high-pressure pumps - series hp49 - andritz group · 3 description vertical, multistage...
TRANSCRIPT
www.andritz.com/pumps
High-pressure pumpsSeries HP55
3
DescriptionVertical, multistage high-pressure pump in sectional construction
with opposed suction and discharge branch of same nominal
width (in-line-execution).
Pumping mediaClean, fluid pumping media without abrasive, solid or long-fibre
constituents. The pump materials may not be attacked chemically
or mechanically.
Application range � Water procurement
- from surface water � Water treatment
- industrial circuits
- process technology
- potable water � Water supply
- industrial/domestic
- boiler feeding/condensation delivery
- irrigation
- booster � Water raising
- industrial/domestic
- drainage
Operating range
Nominal branch diameter DN 25-100
Capacity Q up to 140 m3/h
Head H up to 320 m
Operating pressure p up to 32 bar
Liquid temperature t -10°C up to +120°C
Speed n up to 3600 rpm
GeneralHP 65-135.1/5/2/S + 11/2
Nominal branch diameter [mm]
Nominal impeller diameter [mm]
Hydraulics ID
Nominal power P2 [kW]
Number of poles
Series
Number of stages
Arrangement
Number of trimmed impellers (Option)
Designation
Example
Shaft sealingThe pump is equipped with a maintenance-free mechanical seal.
Standard material is silicon carbide/silicon carbide EPDM. Other
mating of material is available upon request.
HP 25-80, HP 32-80, HP 40-95, HP 50-110
HP 65-135, HP 80-135, HP 100-145
4
ConnectionsType No. of stages Flange Connec-
tion50 Hz 60 Hzfrom to from to Oval Round
HP 25-80.12 23 2 15 Rp 1 1/4“2 37 2 25 DN25
HP 25-80.22 21 2 14 Rp 1 1/4“2 33 2 23 DN25
HP 32-80.12 21 2 14 Rp 1 1/4“2 33 2 23 DN32
HP 40-95.12 15 2 10 Rp 1 1/2“2 24 2 17 DN40
HP 50-110.11 10 1 7 Rp 2“1 17 1 12 DN50
HP 50-110.21 10 1 7 Rp 2“1 17 1 10 DN50
HP 65-135.1 1 13 1 8 DN65HP 80-135.1 1 13 1 7 DN80HP 100-145.1 1 8 1 5 DN100HP 100-145.2 1 6 1 4 DN100
Maximum permissible pump end pressureType Max. permissible pump end pressure in bar
Oval flange Round flangeHP 25-80.1 16 26HP 25-80.2 16 26HP 32-80.1 16 26HP 40-95.1 16 26HP 50-110.1 16 26HP 50-110.2 16 26HP 65-135.1 - 16/32HP 80-135.1 - 16/32HP 100-145.1 - 16/25HP 100-145.2 - 16/25
Pump end pressure = suction pressure + pump delivery head at
zero capacity.
Oval counter flanges
DN Dimensions (mm) Holes PND d1 k L b d2 N°
32 99 Rp 1 1/4“ 75 33 8 112 1640
130Rp 1 1/2“
10035
10 1350 Rp 2“ 39
Kit round counterflanges available on request; AISI 304
k
d2
d1
D
L
b
5
50Hz
Speed 2900 rpm
Selection chartThis chart allows a provisional selection of the pump type most
suitable for a given set of operating conditions. In certain cases
it may be possible to use the next smaller pump type and this
possibility should be included in the final selection. For an exact
pump selection our individual characteristic curves as well as our
pump selection software WinPump are available.
60Hz
Speed 3500 rpm
1000800
400
300
200
10080
605040
30
20
108
654
3
600500400
300
200
10080
605040
30
20
10
4 5 6 8 10 20 30 40 50 60 80 100 200 300 400 500 600 800
0.7 0.8 0.9 1 2 3 4 5 6 7 8 9 10 20 30 40 50 60 70 80 90 100 200
U.S. gpm
(m3/h)
m ft
1000800
400
300
200
10080
605040
30
20
108
654
3
600500400
300
200
10080
605040
30
20
10
4 5 6 8 10 20 30 40 50 60 80 100 200 300 400 500 600 800
0.7 0.8 0.9 1 2 3 4 5 6 7 8 9 10 20 30 40 50 60 70 80 90 100 200
U.S. gpm
(m3/h)
m ft
HP
25-
80.1
HP
25-
80.2
HP
32-
80.1
HP
40-
95.1
HP
50-
110.
1
HP
50-
110.
2
HP
65-
135.
1
HP
80-
135.
1
HP
100
-145
.1
HP
100
-145
.2
HP
25-
80.1
HP
25-
80.2
HP
32-
80.1
HP
40-
95.1
HP
50-
110.
1
HP
50-
110.
2
HP
65-
135.
1
HP
80-
135.
1
HP
100
-145
.1
HP
100
-145
.2
6
MotorsFrequency 50 HzFeatures
� Standard voltage up to 3kW 230/400V, 400/690V from 4kW and above � Temperature class F � Enclosure IP55 � Max. ambient temperature 40°C � Design B14 up to 4kW, design B5 from 5,5kW and above � Motors from 18,5kW are equipped with thermistors (PTC) � Multi-mount construction for an easy change of terminal box position � Terminal box rotates by 90° to allow cable entry from any direction � Easy-to-change flanges with over-sized and smaller-sized dimensions � Motors conforming to the higher efficiency standards for Europe, North America and Australia
Noise levelsThe noise values listed below refer to 50Hz
at rated voltage with a tolerance of up to
+ 3 dB(A). For 60Hz supply values are 3-5
dB(A) higher. Sound pressure level LpA and
sound power level LWA for three-phase
single-speed motors with dimensions and
output ratings to IEC 60072.
Frame size
2 poleLWA LpA
56 57 4863 58 4971 61 5280 72 6090 74 62
100 78 66112 80 68132 81 72160 87 74180 90 77200 91 78225 92 80
Power Class Size Design IN [A] IA/IN Speed η cos φ MN MA/MN Weight
kW ∆ 230V Y 400V ∆ 400V Y 690V [rpm] [%] [Nm] [kg]
0,37 IE2 71 B14 1,7 1,0 - - 4,7 2820 70,0 0,78 1,3 3,6 5,8
0,55 IE2 71 B14 2,6 1,5 - - 4,8 2830 71,0 0,77 1,9 3,2 6,2
0,75 IE3 80 B14 2,9 1,7 - - 8,9 2910 82,0 0,78 2,5 4,7 9,5
1,1 IE3 80 B14 4,2 2,4 - - 9,3 2870 82,7 0,76 3,7 5,0 11,1
1,5 IE3 90 B14 5,2 3,0 - - 8,4 2875 84,2 0,85 5,0 3,6 14,0
2,2 IE3 90 B14 8,0 4,6 - - 9,2 2880 86,5 0,82 7,3 4,0 16,0
3 IE3 100 B14 9,7 5,6 - - 8,8 2900 87,1 0,89 9,9 5,5 22,8
4 IE3 112 B14 - - 8,0 4,6 10,7 2900 88,1 0,83 13,0 5,1 26,5
5,5 IE3 132 B5 - - 10,2 5,9 11,2 2935 89,2 0,87 17,9 4,2 33,6
7,5 IE3 132 B5 - - 14,4 8,3 10,4 2930 90,1 0,84 24,5 4,5 36
11 IE3 160 B5 - - 19,9 11,5 9,7 2935 91,2 0,89 35,8 4,4 62
15 IE3 160 B5 - - 26,8 15,5 9,6 2915 91,9 0,88 49,2 3,7 68
18,5 IE3 160 B5 - - 33,0 19,1 10,7 2950 92,4 0,88 59,9 4,6 104
22 IE3 180 B5 - - 39,4 22,8 10,4 2950 92,7 0,87 71,3 4,5 106
30 IE3 200 B5 - - 52,7 30,5 6,7 2925 93,3 0,88 97,9 2,4 276
37 IE3 200 B5 - - 63,3 36,6 6,3 2930 93,7 0,90 120,6 2,3 283
45 IE3 225 B5 - - 78,5 45,4 6,9 2930 94,0 0,88 146,7 2,3 370
7
MotorsFrequency 60 Hz
Noise levelsThe noise values listed below refer to 50Hz
at rated voltage with a tolerance of up to
+ 3 dB(A). For 60Hz supply values are 3-5
dB(A) higher. Sound pressure level LpA and
sound power level LWA for three-phase
single-speed motors with dimensions and
output ratings to IEC 60072.
Frame size
2 poleLWA LpA
56 57 4863 58 4971 61 5280 72 6090 74 62
100 78 66112 80 68132 81 72160 87 74180 90 77200 91 78225 92 80
Power Class Size Design IN [A] IA/IN Speed η cos φ MN MA/MN Weight
kW ∆ 220V Y 380V [rpm] [%] [Nm] [kg]
0,37 IE2 71 B14 1,8 1,0 4,2 3400 72,0 0,75 1,1 2,3 5,8
0,55 IE2 71 B14 3,0 1,7 4,6 3450 73,0 0,77 1,5 2,5 6,2
0,75 IE3 80 B14 3,3 1,9 8,9 3500 77,0 0,78 2,1 4,7 9,5
1,1 IE3 80 B14 4,7 2,7 9,3 3480 84,0 0,78 3,0 5,0 11,1
1,5 IE3 90 B14 5,9 3,4 8,4 3515 85,5 0,80 4,1 3,6 14,0
2,2 IE3 90 B14 8,0 4,6 9,2 3480 86,5 0,84 6,0 4,0 16,0
3 IE3 100 B14 10,4 6,0 8,8 3515 88,1 0,88 8,2 5,5 22,8
4 IE3 112 B14 13,2 7,6 10,9 3520 89,0 0,89 10,9 6,1 26,5
5,5 IE3 132 B5 18,2 10,5 9,6 3510 89,5 0,89 15,0 3,6 27,4
7,5 IE3 132 B5 25,1 14,5 10,4 3520 90,2 0,87 20,3 4,5 36
11 IE3 160 B5 34,3 19,8 9,7 3520 91,0 0,92 29,8 4,4 59
15 IE3 160 B5 46,4 26,8 9,6 3520 91,0 0,92 40,7 3,7 68
18,5 IE3 160 B5 62,0 35,6 10,7 3540 91,7 0,86 49,9 4,6 104
22 IE3 180 B5 71,7 41,7 10,4 3530 91,7 0,88 59,5 4,5 104
30 IE3 200 B5 94,0 54,0 9,0 3565 94,1 0,90 80,8 2,8 239
37 IE3 200 B5 114,0 66,0 8,5 3560 93,9 0,91 99,0 2,6 249
45 IE3 225 B5 137,0 79,0 7,8 3570 95,0 0,91 120,0 2,5 322
Features � Standard voltage 220/380V � Temperature class F � Enclosure IP55 � Max. ambient temperature 40°C � Design B14 up to 4kW, design B5 from 5,5kW and above � Motors from 18,5kW are equipped with thermistors (PTC) � Multi-mount construction for an easy change of terminal box position � Terminal box rotates by 90° to allow cable entry from any direction � Easy-to-change flanges with over-sized and smaller-sized dimensions � Motors conforming to the higher efficiency standards for Europe, North America and Australia
8
MaterialsHP 25-80, HP 32-80, HP 40-95The standard materials of construction for the main pump components are shown below together with details of alternative materials
available. We reserve the right to change material specification without notice.
