hi-lume a-series driver overview forward phase control · pdf filehi-lume ® a-series...

Hi-lumeTM A-Series LTE – Japan

® SPECIF ICAT ION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

LED Dimming Driver Architectural Dimming

369677e 1 08.07.2015

Hi-lume® A-Series Driver Overview Forward Phase Control

The Hi-lume® A-Series Driver is a high-performance LED driver that provides smooth, continuous 1% dimming for constant current LED modules.

Features• Continuous, flicker-free dimming from 100% to 1%.• Guaranteed compatibility with selected HomeWorks®,

GRAFIK Eye® QS, and GRAFIK SystemsTM dimmers. Please see the chart “Compatible Controls” at the end of this document or contact Lutron Asuka for details regarding compatible controls.

• 100% performance-tested at factory.• A rated lifetime of 50 000 hours @ tc = 65 °C.• PSE Certified.• RoHS Compliant.• Pulse width modulation (PWM) or constant current

reduction (CCR) dimming methods available. See Application Note #360 for details.

• For more information please go to: www.lutron.com/HilumeLED

Hi-lume® A-Series, case type K76 mm W × 25 mm H × 124 mm L



Job Name:

Job Number:

Model Numbers:


369677e 2 08.07.2015

Specifications

Performance• Dimming Range: 100% to 1%• Operating Voltage: 100 V~ at 50/60 Hz (Forward

Phase Control)• A rated lifetime of 50,000 hours @ tc = 149 °F (65 °C).

– For rated warranty, tc not to exceed the maximum rated temperatures. 1

• Patented thermal foldback protection.• LEDs turn on to any dimmed level without going to full

brightness.• Nonvolatile memory restores all driver settings after

power failure.• Power Factor: > 0.90 at 40 W• Total Harmonic Distortion (THD): < 20% at 40 W• Inrush Current: < 2 A• Inrush Current Limiting Circuitry: eliminates circuit

breaker tripping, switch arcing and relay failure.• Open circuit protected• Short circuit protected• Turn-on time: ≤ 1.5 seconds 2

• PWM Dimming Frequency: 550 Hz

Environmental• Sound Rating: Class A.• Relative Humidity: Maximum 90% non-condensing.• Minimum operating ambient temperature (ta) = 0 °C.

Standards• Meets IEEE C62.41 category A surge protection

standards up to and including 4 kV.• Manufacturing facilities employ ESD reduction

practices that comply with the requirements of ANSI/ESD S20.20.

• Lutron® Quality Systems registered to ISO 9001.2008.• H PSE certified.

Driver Wiring and Mounting• Driver is grounded by a mounting screw to the

grounded fixture or by terminal connection.• Terminal blocks on the driver accept one solid wire

per terminal from Ø 1.024 mm (18 AWG) to Ø 1.29 mm (16 AWG).

• Fixture must be grounded in accordance with local and national electrical codes.

• Do not use more than 1 wire per connector terminal. Connector terminals are not rated for daisy-chain wiring.

• Maximum driver-to-LED light engine wire length for Constant Current Drivers:

Wire Gauge ØMaximum Lead Length

200 mA to 700 mA 710 mA to 1.50 A1.024 mm (18 AWG) 9 m 4.5 m1.29 mm (16 AWG) 10.5 m 7.5 m1.63 mm (14 AWG) 15 m 12 m2.05 mm (12 AWG) 30 m 18 m

Note: For wire gauges larger than Ø 1.29 mm (16 AWG), use external connector for connection with driver

1 Installer is responsible for ensuring that the driver case temperature does not exceed the maximum rated temperature.2 Models available with turn-on time ≤ 1 second.



Job Name:

Job Number:

Model Numbers:


369677e 3 08.07.2015

How to Build a Model Number: Hi-lume® A-Series

Case Style:S = Studded N = Non-Studded

Driver Output:C = Constant current driver with pulse width modulation (PWM) dimmingA = Constant current driver with constant current reduction (CCR) dimming

Current Level (for Constant Current):020 = 0.20 A; 021 = 0.21 A … 100 = 1.00 A … 150 = 1.50 A

Example: LTEA3D11KN-JA100For further assistance selecting your model number, contact Lutron Asuka at 03.5575.8411 (phone), 0120.083.417 (freephone), or [email protected]

LED Driver Output Range (see the following pages for more detail):Constant CurrentG = 0.20 A – 0.70 A 8 V – 20 VH = 0.20 A – 0.70 A 15 V – 38 VI = 0.71 A – 1.05 A 8 V – 20 VJ = 0.71 A – 1.05 A 15 V – 38 VK = 1.06 A – 1.50 A 8 V – 20 VL = 1.06 A – 1.50 A 15 V – 38 V

LTEA3D11K — – — — ———



Job Name:

Job Number:

Model Numbers:


