hilti fs manual

Firestop SystemsGuide for Specifiers2007 Edition

Fir

esto

p S

yste

ms G

uid

e f

or

Sp

ec

ifie

rs

20

07

Ed

itio

n

In the US: P.O. Box 21148 Tulsa, OK 74121Customer Service: 1-800-879-8000en español: 1-800-879-5000Fax: 1-800-879-7000

www.us.hilti.com

Hilti is an equal opportunity employer.Hilti is a registered trademark of Hilti, Corp.©Copyright 2007 by Hilti, Inc. (U.S.)H181 • 3427488 • 07/07 • DBS

The data contained in this literature was current as of the date of publication. Updates and changes may be madebased on later testing. If verification is needed that the data is still current, please contact the Hilti Technical SupportSpecialists at 1-800-879-8000. All published load values contained in this literature represent the results of testingby Hilti or test organizations. Local base materials were used. Because of variations in materials, on-site testing isnecessary to determine performance at any specific site. Laser beams represented by red lines in this publication.Printed in the United States

*14001 US only

In Canada: 6790 Century Avenue, Suite 300CDN-Mississauga, Ontario L5N 2V8 Customer Service: 1-800-363-4458Fax: 1-800-363-4459

www.hilti.ca Saving lives through innovation and education.Hilti. Outperform. Outlast.

Engineering Judgment Request Form

Hilti, Inc. (U.S.) 1-800-879-8000 • www.us.hilti.com • en español 1-800-879-5000 • Hilti Firestop Systems Guide 2007

Hilti. Outperform. Outlast.

Hilti FirestopSaving Livesthrough innovationand education

Date submitted (MM/DD/YY)

Initiator’s Name

DDAATT or Phone Fax

Project Name

Contractor Contact

Phone Fax

TP Through Penetration

1. Type and thickness of wall or floor penetrated:

2. Type and size of penetrating item(s):

3. Size and shape of opening:

If sleeved, specify type and size:

4. Annular space (min. and max.):

5. Fire rating (hrs.):

J Joint

1. Type and thickness of wall or curtain wall

(include stud size for gyp):

2. Type and thickness of floor or floor/ceiling assembly

(include flute size):

3. Orientation of wall to floor/ceiling assembly (circle one):

Perpendicular Parallel

4. Type of joint system (circle one):

Floor-to-floor Floor-to-wall Top-of-wall

Wall-to-wall Curtain wall

5. Maximum width of joint:

6. Fire rating (hrs.):

Comments:

Fax completed form to Hilti Fire Protection Engineering Team for processing : 918-254-1679

l TP Through Penetration OR l J Joint

PROFIS Firestop



Hilti FirestopSaving Lives through innovation and education

Hilti Professional Integrated Software has been developed to aid in the

selection, specification and submittal of tested and approved Hilti

firestop systems that meet today’s tough building codes.

PROFIS Firestop features:

• Comprehensive, easy-to-use interactive system selector

• Database of exportable, tested and approved firestop systems

drawings and installation instructions

• Complete submittal builder feature which outputs a customized,

professional-looking submittal package that includes the following:

• Cover page stating who the submittal was created for and the

project information

• Table of contents

• Product information page(s)

• Certificate(s) of Compliance

• System(s) drawings complete with installation instructions

• Material Safety Data Sheet(s)

Specify and submit with confidence when using PROFIS Firestop. This

easy-to-learn, powerful software makes specifying and installing the

correct firestop systems for your project fast and accurate.

Introducing PROFIS Firestop

Hilti PROFIS Firestop software will be available soon!To request your free copy of this powerful software either:

Call your Hilti Customer Service Representative at 1-800-879-8000

Register online at www.us.hilti.com and email your request

OR

Contact your local Hilti Account Manager


Hilti. Outperform. Outlast.1

Firestop Design Center

Firestop specification made easy!

Access a state-of-the-art tool designed to make specification of Firestop even easier with the click of a mouse. Designed with you in mind,the Hilti Firestop Design Center makes solving application problems and downloading CAD-ready drawings easy.

Access our complete library of detailed drawings and specifications by registering today at www.us.hilti.com.

Once there, you will find:

• Sample specifications

• System drawings

• Product information

• Firestop terms and definitions

• Building regulations and codes

• Project references

• Firestop FAQ

Additional Resources• In-house, full-time degreed Fire Protection Engineers

• Hilti Systems & Solutions — Full Line Product Catalog

• Hilti Product Technical Guide

Visit the Hilti Firestop Design Center Online today at www.us.hilti.com

(click on the “Specification” link under “Planning & specifying”)

➊ Search by application: Joints or Through Penetrations

➋ Design & Specification Resources

➌ System Drawing Search

➍ Featured New Products

1 2

34

Continuing Education CourseCourse name: Firestop — A Life Safety Issue

• Provides one hour of AIA and state credit

• Qualifies for HSW

• FREE

Presented by: Chad Stroike, CFPS, Hilti, Inc.

Description: Provides an overview of fire safe building construction,how to provide proper firestop protection via model building codes,and specifications. Proper and improper firestop installations, liabilityissues, and types of fire/smoke assemblies are also reviewed.

To take this course: www.aecdaily.com/en/1595881

Firestop Specialty Contractors

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s

2

Hawaii

Hilti Accredited Firestop Specialty Contractors*Hilti Fire Protection Specialists

A Hilti Accredited Firestop SpecialtyContractor (HAFSC) is an independent professionalfirestop installer who has been provided specializedtraining by Hilti; and who has committed to provide

building owners, generalcontractors, and subcontractorswith a full service solution for alltheir firestopping needs. When youchoose to use a Hilti AccreditedFSC, you are selecting a trainedfirestop installationspecialist committed to applyingproven Hilti firestopping technology

and innovation in your building to minimize the risk ofloss due to fire, smoke, and toxic gases.

Hilti Accredited FSCs useHilti firestop products,which eliminates theconfusion caused bynumerous subcontractorsinstalling different firestopproducts on the same job. This also providescontinuity throughout the job, which helps reduceyour liability exposure. Their professionalexpertise in installing the appropriate Hilti firestopsystem can provide significant savings potential in timeand cost to the general contractor and building owner.

During firestop inspections, Hilti Accredited FSCs canoffer documented, step-by-step accountability. Theirfirestop expertise helps assure building officials thatthe proper installation techniques have been appliedand that all installed systems comply with localand national codes.

CONTAINMENT

SUPPRESSIONDETECTION

• Hospitals

• Nursing Homes

• Schools

• Universities

• Office Buildings

• Apartment Complexes

• Retail Centers

• Telecom Switching Stations

• Telecom Central Offices

• Entertainment Complexes

• Hotels

• Petroleum Plants

• Chemical Plants

• Nuclear Power Plants

• Pharmaceutical Plants

• Military Complexes

For a Hilti Firestop Specialty Contractor near you, call 1-800-879-8000 today.

Through the Firestop Specialty ContractorProgram, Hilti trains professional contractors in fireprotection systems installation procedures of Hilti productsthat meet all current standards and codes. For Architects andSpecifiers this is great news. By using a Hilti AccreditedFirestop Specialty Contractor (HAFSC) you get factory-trained professionals who are knowledgeable aboutfirestopping methods and quality installations.

Selecting a HAFSC has the following benefits:

• Allows tradespeople to focus on their area of expertise,leaving firestopping to passive fire protection specialists

• Help ensure one-source continuity and systemcompatibility for all firestop applications

• Promote hassle-free inspection by officials who know andtrust professional firestop installers

• Provide single contractor accountability for all firestopapplications

• Increase your confidence that all firestopping is completedcorrectly the first time

* Hilti Accredited Firestop Specialty Contractors are independent companies who have hademployees participate in the Hilti firestop training program.




3

Intro

ductio

nC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

Firestop Systems Guide

Introduction Page 3

Dedicated to Life Safety Page 4

Application Review, Products and Selection Chart Page 9

Firestop Systems Application Review Page 10Product Information & Installation Instructions Page 14

Product Ordering Information Page 37Selection Chart Page 44

Firestop System Drawings 8

Most Common Systems Directory Page 58Alpha-Numeric System Directory Page 511

Through-Penetration Drawings Page 60Joint Drawings Page 356

Estimating Tables & Technical Data Page 463

Estimating Tables Page 465Firestop Terms & Definitions Page 469

Understanding System Nomenclature Page 471Material Safety Data Sheet (MSDS) Page 472

UL Certificates of Compliance Sheets Page 506Terms and Conditions of Sale Page 510

Engineering Judgment (EJ) Process & Form Page 512

Dedicated to Life Safety

Intr

od

uctio

nC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




4

Hilti is dedicatedto saving lives throughinnovation andeducationThe quality and excellence of HiltiFirestop products help ensurethat fire, smoke and toxic gasesare contained to reduce the tragicloss of human life and property.Through a combination ofsuperior products, advancedknowledge and unparalleledcustomer service we are able toprovide the highest qualityfirestop systems.

Hilti offers a comprehensive support packageThroughout the entireFirestopping process, whether itis specification, installation orinspection, Hilti will be there tooffer job site support andexpertise. The Hilti highly trainedSales Force, Fire ProtectionSpecialists, and in-house FireProtection Engineering team canhelp you select the correctproducts and systems to matchyour specific project needs. Hiltihas a support package that isunmatched in the passive firestopindustry.

Fire safetyFire safety is a major concern for allwho are responsible for the design andspecification of new buildings.

The causes of fire are varied andunpredictable, and often outside thecontrol of the designer. What can becontrolled, however, is the effect of fireonce it has started.

The control of fire within a building isnormally affected by a combination ofactive and passive fire protection systems.

Active fire protection systemsActive fire protection systems are designedto detect fire, and either to extinguish it bymeans of water sprinklers, halogeninstallations or fire extinguishers, or tominimize its effects by smoke ventilation.Active systems are also used to assist theescape of occupants by the provision ofalarms and emergency lighting.

Passive fire protection systemsPassive fire protection is designed intothe structure of the building, so that iffire breaks out, it is contained within afire compartment, surrounded by fire-resistive walls and floors. For the wallsand floors to maintain their fire-resistance, however, every opening,penetration and joint must be sealedagainst the escape of fire and smoke.

Intumescent fire sealsThe materials used to form the seals mustnot only fill all gaps at the time ofconstruction, but also, in the event of fire,expand to close any further gaps formed bymelted components. These intumescent fireseals, if properly installed, can help preventfire escaping from a compartment for arating period of up to four hours. This timeperiod can prove vital in allowing occupantsto escape, and fire-fighters to control the fire.

HiltiAround the world the red Hilti toolbox isa familiar sight on building sites, andthe Hilti name is known and respected.

To most people Hilti means precision toolsand secure fastenings. For many years

however, Hilti has applied their skills to anew area of construction where precisionand security are vital: firestopping.

Hilti firestop systemsThe aim of Hilti firestop systems is toprovide designers and specifiers withthe following:• excellence — finished solutions

that match the well known, highquality standards associated with theHilti product

• easy installation — all firestopcomponents are readily available andsimple and fast to install

• tested and used world wide— Hilti offers ‘one-stop’ firestoppingsystems tested in accordance withmost relevant regulations

• wide ranging solutions — forvirtually any opening or penetrationthrough which heat or smoke might pass,Hilti offers a firestop solution that will helpminimize damage in the event of a fire

Hilti and thedesigner/specifierTo assist the designer or specifier inselecting and specifying the appropriatefirestop system, Hilti has developed twotools; PROFIS Firestop and the onlineFirestop Design Center.

PROFIS Firestop is a professionallyintegrated software that guides youthrough the system selection process.Once the appropriate system isselected, the software generates aprofessional looking submittal packagewith all the necessary documents.

The online Firestop Design Centerallows you to access specification toolsand resources by application or byproduct names. To visit the onlineFSDC, go to www.us.hilti.com and clickon the “Specifications” link. Then, followthe “Firestop Design Center” link to theright of the page.

Hilti customized solutionsIf none of the standard firestop systemsmeet the requirements of the design,Hilti is ready to offer their expertise andwork with the designer to producecustomized solutions.

Fire Safety Issues



Intro

ductio

nC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

Problem The illustration on the left indicates a rangeof typical problems facing the designer.

Construction may consist of:

• concrete • wood • gypsum

The problem areas are:

Movement jointsRigid or low movement jointsHead of wall and perimeter jointsMetal and plastic pipesPlastic pipesMultiple penetrations, pipes and/orcablesCable trays (with permanent sealingof opening during construction, ortemporary sealing allowing additionalcables to be installed subsequently)Cable trays (with permanent sealingof opening during construction)Cables (single or bundled)Electrical outlet boxesHeating/ventilation/air conditioning

Fire Resistance RatingTo help prevent the rapid spread of firewithin a building, certain walls, floorsand joints are required to meet a specificfire resistance rating — the period oftime during which a building componenthas been tested to confine a fire orcontinue to perform a structural functionor both. Through-penetrations and jointscreated during the construction processrequire the installation of firestopsystems in order to bring the wall orfloor back up to its original fire-rating.

FirestoppingIt is essential that every penetration orjoint in a fire-rated wall or floor isadequately protected by sealing — or“firestopping” — such that the buildingcomponent is restored to its original fire-rated condition in order to maintaincompartmentalization. The quality andexcellence of Hilti Firestop Products helpensure that fire, smoke and toxic gasesare contained to reduce the tragic lossof human life and damage to property.

11

10

9

8

7

6

5

4

3

2

1

3

7

11

3

8

96

1

4

5

2

10

Hilti Firestop Solutions

Intr

od

uctio

nC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s



Hilti firestop systems are suitablefor use with constructions of:

Concrete or concrete blockGypsumWoodW

G

C

Hilti Firestop SolutionsFor each of the firestopping problems illustrated on the facingpage, Hilti has designed and tested a specific solution. Notonly is there a solution for each type of opening, but Hilti alsooffers a choice of firestop systems for several applications,according to the size of the opening and whether theinstallation is permanent or temporary.

Hilti Product Description Application F rating Page

Metallic & Non-metallic Pipes

CP 680-P/M Cast-in Firestop Device Metal and plastic pipes with diameters up to 6" up to 4 hours 14CP 620 Fire Foam Metal and plastic pipes (in conjunction with CP 648-E) up to 3 hours 24CP 644 Firestop Collar Plastic pipes with diameters 8" to 10" up to 2 hours 32CP 643N Firestop Collar Plastic pipes with diameters 6" or less up to 4 hours 31FS-ONE Intumescent Firestop Metal and plastic pipes up to 4 hours 20CP 604 Self-Leveling Firestop Sealant Metal pipes up to 3 hours 23CP 648-S Firestop Wrap Strip Single wrap for plastic pipes up to 3 hours 33

Cables & Cable Trays

CP 680-P/M Cast-in Firestop Device Cable bundles up to 3 hours 14CP 658T Firestop Plug Single or bundled cables up to 4 hours 30CP 675T Firestop Board Temporary and permanent sealing of cables and cable trays up to 2 hours 27CP 620 Fire Foam Permanent sealing of cables and cable trays up to 2 hours 24FS-ONE Intumescent Firestop Jacketed cables and cable bundles up to 4 hours 20FS 657 Fire Block Temporary and permanent sealing of cables and cable trays up to 4 hours 26CP 637 Firestop Mortar Permanent sealing of cables and cable trays up to 4 hours 25CP 618 Firestop Putty Stick Single or bundled cables up to 4 hours 29CP 617-L/XL Firestop Putty Pad Electrical boxes up to 2 hours 28CP 604 Self-Leveling Firestop Sealant Cable bundles up to 3 hours 23

Multiple Penetrations

CP 648-E Firestop Wrap Strip Continuous wrap for plastic pipes up to 4 hours 34CP 648-S Firestop Wrap Strip Single wrap for plastic pipes up to 2 hours 33CP 620 Fire Foam Permanent sealing of metal and plastic pipes, up to 2 hours 24

cables, and cable traysFS-ONE Intumescent Firestop Metal and plastic pipes, jacketed cables and cable bundles up to 3 hours 20FS 657 Fire Block Temporary and permanent sealing of metal up to 4 hours 26

and plastic pipes, cables and cable traysCP 637 Firestop Mortar Permanent sealing of metal and plastic pipes up to 4 hours 25

cables and cable traysCP 680-P/M Cast-in Firestop Device Multiple metallic and non-metallic pipes up to 3 hours 14CP 675T Firestop Board Temporary and permanent sealing of cables, cable trays up to 2 hours 27

and metal pipes

Heating / Ventilation / Air-conditioning

FS-ONE Intumescent Firestop Sealing around metal ducts up to 3 hours 20CP 601S Elastomeric Firestop Sealant Sealing around metal ducts up to 3 hours 21CP 606 Flexible Firestop Sealant Sealing around metal ducts up to 3 hours 22CP 604 Self-Leveling Firestop Sealant Sealing around metal ducts up to 3 hours 23

Joints/Curtain Walls

CP 606 Flexible Firestop Sealant Sealing floor joints, head of wall and wall to wall joints up to 3 hours 22CP 601S Elastomeric Firestop Sealant Sealing floor, head of wall and wall to wall joints up to 4 hours 21CP 604 Self-Leveling Firestop Sealant Sealing floor to wall joints (Perimeter/Curtain Walls) up to 2 hours 23CP 672 Speed Spray Sealing head of wall, wall to wall and floor to walls up to 4 hours 35

(Perimeter/Curtain Walls)CP 767/777 Speed Plugs/Speed Strips Provides non-combustible backing for FS sealants - 3614

13

9

7

7

9

7

7

7

11

1

4

3

7

8

12

12

9

6

5

4

3

7

8

11

10

1

12

9

7

2

2

8

1

Hilti Firestop Solutions




7

Intro

ductio

nC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

Hilti Firestop SolutionsThe illustration on the right provides abasic guide to the range of HiltiFirestop products available for theapplications shown

CP 680-P/M Firestop Cast-InDevice

CP 643N Firestop CollarCP 644 Firestop Collar FS 657 Fire BlockCP 637 Firestop MortarCP 618 Firestop Putty StickCP 617 / CP 617L / CP 617XLFirestop Putty PadFS-ONE High Performance

Intumescent SealantCP 601S Elastomeric Firestop

SealantCP 606 Flexible Firestop SealantCP 620 Fire FoamCP 604 Self-Leveling Firestop

SealantCP 658T Firestop PlugCP 675T Firestop BoardCP 648-E/S Firestop Wrap StripCP 672 Speed SprayCP 767 Speed StripsCP 777 Speed Plugs

14

13

12

11

10

9

8

7

6

5

4

3

2

1

7

4

85

12

6

3

11 13

14

9

7

77

10

1

2

9

9

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s

9

Chap

ter T

ab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

Applications/Products

Firestop Systems Application Review Page 10

Product Information & Installation Instructions

CP 680-P Cast-In Firestop Device Page 14CP 680-M Cast-In Firestop Device Page 14

Height Extension Page 15Metal Deck Adapters Page 15Water Barrier Module Page 16

Top Seal Plug Page 16CP 681 Tub Box Kit Page 17

Closet Stub Page 18Shower and Floor Drain Page 19

Aerator Adapter Page 19FS-ONE High Performance Intumescent Firestop Sealant Page 20

CP 601S Elastomeric Firestop Sealant Page 21CP 606 Flexible Firestop Sealant Page 22

CP 604 Self-Leveling Firestop Sealant Page 23CP 620 Fire Foam Page 24

CP 637 Firestop Mortar Page 25FS 657 Fire Block Page 26

CP 675T Firestop Board Page 27CP 617, CP 617 L and CP 617 XL Firestop Putty Pad Page 28

CP 618 Firestop Putty Stick Page 29CP 658T Firestop Plug Page 30

CP 643N Firestop Collar Page 31CP 644 Firestop Collar Page 32

CP 648-S Firestop Wrap Strip Page 33CP 648-E Firestop Wrap Strip Page 34

CP 672 Speed Spray Page 35CP 777 Speed Plugs Page 36CP 767 Speed Strips Page 36

Hilti FACT Program Page 37

Product Ordering Information Page 38

Selection Chart Page 44

Product Information

Chap

ter

Tab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s



Firestop SystemsApplication Review

Me

tal p

ipe

s

Pla

stic

/gla

ss p

ipe

s

Ca

ble

s/c

ab

le t

rays

Insu

late

d m

eta

l pip

es

Me

tal d

uc

ts

Mu

ltip

le p

en

etr

atio

ns

Join

ts

Application

See Page Description Features Benefits

CP 680-PCast-InFirestop DeviceA one-step cast-in firestopdevice for a wide varietyof pipe materials anddiameters

• Quick and simple installation

• Integrated moisture and smokeseal

• Tested in concrete floorthicknesses from 2-1/2" (63 mm)

• Innovative adapter for metal deckapplications

• Ready to use — no additionalcaulk required

• Easy to specify, install and inspect

• Cost effective solution

CP 680-MCast-InFirestop DeviceA one-step cast-in firestopdevice for a wide variety ofnon combustible pipematerials and diameters

• Quick and simple installation

• Integrated moisture and smokeseal

• Tested in concrete floorthicknesses from 2-1/2" (63 mm)