Pos. Description Material Material combination
AISI 304 AISI 316
ASTM/AISI DIN / EN ASTM/AISI DIN / EN
10.00 Pump casing Stainless Steel CF 8 / AISI 304 1.4308 CF 8M / AISI 316 1.4408
10.02 Filling and draining plug Stainless Steel AISI 304 1.4301 AISI 316 1.4401
10.06 Upper flange Stainless Steel AISI 304 1.4301 AISI 316 1.4401
20.00 Outer Case Stainless Steel AISI 304 1.4301 AISI 316 1.4401
20.01 Mechanical seal housing Stainless Steel AISI 304 1.4301 AISI 316 1.4401
20.05 Filling plugs Stainless Steel AISI 304 1.4301 AISI 316 1.4401
30.00 Pump shaft Stainless Steel AISI 304 1.4301 AISI 316 1.4401
30.01 Kit Mechanical sealSIC/SIC, EPDM, Stainless Steel
- - - -
30.02 Mechanical seal fastening kit Stainless Steel AISI 304 1.4301 AISI 316 1.4401
30.03 Kit O-rings EPDM - - - -
40.00 Stage housing and diffuser Stainless Steel AISI 304 1.4301 AISI 316 1.4401
40.01 Stage Centering outlet Stainless Steel AISI 304 1.4301 AISI 316 1.4401
40.02 Floating neck ring PPS - - - -
40.03 Initial stage housing Stainless Steel AISI 304 1.4301 AISI 316 1.4401
40.04 Last Stage with diffuser Stainless Steel AISI 304 1.4301 AISI 316 1.4401
40.05 Stage Centering inlet Stainless Steel AISI 304 1.4301 AISI 316 1.4401
40.06Stage housing and diffuser with bearing
Stainless Steel / Tungsten Carbide
AISI 304 1.4301 AISI 316 1.4401
50.00 Impeller Stainless Steel AISI 304 1.4301 AISI 316 1.4401
50.01 Impeller spacer Stainless Steel AISI 304 1.4301 AISI 316 1.4401
50.02 Intermediary sleeve Tungsten Carbide - - - -
50.03 Intermediary sleeve spacer Stainless Steel AISI 304 1.4301 AISI 316 1.4401
9
MaterialsHP 50-110The standard materials of construction for the main pump components are shown below together with details of alternative materials
available. We reserve the right to change material specification without notice.
Pos. Description Material Material combination
AISI 304 AISI 316
ASTM/AISI DIN / EN ASTM/AISI DIN / EN
10.00 Pump casing Stainless Steel CF 8 / AISI 304 1.4301 CF 8M / AISI 316 1.4408
10.02 Filling and draining plug Stainless Steel AISI 304 1.4301 AISI 316 1.4401
10.06 Upper Flange Stainless Steel AISI 304 1.4301 CF 8M / AISI 316 1.4408
20.00 Outer Case Stainless Steel AISI 304 1.4301 AISI 316 1.4401
20.01 Mechanical seal housing Stainless Steel AISI 304 1.4301 CF 8M / AISI 316 1.4408 / 1.4401
20.05 Filling plugs Stainless Steel AISI 304 1.4301 AISI 316 1.4401
30.00 Pump shaft Stainless Steel AISI 304 1.4301 AISI 316 1.4401
30.01 Kit Mechanical sealSIC/SIC, EPDM, Stainless Steel
- - - -
30.02 Mechanical seal fastening kit Stainless Steel AISI 304 1.4301 AISI 316 1.4401
30.03 Kit O-rings EPDM - - - -
40.00 Stage housing and diffuser Stainless Steel AISI 304 1.4301 AISI 316 1.4401
40.01 Stage Centering outlet Stainless Steel AISI 304 1.4301 AISI 316 1.4401
40.02 Floating neck ring PPS - - - -
40.03 Initial stage housing Stainless Steel AISI 304 1.4301 AISI 316 1.4401
40.04 Last Stage with diffuser Stainless Steel AISI 304 1.4301 AISI 316 1.4401
40.06Stage housing and diffuser with bearing
Stainless Steel / Tungsten carbide
AISI 304 1.4301 AISI 316 1.4401
50.00 Impeller Stainless Steel AISI 304 1.4301 AISI 316 1.4401
50.01 Impeller spacer Stainless Steel AISI 304 1.4301 AISI 316 1.4401
50.02 Intermediary sleeve Tungsten Carbide - - - -
50.03 Intermediary sleeve spacer Stainless Steel AISI 304 1.4301 AISI 316 1.4401
10
MaterialsHP 65-135, HP 80-135The standard materials of construction for the main pump components are shown below together with details of alternative materials
available. We reserve the right to change material specification without notice.
Pos. Description Material Material combination
AISI 304 AISI 316
ASTM/AISI DIN / EN ASTM/AISI DIN / EN
10.00 Pump casing Cast Iron / Stainless Steel A48 Class 35 GJL-250 CF 8M / AISI 316 1.4408
10.02 Draining plug Stainless Steel AISI 304 1.4301 AISI 316 1.4401
10.06 Upper Flange Stainless Steel CF 8 / AISI 304 1.4308 CF 8M / AISI 316 1.4408
20.00 Outer Case Stainless Steel AISI 304 1.4301 AISI 316 1.4401
20.01 Mechanical seal housing Stainless Steel CF 8 / AISI 304 1.4308 CF 8M / AISI 316 1.4408
20.05 Filling plugs Stainless Steel AISI 304 1.4301 AISI 316 1.4401
30.00 Pump shaft Stainless Steel AISI 431 1.4057 AISI 329 1.4460
30.01 Kit Mechanical sealSIC/SIC, EPDM, Stainless Steel
- - - -
30.02 Mechanical seal fastening kit Stainless Steel AISI 316 1.4401 AISI 316 1.4401
30.03 Kit O-rings EPDM - - - -
40.00 Stage housing and diffuser Stainless Steel / Graphite AISI 304 1.4301 AISI 316 1.4401
40.02 Floating neck ring PTFE - - - -
40.05 Stage Centering inlet Stainless Steel AISI 316 1.4401 AISI 316 1.4401
40.06Stage housing and diffuser with bearing
Stainless Steel AISI 304 1.4301 AISI 316 1.4401
40.07 Flange clamping neck ring Stainless Steel AISI 304 1.4301 AISI 316 1.4401
40.08 Spring ring Stainless Steel AISI 316 1.4401 AISI 316 1.4401
50.00 Impeller Stainless Steel AISI 304 1.4301 AISI 316 1.4401
51.01 Split cone Stainless Steel AISI 304 1.4301 AISI 316 1.4401
51.02 Intermediary sleeve nutStainless Steel / Tungsten Carbide
AISI 316 1.4401 AISI 316 1.4401
51.03 Journal sleeveStainless Steel / Tungsten Carbide
AISI 316 1.4401 AISI 316 1.4401
51.04 Split cone nut Stainless Steel AISI 304 1.4301 AISI 316 1.4401
51.05Intermediate impeller with screw
Stainless Steel AISI 304 1.4301 AISI 316 1.4401
11
MaterialsHP 100-145The standard materials of construction for the main pump components are shown below together with details of alternative materials
available. We reserve the right to change material specification without notice.
Pos. Description Material Material combination
AISI 304 AISI 316
ASTM/AISI DIN / EN ASTM/AISI DIN / EN
10.00 Pump casing Cast Iron / Stainless Steel A48 Class 35 GJL-250 CF 8M / AISI 316 1.4408
10.02 Draining plug Stainless Steel AISI 304 1.4301 AISI 316 1.4401
10.06 Upper Flange Stainless Steel CF 8 / AISI 304 1.4308 CF 8M / AISI 316 1.4408
20.00 Outer Case Stainless Steel AISI 304 1.4301 AISI 316 1.4401
20.01 Mechanical seal housing Stainless Steel CF 8 / AISI 304 1.4308 CF 8M / AISI 316 1.4408
20.05 Filling plugs Stainless Steel AISI 304 1.4301 AISI 316 1.4401
30.00 Pump shaft Stainless Steel AISI 431 1.4057 AISI 329 1.4460
30.01 Kit Mechanical sealSIC/SIC, EPDM, Stainless Steel
- - - -
30.02 Mechanical seal fastening kit Stainless Steel AISI 316 1.4401 AISI 316 1.4401
30.03 Kit O-rings EPDM - - - -
40.00 Stage housing and diffuser Stainless Steel / Graphite AISI 304 1.4301 AISI 316 1.4401
40.01 Stage Centering outlet Stainless Steel CF 8 / AISI 304 1.4308 CF 8M / AISI 316 1.4408
40.02 Floating neck ring PTFE - - - -
40.05 Stage Centering inlet Stainless Steel AISI 316 1.4401 AISI 316 1.4401
40.06Stage housing and diffuser with bearing
Stainless Steel AISI 304 1.4301 AISI 316 1.4401
40.07 Flange clamping neck ring Stainless Steel AISI 304 1.4301 AISI 316 1.4401
40.08 Spring ring Stainless Steel AISI 316 1.4401 AISI 316 1.4401
50.00 Impeller Stainless Steel AISI 304 1.4301 AISI 316 1.4401
51.01 Split cone Stainless Steel AISI 304 1.4301 AISI 316 1.4401
51.02 Intermediary sleeve nutStainless Steel / Tungsten Carbide
AISI 316 1.4401 AISI 316 1.4401
51.03 Journal sleeveStainless Steel / Tungsten Carbide
AISI 316 1.4401 AISI 316 1.4401
51.04 Split cone nut Stainless Steel AISI 304 1.4301 AISI 316 1.4401
51.05 Intermediate impeller with screw Stainless Steel AISI 304 1.4301 AISI 316 1.4401
12
Performance curveType HP 25-80.1
Speed 2900 rpm
0
20
40
60
0.000
40
80
120
160
200
240
280
320
360
10
20
30
40
50
60
70
80
90
100
110
0 10 20 30 40 50
0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2
ft
ft16
12
8
0
4
5
4
3
2
1
00.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2
0 2 4 6 8 10 12 14
0 10 20 30 40 50
0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Q/H
ETA
NPSH
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
MEI ≥ 0,70
13
50Hz
Dimensions and weightsType HP 25-80.1
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 25-80.1/2 0,37 71 312,5 527,5 287,5 502,5 215 142 170 112 15 20,8HP 25-80.1/3 0,37 71 335 550 310 525 215 142 170 112 15 20,8HP 25-80.1/4 0,37 71 357,5 572,5 332,5 547,5 215 142 170 112 15,5 21,3HP 25-80.1/5 0,37 71 380 595 355 570 215 142 170 112 16 21,8HP 25-80.1/6 0,37 71 402,5 617,5 377,5 592,5 215 142 170 112 16,5 22,3HP 25-80.1/7 0,37 71 425 640 400 615 215 142 170 112 17 22,8HP 25-80.1/8 0,55 71 447,5 662,5 422,5 637,5 215 142 170 112 17,5 23,7HP 25-80.1/9 0,55 71 470 685 445 660 215 142 170 112 18 24,2HP 25-80.1/10 0,55 71 492,5 707,5 467,5 682,5 215 142 170 112 18,5 24,7HP 25-80.1/11 0,55 71 515 730 490 705 215 142 170 112 19 25,2HP 25-80.1/12 0,75 80 537,5 769,5 512,5 744,5 232 160 170 129 19,5 29HP 25-80.1/13 0,75 80 560 792 535 767 232 160 170 129 20 29,5HP 25-80.1/14 0,75 80 582,5 814,5 557,5 789,5 232 160 170 129 20,5 30HP 25-80.1/15 0,75 80 605 837 580 812 232 160 170 129 21 30,5
D2
25
75
L1L2
L1+L
2
M
D1
180
210
100
150
N°4xØ13
250
25
50
L3
L3+L
2
160
Ø115
Ø85
N°4x
Ø14
Rp 1DN 25
75
N°2 Screw/NutM10
Rp 1¼DN 32
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional ac-cessories, including bolts and joints).
Round flange
Round flanges on body type PN25: the pump is supplied without coun-terflanges (Optional accessories, including bolts and joints).
Available from 2 to 23 stages
14
Performance curveType HP 25-80.1
Speed 2900 rpm
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
0
20
40
60
0.000
100
50
200
150
300
250
400
350
500
450
600
550
700
650
850
800
750
900
20
60
40
80
100
140
120
160
180
200
240
220
260
280
0 10 20 30 40 50
0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2
ft
ft0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2
16
12
8
0
4
5
4
3
2
1
00.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2
0 2 4 6 8 10 12 14
0 10 20 30 40 50
37
34
32
30
27
25
22
23
19
17
ETA
Q/H
NPSH
MEI ≥ 0,70
15
50Hz
Dimensions and weightsType HP 25-80.1
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 25-80.1/17 1,1 80 650 882 625 857 232 160 170 129 22 33,1HP 25-80.1/19 1,1 80 695 927 670 902 232 160 170 129 22,5 33,6HP 25-80.1/22 1,1 80 762,5 994,5 737,5 969,5 232 160 170 129 24 35,1HP 25-80.1/23 1,5 90 795 1062 770 1037 267 180 170 138 25 39HP 25-80.1/25 1,5 90 840 1107 - - 267 180 170 138 26 40HP 25-80.1/27 1,5 90 885 1152 - - 267 180 170 138 27 41HP 25-80.1/30 1,5 90 952,5 1219,5 - - 267 180 170 138 28,5 42,5HP 25-80.1/32 2,2 90 997,5 1264,5 - - 267 180 170 138 29 45HP 25-80.1/34 2,2 90 1042,5 1309,5 - - 267 180 170 138 30 46HP 25-80.1/37 2,2 90 1110 1377 - - 267 180 170 138 31,5 47,5
D2
25
75
L1L2
L1+L
2
M
D1
180
210
100
150
N°4xØ13
250
25
50
L3
L3+L
2
160
Ø115
Ø85
N°4x
Ø14
Rp 1DN 25
75
N°2 Screw/NutM10
Rp 1¼DN 32
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional ac-cessories, including bolts and joints).
