how to build your playhouse. september 08, 2006 by kay adams, tamecha buck, janet herron & lisa...
TRANSCRIPT
How to Build Your Playhouse.
September 08, 2006By Kay Adams, Tamecha Buck, Janet Herron &
Lisa Weston
“Click on pictures”
Introduction
Building a playhouse for your children should be both fun and easy. We have designed all of our kits to contain everything you need with minimum assembly. Here are a list of the tools and site preparation you will need for a smooth process:
Building Construction
All kits are already cut and finished to your package specifications. Railing, steps, trim, posts and roof vents are sent separate from the building kit. Sill plates are pre-drilled to allow anchor bolts to be attached to the slab.
Required Tools
Power Drill
#2 Phillips head drill bits
½” Concrete drill bit
Square
Chalk line
Ruler
Shims
Hammer
Pry bar
½” Socket wrench
(4) 2”x4”x12” studs
4’ Level – used to plumb
Hardware package included with kit
Building a Playhouse
First, gather directions listed under the “lessons” tab of this Web site
Look at the list of “required tools” and make sure you have them
Obtain “hardware package” –included with kit
Building a playhouse (con’t)
First prepare site playhouse will be built upon-remember twice as large as the house
Slab preparation
Plumbing
Electrical
Building a playhouse (con’t)
Build form for slab. Make sure corners are square and that apron will have a ¼” drop per foot away from the building.
Position 6x6 10/10 WWM. (Woven Wire Mesh) where slab will be poured
Slab Preparation
Excavate 12” deep around entire building site
Place electrical hook-ups and rough plumbing where desired
Lay drainage pipe around perimeter-at least 12” away from building for drainage
Cover drainage tile with roofing felt to prevent clogging of drainage holes
Cover entire site with peas gravel 6” deep
Place 2” of sand on top of gravel, level and compact
Use 4 mil plastic to cover compacted area
Use 2x4’s to form slab – make sure there is at least ¼” fall per foot
Spread wire mesh within the formed area
Pour 4” of concrete over wire mesh
Assembly
Use ruler and chalk line to mark wall placement – make sure they are square.
Start assembly with back wall - Mark pre-drilled holes on slab – Drill holes at least 3” deep – place wall over drilled holes and screw in the 6” anchor bolts provided – screw temporary studs high on each end of the wall and anchor them to the ground for support.
Place either the left or right wall on the inside of the back wall and mark and drill the holes as above. After wall is in place, hand tighten the anchor bolts. Check for plumb and square before attaching wall completely.
Repeat process for other wall.
Assembly (con’t)
Place front wall to match up with side walls. Mark and secure wall as above.
Remove all support studs and replace all trim if applicable.
Temporarily place railings on slab as indicated in drawing. Square them to the building and mark the slab where posts are to go. Drill holes and secure anchor bolts. Secure railings to anchors and attach with provided screws.
Lift half of roof into position ensuring the notched rafters are resting on the top of the double top plate on one of the side walls. Toe nail the roof section and repeat same process with other half of roof.
Attach ridge vent to peak
of roof and secure.
Assembly (con’t)
Anchor posts to slab.
Place front steps between opening in railing at the front of the slab if needed and secure in place.
Backfill site if needed.
Remove all packing from windows and doors.
Complete any optional features.
Playhouse is complete and ready
to be used.
Conclusion
Please contact us at http://www.Building4Kids.com with any questions you may have.
We appreciate your business and hope you are satisfied with the craftsmanship and quality of your new playhouse.
E-Assessment
How do you like this site?_____
Is this site informative?_____
Is this site user friendly?______
Do all navigation buttons function?______
Do most pictures have some sort of animation that works?____
Do you have any suggestions?_____
Thank you for viewing this site!