rod (by others)
Drywall Ceiling Drywall Ceiling
Drywall Ceiling Drywall Ceiling
Option 1 (Shown) - Mount to Threaded Rod
Option 2 - Mount to Structure
1/4"-20 Lag Bolt(by others)
SupportBlocking(by others)
SupportBlocking(by others)
SupportBlocking
(by others)
SupportBlocking
(by others)
Structure Support (by others)
1/4"-20 Lag Bolt(by others)
Mounting Option 2Mounting Option 1
1/4"-20 Threaded Rod (by others)
1/4" Washer (by others)
1/4"-20 Nut (by others)
Step 4 - Mounting Starter to Structure
8 of 12
HP-2 / HP-4 Wall Wash Recessed Spackle & Visible Flange Installation Instructions©
2021 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98551 V3 EFFECTIVE DATE: 09/21
Option 1 (Shown) - Mount to Threaded Rod Option 2 - Mount to Structure
• Align joiner/ender with aligner sleeves on starter and slide together. Be careful not to damage any wiring.
• If necessary, lift both luminaires, then slide together.
B. Join Luminaires
Joiner/Ender
Starter
Aligner Sleeve
A. Mount Joiner/Ender to Structure
StarterJoiner/Ender
Ceiling
• Align threaded rods with mounting holes and slide luminaire into wall/ceiling.• Install 1/4"-20 nut and 1/4" washer onto 1/4"-20 threaded rod.• CRITICAL: If installing a joiner luminaire in the next step, leave the nut loose,
allowing the luminaire to hang out of ceiling at an angle.
• Slide luminaire into wall/ceiling and mount to structure support with hardware appropriate for the structure type.
• CRITICAL: If installing a joiner luminaire in the next step, leave the bolt/screw loose, allowing luminaire to hang out of ceiling at an angle.
CAUTION
DO NOT attempt to join luminaires together on the floor. Damage may result when lifted. Follow these instructions.
1/4" Washer(by others)
1/4"-20 Nut(by others)
Threaded Rod(by others)
1/4"-20 Lag Bolt(by others)
Mounting Option 2Mounting Option 1
Step 5 - Joining Luminaires
• While properly supporting luminaire, maneuver luminaire near wall/ceiling opening.• If necessary, loosen bolts on previous luminaire so that it can hang out of the opening at an angle.• After installing a joiner, return to previous luminaire and tighten.
9 of 12
HP-2 / HP-4 Wall Wash Recessed Spackle & Visible Flange Installation Instructions©
2021 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98551 V3 EFFECTIVE DATE: 09/21
SimplePlug-Together
Wiring
Universal &Robust Joints
Joiner/Ender
Starter
Yoke Screw (provided)
Aligner Sleeve
Yoke Bracket (provided)
1 Screwdriver with 6" bit required.
Yoke Bracket w/ Screw#10-32 x 5/8" (provided)
B. Make Electrical Connections A. Secure Joint with Yoke Brackets IN ALIGNMENT CORRECTLY INSTALLED
• Before installing yoke brackets, ensure the joining ends of luminaires meet flush and square.• CRITICAL: Ensure yoke brackets properly engage with aligner sleeves.• Secure joint by threading (but not yet tightening) yoke screws through yoke brackets and
into the aligner sleeves.• Tighten yoke screws¹ until joint seam of luminaires is closed.• Fully secure luminaire to structure by fully tightening the 1/4-20 nuts or lag bolts.
Luminaire Joint Luminaire Joint
YESNO
YOKE SCREW ALIGNMENT Bottom-Up View
Cross SectionView
Joiner/Ender
Starter
Plug-Together Wiring
Joiner/Ender Aligner Sleeve
Joiner/Ender Aligner SleeveLuminaire Joint
NOTE: Yoke screws should be installed directly across from each other, not diagonally, and in holes furthest from the joint line. One yoke screw per one yoke bracket. • Connect plug-together wiring.
Step 6 - Securing Luminaire Joints
10 of 12
HP-2 / HP-4 Wall Wash Recessed Spackle & Visible Flange Installation Instructions©
2021 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98551 V3 EFFECTIVE DATE: 09/21
Step 7 - Closing Luminaires
CONTINUED
#10 x 1/2" Screw(provided)
#8-18 x 1/4" Screw(provided)
1/4" Washer(provided)
A. Replace Backplates
HP-4HP-2
• 1. Carefully reinstall backplate into luminaire by inserting and rotating. • 2. Install joint cover plate by inserting into backplate and installing two #8-18 x 1/4"
screws at the joint. PROCEED TO STEP 7C
Joint Cover Plate
2
Joint Cover Plate
WALL SIDE
Backplate
1
Backplate
• 1. Carefully reinstall backplate into luminaire by inserting and rotating. • 2. Install 1/4" washer and #8-18 x 1/4" screw to backplate at both ends of luminaire.
1 2
Backplate
B. Secure Joint with #10 x 1/2" Screws
• Install 1/4" washers and #10 x 1/2" screws at the joint.
HP-4 Only
#8-18 x 1/4" Screw (provided)
1/4" Washer (provided)#10 x 1/2" Screw (provided)
1/4" Washer (provided)
11 of 12
HP-2 / HP-4 Wall Wash Recessed Spackle & Visible Flange Installation Instructions©
2021 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98551 V3 EFFECTIVE DATE: 09/21
Step 7 - Closing Luminaires
C. Secure Flange To Structure D. Apply Spackle
• Secure flanges to wall/ceiling using appropriate screws or fasteners1 for hard surface, per local building codes.• Install the "mud guard" cardboard inserts to help prevent spackle and paint from getting into the luminaire.
• Spackle and paint over flanges up to luminaire edge.• CAUTION: Careful not to drop spackle into luminaire. Immediately wipe off excess spackle that may have gotten onto luminaire edges.• Perform all spackling and painting to walls and ceiling prior to removing mud guards.• Remove all mud guards.
Every 6" to 12"
Mud Guard (provided)
Mud Guard (provided)
Putty Knife
Spackle
Ceiling
Ceiling
WallWall
Spackle Flange Only Spackle Flange Only
1 Screws or fasteners: drywall - drywall screws, wood - wood screws, etc.
Screw/Fastener(by others)
CONTINUED
Screw (by others)
12 of 12
HP-2 / HP-4 Wall Wash Recessed Spackle & Visible Flange Installation Instructions©
2021 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98551 V3 EFFECTIVE DATE: 09/21
ID: 1
ID: 1
ID: 2
ID: 2
ID: 3
ID: 3
E. Final Step - Replace Diffusers
• NOTE: If your installation includes a battery backup, please see addendum (98333) that should be included with your kitting package.• Remove diffusers from protective plastic bag.• CAUTION: Wear gloves to keep diffuser surface clean.• CRITICAL: Be sure to install correct diffuser to its corresponding luminaire ID.• Install diffusers into luminaire body, ensuring they are in place.• 1. Reinstall diffusers by pushing right side of the diffuser into the backplate.• 2. Push the left side of diffuser until it lays flat on the backplate.• Turn power on to luminaire.
1
2
HP-4
• NOTE: If your installation includes a battery backup, please see addendum (98333) that should be included with your kitting package.• Remove diffusers from protective plastic bag.• CAUTION: Wear gloves to keep diffuser surface clean.• CRITICAL: Be sure to install correct diffuser to its corresponding luminaire ID.• Install diffusers into luminaire body, ensuring they are in place.• 1. Slide the side of the diffuser without a notch into the luminaire.• 2. Push the side of the diffuser that has a notch until click sound is heard.• Turn power on to luminaire.
HP-2
12
Step 7 - Closing Luminaires