Round flange
Round flanges on body type PN25: the pump is supplied without coun-terflanges (Optional accessories, including bolts and joints).
Available from 2 to 23 stages
16
Performance curveType HP 25-80.2
Speed 2900 rpm
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
MEI ≥ 0,70
ft
ft
0.0 0.8 1.6 2.4 3.2 4.0 4.8
0.0 0.8 1.6 2.4 3.2 4.0 4.80
20
40
60
0
20
40
60
80
100
120
0 10 20 30 5040 60 70 80
0
40
80
120
200
240
280
320
360
400
160
0
4
12
16
8
0
1
2
3
4
5
0.0 0.8 1.6 2.4 3.2 4.0 4.8
0 10 20 30 5040 60 70 80
0 4 8 12 16 20
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
ETA
Q/H
NPSH
17
50Hz
Dimensions and weightsType HP 25-80.2
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 25-80.2/2 0,37 71 312,5 527,5 287,5 502,5 215 142 170 112 15 20,8HP 25-80.2/3 0,37 71 335 550 310 525 215 142 170 112 15 20,8HP 25-80.2/4 0,37 71 357,5 572,5 332,5 547,5 215 142 170 112 15,5 21,3HP 25-80.2/5 0,55 71 380 595 355 570 215 142 170 112 16 22,2HP 25-80.2/6 0,55 71 402,5 617,5 377,5 592,5 215 142 170 112 16,5 22,7HP 25-80.2/7 0,75 80 425 657 400 632 232 160 170 129 17 26,5HP 25-80.2/8 0,75 80 447,5 679,5 422,5 654,5 232 160 170 129 17,5 27HP 25-80.2/9 0,75 80 470 702 445 677 232 160 170 129 18 27,5HP 25-80.2/10 1,1 80 492,5 724,5 467,5 699,5 232 160 170 129 18,5 29,6HP 25-80.2/11 1,1 80 515 747 490 722 232 160 170 129 19 30,1HP 25-80.2/12 1,1 80 537,5 769,5 512,5 744,5 232 160 170 129 19,5 30,6HP 25-80.2/13 1,1 80 560 792 535 767 232 160 170 129 20 31,1HP 25-80.2/14 1,5 90 592,5 859,5 567,5 834,5 267 180 170 138 21 35HP 25-80.2/15 1,5 90 615 882 590 857 267 180 170 138 21,5 35,5HP 25-80.2/16 1,5 90 637,5 904,5 612,5 879,5 267 180 170 138 22 36
D2
25
75
L1L2
L1+L
2
M
D1
180
210
100
150
N°4xØ13
250
25
50
L3
L3+L
2
160
Ø115
Ø85
N°4x
Ø14
Rp 1DN 25
75
N°2 Screw/NutM10
Rp 1¼DN 32
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional ac-cessories, including bolts and joints).
Round flange
Round flanges on body type PN25: the pump is supplied without coun-terflanges (Optional accessories, including bolts and joints).
Available from 2 to 21 stages
18
Performance curveType HP 25-80.2
Speed 2900 rpm
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
MEI ≥ 0,70
ft
ft0.0 0.8 1.6 2.4 3.2 4.0 4.8
0.0 0.8 1.6 2.4 3.2 4.0 4.8
0
20
40
60
40
60
80
100
120
140
160
180
220
240
200
260
0 10 20 30 5040 60 70 80
150
200
250
350
300
450
500
550
600
650
700
750
800
850
400
0
4
12
16
8
0
1
2
3
4
5
0.0 0.8 1.6 2.4 3.2 4.0 4.8
0 10 20 30 5040 60 70 80
0 4 8 12 16 20
33
31
29
27
25
23
21
19
18
17
ETA
Q/H
NPSH
19
50Hz
Dimensions and weightsType HP 25-80.2
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 25-80.2/17 1,5 90 660 927 635 902 267 180 170 138 22,5 36,5HP 25-80.2/18 2,2 90 682,5 949,5 657,5 924,5 267 180 170 138 23 39HP 25-80.2/19 2,2 90 705 972 680 947 267 180 170 138 23,5 39,5HP 25-80.2/21 2,2 90 750 1017 725 992 267 180 170 138 24 40HP 25-80.2/23 2,2 90 795 1062 - - 267 180 170 138 25 41HP 25-80.2/25 2,2 90 840 1107 - - 267 180 170 138 26 42HP 25-80.2/27 3 100 895 1185 - - 290 180 170 138 27,5 45,5HP 25-80.2/29 3 100 940 1230 - - 290 180 170 138 28,5 46,5HP 25-80.2/31 3 100 985 1275 - - 290 180 170 138 29,5 47,5HP 25-80.2/33 3 100 1030 1320 - - 290 180 170 138 30,5 48,5
D2
25
75
L1L2
L1+L
2
M
D1
180
210
100
150
N°4xØ13
250
25
50
L3
L3+L
2
160
Ø115
Ø85
N°4x
Ø14
Rp 1DN 25
75
N°2 Screw/NutM10
Rp 1¼DN 32
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional ac-cessories, including bolts and joints).
Round flange
Round flanges on body type PN25: the pump is supplied without coun-terflanges (Optional accessories, including bolts and joints).
Available from 2 to 21 stages
20
Performance curveType HP 32-80.1
Speed 2900 rpm
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
MEI ≥ 0,70
ft
ft
0.0 1 2 3 4 5 6 7 8 9
0
20
40
60
80
0 20 40 60 80 100 120 140
0
20
40
60
80
100
120
140
0
50
100
150
200
250
300
350
400
450
0
4
8
12
1645
3
2
1
0
0 4 8 12 16 20 24 28 32 36
0.0 1 2 3 4 5 6 7 8 9
0.0 1 2 3 4 5 6 7 8 9
0 20 40 60 80 100 120 140
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
ETA
Q/H
NPSH
21
50Hz
Dimensions and weightsType HP 32-80.1
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 32-80.1/2 0,37 71 319,5 534,5 294,5 509,5 215 142 170 112 15 20,8HP 32-80.1/3 0,37 71 345,5 560,5 320,5 535,5 215 142 170 112 15,5 21,3HP 32-80.1/4 0,55 71 371,5 586,5 346,5 561,5 215 142 170 112 16 22,2HP 32-80.1/5 0,75 80 397,5 629,5 372,5 604,5 232 160 170 129 16,5 26HP 32-80.1/6 0,75 80 423,5 655,5 398,5 630,5 232 160 170 129 17,5 27HP 32-80.1/7 1,1 80 449,5 681,5 424,5 656,5 232 160 170 129 18 29,1HP 32-80.1/8 1,1 80 475,5 707,5 450,5 682,5 232 160 170 129 18,5 29,6HP 32-80.1/9 1,1 80 501,5 733,5 476,5 708,5 232 160 170 129 19 30,1HP 32-80.1/10 1,5 90 537,5 804,5 512,5 779,5 267 180 170 138 20 34HP 32-80.1/11 1,5 90 563,5 830,5 538,5 805,5 267 180 170 138 20,5 34,5HP 32-80.1/12 1,5 90 589,5 856,5 564,5 831,5 267 180 170 138 21 35HP 32-80.1/13 1,5 90 615,5 882,5 590,5 857,5 267 180 170 138 21,5 35,5HP 32-80.1/14 2,2 90 641,5 908,5 616,5 883,5 267 180 170 138 22 38HP 32-80.1/15 2,2 90 667,5 934,5 642,5 909,5 267 180 170 138 22,5 38,5HP 32-80.1/16 2,2 90 693,5 960,5 668,5 935,5 267 180 170 138 23 39HP 32-80.1/17 2,2 90 719,5 986,5 694,5 961,5 267 180 170 138 23,5 39,5
D2
25
75
L1L2
L1+L
2
M
D1
180
210
100
150
N°4xØ13
250
25
50
L3
L3+L
2
160
Ø140
Ø100
N°4x
Ø18
Rp 1¼DN 32
75
N°2 Screw/NutM10
Rp 1¼DN 32
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional ac-cessories, including bolts and joints).
Round flange
Round flanges on body type PN25: the pump is supplied without coun-terflanges (Optional accessories, including bolts and joints).
Available from 2 to 21 stages
22
Performance curveType HP 32-80.1
Speed 2900 rpm
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
MEI ≥ 0,70
ft
ft0.0 1 2 3 4 5 6 7 8 9
0.0 1 2 3 4 5 6 7 8 9
0
20
40
60
80
0 20 40 60 80 100 120 140
40
60
80
100
120
140
160
180
200
220
240
260
280
150
200
250
300
350
400
450
500
550
650
600
700
750
800
850
900
0
4
8
12
16
4
5
3
2
1
0
0 4 8 12 16 20 24 28 32 36
0.0 1 2 3 4 5 6 7 8 9
0 20 40 60 80 100 120 140
18
20
19
21
23
25
28
30
33
ETA
Q/H
NPSH
23
50Hz
Dimensions and weightsType HP 32-80.1
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 32-80.1/18 2,2 90 745,5 1012,5 720,5 987,5 267 180 170 138 24 40HP 32-80.1/19 2,2 90 771,5 1038,5 746,5 1013,5 267 180 170 138 24,5 40,5HP 32-80.1/20 3 100 807,5 1097,5 782,5 1072,5 290 180 170 138 25,5 43,5HP 32-80.1/21 3 100 833,5 1123,5 808,5 1098,5 290 180 170 138 26 44HP 32-80.1/23 3 100 885,5 1175,5 - - 290 180 170 138 27 45HP 32-80.1/25 3 100 937,5 1227,5 - - 290 180 170 138 28,5 46,5HP 32-80.1/28 4 112 1015,5 1321,5 - - 306 196 170 145 30 56,5HP 32-80.1/30 4 112 1067,5 1373,5 - - 306 196 170 145 31 57,5HP 32-80.1/33 4 112 1145,5 1451,5 - - 306 196 170 145 32,5 59
D2
25
75
L1L2
L1+L
2
M
D1
180
210
100
150
N°4xØ13
250
25
50
L3
L3+L
2
160
Ø140
Ø100
N°4x
Ø18
Rp 1¼DN 32
75
N°2 Screw/NutM10
Rp 1¼DN 32
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional ac-cessories, including bolts and joints).
Round flange
Round flanges on body type PN25: the pump is supplied without coun-terflanges (Optional accessories, including bolts and joints).
Available from 2 to 21 stages
24
Performance curveType HP 40-95.1
Speed 2900 rpm
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
MEI ≥ 0,70
ft
ft
0
4
8
16
12 4
5
3
2
10
0.0 2 4 6 8 10 12 14 16
0
20
40
60
80
0 30 60 90 120 150 180 210 240
0.0
20
40
60
80
100
120
140
0
50
100
150
200
250
300
350
400
450
0 5 10 15 20 25 30 35 40 45 50 55 65 7060
0.0 2 4 6 8 10 12 14 16
0 30 60 90 120 150 180 210 240
0.0 2 4 6 8 10 12 14 16
5
2
3
4
7
6
8
9
10
11
13
12
ETA
Q/H
NPSH
25
50Hz
Dimensions and weightsType HP 40-95.1
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 40-95.1/2 0,75 80 347,5 579,5 347,5 579,5 232 160 170 129 17,5 27HP 40-95.1/3 1,1 80 377,5 609,5 377,5 609,5 232 160 170 129 18 29,1HP 40-95.1/4 1,5 90 417,5 684,5 417,5 684,5 267 180 170 138 19,5 33,5HP 40-95.1/5 1,5 90 447,5 714,5 447,5 714,5 267 180 170 138 20 34HP 40-95.1/6 2,2 90 477,5 744,5 477,5 744,5 267 180 170 138 20,5 36,5HP 40-95.1/7 2,2 90 507,5 774,5 507,5 774,5 267 180 170 138 21 37HP 40-95.1/8 3 100 547,5 837,5 547,5 837,5 290 180 170 138 22,5 40,5HP 40-95.1/9 3 100 577,5 867,5 577,5 867,5 290 180 170 138 23 41HP 40-95.1/10 4 112 607,5 913,5 607,5 913,5 306 196 170 145 24 50,5HP 40-95.1/11 4 112 637,5 943,5 637,5 943,5 306 196 170 145 24,5 51HP 40-95.1/12 4 112 667,5 973,5 667,5 973,5 306 196 170 145 25 51,5HP 40-95.1/13 4 112 697,5 1003,5 697,5 1003,5 306 196 170 145 26 52,5
27,5
80
L1L2
L1+L
2
M
D1
215
250
130
185
N°4xØ13
280
27,7
80
L3
L3+L
2
200
Ø150
Ø110
N°4x
Ø18
Rp 1½DN 40
100
N°2 Screw/NutM12
Rp 1½DN 40
D2
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional ac-cessories, including bolts and joints).