• Innovative adapter for metal deckapplications

• Ready to use — no additionalcaulk required

• Easy to specify, install and inspect

• Cost effective solution

HeightExtension For use with CP 680-P/M

• One extension adds up to 6"

• For concrete floors over 8"

• Positive connection systempromotes a secure fit

• Fast, modular installation

• Color coded for easier topsidelayout

Metal DeckAdapters For use with CP 680-P/M

• Positive connection systempromotes a secure fit to the base

• Fast, modular installation

• Color coded for easieridentification below deck

Water BarrierModule For use with CP 680-P/M

• Available in 2", 3", 4" and 6" sizes

• Adds 1" to the overall height

• Secures to top of device

• A pre-concrete casting waterbarrier solution

• Many tested details meeting UL’sClass I W-Rating

Top Seal Plug For use with 2 inch CP 680-P/M• 1/2" to 2" diameter

pipes

• Restricts water from flowingthrough pipe penetrations

• Easy friction fit around pipes tocreate a water resistant seal

• Forces pipe to be centered in theopening

• A post-concrete casting waterbarrier solution

• Many tested details meeting UL’sClass I W-Rating (pending)

• • • • •

• • • •

• • • • •

• • • • •

• •

• •

CP 681Tub Box KitA unique firestop cast-indevice for recessed tubdrain applications

• Assembles easily with solventcement

• Triangular shape makes workingaround rebar easy

• 3 fastening points instead of 4

• Saves time and labor costs

• Structurally stable during concretepouring

• No special tools required forinstallation

• •

14

14

15

15

16

16

17

Product Information



Chap

ter T

ab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s


Me

tal p

ipe

s

Pla

stic

/gla

ss p

ipe

s

Ca

ble

s/c

ab

le t

rays

Insu

late

d m

eta

l pip

es

Me

tal d

uc

ts

Mu

ltip

le p

en

etr

atio

ns

Join

ts

Application


Closet Stub • Cast-In device for toilet fixtures

• Durable PVC construction (ASTM2665)

• Material can be attached to pipesvia solvent welding or glue

• Economical, dependable solutionfor toilets

Shower andFloor Drain

• Cast-In device for shower/floordrains

• Material can be attached to pipesvia solvent welding or glue

• Economical, dependable solutionfor drains

AeratorAdapterUsed in Combinationwith CP 680-P/M forfirestopping aeratorapplications

• Allows for vertical/horizontal and angle movement

FS-ONE HighPerformanceIntumescent Firestop SealantA water-based intumescentfirestop sealant, designed toexpand when exposed toheat

• UL Listings for various penetratingitems

• Several 1/4" depth systems

• Available in foil pack (600 ml)

• One product to specify, purchaseor inspect for most applications

• Low cost per penetration

• Quick and simple installationprocedure

sodfm,ev iJdjfiwhriuh. NöoWE

Z8Z23awöp3i4eß0288u27�uze

4i5kirdwiloi4jtf-öx-.vbvbvh, ireiv

u9+ß12oeoo

tlke0´9^)&(/R 84tc )v 6453

CP 601SElastomericFirestop SealantA single componentsilicone firestop sealantfor joint and throughpenetration applications

• Silicone based formula

• 1/4" depth systems


• Meets 500 cycle requirements injoint applications (ASTM E 1966 &UL 2079)

• Allows for movement andvibration

• Cost effective solutions

• Fast and easy dispensing

• Smoke, fume and water resistant

• Meets Class 1 W Ratingrequirements

CP 606 Flexible Firestop SealantAn acrylic based firestopsealant for throughpenetration applications

• Acrylic based formula

• Can be painted


• Meets 500 cycle requirements (ASTM E 1966 & UL 2079)

• Fast and easy clean-up with water

• Allows for excellent finishedappearance

• Fast and easy dispensing

•

•

• •

• • • • • •

• • • • •

• • • • •

CP 604Self-LevelingFirestop SealantA self-leveling, single-component, silicone-basedfirestop sealant for use withthrough-penetrations aswell as construction jointsin floors

• 1/4" depth systems

• Excellent elongation/compressionproperties

• Resistant to smoke, fumes andwater



• No tooling required

• Meets Class 1 W Ratingrequirements • • • • •

• Creates a void in concrete thatallows for simple and flexibleinstallation

• Available for 3" and 4" cast-inplace devices

18

19

19

20

21

22

23

Product Information

Chap

ter

Tab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




Me

tal p

ipe

s

Pla

stic

/gla

ss p

ipe

s

Ca

ble

s/c

ab

le t

rays

Insu

late

d m

eta

l pip

es

Me

tal d

uc

ts

Mu

ltip

le p

en

etr

atio

ns

Join

ts

Application


CP 620Fire FoamUniversal firestoppingsolution for commonconstruction materials.Can also be used inconjunction with CP 648EWrap Strip

• One stop application

• Virtually impervious to smoke

• Fully cures in approximately 1minute

• No additional materials required

• High yield

• One solution for various applications• Easy handling for difficult to reach

applications• Excellent mold resistance • Meets Class I W Rating requirements

sodfm,ev iJdjfiwhriuh. NöoWE4i5kirdwiloi4jtf-öx-.vbvbvh, ireiv

u9+ß12oeoo

CP 620 Brandschutzbeschichtung

CP 637Firestop MortarA dry powder, when mixedwith water forms apourable, trowelablefirestop mortar. Can alsobe used in conjunctionwith CP 648E Wrap Strip

• Some applications require minimum 2-1/2" depth

• Cleans up with water

• Economical and simple to use

• Fast and easy clean-up

FS 657 Fire BlockAn innovative and simple to install firestop blockdesigned to expandwhen exposed to heat

• Soft flexible design

• Easy to cut and shape

• User friendly UL systems

• Innovative designs

• Non-curing

• Easy to install, reuse andrepenetrate

• Simply trim block to fit aroundpenetrating items

• Reduces need for extra labor,tools and parts

• Easiest solution for large openingswith multiple penetrations

CP 675TFirestop BoardwithAccessoriesReady to use FirestopBoard designed for largeopenings with cable traysand multiple penetrations

• Lightweight design

• Variety of tested systems

• Systems for one-sided installation

• Easy to install; can be cut withoutpower tools

• Solutions for low and highpenetrated openings

• Solutions for access impededareas

CP 617, CP 617 Land CP 617 XLFirestop Putty PadAn intumescent puttysheet designed to helpprotect electrical outletboxes

• Pad sizes 6" x 7", 7" x 7" or 9" x 9"

• 1 & 2 hour systems

• Tested for wood and steel studs

• Fits most common electricalboxes (refer to UL listings)

• Only one pad to stock and install

• Can be used for commercial andresidential applications

CP 618Firestop Putty StickAn intumescent puttywhich remains pliable overtime

• Non-curing

• No volatile solvents

• Flexible, moldable product

• Reusable and easily repenetrated

• Approved for combustiblepenetrations (cables) along withconduit, EMT and steel pipe

• • • • •

• • • • • •

• • • • •

• • •

• •

CP 658TFirestop PlugA pre-sized, intumescentfirestop plug for blankopenings and cablepenetrations

• Soft Flexible Design

• Versatile in use

• Non-curing

• Fast and cost effective installation

• Provides temporary or permanentfire protection

• Reusable •

* When used with CP 645 or CP 648E Wrap Strip

24

25

26

27

28

29

30

Product Information



Chap

ter T

ab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s


Me

tal p

ipe

s

Pla

stic

/gla

ss p

ipe

s

Ca

ble

s/c

ab

le t

rays

Insu

late

d m

eta

l pip

es

Me

tal d

uc

ts

Mu

ltip

le p

en

etr

atio

ns

Join

ts

Application


CP 643NFirestop CollarA ready-to-use firestopdevice designed tocollapse plastic pipepenetrations whenexposed to fire conditions

• Ready-to-use out of package

• Adjustable mounting tabs

• Low profile design

• Simple and quick installation

• Flexibility in positioning of collar

• Allows for correct installation intight areas

. NöoWE

8u27 uze

bvbvh, ireiv

utzmansch.

CP 644Firestop CollarA ready-to-use firestopdevice designed tocollapse plastic pipepenetrations whenexposed to fire conditions

• Ready-to-use out of package


• Simple and quick installation

• Flexibility in positioning of collar

• Allows for correct installation intight areas



4i5kirdwiloi4jtf-öx-.vbvbvh, ire

iv CP 642 B

randschutzmansch.

CP 648-SFirestop Wrap StripAn intumescent, flexiblefirestop wrap for plasticpipe penetrations

• Pre-measured — no cuttingrequired

• Integrated fastening tape

• No special tools required

CP 648-EFirestop Wrap StripAn intumescent, flexiblefirestop wrap forplastic and insulated pipepenetrations

• May be continuously wrapped

• Flexible

• Versatile

• No need to measure each layer formulti-wrap applications

• Easy to use

• May be used inside the annularspace or outside of the substrate

iwhriuh. NöoWE

4eß0288u27 uze

f-öx-.vbvbvh, ireiv

ndschutzmansch.

CP 672 Speed SprayA flexible fire-rated masticfor construction jointswhere movement up to50% is expected

• Water based formulation

• Maximum flexibility

• Can be used with many “standard”texture spray equipment


• Fast and easy clean-up

• No special modification or extraexpense for product application

Firestop System

CP 777 Speed PlugsPre-cut flute configurationfor top of wall firestopping

CP 767 Speed StripsPre-cut mineral wool stripssuitable for joint applications

• Pre-cut

• Superior finish

• Safe to use

• User friendly

• Leaves no gaps or voids

• Smooth surface provides cost effective spray coverage

• No asbestos

• Inorganic — will not mildew

• Up to 60% faster than castlecutting

• •

•

•

• •

•

•

14-15

• Easy installation

• User friendly

• Saves time and labor costs

31

32

33

34

35

36

Product Information

Chap

ter

Tab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




14

CP 680-P and CP 680-M Technical DataID Footprint Opening Required thru Metal Deck2" 3-3/4" x 4-1/2" 3-1/2" diameter3" 4-3/4" x 5-5/8" 4-1/2" diameter4" 6-3/8" x 6-3/4" 5-1/2" diameter6" 9" x 9-1/2" 7-1/4" diameterExpansion temperature 392°F (200°C)Expansion rate 1:50 (unrestrained)

1:30 (Load expansion, Load = 20g/cm3)Standard Height 8"Temperature resistance Maximum 212°F (100°C)Color CP 680-P: red

CP 680-M: black ApprovalsCalifornia State Fire Marshal Listing No. 4485-1200:135, 4485-1200:136City of New York MEA 1-07-M, MEA 2-07-M Tested in accordance with • UL 1479

• ASTM E 814 • ULC-S115

Internationally tested and approved

FMAPPROVED

F

For use in• Dust and fiber free environments such as hospitals, computer

centers and laboratories

• Concrete floor assemblies rated up to 4 hours

Product Description• A one-step cast-in firestop device for a variety of pipe materials

and diameters

• Helps reduce labor costs and increase productivity

• Ready-to-use out of the package

• Internationally tested and approved by UL and FM

• Reduces the chance of project delays due to failed inspections

Product Features• Quick & simple installation

• SpeedLine Alignment system promotes faster layout

• QuickTurn System creates fast, simple vertical connections

• Integrated moisture and smoke seal

• Innovative adapter for metal deck applications

Installation & Applications• Concrete floors from 2.5" (63 mm) thickness for either flat concrete

or concrete over metal deck

CP 680-M:

- Insulated and non-insulated metal pipes

- EMT and electrical conduits

- Cable bundles

- Multiple pipes

CP 680-P:

Addresses all applications for CP 680-M as well as the following:- Plastic pipes such as PVC, CPVC, ABS, ENT and FRPP

- Fresh and waste water pipes

Not suited for• Areas with high condensation

• Outdoor areas

• Wall applications

CP 680-P and CP 680-M Cast-In Firestop Devices

Notice • Before handling, read Material Safety DataSheet and

product label for safe usage and health information.

• Instructions below are general guidelines — alwaysrefer to the applicable drawing in the UL FireResistance Directory or Hilti Firestop Systems Guidefor complete installation information

Instructions for use• Before pouring concrete, secure the cover cap in

place, thereby preventing the flow of concrete intothe cast-in device.

• Do not use for wall applications.

Concrete floor with metal decking For concrete floor with metal decking applications usethe correct size CP 680 Metal Deck Adapter forinstalled cast-in device and follow the illustrations.

Concrete floor

Installation optionFollow the illustrations if CP 680 has to be cut to slabthickness before installation, or when riser clamps areused.

Installation Instructions

FIRESTOP DEVICEFOR USE IN THROUGH-PENETRATION

FIRESTOP SYSTEMSSEE UL FIRE RESISTANCE DIRECTORY

5N76

CP 680-P over metaldeck

CP 680-P in concrete over wood forms

CP 680-M over metaldeck

CP 680-M in concrete over wood forms

1

1 2

1 2

3 4

5 6

2

3 4

Product Information




15

Chap

ter T

ab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s


Height Extension

Metal Deck Adapters

Product Description• For use when concrete slabs are greater than 8" thick

• Device may add up to 6" with each extension kit

• QuickTurn Connection system promotes a fast, positiveconnection to the top of the appropriate cast-in device

• Red (CP 680-P) and Black (CP 680-M) versions create for easieridentification when both combustible and non-combustiblepenetrants are employed for the same project

Color• CP 680-P Kit — Red cylinder with Red coupling band

• CP 680-M Kit — Black cylinder with Red coupling band

Product Description• For use with concrete over metal deck applications

• 6" cylinder extension protrudes through even the thickest sprayfireproofing

• QuickTurn Connection system promotes a fast, positiveconnection to the underside of the appropriate cast-in device

• Red (CP 680-P) and Black (CP 680-M) versions create for easieridentification when both combustible and non-combustiblepenetrants are employed for the same project

• Opening Required to Place the Cylinder Through a Metal Deck

For 2" Devices — 3-1/2" diameter




Color• CP 680-P Kit — Red cylinder with two (2) metal plates

• CP 680-M Kit — Black cylinder with two (2) metal plates

Notice • Before handling, read Material Safety DataSheet and product

label for safe usage and health information.

• Instructions below are general guidelines — always refer to theapplicable drawing in the UL Fire Resistance Directory or HiltiFirestop Systems Guide for complete installation information





Product Information

Chap

ter

Tab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




16

Water Barrier Module

Top Seal Plug Product Description• A post-installed water barrier solution that impedes water

• Meets W-Rating requirements for select penetrants

• For use where a single penetrant is employed per cast-in device

• Chemically stable elastomeric material will not react withcombustible pipes

Applications• For single penetrants placed through a 2" cast-in place device

• Iron Pipe Sizing (IPS) and Copper Pipe Sizing (CPS) offeringsavailable

• For pipes ranging from nominal 0.5" to 2.0" in diameter

Color• Red

Product Description• A pre-installed water barrier solution that impedes water

• Meets W-Rating requirements for select penetrants

• For use where a single penetrant is employed per cast-in device

• QuickTurn Connection system promotes a fast, positiveconnection to the top of the appropriate cast-in device

Dimension• Adds 1" to all cast-in devices

Pipe Sizes Addressed (See UL Systems)• For 2" Water Module: 2" Pipe

• For 3" Water Module: 2.5" and 3" Pipe

• For 4" Water Module: 4" Pipe

• For 6" Water Module: 6" Pipe

Color• Red housing with black gasket

(Pending)(Pending)









Product Information




17

Chap

ter T

ab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

CP 681 Tub Box Kit



5N76

Technical DataDimensions (LxWxH) 10-3/4" x 13" x slab thicknessApplication dimension Creates a 2-1/2" deep recess in the slabMinimum slab thickness 4-1/2"Intumescent activation Approx. 375°F (190°C)Expansion ratio (unrestricted) 1:10Temperature resistance Maximum 212°F (100°C)Color Red with white PVC legs and couplingStorage Store in dry locationApprovalsCalifornia State Fire Marshall Listing No. 4485-1200:122City of New York MEA 283-06-ETested in accordance with • UL 1479

• ASTM E 814

The Hilti cast-in solutions include an innovative tubbox solution• Structurally stable — stable during concrete pouring

• Assembles easily with solvent cement — no additional toolsrequired

• Triangular shape makes working around rebar easy

• 3 fastening points instead of 4 reduces installation time

• Pre-cut to customer’s height requirement upon request — helpsreduce labor costs

• One system for all pipe materials, easy to choose and inspect

• Accepts a pass through 1-1⁄2" pipe (with a sealing bushing) or astandard 2" P-trap (direct connection to the coupling)

The CP 681 Tub Box Kit includes an ElastomericSealing Bushing• Sealing bushings available for standard schedule 40 pipe or thin

wall piping

• Versatile CP 681 tub box kit allows sealing bushing to be installedfrom top or bottom

Assembly & Installation instructions for CP 681 Tub Box KitNotice • Before handling, read Material Safety DataSheet

and product label for safe usage and healthinformation.


Concrete on wood form 1. Secure the coupling sleeve flange (the larger of the

three flanges) to the floor deck using nails orscrews.

2. Using standard solvent cement on both plasticsurfaces, assemble the CP 681 Tub Box legs andsleeve to bottom of the Tub Box as follows:

• Cement the two 3/4" PVC stabilizing legs to thematching connecting area on the bottom side of theCP 681 Tub Box.

• Cement the CP 681 Tub Box and larger PVC plasticsleeve to the connecting area on the bottom side ofthe CP 681 Tub Box.

• Secure the smaller leg flanges to the deck usingnails or screws.

3. Pour concrete to the proper height. CP 681 Tub Boxassembly is precut to the slab thickness.

4. After concrete is cured, remove the floor deck andfoam insert. Remove pressure test cap beforeinstalling drain piping.

5. Install the tub drain/overflow assembly piping(plastic or brass) through the CP 681 Tub Box andplastic coupling. Insert proper elastomeric bushinginto the bottom or top of the CP 681 Tub Boxassembly around the drain pipe.

Note: Install bushing before final drain/overflowassembly if installing from the top side. Completethe installation by installing branch and trap piping.

1 2 3 4 5

Product Information

Chap

ter

Tab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




18

Closet StubProduct Description• A coupling device designed to address cast-in applications for

toilet fixtures

• Material can be solvent welded to PVC piping

• Available for 3" and 4" PVC applications

Product Dimensions (Diameter x Height)• 3": 5-11/16" x* 3-1/8"

• 4": 6-3/4" x* 3-5/8"

Application Dimensions• 3": 3-1/2" inner diameter (for use with 3" PVC pipe)

• 4": 4-1/2" inner diameter (for use with 4" PVC pipe)

Minimum Slab Thickness• 6"

Color• Red




Hilti Firestop Closet Stubassembly — concrete on woodform for floors• A: Hilti Cast In Firestop Closet Stub

• B: 3" or 4" PVC SCH 40 pipe (supplied by others)

• C*: 3" or 4" Toilet Flange (supplied by others)

1. Secure the Hilti Cast-In Firestop Closet Stub to thefloor deck, using nails or screws. Pre-assemble A &B by solvent welding.

2. Close the top of the assembly to avoid concretefilling (tape or similar).

3. Pour concrete to proper height. After concrete iscured, remove the floor deck and tape.

4. Complete installation by installing Toilet Flange andelbow by solvent welding.


1 2 3 4

Product Information




19

Chap

ter T

ab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

Shower and Floor Drain

Aerator Adapters

Product Description• An economical solution to address shower and floor drain

applications

• The same trusted firestop material as the tub box

• Two variations: (1) extended sleeve & (2) hub coupling

• Designed to accommodate solvent welding to 2" PVC pipes

Product Dimensions• Extended Sleeve: 5-3/4" base diameter 8" height

• Hub Coupling: 5-3/4" base diameter; 2-13/16" height

Application Dimensions• Extended Sleeve: 2-3/8" inner diameter (for use with 2" PVC pipe)

• Hub Coupling: 2-3/8" inner diameter (for use with 2" PVC pipe)

Minimum Slab Thickness• 4-1/2"

Color• Extended Sleeve: red flange with white extended sleeve

• Hub Coupling: red flange with white hub coupling

Aerator-Adapter Technical DataProduct Dimensions (WxLxH) 3": 6" x 6-7/8" x 3"

4": 6" x 8-3/4" x 4-1/2" Application Dimensions (WxLxH) 3": 5-3/4" x 2-3/8"

4": 5-7/8" x 7.5" x 4-1/2" Minimum Slab Thickness 3": 5-1/8"

4": 6-1/2" Color 3": Red

4": RedStorage Store in dry locationTested in Accordance with • UL 1479

• ASTM E 814

Product DescriptionWhen used in conjunction with the appropriate cast-in place device,creates an underside void for the installation of a single stack wastepipe aerator system

Product Features• Up to a 4-1/2" recess created in the slab to reduce final ceiling

height

• Allows for vertical, horizontal and angle movement to simplifyplumbing installations

• Excellent sound insulation

For Use With• Soil and Aerator assemblies




Note: Before purchasing aerator adapters for yourproject, please confirm the following:

• aerators may be employed on the project as perlocal codes and construction allowances

• minimum concrete floor slab thickness

1. Secure the assembly to the floor deck using nails orscrews.

2. Attach the Aerator Adapter to the appropriatecast-in place device.

3. Before pouring concrete, confirm that the cover capof the assembly is properly secured. This willprevent flowing concrete into the CP 680-P/Mduring the concrete pour.

