how to configure cisco uc500 series (basic configuration) to configure cisco uc500 series.pdf ·...

Copyright © 2011 Sakun Sharma (www.sakunsharma.in)

How to Configure Cisco UC500 Series

(Basic Configuration)

Cisco Unified Communication Manager 500 Series can be configured using Cisco Configuration

Assistance which comes in CD with UC500 or can be downloaded from Cisco Official Site.

Follow the following setups to configure UC500:

1. Connect Ethernet cable from any of 8 IP Phone ports to your laptop or machine ethernet

adapter.

2. Set IP configuration of adapter to Obtain IP from DHCP (as DHCP is enabled by default for IP

Phone Ports).

3. It will obtain IP in network of 192.168.10.x, as shown below:

4. Now start Cisco Configuration Assistant (CCA).

5. Connect to UC500 using IP Address: 192.168.10.1 (which is your gateway).


6. Now before you connect to UC500, you need to enter username and password. So to create

username and password you have to connect to console via Serial Cable and via Hyper Terminal

enter following command in global configuration mode (entered via entering command

configure terminal):

username admin password cisco 15

7. Now login into UC500 with the credentials created in above command:

a. Username: admin

b. Password: cisco

c. Privilege Level: 15

8. You will come up with Telephony Setup Wizard. Close this wizard as we will setup manually.

9. Now we have to configure exchange, on left panel, go to: Telephony � Users and Extensions �

Users and Phones.


10. Now when you click Users and Phones, and dialog appears like shown below which ask you for

Telephony Initialization.

11. As per your wish you can enter Number of Digits Per Extension and Voicemail Access

Extension. (I have entered 3 Digits per Extension and 200 as Voicemail Access Extension).

12. At this point, you exchange is ready to connect IP phones.

13. Now connect IP Phone to one of the IP Phone Port at front panel of UC500.

14. If you don’t have IP Phone and want to configure using some software which acts as IP Phone,

you can use Cisco IP Communicator (CIPC) Software. All the configuration show ahead is using

Cisco IP Communicator as IP Phone.


15. Install Cisco IP Communicator (CIPC) on your laptop and other machines you want to make call.

When you install CIPC, you can see Cisco Discovery Protocol (CDP) Packet Driver installed in

your ethernet adapter settings. (IP Phones use CDP protocol to discover other voice devices)

16. When you start CIPC, your phone will automatically discover UC500 in network using CDP and

register itself to it.

17. When phone registers itself with exchange, exchange displays messages on terminal as shows

below:


18. At this moment, phone is registered to exchange, but to make it working you have to configure

phone with extension number and some other configurations. To configure phone, navigate to

Users and Phone in Cisco Configuration Assistant (CCA).

19. There you will see this phone in list but un-configured. Select this phone and click on Edit.

20. In edit mode enter the required information for this phone. I have entered information as

shown below:


21. After entering the required information click “OK”. Extension Number entered above “201” is

the phone number for this phone.

22. When configured successfully, it will show full information in Users and Phone list as shown

below:

23. At this moment phone is ready for use with extension number 201.

24. On IP phone you can see the changes, it will now show its extension number and description of

the phone configured in CCA as shown below:


25. In similar manner you can configure another IP Phone or CIPC for testing purpose. I am attaching

few screenshots of second CIPC phone configurations.


26. At this moment, both phones are ready to make call. So make a test call between these two

phones. Make a call from phone DSharma 202 to Sakun 201.


27. You can see topology by clicking Topology and see exchange topology as shown below:

28. Now save configuration by navigating to Save Configuration, last option in CCA left panel and

save configuration for all devices.

how to configure cisco uc500 series (basic configuration) to configure cisco uc500 series.pdf ·...

Documents