369677e 4 08.07.2015

“G” Output Range, Current Driver Models

Driver Type Output Dimming Method Output Voltage Output Current Output Power Standards RecognitionConstant Current Driver (Class 2)

Pulse Width Modulation (PWM) 8 – 20 V 0.20 – 0.70 A 2 – 14 W HConstant Current Reduction (CCR)

Typical Performance Specifications:

Parameter Value Test ConditionsInput Current 186 mA ta = 25 °C,

0.70 A 14 W load, Max. Light Output, K enclosure 100 V~ without a control

Power Factor 0.99THD < 20% for loads greater than 10 WDriver Efficiency 76%

Effi

cien

cy (%

)

80

75

70

65

60

55

50

45

40

Driver Efficiency vs. Output Power at 100 V~

2 4 6 8 10 12 14Output Power (W)

0.20 A

0.35 A

0.50 A

0.70 A

Out

put V

olta

ge (V

)

60

50

40

30

20

10

0

Output Voltage vs. Output Current

0 0.35 0.7 1.05 1.4 1.75 2.1Output Current (A)

G

Out

put P

ower

(W)

40

35

30

25

20

15

10

5

0

Output Power vs. Output Current

0 0.35 0.7 1.05 1.4 1.75 2.1Output Current (A)

G

20 V Max.

8 V Min.

0.2

32

3

1.50.2

38

8

1.5

Current Driver Operation Range:



Job Name:

Job Number:

Model Numbers:


369677e 5 08.07.2015

“H” Output Range, Current Driver Models


Pulse Width Modulation (PWM) 15 – 38 V PWM0.20 – 0.70 A 3 – 26 W HConstant Current Reduction (CCR) 15 – 38 V-





Effi

cien

cy (%

)

85

80

75

70

65

60

55

50


0 5 10 15 20 25 30Output Power (W)

0.20 A

0.45 A0.70 A

Out

put V

olta

ge (V

)

60

50

40

30

20

10

0


0 0.35 0.7 1.05 1.4 1.75 2.1Output Current (A)

H

Out

put P

ower

(W)

40

35

30

25

20

15

10

5

0


0 0.35 0.7 1.05 1.4 1.75 2.1Output Current (A)

H

38 V Max.

15 V Min.

0.2

32

3

1.50.2

38

8

1.5




Job Name:

Job Number:

Model Numbers:


369677e 6 08.07.2015

“I” Output Range, Current Driver Models







Effi

cien

cy (%

)

80

75

70

65

60

55

50

45

40


0 9 12 15 18 21 Output Power (W)

0.71 A1.05 A

Out

put V

olta

ge (V

)

60

50

40

30

20

10

0


0 0.35 0.7 1.05 1.4 1.75 2.1Output Current (A)

I

Out

put P

ower

(W)

40

35

30

25

20

15

10

5

0


0 0.35 0.71 1.05 1.4 1.75 2.1Output Current (A)

I

20 V Max.

8 V Min.

0.2

32

3

1.50.2

38

8

1.5




Job Name:

Job Number:

Model Numbers:


369677e 7 08.07.2015

“J” Output Range, Current Driver Models






Power Factor 0.99THD < 20%Driver Efficiency 80%

Effi

cien

cy (%

)

90

85

80

75

70

65

60


10 15 20 25 30 35 Output Power (W)

0.71 A 0.90 A

1.05 A

Out

put V

olta

ge (V

)

60

50

40

30

20

10

0


0 0.35 0.7 1.05 1.4 1.75 2.1Output Current (A)

J

Out

put P

ower

(W)

40

35

30

25

20

15

10

5

0


0 0.35 0.7 1.05 1.4 1.75 2.1Output Current (A)

J

38 V Max.

15 V Min.

32 V Max.

0.2

32

3

1.50.2

38

8

1.5




Job Name:

Job Number:

Model Numbers:


369677e 8 08.07.2015

“K” Output Range, Current Driver Models







Effi

cien

cy (%

)

80

75

70

65

60

55

50

45

40


0 11 13 15 17 19 21 23 25 27 29 Output Power (W)

1.06 A 1.20 A1.50 A

Out

put V

olta

ge (V

)

60

50

40

30

20

10

0


0 0.35 0.7 1.05 1.4 1.75 2.1Output Current (A)

K

Out

put P

ower

(W)

40

35

30

25

20

15

10

5

0


0 0.35 0.71 1.05 1.4 1.75 2.1Output Current (A)

K

20 V Max.

8 V Min.

0.2

32

3

1.50.2

38

8

1.5




Job Name:

Job Number:

Model Numbers:


369677e 9 08.07.2015

“L” Output Range, Current Driver Models






Power Factor 0.99THD < 20%Driver Efficiency 75%

Effi

cien

cy (%

)

90

85

80

75

70

65

60


15 17 19 21 23 25 27 29 31 33Output Power (W)

1.06 A1.20 A 1.50 A

Out

put V

olta

ge (V

)