4. Complete installation by installing 3" or 4" cast ironaerator and pipe.

Assembly instructions for Aerator Adapter

1 2 3 4

Product Information

Chap

ter

Tab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s






u9+ß12oeoo

tlke0´9^)&(/R 84tc )v 6453

FS-ONEHigh Performance Intumescent Firestop Sealant

FS-ONE Technical DataChemical basis Water-based intumescent acrylic

dispersionColor RedApplication temperature 40°F to 104°F (5°C to 40°C) Skin forming time Approx. 20-30 min.Curing time Approx. 2 mm / 3 daysMovement capability Approx. 5%Expansion rate Up to 3-5 times (unrestricted): original volumeTemperature resistance (cured) –40°F to 212°F (–40°C to 100°C)Surface burning characteristics Flame Spread: 0(ASTM E 84-96) Smoke Development: 5Sound transmission classification 56 (Relates to specific construction)(ASTM E 90-99) ApprovalsCalifornia State Fire Marshal Listing No. 4485-1200:108City of New York MEA 326-96-M Vol. IVTested in accordance with • UL 1479

• ASTM E 814• ASTM E 84

At 73°F (23°C) and 50% relative humidity

FILL, VOID OR CAVITY MATERIALFOR USE IN THROUGH-PENETRATION


66Y7

FMAPPROVED

F

Product description• Intumescent (expands when exposed to fire) firestop sealant that

helps protect combustible and non-combustible penetrations forup to 4 hours fire rating

Product features• Smoke, gas and water resistant after material has cured

• Contains no halogen, solvents or asbestos

• High fire rating properties

• Water based, easy to clean

• Protects most typical firestop penetration applications

• Can be painted

• Single component systems available

• Meets LEED™ requirements for indoor environmental quality credit4.1 Low Emitting Materials, Sealants and Adhesives and 4.2 Paintsand Coatings

Areas of application• Steel, copper and EMT pipes

• Insulated steel and copper pipes

• Cable bundles

• Closed or vented plastic pipes

• HVAC penetrations

For use with• Concrete, masonry, drywall and wood floor assemblies

• Wall and floor assemblies rated up to 4 hours

Examples• Sealing around plastic pipe penetrations in fire rated construction

• Sealing around combustible and non-combustible penetrations infire rated construction

1. Clean opening. 2. Pack mineral wool.(If required)

3. Apply FS-ONE. 4. Smooth FS-ONE.

5. Leave completedseal undisturbed for 48hours.

6. Fasten identificationplate (if required).

1. Clean opening. 2. Pack mineral wool.(If required)

3. Apply FS-ONE. 4. Smooth FS-ONE.

5. Leave completedseal undisturbed for 48hours.

6. Fastenidentification plate (ifrequired).

Firestop System




Opening 1. Clean the opening. Surfaces to which FS-ONE will be

applied should be cleaned of loose debris, dirt, oil,moisture, frost and wax. Structures supportingpenetrating items must be installed in compliancewith local building and electrical standards.

Application of firestop sealant 2. Install the prescribed backfilling material type and

depth to obtain the desired rating (if required). Leavesufficient depth for applying FS-ONE.

3. Application of firestop sealant: Apply FS-ONE to therequired depth in order to obtain the desired fire rating.Make sure FS-ONE contacts all surfaces to providemaximum adhesion. For application of FS-ONE use astandard caulking gun, foil pack gun, bulk loader andbulk gun. With FS-ONE buckets, Graco type sealantpumps may be used. (Contact pump manufacturer forproper selection).

4. Smoothing of firestop sealant: To complete the seal,tool immediately to give a smooth appearance.Excess sealant, prior to curing, can be cleanedaway from adjacent surfaces and tools with water.

5. Leave completed seal undisturbed for 48 hours.

6. For maintenance reasons, a penetration seal couldbe permanently marked with an identification plate.In such a case, mark the identification plate andfasten it in a visible position next to the seal.

Not for use • High movement expansion joints

• Underwater

• On materials where oil, plasticizers or solvents maybleed i.e. impregnated wood, oil based seals, greenor partially vulcanized rubber

• In any penetration other than those specificallydescribed in this manual or the test reports

Storage • Store only in the original packaging in a location

protected from moisture at temperatures between 40°F (5°C) and 86°F (30°C)

• Observe expiration date on the packaging

Installation instructions for FS-ONE

Firestop System

Firestop System

CA

BLE

PIP

E

Product Information

Hilti, Inc. (U.S.) 1-800-879-8000 • www.us.hilti.com • en español 1-800-879-5000 • Hilti Firestop Systems Guide 2007 21

Chap

ter T

ab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

CP 601SElastomeric Firestop Sealant

CP 601S Technical DataChemical basis Natural Elastic siliconeDensity Approx. 1.25 g/cm3

Color RedApplication temperature 40°F to 104°F (5°C to 40°C)Skin-forming time Approx. 15 min.Curing rate Approx. 2 mm / 3 daysVolume shrinkage Approx. 0 – 5%Movement capability Approx. 25%Temperature resistance –40°F to 320°F (–40°C to 160°C)Surface burning characteristics Flame spread: 0(ASTM E84-96) Smoke development: 30Sound transmission classification 50 (Relates to specific construction)(ASTM E 90-97): ApprovalsCalifornia State Fire Marshal Listing No. 1451-1200:115

Listing No. 1452-1200:113Listing No. 4485-1200:123

City of New York MEA 101-99-M, Vol. IVTested in accordance with • UL 2079 • ASTM E 814

• ASTM E 1966 • ASTM C 920• UL 1479 • ASTM E 84



FIRESTOP SYSTEMS AND JOINT SYSTEMS

SEE UL FIRE RESISTANCE DIRECTORY 66Y7

FMAPPROVED

F

Product description• A silicone based firestop sealant that provides maximum

movement in fire-rated joint applications and pipe penetrations

Product features• Halogen and solvent free

• Asbestos free

• Simple to use and apply

• Good adhesion without use of a primer

• Smoke, fume, water, weather and UV resistant

• Excellent movement capability, meets 500 cycle requirements

(ASTM E 1966 & UL 2079)

• Meets Class I W-rating requirements


Areas of application• Sealing construction/expansion joints

• Top-of-wall joints

• Metal pipes

• Cable bundles


For use with• Various base materials such as masonry, concrete, metal, glass, etc.


Examples• Where a gypsum wall assembly meets the underside of a metal or

concrete deck

• Sealing expansion joints to impede the passage of fire, smoke andtoxic fumes

• Sealing HVAC penetrations through fire-rated assemblies




Opening 1. Clean the opening. Surfaces to which CP 601S will

be applied should be cleaned of loose debris, dirt,oil, wax and grease. The surface should bemoisture and frost free.

Application of firestop 2. Insert fill of mineral wool (or backer as required).

3. Apply firestop over backer.

4. Smooth firestop sealant with a trowel before theskin forms. Once cured, CP 601S can only beremoved mechanically.

5. For maintenance reasons, a penetration seal can bepermanently marked with an identification plate andfastened in a visible position next to the seal.

Chemical resistance • At room temperature the cured silicone sealant is

resistant for a short time to diluted (15%) acids andlyes/alkalis as well as most commercially availablecleaning agents and disinfectants (except thosecontaining iodine).

• Concentrated acids and lyes/alkalis destroy siliconerubber over time.

• Solvents and mineral oils cause cured silicone toswell. Consequently, proper functioning of thesealant should be checked after exposure to asolvent or mineral oil. Please contact your local salesrepresentative or the nearest Hilti center if specialrequirements for chemical resistance have to be met.

Not for use• In areas immersed in water

• Not to be painted


protected from moisture at a temperature of 40°F to77°F (5°C to 25°C)

• Observe expiration date on packaging

Installation instructions for CP 601S

1. Clean opening 2. Insert backingmaterial

3. Apply CP 601S 4. Smooth CP 601S 5. Fasten identificationplate (if required)

1. Clean opening 2. Insert backing

material

3. Apply CP 601S 4. Smooth CP 601S 5. Fasten identificationplate (if required)

Firestop System

Firestop System

JO

INT

DU

CT


Product Information

Chap

ter

Tab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




22

CP 606Flexible Firestop Sealant

CP 606 Technical DataChemical basis Acrylic based firestop sealantColor Available in red, white and grayApplication temperature 40°F to 104°F (5°C to 40°C)Skin-forming time Approx. 15 minCuring time Approx. 3 mm / 3 daysVolume shrinkage Less than 20%Movement capability Approx. 10%Temperature resistance –22°F to 176°F (–30°C to 80°C)Surface burning characteristics Flame Spread: 0(ASTM E 84-96) Smoke Development: 5Sound transmission classification 56 (Relates to specific construction)(ASTM E 90-99) ApprovalsCalifornia State Fire Marshal Listing No. 1452-1200:112

Listing No. 1451-1200:121Listing No. 4485-1200:132

City of New York MEA 100-99-M, Vol. IVTested in accordance with • UL 2079 • ASTM E 814

• ASTM E 1966 • ASTM E 84• UL 1479


FMAPPROVED

F


FIRESTOP SYSTEMS AND JOINT SYSTEMS


Product description• An acrylic based firestop sealant that provides movement

capability in fire rated joints and seals through penetrationsapplications

Product features• Silicone free

• Halogen, asbestos and solvent free

• UV-resistant

• Paintable



• Easy clean up with water

• Single component systems available



• Top-of-wall joints

• Metal pipes

• Cable bundles


For use with• Various base materials such as masonry, concrete, metal, etc.


Examples• Where a gypsum wall assembly meets the underside of

a metal or concrete deck

• Sealing expansion joints to impede the passage of fire, smoke andtoxic fumes

• Sealing around HVAC penetrations through fire-rated assemblies




Opening1. Clean the opening. Surfaces to which CP 606 will


Application of firestop2. Insert fill of mineral wool or backer (as required).


4. Smooth firestop sealant with a trowel before theskin forms. Once cured, CP 606 can only beremoved mechanically.


Not for use• On areas immersed in water

Storage• Store only in the original packaging in a location

protected from moisture at a temperature of 40°F to77°F (5°C to 25°C)

• Observe expiration date on package

Installation instructions for CP 606

1. Clean opening 2. Insert backingmaterial compressedper UL System

3. Apply CP 606 4. Smooth CP 606 5. Fasten identificationplate (if required)

1. Clean opening 2. Insert backingmaterial

3. Apply CP 606 4. Smooth CP 606 5. Fasten identificationplate (if required)

Firestop System

Firestop System

JO

INT

DU

CT

Product Information




23

Chap

ter T

ab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

Product description• Self-leveling, single-component, silicone-based firestop sealant for

use with through-penetrations as well as construction joints infloors.

Product features• Self-leveling–requires no tooling

• Excellent elongation/compression properties

• Resistant to smoke and water


• Smoke, fumes and water resistant

• Meets Class I W-rating requirements



• Metal pipes

• Cable bundles

• Sealing multiple penetrations in small or large openings

For use with• Concrete floors rated up to 3-hours

Examples• Penetrations for metal pipes between floor levels

• Construction joints and expansion joints in floors




Opening 1. Clean the opening. Surfaces to which CP 604 will


Application of firestop 2. Insert fill of mineral wool (or backer as required).


4. Allow firestop sealant to level. Once cured, CP 604can only be removed mechanically.


Chemical resistance • At room temperature the cured silicone sealant is

resistant for a short time to diluted (15%) acids and

lyes/alkalis as well as commercially availablecleaning agents and disinfectants (except thosecontaining iodine).

• Concentrated acids and lyes/alkalis destroy siliconerubber over time.

• Solvents and mineral oils cause cured silicone toswell. Consequently, proper functioning of thesealant should be checked after exposure to asolvent or mineral oil. Please contact your localsales representative or the nearest Hilti Center ifspecial requirements for chemical resistance have tobe met.

Not for use • In areas immersed in water

• Not to be painted


protected from moisture at a temperature of 40°F(5°C) to 77°F (25°C)

• Observe expiration date on packaging

CP 604Self-Leveling Firestop Sealant


FIRESTOP SYSTEMS, JOINT SYSTEMS AND PERIMETER FIRE CONTAINMENT SYSTEMS


FMAPPROVED

F

CP 604 Technical DataChemical basis Neutral elastic siliconeColor GrayApplication temperature 40°F to 104°F (5°C to 40°C)Skin forming time Approx. 15 minCuring time Approx. 2 mm/3 daysJoint movement capability Approx. +20%Temperature resistance –40°F to 248°F (–40°C to 120°C)Surface burning characteristics Flame Spread: 5(ASTM E 84-00) Smoke Development: 60ApprovalsCalifornia State Fire Marshal Listing No. 4485-1200:117

Listing No. 1452-1200:134City of New York MEA 237-02-MTested in accordance with • UL 1479 • ASTM E 1966

• UL 2079 • ASTM E 814• ASTM E 2307 • ASTM E 84



1. Clean opening 2. Insert backing materialcompressed per ULSystem

3. Apply CP 604 4. Self levels — notooling required

5. Fasten identificationplate (if required)

1. Clean opening 2. Insert backing material 3. Apply CP 604 4. Self levels — notooling required

5. Fasten identificationplate (if required)

FirestopSystem

Firestop System

FLO

OR

JO

INT

FLO

OR

Joint installation: For floor applications. Not to be used in walls.

Through Penetration Installation (Top View): For floor applications. Not to be used in walls.

Product Information

Chap

ter

Tab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




24

CP 620Fire FoamProduct description• Innovative firestopping solution for complex applications

Product features• Up to 6 times expansion

• Repenetrable

• Cures within 60 seconds

• Easy handling for difficult to reach applications

• Paintable

• Virtually impervious to smoke

• Mold resistant

• No additional materials required

• Excellent water vapor impermeability


Areas of application• Sealing small to medium size openings

• Cables and cable trays

• Non-combustible pipes

• Combustible pipes when used in conjunction with Hilti Wrap Strips

• Where cables, steel, copper, cast iron or plastic pipes all passthrough the same opening

For use with floor and wall assemblies• Concrete, drywall, masonry

Examples• Multiple penetrations

• Insulated metal pipes




Application1-4.

Prepare dispenser and cartridges as shown below.The Fire Foam from the first few strokes of thedispenser should be discarded until the Fire Foam inthe mixer has a consistent red color.

5. Apply the CP 620 Fire Foam in the opening.

• Begin applying CP 620 Fire Foam at the back ofthe opening and work toward the front. Fill theopening completely with CP 620 Fire Foam.

• When dispensed slowly, the Fire Foam can beeasily built up.

• When dispensed quickly, the consistency of theFire Foam is more liquid allowing it to flow betterbetween the cables. Note: The CP 620 Fire Foambecomes warm for a short time after application.

6. For maintenance reasons, the application can bepermanently marked with an installation plate. Markthe installation plate and fasten it in a visibleposition next to the seal.

Re-installing cables or pipes• Additional cables or pipes can be installed later

without difficulty.

• Use a suitable tool to create an opening(screwdriver, drill bit, etc.). Push the cable or pipethrough and then seal the remaining openingcarefully with CP 620 Fire Foam.

Notes• The CP 620 Fire Foam can be cut back to no less

than the minimum specified installation depth (seeapplicable UL systems for depths).

• Pieces of cured excess CP 620 Fire Foam whichhave been cut off can be laid in the next openingand fresh CP 620 Fire Foam can be applied aroundthese.

Not for use• Exposed to weather

• Exposed to UV

Storage• Store only in the original packaging in a dry place at

a temperature of 40°F to 77°F (5°C to 25°C). Seetechnical data for application and substratetemperatures. Partly-used cartridges can be storedwith mixer attached until they are required again.When re-using a partially used cartridge, simplyattach a new mixer and dispense accordingly.


1. Hold the cartridgein the upright positionand unscrew the cap.

2. Fit the mixer andscrew in a clockwisemotion until secure.

3. Release thedispenser and pullback the piston rod.

4. Insert the cartridgein the dispenser.

5. Apply CP 620 FireFoam, building up a sealby working from theback towards the front.

6. Attach theinstallation plate (if required).

Aus- führungsschild


FIRESTOP SYSTEMS SEE UL FIRE RESISTANCE DIRECTORY

66Y7

FMAPPROVED

F

CP 620 Technical DataChemical basis Two component polyurethaneColor RedFire foam yield Up to 110 in3

Application temperature 32°F to 104°F (0°C to 40°C)Curing time Non-tacky after Approx. 35 seconds

Ready to cut after Approx. 1 minuteThermal insulation (R-value) 2.8–3.0 per inch of thicknessTemperature resistance –22°F to 212°F (–30°C to 100°C)of cured foamSound transmission classification 50 (Relates to specific construction)(ASTM E90-97) Structure-borne sound insulation Pipe/wall 30–50%Surface burning characteristics Flame spread: 0(ASTM E84-01) Smoke development: 15ApprovalsCalifornia State Fire Marshal Listing No. 4485-1200:119City of New York MEA 238-02-MTested in accordance with • UL 1479 • ASTM E 814 • ASTM E 84At 73°F (23°C) and 50% relative humidity

sodfm,ev iJdjfiwhriuh. NöoWE4i5kirdwiloi4jtf-öx-.vbvbvh, ireiv

u9+ß12oeoo

CP 620 Brandschutzbeschichtung

Product Information




25

Chap

ter T

ab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

CP 637Firestop MortarProduct description• Fire-resistant mortar suitable for firestopping large openings

Product features• Quick-setting — forms can be removed in as little as 2 hours

• Superior working properties

• Can be used in horizontal or vertical applications

• Saves time

• Versatile

• Simple mixing

Areas of application• Sealing medium size to large openings with non-combustible

pipes or cable trays

• Permanent fire seal for cables, cable trays and non-combustiblepipes

For use with• Concrete and masonry assemblies

• Walls and floors rated up to 4-hours

Examples• Large openings containing multiple steel,

conduit and EMT pipes

• Large openings with single or multiple cable tray applications




Mix ratio (recommended, mortar to water):

Trowelable 30 lb (14.6 kg) : 2 U.S. gal (8 L)Pourable 30 lb (14.6 kg) : 2.5 U.S. gal (9.5 L)


1. Clean penetration.Pre-moisten sides of penetration.

2. Important! First add clean waterto separate container. Then slowlyadd CP 637 to water while stirringby hand or power mixer to ensuresmooth, lump-free mix. See tableabove for mix ratio.

3. Work prepared mortar intoopening by troweling, pouring, orpumping with suitable pump. Useforms for large openings. Makesure application has been sealedaccording to the applicable UL FireResistance Directory or HiltiFirestop Manual.

4. Fasten identification plate (ifrequired).



66Y7

CP 637 Technical DataColor Light red Application temperature (ideal) 40°F to 110°F(5°C to 43°C)Form removal Approx. 2 hours(depending on consistency)Density: Approx. 40.6 pcf (dry)Expansion on setting 0.08%(approx.)Compressive strength

24 hrs. after casting After full cure • Pourable 508 psi (3.5 N/mm2) 725 psi (5.0 N/mm2) • Plastic 696 psi (4.8 N/mm2) 1200 psi (8.3 N/mm2)• Stiff 870 psi (6.0 N/mm2) 1784 psi (12.3 N/mm2)

Surface burning characteristics Flame spread: 5(ASTM E84-01) Smoke development: 0Yield (30 lb pail) 900–1000 cubic inches depending on mix ratioApprovalsCalifornia State Fire Marshal Listing No. 4485-1200:120City of New York MEA 239-02-MTested in accordance with • ASTM E 814

• UL 1479• ASTM E 84


Product Information

Chap

ter

Tab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




26

FS 657Fire BlockProduct description• Ready-to-use, intumescent flexible block based on a two-

component polyurethane foam

Product features• Suitable for re-penetration or new penetrations

• Economical to use with short installation times

• Easy installation — no special tools required

• Ideal for use in floors — no forming required

• One sided wall systems available

• Halogen, asbestos and solvent free

• Operational immediately after installation

• Can be painted

• Smoke resistant

Areas of application• Sealing single or multiple penetrations in small to large openings

• Temporary or permanent sealing of cables and cable traypenetrations

• Temporary or permanent sealing of insulated and non-insulatedmetallic pipes and combustible pipe penetrations

For use with• Walls (UL tested up to max. opening 52" x 48")

• Floors (UL tested up to max. opening 36" x 36")

• Concrete, porous concrete, masonry and gypsum wall assemblies

• Wall assemblies rated up to 4 hours

• Floor assemblies rated up to 3 hours

Examples• Completely dust and fiber free rooms and places where electrical

installations are frequently used (ie: computer centers, hospitals,laboratories, etc.)

• New buildings in the construction phase and during renovation

• Large openings containing multiple penetrations as found inproduction bays, warehouses, hospitals etc.