Round flange
Round flanges on body type PN25: the pump is supplied without coun-terflanges (Optional accessories, including bolts and joints).
Available from 2 to 15 stages
26
Performance curveType HP 40-95.1
Speed 2900 rpm
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
MEI ≥ 0,70
ft
ft
0
4
8
16
12 4
5
3
2
1
0
0
20
40
60
80
40
60
80
100
120
140
160
180
200
220
260
240
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
0.0 2 4 6 8 10 12 14 16
0 30 60 90 120 150 180 210 240
0 5 10 15 20 25 30 35 40 45 50 55 65 7060
0.0 2 4 6 8 10 12 14 16
0 30 60 90 120 150 180 210 240
0.0 2 4 6 8 10 12 14 16
15
17
19
23
24
21
ETA
Q/H
NPSH
27
50Hz
Dimensions and weightsType HP 40-95.1
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 40-95.1/15 5,5 132 933 1261 933 1261 328 225 300 161 46,5 80,1HP 40-95.1/17 5,5 132 993 1321 - - 328 225 300 161 48 81,6HP 40-95.1/19 7,5 132 1053 1403 - - 350 225 300 161 49 85HP 40-95.1/21 7,5 132 1113 1463 - - 350 225 300 161 50,5 86,5HP 40-95.1/23 7,5 132 1173 1523 - - 350 225 300 161 52 88HP 40-95.1/24 11 160 1223 1648 - - 425 248 350 198 55 114
27,5
80
L1L2
L1+L
2
M
D1
215
250
130
185
N°4xØ13
280
27,7
80
L3
L3+L
2
200
Ø150
Ø110
N°4x
Ø18
Rp 1½DN 40
100
N°2 Screw/NutM12
Rp 1½DN 40
D2
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional ac-cessories, including bolts and joints).
Round flange
Round flanges on body type PN25: the pump is supplied without coun-terflanges (Optional accessories, including bolts and joints).
Available from 2 to 15 stages
28
Performance curveType HP 50-110.1
Speed 2900 rpm
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
MEI ≥ 0,70
ft
ft
0123456
0 4 8 12 16 20 24 28
0
20
40
60
80
100
120
140
160
180
200
220
240
260
0
50
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
0 4 8 12 16 20 24 28
1618
1284
0
0 100 200 300 400
20304050607080
4 8 12 16 20 24 28
0
0
100 200 300 400
0 20 40 60 80 100 120
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
ETA
Q/H
NPSH
29
50Hz
Dimensions and weightsType HP 50-110.1
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional accesso-ries, including bolts and joints).Available from 1 to 10 stages
200
9026
,5
N° 2
x Ø
13
100L3
+ L
2L3
DN 50
DN 50
N°4 x Ø 13 130185
215
250
30026,5
90
L1L2
L1 +
L2
Ø 127
Ø 165
19N
° 4 x
Ø
Ø D1
M
D2
Round flange
Round flanges on body type PN25: the pump is supplied without counterflanges (Op-tional accessories, including bolts and joints).
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 50-110.1/1 1,1 80 405 637 405 637 232 160 170 129 23,5 35,5HP 50-110.1/2 2,2 90 415 682 415 682 267 180 170 138 25 41HP 50-110.1/3 3 100 473 740 473 740 267 180 170 138 27 45,7HP 50-110.1/4 4 112 521 827 521 827 306 196 170 145 28,5 51,3HP 50-110.1/5 4 112 569 875 569 875 306 196 170 145 30 52,8HP 50-110.1/6 5,5 132 804 1132 804 1132 328 225 300 161 52 86HP 50-110.1/7 5,5 132 852 1180 852 1180 328 225 300 161 53 87HP 50-110.1/8 7,5 132 900 1250 900 1250 350 225 300 161 54,5 90,5HP 50-110.1/9 7,5 132 948 1298 948 1298 350 225 300 161 56 92HP 50-110.1/10 11 160 1016 1441 1016 1441 425 248 350 198 60 118HP 50-110.1/11 11 160 1064 1489 - - 425 248 350 198 61,5 119,5HP 50-110.1/12 11 160 1112 1537 - - 425 248 350 198 63 121HP 50-110.1/13 11 160 1160 1585 - - 425 248 350 198 64,5 122,5HP 50-110.1/14 11 160 1208 1633 - - 425 248 350 198 66 124HP 50-110.1/15 15 160 1256 1732 - - 476 248 350 198 67 131HP 50-110.1/16 15 160 1304 1780 - - 476 248 350 198 68,5 132,5HP 50-110.1/17 15 160 1352 1828 - - 476 248 350 198 70 134
30
Performance curveType HP 50-110.2
Speed 2900 rpm
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
MEI ≥ 0,70
ft
ft
0123456
1618
1284
0
20304050607080
0 4 8 12 16 20 24 3228
0 100 200 300 400 500
20
40
60
80
100
120
140
160
180
200
220
240
280
260
00
50
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
0 20 40 60 80 100 120 140
0
0
100 200 300 400 500
4 8 12 16 20 24 3228
0 4 8 12 16 20 24 3228
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
ETA
Q/H
NPSH
31
50Hz
Dimensions and weightsType HP 50-110.2
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 50-110.2/1 1,1 80 405 637 405 637 232 160 170 129 23,5 35,5HP 50-110.2/2 2,2 90 415 682 415 682 267 180 170 138 25,5 41,5HP 50-110.2/3 4 112 473 779 473 779 306 196 170 145 27 49,8HP 50-110.2/4 5,5 132 708 1036 708 1036 328 225 300 161 49 83HP 50-110.2/5 5,5 132 756 1084 756 1084 328 225 300 161 50,5 84,5HP 50-110.2/6 7,5 132 804 1154 804 1154 350 225 300 161 52 88HP 50-110.2/7 7,5 132 852 1202 852 1202 350 225 300 161 53 89HP 50-110.2/8 11 160 920 1345 920 1345 425 248 350 198 57,5 115,5HP 50-110.2/9 11 160 968 1393 968 1393 425 248 350 198 59 117HP 50-110.2/10 11 160 1016 1441 1016 1441 425 248 350 198 60,5 118,5HP 50-110.2/11 15 160 1064 1540 - - 476 248 350 198 61,5 125,5HP 50-110.2/12 15 160 1112 1588 - - 476 248 350 198 63 127HP 50-110.2/13 15 160 1160 1636 - - 476 248 350 198 64,5 128,5HP 50-110.2/14 15 160 1208 1684 - - 476 248 350 198 66 130HP 50-110.2/15 18,5 160 1256 1798 - - 542 317 350 235 67,5 156,4HP 50-110.2/16 18,5 160 1304 1846 - - 542 317 350 235 68,5 157,4HP 50-110.2/17 18,5 160 1352 1894 - - 542 317 350 235 70 158,9
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional accesso-ries, including bolts and joints).Available from 1 to 10 stages
200
9026
,5
N° 2
x Ø
13
100L3
+ L
2L3
DN 50
DN 50
N°4 x Ø 13 130185
215
250
30026,5
90
L1L2
L1 +
L2
Ø 127
Ø 165
19N
° 4 x
Ø
Ø D1
M
D2
Round flange
Round flanges on body type PN25: the pump is supplied without counterflanges (Op-tional accessories, including bolts and joints).
32
Performance curveType HP 65-135.1
Speed 2900 rpm
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
MEI ≥ 0,70
m340
1100
1050
1000
950
900
850
800
750
700
650
550
450
350
250
150
50
0
600
500
400
300
200
100
320
300
280
260
240
220
200
180
160
140
120
100
80
60
40
20
00 5 10 15 20 25 30 35 40 45 50
m
U.S.gpm
l /min
m³/h
l /min
m³/h
30
50
70
m³/h
%
0 5 10 15 20 25 30 35 40 45 50
0 5 10 15 20 25 30 35 40 45 50
2200 20 40 60 80 100 120 140 160 180 200
76543210
0 100 200 300 400 500 600 700 800
0
8121620
4
ft
ft
1
2
2/22/1
3
3/23/1
4
4/24/1
5
5/25/1
6
6/26/1
7
7/27/1
8
8/28/1
9
9/29/1
1010/110/2
1111/111/2
1212/112/2
1313/113/2
ETA
Q/H
NPSH
33
50Hz
Dimensions and weightsType HP 65-135.1
Round flange
The pump is supplied without counterflanges (Optional acces-sories, including bolts and joints).
