How to Hack Wi-Fi: Breaking a WPS PIN to Get the Password with

Bullyhttp://null-byte.wonderhowto.com/how-to/hack-wi-fi-breaking-wps-pin-get-password-with-bully-0158819/

Welcome back, my nascent hackers!

Like anything in life, there are multiple ways of getting a hack done. In fact, good

hackers usually have many tricks up their sleeve to hack into a system. If they

didn't, they would not usually be successful. No hack works on every system and

no hack works all of the time.

I have demonstrated many ways to hack Wi-Fi here on Null Byte, including

cracking WEP and WPA2 passwords and creating an Evil Twin and Rogue AP.

A few years back, Alex Long demonstrated how to use Reaver to hack the WPS

PIN on those systems with old firmware and WPS enabled. Recently, a new WPS-

hacking tool has appeared on the market and is included in ourKali hacking

distribution. It's name, appropriately, is Bully.

Why WPS Is So Vulnerable

WPS stands for Wi-Fi Protected Setup and was designed to make setting a secure

AP simpler for the average homeowner. First introduced in 2006, by 2011 it was

discovered that it had a serious design flaw. The WPS PIN could be brute-forced

rather simply.

With only 7 unknown digits in the PIN, there are just 9,999,999 possibilities, and

most systems can attempt that many combinations in a few hours. Once the WPS

PIN is discovered, the user can use that PIN to find the WPA2 preshared key

(password). Since a brute-force attack against a WPA2 protected AP can take

hours to days, if this feature is enabled on the AP and not upgraded, it can be a

much faster route to getting the PSK.

The Keys to Success

It's important to note, though, that new APs no longer have this vulnerability. This

attack will only work on APs sold during that window of 2006 and early 2012. Since

many families keep their APs for many years, there are still many of these

vulnerable ones around.

If you aren't familiar with wireless hacking, I strongly suggest that you read

my introduction on the Aircrack-ng suite of tools. In addition, make certain that you

have an Aircrack-ng compatible wireless card, otherwise this will simply be an

exercise in frustration.

Step 1: Fire Up KaliLet's start by firing our favorite hacking Linux distribution, Kali. Then open a

terminal that looks like this:

To make certain we have some wireless connections and their designation, we can

type:

kali > iwconfig

As we can see, this system has a wireless connection designated wlan0. Yours

may be different, so make certain to check.

Step 2: Put Your Wi-Fi Adapter in Monitor Mode

The next step is to put your Wi-Fi adapter in monitor mode. This is similar to

promiscuous mode on a wired connection. In other words, it enables us to see all

the packets passing through the air past our wireless adapter. We can use one of

the tools from the Aircrack-ng suite, Airmon-ng, to accomplish this task.

kali > airmon-ng start wlan0

Next, we need to use Airdump-ng to see the info on the wireless AP around us.

kali > airdump-ng mon0

As you can see, there are several APs visible to us. I'm interested in the first one:

"Mandela2." We will need its BSSID (MAC address), its channel, and its SSID to be

able to crack its WPS PIN.

Step 3: Use Airdump-Ng to Get the Necessary Info

Finally, all we need to do is to put this info into our Bully command.

kali > bully mon0 -b 00:25:9C:97:4F:48 -e Mandela2 -c 9

Let's break down that command to see what's happening.

mon0 is the name of the wireless adapter in monitor mode. --b 00:25:9C:97:4F:48 is the BSSID of the vulnerable AP. -e Mandela2 is the SSID of the AP. -c 9 is the channel the AP is broadcasting on.

All of this information is available in the screen above with Airdump-ng.

Step 4: Start Bully

When we hit enter, Bully will start to try to crack the WPS PIN.

Now, if this AP is vulnerable to this attack, bully will spit out the WPS PIN and the

AP password within 3 to 5 hours.