Installation instructions for FS 657

FS 657 Technical DataColor RedApplication temperature 40° F to 104° F (5° C to 40° C)Temperature resistance 5° F to 140° F(-15° C to 60° C)Intumescent Activation Approx. 572°F (300°C)Expansion ratio (unrestricted) Up to 1:3Surface burning characteristics Flame Spread Index: 0(ASTM E 84-96) Smoke Development Index: 25Sound transmission classification 54 (Relates to specific construction)(ASTM E 90-99) ApprovalsCalifornia State Fire Marshal Listing No. 4485-1200:106City of New York MEA 325-96-MTested in accordance with • UL 1479





66Y7

FMAPPROVED

F




Opening1. Clean the opening. Penetration and penetration

supporting structures must be installed incompliance with local building and electricalstandards.

Application of Fire Blocks2a.If no penetrations are located, build up FS 657 FIRE

BLOCK firmly seated, within opening.

2b.If penetrations are located, build up FS 657 FIREBLOCK firmly seated, while cutting blocks with aknife to suit the placed penetrations.

3. Finish building up FIRE BLOCKS until entire openingis filled.

4. Completely fill cable spaces, gaps between blocksand pipes, and joints with FS-ONE Firestop Sealant.


Re-installing cables or otherpenetrations• Remove or cut the block from the seal.

• Install the penetrant and re-lay the block incompliance with the approval. Fill gaps and spaceswith FS-ONE.

Single cables can be run through joints betweenblocks or a hole can be drilled through a block usinga sharpened piece of metal pipe or tubing.

Not for use• In wet rooms, outdoors or exposed to the weather

or UV radiation (can be done only after applying anadditional silicone coating, i.e. CP 601S).


protected from moisture and direct sunlight

1. Clean opening. 2a. Build up blocks 2b. Cut blocks to sizefor penetrations inplace

3. Build up blocks 4. Fill gaps with

FS-ONE, CP 617 orCP 618 putty.

5. Fasten identificationplate in place (Ifrequired)

Product Information




27

Chap

ter T

ab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

CP 675TFirestop Board with AccessoriesProduct description• Ready to use Firestop Board designed for large openings with

cable trays and multiple penetrations

Product features• Lightweight design

• Satisfies a wide range of application scenarios

• Allows for high flexibility and eases re-penetration / cable miningfrom one side of the wall

• Easy and fast cable re-penetration and cable mining with reducedlabor and materials

• Labor saving “one person, one sided installation” method

• Polyurethane foam material, easy to cut without electric tools

• No dust, no fibers, no mess

• Same system for all types of wall materials

Areas of application• Temporary or permanent sealing of cables and cable tray

penetrations

• Sealing single or multiple penetrations in large openings

• Temporary or permanent sealing of large blank openings

For use with• Concrete, concrete block, and gypsum wall assemblies

• Concrete floor assemblies

Examples• Locations where telecommunications and electrical applications

are modified on a regular basis such as central office facilities,computer data centers, commercial buildings, healthcare facilities,and laboratories

• New buildings under construction and during renovation

CP 675T Technical DataColor RedSize 26" x 39" x 1" (Large Board)

(660 mm x 990 mm x 25 mm)26" x 28" x 1" (Small Board)(660 mm x 711 mm x 25 mm)

Density 320 kg/m3

Application temperature -22°F to 176°F (-30°C to 80°C)Temperature resistance -22°F to 176°F (-30°C to 80°C)Surface burning characteristics Flame Spread Index: 5(ASTM E 84-00) Smoke Development Index: 10ApprovalsCalifornia State Fire Marshall Listing No. 4485-1200:125City of New York MEA 283-04-MTested in accordance with • UL 1479


Installation Instructions for CP 675T Firestop BoardNotice • Before handling, read Material Safety DataSheet and



Surface Mounted Installation (wall)1. Clean the opening.

2. Measure the size of the opening. Cut the FirestopBoard to size (check system for overlaprequirements) with a utility knife, hand saw, circularsaw, jig saw, or table saw.

3. If penetrants run through the opening, cut theFirestop Board correspondingly (max. annular spacebetween Board and penetrant: 1/2"). The Board canbe cut into two pieces or just cut to allow space forthe penetrant(s).

4. Apply CP 619T Putty Roll around edges of theFirestop Board next to the wall. In case ofpenetrants, the cables and cable trays have to besealed with CP 619T Putty Roll at their interfacewith the Firestop Board.

5. Attach Firestop Board with approved Hilti anchorsas specified in accordance with the applicablefirestop system. When two Firestop Boards cometogether, seal intersection with CP 619T Putty Rollor FS-ONE (per firestop system requirements).

6. Fasten identification plate (if required).

7. Repeat steps on other side of wall.

Frame Mounted Installation (wall)1. Clean the opening.

2. Measure the size of the opening. Cut the CP 675TZ-Frame component to size and attach to top andboth sides of opening as specified by firestopsystem with appropriate Hilti fasteners. Apply CP619T Putty Roll to back lip of Z-Frame insideopening.

3. Apply a maximum of three rows (6") of FS657 FireBlocks in the opening above and below cable tray(lengthwise). Cut the CP 675T T-Separator Bar tothe width of the opening and put it on top of the FS657 Fire Blocks (T-edge against back of opening).Apply CP 619T Putty Roll to the backward T-Baredge protruding above the FS 657 Fire Blocksection and around back lip of frames.

4. Cut Firestop Boards to size +1/2" vertically. Use theextra 1/2” to compress the FS 657 Fire Blockpartition and provide a tight fit into the opening.Place CP 675T Distance Holders around FirestopBoard at a maximum of every 8". With downwardpressure, press top of inside Firestop Board intoopening and push flush with back edge of Z-Framefollowed by outside Firestop Board inserted flushwith wall surface.

5. Secure front of Firestop Board with Z-FrameLatches every 8". Apply CP 619T Putty Roll over theintersection between the Board and the Frame. Fillvoids around penetrating items within FS 657 FireBlock partition with Hilti Firestop Putty. Refer to ULsystems for complete details.

6. Fasten identification plate (if required).

Not for use• In wet rooms, outdoors or in areas exposed to the

weather or UV radiation.





5N76

FMAPPROVED

F

Product Information

Chap

ter

Tab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




28

CP 617, CP 617L & CP 617XLFirestop Putty PadProduct description• A moldable firestop putty designed to help protect electrical outlet

boxes

Product features• Applied by hand

• Fast installation

Areas of application• Protection of electrical outlet boxes

For use with• Gypsum wall assemblies with wood or metal studs

Examples• Where two outlets are within a single stud/cavity or within 24"

(not back to back)


CP 617 Technical DataDimensions CP 617: 6" x 7" x 1/8"(15 x 18 x 0.3 cm)

CP 617L: 7" x 7" x 1/8" (18 x 18 x 0.3 cm)CP 617XL: 9" x 9" x 1/8" (23 x 23 x 0.3 cm)

Consistency Moldable puttyColor RedApplication temperature 40°F (5°C) to 95°F (35°C)Storage temperature 40°F (5°C) to 104°F (40°C)Cure Non-curingDensity 1.48 g/cm3

Intumescent activation Approx. 220°F to 250°F (104°C to 121°C)Volatile solvents NoneAsbestos fibers NoneSurface burning characteristics Flame Spread: 5(ASTM E 84-96) Smoke development: 5Sound transmission classification 55 (Relates to specific construction)(ASTM E 90-97) ApprovalsCalifornia State Fire Marshal Listing No. 4485-1200:129City of New York MEA-102-99-MTested in accordance with • UL 263

• ASTM E 84At 73°F (23°C) and 50% relative humidity

FMAPPROVED

F

WALL OPENING PROTECTIVE MATERIAL FIRE RESISTANCE CLASSIFICATION

SEE PRODUCT CATEGORY IN UL FIRE RESISTANCE DIRECTORY

66Y7




Application of firestop putty1. Remove label from one side of pad. For a 1 to 2

hour fire rating, one CP 617 pad is required.Exposed side of pad is placed against box.

2. Adhere pad to side of the box, overlapping the studand all edges of the box. When drywall is installed:fix pad into gap between electrical box and gypsumboard slightly overlapping the inner wall boardsurface. When drywall will be installed later: overlapfront edge of electrical box so that CP 617 will becompressed around edges of box as gypsum boardis installed.

3. Reshape CP 617 to fit around conduit or cables.

4. Press CP 617 to all sides of electrical box. Trimexcess at corners and apply to conduit fittingsconnected to the box.

5. Remove other side of label. To help prevent passageof cold smoke, CP 617 may optionally be placedinto inside of electrical conduit fittings.

Not for use• In areas exposed to water

Storage• Store only in the original packaging in a location at

temperatures 40°F (5°C) to 104°F (40°C)

1. Remove label from oneside of CP 617

2. Adhere CP 617 toapplication

3. Reshape CP 617 to fitaround box

4. Press CP 617 to allsides of application

5. Remove other side oflabel

Product Information




29

Chap

ter T

ab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

CP 618 Firestop Putty StickProduct description• An intumescent, non-hardening, firestop putty for cable and pipe

penetrations

Product features• Contains no volatile solvents or asbestos

• Easy to re-penetrate

Areas of application• Single or bundled cables

• Non-combustible pipe

• Blank openings

• Reusable

• Easy to add or subtract cables

• Fast installation

For use with• Concrete, masonry and gypsum wall assemblies


Examples• Where telecommunication and data lines penetrate gypsum wall

assemblies

• Where steel conduit and EMT penetrate concrete and block wallassemblies

• Where blank openings exist in concrete and block wall assemblies


CP 618 Technical DataDimensions 18 in3

Consistency Moldable puttyColor RedApplication temperature 40°F to 95°F (5°C to 35°C)Cure Non-curingDensity Approx. 1.48 g/cm3

Intumescent activation Approx. 220°F to 250°F (104°C to 121°C)Surface burning characteristics Flame Spread: 5(ASTM E84-96) Smoke development: 5Sound transmission classification 49 (Relates to specific construction)(ASTM E 90-97) ApprovalsCalifornia State Fire Marshal Listing No. 4485-1200:111City of New York MEA-98-99-MTested in accordance with • UL 1479






Opening1. Clean the opening: Surfaces to which CP 618 will

be applied should be cleaned of loose debris, dirt,oil, moisture, frost and wax.

Application of firestop putty

2. Install the prescribed backing material, if required.

3. Install CP 618 Firestop Putty to the required depth,making sure that the putty contacts all surfaces toprovide the greatest adhesion.

4. Smooth CP 618 putty.


6. Re-installation (not shown): Remove and re-install CP 618 Firestop Putty as needed.

Not for use• In areas exposed to water

Storage• Store only in the original packaging at temperatures

40°F to 104°F (5°C to 40°C)



66Y7

FMAPPROVED

F

1. Clean opening 2. Slice CP 618 to bepacked into opening fromstick (optional sleeve)

3. Pack in CP 618 4. Smooth CP 618 5. Fasten installation plate(if required)

Product Information

Chap

ter

Tab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




30

CP 658TFirestop PlugProduct description• Ready-to-use intumescent flexible plug based on a two

component polyurethane foam

Product features• Fast and easy installation — no special tools required, helps

reduce installation time and costs

• Immediately functional after installation

• Suitable for laying new cables later

• Versatile in use (temporary or permanent protection)

• Smoke resistant

• Virtually dust and fiber free

• Halogen and solvent free

• Can be painted

Areas of application• Walls and floors

• Temporary or permanent sealing of cables — single or bundledcables

Examples• Dust and fiber free rooms and places where electrical installations

are frequently changed such as computer centers, hospitals andlaboratories

• New buildings in the construction phase and during renovation

• Office buildings, production bays, warehouses

Installation instructions for CP 658TNotice • Before handling, read Material Safety DataSheet and



Opening1. Clean the opening. surfaces CP 658T will be in

contact with, should be cleaned of loose debris,dirt, oil, moisture, frost and wax.

Application of firestop plug2a. If there are no penetrations, install CP 658T within

opening and bead with Hilti CP 618 Putty Stickwhere firestop plug interfaces with inside of sleeve(when required).

2b. If there are penetrations, cut CP 658T to fit aroundcables. Insert firestop plug into sleeve. Optional:seal cables by forcing CP 618 into interstices ofcables.

Re-installing cables• Remove firestop plug from opening

• Install the penetrant and re-install the firestop plugin compliance with the appropriate UL system.

• If single cables are installed, a hole can be drilledthrough the firestop plug and a cable passedthrough.

Not for use• In wet rooms or outdoors exposed to the weather or

UV radiation



CP 658T Technical DataDensity Approx. 0.25 g/cm3

Color RedApplication temperature 40°F to 104°F (5°C to 40°C)Temperature resistance 5°F to 140°F (-15°C to 60°C)Intumescent activation Approx. 572°F (300°C)Expansion ratio (unrestricted) Approx. 1:3ApprovalsCalifornia State Fire Marshal Listing No: 4485-1200:130City of New York MEA 48-04-M Surface burning characteristics Flame Spread Index:0(ASTM E 84-96) Smoke Development Index: 25 Tested in accordance with • UL 1479


(At 73°F (23°C) and 50% relative humidity)

FMAPPROVED

F

FILL, VOID OR CAVITY MATERIALSFOR USE IN THROUGH-PENETRATION


66Y7

Aus-führungsschild

1. Clean opening 2. Blank opening: Installplug (sleeved opening)and CP618 Putty Stick

3. With cables: Cut plug tofit around cables

4. Install plug aroundcables (optional: CP618Putty Stick forced intointerstices of cables)

5. Fasten installation platein place (if required)

Product Information




31

Chap

ter T

ab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

CP 643N Firestop CollarProduct description• A ready-to-use firestop collar, made of a galvanized steel housing

and intumescent inserts for firestopping combustible pipes

Product features• Ready-to-use collar

• No construction required

• Fast installation time


• Low profile for tight installations

Areas of application• Firestopping combustible pipes up to 6" diameter in penetrations

through fire walls and floors

• Suitable for the following pipe materials:

PVC, CPVC, ABS, PVDF, PP and FRPP

For use with• Concrete, masonry, wood floor and gypsum wall assemblies


Types of installation• Wall: two collars, one on each side

• Floor: one collar on underside (bottom)

Example• Waste water pipes

• Fresh water pipes

Installation instructions for CP 643N


Z8Z23awöp3i4eß0288u27 uze


u9+ß12oeoo

CP 643 Brandschutzmansch.




Opening1. Clean the plastic pipes. Expansion of the

intumescent material during a fire acts to close theplastic pipe. Very dirty pipes (ie: with remains ofmortar) may lead to a delay in this closing action.Soiled plastic pipes should, therefore, be cleaned inthe area where the CP 643N firestop collar is to beinstalled.

Application of firestop system2. Seal the opening if required. Gaps may be closed

with FS-ONE. The approved methods vary and aregiven in the specific UL system.

3. Close the CP 643N firestop collar. Place the CP 643N firestop collar around the plastic pipe andlock the closure by applying firm pressure until itlatches.

4. Attach fastening hooks. The fastening hooks can beattached to various points on the metal housing.This allows the fastening points to be made to suitthe space available in each case. The hooks mustbe positioned as symmetrically as possible. Therequired number of fastening hooks is indicated onthe packaging.

5. Fastening the CP 643N firestop collar. Only whenfastened properly can CP 643N offer protectionagainst fire.

a. Mark the fastening points.

b. Drill holes with a Hilti rotary hammer drill (i.e. TE 5)or, depending on base material, fasten using Hiltipowder-actuated tool.

c. To secure the CP 643N firestop collar, use Hiltianchors/fasteners.

d. For maintenance reasons, a penetration can bepermanently marked with an identification plate andfastened in a visible position next to the seal.

Not for use• With metal pipes

• In highly corrosive surroundings

• With unapproved anchors/fasteners


protected from moisture

1. Clean plastic pipe. 2. Close remaining gap toprovide smoke and gasresistant seal.

3. Close collar. 4. Attach fastening hooks. 5. Fasten collar andidentification plate (if required).

Firestop System

FMAPPROVED

F



5N76

CP 643N Technical DataPipe Collar Collar No. of

outside outside Height hooks& Description dia (in.) dia. (in.) (in.) fastenersCP 643-50/1.5"N 1.4–2.0 2.8 0.9 2CP 643-63/2"N 2.0–2.5 3.4 1.3 2CP 643-90/3"N 2.6–3.6 4.9 1.7 3CP 643-110/4"N 3.6–4.5 6.0 1.9 3CP 643-160/6"N 6.6 9.8 1.9 4Temperature resistance -40°F to 140°F (–40°C to 60°C)Intumescent Activation Approx. 392°F (200°C)Expansion ratio (unrestricted) Up to 1:10ApprovalsCalifornia State Fire Marshal Listing No. 4485-1200:113City of New York MEA 630-06-MTested in accordance with • UL 1479

• ASTM E 814

Product Information

Chap

ter

Tab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




32

CP 644Firestop CollarProduct description• A ready-to-use firestop collar, made of galvanized steel housing

and intumescent inserts for firestopping large combustible pipes

Product features• Ready-to-use collar

• No construction required

• Fast installation time

• Adjustable/moveable fastening tabs

Areas of application• Sealing of penetrations for combustible pipes from 8" to 10"

in diameter

• Vented or closed pipe

• PVC or CPVC pipe

For use with• Concrete, masonry, and gypsum walls


Types of installation• Wall: two collars, one on each side

• Floor: one collar on underside (bottom)

Examples• Waste water pipes



CP 644 Technical DataPipe Collar Collar No. of

outside outside Height hooks& Description dia (in.) dia. (in.) (in.) fastenersCP 644-200/8" 8.8 10.0 6.9 10CP 644-250/10" 10.8 12.4 9.1 12ApprovalsCalifornia State Fire Marshal Listing No: 1185-1200:128City of New York MEA 631-06-MTested in accordance with • UL 1479

• ASTM E 814



4i5kirdwiloi4jtf-öx-.vbvbvh, ire

iv

u9+ß12oeoo





Opening1. Clean the plastic pipes. Expansion of the

intumescent material during a fire acts to close theplastic pipe. Very dirty pipes, (ie: with remains ofmortar) may lead to a delay in this closing action.Soiled plastic pipes should, therefore, be cleaned inthe area where the CP 644 firestop collar is to beinstalled.

Application of firestop system2. Seal the opening. Gaps must be closed with FS-

ONE. The approved methods vary and are given inthe specific UL system.

3. Close the CP 644 firestop collar. Place the CP 644firestop collar around the plastic pipe and lock theclosure by applying firm pressure until it latches.

4. Attach fastening hooks. The fastening hooks can beattached to various points on the metal housing.This allows the fastening points to be made to suitthe space available in each case.

The hooks must be positioned as symmetrically aspossible. The required number of fastening hooks isindicated on the packaging.

5. Fastening the CP 644 firestop collar. Only whenfastened properly can CP 644 offer protectionagainst fire passing through.

a. Mark the fastening points.

b. Drill holes with a Hilti rotary hammer drill (i.e. TE 5) or, depending on base material, fastenusing Hilti powder-actuated tool.

c. To secure the CP 644 firestop collar, use Hiltianchors/fasteners.

d. For maintenance reasons, a penetration can bepermanently marked with an identification plateand fastened in a visible position next to the seal.

Not for use• With metal pipes

• In highly corrosive surroundings

• With unapproved anchors/fasteners


protected from moisture



5N76

1. Clean plastic pipe 2. Close remaining gap toprovide smoke and gasresistant seal

3. Close collar 4. Attach fastening hooks 5. Fasten collar andidentification plate. (Ifrequired)

Firestop System

Product Information




33

Chap

ter T

ab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

CP 648-SFirestop Wrap StripProduct description• A single wrap strip of intumescent, flexible firestop for use with

plastic and insulated pipe penetrations

Product features• Highly Intumescent

• Pre-measured — no cutting required

• Integrated fastening tape

• Cost effective

• Quick and easy closure without tools

• Ideal for very tight installations

Areas of application• Firestopping combustible pipe penetrations

• Difficult applications where space is limited

• Penetrations through concrete over metal deck

• Suitable for the following plastic pipe materials: PVC, CPVC, ABS, FRPP





• Decking penetrations

Installation instructions for CP 648-S

CP 648-S Technical DataDensity Approx. 1.35 g/cm3

Approx. Dimens. 1.5" : 3/16" x 1" x 6-3/4" (thkns" x width" x length") 2" : 3/16" x 1" x 8-1/4"

3" : 3/16" x 1-3/4" x 11-1/2" 4" : 3/8" x 1-3/4" x 15" 6" : 1/2" x 1-3/4" x 22-1/4"

Color Black with foil backingTemperature resistance –40°F to 212°F (–40°C to 100°C)Intumescent activation Approx. 320°F (160°C)Expansion ratio (unrestricted) 1:40Surface burning characteristics Flame Spread Index: In progress(ASTM E 84-96) Smoke Development Index: In progressApprovalsCalifornia State Fire Marshal Listing No: 4485-1200:127Tested in accordance with • UL 1479





66Y7

FMAPPROVED

F




Installation1. Clean the plastic or insulated pipe penetration.