Type Motor Dimensions [mm] Weight [kg]kW Size L1 L1+L2 L2 D1 D2 M Pump Unit
HP 65-135.1/1 2,2 90 445 712 267 180 170 138 53 69HP 65-135.1/2/2 4 112 537 843 306 196 170 145 57 80HP 65-135.1/2/1 4 112 724 1030 306 196 170 145 74,5 97,5HP 65-135.1/2 5,5 132 724 1052 328 225 300 161 74,5 108,5HP 65-135.1/3/2 5,5 132 806 1134 328 225 300 161 78,5 112,5HP 65-135.1/3/1 7,5 132 806 1156 350 225 300 161 78,5 114,5HP 65-135.1/3 7,5 132 806 1156 350 225 300 161 78,5 114,5HP 65-135.1/4/2 7,5 132 888 1238 350 225 300 161 85,5 121,5HP 65-135.1/4/1 11 160 908 1333 425 248 350 198 85,5 143,5HP 65-135.1/4 11 160 908 1333 425 248 350 198 85,5 143,5HP 65-135.1/5/2 11 160 990 1415 425 248 350 198 89,5 147,5HP 65-135.1/5/1 11 160 990 1415 425 248 350 198 89,5 147,5HP 65-135.1/5 15 160 990 1466 476 248 350 198 89,5 153,5HP 65-135.1/6/2 15 160 1072 1548 476 248 350 198 93,5 157,5HP 65-135.1/6/1 15 160 1072 1548 476 248 350 198 93,5 157,5HP 65-135.1/6 15 160 1072 1548 476 248 350 198 93,5 157,5HP 65-135.1/7/2 15 160 1154 1630 476 248 350 198 97,5 161,5HP 65-135.1/7/1 15 160 1154 1630 476 248 350 198 97,5 161,5HP 65-135.1/7 18,5 160 1154 1696 542 317 350 238 97,5 186,5HP 65-135.1/8/2 18,5 160 1236 1778 542 317 350 238 101,5 190,5HP 65-135.1/8/1 18,5 160 1236 1778 542 317 350 238 101,5 190,5HP 65-135.1/8 18,5 160 1236 1778 542 317 350 238 101,5 190,5HP 65-135.1/9/2 22 180 1318 1860 542 360 350 238 105,5 214HP 65-135.1/9/1 22 180 1318 1860 542 360 350 238 105,5 214HP 65-135.1/9 22 180 1318 1860 542 360 350 238 105,5 214HP 65-135.1/10/2 22 180 1400 1942 542 360 350 238 112,5 221HP 65-135.1/10/1 22 180 1400 1942 542 360 350 238 112,5 221HP 65-135.1/10 30 200 1405 2063 658 399 400 297 112,5 340,5HP 65-135.1/11/2 30 200 1487 2145 658 399 400 297 116,5 344,5HP 65-135.1/11/1 30 200 1487 2145 658 399 400 297 116,5 344,5HP 65-135.1/11 30 200 1487 2145 658 399 400 297 116,5 344,5HP 65-135.1/12/2 30 200 1569 2227 658 399 400 297 120,5 348,5HP 65-135.1/12/1 30 200 1569 2227 658 399 400 297 120,5 348,5HP 65-135.1/12 30 200 1569 2227 658 399 400 297 120,5 348,5HP 65-135.1/13/2 30 200 1651 2309 658 399 400 297 124,5 352,5HP 65-135.1/13/1 30 200 1651 2309 658 399 400 297 124,5 352,5HP 65-135.1/13 30 200 1651 2309 658 399 400 297 124,5 352,5
3010
5L1
L1 +
L2
L2
320
170
220
Ø 15
N°4 ×
PN25-40PN16PN16-25-40
240
290
DN
65
Ø14
5
Ø18
5
D2
Ø19
M
D1
45° 22,5°
No 8xNo 4x
34
Performance curveType HP 80-135.1
Speed 2900 rpm
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
MEI ≥ 0,70
320
300
280
260
240
220
200
180
160
140
120
100
80
60
40
20
0
0
20 30 40 50 60 70
20 30 40 50 60 70
20 30 40 50 60 70
100 200 300 400 500 600 700 800 900 1000 1100 1200 1300
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300
0
U.S.gpm
l /min
m³/h
m
%
m³/h
m³/h
l /min
3401100
1050
1000
950
900
850
800
750
700
650
550
450
350
250
150
50
0
600
500
400
300
200
100
m
1010 80
0 1010 80
0 1010 80
0 40 80 120 160 200 240 280 320
2030405060708090
36322824201612840 0
2468
1012
ft
ft
11/1
2
2/2
3
3/2
4
4/2
5
5/2
6
6/2
7
7/2
8
8/2
9
9/2
10
10/2
11
11/2
12
12/2
13/2
ETA
Q/H
NPSH
35
50Hz
Dimensions and weightsType HP 80-135.1
Type Motor Dimensions [mm] Weight [kg]kW Size L1 L1+L2 L2 D1 D2 M Pump Unit
HP 80-135.1/1/1 3 100 490 757 267 180 170 138 59 78HP 80-135.1/1 4 112 490 796 306 196 170 145 59 82HP 80-135.1/2/2 5,5 132 759 1087 328 225 300 161 80,5 114,5HP 80-135.1/2 7,5 132 759 1109 350 225 300 161 80,5 116,5HP 80-135.1/3/2 11 160 861 1286 425 248 350 198 87,5 145,5HP 80-135.1/3 11 160 861 1286 425 248 350 198 87,5 145,5HP 80-135.1/4/2 15 160 943 1419 476 248 350 198 91,5 155,5HP 80-135.1/4 15 160 943 1419 476 248 350 198 91,5 155,5HP 80-135.1/5/2 18,5 160 1025 1567 542 317 350 238 95,5 184,5HP 80-135.1/5 18,5 160 1025 1567 542 317 350 238 95,5 184,5HP 80-135.1/6/2 22 180 1107 1649 542 317 350 238 99 208HP 80-135.1/6 22 180 1107 1649 542 317 350 238 99 208HP 80-135.1/7/2 30 200 1194 1852 658 399 400 297 106 334HP 80-135.1/7 30 200 1194 1852 658 399 400 297 106 334HP 80-135.1/8/2 30 200 1276 1934 658 399 400 297 110 338HP 80-135.1/8 30 200 1276 1934 658 399 400 297 110 338HP 80-135.1/9/2 37 200 1358 2016 658 399 400 297 114 356HP 80-135.1/9 37 200 1358 2016 658 399 400 297 114 356HP 80-135.1/10/2 37 200 1440 2098 658 399 400 297 118 360HP 80-135.1/10 37 200 1440 2098 658 399 400 297 118 360HP 80-135.1/11/2 45 225 1522 2221 699 465 450 333 125 433HP 80-135.1/11 45 225 1522 2221 699 465 450 333 125 433HP 80-135.1/12/2 45 225 1604 2303 699 465 450 333 129 437HP 80-135.1/12 45 225 1604 2303 699 465 450 333 129 437HP 80-135.1/13/2 45 225 1686 2385 699 465 450 333 133 441
36545
140
L1
L1 +
L2
L2 190
240
Ø 15
N°4 ×
265
316
PN16/25/40 Ø 16
0 Ø
200
Ø 19
N°8
×
D2
M
D1
DN
80
Round flange
The pump is supplied without counterflanges (Optional acces-sories, including bolts and joints).
36
Performance curveType HP 100-145.1
Speed 2900 rpm
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
MEI ≥ 0,70
U.S.gpm
l /min
m³/h
m³/h
m³/h
l /min
mfeet
feet m
%ETA
Q/H
NPSH
1
1/1
2
2/1
2/2
3
3/1
3/2
4
4/1
4/2
5
5/1
5/2
6
6/1
6/2
7
7/1
7/2
8
8/1
8/2
37
50Hz
Dimensions and weightsType HP 100-145.1
Type Motor Dimensions [mm] Weight [kg]kW Size L1 L1+L2 L2 D1 D2 M Pump Unit
HP 100-145.1/1/1 4 112 550,1 856,1 306 196 170 145 61 83,8HP 100-145.1/1 5,5 132 737,1 1065,1 328 225 300 161 81 115HP 100-145.1/2/2 7,5 132 829,2 1179,2 350 225 300 161 85,5 121,5HP 100-145.1/2/1 11 160 849,2 1274,2 425 248 350 198 88,5 146,5HP 100-145.1/2 11 160 849,2 1274,2 425 248 350 198 88,5 146,5HP 100-145.1/3/2 15 160 941,3 1417,3 476 248 350 198 93 157HP 100-145.1/3/1 15 160 941,3 1417,3 476 248 350 198 93 157HP 100-145.1/3 18,5 160 941,3 1483,3 542 317 350 235 93 181,9HP 100-145.1/4/2 18,5 160 1033,4 1575,4 542 317 350 235 97,5 186,4HP 100-145.1/4/1 22 180 1033,4 1575,4 542 317 350 238 98 206,7HP 100-145.1/4 22 180 1033,4 1575,4 542 317 350 238 98 206,7HP 100-145.1/5/2 30 200 1130,5 1788,5 658 399 400 300 105,5 333,5HP 100-145.1/5/1 30 200 1130,5 1788,5 658 399 400 300 105,5 333,5HP 100-145.1/5 30 200 1130,5 1788,5 658 399 400 300 105,5 333,5HP 100-145.1/6/2 30 200 1222,6 1880,6 658 399 400 300 110 338HP 100-145.1/6/1 37 200 1222,6 1880,6 658 399 400 300 110 352HP 100-145.1/6 37 200 1222,6 1880,6 658 399 400 300 110 352HP 100-145.1/7/2 37 200 1314,7 1972,7 658 399 400 300 114,5 356,5HP 100-145.1/7/1 37 200 1314,7 1972,7 658 399 400 300 114,5 356,5HP 100-145.1/7 45 225 1314,7 2013,7 699 465 450 335 117,5 425,5HP 100-145.1/8/2 45 225 1406,8 2105,8 699 465 450 335 122 430HP 100-145.1/8/1 45 225 1406,8 2105,8 699 465 450 335 122 430HP 100-145.1/8 45 225 1406,8 2105,8 699 465 450 335 122 430
��
4514
0
L1
L1 +
L2
L2
365
Ø19
N°8
×
PN16 PN25
Ø18
0
DN
100
DN
100
Ø23
0
D2
M
D1
Ø19
0
Ø25
5
Ø23
N°8
×
190
240
265
316
Ø 15
N°4 ×
*
* Available from 1/1 to 6/2
Round flange
The pump is supplied without counterflanges (Optional accessories, including bolts and joints).
38
Performance curveType HP 100-145.2
Speed 2900 rpm
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
MEI ≥ 0,70
m³/h
%
feet m
U.S.gpm
l /min
m³/h
mfeet
m³/h
l /min
1
1/1
2
2/2
3
3/2
4
4/2
5
5/2
6
6/2
ETA
Q/H
NPSH
39
50Hz
Dimensions and weightsType HP 100-145.2
Type Motor Dimensions [mm] Weight [kg]kW Size L1 L1+L2 L2 D1 D2 M Pump Unit
HP 100-145.2/1/1 5,5 132 737,1 1065,1 328 225 300 161 82,5 116,5HP 100-145.2/1 7,5 132 737,1 1087,1 350 225 300 161 82,5 118,5HP 100-145.2/2/2 11 160 849,2 1274,2 425 248 350 198 89 147HP 100-145.2/2 15 160 849,2 1325,2 476 248 350 198 89 153HP 100-145.2/3/2 18,5 160 941,3 1483,3 542 317 350 235 93 181,9HP 100-145.2/3 22 180 941,3 1483,3 542 317 350 238 93 201,7HP 100-145.2/4/2 30 200 1038,4 1696,4 658 399 400 300 100 328HP 100-145.2/4 30 200 1038,4 1696,4 658 399 400 300 100 328HP 100-145.2/5/2 37 200 1130,5 1788,5 658 399 400 300 104 346HP 100-145.2/5 37 200 1130,5 1788,5 658 399 400 300 104 346HP 100-145.2/6/2 45 225 1222,6 1921,6 699 465 450 335 110,5 418,5HP 100-145.2/6 45 225 1222,6 1921,6 699 465 450 335 110,5 418,5
���
4514
0
L1
L1 +
L2
L2
380
Ø19
N°8
×
PN16 PN25
Ø18
0
DN
100
DN
100
Ø23
0
D2
M
D1
Ø19
0
Ø25
5
Ø23
N°8
×
199
260
280
341
Ø 15
N°4 ×
*
* Available from 1/1 to 5
Round flange
The pump is supplied without counter-flanges (Optional ac-cessories, including bolts and joints).
40
Performance curveType HP 25-80.1
Speed 3500 rpm
0 10 20 30 40 50 60
0
0
40
80
120
160
200
240
280
0
10
20
30
40
50
60
70
80
90
100
110
320
360
10 20 30 40 50 60
0.00
0102030405060
1234567
6
02
10
14
18
22
0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6
0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6
0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6
0 2 4 6 8 10 12 14 16
10
9
8
7
6
5
4
3
2
ft m
ft m
%
m3/h
m3/h
l/min
m3/h
l/min
U.S. gpm
Q/H
ETA
NPSH
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
41
60Hz
Dimensions and weightsType HP 25-80.1
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 25-80.1/2 0,37 71 312,5 527,5 287,5 502,5 215 142 170 112 15 20,8HP 25-80.1/3 0,37 71 335 550 310 525 215 142 170 112 15 20,8HP 25-80.1/4 0,37 71 357,5 572,5 332,5 547,5 215 142 170 112 15,5 21,3HP 25-80.1/5 0,55 71 380 595 355 570 215 142 170 112 16 22,2HP 25-80.1/6 0,55 71 402,5 617,5 377,5 592,5 215 142 170 112 16,5 22,7HP 25-80.1/7 0,75 80 425 657 400 632 232 160 170 129 17 26,5HP 25-80.1/8 0,75 80 447,5 679,5 422,5 654,5 232 160 170 129 17,5 27HP 25-80.1/9 1,1 80 470 702 445 677 232 160 170 129 18 29,1HP 25-80.1/10 1,1 80 492,5 724,5 467,5 699,5 232 160 170 129 18,5 29,6
D2
25
75
L1L2
L1+L
2
M
D1
180
210
100
150
N°4xØ13
250
25
50
L3
L3+L
2
160
Ø115
Ø85
N°4x
Ø14
Rp 1DN 25
75
N°2 Screw/NutM10
Rp 1¼DN 32
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional ac-cessories, including bolts and joints).
Round flange
Round flanges on body type PN25: the pump is supplied without coun-terflanges (Optional accessories, including bolts and joints).