60

50

40

30

20

10

0


0 0.35 0.7 1.05 1.4 1.75 2.1Output Current (A)

L Out

put P

ower

(W)

40

35

30

25

20

15

10

5

0


0 0.35 0.7 1.05 1.4 1.75 Output Current (A)

L

15 V Min.

32 V Max.

0.2

32

3

1.50.2

38

8

1.5




Job Name:

Job Number:

Model Numbers:


369677e 10 08.07.2015

K Case: Case Dimensions

K Case: Connector Location Dimensions

A 107 mmB 25 mmC 76 mmD 124 mmE 117 mm (mounting center)

F 36 mmG 51 mmH* 28 mmI* 51 mmJ* 41 mm

K* 8.3 mmL 16.5 mmM 19 mmN 44 mmO 34 mm

* Applies to studded K case only.

P 19 mmQ 8 mmR* 7 mm

A

C

ED

J*

B

F

G

H*

I*

PO

N

Q

K*

K*

L

M

Q

R*

L

8 – 32 Threaded Studs*



Job Name:

Job Number:

Model Numbers:


369677e 11 08.07.2015

K Case: Side Entry Connector Location Dimensions (Non-Studded)

S

U

V

T

S 35 mmT 16 mmU 22 mmV 39 mm



Job Name:

Job Number:

Model Numbers:


369677e 12 08.07.2015

Wiring Diagram for Forward Phase Control

1 Fixture and driver case must be grounded. 2 For maximum driver–to–LED light engine wire length, see chart in Driver Wiring and Mounting section.

Note: Colors shown correspond to terminal blocks on driver.

To Forward Phase Dimming Control

Dimmed Hot (Black)

Ground1 (Green)

Ground1Neutral (White) –V2 (Black)

Hi-lume® A-Series

+V2 (Red)

LED light engine



Job Name:

Job Number:

Model Numbers:


369677e 13 08.07.2015

Compatible Controls

• Guaranteed performance specifications with the controls listed in the chart below.• For assistance selecting controls, contact Lutron Asuka at 03.6866.8444 (phone), 0120.083.417 (freephone), or

[email protected]

Product Part Number Fixtures per Control (100 V~ only)

Measured Light Output Range

HomeWorks® 500 W dimmer HWD-5ND-JA 1 – 8 100% – 1%GRAFIK Eye® QS1 QSGR-3PJA

QSGR-4PJAQSGR-6PJA

2 – 10 (per output) 26 total per unit

100% – 1%

GRAFIK Eye® 30002 GRX-3102-x-JA-xxGRX-3103-x-JA-xxGRX-3104-x-JA-xxGRX-3106-x-JA-xxGRX-3502-x-JA-xxGRX-3503-x-JA-xxGRX-3504-x-JA-xxGRX-3506-x-JA-xx

2 – 10 (per output) 26 total per unit

100% – 1%

RPM-4U Module3 (LCP Combo, GRAFIK SystemsTM)

LP-RPM-4U-120 2 – 26 (per output) 26 total per module

100% – 1%

RPM-4A Module3 (LCP Combo, GRAFIK SystemsTM)

LP-RPM-4A-120 1 – 13 (per output) 26 total per module

100% – 1%

GRAFIK SystemsTM Dimming Panels3 GP-4-2L-JAJDPxx-xxxxx

1 – 26 (per output) 100% – 1%

1 Set load type to “Fluorescent Module”2 Set load type to “GRX-FDBI or GRX-TVI”3 Set load type to “ 2-1”



Job Name:

Job Number:

Model Numbers:


369677e 14 08.07.2015

Electricians and Contractors

Driver LeadsMaximum driver-to-LED light engine wire length for Constant Current Drivers:

Wire Gauge ØMaximum Lead Length

200 mA to 700 mA 710 mA to 1.50 A1.024 mm (18 AWG) 9 m 4.5 m1.29 mm (16 AWG) 10.5 m 7.5 m1.63 mm (14 AWG) 15 m 12 m2.05 mm (12 AWG) 30 m 18 m

Note: For wire gauges larger than Ø 1.29 mm (16 AWG), use external connector for connection with driver

Wiring and Grounding• Driver must be grounded.• Drivers must be installed per national and local

electrical codes.

LED Light Engine ReplacementThe LED light engine can be changed while the driver is installed and powered.

Maximum Driver Operating TemperatureFor 50,000 hour lifetime, driver case temperature (tc)must not exceed 65 °C.

Facilities Managers

SERVICE

WarrantyFor warranty information, please contact Lutron Asuka.

Replacement PartsWhen ordering Lutron® replacement parts please provide the full model number. Contact Lutron Asuka if you have any questions.

Further InformationFor further information, please visit us at http://www.lutron.jp.You may contact Lutron Asuka at: 03.6866.8444 (phone), 0120.083.417 (freephone) or [email protected]

hi-lume a-series driver overview forward phase control · pdf filehi-lume ® a-series...

Documents