Expansion of the intumescent material during a firecloses the plastic pipe. Very dirty pipes (ie: withremains of mortar) may lead to a delay in the closingaction. Soiled plastic or insulated pipes should,therefore, be cleaned in the area where the CP 648-S Firestop Wrap Strip is to be installed.

2. Install Wrap Strip. First check the annular space toensure compatibility with the appropriate ULSystem. Use the CP 648-S Firestop Wrap Stripcorresponding to the diameter of the pipe to beinstalled. Wrap the CP 648-S strip around the pipeand fasten it tightly using the integrated adhesivestrip.

Push the CP 648-S Firestop Wrap Strip into theannular space in accordance with the UL listing.

3. Seal against smoke and gas. Seal the remaining gapwith Hilti FS-ONE sealant.


Not for use• In highly corrosive surroundings

• In outdoor areas


protected from moisture at temperatures between 23°F and 86°F (–5°C and 30°C).

1. Clean penetration 2A. Wrap the CP 648-SWrap Strip aroundthe pipe and fasten ittightly with the adhesive strip.

2B. Push the CP 648-SWrap Strip along the pipeand into the annular spaceas indicated above.

3. Seal penetration againstsmoke with FS-ONEsealant.

4. Fasten installation plate(If required)

Firestop System

Product Information

Chap

ter

Tab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




34

CP 648-EFirestop Wrap StripProduct description• An intumescent, flexible firestop wrap strip for plastic and

insulated pipe penetrations

Product features• Highly Intumescent

• Long length avoids waste

• Can be continuously wrapped

• Cost effective

• Quick and easy closure without tools

• Ideal for very tight installations

Areas of application• Firestopping combustible pipe penetrations

• Difficult applications where space is limited

• Penetrations through concrete over metal deck

• Plastic and insulated penetrations using PVC, CPVC, ABS, FRPP and PEX





• Decking penetrations

Installation instructions for CP 648-E


Z8Z23awöp3i4eß0288u27 uze


u9+ß12oeoo





Opening1. Clean the plastic or insulated pipe penetration.

Expansion of the intumescent material during a firecloses the plastic or insulated pipe penetration. Verydirty pipes (ie: with remains of mortar) may lead to adelay in this closing action. Soiled plastic pipes orinsulated pipe penetrations should, therefore, becleaned in the area where the CP 648-E FirestopWrap Strip is to be installed.

Application of firestop system2. Tightly wrap the required number of strips

continuously around the penetrant, and hold inplace with tape.

3. Push the Hilti Wrap Strip into the opening until it isflush with the substrate surface unless otherwiserequired by the UL system. It may be required bythe UL system to clamp, wire or use a Hilti RetainingCollar to secure the wrap strip in place for someapplications.

4. If the UL system requires a cold smoke seal, thenapply the proper amount of Hilti FS-ONE sealant inthe opening over the wrap strip.


Not for use• In highly corrosive surroundings

• With unapproved retaining collars, anchors/fasteners

• Outdoors


protected from moisture at temperatures between 23°F and 86°F (–5°C and 30°C).

CP 648-E Technical DataDensity Approx. 1.35 g/cm3

Dimensions (Approximate) 3/16" x 1" x 33 ft or 3/16" x 1-3/4" x 33 ftColor Black with foil backingTemperature resistance –40°F to 212°F (–40°C to 100°C)Intumescent activation Approx. 320°F (160°C)Expansion ratio (unrestricted) 1:40Surface burning characteristics Flame Spread Index: In progress(ASTM E 84-96) Smoke Development Index: In progressApprovalsCalifornia State Fire Marshal Listing No: 4485-1200:126Tested in accordance with • UL 1479





66Y7

FMAPPROVED

F

1. Clean penetration 2. Wrap strips around pipethe specified number oftimes

3. Push Wrap Strips intohole

4. Seal penetration againstsmoke with FS-ONE

5. Fasten installation plate(If required)

Firestop System

Product Information




35

Chap

ter T

ab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

CP 672 Speed SprayProduct description• A sprayable fire-rated mastic for construction joints where

maximum movement is required

Product features• Sprayable or apply by brush

• Maximum flexibility, meets 500 cycle requirements (Class II & IIIApproval) (ASTM E 1966 & UL 2079)

• Quick and easy installation with the Spray Tech EPX 2355 or 2555Sprayers can save you time and money

• CP 672 Speed Spray contains no halogens, solvents or asbestosso it is safe to use and won’t harm the environment

• Water based formulation so spills and over-spray clean up quicklyand easily

• Paintable


Areas of application• Top-of-wall joints

• Curtain wall / edge of slab

• Expansion joints

For use with• Concrete, masonry and gypsum wall assemblies

• Wall and floor / wall assemblies rated up to 4 hours

Examples• Where a gypsum wall assembly meets the underside of a metal or

concrete deck

• Where a concrete floor assembly meets with non-rated exteriorwall (concrete, glass, etc.)

• Where two concrete floor/wall assemblies meet


Firestop System

CP 672 Technical DataDensity Approx. 9 lb/gal (1.25 g/cm3)Color Available in red and whiteApplication temperature 40°F to 104°F (5°C to 40°C)Temperature resistance -40°F to 176°F (-40°C to 80°C)Consistency Sprayable liquidChemical basis Latex based dispersionWorking time 30–45 minutesCure time Approx. 48 hours @ 73°F, 50% humidityPh-value Approx. 8.0Movement capability Up to 50%Surface burning characteristics Flame spread: 10(ASTM E 84-06) Smoke development: 10Sound transmission classification 55 (Related to specific construction)(ASTM E 90-99) ApprovalsCalifornia State Fire Marshal Listing No. 1451-1200:114

Listing No. 1452-1200:109City of New York MEA 99-99-M

MEA 132-01-MTested in accordance with • UL 2079

• ASTM E 1966• ASTM E 84• ASTM E 2307


FILL, VOID OR CAVITY MATERIALFOR USE IN JOINT SYSTEMS AND

PERIMETER FIRE CONTAINMENT SYSTEMSSEE UL FIRE RESISTANCE DIRECTORY

66Y7

FMAPPROVED

F




Opening1. Clean the opening. Surfaces to which CP 672 will

be applied should be cleaned of loose debris, dirt,oil, wax and grease. The surface should be moistureand frost free.

Application of firestop spray2. Mineral wool packing: Install the prescribed back

filling material type and depth to obtain desiredrating.

3. Application of firestop spray: Apply CP 672 to therequired depth in order to obtain the desired rating.Make sure CP 672 contacts all surfaces andoverlaps beyond all surrounding surfaces (Refer toUL System). Spray Tech Sprayers have beensuccessful in applying CP 672 Firestop Joint Spray.Hilti recommends the use of the Spray Tech EPX 2355 (for application temperatures above 50°F)or EPX 2555 Sprayers. CP 672 may also be brushedon with a paint brush. Contact Hilti TechnicalSupport for more information.

4. Curing time: Allow 48 hours (at 73°F / 23°C) for the CP 672 to fully cure.

5. Identification: For maintenance reasons all CP 672applications can be permanently marked with anidentification plate and fastened in a visible positionnext to the seal.

Not for use• In areas underwater

• On hot surfaces (above 176°F)

Storage• Store only in the original packaging at temperatures

40°F to 77°F (5°C to 37°C)

• Observe expiration date on package

1. Clean opening 2. Pack in mineral woolcompressed per ULSystem

3. Spray or brush on CP 672

4. Allow CP 672 to cure 5. Fasten identification plate(if required)

Firestop System

Product Information

Chap

ter

Tab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




36

CP 767 Speed Strips

CP 777 Speed Plugs

CP 767 and CP 777 Technical DataTested in accordance with • UL 2079

• ASTM E 1966• ASTM C G12 Type I-IUB

Firestop System

Product description• CP 777: Pre-formed mineral wool plugs for 1.5", 2" and 3" decks

• CP 767: Pre-formed mineral wool strips suitable for jointapplications

Product features• Pre-cut to industry standard size decking flutes

• Reduces material waste

• 3 sizes available

• Pre-cut — leaves no gaps or voids

• Smooth surface provides cost effective spray coverage

• Safe to use — no asbestos / inorganic, will not mildew

• Up to 60% faster than castle cutting!

Areas of application• Top-of-wall

Tested and approved• UL Classified when used in conjunction with CP 606 Flexible

Firestop Sealant, CP 601S Elastomeric Firestop Sealant or CP 672Speed Spray

FORMING MATERIAL FOR USE IN JOINT SYSTEMS

SEE UL FIRE RESISTANCE DIRECTORY17RL

Castle Cutting

Conventional Mineral Wool

Hilti Speed Plugs

50 MINUTES

35 MINUTES

20 MINUTES

60% Faster than Castle Cutting

43% Faster than Conventional Mineral Wool*Based upon 40 linear feet of installation

Saves Time and Money!

Easy One step installation...Simply cut to lengthand install.

Full Coverage Pre-cut flute configuration leaves no gaps or voids.

Superior Finish Smooth surface allows quick andcost effective coverage with Hilti CP 672 SpeedSpray.

Easy Utilize Speed Strips in joints between wallsubstrate and bottom of deck. Compress per ULSystem.

Installation instructions for CP 777 Speed Plugs





FACT Program




37

Chap

ter T

ab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

The facts are clear, when itcomes to building coderequirements, a BalancedFire Protection System isimperative. And when itcomes to getting it right,Hilti provides experience,expertise and innovation.

The Hilti Facility AssuranceContainment Team (FACT) Programoffers step-by-step fire containmentconsultation and training including:

FS 411 — Palm OS based firestopselection software with project managerfor selection and tracking UL systemsand their locations within yourfacility

On-Site Training —Step-by-step trainingfor contractors andin-house personnelto help safeguardyour facility throughpassive fireprotection

BASIC Training —A set of videoscovering the basics offire containment includingBarrier, Application,Selection, Installation andConfirmation

BASIC Firestop Training Examination& Certification — Available online atwww.hiltibasicexam.com

Firestop Installation PermitProgram — The Hilti FIPP is acomprehensive program including a setof operating procedures, the mostcommon UL systems used in building

construction, MSDS,product technical data,Contractor FirestopPermit, Letter ofConformance, online

assistance tutorial and afrequently asked questions

section

Hilti Accredited Firestop SpecialtyContractors — Access to a nationwidenetwork of independent professionalfirestop installers who have receivedspecialized training by Hilti

System Labeling — Hilti firestopidentification labels and plates for proper

identification of installed ULsystems

Engineers — A team ofdegreed Fire

Protection Engineerswho provideprofessionalconsultation andEngineeringJudgments for

complex and uniqueapplications

EnvironmentalSolutions — A range of

“clean machine” toolsdesigned to minimize noise levels

and the impact of construction activitieson building occupants with integrateddust removal and recycling systems

Loyalty Program — Project-basedpricing for all contractors working at orwithin a facility, including online orderingwith no shipping charges, rebatesprograms and tool placementagreements

CONTAINMENT

SUPPRESSIONDETECTION

Item No. Qty Description

3001978 1 FACT Program ¿Includes BASIC Training, FS 411 software and FIPP

3001980 1 FS 411 Firestop System Selector Software ¡For use only on Palm PDAs and other devices running Palm operating systems

3410992 1 BASIC Training ¬

Hilti FACT Program

To order your FACT Program, call 1-800-879-8000

¿

¡

¬

Ordering Information

Chap

ter

Tab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




38

CP 680-P Cast-In Device for Combustible Penetrations (red)Item No. Qty Description

244244 1 CP 680-P 2"

244245 1 CP 680-P 3"

244246 1 CP 680-P 4"

244247 1 CP 680-P 6"

CP 680-M Cast-In Device for Metallic Penetrations (black)Item No. Qty Description

244248 1 CP 680-M 2"

244249 1 CP 680-M 3"

244250 1 CP 680-M 4"

244251 1 CP 680-M 6"

Water Barrier Module (for use with CP 680-P/M) ¡Item No. Qty Description

244260 10 CP 680-P/M 2" WR

244261 10 CP 680-P/M 3" WR

244262 5 CP 680-P/M 4" WR

244263 1 CP 680-P/M 6" WR

Height Extension (for use with CP 680-P/M) ¿Item No. Qty Description

3424887 10 CP 680-P 2" EXT (red)

3424888 10 CP 680-P 3" EXT (red)

3424889 10 CP 680-P 4" EXT (red)

3424890 1 CP 680-P 6" EXT (red)

3424891 10 CP 680-M 2" EXT (black)

3424892 10 CP 680-M 3" EXT (black)

3424943 10 CP 680-M 4" EXT (black)

3424944 1 CP 680-M 6" EXT (black)

Metal Deck Adapters (for use with CP 680-P/M)Item No. Qty Description

3424945 10 CP 680-P 2" MD (red)

3424946 10 CP 680-P 3" MD (red)

3424947 10 CP 680-P 4" MD (red)

3424948 1 CP 680-P 6" MD (red)

3424949 10 CP 680-M 2" MD (black)

3424950 10 CP 680-M 3" MD (black)

3424951 10 CP 680-M 4" MD (black)

3424952 1 CP 680-M 6" MD (black)

¡

¿

Plasticextension tube

wing clip





39

Chap

ter T

ab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

Top Seal Plug (for use with 2" CP 680-P/M)Iron Pipe SizeItem No. Qty Description

3425366 10 Top Seal, IPS 1/2"Use with CP 680-P/M and 1/2" iron pipe size (Schedule 40)

3425367 10 Top Seal, IPS 3/4"Use with CP 680-P/M and 3/4" iron pipe size (Schedule 40)

3425368 10 Top Seal, IPS 1"Use with CP 680-P/M and 1" iron pipe size (Schedule 40)

3425370 10 Top Seal, IPS 1-1/2"Use with CP 680-P/M and 1-1/2" iron pipe size (Schedule 40)

3425371 10 Top Seal, IPS 2"Use with CP 680-P/M and 2" iron pipe size (Schedule 40)

Copper Pipe SizeItem No. Qty Description

3425372 10 Top Seal, CPS 1/2"Use with CP 680-P/M and 1/2" copper tubing size

3425403 10 Top Seal, CPS 3/4"Use with CP 680-P/M and 3/4" copper tubing size

3425404 10 Top Seal, CPS 1"Use with CP 680-P/M and 1" copper tubing size

3425405 10 Top Seal, CPS 1-1/4"Use with CP 680-P/M and 1-1/4" copper tubing size

3425406 10 Top Seal, CPS 1-1/2"Use with CP 680-P/M and 1-1/2" copper tubing size

3425407 10 Top Seal, CPS 2"Use with CP 680-P/M and 2" copper tubing size

CP 681 Tub Box KitItem No. Qty Description

377920 1 Tub Box Kit Standard — Uncut 10-1/2" Height (with foam insert)Includes tub box, sealing bushing for schedule 40 pipe, (2) legs, flange and styrofoaminlay. Field cut to desired height

3002087* 1 Tub Box Kit Custom — Precut to desired slab thicknessIncludes tub box, sealing bushing for schedule 40 pipe, (2) legs, flange and styrofoaminlay

3410182 Bushing, Standard (1-1/2", Schedule 40)

3009526 Bushing, Thin Wall (1-1/2")

*Item not returnable

Closet StubItem No. Qty Description

3425433 12 Closet Stub, 3"

3425434 12 Closet Stub, 4" ¿

Shower and Floor DrainItem No. Qty Description

3410134 1 Extended Sleeve ¡

3425365 10 Hub Coupling ¬

Aerator Adapters (AA)Item No. Qty Description

244264 1 Aerator Adapter, 3"

244265 1 Aerator Adapter, 4" Ã

¿

¡

¬


Chap

ter

Tab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




40

FS-ONE High Performance Intumescent Firestop SealantItem No. Qty Description Volume

259580 12 FS-ONE, 10.1 oz tube (300 ml) 18 in3 ea ¿

377232 25 FS-ONE, 19.6 oz foil pack (580 ml) 36 in3 ea ¡

259578 1 FS-ONE, 5 gal pail (19 L) 1155 in3 ¬Color is red

CP 601S Elastomeric Firestop SealantItem No. Qty Description Volume

315013 20 CP 601S, 10.5 oz tubes (310 ml) 18 in3 ea ¿

314269 20 CP 601S, 20.2 oz foil pack (600 ml) 36 in3 ea ¡

314270 1 CP 601S, 5 gal pail (19 L) 1155 in3 ¬Color is red

CP 606 Flexible Firestop SealantItem No. Qty Description Color Volume

337756 20 CP 606, 10.5 oz tube (310 ml) Red 18 in3 ¿

314272 20 CP 606, 19.6 oz foil pack (580 ml) White 36 in3 ea ¡

337192 20 CP 606, 19.6 oz foil pack (580 ml) Red 36 in3 ea ¡

314273 1 CP 606 5 gal pail (19 L) White 1155 in3 ¬

337193 1 CP 606, 5 gal pail (19 L) Red 1155 in3 ¬

3426567 60 CP 606, 19.6 oz foil pack (580 ml) Gray 36 in3 ea ¡

CP 604 Self-Leveling Firestop SealantItem No. Qty Description Volume

369637 12 CP 604, 20.2 oz foil pack (600 ml) 36 in3 ea ¿

369177 1 CP 604, 4 gal pail 924 in3 ¡Color is gray

For all sealant dispensers see page 43!

CP 620 Fire FoamItem No. Qty Description

338725 1 CP 620 Fire Foam 10.2 oz tube (300 ml) Includes 12 tubes, 2 mixers and 12 extension pipes

AccessoriesItem No. Qty Description

338720 1 Dispenser ¿

371883 1 CP 620 Deluxe Starter KitIncludes 1 dispenser, 12 cartridges, 24 mixers and 12 extension pipes in animpact-resistant plastic tool box

338718 12 CP 620 Mixer ¡

338716 12 CP 620 Extension Pipe ¬

¡ ¿ ¬

¿ ¡ ¬

¿ ¡

¿ ¡

¿

¡

¬

¬





41

Chap

ter T

ab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

CP 637 Firestop MortarItem No. Qty Description

340645 1 CP 637 Firestop Mortar, 30 lb pail

24155 1 Stainless Steel Mixing ¿

FS 657 Fire BlockItem No. Qty Description Volume

306241 1 FS 657 Fire Block 80 in3

306242 26 FS 657 Fire Block — Case 2,080 in3

CP 675T Firestop Board Item No. Qty Description

304434 1 CP 675T Firestop Board Small 26" x 28" ¡

305688 1 CP 675T Firestop Board Large 26" x 39" ¡


283855 1 CP 675T Z-Frame ¬Includes fasteners for drywall, concrete, block and steel

283854 1 CP 675T T-Separator Bar ÃIncludes fasteners for drywall, concrete, block and steel

283893 5 CP 675T L-SleeveIncludes fasteners for drywall, concrete, block and steel

284094 CP 675T Fastener Kit for surface-mounted boards Includes fasteners for drywall, concrete, block and steel

283856 CP 675T Spare Parts KitIncludes 5 board spacers, 5 turn latches and 5 slide latches

305072 1 CP 619T Putty Roll (1" x 12') ƒ

¡

¿

¬

ƒ

CP 617, CP 617L and CP 617XL Firestop Putty PadItem No. Qty Description Volume

309760 20 CP 617 Putty Pad 6" x 7" 42 in2 ea

333583 20 CP 617L Putty Pad 7" x 7" 49 in2 ea

373387 20 CP 617XL Putty Pad 9" x 9" 81 in2 ea

CP 618 Firestop Putty StickItem No. Qty Description Color Volume

314721 12 CP 618 Putty Stick Red 18 in3 ea

CP 658T Firestop PlugItem No. Qty Description

378287 20 CP 658T Firestop Plug 2"

378288 20 CP 658T Firestop Plug 4"


Chap

ter

Tab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




42

CP 643N Firestop CollarItem No. Qty Description

304325 1 CP 643-50/1.5"NIncludes 1 collar and 2 fastening hooks

304326 1 CP 643-63/2"NIncludes 1 collar and 2 fastening hooks





304345 30 CP 643N Firestop Collar Fastening HooksUse with 50/1.5"N to 160/6"N collars

CP 644 Firestop CollarItem No. Qty Description

304341 1 CP 644 8"Includes 1 collar and 10 fastening hooks

304344 1 CP 644 10"Includes 1 collar and 12 fastening hooks

304346 10 CP 644 Fastening Hooks

CP 648-S Firestop Single Wrap StripItem No. Qty Description

304303 10 CP 648-S Single Wrap Strip 1-1/2"

304304 10 CP 648-S Single Wrap Strip 2"




CP 648-E Firestop Endless Wrap StripItem No. Qty Description

304308 1 CP 648-E Wrap Strip 1" x 33' roll

304309 1 CP 648-E Wrap Strip 1-3/4" x 33' roll

Retaining CollarsItem No. Qty Description

283224 1 CP 648-E Retaining Collar 1" x 25'

283225 1 CP 648-E Retaining Collar 1-3/4" x 25'

29783 10 CP 648-E Retaining Collar Clamps 4"

1. Position Insta-Backclip as per productinstructions.

2. Join drywall over clips.

3. Break off tabs.

Fire-Rated Drywall Repair System Insta-Back Item No. Description Qty/Pkg

68450 Insta-Back Fastener 1/2" 200

68454 Insta-Back Fastener 5/8" 200

¿ ¡ IndentificationItem No. Description

306219 Hilti Firestop System Identification Plate ¿

339611 Hilti Firestop Identification Stickers (100 stickers/roll) ¡





43

Chap

ter T

ab

sA

pp

ilcatio

ns/P

rod

ucts

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

DispensersFoilItem No. Description

24669 Foil Pack (600 ml) Dispenser ¡

334548 Foil Pack (600 ml) Dispenser Replacement Nut

220139 Nozzles for Foil Pack (10/pkg)

Tube55205 300/310 ml Dispenser (CB 200 Pl) ¬

24825 300/310 ml Dispenser (Standard)

Bulk3024001 Bulk Caulk Gun

3009304 Force Flow Bulk Loader

3024002 Follow Plate ƒ

Pneumatic Foil Pack Dispenser Size: Barrel 20-1/2", Handle 7" x 4-1/2" x 1-1/2"Item No. Description

374502 Pneumatic Dispenser

334548 Screw Cap Replacement

3427774 * Orange Plastic Nozzels (1 pack of 35)

374504 Floating Plunger Assembly and Quick Exaust Valve Repair Kit*Item not returnable

¡

¬

ƒ

CP 672 Speed SprayItem No. Description Color

385198 CP 672 Speed Spray — 5 gal pail Red

3423575 CP 672 Speed Spray — 12 pails Red

3423576 CP 672 Speed Spray — 18 pails (1 pallet) Red

3423577 CP 672 Speed Spray — 36 pails (2 pallets) Red

3423578 CP 672 Speed Spray — 18 pail/EPX 2555 Sprayer Combo Red

3423579 CP 672 Speed Spray — 36pail/EPX 2555 Sprayer Combo Red



3427172 CP 672 Speed Spray — 5 gal pail White

AccessoriesItem No. Description

334123 Spray Tech EPX 2555 Heavy-Duty Sprayer ¿

3426208 Spray Tech EPS 2355 Warm-Weather Sprayer

376841 Spray Tech Sprayer Tip .225



376843 Spray Tech Sprayer 3' x 1/4" Whip Hose

376842 Spray Tech Sprayer 3/8" x 1/4" Fitting

¿

CP 767 Speed Strips and CP 777 Speed PlugsCP 777 Speed PlugsItem No. Qty Description Flute Dimensions (L x (Flute) x H)

371925 18 CP 777 1.5" Speed Plug 36" x (3.5" x 4.5") x 1.5"

340998 18 CP 777 2" Speed Plug 36" x (4.5" x 5.5") x 2"

340999 18 CP 777 3" Speed Plug 36" x (5" x 7") x 3"

CP 767 Speed StripsItem No. Qty Description Strip Dimensions (L x W x H)

374507 84 CP 767 2" Speed Strips (1 Hour) 36" x 0.625" x 2"




Bulk Mineral WoolItem No. Qty Description Volume

236993 4 Mineral Wool (46" L x 24" W x 4" H) 17,664 in3

EPX 2555

Firestop Selection Chart

Chap

ter

Tab

s??