Available from 2 to 15 stages
42
Performance curveType HP 25-80.1
Speed 3500 rpm
0 10 20 30 40 50 60
0
100
200
250
150
300
350
400
450
500
550
600
650
700
750
800
20
40
60
80
100
120
140
160
200
180
220
240
260
280
850
900
10 20 30 40 50 60
0.00
0102030405060
1234567
0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6
0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6
0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6
0 2 4 6 8 10 12 14 16
6
02
10
14
18
22
25
22
15
17
19
1413
12
11
ft m
ft m
%
m3/h
m3/h
l/min
m3/h
l/min
U.S. gpm
Q/H
ETA
NPSH
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
43
60Hz
Dimensions and weightsType HP 25-80.1
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 25-80.1/11 1,1 80 515 747 490 722 232 160 170 129 19 30,1HP 25-80.1/12 1,1 80 537,5 769,5 512,5 744,5 232 160 170 129 19,5 30,6HP 25-80.1/13 1,5 90 570 837 545 812 267 180 170 138 20,5 34,5HP 25-80.1/14 1,5 90 592,5 859,5 567,5 834,5 267 180 170 138 21 35HP 25-80.1/15 1,5 90 615 882 590 857 267 180 170 138 21,5 35,5HP 25-80.1/17 2,2 90 660 927 - - 267 180 170 138 22 38HP 25-80.1/19 2,2 90 705 972 - - 267 180 170 138 23 39HP 25-80.1/22 2,2 90 772,5 1039,5 - - 267 180 170 138 24,5 40,5HP 25-80.1/25 3 100 850 1156 - - 306 196 170 145 26,5 49,3
D2
25
75
L1L2
L1+L
2
M
D1
180
210
100
150
N°4xØ13
250
25
50
L3
L3+L
2
160
Ø115
Ø85
N°4x
Ø14
Rp 1DN 25
75
N°2 Screw/NutM10
Rp 1¼DN 32
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional ac-cessories, including bolts and joints).
Round flange
Round flanges on body type PN25: the pump is supplied without coun-terflanges (Optional accessories, including bolts and joints).
Available from 2 to 15 stages
44
Performance curveType HP 25-80.2
Speed 3500 rpm
0
010203040506070
123456
46
02
81012141618
0 4 8 1612 2420
0 10 20 30 40 50 60 70 80 90 100
0 10 20 30 40 50 60 70 80 90 100
0.0 0.8 1.6 2.4 3.2 5.64.84.0
0.0 0.8 1.6 2.4 3.2 5.64.84.0
0.0 0.8 1.6 2.4 3.2 5.64.84.00
80
120
40
160
200
240
320
360
280
400
440
0
20
40
60
80
100
120
140
2
3
4
5
6
7
8
9
10
11
12
ft m
ft m
%
m3/h
m3/h
l/min
m3/h
l/min
U.S. gpm
Q/H
ETA
NPSH
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
45
60Hz
Dimensions and weightsType HP 25-80.2
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 25-80.2/2 0,37 71 312,5 528,5 287,5 503,5 216 142 170 112 15 20,8HP 25-80.2/3 0,55 71 335 551 310 526 216 142 170 112 15 21,2HP 25-80.2/4 0,55 71 357,5 573,5 332,5 548,5 216 142 170 112 15,5 21,7HP 25-80.2/5 0,75 80 380 612 355 587 232 160 170 129 16 25,5HP 25-80.2/6 1,1 80 402,5 634,5 377,5 609,5 232 160 170 129 16,5 27,6HP 25-80.2/7 1,1 80 425 657 400 632 232 160 170 129 17 28,1HP 25-80.2/8 1,5 90 457,5 724,5 432,5 699,5 267 180 170 138 18 32HP 25-80.2/9 1,5 90 480 747 455 722 267 180 170 138 18,5 32,5HP 25-80.2/10 1,5 90 502,5 769,5 477,5 744,5 267 180 170 138 19 33HP 25-80.2/11 2,2 90 525 792 500 767 267 180 170 138 19,5 35,5HP 25-80.2/12 2,2 90 547,5 814,5 522,5 789,5 267 180 170 138 20 36
D2
25
75
L1L2
L1+L
2
M
D1
180
210
100
150
N°4xØ13
250
25
50
L3
L3+L
2
160
Ø115
Ø85
N°4x
Ø14
Rp 1DN 25
75
N°2 Screw/NutM10
Rp 1¼DN 32
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional ac-cessories, including bolts and joints).
Round flange
Round flanges on body type PN25: the pump is supplied without coun-terflanges (Optional accessories, including bolts and joints).
Available from 2 to 14 stages
46
Performance curveType HP 25-80.2
Speed 3500 rpm
0
010203040506070
123456
46
02
81012141618
0 4 8 1612 2420
0 10 20 30 40 50 60 70 80 90 100
0 10 20 30 40 50 60 70 80 90 100
0.0 0.8 1.6 2.4 3.2 5.64.84.0
0.0 0.8 1.6 2.4 3.2 5.64.84.0
0.0 0.8 1.6 2.4 3.2 5.64.84.0
150
250
300
200
350
400
450
500
650
700
550
600
750
800
850
40
60
80
100
120
140
160
180
200
220
240
260
15
14
13
16
17
18
19
21
23
ft m
ft m
%
m3/h
m3/h
l/min
m3/h
l/min
U.S. gpm
Q/H
ETA
NPSH
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
47
60Hz
Dimensions and weightsType HP 25-80.2
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 25-80.2/13 2,2 90 570 837 545 812 267 180 170 138 20,5 36,5HP 25-80.2/14 2,2 90 592,5 859,5 567,5 834,5 267 180 170 138 21 37HP 25-80.2/15 2,2 90 615 882 - - 267 180 170 138 21,5 37,5HP 25-80.2/16 3 100 647,5 953,5 - - 306 196 170 145 22,5 45,3HP 25-80.2/17 3 100 670 976 - - 306 196 170 145 23 45,8HP 25-80.2/18 3 100 692,5 998,5 - - 306 196 170 145 23,5 46,3HP 25-80.2/19 3 100 715 1021 - - 306 196 170 145 24 46,8HP 25-80.2/21 4 112 760 1066 - - 306 196 170 145 25 51,5HP 25-80.2/23 4 112 805 1111 - - 306 196 170 145 25,5 52
D2
25
75
L1L2
L1+L
2
M
D1
180
210
100
150
N°4xØ13
250
25
50
L3
L3+L
2
160
Ø115
Ø85
N°4x
Ø14
Rp 1DN 25
75
N°2 Screw/NutM10
Rp 1¼DN 32
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional ac-cessories, including bolts and joints).
Round flange
Round flanges on body type PN25: the pump is supplied without coun-terflanges (Optional accessories, including bolts and joints).
Available from 2 to 14 stages
48
Performance curveType HP 32-80.1
Speed 3500 rpm
0 4 8 1612 2420 28 3632
0 20 40 8060 120100 140 160 180
0 20 40 8060 120100 140 160 180
0 1 2 43 65 7 8 11109
0 1 2 43 65 7 8 11109
0 1 2 43 65 7 8 11109
44 4840
46
02
81012141618
0123456
01020304050607080
0
100
50
150
200
250
400
300
350
450
500
0
20
40
60
80
100
120
140
160
2
3
4
5
6
7
8
9
10
11
12
13
ft m
ft m
%
m3/h
m3/h
l/min
m3/h
l/min
U.S. gpm
Q/H
ETA
NPSH
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
49
60Hz
Dimensions and weightsType HP 32-80.1
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 32-80.1/2 0,55 71 319,5 535,5 294,5 510,5 216 142 170 112 15 21,2HP 32-80.1/3 0,75 80 345,5 577,5 320,5 552,5 232 160 170 129 15,5 25HP 32-80.1/4 1,1 80 371,5 603,5 346,5 578,5 232 160 170 129 16 27,1HP 32-80.1/5 1,1 80 397,5 629,5 372,5 604,5 232 160 170 129 16,5 27,6HP 32-80.1/6 1,5 90 433,5 700,5 408,5 675,5 267 180 170 138 17,5 31,5HP 32-80.1/7 1,5 90 459,5 726,5 434,5 701,5 267 180 170 138 18,5 32,5HP 32-80.1/8 2,2 90 485,5 752,5 460,5 727,5 267 180 170 138 19 35HP 32-80.1/9 2,2 90 511,5 778,5 486,5 753,5 267 180 170 138 19,5 35,5HP 32-80.1/10 2,2 90 537,5 804,5 512,5 779,5 267 180 170 138 20 36HP 32-80.1/11 3 100 573,5 879,5 548,5 854,5 306 196 170 145 21 43,8HP 32-80.1/12 3 100 599,5 905,5 574,5 880,5 306 196 170 145 21,5 44,3HP 32-80.1/13 3 100 625,5 931,5 600,5 906,5 306 196 170 145 22 44,8
D2
25
75
L1L2
L1+L
2
M
D1
180
210
100
150
N°4xØ13
250
25
50
L3
L3+L
2
160
Ø140
Ø100
N°4x
Ø18
Rp 1¼DN 32
75
N°2 Screw/NutM10
Rp 1¼DN 32
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional ac-cessories, including bolts and joints).
Round flange
Round flanges on body type PN25: the pump is supplied without coun-terflanges (Optional accessories, including bolts and joints).
Available from 2 to 14 stages
50
Performance curveType HP 32-80.1
Speed 3500 rpm
0 4 8 1612 2420 28 3632
0 20 40 8060 120100 140 160 180
0 20 40 8060 120100 140 160 180
0 1 2 43 65 7 8 11109
0 1 2 43 65 7 8 11109
0 1 2 43 65 7 8 11109
44 4840
46
02
81012141618
0123456
01020304050607080
200
150
250
300
350
500
400
450
550
600
700
650
750
800
850
900
40
60
80
100
120
140
160
180
200
220
240
260
280
14
15
16
17
18
19
20
21
23
ft m
ft m
%
m3/h
m3/h
l/min
m3/h
l/min
U.S. gpm
Q/H
ETA
NPSH
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
51
60Hz
Dimensions and weightsType HP 32-80.1
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 32-80.1/14 3 100 651,5 957,5 626,5 932,5 306 196 170 145 22,5 45,3HP 32-80.1/15 4 112 677,5 983,5 - - 306 196 170 145 23 49,5HP 32-80.1/16 4 112 703,5 1009,5 - - 306 196 170 145 23,5 50HP 32-80.1/17 4 112 729,5 1035,5 - - 306 196 170 145 24 50,5HP 32-80.1/18 4 112 755,5 1061,5 - - 306 196 170 145 24,5 51HP 32-80.1/19 5,5 132 957 1285 - - 328 225 300 160 44,5 78,1HP 32-80.1/20 5,5 132 983 1311 - - 328 225 300 160 45 78,6HP 32-80.1/21 5,5 132 1009 1337 - - 328 225 300 160 45,5 79,1HP 32-80.1/23 5,5 132 1061 1389 - - 328 225 300 160 46,5 80,1
D2
25
75
L1L2
L1+L
2
M
D1
180
210
100
150
N°4xØ13
250
25
50
L3
L3+L
2
160
Ø140
Ø100
N°4x
Ø18
Rp 1¼DN 32
75
N°2 Screw/NutM10
Rp 1¼DN 32
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional ac-cessories, including bolts and joints).
Round flange
Round flanges on body type PN25: the pump is supplied without coun-terflanges (Optional accessories, including bolts and joints).
Available from 2 to 14 stages
52
Performance curveType HP 40-95.1
Speed 3500 rpm
0 5 10 2015 3025 35 4540 55 85807570656050
0 30 60 12090 180150 210 240 330300270
0 30 60 12090 180150 210 240 330300270
0 2 4 86 1210 14 201816
0 2 4 86 1210 14 201816
0 2 4 86 1210 14 201816
012345678
4
0
8
12
16
20
24
01020304050607080
0
100
50
150
200
250
400
300
350
450
0
20
40
60
80
100
120
140
2
3
4
5
6
7
8
9
ft m
ft m
%
m3/h
m3/h
l/min
m3/h
l/min
U.S. gpm
Q/H
ETA
NPSH
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
53
60Hz
Dimensions and weightsType HP 40-95.1
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 40-95.1/2 1,1 80 347,5 579,5 347,5 579,5 232 160 170 129 17,5 28,6HP 40-95.1/3 2,2 90 387,5 654,5 387,5 654,5 267 180 170 138 18,5 34,5HP 40-95.1/4 2,2 90 417,5 684,5 417,5 684,5 267 180 170 138 19,5 35,5HP 40-95.1/5 3 100 457,5 763,5 457,5 763,5 306 196 170 145 20,5 43,3HP 40-95.1/6 4 112 487,5 793,5 487,5 793,5 306 196 170 145 21 47,5HP 40-95.1/7 4 112 517,5 823,5 517,5 823,5 306 196 170 145 22 48,5HP 40-95.1/8 5,5 132 723 1051 723 1051 328 225 300 160 42 75,6HP 40-95.1/9 5,5 132 753 1081 753 1081 328 225 300 160 42,5 76,1
27,5
80
L1L2
L1+L
2
M
D1
215
250
130
185
N°4xØ13
280
27,7
80
L3
L3+L
2
200
Ø150
Ø110
N°4x
Ø18
Rp 1½DN 40
100
N°2 Screw/NutM12
Rp 1½DN 40
D2
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional ac-cessories, including bolts and joints).