Se

lecto

r G

uid

eC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




44

How to use this selection chart1. Identify the penetrating item (metal pipe,

cable trays, insulated metal pipe, etc.)

2. Identify the base material beingpenetrated (concrete, gypsum or wood).

3. Match the two items within theselection chart to identify theapproved Hilti UL/OPL System

1

3

2

Through-Penetration

Fire MaximumBase Rating System Annular SeeMaterial Penetrating Item (F Rating) Hilti Product Used Number Space Page

> Blank Openings

gC Blank Opening (Max. 4" sleeved opening) 3 hr FS 657 Fire Block C-AJ-0055 * 60

gC Max. 24" x 12" opening 3 hr CP 637 Firestop Mortar C-AJ-0082 * 61

gC Blank Opening (Max. 6" diameter opening) 2 hr FS-ONE Intumescent Firestop Sealant C-AJ-0090 * 62

(optional sleeve)

gC Max. 4" (sleeved) opening 2 hr CP 658T Firestop Plug C-A-J 0097 * 63

gC 2", 3", 4" or 6" Cast-In Firestop Device 2 hr CP 680P Cast-In Device with F-A-0005 * 159

CP 618 Putty Stick

gC Blank Opening (Max. 30" x 12" or max. 6" 3 hr CP 604 Self-Leveling Firestop Sealant F-A-0012 * 160

diameter opening)

gC 2", 3" or 4" Cast-In Firestop Device 3 hr CP 680-P/M Cast-In Firestop Device F-A-0014 * 161

gG Blank Opening (Max. 36" x 24") 1 or 2 hr CP 675T Firestop Board W-L-0014 * 275

> Metal Pipe

gC Max 10" steel, cast iron, max. 4" copper, 2 hr FS-ONE Intumescent Firestop Sealant, C-AJ-1149 1-1/4" 65

steel conduit, or EMT CP 606 Flexible Firestop Sealant, or

CP 601S Elastomeric Firestop Sealant, or

CP 604 Self-Leveling Firestop Sealant

gC Max. 10" steel or cast iron, max. 4" copper, 3 hr FS-ONE Intumescent Firestop Sealant C-AJ-1184 3-1/4" 66

steel conduit or EMT (includes Hollow (Top or underside)

Core Concrete)

gC Max. 30" steel, cast iron, max. 6" copper, 3 hr FS-ONE Intumescent Firestop Sealant C-AJ-1226 1-7/8" 67

steel conduit, or max. 4" EMT (optional sleeve)

gC Max. 30" steel, cast iron, max. 6" copper, 2 hr FS-ONE Intumescent Firestop Sealant C-AJ-1291 7/8" 68

steel conduit, or max. 4" EMT

gC Max. 1" flexible steel conduit or flexible steel 2 hr FS-ONE Intumescent Firestop Sealant C-AJ-1346 1-1/4" 69

gas piping

gC Max. 8" steel, cast iron, max. 4" copper, conduit, 3 hr CP 606 Flexible Firestop Sealant C-AJ-1372 1-7/8" 70

or EMT (optional sleeve)

gC Max. 30" steel, cast iron, max. 6" copper, 2 hr FS-ONE Intumescent Firestop Sealant C-AJ-1380 1-7/8" 71

steel conduit, or max. 4" EMT (optional sleeve)

gC Max. 4" steel, cast iron, copper, steel conduit, 2 or 3 hr CP 620 Fire Foam C-AJ-1382 5-7/8" 72

or EMT (optional sleeve)

gC Max. 4" steel, cast iron, copper, steel conduit, 3 hr FS-ONE Intumescent Firestop Sealant or C-AJ-1421 5-3/8" 73

or EMT (optional sleeve) CP 604 Self-Leveling Firestop Sealant

gC Concrete or concrete blockgG GypsumgW Wood

* Refer to UL System.





45

Chap

ter T

ab

sC

hap

ter T

ab

sS

ele

cto

r Guid

eC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s* Refer to UL System.

gC Concrete or concrete block

gG Gypsum

gW Wood


> Metal Pipe (Continued)

gC Max. 30" steel, cast iron, max. 6" copper, 3 hr CP 604 Self-Leveling Firestop Sealant C-AJ-1425 1-7/8" 74


gC Max. 30" steel, cast iron, max. 6" copper, 2 hr CP 606 Flexible Firestop Sealant C-AJ-1435 1-7/8" 75

steel conduit, or max. 4" EMT (sleeved)

gC Max. 30" steel, cast iron, max. 6" copper, steel 2 hr CP 606 Flexible Firestop Sealant C-AJ-1453 1-7/8" 76

conduit, or max. 4" EMT (optional sleeve)

gC Max. 8" steel or cast iron pipe, max. 4" copper 2 hr CP 601S Elastomeric Firestop Sealant C-AJ-1498 2" 77

pipe or tubing, max 6" steel conduit or max. 4"

EMT (optional sleeve)

gC Max. 4" steel conduits or EMT's (one or more) in 2 hr FS-ONE Intumescent Firestop Sealant C-AJ-1513 12" 78

30" x 8" opening

gC Max. 24" steel, cast iron, max. 6" copper, 2 hr CP 606 Flexible Firestop Sealant C-AJ-1517 1-7/8" 79


gC Max. 4" steel, cast iron, steel conduit, 2 hr FS-ONE Intumescent Firestop Sealant C-BJ-1046 1-7/8" 150

or EMT (Hollow Core Concrete)

gC Max. 2" steel, cast iron or ductile iron pipe 2 hr FS-ONE Intumescent Firestop Sealant C-BJ-1055 1-5/8" 151

gC Max. 6" steel, cast iron, copper, steel conduit, or 2 hr CP 680-P/M Cast-In Device F-A-1016 * 162

max. 4" EMT (includes Concrete over Metal Deck)

gC Max. 6" steel, cast iron, copper, steel conduit, or 3 hr CP 680-P/M Cast-In Device F-A-1017 * 164

max. 4" EMT (includes Concrete over Metal Deck)

gC Nom. 3" or 4" steel or cast iron pipe 3 hr CP 680-P/M Cast-In Device with Aerator Adapter F-B-1009 * 201

with cast iron aerator fitting

gC Max. 6” steel or cast iron (2-hour T-rating) 3 hr CP 680-P/M Cast-In Device F-B-1010 * 202

gC Max. 6" steel, cast iron, steel conduit, or 1 hr FS-ONE Intumescent Firestop Sealant F-E-1004 3/4" 228

max. 4" EMT (Concrete Floor/Ceiling Assembly)

gC Max. 4" steel, cast or ductile iron pipe, steel 2 hr FS-ONE Intumescent Firestop Sealant HI/PHV 1-1/2" 234

conduit or EMT (2-hour T-rating) CP 604 Self-Leveling Firestop Sealant 120-01

gC Max. 4" copper pipe or tubing 2 hr FS-ONE Intumescent Firestop Sealant HI/PHV 1-7/8" 237

(2-hour T-rating) CP 604 Self-Leveling Firestop Sealant 120-03

gC Max. 30" steel, cast iron, max. 6" copper, 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-J-1067 2-1/4" 239


gC Max. 6" steel, copper, steel conduit, or 4 hr FS-ONE Intumescent Firestop Sealant W-J-1068 1-1/4" 240

max. 4" EMT pipe (sleeved)

gC Max. 4" steel, cast iron, copper, steel conduit, 1 or 2 hr CP 606 Flexible Firestop Sealant W-J-1124 1/2" 242

or EMT

gC Max. 30" steel, cast iron, max. 6" copper, steel 2 hr CP 606 Flexible Firestop Sealant W-J-1128 1-7/8" 243

conduit, or max. 4" EMT

gG Max. 30" steel, cast iron, max. 6" copper, 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-1054 2-1/4" 276

steel conduit, or max 4" EMT

gG Max. 30" steel, cast iron, max. 6" copper, 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-1164 1-7/8" 277

steel conduit, or max. 4" EMT (sleeved)

gG Max. 8" steel, cast iron, max. 6" steel conduit, 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-1206 1-7/8" 278

max 4" copper or EMT (Shaft Wall)

gG Max. 2" flexible aluminum or steel conduit 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-1243 1" 279

gG Max. 4" steel, cast iron, copper, steel conduit, 4 hr FS-ONE Intumescent Firestop Sealant W-L-1252 7/8" 281

or EMT

gG Max. 30" steel, cast iron, max. 6" copper, 1 or 2 hr CP 606 Flexible Firestop Sealant W-L-1297 * 282



Chap

ter

Tab

s??

Se

lecto

r G

uid

eC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




> Metal Pipe (Continued)

gG Max. 8" steel, cast iron or ductile iron pipe, 2 hr FS-ONE Intumescent Firestop Sealant W-L-1380 7/8" 283

max. 6" copper pipe or tubing, max 4" steel

conduit or EMT

gG Max. 3" steel pipe, steel conduit or EMT 1 or 2 hr FS-ONE Intumescent Firestop Sealant, W-L-1410 1" 286

(membrane penetration) CP 606 Flexible Firestop Sealant,

CP 601S Elastomeric Firestop Sealant or

CP 618 Firestop Putty Stick

gW Max. 4" steel, cast iron, copper, steel conduit 1 or 2 hr FS-ONE Intumescent Firestop Sealant F-C-1009 1" 205

or EMT (Chase Wall Required)

gW Max. 6" steel, cast iron, steel conduit, 1 or 2 hr FS-ONE Intumescent Firestop Sealant F-C-1059 3/4" 206

max. 4" EMT, or max. 2" flexible steel conduit

(Chase Wall Optional)

gW Max. 4" steel, cast iron, copper, conduit, or EMT 1 hr CP 606 Flexible Firestop Sealant F-C-1106 7/8" 207

> Plastic and Glass Pipe

gC Max. 10" PVC, CPVC, max. 6" FRPP or ABS 3 hr CP 643N/644 Firestop Collar C-AJ-2109 * 80

(closed or vented) (optional sleeve)

gC Max. 6" PVC, CPVC, FRPP or ABS 3 hr CP 643N Firestop Collar C-AJ-2110 1-1/4" 82

(closed or vented) (optional sleeve)

gC Max. 6" glass pipe (closed or vented) 3 hr FS-ONE Intumescent Firestop Sealant C-AJ-2118 3-1/2" 84

(optional sleeve)

gC Max. 2" PVC or CPVC (closed or vented) 2 hr FS-ONE Intumescent Firestop Sealant C-AJ-2167 5/8" 85

(includes Hollow Core Concrete)

gC Max. 6" PVDF or max. 4" PP 3 hr CP 643N Firestop Collar C-AJ-2217 3/8" 86

gC Max. 6" PVC, CPVC, FRPP or ABS 2 hr CP 643N Firestop Collar C-AJ-2271 1/2" 87

(closed or vented)

gC Max. 4" PVC, ABS, CPVC or FRPP 3 hr CP 648-E Firestop Wrap Strip with Retaining Collar C-AJ-2336 1/2" 89

(closed or vented) (optional pipe coupling)

gC Max. 3" PVC, ABS, or CPVC (closed or vented) 3 hr CP 648-E/S Firestop Wrap Strip C-AJ-2342 * 91

gC Max. 6" PVC, ABS, or CPVC (closed or vented) 3 hr CP 648-E/S Firestop Wrap Strip with Retaining Collar C-AJ-2371 * 93

gC Max. 4" PVC or CPVC (closed or vented) 2 hr CP 620 Firefoam with C-AJ-2392 5-5/16" 95

CP 648-E/S Firestop Wrap Strip

gC Max. 2" PVC, CPVC, Rigin Nonmetallic Conduit, 2 hr FS-ONE Intumescent Firestop Sealant C-AJ-2407 * 97

ENT, max. 1" optical-fiber raceway, PEX

gC Max. 3" Blazemaster CPVC, Max. 2" Flowguard 3 hr FS-ONE Intumescent Firestop Sealant C-AJ-2451 1-1/4" 98

Gold CPVC (closed system)

gC Max. 4" insulated beverage line (PEX) 2 hr CP 648E Firestop Wrap Strip C-AJ-2468 1-13/16" 99

gC Max. 2" PVC, CPVC, rigid non-metallic conduit 2 hr FS-ONE Intumescent Firestop Sealant C-AJ-2567 * 100

(RNC) or cross-linked polyethylene (PEX)

tubing (closed or vented) (optional sleeve)

gC Max. 2" PVC, CPVC, or RNC 2 hr FS-ONE Intumescent Firestop Sealant C-BJ-2014 1-5/8" 152

(closed piping system) (Hollow Core Concrete)

gC Max. 4" PVC or CPVC (closed or open) 4 hr CP 648-E/S with Retaining Collar C-BJ-2017 1/2" 153

gC Max. 6" PVC, CPVC, FRPP or ABS 2 hr CP 643N Firestop Collar C-BJ-2021 1/2" 154

(closed or vented) (Hollow Core Concrete)



gG Gypsum

gW Wood





47

Chap

ter T

ab

sC

hap

ter T

ab

sS

ele

cto

r Guid

eC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s


> Plastic and Glass Pipe (Continued)

gC Max. 6" PVC, CPVC, FRPP, or ABS 2 hr CP 643N Firestop Collar F-A-2025 1-1/2" 169

(closed or vented) (Concrete over Metal Deck)

gC Max. 6" PVC or CPVC (closed or vented) 2 hr CP 680-P Cast-In Device F-A-2053 * 171

(includes Concrete over Metal Deck)



gC Max. 2" PVC or CPVC (closed or vented) 2 hr FS-ONE Intumescent Firestop Sealant F-A-2058 1" 173


gC Max. 4" ABS, nom. 6" FRPP (closed or vented) 2 hr CP 680-P Cast-In Device F-A-2065 * 174


gC Max. 4" ABS, max. 6" FRPP (closed or vented) 3 hr CP 680-P Cast-In Device F-A-2066 * 175


gC Max. 3" PVC, ABS, or CPVC (closed or vented) 2 hr CP 648-E Firestop Wrap Strip F-A-2068 * 176

(Concrete over Metal Deck)

gC Nom. 4" PVC or ABS with closet flange 3 hr CP 680-P Cast-In Device F-A-2071 * 177


gC Nom. 4" PVC with closet flange 2 hr CP 643N Firestop Collar F-A-2075 1/4" 178



gC Max. 2" PVC with shower drain fitting (includes 2 hr CP 680-P Cast-In Device F-A-2093 * 180

Concrete over Metal Deck)

gC Max. 1-1/2" PVC piping with waste overflow 3 hr CP 681 Tub Box Kit F-A-2094 * 181

tub fittings

gC Max. 6" FRPP plastic pipe, max. 4" ABS, PVDF 2 hr CP 680-P/M Cast-In Device F-A-2141 * 183

or PP plastic pipe (closed or vented)

gC Pipe transition - max. 4" terminating steel, cast 2 hr CP 648-E Firestop Wrap Strip with retaining collar F-A-2154 1-1/2" 184

iron or ductile iron pipe transitioning to max. and FS-ONE Intumescent Firestop Sealant

4" PVC, CPVC or ABS plastic pipe

gC Nominal 2" diameter PVC drain (shower) 3 hr Cast-In Firestop Drain Flange F-A-2156 * 186

gC Max. 4" PVC, ABS, CPVC or rigid non-metallic 3 hr CP 648-S and FS-ONE Intumescent Firestop F-B-2029 * 203

conduit (RNC) (closed or vented) Sealant or CP 601S Elastomeric Firestop Sealant —

For W-rating use CP 604 on top surface of floor

gC Max. 4" PVC or CPVC (closed or vented) 1 hr CP 648-E Firestop Wrap Strip or F-E-2027 * 229

CP 643N Firestop Collar or

FS-ONE Intumescent Firestop Sealant

gC Max. 2" PVC or CPVC (closed system) 2 hr FS-ONE Intumescent Firestop Sealant W-J-2072 5/8" 246

gC Max. 6" PVC or CPVC (closed or vented) 4 hr CP 643N Firestop Collar W-J-2091 * 247

gC Max. 2" PVC or CPVC (closed or vented) 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-J-2108 11/16" 248

(sleeve optional)

gC Max. 6" PVC or CPVC; Max. 4" ABS 1 or 2 hr CP 648-S Firestop Wrap Strip W-J-2205 * 249

(closed or vented)

gG Max. 10" PVC, CPVC, ABS, FRPP, or max. 1 or 2 hr CP 643N / CP 644 Firestop Collar W-L-2078 1/2" 287

4" PVDF (closed or vented)

gG Max. 2" PVC, CPVC (or vented) (optional sleeve) 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-2128 11/16" 289

gG Max. 2" Fiber Optic Raceway (Innerduct) or ENT 2 hr FS-ONE Intumescent Firestop Sealant W-L-2165 3/8" 290



gG Gypsum

gW Wood


Chap

ter

Tab

s??

Se

lecto

r G

uid

eC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




48


> Plastic and Glass Pipe (Continued)

gG Max. 1" Cross-linked polyethylene (PEX) SDR9 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-2186 1-3/8" 291

tubing (closed system only) (optional sleeve)

gG Max. 2" PVC or CPVC (closed system) 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-2244 5/8" 292

gG Max. 6" PVC or CPVC (closed or vented) 4 hr CP 643N Firestop Collar W-L-2245 1/2" 293

gG Max. 6" Glass (Schott Scientific Glass) 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-2330 1-1/4" 294

gG Max. 4" PVC, ABS, CPVC (closed or vented) 1 or 2 hr CP 648-E Firestop Wrap Strip with Sleeve W-L-2340 3/4" 295

gG Max. 2" Blazemaster CPVC or Flowguard 1or 2 hr FS-ONE Intumescent Firestop Sealant W-L-2377 1-1/4" 296

Gold CPVC (closed system)

gG Max. 6" PVC, CPVC, max. 4" ABS 1or 2 hr CP 648-E Firestop Wrap Strip W-L-2406 * 298

gG Max. 4" PVC, CPVC, ABS or FRPP (closed or 1 or 2 hr CP 648-E Firestop Wrap Strip W-L-2411 1/2" 299

vented) (optional pipe coupling)

gW Max. 4" PVC, CPVC, ABS, or FRPP 1 or 2 hr CP 643N Firestop Collar F-C-2030 1/2" 208

(closed or vented) (Chase Wall Required)

gW Max. 2" PVC, CPVC or ABS (closed or vented) 1 or 2 hr CP 643N Firestop Collar F-C-2128 5/8" 209


gW Max. 2" PVC or CPVC (closed or vented) 1 or 2 hr FS-ONE Intumescent Firestop Sealant F-C-2160 1-1/8" 210


gW Nominal 4" ABS or PVC with closet flange 1 hr FS-ONE Intumescent Firestop Sealant F-C-2203 * 211

gW Maximum 1-1/2" PVC or ABS drain fittings with 1 hr FS-ONE Intumescent Firestop Sealant F-C-2204 1" 212

bathtub waste/overflow fittings

gW Max. 4" PVC, CPVC (closed or vented) 1 hr CP 648-E Firestop Wrap Strip with Retaining Collar F-C-2232 1/2" 213

or CP 643N Firestop Collar

gW Max. 3" Blazemaster CPVC, Max. 2" 1 hr FS-ONE Intumescent Firestop Sealant F-C-2270 5/8" 214

Flowguard Gold )

gW Max. 1" Cross-linked polyethylene (PEX) SDR9 1 hr FS-ONE Intumescent Firestop Sealant F-C-2334 7/8" 215

tubing (closed or vented)

> Cables/Cable Trays

gC Cable bundle (various cables) (optional sleeve) 3 hr FS-ONE Intumescent Firestop Sealant C-AJ-3095 * 101

gC Cable bundle (various cables) (optional sleeve) 3 hr FS-ONE Intumescent Firestop Sealant C-AJ-3180 * 102

gC Cable bundle (various cables) (optional sleeve) 3 hr CP 606 Flexible Firestop Sealant C-AJ-3181 1-7/8" 103

gC Cable bundle (various cables) (optional sleeve) 3 hr CP 604 Self-Leveling Firestop Sealant C-AJ-3193 1" 104

gC Cable bundle (various cables) (optional steel or 3 hr CP 618 Firestop Putty Stick C-AJ-3208 1" 105

PVC sleeve)

gC Cable bundle (various cables) (optional sleeve) 3 hr CP 618 Firestop Putty Stick C-AJ-3210 1" 106

gC Cable bundle (various cables) (optional sleeve) 3 hr CP 658T Firestop Plug C-AJ-3216 3" 107

gC Cable bundle (various cables) (optional sleeve) 3 hr FS-ONE Intumescent Firestop Sealant C-AJ-3239 2-1/2" 108

gC Cable tray (various cables) 3 hr FS 657 Fire Block C-AJ-4034 13-1/2" 109

gC Cable Trays (various cables) 3 hr FS 657 Fire Block C-AJ-4035 4" 111

gC Cable Tray (various cables) 2 hr FS-ONE Intumescent Firestop Sealant C-AJ-4071 6" 112

gC Cable rack (various cables) 2 hr CP 675T Firestop Board and FS 657 Fire Block C-AJ-4077 28" 113

with frame components

gC Cable bundle (various cables) 2 hr FS-ONE Intumescent Firestop Sealant C-BJ-3024 1" 155

(Hollow Core Concrete)

gC Cable bundle (various cables) 3 hr CP 680-P/M Cast-In Device with F-A-3007 * 187

CP 618 Putty Stick* Refer to UL System.


gG Gypsum

gW Wood





49

Chap

ter T

ab

sC

hap

ter T

ab

sS

ele

cto

r Guid

eC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s


> Cables/Cable Trays (Continued)

gC Cable bundle (various cables) (concrete floor or 3 hr CP 680-P/M Cast-In Device F-A-3033 * 189

concrete over metal deck)

gC Cable Tray 2 hr CP 604 Self-Leveling Firestop Sealant F-A-4003 6" 190

gC Cable bundle (various cables) (Concrete Floor/ 1 hr FS-ONE Intumescent Firestop Sealant F-E-3005 * 231

Ceiling Assembly)

gC Cable bundle (various cables) (optional sleeve) 2 hr CP 618 Firestop Putty Stick W-J-3036 * 251

gC Cable bundle (various cables) (optional sleeve) 2 hr FS-ONE Intumescent Firestop Sealant W-J-3060 1" 252

gC Cable bundle (various cables) (PVC Sleeve) 2 hr CP 618 Firestop Putty Stick W-J-3092 1-3/8" 253

gC Cable bundle (various cables) (optional sleeve) 2 hr CP 658T Firestop Plug W-J-3143 1" 254

gC Cable tray (various cables) 2 hr FS 657 Fire Block W-J-4029 26" 255

gC Cable tray (various cables) 2 hr CP 675T Firestop Board W-J-4048 34" 257

gC Cable trays (various cables) 2 hr CP 675T Firestop Board and W-J-4050 * 259

FS 657 Fire Block with frame components

gG Cable bundle (various cables) (optional sleeve) 1 or 2 hr FS-ONE Intumescent Firestop Sealant, W-L-3065 1" 302

CP 601S Elastomeric Firestop Sealant, or

CP 606 Flexible Firestop Sealant

gG SER Cables 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-3071 1-1/2" 304

gG Cable bundle (various cables) (optional sleeve) 1 or 2 hr CP 618 Firestop Putty Stick W-L-3111 * 305

gG Cable bundle (various cables) 1 or 2-hr CP 618 Firestop Putty Stick W-L-3122 * 306

(Unique Firestop Sleeve)

gG Cable bundle (various cables) (sleeved) 4 hr FS-ONE Intumescent Firestop Sealant W-L-3139 1" 307

gG Cable bundle (various cables) (Shaft Wall) 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-3161 3/4" 308

gG Cable bundle (various cables)(PVC sleeve) 1 or 2-hr CP 618 Firestop Putty Stick W-L-3213 1-3/8" 309

gG Cable bundle (various cables) 1 or 2 hr CP 658T Firestop Plug W-L-3272 1" 310

gG Cable bundle (various cables)(sleeved) 1 or 2 hr FS-ONE Intumescent Firestop Sealant, W-L-3320 1" 311

CP 606 Flexible Firestop Sealant,

CP 601S Elastomeric Firestop Sealant or

CP 618 Firestop Putty Stick

gG Cable tray (various cables) 1 or 2 hr FS 657 Fire Block W-L-4011 4" 313

gG Cable tray (various cables) 1 or 2 hr FS 657 Fire Block W-L-4038 26" 314

gG Cable tray (various cables) 2 hr CP 675T Firestop Board W-L-4048 34" 316

gG Cable trays (various cables) 2 hr CP 675T Firestop Board and W-L-4050 * 318

FS 657 Fire Block with frame components

gG Cable tray (various cables) 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-4060 3" 322

gW Cable bundle (various cables) 1 or 2 hr FS-ONE Intumescent Firestop Sealant F-C-3012 * 216

(Chase Wall Required)

gW Cable bundle (various cables) 1 hr FS-ONE Intumescent Firestop Sealant F-C-3044 3/4" 217


gW Cable bundle (various cables) 1 hr CP 606 Flexible Firestop Sealant F-C-3074 1" 218

(chase wall optional)

> Insulated Metal Pipe

gC Max. 2" steel with max. 1" glass fiber insulation 2 hr FS-ONE Intumescent Firestop Sealant, C-AJ-5048 3-1/16" 115

CP 601S Elastomeric Firestop Sealant,

CP 606 FlexibleFirestop Sealant, or




gG Gypsum

gW Wood


> Insulated Metal Pipe (Continued)

gC Max. 20" steel, max. 6" copper with max. 3" 3 hr FS-ONE Intumescent Firestop Sealant C-AJ-5061 * 116

glass fiber insulation

gC Max. 4" steel or copper with max. 3/4" 3 hr FS-ONE Intumescent Firestop Sealant C-AJ-5090 1-1/2" 117

AB/PVC insulation

gC Max. 12" steel, max. 6" copper with nom. 2" 2 hr FS-ONE Intumescent Firestop Sealant C-AJ-5091 2-1/4" 118

glass fiber or max. 2" calcium silicate

gC Max. 12" steel, max. 6" copper with max. 1-1/2" 2 hr FS-ONE Intumescent Firestop Sealant C-AJ-5096 1-7/8" 119

glass fiber insulation (optional sleeve)

gC Max. 4" steel or copper pipe with 3/4" 2 hr FS-ONE Intumescent Firestop Sealant C-AJ-5198 1-3/8" 120

AB/PVC insulation

gC Max 12" steel or max. 6" copper with nominal 2 hr FS-ONE Intumescent Firestop Sealant C-AJ-5277 1-7/8" 121

1-1/2" or 3" FOAMGLAS® insulation

gC Max. 6" steel, cast iron, ductile iron pipe or 2 hr FS-ONE Intumescent Firestop Sealant C-AJ-5301 1-7/8" 122

copper pipe or tubing with 2" glass-fiber pipe

insulation

gC Max. 4" steel or copper pipe with 1" glass-fiber 2 hr FS-ONE Intumescent Firestop Sealant C-BJ-5013 7/8" 156

pipe insulation

gC Max. 2" steel, cast iron, ductile iron pipe or 2 hr FS-ONE Intumescent Firestop Sealant C-BJ-5015 1-7/8" 157

copper pipe or tubing with 1" glass-fiber

pipe insulation

gC Max. 4" steel, copper pipe or copper tubing 3 hr FS-ONE Intumescent Firestop Sealant C-BJ-5018 7/8" 158

with 1" AB/PVC pipe insulation

gC Max. 4" steel or copper pipe with nom. 3/4" or 1" 2 hr CP 680-P/M Cast-In Device F-A-5015 * 191

AB/PVC insulation (includes Concrete

over Metal Deck)

gC Max. 4" steel or copper pipe with nom. 3/4" or 1" 3 hr CP 680-P/M Cast-In Device F-A-5016 * 192

AB/PVC insulation (includes Concrete

over Metal Deck)

gC Max. 4" steel or copper pipe with 1", 1-1/2" 2 hr CP 680-P/M Cast-In Device F-A-5017 * 193

or 2" glass fiber insulation (includes Conrete

over Metal Deck)

gC Max. 4" steel or copper pipe with 1", 1-1/2" or 3 hr CP 680-P/M Cast-In Device F-A-5018 * 194

2" glassfiber insulation (includes Concrete

over Metal Deck)

gC Max. 2" steel, copper with 1-1/2" glass-fiber 1 hr FS-ONE Intumescent Firestop Sealant F-E-5002 1" 232

insulation (Concrete Floor/Ceiling Assembly)

gC Max. 2" steel, copper with 3/4" AB/PVC 1 hr FS-ONE Intumescent Firestop Sealant F-E-5004 1" 233

insulation (Concrete Floor/Ceiling Assembly)

gC Max. 4" steel, EMT, or steel conduit, max. 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-J-5041 1-1/2" 263

2" Copper with 3/4" AB/PVC insulation

gC Max. 12" steel, max. 6" copper, max. 4" 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-J-5042 1-1/2" 264

steel conduit, EMT with maximum 2" glass-fiber

insulation

gG Max. 4" steel, steel conduit, EMT, or max. 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-5028 1-1/2" 323

2" copper with 3/4" AB/PVC insulation


Chap

ter

Tab

s??

Se

lecto

r G

uid

eC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




50



gG Gypsum

gW Wood





51

Chap

ter T

ab

sC

hap

ter T

ab

sS

ele

cto

r Guid

eC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s


> Insulated Metal Pipe (Continued)

gG Max. 12" steel, max. 6" copper, max. 4" 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-5029 1-7/8" 324

steel conduit or EMT with 1", 1-1/2" or 2"

glass fiber insulation or max. 2" calcium

silicate insulation

gG Max. 10" steel, max. 4" copper pipe with max. 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-5096 * 326

2" glass fiber insulation

gG Max. 1" copper with 3/4" AB/PVC insulation 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-5143 1-1/8" 327

(Shaft Wall)

gG Max 12" steel or max. 6" copper with nominal 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-5223 1-1/4" 328

1-1/2" or 3" Foamglas insulation

gG Nom. 4" PVC or CPVC with nominal 1-1/2" 1 or 2 hr CP 648-E Firestop Wrap Strip with retaining collar W-L-5225 1" 329


gG Max. 2" steel, cast iron, ductile iron pipe or 2 hr CP 648-E Firestop Wrap Strip W-L-5244 13/16" 330

copper pipe or tubing with 2" glass-fiber pipe

insulation (sleeved) (shaft wall)

gG Max. 4" steel, cast iron, ductile iron pipe or 2 hr FS-ONE Intumescent Firestop Sealant, CP 606 W-L-5257 7/8" 332

copper pipe or tubing with 1-1/2" glass-fiber Flexible Firestop Sealant or CP 601S Elastomeric

pipe insulation Firestop Sealant

gW Max 2" steel, copper, steel conduit or EMT 1 or 2 hr FS-ONE Intumescent Firestop Sealant F-C-5004 * 219

with nom. 1/2" glass fiber or nom. 3/4" AB/PVC

insulation (Chase Wall Required)

gW Max. 2" copper or steel pipe with max. 1-1/2" 1 hr FS-ONE Intumescent Firestop Sealant F-C-5036 1" 220

glass fiber insulation (Chase Wall Optional)

gW Max. 2" copper or steel pipe with max. 3/4" 1 or 2 hr FS-ONE Intumescent Firestop Sealant F-C-5037 1" 221

AB/PVC insulation (Chase Wall Optional)

gW Max. 4" steel, cast iron, or copper with 3/4" 1 hr CP 606 Flexible Firestop Sealant F-C-5065 7/8" 222

AB/PVC insulation (chase wall optional)

gW Max. 4" steel, cast iron, or copper with 3/4" 1 hr CP 606 Flexible Firestop Sealant F-C-5066 7/8" 223

glass fiber insulation (chase wall optional)

> Electrical Busways

gC Electrical Busway 3 hr CP 637 Firestop Mortar C-AJ-6006 * 123

gC Electrical Busway 3 hr FS-ONE Intumescent Firestop Sealant C-AJ-6017 2" 124

gC Electrical Busway 2 hr CP 620 Fire Foam C-AJ-6036 5-3/4" 125

gC Electrical Busway 2 hr CP 604 Self Leveling Firestop Sealant F-A-6002 6-1/2" 197

gG Electrical Busway 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-6019 1-1/4" 333

> Metal Ducts / Mechanical Support

gC Max. 32" x 32" sheet metal duct without damper 3 hr CP 601S Elastomeric Firestop Sealant or C-AJ-7046 1-1/2" 126


gC Max. 30" x 30" sheet metal duct without damper 3 hr CP 606 Flexible Firestop Sealant or C-AJ-7051 1-3/4" 127


gC Max. 20" spiral wound duct (min. 24 ga.) 2 hr CP 601S Elastmeric Firestop Sealant, C-AJ-7084 1-1/2" 128

without damperor max. 12" spiral wound duct CP 606 Flexible Firestop Sealant,

(min. 28 ga.) without damper CP 604 Self Leveling Firestop Sealant, or




gG Gypsum

gW Wood


Chap

ter

Tab

s??

Se

lecto

r G

uid

eC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




52


> Metal Ducts / Mechanical Support (continued)

gC Max. 24" x 12" sheet metal duct (without damper) 2 hr FS-ONE Intumescent Firestop Sealant C-AJ-7104 2" 129

gC Max. 30" x 30" sheet metal duct (without damper) 2 hr FS-One Intumescent Firestop Sealant C-AJ-7111 1-3/4" 130

gC Max. 48" x 24" sheet metal duct without damper 1 or 2 hr CP 601S Elastomeric Firestop Sealant, W-J-7021 2" 265

CP 606 Flexible Firestop Sealant, or


gC Max. 20" spiral wound duct without damper, or 1 or 2 hr CP 601S Elastomeric Firestop Sealant, W-J-7022 1-1/2" 266

12" sheet metal duct CP 606 Flexible Firestop Sealant, or


gC Max. 24" x 24" sheet metal duct (without damper) 2 hr CP 606 Flexible Firestop Sealant W-J-7085 1" 268

gG Max. 20" spiral wound duct without damper, or 1 or 2 hr CP 601S Elastomeric Firestop Sealant, W-L-7042 1-1/2" 334

12" sheet metal duct CP 606 Flexible Firestop Sealant, or


gG Steel channel or "H" strut, steel cable, threaded 1 or 2 hr FS ONE Intumescent Firestop Sealant or W-L-7130 7/8" 336

steel rod or steel angle CP 606 Flexible Firestop Sealant

gG Max. 24" x 24" sheet metal duct 1 or 2 hr CP 606 Flexible Firestop Sealant W-L-7143 1" 337

gG Max. 100" x 100" sheet metal duct meeting 1 or 2 hr CP 606 Flexible Firestop Sealant W-L-7155 2" 339

SMACNA construction standards

gW Max 4" diameter sheet metal duct without 1 hr FS-ONE Intumescent Firestop Sealant F-C-7013 3/4" 224

damper (Chase Wall Optional)

gW Max. 4" sheet metal duct without damper 1 hr CP 606 Flexible Firestop Sealant F-C-7025 1" 225

(chase wall optional)

> Insulated Metal Ducts

gC Max. 24" x 12" sheet metal duct with 1-1/2" 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-J-7029 1" 267


gC Max. 48" x 24" galv. sheet metal duct with max. 2 hr FS-ONE Intumescent Firestop Sealant W-J-7091 1-1/4" 269

1-1/2" glass-fiber duct insulation with

foil-scrim-kraft facing

gG Max. 24" x 12" sheet metal duct without 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-7059 1" 335

damper with max. 1-1/2" thickness foil scrim

glass fiber duct insulation

gG Max. 48" x 24" galv. sheet metal duct with 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-7151 1-1/4" 338

max. 1-1/2" glass-fiber duct insulation with

foil-scrim-kraft facing

> Large Opening/Multiple Penetations

gC Max. 12" steel, max. 4" copper, steel conduit 3 hr CP 637 Firestop Mortar C-AJ-1140 * 64

or EMT

gC Max. 4" steel conduit or EMT (one or more) 2 hr FS-ONE Intumescent Firestop Sealant C-AJ-1513 12" 78

gC Max. 2" PVC ENT, max. 1-1/4" PE ENT 3 hr CP 648-E/S Firestop Wrap Strip with Retaining Collar C-AJ-2402 * 96

gC Insulated or non-insulated steel, cast iron, 3 hr FS 657 Fire Block C-AJ-8056 * 131

copper,steel conduit or EMT, cable tray or

cables (single or bundled)

gC Steel, cast iron, copper, steel conduit, EMT, 4 hr CP 637 Firestop Mortar C-AJ-8095 * 133

or cable trays



gG Gypsum

gW Wood


> Large Openings / Multiple Penetrations (continued)

gC Insulted or non-insulated steel, cast iron, copper, 2 hr CP 620 Fire Foam C-AJ-8096 * 134

conduit, or EMT pipes, cables, PVC plastic pipe

gC Multiple insulated and non-insulated steel, 3 hr FS-ONE Intumescent Firestop Sealant C-AJ-8099 * 137

cast iron, copper, steel conduit, or EMT and

cable bundle

gC Multiple insulated and non-insulated copper 3 hr FS 657 Fire Block C-AJ-8100 * 139

pipe and cable bundle

gC Non-Insulated steel, cast iron, copper, steel 3 hr FS 657 Fire Block C-AJ-8110 * 140

conduit or EMT, fiber optic raceways, or cable

conduittrays

gC Multple insulated or non-insulated metallic pipes, 2 hr FS-ONE Intumescent Firestop Sealant C-AJ-8143 12" 142

conduits and cables (single or bundled)

gC HVAC line set (optional sleeve) 2 hr FS-ONE Intumescent Firestop Sealant C-AJ-8148 * 144

gC Insulated or non-insulated steel, cast or ductile 2 hr CP 648-E Firestop Wrap Strip or CP 648-S Firestop C-AJ-8177 * 145

iron pipe, copper pipe or tubing; PVC, CPVC or Wrap Strip and CP 637 Firestop Mortar

RNC plastic pipe, sheet metal duct or cable

bundle (various cables)

gC HVAC line set 2 hr FS-ONE Intumescent Firestop Sealant and C-AJ-8178 1" 148

CP 643N Firestop Collar

gC Max. 1" steel conduits, cast iron, steel or 3 hr CP 680-P/M Cast-In Device F-A-1022 2" 166

copper pipe or EMT (includes Concrete

over Metal Deck) (max. penetrants = 5)

gC Max. 2" or 3" steel conduits, cast iron, steel or

copper pipe or EMT (includes Concrete 3 hr CP 680-P/M Cast-In Device F-A-1023 2" 167

over Metal Deck) (max. penetrants = 2)

gC Max. 1-1/2" steel pipe, EMT or steel conduit, 3 hr CP 680-P/M Cast-In Device F-A-1066 1-1/2" 168

Copper pipe or tubing

gC Max. 2" PVC, CPVC, or max. 1" ENT 2 hr CP 680-P Cast-In Device F-A-2103 * 182

(max. qty = 3) (includes Concrete over Metal Deck)

gC Multiple insulated metallic pipes 2 hr CP 604 Self Leveling Firestop Sealant F-A-5032 2" 196

gC Insulated steel, cast or ductile iron pipe, 2 hr CP 604 Self Leveling Firestop Sealant F-A-5036 2" 196

copper pipe or tubing

gC Insulated or non-insulated metallic pipes, 2 hr CP 604 Self Leveling Firestop Sealant F-A-8012 12" 198

conduits andcables (single or bundled) in

max. 30" x 48" opening

gC Multiple HVAC line sets 3 hr CP 680-P/M Cast-In Device F-A-8016 * 200

gC Max. 2” steel conduit or EMT (one or more) 1 or 2 hr CP 620 Fire Foam W-J-1116 * 241

gC Multiple max. 2" steel pipe, steel conduit or EMT 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-J-1191 * 244

gC Multiple max. 4" steel pipe, steel conduit or EMT 2 hr FS-ONE Intumescent Firestop Sealant W-J-1202 * 245

gC Insulated or non-insulated steel, cast iron, 4 hr FS 657 Fire Block W-J-8007 * 270

copper, steel conduit or EMT pipes, cable tray

or cables (single or bundled)

gC Insulated or non-insulated metallic, non-metallic 2 hr FS-ONE Intumescent Firestop Sealant W-J-8035 * 272

pipes and cable bundle





53

Chap

ter T

ab

sC

hap

ter T

ab

sS

ele

cto

r Guid

eC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s



gG Gypsum

gW Wood


Chap

ter

Tab

s??