Round flange
Round flanges on body type PN25: the pump is supplied without coun-terflanges (Optional accessories, including bolts and joints).
Available from 2 to 10 stages
54
Performance curveType HP 40-95.1
Speed 3500 rpm
0 5 10 2015 3025 35 4540 55 85807570656050
0 30 60 12090 180150 210 240 330300270
0 30 60 12090 180150 210 240 330300270
0 2 4 86 1210 14 201816
0 2 4 86 1210 14 201816
0 2 4 86 1210 14 201816
012345678
4
0
8
12
16
20
24
01020304050607080
200
150
250
300
350
500
400
450
550
600
650
800
700
750
850
40
60
80
100
120
140
160
220
200
180
240
260
17
15
13
12
11
10
ft m
ft m
%
m3/h
m3/h
l/min
m3/h
l/min
U.S. gpm
Q/H
ETA
NPSH
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
55
60Hz
Dimensions and weightsType HP 40-95.1
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 40-95.1/10 7,5 132 783 1111 783 1111 328 225 300 160 43,5 77,1HP 40-95.1/11 7,5 132 813 1163 - - 350 225 300 160 44 80HP 40-95.1/12 7,5 132 843 1193 - - 350 225 300 160 44,5 80,5HP 40-95.1/13 7,5 132 873 1223 - - 350 225 300 160 45,5 81,5HP 40-95.1/15 11 160 953 1378 - - 425 248 350 194 49 111HP 40-95.1/17 11 160 1013 1438 - - 425 248 350 194 50,5 112,5
27,5
80
L1L2
L1+L
2
M
D1
215
250
130
185
N°4xØ13
280
27,7
80
L3
L3+L
2
200
Ø150
Ø110
N°4x
Ø18
Rp 1½DN 40
100
N°2 Screw/NutM12
Rp 1½DN 40
D2
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional ac-cessories, including bolts and joints).
Round flange
Round flanges on body type PN25: the pump is supplied without coun-terflanges (Optional accessories, including bolts and joints).
Available from 2 to 10 stages
56
Performance curveType HP 50-110.1
Speed 3500 rpm
0 100 200 300 400 500
0 100 200 300 400 500
0012345678
20304050607080
50
0
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
4 8 12 16 20 24 3228
0 4 8 12 16 20 24 3228
0 4 8 12 16 20 24 3228
0 20 40 60 80 100 120 140
0
20
40
60
80
100
120
140
160
180
200
220
240
260
280
02
6
10
14
18
22
26
ft m
ft m
%
m3/h
m3/h
l/min
m3/h
l/min
U.S. gpm
12
11
10
9
8
7
6
5
4
3
2
1
Q/H
ETA
NPSH
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
57
60Hz
Dimensions and weightsType HP 50-110.1
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 50-110.1/1 1,5 90 415 682 415 682 267 180 170 138 24 38,0HP 50-110.1/2 3 100 425 715 425 715 290 180 170 138 26 44HP 50-110.1/3 4 112 473 779 473 779 306 196 170 145 27 49,8HP 50-110.1/4 5,5 132 707,9 1035,9 707,9 1035,9 328 225 300 161 49 83HP 50-110.1/5 7,5 132 755,9 1105,9 755,9 1105,9 350 225 300 161 50,5 86,5HP 50-110.1/6 11 160 823,9 1248,9 823,9 1248,9 425 248 350 198 54,5 112,5HP 50-110.1/7 11 160 871,9 1296,9 871,9 1296,9 425 248 350 198 56 114HP 50-110.1/8 11 160 919,9 1344,9 - - 425 248 350 198 57,5 115,5HP 50-110.1/9 15 160 967,9 1443,9 - - 476 248 350 198 59 123HP 50-110.1/10 15 160 1015,9 1491,9 - - 476 248 350 198 60,5 124,5HP 50-110.1/11 15 160 1063,9 1539,9 - - 476 248 350 198 61,5 125,5HP 50-110.1/12 18,5 160 1111,9 1653,9 - - 542 317 350 238 63 161
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional accesso-ries, including bolts and joints).Available from 1 to 7 stages
200
9026
,5
N° 2
x Ø
13
100L3
+ L
2L3
DN 50
DN 50
N°4 x Ø 13 130185
215
250
30026,5
90
L1L2
L1 +
L2
Ø 127
Ø 165
19N
° 4 x
Ø
Ø D1
M
D2
Round flange
Round flanges on body type PN25: the pump is supplied without counterflanges (Op-tional accessories, including bolts and joints).
58
Performance curveType HP 50-110.2
Speed 3500 rpm
0 20 40 60 80 100 120
0
0 4 8 12 16 20 24 28 32 36 40
0 4 8 12 16 20 24 28 32 36 40
0012345678
20
0
20
40
60
80
100
120
140
160
180
200
220
240
260
0
50
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
304050607080
4 8 12 16 20 24 28 32 36 40
100 200 300 400 500 600
0 100 200 300 400 500 600
140 160
02
6
10
14
18
22
26
ft m
ft m
%
m3/h
m3/h
l/min
m3/h
l/min
U.S. gpm
10
9
8
7
6
5
4
3
2
1
Q/H
ETA
NPSH
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
59
60Hz
Dimensions and weightsType HP 50-110.2
Type Motor Dimensions [mm] Weight [kg]Round flange Oval flange
kW Size L1 L1+L2 L3 L3+L2 L2 D1 D2 M Pump UnitHP 50-110.2/1 2,2 90 415 682 415 682 267 180 170 138 24 40,0HP 50-110.2/2 4 112 425 731 425 731 306 196 170 145 26 48,8HP 50-110.2/3 5,5 132 659,9 987,9 659,9 987,9 328 225 300 161 47,5 81,5HP 50-110.2/4 7,5 132 707,9 1057,9 707,9 1057,9 350 225 300 161 49 85HP 50-110.2/5 11 160 775,9 1200,9 775,9 1200,9 425 248 350 198 53 111HP 50-110.2/6 11 160 823,9 1248,9 823,9 1248,9 425 248 350 198 54,5 112,5HP 50-110.2/7 15 160 871,9 1347,9 871,9 1347,9 476 248 350 198 56 120HP 50-110.2/8 15 160 919,9 1395,9 - - 476 248 350 198 57,5 121,5HP 50-110.2/9 18,5 160 967,9 1509,9 - - 542 317 350 238 59 157HP 50-110.2/10 18,5 160 1015,9 1557,9 - - 542 317 350 238 60,5 158,5
Oval flange
Oval flanges on body type PN16: the pump is supplied without threaded oval counter flanges (Optional accesso-ries, including bolts and joints).Available from 1 to 7 stages
200
9026
,5
N° 2
x Ø
13
100L3
+ L
2L3
DN 50
DN 50
N°4 x Ø 13 130185
215
250
30026,5
90
L1L2
L1 +
L2
Ø 127
Ø 165
19N
° 4 x
Ø
Ø D1
M
D2
Round flange
Round flanges on body type PN25: the pump is supplied without counterflanges (Op-tional accessories, including bolts and joints).
60
Performance curveType HP 65-135.1
Speed 3500 rpm
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
9
76
8
543210
2030405060708090
2824
1620
12
48
0550 5 10 15 20 25 30 35 40 45 50
550 5 10 15 20 25 30 35 40 45 50
550 5 10 15 20 25 30 35 40 45 50
220 2400 20 40 60 80 100 120 140 160 180 200
0 100 200 300 400 500 600 700 800 900
0
0 0
20
40
60
80
100
120
140
160
180
200
220
240
260
280
300
50
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
100 200 300 400 500 600 700 800 900
ft m
ft m
%
m3/h
m3/h
l/min
m3/h
l/min
U.S. gpm
8/18/2
8
7/17/2
7
6/16/2
6
5/15/2
5
4/14/2
4
3/13/2
3
2/12/2
2
1/11
Q/H
ETA
NPSH
61
60Hz
Dimensions and weightsType HP 65-135.1
Type Motor Dimensions [mm] Weight [kg]kW Size L1 L1+L2 L2 D1 D2 M Pump Unit
HP 65-135.1/1/1 3 100 455 745 290 180 170 138 53 71HP 65-135.1/1 4 112 455 761 306 196 170 145 53 75,8HP 65-135.1/2/2 5,5 132 724 1052 328 225 300 161 74,5 108,5HP 65-135.1/2/1 7,5 132 724 1074 350 225 300 161 74,5 110,5HP 65-135.1/2 11 160 744 1169 425 248 350 198 77,5 135,5HP 65-135.1/3/2 11 160 826 1251 425 248 350 198 81,5 139,5HP 65-135.1/3/1 11 160 826 1251 425 248 350 198 81,5 139,5HP 65-135.1/3 15 160 826 1302 476 248 350 198 81,5 145,5HP 65-135.1/4/2 15 160 908 1384 476 248 350 198 85,5 149,5HP 65-135.1/4/1 15 160 908 1384 476 248 350 198 85,5 149,5HP 65-135.1/4 18,5 160 908 1450 542 317 350 238 85,5 183,5HP 65-135.1/5/2 18,5 160 990 1532 542 317 350 238 89,5 187,5HP 65-135.1/5/1 18,5 160 990 1532 542 317 350 238 89,5 187,5HP 65-135.1/5 22 180 990 1532 542 317 350 238 89,5 198,5HP 65-135.1/6/2 22 180 1072 1614 542 317 350 238 93,5 202,5HP 65-135.1/6/1 22 180 1072 1614 542 317 350 238 93,5 202,5HP 65-135.1/6 30 200 1077 1735 658 399 400 300 96,5 324,5HP 65-135.1/7/2 30 200 1159 1817 658 399 400 300 100,5 328,5HP 65-135.1/7/1 30 200 1159 1817 658 399 400 300 100,5 328,5HP 65-135.1/7 30 200 1159 1817 658 399 400 300 100,5 328,5HP 65-135.1/8/2 30 200 1241 1899 658 399 400 300 104,5 332,5HP 65-135.1/8/1 37 200 1241 1899 658 399 400 300 104,5 346,5HP 65-135.1/8 37 200 1241 1899 658 399 400 300 104,5 346,5
Round flange
The pump is supplied without counterflanges (Optional accessories, including bolts and joints).