Se

lecto

r G

uid

eC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




54


> Large Openings / Multiple Penetrations (continued)

gC Max. 2" metallic pipe, ENT and cable bundle 2 hr FS-ONE Intumescent Firestop Sealant W-J-8039 * 274

gG Multiple max. 2" steel conduits or EMT 1 or 2 hr CP 620 Fire Foam W-L-1249 * 280

gG Multiple max. 2" steel pipe, steel conduit or EMT 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-1389 * 284

gG Multiple max. 4" steel pipe, steel conduit or EMT 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-1408 * 285

gG Multiple max. 4" diameter bundle of max. 1" 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-2467 1" 301

PEX tubing (SDR9) (closed system)

gG Insulated or non-insulated steel, copper, steel 1 or 2 hr FS 657 Fire Block W-L-8013 * 340

conduit or EMT pipes, plastic pipe, cable tray or

cables (single or bundled)

gG Insulated or non-insulated steel, cast iron, copper, 1,2,3, FS 657 Fire Block W-L-8014 * 342

steel conduit or EMT pipes, plastic pipe, cable or 4 hr

tray or cables (single or bundled)

gG Insulated or non-insulated steel, cast iron, copper, 1 or 2 hr CP 620 Fire Foam W-L-8019 * 345

conduit, or EMT pipes, cables, PVC plastic pipe,

flexible conduit, and sheet metal duct

gG HVAC Line Set 2 hr FS-ONE Intumescent Firestop Sealant W-L-8047 1-1/4" 348

gG Multple metallic penetrants, cable bundle 1 or 2 hr CP 675T Firestop Board W-L-8059 1" 349

(various cables)

gG Insulated or non-insulated metallic, non-metallic 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-8065 5" 350

pipes and cable bundle

gG Max. 2” steel, cast iron, conduit, EMT, flexible 1 or 2 hr FS-ONE Intumescent Firestop Sealant W-L-8071 * 352

gas piping, or ENT, max. 4” cable bundle

gW Multiple HVAC line set (Chase Wall Optional) 1 hr FS-ONE Intumescent Firestop Sealant F-C-8026 1" 226

gW Double HVAC Line Set (no pvc drain) 1 hr CP 606 Flexible Firestop Sealant F-C-8032 1" 227

> Wall Opening Protective Materials

gG UL listed metallic or non-metallic outlet boxes 1 or 2 hr CP 617 Firestop Putty Pads CLIV * 354



gG Gypsum

gW Wood





55

Chap

ter T

ab

sC

hap

ter T

ab

sS

ele

cto

r Guid

eC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s

Joint

Fire Max. Joint Hilti SealantBase Rating Width Movement Produuct System Depth SeeMaterial Type of Joint — Description (F Rating) (inches) Capability Used Number (inches) Page

> Floor to floor, wall to floor and wall to wall joints

gC Concrete floor to floor joint 2 hr 3-3/4" 7% CP 606 FF-D-1012 1/2" 409

gC Concrete floor to floor joint 2 hr 3-1/2" 14% CP 672 FF-D-1013 1/8" 410

gC Concrete floor to floor joint 2 hr 6" 10% CP 604 FF-D-1039 1/2" 411

gC Concrete floor to floor joint 4 hr 2" 12.5% CP 601s FF-D-1047 1/2" 412

gC Concrete floor to wall joint 2 hr 3-3/4" 7% CP 606 FW-D-1012 1/2" 413

gC Concrete floor to wall joint 2 hr 3-1/2" 14% CP 672 FW-D-1013 1/8" 414

gC Concrete floor to wall joint 2 hr 6" 10% CP 604 FW-D-1037 1/2" 415

gC Concrete floor to wall joint 4 hr` 2" 12.5% CP 601s FW-D-1047 1/2" 416

gC Concrete or block wall perpendicular and parallel to 2 hr 3/4" 33% CP 606 HW-D-0081 1/2" 421

concrete over metal deck (includes roof deck)

(top of wall)

gC Concrete or block wall to concrete over metal deck with 2 hr 1" 12.5% CP 672 HW-D-0181 1/8" 427

optional use of spray-on fireproofing (parallel)

(top-of-wall)

gC Concrete or block wall perpendicular to concrete over 2 hr 2-1/4" 11% CP 606 HW-D-0225 1/2" 432

metal deck (top-of-wall)

gC Concrete or block wall parallel to concrete over metal 2 hr 1" 25% CP 672 HW-D-0258 1/8" 433

deck with spray-on fireproofing (I beam/bar joist

through joint) (top of wall)

gC Concrete or block wall to concrete floor (top of wall) 4 hr 2" 12.5% CP 601s HW-D-0261 1/2" 437

gC Concrete or block wall to concrete floor or hollow core 2 hr 1" 12.5% CP 606 HW-D-0268 1/2" 439

floor (Sealant only) (top of wall)

gC Concrete or block wall perpendiular to concrete over 2 hr 2" 12.5% CP 672 HW-D-0285 1/8" 440

metal deck (includes roof deck) (top of wall — one

side access)

gC Concrete or block wall parallel to concrete over metal 2 hr 2" 12.5% CP 672 HW-D-0286 1/8" 441

deck (includes roof deck) (top of wall - one side access)

gC Concrete or block wall perpendicular to concrete floor 4 hr 1" 12.5% CP 672 HW-D-0294 1/8" 443

over metal deck (top-of-wall)

gC Concrete or block wall to concrete floor (top-of-wall) 2 hr 3-3/4" 7% CP 606 HW-D-1009 1/2" 450

gC Concrete or block wall perpendicular to concrete 2 hr 3-1/2" 14% CP 672 HW-D-1037 1/8" 451

over metal deck with optional use of spray-on

fireproofing (top of wall)

gC Concrete or block wall to concrete floor (top of wall) 4 hr 2" 12.5% CP 601s HW-D-1042 1/2" 452

gC Concrete or block wall to concrete floor 3 hr 3-1/4" 25% CP 672 HW-D-1058 1/8" 453

gC Concrete or block wall to wall joint 2 hr 2" 12.5% CP 672 WW-D-0017 1/8" 456

gC Concrete or block wall to wall joint (sealant only) 2 hr 1" 12.5% CP 606 WW-D-0032 1/2" 457

gC Concrete or block wall perpendicular to gypsum 1 or 2 hr 3/4" 17% CP 606, WW-D-0040 5/8" 458

wall (wall to wall) (Sealant only) CP 601s

gC Concrete or block wall to wall joint 2 hr 3-3/4" 7% CP 606 WW-D-1012 1/2" 460

gC Concrete or block wall to wall joint 4 hr 2" 12.5% CP 601s WW-D-1047 1/2" 461

gG Gypsum wall perpendicular to concrete over metal 1 or 2 hr 1" 50% CP 672 HW-D-0042 1/8" 417

deck with optional use of spray-on fireproofing

(includes roof deck) (top-of-wall)


gG Gypsum

gW Wood


Chap

ter

Tab

s??

Se

lecto

r G

uid

eC

hap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

s




56


> Floor to floor, wall to floor and wall to wall joints (continued)

gG Gypsum wall perpendicular to concrete over metal 1 or 2 hr 3/4" 33% CP 606 HW-D-0045 1/2" 419

deck (includes roof deck) (top-of-wall)

gG Gypsum wall parallel to concrete over metal deck with 1 or 2 hr 1" 50% CP 672 HW-D-0049 1/8" 420

optional use of spray-on fireproofing (includes roof

deck) (top-of-wall)

gG Gypsum wall perpendicular to concrete over metal 1 or 2 hr 2" 20% CP 672 HW-D-0087 1/8" 422

deck with optional use of spray-on fireproofing


gG Gypsum wall parallel to concrete over metal deck with 1 or 2 hr 2" 20% CP 672 HW-D-0089 1/8" 424

optional use of spray-on fireproofing


gG Gypsum wall to concrete floor or hollow core 1 or 2 hr 2" 20% CP 672 HW-D-0106 1/8" 426

concrete (top-of-wall)

gG Gypsum wall parallel to concrete over metal deck 1 or 2 hr 3/4" 17% CP 606 HW-D-0184 5/8" 428

with optional use of spray-on fireproofing

(includes roof deck) (top-of-wall) (sealant only)

gG Gypsum wall to concrete floor or hollow core concrete 1 or 2 hr 3/4" 17% CP 606 HW-D-0209 5/8" 429

(top-of-wall)

gG Gypsum wall parallel to concrete over metal deck 1 or 2 hr 1" 25% CP 672 HW-D-0218 1/8" 430

with spray-on fireproofing (top of wall)

(beam/bar joist through joint)

gG Gypsum wall to underside of steel beam and concrete 1 or 2 hr 1" 25% CP 672 HW-D-0259 1/8" 435

over metal deck with spray-on fireproofing (top-of-wall)

gG Gypsum wall parallel to concrete over metal deck (wall 1 or 2 hr 1" 18.75% CP 672 HW-D-0264 1/8" 438

not centered under lower plane of flute) (top of wall)

gG Gypsum wall perpendicular to concrete over metal 1, 2, 3, 1" 12.5% CP 672 HW-D-0292 1/8" 442

deck (top of wall) or 4 hr

gG Gypsum wall (cut to profile) perpendicular to concrete 1 or 2 hr 3/4" 17% CP 606 HW-D-0324 5/8" 444

over metal deck with optional use of spray-on

fireproofing (sealant only)(top-of-wall)

gG Gypsum shaft wall to concrete floor (top of wall) 2 hr 3/4" 8% CP 606 HW-D-0342 1" 445

gG Top of gypsum wall assembly to concrete over metal 1 or 2 hr 1" 12.5% CP 672 HW-D-0388 1/8" 446

deck floor/roof assembly

gG Top of concrete or block wall to fluted steel roof deck 2 hr 1" 12.5% CP 672 HW-D-0389 1/8" 448

gG Gypsum wall to bottom of offset I-beam with Z-bar 1 or 2 hr 1" - CP 672 HW-S-0069 1/8" 454

extensions

gG Gypsum wall to wall joint 1 or 2 hr 2" 12.5% CP 606 WW-D-0067 1/2" 459


gG Gypsum

gW Wood





57

Chap

ter T

ab

sC

hap

ter T

ab

sS

ele

cto

r Guid

eC

hap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

s


> Curtain Wall Joints

Glass spandrel with aluminum framing 2 hr 6" - CP 672 CEJ-127-P 1/8" 356

Concrete panels with steel framing 2 hr 8" 9.5% CP 672 CEJ-245-P 1/8" 358

Concrete floor to exterior gypsum curtain wall with 2 hr 8" 7.5% CP 672 CEJ-259-P 1/8" 360

EIFS façade (includes vision glass)

Concrete Floor to exterior gypsum curtain wall 2 hr 8" 7.5% CP 672 CEJ-261-P 1/8" 363

with stone façade (includes vision glass)

Concrete floor to exterior gypsum curtain wall with 2 hr 8" 7.5% CP 672 CEJ-263-P 1/8" 366

metal siding (includes vision glass)

Concrete floor to exterior gypsum curtain wall with 2 hr 0" 0% CP 672 CEJ-264-P 1/8" 369

EIFS façade (includes vision glass)

Concrete floor to exterior gypsum curtain wall with 2 hr 0" 0% CP 672 CEJ-265-P 1/8" 372

metal siding (includes vision glass)

Concrete floor to glass or aluminum spandrel with 3 hr 8" 11.25% & 5% CP 672 CEJ-307-P 1/8" 374

aluminum framing

Concrete floor to glass or aluminum spandrel with 3 hr 8" 11.25% & 5% CP 672 CEJ-308-P 1/8" 377

I-shaped aluminum framing

Concrete floor to glass spandrel with aluminum framing 1-3/4 hr 8" 11.25% & 5% CP 672 CEJ-309-P 1/8" 380

Concrete floor to glass spandrel with I-shaped 1-3/4 hr 8" 11.25% & 5% CP 672 CEJ-310-P 1/8" 383

aluminum framing

Concrete floor to exterior gypsum curtain wall with 2-3/4 hr 6" 8.3% & 5% CP 672 CEJ-314-P 1/8" 386

brick façade (includes vision glass)


cementitious finish (includes vision glass)


plaster finish (includes vision glass)

GFRC panels with steel framing 2 hr 8" 9.5% CP 672 CEJ-400-P 1/8" 392

Gypsum exterior with various façades with steel framing 2 hr 9" 0% CP 672 CEJ-421-P 1/8" 394

Tilt-up concrete curtain wall panel 2 hr 6" 5% CP 604 CW-D-1003 1/4" 398

Concrete floor to glass, aluminum, or granite spandrel 2 hr 8" 5% CP 604 CW-D-2026 1/4" 400

with aluminum framing

Concrete floor to glass, aluminum, or granite spandrel 2 hr 8" 5% CP 672 CW-D-2027 1/8" 403

with aluminum framing

Glass, aluminum or granite spandrel with aluminum 2 hr 4" 5% CP 672 CW-D-2046 1/8" 406

framing

Most Common Systems — TP

Chap

ter

Tab

sC

hap

ter

Tab

sC

hap

ter

Tab

sThro

ug

h-P

ene

tratio

nC

hap

ter

Tab

sC

hap

ter

Tab

s



Most Common Systems for Through Penetrations

Concrete Floor/Wall or Block WallDescription FS ONE CP 606 CP 604 CP 680-P CP 680-MBlank Opening F-A-0005 (159)

F-A-0014 (161) F-A-0014 (161)Metal Pipe C-AJ-1291 (68) C-AJ-1149 (65) C-AJ-1149 (65) F-A-1016 (162) F-A-1016 (162)

C-AJ-1226 (67) C-AJ-1435 (75) C-AJ-1421 (73) F-A-1017 (164) F-A-1017 (164)C-AJ-1421 (73) C-AJ-1453 (76) C-AJ-1425 (74)W-J-1067 (239) W-J-1124 (242)

Plastic Pipe C-AJ-2567* (100) F-A-2053 (171)F-A-2054 (172)F-A-2066 (175)F-A-2103 (182)

Cable Bundle C-AJ-3180 (102) C-AJ-3181 (103) C-AJ-3193 (104) F-A-3007 (187) F-A-3007 (187)C-AJ-3095 (101) W-J-3060 (252) F-A-8012 (198) F-A-3033 (189) F-A-3033 (189)W-J-3060 (252)

Metal Pipe with Glass-fiber Insulation C-AJ-5091 (118) C-AJ-5048 (115) C-AJ-5048 (115) F-A-5017 (193) F-A-5017 (193)C-AJ-5096 (119) F-A-8012 (198)W-J-5042 (264) F-A-5036 (196)

Metal Pipe with AB/PVC Insulation C-AJ-5090 (117) F-A-5032 (195) F-A-5015 (191) F-A-5015 (191)C-AJ-5198 (120) F-A-8012 (198)W-J-5041 (263)

Sheet Metal Duct (Rectangular) C-AJ-7051 (127) C-AJ-7051 (127) C-AJ-7046 (126)C-AJ-7111 (130)

Sheet Metal Duct (Round) C-AJ-7084 (128) C-AJ-7084 (128) C-AJ-7084 (128)W-J-7022 (266) W-J-7022 (266)

Multiple Penetrants C-AJ-8099 (137) F-A-8012 (198) F-A-1022 (166) F-A-1022 (166)C-AJ-8143 (142) F-A-5032 (195) F-A-1023 (167) F-A-1023 (167)

F-A-1066 (168) F-A-1066 (168)F-A-8016 (200) F-A-8016 (200)F-A-2103 (182)

Gypsum WallsDescription FS ONE CP 606Metal pipe W-L-1054 (276) W-L-1297 (282)Plastic Pipe W-L-2128* (289)Cable Bundle W-L-3065 (302) W-L-3065 (302)Metal Pipe with Glass-fiber Insulation W-L-5029 (324) W-L-5257 (332)Metal Pipe with AB/PVC Insulation W-L-5028 (323)Sheet Metal Duct (Rectangular) W-L-7155 (339) W-L-7155 (339)Sheet Metal Duct (Round) W-L-7042 (334) W-L-7042 (334)Multiple Penetrants W-L- 8065 (350)

W-L- 8071 (352)

Wood FloorsDescription FS ONE CP 606Metal pipe F-C-1009 (205) F-C-1009 (205)

F-C-1059 (206) F-C-1106 (207)Plastic Pipe F-C-2160* (210)Cable Bundle F-C-3012 (216) F-C-3074 (218)

F-C-3044 (217)Metal Pipe with Glass-fiber Insulation F-C-5036 (220) F-C-5066 (223)Metal Pipe with AB/PVC Insulation F-C-5004 (219) F-C-5065 (222)

F-C-5037 (221) -Sheet Metal Duct (Round) F-C-7013 (224) F-C-7025 (225)HVAC Line Set F-C-8026 (226) F-C-8032 (227)

Hollow Core FloorsDescription FS ONEMetal Pipe C-AJ-1184 (66)

C-BJ-1046 (150)Cable Bundle C-BJ-3024 (155)Metal Pipe with Glass-fiber Insulation C-BJ-5013 (156)

Gypsum Shaft WallsDescription FS ONEMetal Pipe W-L-1206 (278)

W-L-1380 (283)Cable Bundle W-L-3161 (308)Metal Pipe with Glass-fiber Insulation W-L-5244 (330)Metal Pipe with AB/PVC Insulation W-L-5143 (327)

Number in parenthesis refers to page number*Maximum 2" diameter

Most Common Systems — Joint




59

Chap

ter T

ab

sC

hap

ter T

ab

sC

hap

ter T

ab

sThro

ug

h-P

ene

tratio

nC

hap

ter T

ab

sC

hap

ter T

ab

s

Most Common Systems for Construction Joints

Gypsum WallsDescription CP 672 CP 606Perpendicular to Metal Deck HW-D-0042 (417) HW-D-0045 (419)

HW-D-0087 (422)HW-D-0292 (442)

Parallel to Metal Deck HW-D-0049 (420) HW-D-0184 (428)HW-D-0089 (424)

Flat Concrete HW-D-0106 (426) HW-D-0209 (429)Cut to Profile HW-D-0324 (444)Shaft wall to flat concrete HW-D-0342 (445)

Concrete or Block WallsDescription CP 672 CP 606Perpendicular to Metal Deck HW-D-1037 (451) HW-D-0081 (421)Parallel to Metal Deck HW-D-0181 (427) HW-D-0081 (421)Flat Concrete HW-D-1058 (453) HW-D-0268 (439)

HW-D-1009 (450)

Curtain Wall SystemsDescription of Wall CP 672 CP 604Glass spandrel with aluminum CW-D-2027 (403) CW-D-2026 (400)framing CEJ 307P (374)

CEJ 127P (356)Aluminum panel with aluminum CW-D-2027 (403) CW-D-2026 (400)framing CEJ 307P (374) CEJ 309P (380)Granite panel with aluminum framing CW-D-2027 (403) CW-D-2026 (400)Concrete Panel with steel framing CEJ 245P (358)Gypsum Exterior with EIFS CEJ 316P (390)

CEJ 421P (394)Gypsum Exterior with Stucco CEJ 315P (388)

CEJ 421P (394)Gypsum Exterior with Stone CEJ 261P (363)

CEJ 421P (394)Gypsum Exterior with Brick CEJ 314P (386)

CEJ 421P (394)Gypsum Exterior with Metal Siding CEJ 263P (366)

CEJ 421P (394)

Number in parenthesis refers to page number

System Details

Chap

ter

Tab

sC

hap

ter

Tab

sThro

ug

h-P

ene

tratio

nC

hap

ter

Tab

sC

hap

ter

Tab

s