3010
5L1
L1 +
L2
L2
320
170
220
Ø 15
N°4 ×
PN25-40PN16PN16-25-40
240
290
DN
65
Ø14
5
Ø18
5
D2Ø
19
M
D1
45° 22,5°
No 8xNo 4x
62
Performance curveType HP 80-135.1
Speed 3500 rpm
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
0 10 20 30 40 50 60 70 80 90
0 10 20 30 40 50 60 70 80 90
0 10 20 30 40 50 60 70 80 90
0
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500
40 80 120 160 200 240 280 320 360
00
50
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
20
40
60
80
100
120
140
160
180
200
220
240
260
00
12
4
20
28
3612
2030405060708090
10
8
6
4
2
ft m
ft m
%
m3/h
m3/h
l/min
m3/h
l/min
U.S. gpm
7/27/17
6/26/16
5/25/15
4/24/14
3/23/13
2/22/12
1/11
Q/H
ETA
NPSH
63
60Hz
Dimensions and weightsType HP 80-135.1
Type Motor Dimensions [mm] Weight [kg]kW Size L1 L1+L2 L2 D1 D2 M Pump Unit
HP 80-135.1/1/1 5,5 132 677 1005 328 225 300 161 76,5 110,5HP 80-135.1/1 7,5 132 677 1027 350 225 300 161 76,5 112,5HP 80-135.1/2/2 11 160 779 1204 425 248 350 198 83,5 141,5HP 80-135.1/2/1 11 160 779 1204 425 248 350 198 83,5 141,5HP 80-135.1/2 15 160 779 1255 476 248 350 198 83,5 147,5HP 80-135.1/3/2 18,5 160 861 1403 542 317 350 238 87,5 185,5HP 80-135.1/3/1 18,5 160 861 1403 542 317 350 238 87,5 185,5HP 80-135.1/3 18,5 160 861 1403 542 317 350 238 87,5 185,5HP 80-135.1/4/2 22 180 943 1485 542 317 350 238 91 200HP 80-135.1/4/1 30 200 948 1606 658 399 400 300 94 322HP 80-135.1/4 30 200 948 1606 658 399 400 300 94 322HP 80-135.1/5/2 30 200 1030 1688 658 399 400 300 98 326HP 80-135.1/5/1 30 200 1030 1688 658 399 400 300 98 326HP 80-135.1/5 37 200 1030 1688 658 399 400 300 98 340HP 80-135.1/6/2 37 200 1112 1770 658 399 400 300 102 344HP 80-135.1/6/1 37 200 1112 1770 658 399 400 300 102 344HP 80-135.1/6 37 200 1112 1770 658 399 400 300 102 344HP 80-135.1/7/2 45 225 1194 1893 699 465 450 335 109 417HP 80-135.1/7/1 45 225 1194 1893 699 465 450 335 109 417HP 80-135.1/7 45 225 1194 1893 699 465 450 335 109 417
36545
140
L1
L1 +
L2
L2 190
240
Ø 15
N°4 ×
265
316
PN16/25/40 Ø 16
0 Ø
200
Ø 19
N°8
×
D2
M
D1
DN
80
Round flange
The pump is supplied without counterflanges (Optional accessories, including bolts and joints).
64
Performance curveType HP 100-145.1
Speed 3500 rpm
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
0 10 20 30 40 50 60 70 80 90 100 110 120
0
0
0 200 400 600 800 1000 1200 1400 1600 1800 2000
40 80 120 160 200 240 280 320 360 400 440 480 520
10 20 30 40 50 60 70 80 90 100 110 120
0 10 20 30 40 50 60 70 80 90 100 110 120
0
20
40
60
80
100
120
140
160
180
200
0
50
100
150
200
250
300
350
400
450
500
550
600
650
0 200 400 600 800 1000 1200 1400 1600 1800 2000
2030405060708090
02468
1012
1614
08
162432404852
ft m
ft m
%
m3/h
m3/h
l/min
m3/h
l/min
U.S. gpm
1/1
2/2
2/1
3/2
3/1
1
2
3
4/2
4/1
5/2
5/1
4
Q/H
ETA
NPSH
65
60Hz
Dimensions and weightsType HP 100-145.1
Type PN Motor Dimensions [mm] Weight [kg]kW Size L1 L1+L2 L2 D1 D2 M Pump Unit
HP 100-145.1/1/1 16 7,5 132 737,1 1087,1 350 225 300 161 81 117HP 100-145.1/1 16 11 160 757,1 1182,1 425 248 350 198 84 142HP 100-145.1/2/2 16 15 160 849,2 1325,2 476 248 350 198 88,5 152,5HP 100-145.1/2/1 16 18,5 160 849,2 1391,2 542 317 350 238 88,5 186,5HP 100-145.1/2 16 22 180 849,2 1391,2 542 317 350 238 89 198HP 100-145.1/3/2 16 22 180 941,3 1483,3 542 317 350 238 93,5 202,5HP 100-145.1/3/1 16 30 200 946,3 1604,3 658 399 400 300 96,5 324,5HP 100-145.1/3 16 30 200 946,3 1604,3 658 399 400 300 96,5 324,5HP 100-145.1/4/2 16 37 200 1038,4 1696,4 658 399 400 300 101 343HP 100-145.1/4/1 16 37 200 1038,4 1696,4 658 399 400 300 101 343HP 100-145.1/4 16 45 225 1038,4 1737,4 699 465 450 335 104 412HP 100-145.1/5/2 25 45 225 1130,5 1829,5 699 465 450 335 108,5 416,5HP 100-145.1/5/1 25 45 225 1130,5 1829,5 699 465 450 335 108,5 416,5
��
4514
0
L1
L1 +
L2
L2
365
Ø19
N°8
×
PN16 PN25
Ø18
0
DN
100
DN
100
Ø23
0
D2
M
D1
Ø19
0
Ø25
5
Ø23
N°8
×
190
240
265
316
Ø 15
N°4 ×
*
* Available from 1/1 to 4/1
Round flange
The pump is supplied without counterflanges (Optional accessories, including bolts and joints).
66
Performance curveType HP 100-145.2
Speed 3500 rpm
Notes to performance curves: Curves valid according to DIN EN ISO 9906/3B.
04
122028364452
0
42
86
1210
1614
0
20
40
60
80
100
120
140
160
0
50
100
150
200
250
300
350
400
450
500
550
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140
0 40 80 120 160 200 240 280 320 360 400 440 480 520 600 640560
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400
150
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
ft m
ft m
%
m3/h
m3/h
l/min
m3/h
l/min
U.S. gpm
4/2
3/1
3/2
2/1
2/2
1/1
3
2
1
Q/H
ETA
NPSH
67
60Hz
Dimensions and weightsType HP 100-145.2
Type PN Motor Dimensions [mm] Weight [kg]kW Size L1 L1+L2 L2 D1 D2 M Pump Unit
HP 100-145.2/1/1 16 11 132 737,1 1162,1 425 248 300 198 82,5 140,5HP 100-145.2/1 16 15 160 757,1 1233,1 476 248 350 198 85,5 149,5HP 100-145.2/2/2 16 18,5 160 849,2 1391,2 542 317 350 238 89 187HP 100-145.2/2/1 16 22 180 849,2 1391,2 542 317 350 238 89,5 198,5HP 100-145.2/2 16 30 200 854,2 1512,2 658 399 400 300 92,5 320,5HP 100-145.2/3/2 16 37 200 946,3 1604,3 658 399 400 300 96,5 338,5HP 100-145.2/3/1 16 37 200 946,3 1604,3 658 399 400 300 96,5 338,5HP 100-145.2/3 16 45 225 946,3 1645,3 699 465 450 335 99,5 407,5HP 100-145.2/4/2 16 45 225 1038,4 1737,4 699 465 450 335 103 411
���
4514
0
L1
L1 +
L2
L2
380
Ø19
N°8
×
PN16 PN25
Ø18
0
DN
100
DN
100
Ø23
0
D2
M
D1
Ø19
0
Ø25
5
Ø23
N°8
×
199
260
280
341
Ø 15
N°4 ×
*
* Available from 1/1 to 4/2
Round flange
The pump is supplied without counter-flanges (Optional ac-cessories, including bolts and joints).
68
Cross section
Cross section and part listHP 25-80, HP 32-80, HP 40-95
20.00
10.01
10.02
10.03
10.04
10.06
20.07
30.02
30.03
30.02
40.04
40.05
50.03
20.02
20.03
20.01
20.09
30.0020.04
20.05
20.06
20.08
30.01
30.03
10.00
40.00
40.01
40.02
40.03
40.06
50.00
50.01
50.02
20.07
20.09
20.04
20.05
20.06
20.08
30.01
30.03
20.07
20.09
10.06
20.07
20.02
20.03
20.01
20.09
30.00
30.02
Part list Description10.00 Pump casing
10.01 Pump fixing plate
10.02 Filling and draining plug
10.03 Tie bolt
10.04 Kit nuts and washers
10.06 Upper flange
20.00 Outer Case
20.01 Mechanical seal housing
20.02 Motor flange
20.03 Motor bracket
20.04 Coupling guard
20.05 Filling plugs
20.06 Circlips and bearings, and O-ring
20.07 Coupling fasteners
20.08 Coupling
20.09 Kit motor screws
Part list Description30.00 Pump shaft
30.01 Kit Mechanical seal
30.02 Mechanical seal fastening kit
30.03 Kit O-rings
40.00 Stage housing and diffuser
40.01 Stage Centering outlet
40.02 Floating neck ring
40.03 Initial stage housing
40.04 Last Stage with diffuser
40.05 Stage Centering inlet
40.06 Stage housing and diffuser with bearing
50.00 Impeller
50.01 Impeller spacer
50.02 Intermediary sleeve
50.03 Intermediary sleeve spacer
(Configuration from 5,5kW)(Configuration up to 4kW)
69
Cross section
Cross section and part listHP 50-110
20.05
20.09
20.04
20.07
20.06
20.02
20.09
20.08
20.0330.00
30.01
30.02
20.09
20.06
20.04
20.07
20.0820.09
20.0530.00
30.01
50.00
30.02
40.02
50.0210.00
40.00
40.06
40.0330.02
10.0210.01
30.03
50.03
10.03
50.01
40.01
20.01
20.03
20.10
20.02
10.06
10.04
40.04
20.00
30.03
Part list Description10.00 Pump casing
10.01 Pump fixing plate
10.02 Filling and draining plug
10.03 Tie bolt
10.04 Kit nuts and washers
10.06 Upper Flange
20.00 Outer Case
20.01 Mechanical seal housing
20.02 Motor flange
20.03 Motor bracket
20.04 Coupling guard
20.05 Filling plugs
20.06 Circlips and bearings, and O-ring
20.07 Coupling fasteners
20.08 Coupling
20.09 Kit motor screws
Part list Description20.10 Motor shaft adapter
30.00 Pump shaft
30.01 Kit Mechanical seal
30.02 Mechanical seal fastening kit
30.03 Kit O-rings
40.00 Stage housing and diffuser
40.01 Stage Centering outlet
40.02 Floating neck ring
40.03 Initial stage housing
40.04 Last Stage with diffuser
40.06 Stage housing and diffuser with bearing
50.00 Impeller
50.01 Impeller spacer
50.02 Intermediary sleeve
50.03 Intermediary sleeve spacer
(Configuration from 5,5kW)
(Configuration up to 4kW)
70
Cross section
Cross section and part listHP 65-135, HP 80-135, HP 100-145
Part list Description10.00 Pump casing10.01 Pump fixing plate10.02 Draining plug10.03 Tie bolt10.04 Kit nuts and washers10.05 Kit flanges ring10.06 Upper Flange20.00 Outer Case20.01 Mechanical seal housing20.02 Motor flange20.03 Motor bracket20.04 Coupling guard20.05 Filling plugs20.06 Circlips and bearings, and O-ring20.07 Coupling fasteners20.08 Coupling20.09 Kit motor screws20.10 Motor shaft adapter
Part list Description30.00 Pump shaft30.01 Kit Mechanical seal30.02 Mechanical seal fastening kit30.03 Kit O-rings40.00 Stage housing and diffuser40.01 Stage Centering outlet (only on HP 100-145)40.02 Floating neck ring40.05 Stage Centering inlet40.06 Stage housing and diffuser with bearing40.07 Flange clamping neck ring40.08 Spring ring50.00 Impeller51.01 Split cone51.02 Intermediary sleeve nut51.03 Journal sleeve51.04 Split cone nut51.05 Intermediate impeller with screw
�����
�����
20.09
20.06
20.0420.07
20.09
30.01
30.0350.0040.0040.0240.0751.05
51.0151.04
40.06
40.05
10.05
51.0330.02
10.01
10.02
30.03
10.00
10.03
20.00
20.01
20.03
20.10
40.0130.00
30.02
10.0610.04
51.02
20.0540.08
20.08
20.02
20.09
20.07
20.06
30.02
20.05
30.0130.00
20.03
20.0920.02
20.0820.04
(Configuration from 5,5kW)
(Configuration up to 4kW)
71
For your notes
ANDRITZ Ritz GmbHGüglingstraße 5073529 Schwäbisch Gmünd, GermanyPhone: +49 (0)7171 609 0Fax: +49 (0)7171 609 [email protected]
All data, information, statements, photographs and graphic illustrations made in this leaflet are without any obligation and raise no liabilities to or form part of any sales contracts of Andritz AG or any affiliates for equipment and/or systems referred to herein. © Andritz AG 2015. All rights reserved. No part of this copyrighted work may be reproduced, modified or distributed in any form or by any means, or stored in any database or retrieval system, without the prior written permission of Andritz AG or its affiliates. Any such unauthorized use for any purpose is a violation of the relevant copyright laws. Andritz AG, Stattegger Strasse 18, 8045 Graz, Austria.
Close to our customers
www.andritz.com/pumps
4048448/06.16